Surely, each at least once came across the problem of creaking floors, or in a public place, or at home. This attack creates simply unbearable conditions - no personal life. A sharp whistling creaking is informant about your home movement not only of your household, but sometimes neighbors. Involuntarily arises a natural question how to eliminate the creaking of parquet. Despite the excellent performance of the wooden coating, its naturalness and environmental friendliness, still over time and it requires repair. The most reliable remedy for the vicious parquet is its complete replacement. But not everyone can afford such expenses at once, therefore, to temporarily eliminate the violin, one of the following methods can be used.

Causes of the screenshots of parquet

To qualitatively perform the repair of the screenshot of the parquet and choose the way it is necessary to precisely identify the cause of the screens and its location. All the reasons for the appearance of squeaks can be divided into two categories: those related to non-compliance with wooden floor laying technology, and those associated with poor-quality wooden flooring wood or improper operation of a wooden coating. Due to the fact that the tree is a natural living material, it "breathes", picks up moisture from the room and gives back. If the premises did not comply with the optimal humidity mode or laying of the floor was made poorly, the wood planks begins to deform. This leads to the appearance of creak and even deformations of the planks.

Errors in parquet floor laying technology:

• There is no smooth base.
• The substrate of fiberboard or plywood adjacent to the concrete base.
• Improper location and size lag.
• Insufficiently fixed lags.
• Deformation lag.
• Parquet planks are fixed on poor-quality glue.
• No compensation gap between the parquet and the wall is not fulfilled.
• Plinth is incorrectly fixed.

Speeding or timing of wood parquet planks:

• Initially, poor-quality material - wood is not sacrificed or overpower.
• During operation, the optimal humidity and temperature regime was not observed. As a result, the parquet is sneaking or deformed from frequent "wetting" and then cutting.
• Washing parquet from vapors going from below. The reason is the non-compliance with the laying technology - a vapor barrier membrane was not used.

Such a large number of reasons for the appearance of a screen obliges to know exactly what the wooden parquet floor is consisting of the cake in your home, as well as the option of its installation and the fasteners used. This depends on the method of eliminating the screens, which can be used in one or that case.

How to get rid of the screenshot

You can allocate a few places where the creak is formed:

1. Parquet planks will creak from friction about each other.
2. Parquet strips rub about the substrate.
3. Parquet planks rub about nails with which they were fixed.
4. The creak makes a substrate that is loosely adjacent to the base.
5. The creak is published lags.

Since you have decided to eliminate the screenshot of the parquet with your own hands, try to accurately determine the cause of the squeak and choose a suitable way to combat it from below.

If conjunction pair parquet

The panel parquet is the squares 50x50 or 60x60 cm, consisting of wooden base planks and parquet slats, glued to them from above. Most often, the base itself is a two-layer and rows of planks in it are located perpendicular to each other, i.e. If one is longitated, then the second transverse. All layers of wood are bonded with an adhesive joint. Parquet shields can be quickly and easy to mount to lags. It is thanks to convenience in many typical apartments in Soviet times laid a panel parquet. Unfortunately, this type of parquet fails faster than the classic and practically no restoration.

The shield parquet may have two troubles:

The first - shields are loosely adjacent to lags, which in turn do not have the best geometry and installed on elastic lining. With such a problem you can fight, although it is difficult. First you need to determine the location of the lag. Then fasten to them shields tightly. In the corners of the shields, holes are performed with a depth of 15 - 20 mm and a diameter like a screw screw for a dowel. Then the holes are deployed through the entire pie - shield and lag. Plastic spacer dowels are inserted into them, and then screwed screws. The screw of the screw should be recessed in the parquet bar minimum 15 mm. The remaining opening is stuck in a wooden plug and put on a putty to the tone of the parquet. Of course, all this procedure must be performed only with those shields that creak.

The second - due to the deflection of the shields, the layers of the planks fucked and peelled, the boards at the bottom of the shields could crack or split, boards and parquet strips rub each other, making a creaky sound. In other words, all three layers of the parquet shield were smelled. Such trouble, unfortunately, is not treated. If you have exactly such a case and you are interested in how to eliminate the creaking of the old parquet, then the answer is only one - replace it.

If the substrate (plywood, fiberboard) is loosely adjacent to the base of the floor

As it often happens, during construction or repair, many neglect the requirement to perform an aligning lighting of the floor with cement-sandy solution. As a result, the plywood is stacked on not too smooth concrete floor, it is glued or screwed to the base, and everything seems to be good ... until time. Due to the constant mechanical loads in the passage zone of the plywood, it is peeled from the concrete floor and begins to "fierce" and "squat" on it.

The ways to solve the problem are several:

Method 1. Harding under the Phaneur cement milk. In the intensive screensions, which need to be determined in the place: in the place of the alleged screen, to install a load of 80 - 100 kg, if the creak disappeared, it means that the place is defined correctly. In the required place, you must remove several parquet slats if they are firmly held on the ground, you will have to donate one of them. For this, the parquet bar is split into three parts and removed. Then in the substrate (plywood, dvp) a hole is drilled by about 20 mm in diameter. Cement milk is mixed (1 part of cement + 1 part of the water) and poured into the hole until the solution starts to pour back. Next, the solution must be given at least a day to dry. Then the remote sheets of parquet are glued to the plywood, and the split must be replaced with a new one.

In this method, you can make an adjustment - the planks of the parquet can not be removed, but drove the hole through them. Then it will have to shut up a chopper from the same wood as a parquet, and put on with putty.

Method 2. Pulling under the paneur of the assembly foam. At the place of a loose fit, the plywood drills a hole in which the mounting foam is injected into two navigations: after the first one must take a break no more than an hour. Then the hole must be plugged with a cutlets and set the load at least 150 kg so that the mounting foam does not swallow the entire floor.

Method 3. Removing the screen of parquet by screwing the parquet together with plywood to the concrete base with screws. To perform work, you will need a bars of 50x50 or 50x75 mm long as the ceiling to the floor. One edge of the bar is pointed in the form of a fifth, a size with a five-fucked coin (2 cm diameter). In the estimated area of \u200b\u200bthe screens, the timber is installed, the upper edge must be restricted into the ceiling. For a stronger stop between the timber and the ceiling, a wooden strut is embedded. Since initially the timber was taken up with a length equal to the distance from the floor to the ceiling, he would not be able to become smooth, and would have some bias. It is necessary to continue to pour a bar until it becomes smoothly, and the floor is as much as much as possible to the base. If, after the proceeding procedure, the creak in this place disappeared, then you must need to screw the screw.

Before screwing the screw, you should check the rest of the floor for the screenshot. And in places where it will be discovered to do the same procedure with a bar. When there will be no screenshots throughout the floor area, the number of necessary screws is calculated.

Sculp should be such a length to go into a concrete base by 40 - 50 mm, and the hat should be recessed by 5 - 7 mm in the wood.

First, the hole is drilled with a diameter equal to a screw screw, a depth of 5 - 7 mm. Then the hole of the depth equal to the length of the screw and the diameter equal to the diameter of the plastic spacel dowel is drilled. The dowel is inserted into the hole, screws the screw. The washer is put under the screw head to ensure that the parquet bar is stopped. The same procedure must be repeated for all places. Then all the remaining openings are embarrassed by putting on the tree. In completion, the struts are cleaned.

I would like to note that when the squeak of parquet appears, the elimination of it in this way is the most reliable and durable. But it also increases the complexity of dismantling the coverage in the future.

If there are no gaps between the wall and parquet

There should always be compensatory seams of at least 15 mm between wooden floors and the wall around the perimeter of the room. If the parquet floor is mounted without complying with this rule, due to the temperature and humidity expansion of wood, the flooring of the parquet is starting to put pressure on each other, as it turns out to be routing between the walls.

Eliminate such a defect easily - cut off all over the perimeter 15 - 20 mm of wood and substrate. The main thing is that it was not too late. There are cases when, due to wetting, the parquet bar is exhausted and deformed finally without the possibility of repair.

If the concrete base has significant irregularities

Perhaps this problem is one of the most difficult, since it does not imply a half-term. If there was no floor screed before laying the floorboard and the concrete base has significant height differences, it will have to fully disassemble all the coating to the very base. Then the surface is aligned with a cement-sand mixture, after its drying, the substrate is laid and from above - a parquet board. In fact, you have to make a completely new parquet floor.

If the plates of the parquet quit and gaps were formed between them

The sinking of the planks of the parquet is the result of them to lay the unrown. The planks were deformed and now rub each other about the base / substrate. You can eliminate the creaking of the parquet in this case, without letting the straps rub on each other and "fool". For this wooden wedges are driven between the planks So that their upper edge does not play the surface of the parquet. The step between the wedges is made 15 - 20 cm. Then the space between the straps is closed with putty.

If the planks of the parquet detached from plywood or fiberboard

How to remove the creaking of parquet if his planks detached and rub about the base? There are several effective ways here.

Method 1.. In places where the planks of the parquet moved away from plywood, it is necessary to stick slices of painting scotch. If the area of \u200b\u200bthe screen is a large point with scotch, it is necessary to position with a step of 20 cm. Then, in the sale of a piece of painting tape, a hole with a diameter of 2 mm depth to plywood is made. The drill must break through the scotch, as a result, a small hole is formed. With the help of a conventional syringe without a needle into the hole introduced glue. It can be a special glue for plating parquet, and there may be another glue for working with wood, for example, PVA. Slowly, slowly glue pushes into the cavity between the parking plank and plywood. After filling the cavity of the glue, it is necessary to give an hour to dry. Then the greasy tape is removed, and if the glue stains remained on the surface of the parquet, they must be removed using a solvent, and then wipe the floor with dry rag.

The glue dries 24 hours, all this time at the repair plots should be load (50 kg). After complete drying, the glue of the holes is filled with a putty on a tree or wax and polished.

Method 2. In the field of screenshots, parquet strips are fixed stilesusing a pneumaticist.

Method 3.. Remove creaking parquet strips, in their place put a piece of cardboard, and on top to secure the bar. In this case, the parquet can be fastened both on glue and with the help of self-tapping screws, hacking them with 5 mm caps in wood.

Method 4.. Everything sharing parquet planks screw to base (plywood / fiberboard) by self-draws. It is desirable to sew holes for the self-tapping screws not exactly, but at an angle of 45 °. Do not forget that the hats of self-tapping screws must be dragged into the floor. And on top to sharpen.

The problem described above is the simplest among all, as in the extreme case, you can delete all the detached parquet strips, clear the base and glue them again, but already high-quality glue.

If lags are deformed

The deformation of the lag of a wooden floor is the trouble, since, most likely, the reason for the wet of wood from vapors coming out of the room below. Elimination of the screenshot of the parquet in this case will not solve the problem. The only possible case is to dismantle the parquet, check the base of the floor, lay a vapor insulation film, securely fasten the lags. If the lags are deformed too much, then they must be replaced, otherwise after a short time you will come across the problem of squeaks.

If the parquet board runs about lags

An effective way to eliminate the script of the parquet board, if it runs about the lags, is broach self-timers. The main problem is to determine exactly where these lags are held, and whether there are any communications in them. Secure the parquet board to the lag is necessary on both sides, as shown in the photo. Holes under the self-tapping screws are drilled at an angle of 45 °, the fasteners themselves should seem to look at each other. One board with a length of 1 m will have to make at least 6 fasteners. Do not forget to draw the hats in the wood.

In addition to this, sometimes in the gap between parquet boards, talc or sand fall asleep to reduce the contact of the board and lags.

If a comb or groove in the parquet board broke

The main task in this case - spray parquet boards. To do this is used selfless. This method is similar to the previous stretcher with self-draws, only in this case the self-tapping screw should be short, so to connect two boards with each other diagonally. The holes are drilled with an indentation of the edge of the 1 cm board, at an angle of 45 °, so that the tip of the self-pressing is entering the adjacent board for about 1 cm. Neighboring Selfness should have the opposite direction - from the neighboring board to the first.

If the parquet planks are free "go" on nails

The mounting of the parquet on the nails is associated with one very significant disadvantage - when the wood is sneaking, it will smoothly "walk" on the smooth surface of the nail, and that simply ceases to keep it. And although immediately after installation, nothing foreshadows troubles and everything keeps well, with time your idyll may break a terrible creaking tree about metal.

Unlike the nail surface, the surface of the self-press has a spiral cutting, so the wood is firmly held in one position, even if a pair of millimeters occurs. To eliminate the violep of parquet slats or nails boards, you must complete the full bulkhead of the parquet and replace all nails with screws.

If he dryed and the bituminous mastic, which was attached to parquet

The most extravagant way to eliminate the vigilant parquet is associated with the problem of drying bituminous mastic, on which parquet was attached to Soviet times. Bituminous mastic over time becomes fragile and crumbs, such a material is not able to hold the planks. To restore its properties can be tried heat mastic using hairdryer. Thoroughly warming up the entire surface where the creak is observed, it is necessary to firmly press the parquet strips to the base, and for this you should evenly decompose the cargo.

Another way to eliminate the screenshot of the parquet in this case is similar to those that have already been described above. It is necessary to perform holes in the parquet, download the glue under it, and then attract parquet boards with screws or screws.

In conclusion, I would like to recall once again that the elimination of the screenshot of the parquet with their own hands using the presented methods is only semi-dimensions. Do not put a different coating on top of a creaking wooden floor, such as linoleum or cork floor or laminate. Just imagine that after some 5 - 7 years, it will have to disassemble everything to the base, sniffing the layer behind the layer. It is better to immediately make a full-fledged overhaul and replace the fairly creaking parquet.

Parquet is considered one of the most reliable and durable coatings. However, repair may require this type of finish. Sometimes it is associated with improper operation, more often with the wrong. The most common damage to the parquet is the bloating and creaking of the dice.

From time to time you have to eliminate and scratches, as well as cracks and chips. On how to restore the parquet with your own hands and return it an initial attractive look further read further in the article.

Of course, it is possible to repair this expensive coating correctly, only subject to the exact following technologies.

Parquet - the coating is beautiful and in repair quite complicated

How to remove scratches on the floor

Scratches are the easiest form of damage, eliminate which is not so difficult. What should be done if the wooden floor scratched? In this case, you need to carry out such operations as. Such a repair of parquet is performed using special equipment.

How to update the wooden floor. Photo of grinding machine

Wood floor repair: how to get rid of cracks and chips

Next, we will deal with how to update the parquet in the apartment in case of detection on it cracks and chips. Such defects appear as a result of improper operation of the floor covering. Parquet is dry and cracks most often in rooms with too dry air.

In the room with a very dry air will soon have to do repair of parquet, as cracks will appear on it

This type of damage is eliminated using a special wood putty. Parquet repair is performed in several stages:

1. Pre-floor quincional. As a result of this operation, the old varnish is removed and the top darkened wood layer is removed.
2. The restoration of the parquet continues to eliminate cracks and chips. What to livel such damage? Repair produce by sealing them with a putty on the tree of the corresponding parquet of color.

Cracks on dies when repairing a wooden floor is lubricated with a putty on a tree

1. Next, the sealing of cracks and chips are performed using a spatula.
2. After the putty gets up, it is sanded.

Putty on the sealed dies when repairing is handled by sandpaper

1. Next perform grinding and.

In the same way, the parquet is restored if the dent appeared on it.

The parquet creaks. What to do?

The creaking of the dice is the phenomenon characteristic mainly for the old one. In fact, the creak - the payroll for the ecological purity of the floor covering. Over time, natural wooden elements dried slightly and leave the substrate. As a result, when walking on the floor and an unpleasant creaking occurs. Of course, such a parquet requires repair.

The creak causes the departed parquet dies

Sometimes the script appears and because of the crack of the crest or unscrewing fastening screws. Restoration of parquet in this case is performed depending on the type of damage. Most often, the elements are made, because of which creak occurs, and it is necessary to glue. In the case of a ridge, the coating update and the elimination of the violep is performed by replacing the element.

Screenshot removal technology without opening parquet

First, let's deal with how to remove the creaking of the parquet without dismantling the dice. If, when walking on the floor, the creaking or coating is heard, first of all, it is necessary to determine the place of waste of the elements by climbing the floor with a wooden hammer. Next, the holes in diameter of 0.4-0.6 cm drill in the corners in the corners.

How to restore parquet. To get rid of the screens in the dies pre-drill holes

The elements need to be drilled through and not to damage the substrate. To eliminate the creaking of parquet without autopsy, at the next stage in the holes the syringe pumped PVA glue. After the bay, wooden chops insert into the holes and put something heavy to the departure place.

To eliminate the violep when repairing under parquet pour glue

After gluing the elements, the places with the Crescents need to be accurately walked and sand. To fix the floor, when removing the screenshot instead of PVA glue, a polyurethane can be used.

Elimination of a violence by dismantling parquet

About how to eliminate the creaking of parquet without his disassembly, you now know. In the event that this operation is not crowned with success, in the place of waste, the elements will have to be glued again. The creak is eliminated in several stages:

1. Reconstruction begins with a split one of the dies. Do it with the help of a toporist.
2. Next, it is removed and disassemble the remaining elements.

Sometimes the creak can be eliminated only by removing the dies and their subsequent stickers.

1. Continue repairing the remnants of glue from the pit.
2. Next stratum substrate.

1. Then the dies must be brushed from dirt, wrapped with glue and install in place. After they are securely fixed, the creak will be guaranteed.
2. The place of split the extreme element is smeared with putty and sandwiches.

Curr of the dice sometimes can be eliminated, just aligning the screed

Here is this way and the elimination of the vicious parquet is performed by the bulkhead.

How to repair a swollen parquet

Another frequent reason for the need for such an operation, as the repair of floors, is the bloating of the parquet. Why can such a trouble happen? There are similar problems usually as a result of a sharp increase in air humidity, flooding, or moisture penetration from the lower floors of concrete capillars.

Repair of parquet may be required due to his bloating

In the first two cases, the cause of dice wasis is usually poorly gluing them to the substrate. With an increase in air humidity, the tree swells a little, as a result of which poorly fixed elements simply come off from the base. In this case, the recevance of the parquet is performed by smugging problem areas.

Repair of parquet at bloat is performed by brute force dice

If the floor swelled as a result of the impact of capillary moisture, the restoration of the parquet is carried out with their own hands by its full disassembly. Such a nuisance can occur only if the waterproofing layer was not mounted when laying the parquet. A simple dice bulkhead when repaired in the disclosed places, the problem will not solve. The floor sooner or later still starts to worry. Repair in the event that the parquet rose, it is produced like this:

• Start the recovery of the parquet with their own hands from the split one of the dies in the corner of the wall of the room.
• The coating is disassembled. Well glued dies are torn off, fashioning the spatula.
• Screwdriver unscrew the screws of the substrate.
• Continue to repair the dismantling of plywood sheets.
• Next comes the screed.

Waterproofing screed when repairing the floor can be done using a plastic substrate

• At the next stage, a polyethylene film with an overlap at 15 cm is superimposed on the purified overlap.
• A new screed is arranged.
• A dried plywood is mounted on it.

Phaneur need to dry and put on the screed

• Finishing the repair of the assembly of the parquet.

Finally, we suggest you see how to make the repair of parquet with your own hands. The video demonstrates this process step by step. After reviewing it, you can better understand how to eliminate the screens and swollen with a syringe and putty.

This is the way there is an independent recovery of parquet. Make repair and replace items needed carefully, observing all the implemented technologies. Remember that the purchase of new dies instead of spoiled will cost, most likely not cheap.

The creaking is considered the most common parquet floor defect. Moreover, the sounds can publish both local areas and all coverage of the whole. How to make outdoor material silence? First of all, it is necessary to deal with "singing", and then look for ways to eliminate it.

To begin with, we define the terminology. Parquet floor include:

• Classic piece planks made of array stacked for glue or hardware;
• Parquet board multilayer, mounted "floating", less often - adhesion method;
• Massive (solid) floorboards, which are attached to the base with gluing or fasteners;
• Shielded parquet or engineering array, fixed by all three ways: Castle, adhesive, meticible.

Conditionally reasons can be divided into three groups:

Montage errors

Manufacturers are trying every way to convey to buyers that products from wood must be treated according to the instructions developed on the basis of engineering solutions and perennial studies. But, unfortunately, most of the masters prefer to make stacking the most convenient way for themselves. Result: Parquets in the apartment from the slightest movement creaks annoyingly and the question is sharp - what to do?!

In the list of factors of this group:

• Violation of basic requirements for the formation of structures for lagham floors. In particular, it may be too long between the elements, a rare fastener, a poor-quality or deformed support, no waterproofing and the like. To fix this type of error, you will have to fully disassemble the floor and look for the causes visually, and not for rumor.
• The use of electrical (cable) floor heating system. Too high point heating spoils the bar, causes an uneven change in geometric sizes. And there is no solution, how to get rid of the screen of parquet, except for disconnecting heating or eliminating the inefficient minimum.

Wear construction

The parquet floor with time agitates, needs to be restored. In particular, there is a place:

• Deformation (drying, unscrewing), destruction of coating planks, supporting lags, plywood;
• Sailing the substrate (when laying a "floating method");
• DISPLAYING ELEMENTS OF THE STAR PARKET;
• Sharing or loss of fasteners (nails, spills, screws).

Wood features

A number of factors associated directly with the characteristics of the outdoor material can be distinguished into a separate group. In particular, the creaking floor may be a consequence of an incorrectly selected breed or variety of wood. For instance:

On the emergence of foreign sounds, even the level of humidity in the room is affected. In the winter period, when the heating system is enabled, the percentage of moisture content in the air decreases, the planks are dissolved and begin to creak at the slightest load. In this case, special humidifiers will help.

How to eliminate creaking parquet

We are not in vain at the very beginning marked the methods of installation of floor coatings. This depends on the choice of the optimal method of repair.

Correction of coating shortcomings is conducted in several directions:

Elimination of foundation defects

It is easiest to work with the floor, which is formed by the "floating" method. It is enough to remove the plinth, carefully disassemble the material and take a partial or full repair of the base layer. In the first case, the tubercles should be placed, and the yams fill in a cement-sand or quick-drying mixture. In the second, experts recommend complete alignment of thin layer bulk mixtures.

If the parquet floor is glued or fixed with hardware, then the work is complicated. You can try to remove the shortcomings locally, that is, in the places of the strongest screen, cut the lamellas with the help of a cutting power tool or split the slap with a hammer with a chisel. Next damaged elements are removed, the base defect is corrected and a new parquet is glued.

For a massive floor formed by lags, the technique of elimination of defects implies:

• reducing the step of support bars and / or floorproofing material. The larger the distance between beams or slats, the greater the degree of sagging of the board and stronger creak. The optimal width is no more than 50 cm. To correct this lack, a complete disassembly of the coating will be required.
• replacing damaged elements. Twisted or stuck "hump" lags deform the finishing coating. Therefore, the floor must be removed, replace the supports. If the reason in the fallen or rusted fasteners, then you need to carefully examine the entire floor, change the locks to the new ones, where it is necessary to "attract" the boards to lags with additional nails or self-draws. The latter gives a good effect on old coatings, as over time, the lamellas are departed from supports and begin to creak strongly due to friction;

Formation of compensatory seams

This method is recommended for coatings mounted by the "floating" method. On the perimeter, you need to remove the plinth, cut off the edge of the lamella to the desired width (up to 10 mm, the exact width of the seam is specified in the instructions for the material). If there are swollen areas, the boards with damaged locks must be replaced with new ones. Or you can partially sort out the floor, add fixing elements (for example, to drive "studs" into the lock at an angle of 45 °), set back decorative moldings.

Flooring a new substrate or replacement of old

Locks of a parquet board or shield parquet are stretched over time. Therefore, during dismantling of the material, each bar is needed to numbered the marker to then collect the coating in the same order.

The disassembled floor temporarily needs to be removed from the room, carefully inspect the basis for the presence of defects, suitable and process to. Next, you need to unawrs of the waterproofing film with an adhesive 20 cm, mount the substrate and you can assemble the finishing material again.

Restoration of old parquet

Experts are recommended to carry out the full bulkhead of the parquet after 1-3 years of operation, since during this time the tree is fully acclimatized, all flaws will identify that can be easily eliminated. Of course, it is acceptable for coatings recorded on lock connections or fasteners.

What to do with the straps, who over time are deformed or dug? Here are two solutions:

• damaged elements remove, the splitting of the chisel with a hammer, incur new, joints to shake and restore the protective surface layer;
• if the plank is a whole, then you can drill a small hole in it, introduce a glue composition with a syringe, excess removed, fix the cargo by 12-24 hours. After the polymerization of the adhesive, close the gap with a putty or repair wax.

The video below shows how to remove the creaking of parquet, without removing it completely.

In the end, we note that the creaking of a parquet of any nature can be eliminated, if you find it thoroughly. Partial repairs like "attracting" coating to lags with additional fasteners give a temporary effect. After a few years, defects will again manifest. We will have to either completely sort out the floor material, or replace it with a new one.

Tip! If you need repair masters, there is a very convenient service for their selection. Just send in the form below a detailed description of the works that you need to perform and offers to you in the post office with prices from building brigades and firms. You can see the reviews about each of them and photos with examples of work. This is free and does not oblige anything.

Why starts to creak parquet? What to do to not creak? This is described in detail in the article.

These hopes for the durability of the parquet can only with regular care for it. This blog has a separate article. But even with careful prevention, troubles arise. For example, in the form of a squeak.

How to get rid of it - this is about this.

Causes of the occurrence of violin

Why creaks parquet if it is minimized recently? Any boards are subject to the problem - already in operation and absolutely new. The most common cause of the symbol becomes a violation of the technology of preparing the foundation before laying parquet - that is, at the very beginning of the path. It:

In addition to the listed reasons, the appearance of the screens is caused by a violation of the climatic regime. In room with parquet, it is important to install a split system in advance if the owners are preserving expensive coating. Otherwise, to keep track of yourself behind the humidity and dryness of the air - it will not work. What to do to not creaked parquet - Next, answers.

Solution of problems

The correct solution of the issue is how to get rid of the screenshot of the parquet board, would dismantle the entire parquet area and styling it again in compliance with all stages of technology.

With floating floors - parquet with castle connections without dead adhesion with a base - it is possible. With the rest - not always. There are several methods that help correct the situation without resorting to the fundamental measures. Details:

Determination of a symbol location

• The defect can occur both when walking and without movement (then it is about the cod of the boards). In the first case, the definition is simply - to eliminate the cause follows in places of pressure. In the second, it is important to inspect all the coverage - the analysis most accurately determines the cause. So:

• The sweat of the parquet board speaks of the fascinated planks, a loose fit of their friend, the absence of gaps between the parquet and the wall.
• The seasonal occurrence of the screen will say about the impairment of humidity in the room, insufficient warming or sealing of technological openings - windows and doors.
• Check-down strips indicate poor quality of glue or lack of primer based on.

When the site is defined and the cause of the screen is clear, you can proceed to liquidation.

Elimination methods

The parquet board from old-age creaks more often. In this case, the complete restoration of the floor area will be required. This is done independently in the case of a standard board or, causing specialists if the coating has artistic value.

If the laying has occurred recently, and the parquet still creaks, use the following:

• Partial disassembly with definition of base drops.
• Installation of gaps between parquet and walls.
• Installing new boards.
• Overflow of varnish coating.
• Installation of pins.

The described methods decides the question - what can be done in order not to creak parquet. To ensure complete elimination of the screens, perhaps only with a scrupulous approach. Details about each:

In some cases, the quality of parquet, base or installation - no complaints cause. However, why creaks parquet board after laying? Perhaps the case in fasteners - self-tapping screws are often the cause of the problem. Then they are changed on nails. We will have to pull the canvas piety, but the result is worth it. But as practice shows, immediately after laying parquet, the parquet will be built for two reasons: 1) the quality of laying and 2) the quality of surface preparation.

Prevention of violin

• Observe the rules for laying parquet if the work is carried out on their own. Either order the service to specialists, where the guarantee for trouble-free operation is given.
• Regularly check the condition of the parquet - not to bring a quiet creak to a priviless.
• Exercise proper care for each type of parquet board.

In order not to solve the question of how to eliminate the script of parquet with your own hands, it is important to scrupulously approach the selection of the board if the coating is still mounted. The higher the quality of the goods, the greater the probability durability of the wooden expensive floor.

Conclusion

The creak of parquet occurs - a signal for immediate elimination. The lubrication of the seams with wax or other is practically nothing gives - the problem is deeper. The connivation will lead to a damage of the coating, will create discomfort. Remedy methods are not relieved and effective if they are not pulled with the correction of the position.

If you have found a mistake, please select the text fragment and click Ctrl + Enter..

Parquet floors look spectacular and beautiful. They are easy to care and serve for many years. The appearance of squeaks is a signal about serious floors.

Due to the uneven evaporation of moisture from the massif of the parquet strip in some places, cavities can be formed between the parquet itself and the base on which it is laid. In such places, the coating begins to "play".

Even the minimum movement of the wooden parquet plank is already enough to occur. From the article you will learn why the floor creaks and how to eliminate the creaking parquet.

The creak arises as a result of friction of wooden surfaces. When a person goes on this floor, the planks of the parquet shift and rub against each other or about the base, from here creak appears.

The design of the parquet floor is that no shifts of the planks should not be in it. Therefore, the work on the elimination of the screens in the parquet floor includes the correction of the defects of the base.

What to do if the parquet creaks, we'll figure it out in the following sections.

How to eliminate the causes of the screens

To eliminate the causes of the screens, preparatory actions are performed first, and then the elimination of concrete base defects.

Preparatory actions

In preparatory actions, spend the following activities:

1. Draw a room plan. Come on the floor and tick the site of the appearance of the screen on the plan.
2. Remove the plinth. Be careful not to damage the parquet or plinth.
3. On the room plan, mark the order of laying parquet, remove it and remove it into another room. Try to reduce the number of damaged parquet slats.
4. Come on the substrate. If the symptops disappeared, the problem is in a weak fastening of parquet slats or breathing them.
5. The ongoing creak signals the weak fastening of the substrate to the base.
6. Remove the substrate and inspect. If mold is present on one element, dark spots, marching traces, all the coating must be replaced. If the sheets of coating without traces of damage, mark them not to confuse when installing and remove to another room.
7. Purchase parquet in the store similar textures and size to replace damaged slats.

To fully eliminate the causes of the screen of parquet, performing all the items of preparatory actions.

Elimination of concrete base defects

After removing the substrate, remove the remnants of glue from concrete. Inspect the reason to detect lojers, pits, cracks. When cracks are detected, expand one of them to get to the floor on which the base is flooded. If the floor is concrete, fill the crack with a solution of "liquid floor" or polymer putty (filling) for concrete. If the floor is wooden, remove the screed to repair the floor.

Ruffiness Remove with an iron brush, a nozzle to a corner car (grinder) to remove rust or electric chisel. Remove the remnants of glue. Clean the coating from dust and dirt. Using a 2.5 meters long line. Check the height difference. With a difference over 2 mm, 2 meters pour on the concrete base of the self-leveling screed.

Elimination of wooden floor defects

Repair Lag.

Elimination of the violep of the parquet board is impossible without quality repair of the base of the floor.

Remove the coating boards, mark and inspect them. Cracked, with places of mold, unpleasant smell remove, they will require substitutions. The rest are removed into another room.

Inspect the lags. Boards with cracks, traces of rot or mold, replace. Inspect the subfield. If it smells like damp, dry the heat cannons. The duration of this operation reaches one month, depending on the amount of moisture and power of the gun.

After drying, check the strength of the fastening of the lag in the wall. To do this, shake them. In the presence of vibration and knocks, raging them by driven by wooden wedges between the lags and the walls of the niches in which they are installed. Laid on brick or stone stands, as well as on the concrete base of lags in such an inspection do not need.

Fixing lags, a line of 2.5 meters long check the height differences. Having found a difference more than 2 mm by 2 meters, try lifting the lags below the rest. To do this, take a thin wedge between the bottom of the lags and the bottom of the wall niches. After each strike, the hammer check the height of the ruler.

Repair of rough floors

Place the removed elements of the draft floor. Replace damaged using the appropriate sizes. Use the board to replace the floorboard to replace plywood - Phaneur. After styling and fixing the draft floor, check the height and horizontal differences. With a drop of 2 mm by 2 meters, stabbing the floor or pour the thin layer of the self-leveling screed or the polymer material "liquid floor".

Use screws for fastening the draft floor. The mounting of nails will weaken in 2-3 months and the screens will return.

Choosing the right substrate

The substrate is needed to increase the parquet floor fortress. For the substrate use:

• self-leveling floors;
• rolled technical cork;
• phaneur;
• wood chipboard (chipboard);
• warm plate (Fiberboard).

For the base with a drop of heights of less than 1 mm, 2 meters is suitable for any of the materials. The effectiveness of the substrate of them is the same. With a drop of heights from 1 to 3 mm 2 meters better than others, the bulk sex and plywood are suitable. With a drop of heights from 3 to 6 mm for 2 meters, apply only the bulk sex. When the height difference is more than 6 mm for 2 meters, align the surface with self-leveling screeds. Place or pour the substrate over them. The incorrect substrate selection will lead to the fact that the parquet board will creak after 2-3 months.

Laying parquet.

Follow the room in line with the former parquet. Stacking start from the center of the room. Do not lay the parquet on a non-help substrate, the adhesive connection will weaken in half a year and the screens will return. Before laying, clean the parquet planks from the traces of glue and dirt. If the parquet during the dismantling had increased humidity, dry it in a ventilated room without drafts at a temperature of 20-25 degrees within a month. Dry parquet stacked as the substrate readiness.

Parpet operation

Parquet absorbs water, increasing in size. This leads to a change in the geometry of the design of laying, torn glue and the appearance of squeaks. Therefore, avoid strong parquet moisturizing. For floor washing, use a wet, but not wet cloth. This will prolong the service life of the parquet and will save you from the appearance of creak.

Parquet sections are associated with base defects, laying errors and incorrect coverage. Weakly fixed lags, concrete looseness, insufficient stiffness of the substrate mounting to the base or black floor lead to the mobility of parquet slats and the appearance of creaks and a knock.

Troubleshooting a parquet board is always associated with the repair of damage causeing this creak. By eliminating the reasons for the mobility of the floor, you get rid of squeaks and prevent their appearance for the next three to five years.

Video - What can be done if a parquet creaks: