Road installation services are sometimes expensive expensive. To save, use the portal instructions. The site, thanks to which any home master can securely fasten the door block, cut locks with loops, to aesthetically arrange adjoining and ensure the long-term operation of the doors.

Requirements for the proof and its preparation

The correct installation of the doors is not possible if the discovery does not meet the specifications. There are two aspects: dimensions and geometry, as well as the strength properties of the open end of the wall.

The dimensions are determined by the dimensions of the door block, which will be installed in them, and technological gaps, uniform for all types of interroom doors. They are as follows: 3 mm between the door and a box, 10 mm between the web and the floor, 20-30 mm between the door block and the edges of the day. It is also limited to the minimum thickness of the wall, it is 80 mm - the standard value for a simple frame partition from HCL.

The final dimensions are also dependent on the size of the bar of the bar of the door frame, called the one-old. As a rule, its thickness in the site of the subservation is 30 mm, but there are also non-standard products, especially often in import doors sets. Thus, the horizontal envelope of the opera is the width of the door leaf, which can be from 60 to 100 cm, plus two stale 30 mm, plus 6 mm of gap and at least 40 mm foam seam. The height of the proof is the length of the door leaf (200 cm standard and 190 cm for bathrooms), plus the upper gap in 3 mm, plus the lower gap, which can be 10-25 mm depending on the presence on the floor of the carpet or sealing brush on the door.

The main mounting of the door is performed by mounting glue-foam. However, for temporary fixation of the block, a mechanical fastener will be required. For this, the ends of the loan must be durable, without sweeping and changing fragments. To improve the contact properties of the foam, the opening should be abundantly moistened with water immediately before installing the door.

If the dimensions of the passage are such that the thickness of the adhesive seam will exceed 40 mm, it is necessary to reduce the lining with lining. To this end, a conventional wooden bar or a skeleton design with plasterboard is used can be used. It is important that the strength and sound insulation qualities of such a superstructure were not worse than the wall.

Build the door block

Doors are installed consistently towards the general exit. In the period of curing the foam, and this is about two hours, the door must be closed so that due to the extension it is not expelled.

Before installing the door block is collected partially or completely. Partially means to assemble the door frame, hang the cloth on the loop and install the corner brazers. With complete assembly of the unit, locks and the rest of the accessories are also cut.

You can collect three- and four-sided box. The first option is most common, because usually floor coverings are placed in a single contour. Boxes with a spawning are usually put at the entrance to the bathroom or premises for which high-quality sound insulation is important.

The ranks are collected in a straight cut box, horizontal bars are applied to the ends of the side. Upper crossbar can perform for envelope box for a couple of centimeters. With an indent from the edge of approximately the thickness of the stokee, it is necessary to cut a coating with a shallow tooth, without damping the coating on the other planes. Then it should be made by the chisel sliced \u200b\u200bfragment and align the chip flush with adjacent shelves. A distance equal to the width of the web plus 6 mm is deposited from the routing line of the roulette and the second propyl is made. The reverse side of the crossbar is processed in the manner described above.

It is necessary to attach a side-up to the cut as much as possible and drill one hole for the self-tapping screw exactly in the center of the coat. Drill better with a slight inclination so that the self-tapping screw was pulled out without the formation of the gap. When the P-shaped design is collected, the stokee align in parallel to each other and add two more screws to each angle, pre-drumped holes.

Cutting accessories

When the box is assembled, it needs to be put on the smooth floor by the entrance up and put inside the cloth. Having exhibit the upper gap, it should be attached between the door and the box a folded loop and note its position to the pencil. The loops are installed at 220-250 mm from the top and bottom of the canvas.

After that, the door is removed back and on the plates made for a pair of screws, the plates of the loops are screwed. This is done in order to carefully circle them along the contour with a sharp sectional blade, cutting up lamination. After that, the hinges twisted, and on the contour lines make a sample slightly less than the thickness of the metal plate. Professional installers use a hand mill with a conductor for this, the home master has to work with a chisel and hammer.

First, you need to beat off the china contour, installing the blade cut tool inwards in order not to unlock the edges. When folding the chisel, it is necessary to plunge a little more loop plate thickness. It is also recommended to make a few notches, breaking the cut plot to 6-8 fragments. To carefully remove the material, the chisel must be kept at the angle of sharpening the blade, cutting a thin chips. You do not need to essentially sampling, you should only often often try to try the plate, achieving its uniform shut away. When the samples are made, the loops are screwed with screws from the kit along the preloaded holes.

The locks are embedded at such a height so that their handles are on the same level with switches. First, the door housing is applied on both sides of the door and the holes are placed under the drive handle and the keyhole. Their centers should be noted taking into account the fact that the castle will shift inside the door on the thickness of the end plank.

Next, the lock is attached to the door to the door with the body outward, the end plank will be burned with a knife and the sample is performed on the same principle as when the loops are inserted. Measuring indents between the edges of the end plank and the case, you need to place a mortise pocket on the sample. The main part of the material is removed by the feathery drill. You need to center the pen so that the holes overlap each other by a third of the diameter, the drill must be kept strictly perpendicular to the end. After that, it is necessary to cut the remaining partitions with a wide chisel.

The mortise pocket may be a little more, it is only important to leave enough body for fastening decorative pens. Drilling holes under the lock of the lock and the larch, you should insert the lock case in your pocket, consolidate the end bar and install the handles with decorative linings. At the end of the installation, a retaliatory bar is screwed under the latch, it must be put in this position so that the closed door does not have a backlash.

Installation of the door block

When the box is fully assembled, on the side, back opening, brazers are attached at its corners. It is necessary to do this after careful reconciliation of the perpendicularity of the stoys. If the box is three-sided, bottom of the canvas should be screwed down the spacer rail. Although the traces from the attachment will subsequently close with platbands, they are better shifted to the outer side of the bar.

Immediately before installing, you need to install the canvas in the box and spread it inside, pose an incompressible lining of the desired thickness. For these purposes, LDDD or sets of plates for alignment of double-glazed windows are well suited. Before mounting from the inside of the box, you need to remove overhead fictional sides.

After installing the door block assembly in place, it is aligned vertically and the wall plane, then temporarily secured in the work. Fasteners are located in the deepening under the coating side, under the hats, it is necessary to perform the crown in the tilt. After it is necessary to close the door, set remote lining under the web with a step of 30-40 cm, then you can start filling the foam seam.

Mounting adhesive-foam has a not a greater degree of expansion as thermal insulation, which is used when mounting windows and inlet doors. Therefore, seams should be filled completely. First, a hermetic circuit is formed on the one hand, 5-7 minutes is given to the initial curing of the foam, then the remaining space is filled from the reverse side.

Inserting adjoins: Suns and platbands

The next day after installation, when the foam finally hardened, its residues are cut by the mounting knife flush with the door frame. From the side, reverse opening, you also need to clean the small groove on the back of the stoken.

If the wall thickness exceeds the size of the box, slopes are formed on the inside of the door. It is most properly used for this good for interior doors in the color of the canvas coating. The decorative design of interior doors should be carried out only when the floor covering is laid and the walls are completed. There are two ways to install slopes:

1. You can pre-shock the slopes, observing their required dawn. At the same time, after the grout, it is necessary to carefully cleaned the installation groove of the challenge. After drying the plaster, it is ground and glued the MDF panel to liquid nails.
2. If the cavity under the panel is small, dobors can be mounted on the mounting adhesive foam.

In both cases, you need to be able to properly cut the dobors and pre-prepare the struts, which are installed every 30-35 cm closer to the outer edge of the slopes. The slopes panel are installed in the same position as the current boxes: the top covers the side. First, the upper good is cut off longitudinally, driving into the desired width, taking into account the curvature of the installation of the door block relative to the wall plane. The line of the cut should be located on the door side to hide in the sinus. Then the edges then cut the edges so that in a wide part of the planka closely stood in the opening.

By temporarily fixing the upper panel, you need to remove the sizes of the side. First, a longitudinal cutter is done to become a flush edge with a wall plane, then the part must be drunk in length. At the bottom of the panel, the panel is trimmed at a right angle for a dense adjoining to the floor coating. In the upper part, the oblique subsidement is made, for this, height is measured in two places: close to the side and on the outer corner of the slope.

The glue or foam must be applied by a thin flagery along the outer edge of the sore and a sufficient thick layer, retreating from the edge of about 2/3 widths. The meaning is that the thick clot of glue formed the lever support: pressed on the outer edge of the panel, it provides its tight pressed to the side of the mounting groove. The installation of the good is carried out in this order: first the top panel is glued, which is supported by two side. After that, 4-5 horizontal struts are inserted into the opening, so that the dobors are tightly glued along the edges.

The platbands are best attached to mounting nails, inflicting glue harness along the edges. To fix the lining, you can press them for 3-5 minutes, or use clamps, after removing the door. There are certain subtleties in trimming cylinders. They should be installed with an indent of 2-3 mm from the angular edge of the challenge or rounding of the good.

There are two types of platbands: with a straight and rounded profile. In the latter case, the edges are killed under 45 ° in the stouch. When installing direct platbands, the side strips are first mounted, which should be 2 mm in height over the crossbar. Horizontal platband should be trimmed under 45 ° on the plane and glue between vertical overlays. The glue, you can immediately remove with a wet cloth or tip after drying with a rigid sponge.

Video on the topic

Purchased the door of the new design and the owner looks in bewilderment on the canvas without accessories, the necessary inserts.

If there is a desire to do without masters, so that the assembly of the door frame will be successful with their own hands, you need to familiarize yourself with this technological.

Only the correct installation of the door design will respond for its reliability and beauty. From determining the dimensions of the doorway, the competent assembly of the necessary elements depends on how long the door will be effectively the door in the house.

Important moments for which masters pay, before proceeding to working moments:

• compliance with horizontal and vertical axes of a box with walls and canvas elements
• given the condition of the microclimate in the home
• guests are observed
• pick details for fixation in accordance with the construction of the structure
• the product is fixed in the right relationship with carrying elements with appropriate reliability.
• pay attention to the use of mounting foam, its ability to expand at the time of frozen

Fixing the box for the door occurs in the following schemes:

• with the execution of marbles at a right angle, which is performed by a saw, decorated with small teeth, with special accuracy for this you need to possess knowledge and ability to process wooden parts
• installation at an angle of 45 degrees. Conduct with the use of the end saw and stub

To carry out installation actions, you need to know where the door frame assembly begins, the step-by-step instruction explains the list of the necessary configuration of commercial products.

The need for tools and materials

The acquisition of the necessary parts contains the following items:

• door canvas
• self-timers and dowels
• brucks for vertical and horizontal
• mainfish
• anchor bolts
• iron suspension planks
• kliniev in accordance with the widths of the openings
• mounting foam

The design of the door frame is an ordinary frame from vertical jackets of loop and pretended. For looped bars marked the purpose, carry loads from the canvas. In addition, there are horizontal box jumpers. The upper elements are called squeezes, bottom - thresholds.

Not every consumer mounts thresholds in its doors, as they are not mandatory and serve to hide the gaps or get rid of the draft, and also protect the neighboring room from the penetration of humidity. If a hole is formed near the floor and the threshold hides its flooring. On the side of the door box at the time of construction of the new house, they are performed before the installation of finishing materials of the lower.

The presence of detailed connections

Despite the structural simplicity of the frame at the door, their correct operation depends on the competent assembly of compounds of individual parts to obtain a single closed circuit if there is no lower jumper.

At the same time, the bars are fixed with the following methods:

• Ship connection - a durable, but time-consuming process. To perform it, they will need special skills and certain tools.
• Bagent fastening performs actions using studs, screws, you will need a detailed trimming under an angle of 45 degrees. At the same time, if an assembly of a door frame is performed from MDF, it is possible to build materials and the inaccurability of external seams.

The compounds with direct angles implies the need to cut the fourth part of the design, but is proven in practice that the method is the most reliable, simple and effective, for any door structures.

How to assemble a box

Beginners Masters choose the easiest way, connect the parts under right angles. To proceed with the procedure, you need to collect all the structural elements on the horizontal site. Suitable with a floor surface or shifted by any girlfriend.

The technological process consists of the following workflow:

• Enclosed the bars to the facial display, align the door plane with a future box. In independence, from the selected compound, elements consist of a looped, preliminary jamb and a sponge part.
• The crossbar belonging to the spill frame if its installation occurs in the opening of the foam concrete or brick should be largely greater than the box, this increases the bearing capacity. Then determine in which places to mount the shoals to the pendant. From the middle of the spill bar measured equal on both sides.
• They form the same gaps between the box and the door of the door on all sides using various gaskets.
• If necessary, are determined with dots for saws.
• Conduct the manufacture of the crossbar.
• A seer or scalpel mark a preliminary profile plot for further removal it to form an area for connecting points. Marks spend neat sleep or cuts.

Installation actions are carried out with special attention. The admission of minor errors in the sizes of BRUSEV will mask other elements, it is not east creative at the preliminary sites. The formation of surplus can be removed using the chisel, if you pin down properly.

The following assembly stage consists of actions:

• The slices of bars prepared with the necessary markers lay out where the gaps are designated on the canvas. Mark the places to which loops will be located. If the standard is selected, the upper gap is attached to this size and the point is determined equal to a distance of 2.03 m from the crossing of the jacket with proloce.
• Looped flaps are covered with screws to the appropriate bar, mark with a sharp item, along which the material removes and traces at points will be removed, the mounting holes will be drilled there. According to predetermined measurements and markups, selective actions are carried out on the bar. The recess should be equal to the thickness of the looping element.
• After the molds for looped flaps are formed, they are placed on the prepared deepening and fasten with screws.
• The verification of the correctness of all the fasteners carried out is completed, the element of the crossbar with racks is fixed.

Only the accuracy of measurements, checking the level for compliance with all parts, literacy of their fixation without distortion, will provide the opportunity for good work all.

Making Frames from MDF

Many consumers leave their choice on the installation of door frames made of composites, which are based on pressed fibers. The technological process of such a design is characterized by some points in relation to alternative options.

The characteristic of such commercial products belongs to the following points:

• The basis of the products includes elements made with cellulose fibers compressable and impregnated with glue. Ensuring strength and density occurs with special technological processes.
• All items are performed with the attachment of the forms, so that they are tightly adjacent to the door canvases.
• The surfaces of the parts are made with a decorative coating of them protect them from wet penetration and attaching the appearance of the appearance.

Various designs are divided into the following:

• With the application of paper segments. Profiled fragments are produced with texture paper and varnishing coating on them. Such products, even with a protective layer, does not protect products from defects after friction or wetting.
• Details are laminated, such products are most in demand in the construction markets. They are distinguished by the attractiveness of appearance and long exploitation. The decoration with the help of the film gives the surface-resistance surfaces and retains color.
• The finish occurs with natural wooden veneer. These boxes are similar to the manufacture of arrays, differ only to a short service life, as in a wet environment or temperature changes, the glued is disclosed.

In practice, there are examples when when assembling details, there is a compound of a wooden bar with the fastening of the stamped profile part.

Advantages of press

The choice of many owners of doors and boxes from MDF is due to the following advantages:

• rendering not large loading effects on the bearing elements due to the ease of materials
• products are made with a homogeneous structure, which causes their integrity, besides, the stability of the fasteners is noticed.
• development of technological processes in the decoration area produces production with imitation of expensive natural finishes

The minuses of cheap panels include:

• weak stability from direct contacts with water, swelling and deformation of geometric parameters occurs
• changing the forms leads to the installation of a thin door frame and heavy door leaf
• requires a careful relationship regarding mechanical damage
• installation contains time-consuming procedures

If you compare MDF and wooden boxes, of course, natural material takes the championship from all sides.

Even having lost over time, the entire primordial appearance is easy to return with the help of repair and restoration. But consumers often in the first place are their solvency.

The materials and tools for work for work are not different from the above proposed list except the MDF elements themselves. The main condition for assembling education as a result of a rectangle.

Working should occur on a flat surface on which:

• laying door web
• side sites have parts of vertical risers
• conduct pruning billets, adjusting the height with the corresponding 3mm. Gaps from above and at the bottom, if the threshold is provided
• the jumper is also cut in accordance with the width and side gaps

Then go to the connecting actions of the jumper and vertical riser. As soon as the completion of the assembly occurs, it is necessary to check whether the structural skew did not happen.

How to install a frame in the opening

The frame for doors collected from any material will remain properly inserted into the opening designed for, so that it performed its functions for a long time without creak and jamming.

To do this, it is necessary to work as follows:

• Move the assembled structure with caution to the laid place and conduct a temporary fixation of foam or packaging cardboard. The level is carried out reconcile the vertical surface of the surface to the side where the hinge attachment will be carried out. It is necessary to carry out the strength of the structure so as not to confuse the installation of the installation, so fixation is inserted into amusement places with wedges. They are made of wood waste.
• The installation for such a fix is \u200b\u200bcarried out from the bottom of the looped arrangement, there will be fasteners with dowels or. Cheing clogged over the upper corners, achieve a stable position of the entire frame. The spacer wedges are driven on each side one by one, try to combine them with each other cut-off parts. With one of the sides, the installation of a problem is carried out, the other is performed with an equalization of the door frame with a wall surface.
• The mounting of the door frame passes with the help of holes prepared under the fasteners to install the loop. There must be a compulsive to be present, so that the deformation moments do not occur at the time of screwing the screws. In this case, the feigned side is slightly fixed, do not bring to the final stage. In order not to bring down the size of this part, this part occurs after the door leaf will be installed.
• For stability, they make foam to the places of gaps.
• Take the installation of the entire door fittings.
• We put under the web laying and screw alternately loop parts, you need to start on top.

After completion, the door is completely closed using the struts, finish the installation on the installation of the preliminary part. After that, begin to apply foam around the perimeter of the whole. Experts recommend using spacer stakes, only they will provide reliable stability and exclude skewers.

It should not be increased by the number of fasteners, since the door canvas acts with its load with the help of loops, so the focus is on these places.

Extra hardware can create visibility of unnecessary holes and only under the loop base fastener will reliably hold, which must be fastened to firmly. It is impossible unreliable screwing to hide with a foam, it is not able to get rid of the problem.

Door installation with their own hands is presented on video:

Buying a new door, you need to think about the process of its installation. You can invite specialists, but if you want to save a maximum, you can always make installation with your own hands. Let's talk about the specifics of such work in detail.

Installation of the door frame is a responsible stage. The work of the entire door block depends on the proper installation.

Special attention requires installing the door frame. From this depend on the operational properties of any door. Consider different options for installing the box, taking into account the package of the door block and the material used for the production.

To install the door block successfully, you need to thoroughly think through, measure, select. Examine the opening, which is planning to close the beautiful facade. In the old rooms of the walls and openings do not have perfect lines. This can be said about new homes. Measure measurements should be thorough on all sides.

The correct selection of the door frame and the canvas depends on the accuracy of measurements.

If the door is not made according to individual sizes, you must select a ready-made option that has certain standards. After performing measurements, it can be understood what to do with a doorway, which should not be very different in dimensions from the standard canvase. For example, with a portal width of 900 mm, it is possible to 800. The remaining millimeters will be required for the door frame, technological gaps.

Determining the size of the product, choose the package of doors. On racks of construction stores you can find three types of set:

• single canvas - you need to purchase the door frame yourself (usually it is a wooden bar without decorative trim), loops, castle, dough, platbands;
• the canvas with the door frame from the same material (array, MDF) can be equipped with platbands;
• a complete set of the door block in the form assembled in the formation - the installation requires only forces and helpers to put the door in the level.

The choice of product depends on the consumer. The longest and difficult way to install the box is to purchase the first version of the door when all the block elements need to be bought and assemble yourself. Therefore, we will dwell on this embodiment. Having studied our instructions, you can install any door without attracting unauthorized persons.

Installing the door frame from the first to the last step

Suppose that the walls of the doorway are already prepared for installation work, the doors are selected according to the size of the opening. For clarity of the process, a separate canvas and a bar for the box are selected.

Installation of the door frame passes in several stages, starting with the preparation of tools and dipping unnecessary length from the boxes of the box.

Prepare a place to locate all the necessary elements. To do this, a smooth floor is fitted with a cardboard or a loaf.

For installation, prepare the following items:

• canvas;
• bar - 3 pcs.;
• dOOR, if the wall is wider than the door box;
• platbands;
• loops - 2 pcs. (for interior door), 3 pcs. (for entrance);
• lock;
• self-tapping screw;
• dowels;
• electroly saw or hacksaw with small teeth;
• stuslo, square, roulette;
• drill with different nozzles and drills;
• screwdriver with nozzles;
• hammer or kiyanka;
• any construction level;
• mounting foam with or without a gun;
• malyary Scotch, so as not to stain the surface or fasten some elements.

We listed everything in general. Now consider the stages to install the door box.

Preparation of elements

1. Unpack the door leaf, the door box elements (if they are included).
2. Inspect the product and fittings for a complete set and no marriage. After installation, return the defective door will not work.
3. Door leaf remove to the side, it will be needed later.
4. Spread on the floor bar for the box. If the parts for the frame are bought separately, they must be adjusted under the size of the web and the opening.

From this, the process of assembling the box begins. There are several ways to build vertical and horizontal stands of the door frame:

Assembly in groove

Such a method provides for the connection of the elements of the brass. A certain groove must be made in the vertical bar, which allows you to connect the vertical bar from the horizontal flush.

One way to install the door frame is the assembly of elements in the groove.

Many factory models provide for such an assembly option. With your own hands, you can also make a groove if the racks are collected from the construction bar, and not MDF billets.

To begin with, we will make measurements to cut parts to the desired length. We free the doorway at several points. As a basis, we take a smaller result, not forgetting to leave the distance for the mounting foam. It is necessary to know the dimensions of the door canvase, adding the gaps on the free door of the door in the box. It is enough 3-5 mm on each side. As a basis, take the door web with a width of 800 mm and a height of 2000 mm. Door box should have the following dimensions:

• for the door with the threshold - 806x2006 mm;
• without a threshold, we take into account the greater gap for opening the web - 806x2010 mm.

With the threshold, the door to the bathroom and the toilet are usually installed.

Installing the interior door with the threshold is required only for the bathroom and toilet.

The remaining openings do not require the threshold so that the movement was without obstacles.

How to correct the measurements of the opening, calculate the size of the vertical and horizontal bar can be viewed in the video of the plot submitted at the end of the article.

1. In the upper part of the vertical racks, we make a notch for installing a horizontal plank, which must be up with a moss. The length of the horizontal strip is calculated with the thickness of the timber and the excavation in it. If the width of the entire box should be 806 mm, the horizontal bar will be smaller. Suppose that the timber has a thickness of 30 mm. In each rack we will make a groove of 10 mm. So, 806-20 \u003d 786 mm - the length of the horizontal bar installed in the groove.
2. We celebrate the size of the groove on the vertical boards of the box, making an indent of 10 mm from the outer edge and 30 mm from the top end.
3. Gently remove the marked part of the bar. In the same way, acting with the second counter.
4. Check the connection of the elements and the size matching.
5. We connect the elements with self-draws, drilled the pre-hole drill.

The first way to build the door box on this is completed.

The second method of assembling the elements of the door frame.

This method has a slight difference in the marking of the racks.

1. Measurements are carried out in the same method as in the above-described version of the box assembly in the groove. Difference only in the length of the horizontal bar. It should be on the whole width, that is, 806 mm, because the edges will be roasted under 45 degrees.
2. After the timber is drunk on the desired length, it is necessary to make a pressure under the desired angle. To do this, take the stub, which will become a template. If there is no such tool, make a wrote on the eye.
3. We connect the elements with self-draws, driving them inside at an angle of 45 degrees.
4. Check out the size match again.

Perhaps this is the easiest way of the door box.

Build the box at an angle of 90 degrees is the easiest and most affordable way to build the box with your own hands.

For self-installation, it will suit the best options. There is no special skill and special tools.

1. Only the horizontal bar must be cut off a slightly smaller size, given the thickness of the vertical racks. In our case, it is 60 mm, i.e. 806-60 \u003d 746 mm.
2. Connect all the elements with each other with the help of screws. Use two pieces for each side. Do not forget to drill holes so that the bar does not crack. Self-tapping caps. Drink inside the bar.

Choose any way of assembling the door frame.

• install only boxes in the opening, and then hanging the canvas;
• installing the entire set assembly.

Usually use the second option, because to hang the canvas after mounting the box in the opening is quite difficult and under the power to specialists.

Installation of fittings and door leaf in the box

It is necessary to screw the loop to the collected frame. The loops can be different, but despite this, the installation of the loop is not very different:

1. We make markup on the vertical rack, given the side of the doorway opening. From the top edge, step by 200 mm and attach the loop bar to the bruus. Pencil circle the contour by which we will make a remission for fixing the loop. Make the same markup for the bottom loop.
2. With the help of the chisels, chisels and hammer, remove the extra part of the wood to get the necessary groove.
3. Scriminate the loop, if everything is fine, secure it into the landing place.
4. The same manipulations have done with the web.
5. After mounting the loop, we lay the cloth inside the door frame.
6. We check the presence of the necessary gaps, put the cardboard so that the web does not move during the installation of the block in the opening.

The most responsible moment occurs - installing a set in the doorway.

Install the box in the doorway

At this stage, you must call an assistant.

The installation of the box in the interroom opening is the most difficult moment. Be patient, carefully, neat.

The door block is sufficiently heavy, and work must be done with maximum accuracy.

1. Raise the product to the vertical position and move to the way.
2. Install in the opening, shifting to the extreme point of the wall. If the width of the boxing timber is not enough to cover the entire wall, the installation of door sworses at this stage is necessary.
3. Using any convenient level, exhibit the door block in the opening. For fixing, take the wedges that, after fixing the box to the walls, you can delete.
4. Put the struts from all sides, adjusting the level of vertical and horizontal planes.
5. Making sure the door block is installed correctly, secure the box with self-draws to the wall. To do this, drill holes in vertical racks and wall. Metal box is better fixed on anchors in pre-installed dowels.
6. Fix the horizontal bar. Each rack is enough to use two self-pressing. They reliably attract the door frame to the walls.
7. Check the operation of the door cloth. It should not touch any rack.
8. Go to the cutting of the lock on the door. We have already talked about how to do this in one of our articles.
9. The last stage of the installation of the door frame with the canvas is coming - the marking of all gaps. Do not hurry to squeeze a large amount of foam. It has the character of swelling, which can lead to strain elements. Make it with small portions, moving upwards. Foam should fill all the gaps, providing thermal and noise isolation of any door. Before starting the foam, close the racks of the box with molar scotch, so as not to damage the surface.
10. After drying, remove the foam spoken knife.
11. It remains to install.

Installation of the door block on this completed. You can do all the work with your own hands, because it is easy, having such a guide.

How much can you save on an independent installation of any door?

Not all manufacturers or door sellers offer free installation. The price of the installation of the door frame and the canvas sometimes reaches large indicators. On average, rates for services of specialists vary from the cost of goods and the complexity of work. The number can reach half the price of the door block. The cheapest door will be fully utilized at least 6,000 rubles. So the installation will be within 3000 rubles. We took the average for the installation of installers. The price can achieve large indicators. Therefore, saving when installing the door frame with your own hands is essential. And if not one door bought, and all? You can calculate the result yourself.

A two-dimensional door is installed similarly to a single-handed, demanding only more time and hanging two cave.

There are no difficulties. On the example of the installation, considered in our article, you can install the door frame from MDF with your own hands. It usually corresponds to the size of the selected product and the problems should not occur.

Proper assembly and installation of interroom bathing doors with their own hands is a very serious and responsible matter. Therefore, in this article, in order to assemble yourself, install and save, we will analyze the step-by-step instructions on the topic of the right assembly and the installation of interroom attempting doors with your own hands. After all, not everyone can assemble and install the box and the door correctly. A specialist call will cost you a penny, and if the house is new and you need to install more than 10 doors, so it can be broken at all.

The most common on the market, among the finished interroom doors, do the doors made from natural wood, MDF and Fiberboard.

Doors from DVP consist of a wooden frame of the laminated Lamps Lamps. This is one of the cheapest doors and the easiest. That's just the strength of such doors leaves much to be desired, and besides, they are afraid of humidity, because of which it can be "unscrewed." So if you want to put such a door in the bathroom, then it should be pretty thoroughly think.

Interior doors from MDF are more durable, resistant to moisture and have better sound insulation in relation to doors from the fiberboard, respectively, and the price of them is slightly higher. Well, as they say "for quality you need to pay."

Interior doors made of natural wood, as you probably guessed, belong to the most durable and expensive types of interroom doors. And prices for them depend on what wood they are made from.

Also they are divided into types of software.

Types of door boxes of interroom doors.

Boxes of fiberboard, as well as doors do not differ in high strength, respectively, the price is also low. Because of its fragility, heavy doors should not be hung on such boxes, such as MDF and wood. Once a box of fiberboard, the doors should be from the same material.

The door frame made of a dry raw profiled timber, respectively, much stronger than the previous ones, and the price is higher, though it needs to be finished with their own hands.

The laminated wood door frame is an analogue of the previous one, except that it no longer requires processing. However, when buying such a box, you need to pay attention to the quality of lamination, if the layer is too thin, it is more prone to physical effects, and this appearance of scratches and scratches, cracks may appear and subsequently fly away.

Preparation Before assembling and installing swinging interroom doors with their own hands.

First you need to dismantle the old interroom door, remove the old door frame and remove the poorly seated cement. If there is such a need, then align the doorway with various dry mixtures, which a huge amount is offered on the market, for example, "heat".

If, after removing the old door frame, the doorway remained too large chips, then for their alignment, you can fix the board to the slope that needs to be aligned, it will be performed as if the role of formwork, and on it and on the walls to score with the prepared solution. After the solution freezes, you can safely remove the board. It is possible to consolidate it with the same dowel-nail or struts. After alignment, you can move to putty if there is such a need.

Proper assembly and installation of interroom bathing doors with their own hands, the main steps of step by step.

The correct installation of interroom doors is usually starting from the build of the box, the installation of the loops, and already after this, we set the box in the doorway, anquerim and scatter. Install the door leaf, a diverse element, if necessary, and at the end of the installation of platbands. If the door frame with the threshold, the door must be fitted to it.

Tools and consumables for assembling the door frame and installing interroom doors do it.

Building level
Roulette, Galnik
Saw, hammer, metal hacksaw
milling cutter, chisel
Perforator
Screwdriver
Stuslo
Drills 3-4 mm and bora 4-6 mm
Screws on wood
Dowel-nails
Mounting foam
Wooden bars, wedges
Drills for concrete and wood.

Proper assembly of the door frame of the interroom swollen door do it yourself.

1. First of all, you need to choose a flat surface, it can be either the floor or a pair of tables shifted to each other, and to lay that neither be soft, and the cardboard package from the door is suitable. We put the vertical bars (stale, looping and the bee) from the doorway to the top and put the door cloth in them. Now we need to "fit" both challenges so that between them and the doorway was a clearance of 2-3 mm. To make it easier, it is possible to use pieces of cardboard for compliance with the gap, inserting them between the web and stained.

2. Now we need to cut off the sputum, upper crossbar. To do this, apply from above to our lying shelter and canvas crossbar, align "flush" with one of the stakes and mark the length. It remains to spill the bar on the mark. If you have a laminated door frame, you need to start sawing from the laminated side. If you do vice versa, you can leaf laminate and spoil the view.

3. We again apply the crossbar to the racks and the canvas, and mark the dimensions of the protrusions pretending to spill on the upper crossbar or on the stroke. For spillation, it is best formed with a metalwork for the metal, since she has a smaller teeth and thinner, thanks to this, a laminated surface will not be cleaned. Cut the best not at the mark, but next to it. During the dummy, watch not to touch the laminated surface below. When the cuts are ready, the extra ledges are neatly removed by the chisel.

4. Apply to the stroken pouring and fasten them with self-draws of two on each side. Typically, the upper spill crossbar is fixed to the steak on the screws with dimensions 4 * 75 and 4 * 50. Of course, it is initially desirable to drill holes a little less than the diameter of the screws, especially it concerns the boxes made from the fiberboard. Now we are also necessary to observe the gap in 3mm between the pouring and top of the canvas, again you can use pieces of cardboard.

5. Check the diagonal just in case and if everything is perfectly proceeding with the discharge of the stroke. They need to freeze them so that between the floor and the web was a gap of about 10 mm, it should also be a gap between the floor and the sheek 1-2 mm, to ensure the thermal expansion of the floor covering. In general, for interior doors without a threshold, it is customary to leave the gap between the floor and the web 5-10 mm, it is necessary to provide an air exchange, and the kitchen doors leave the gap of 10-15 mm. Here it is needed for a sudden gas leakage, since the gas is heavier thanks to the floor, and with a closed door with a small gap, the kitchen will quickly be filled with gas, and for its explosion it is enough to turn on the light, and with normal gap it will distribute across the apartment, so that The leak can be determined by the smell before the critical volume.

If you have a door frame with semi-circular cross sections, the rectangular connection is not suitable, since the joints will be very noticeable, in such cases the compounds are made at an angle of 45 °. To perform such connections you will need a stub.

When the assembly is made and installing door frames and interior doors with a threshold, such as inlet or in the bathrooms, the threshold is installed in the same way as the prodochin. The only difference is that after installing the upper crossbar, the costs are cut off by 3 mm longer than the door canvase to observe the gap.

Installation of loops, canopies, on the box and swinging interroom door.

Before installing the loops (samples), you must first determine where the doors will open, outward or inside, and in which direction, left or right. Accordingly, the loops choose the left and right. If you include figurative thinking, and imagine that the door opens on you on your left side, then you need a "left" loop, if the right side, then "right". The loops consist of two parts, cards, one of which is screwed to the door canvase, and the second to the box.

Where the door will open, inside the room or outward, depends on the premises where the doors are installed. If the installation of interroom doors is produced in small rooms (pantry, bathrooms, balcony, loggia), then the doors should open out, in large rooms, the doors are usually open inward.

1. Now lace a loop on the box and the door canvase. Usually, from the top of the upper loop to the edge of the canvas should be 200 mm and from the bottom loop to the edge. We take out the pieces of cartons from vertical slots between the web and racks (honey the upper crossbar and the door of the cardboard do not touch), we move the cloth to the side where the castle will be. Inserted loops inserted into the increased gap, and mark them with a pencil location. For the convenience of work, the openness can be carefully made up with a wooden plank, Bru.

2. After the markup, we take out the canvas from the box, put carefully on the edge, we apply the hinges to the places marked and the pencil we supply them along the contour.

3. Then you need to make a sample for sampling with a thickness of one map of the hitch, well sharpened by a chisel or cutter. Since the sample under the loop in the future correction is not subject to, then you need to work carefully. Working with the chisel, first you need to walk along the contour of the future loop backing at the same time 1-2 mm inside and try not to crash deeper the thickness of the loop card. When sampling wood under carport, you need to regularly try on the map of the hitch to control the boundaries and the depth of the sample.

4. Apply the loop cards to the selected places and screw them to the door, initially drumped the hole for the self-tapping screw to the canvas not cracked. Hats for self-tapping screws should be flush.

5. Now you need to embed the loop on the stoken, for this we apply the web to the box and check the markup locations on the box, also make the sample and screw the second card (part) of the loop. Only to perform the insert in the door frame must be carefully due to the fragility of the structure, so it needs to be pretty stroved, it is not desirable to raise. You can cut a loop into an overlay box, making all the necessary measurements and markups for this or after installing the door frame in the doorway.

Many advise to install three loops on the door, the third put either in the middle or between the middle and the upper loop (hitch) about 50 cm from the top of the door leaf to reduce the load on the upper loop. Because over time, under the weight of the door leaf, the screws twisted into the upper loop, begin to break down their seats and the door saves, and various attempts to strengthen the upper loop do not help. Therefore, experienced masters recommend installing three hits at once, and then it will be complicated then the same.

If you want to simplify your work or are afraid to turn the door with a box, you can install overhead loops "Butterflies", which do not need to be inserted, but there is one but, they are not desirable to install on the door weighing more than 40 k.g., and for budget (laminated, veneered) they fit perfectly.

Installing the door frame in the opening with your own hands.

Before starting the installation, you must make sure that the doorway is clean and nothing superfluous in it. If the opening is very wide, it can be reduced by installing one or two bars in the places of installation of the stary, the width necessary to the missing size.

During installation of the door frame, you need to ensure that the upper transverse is horizontally, and the cost vertically.

The top of the box is secure with wedges on the junction of the stoken and transverse, if the opening is much wider than the door box, then you can install bars.

To secure the bottom, you will need a bar, 6 mm larger the width of the door web to comply with the clearance, it will play the role of a temporary bottom transaction, to crunch the bottom of the door frame. I exhibit the cost strictly vertically, check them with the level, put the bottom strut and cut the wedges. You can check the box diagonally.

The first crepim (dowel. Selfless, anchor) in the opening of the door frame rack with loops strictly vertically, not forgetting to slip wedges in the mounting places so that the rack is not waves and straight. The vertical is better to check the plumb, the level can lie.

Then I exhibit the top transverse horizontally and also we describe. The latter exhibit a vertically second rack.

When the door frame is exhibited and aligned with it.

Door box Breppy with dowels or anchors. If the walls are brick or concrete, then first in the strokes need to drill holes in a tree drill in places of fastening the loops, and on the opposite side, for fastening the box, drills in the site of the gun. Just in case, again check the level of the door frame and if everything is worth it as we need to put the drill on a concrete with a diameter of 4 mm and neatly through the costs. We plan the location of future holes under the dowel. After that, the door frame can be removed, we put the drill on the concrete of the already larger diameter-6 mm., We drill holes under a dowel or anchor, insert them, and then put the door frame in place.

In the resulting holes, we put screws, dowels, but you only need to drive them half. It is recommended to check the installation correctly with a level and if you need to adjust it correctly. If everything is worth it as you need to safely drive the screws or dowels until you stop. But be careful, with a strong twisting of the screws, the box can be raced so that this does not happen to use wooden wedges. Just in case, again check the doorframe level and if everything is fine, you can install the door to the place. We check for opening and closing, you also check the gaps between the doorpass and the box.

There is still a way to mount the door frame. We will need fasteners, direct suspensions for mounting profile to the wall used in working with plasterboard. You can also use them together with the method described above. It is only necessary to apply them before finishing the walls, or put the seats for them, consolidate the door frame, external from the plates to cut off and perform a finish in the fastening places.

You can be interested in articles at home and.

Instead of suspensions, you can use metal mounting corners.

And if your beauty and aesthetics are not important or you are in a hurry, you can fix the door frame simply drilled in two, three places on each side and drown the hats of self-tapping screws.

Small council. Try not to anchor into masonry seams, in them a dowel, anchor almost does not hold.

Now, with the help of a mounting foam, finally fix the door frame, prehaling it with scotch. To increase the grip of the foam with the wall, it must be moistened with water. Since the foam during drying increases in volume, it is necessary to fill in the third part of the empty space between the doorway and the box. Vertical seams need to be started to fill in the bottom. After the bounce, the door must be closed, between the box and the door insert pieces of cardboard, so that the foam does not squeeze the door frame otherwise the door may not open, or spread the door frame with spacers. For a complete drying of the foam, it is necessary to wait one day, and then it securely fix the box.

After you can delete everything too much and go to the installation of platbands.

Doorway decoration

Platbands on doors

Seam with foam between the box and the wall closed by platbands. In the corners, the platbands are connected to the "Us", with the help of a small or a stouch, they are cut at an angle of 45 degrees. Putting on the door frame with finish nails or screws with special plugs, initially drilled holes about 50-75 cm. The platbands must retreat from the edge of the door box for 10-15mm. On the thickness of the hinge compound.

Dobra in the doorway.

Since sometimes the thickness of the doorway is greater than the thickness of the door frame, the opening is separated by a good plank. Carnate the bar to the work can be a construction silicone.

If the doorway is wider than the door box and you do not want to install good things, then you can shock the opening of the opening. How to do it, you can read in the article. If the door blast from the fiberboard cannot be applied to such a finish, since the Fiberboard is afraid of moisture and can wake.

Assembly and installation of interroom doors do it yourself as you see, does not require much costs for the time, and the efforts of many people. Doors can be installed in one person, the main thing is to do everything correctly, do not rush, everything is precisely measured and everything will turn out to be worse than that of professional installers.

The complete set of the door block includes a canvas, box and loop. It is difficult to purchase a ready-made complete set. Therefore, nothing else remains how to make the door frame with your own hands from the profiled bar or entrust this task to specialists. The box, most often, have to be selected separately, and it represents a design that is not ready for installation, and several elements that need to be adjusted according to the size of the opening, make the necessary guilt and assemble. Doof the door frame is not so easy, so besides the tool, it would be nice to have at least a small joinery skill.

Wood MDF

The box serves as not only by the framework of the door flap, but also bearing the base. The strength of the entire design and its durability depends on the quality of the material and installation of the product. The choice of material depends on the purpose of the door and the material of the canvas itself. Metal-plastic and metal doors are usually supplied in full configuration, so we will consider only those cases when the manufacture of the door frame has to be performed independently. As a rule, in this case we are talking about two types of material: wood and MDF.

• Natural wood has a different density and sorted on soft and solid. The cheapest and challenge goods are pine, but if we are talking about installing entrance doors, you should navigate to a firm and expensive variety of wood, for example, oak. It will provide durability, strength and reliability of the design.
• MDF is used exclusively for interior doors. If you have to assemble the box of this material, all the cutting edges should be treated with nitroloma to ensure protection against moisture.

Complete set and standard sizes

The box for the door consists of several slats: two side, upper and lower, if a threshold is provided in the design. If the depth of the doorway exceeds the appropriate parameters of the bar, the kit must be supplemented with dogs that will increase the depth of the box.

Standard dimensions of door blocks vary in width and height. Compliance of the parameters of the door leaf, block and opening, indicated in the table.

The assembly of the door frame is performed with the following moments:

• There should be a technological gap between the inside of the box and the door of the door throughout the perimeter.
• The gap between the wall and the upper part of the box should be at least 20 mm.
• The gap between the side planks and the wall is 10 mm from each side. When installing on the mounting foam, it will need to increase the gap at least to 20 mm.
• The gap between the lower part of the sash and the box or the floor depends on the material and place of installation of the structure. For dry premises, these parameters may vary within 5-15 mm, for wet, in order to ensure ventilation, - 50 mm.

Connection options for design elements

The main complexity in the assembly of the door frames represents the process of connecting individual elements. Dostech of horizontal and vertical planks of the product can be performed in two ways:

1. Through the angle of 45 degrees. This process is better to perform a trader saw, but a stub is suitable for its insension.
2. At a right angle of 90 degrees. For cutting blanks, it will take a saw with small teeth.

Pitch slats is carried out by means of thickening compounds or galvanized screws. The figure shows the variants of thickening connections that clearly show how to assemble the door frame yourself to ensure high strength of the compounds.

When performing the calculation of the length parameters and the width of profile rails, it is necessary to consider that the length of the spike should be equal to the thickness of the box bar. A thickening compound provides sufficient strength of the finished design, but if you wish, you can make additional reinforcement of the joints with zinc coating nails.

Door Box Assembling Process

Consider how to properly assemble the door frame . As the source material, we need a profiled timber bar of natural wood or MDF.

Build the box is performed in the following order:

Phased installation process

To secure the collected frame in the opening and put the doors with your own hands, you need to perform the following activities:

Tip: Before giving, it is necessary to clean the surface from dust and moisten with water from the spray. These measures make it possible to significantly increase adhesion.

Another important condition so that in the process of installation does not disrupt the frame geometry - the use of spacer wedges, which correspond to the width of the box and are inserted across.

The final stage of the installation of the box and door is the decorative design of the opening of the swap.