The original decree in the house can be a ladder of plasterboard. This does not mean that such an important design will be collected from such a fragile material, but as a variant of the design of the interface, with which it can be made with a single element of the interior. In order to persuade the ladder of plasterboard, knowledge of safety requirements, and of course, about the technology of work.

Design and design of plasterboard stairs

As a rule, stair structures collected in the form of base from metal elements are needed in additional finishes. Full wooden options and so great fit into general repairs, but the frame can be created from the tree.
Why is the plasterboard ladder covering can be considered a good finishing option? The reasons are as follows:

1. And fasteners will cost much cheaper in comparison with other materials: metal, wood, tiles.
2. This type of finishing is quite simple to perform with your own hands, and for very short time "put into operation" the finished object.
3. Plasterboard trim on can be decorated with any ways, creating stucco, textured surface, imitation of marble and other.

   An example of a staircase of the staircase sheets of drywall

4. Using simple technologies for processing drywall, the staircase finish can be performed in the form of non-standard curvilinear figures. Moreover, in comparison with wood or metal, for such a work, it will not be necessary to have complex processing equipment, with which it is not possible to work with your own hands.
5. The strength of the mounted finish of the staircase of plasterboard with the observance of technology and the rules will not give up to the analogues.

What should be considered when working with such material, creating structures for use in specific conditions? How to shelter the staircase with your own hands by plasterboard so that it reliably serve a long time, and complied with the safety standards, and would there be original design?

Rules that need to be observed

Stair marches in a private house are used quite often by all family members.


Options for plasterboard fence on the stairs

And, except for the most aesthetic side, the practical component is very important, and the more secure. Before you have a ladder of plasterboard with your own hands, you will need to understand many rules with compliance with them:




What details can be done on plasterboard stairs so that they are durable, long-term and aesthetic:




How to start performing the finishing of such a design, and how to perform all the work from beginning to end with your own hands?

Planning and design

So, having, for example, the made base of metal or wood with steps, you need to make it a finish, you need to start with planning and accounting requirements for such structures.
In addition to the design of the safety rules, the staircase must have a fence on which the railing is mounted for ease of use.
Of course, with internal design, it is often possible to see the presence of staircases without a railing, but whether such structures depends on the owner of the house. Safe use of such a march is not guaranteed.


Drawing with dimensions of plasterboard stairs




Name of plasterboard staircase elements


Observing the requirements of the norms and rules, the height of the fence on the stairs in the house should be at least 900 millimeters. In the case of having small children in the house, their indicator is definitely 1180 mm.

If the lifting by march is carried out along the wall, it is usually one fence, but with a march width of more than 1250 mm, it is necessary to install the railing and on the other side for more convenient use.

Railing diagram for stairs




And also if the handrail is manufactured along the wall, it is placed from the plane at a distance of at least 40 mm. All these parameters are necessary to take into account before to separate the ladder of plasterboard and create a railing from it.

Materials and tools

List of materials and tools Standard:




The list of tools is as follows:

1. Drill.
2. Screwdriver.
3. Roulette.
4. Bits.
5. Drills (if necessary).
6. Spatulas.
7. Nozzle mixer.

How to finish the ladder of plasterboard?

Technology of work

So, the following elements can be built from the drywall on the staircase: the railings with fences, partitions under the march, the finishing of the span from the sides and the binder sheets below.


Scheme with sizes for mounting railing fence

Perila

Under the railing you need to build a frame, which then will be trimmed with plasterboard.

An example of the trim and decoration of rail plasterboard

Firstly, depending on the type of fence, the guide profiles are fixed to the stairs itself.

If it is metallic, you need to originally drill holes under the screws for fixation. The mounting step of the guide profile should be up to 200 mm maximum.

Secondly, the base racks are installed, which insert into guides and connect them with them.



Scheme for mounting railing to the stairs

Third, the racks are connected on top of another guide profile. Mandatory to the frame mounted crossbars. It is worth remembering that a larger number of racks and crossing will make the whole structure more rigid. If the wooden handrails are planned to be built, in the base of metal products it is worth making a bookmark from a wooden bar for mounting this element. After the assembly, the base is trimmed with plasterboard according to the standard scheme.
Look in the video: Railings for plasterboard stairs.

Finishing the stairs from the bottom and from the parties

Under such a type of registration, too, it will also be necessary for the lattice, assembled from guides and racking parts.
The bottom of the crate is done, as it is on the ceiling of the room.




Such structures are built with a side of a staircase march. If the span itself is made of wood, with even planes you can make the skin directly on the surface.

Partitions

This element on its device is no different from the assembly of the walls and. They adhere to the same algorithm, with mortgages under the door spans, and.
The walls of the walls along the staircase are also carried out according to standard technology, with the assembly of the crate of the connected with the bearing wall. Record with the same materials - and the entire surface.


Design of plasterboard and design of the staircase march and rail




Registration is made on prepared plasterboard. To do this, pre-conduct a full range of finishing works with the original sealing of the joints, and further putty. The decor of the ladder of plasterboard can be made in the overall style of the design of the room. There is nothing complicated in the manufacture of such stairs with your own hands, it is only important to plan work correctly and acquire the necessary materials.

The staircase should guarantee safe movement and harmoniously "fit" into the interior. It is necessary to protect the construction itself from premature wear, and the owners of the house rid of the need to repair the construction and discomfort during the use of them. Rationally solve the entire spectrum of tasks will allow the finishing of stairs to perform the extensive series of finishing materials. Let's discuss the choice of a cladding method and find the optimal option.

In fact, the lining of the stairs is a decorative design of existing wooden frames, metal structures or concrete marches with staircases. The final result must be combined with the optimization of operational characteristics and with the formation of comfortable conditions. An important argument that substantiates the preference of the material and the method of implementation is the question of whether the staircase can be performed with their own hands. Summing the arguments "for" and deducting all aspects with the wording "against", the owner will make a competent choice.

In the list of arguments for the selection of the material of the finish, decorative, insulation qualities, operational safety and the ability to perform their own hands

Basically, the solution of this arithmetic problem is based on three "whales", this is:

• configuration of construction;
• preferred sound insulation parameters;
• contingent users.

An important aspect of the selection of the material for finishing - the configuration of the structure, the ladder with running steps is easier and aesthetical to separate wood

Possible to independently perform the method depends on the desire of the owner to separate the staircase itself, from its diligence and availability of skills. Of course, it is necessary to take into account in the central or in the economic zone there is a staircase and the degree of presentation of the structure.

We choose finishing materials for stairs

The surfaces of concrete, metal and wooden stairs are separated in whole or in part, the combination of different materials is applicable. For example, the decoration of the concrete ladder steps can be performed by wood, and the use of nickel-plated parts, forged products, glass is quite suitable as a fence.

The facing of the concrete and metal staircase with a tree perfectly combined with glass fences

The risers and side parts of the Kosomrov can simply be painted, and shining to bore a stone and lay the plinth combined with it. The staircase of the staircase of the wear-resistant 31st class laminate, parquet layers, and any flooring is performed. Mass options, consider each of them.

Ladder carpet

Prefers the staircase with carpet families with young children, in homes where older people live, sensitive to unnecessarily ringing the noise of steps along the stone surface. Often, the central stairs of respectable organizations sweep the central stairs.

The decoration of the ladder carpet is preferred families with young children and older people, the advantages of covering no noise and pleasant tactile sensations

Elastic soft material does not need to cut, it is immediately laid. The mount is made by plastic, wooden plinths, most often brass rods that need to be fixed in the projected specific clamps. In the case of too strongly speaking, the adapter uses additional rods-rods.

To extend the terms of the carpet service under it, felt or similar material. Can be separated by carpet with any design, by crossing the folds with pins or bent needles.

Decoration of the ladder carpet: Method and fixtures for laying a roll coating on oversized steps

Linoleum, Rubber Rugs, Laminate

They are covered with them only sticking. Rubber non-slip rugs and cut-out linoleum are fixed to wooden steps with metal straps and corners. Corners are used for fastening to the long side of the sticky, the planks to the end part. To the concrete and metal surface they are simply glued with a special composition.

Planks and corners are also used for fastening the laminate. To cover the adoption, a solid plank will be needed, for the riser, the material is cut by the jigsaw on the lines marked in advance.

For facing the ladder laminate, metal corners and planks are used, the corners are installed along the long side of the sticky, instead of the end slats for fixing the material can be used by plinth

Note. At the design stage, the type and size of fences, the location of the components of the parts should be taken.

Clinker steps, tile, porcelain stoneware

Finished clinker and porcelain stagnate steps with anti-slip coating are a wonderful option produced by manufacturers for all types of structures. You can choose and acquire now a complete set for arranging the entire structure with mounted on the left or right by plinths. With the help of the finished set, the staircase finishes are very simple, if the dimensions of the structural elements correspond to the size of the products. If the sizes are inconsistent, you will have to make a screed with a concrete mixture.

The decoration of the stairs of the staircase ready-made sets of porcelain is performed easily and quickly, the surface of the steps is equipped with an anti-slip relief.

Ceramic tile will need to be cut off that far from all performers goes aesthetic. For the cladding of the screw staircase, it is not recommended at all: there will be a lot of ugly seams. Facing straight march tiles should be started from the bottom stage.

Gently beautifully bold the stairs staircase with tiles quite difficult, even even professionals are often refused to stack outdoor ceramics.

Finishing with natural stone

It is performed in the same way as the facing of the staircase tile, because used for decoration granite, marble, non-porous sandstone or basalt comes in a similar format. Cons of material in ringwater effects from steps and in value. Behind porous rocks is overlooked.

The facing of stairs with natural stone attracts operational long-term, repels the high cost, the need to hire the finishers, not all suggests the ringing of steps and the feeling of cold

Budget Solution - Paint

If it is absolutely not interested in the presentable finish of the staircase from concrete or metal, if it leads to a basement or in a different household room, it is possible to tritely paint all the components of the design with water-repellent properties. The paint will protect the material, but the steps will remain cold. From time steps, she also will not save. True, if the facing of the concrete staircase will combine dark wooden sticky with painted light paint risers, the design will become elegant and visually easier.

Staining - budget practical solution protecting material from premature wear

Ladder from lumber can be painted or coated with translucent protective and decorative enamel, transparent or tinting varnish, antiseptic impregnation with coloring matter.

An interesting variant of staining of the stairs with wooden steps on largests and a metal guide

Wood and its priorities

Light material with excellent thermal insulation and decorative qualities is easy to process, combines with all existing facing options, it works in any interior. The cladding of the concrete staircase with a tree will slightly increase the weight of the already cumbersome heavy design, will give an unspeculent construct a respectable appearance. Wood can be separated by the construction of any configuration, install beautiful fences with curly bales, use artistic threads.

Wood - Material with excellent aesthetic and thermal insulation properties, it is easily processed, slightly increases the weight of the structure

The main plus - wood will make the steps warm, on them without fears you can even be a bosaka. Because the owners of the country housing in priority the decoration with a metal staircase with a tree, because it is just as concrete does not please the owners with comfortable warmth.

Modular staircase with metallic kosoour frame with wooden steps

In such cases, on a welded metal ridge, it is installed or only a sticky, or all elements of the stage on top of the preceded moisture-resistant plywood. After facing the steps, you can see the entire design of plasterboard.

Steps of a metal staircase can be completely seen by wood or install only wooden sticky

Stepitary sheathing stairs wood

We can shelter the concrete ladder of wood will be almost two months after her fill. Concrete during this period will allocate all excess moisture so that the sawn timber installed on top of it is not diluted in the consequence and did not deform. The number and complexity of technological stages depend on the quality of the fill. The full cycle of work on the trimming of the concrete staircase will include:

• Alignment. The surface of the monolithic structure with a fair amount of flaws will need to be aligned. This uses standard methods for aligning a concrete base: screed and lag. To froze the polymer self-leveling mixture, a week or two will be required, the concrete screed will stick and lose moisture again about two months. It is better to use lags. And they are faster, and the weight of the stairs will not too increase.

Important. If it was originally planned for the cladding of a monolithic wood structure, when designing it is necessary to take into account the thickness of the finishing material. With a special care, you should consider assembling the formwork for the fill of the concrete staircase so that it does not have to fix the alignment even the difference in the size of the steps.

Facing of wood on the stage of the concrete staircase stacked over the waterproof plywood

• Laying plywood with moisture-repellent properties over a screed, lag or topped with steps cleaned and plaster. Material must be selected with a thickness of 12 mm, fasten it with a dowel-nail.
• Fastening elements of steps to plywood. It is carried out with the help of glue and screws.
• Marking installation plinth, balusters, then fasten the handrails and decorative parts of the fences.

Most often, the facing of the staircase of the tree predetermines the use of polished and processed paints of parts. However, no one forbids performing paintwork after.

Knowing the technology of the skin and finishing of stairs is necessary not only to those who decided to independently perform the work, but also those who decided to hire the finishers and chooses the optimal way of cladding. The information received will help the owner to identify violations and stop the desire of workers to save on time and on materials.

It is unlikely that you feel comfortable when the staircase in the house creaks, and the steps begged. Everyone wants her to be beautiful, durable and durable. Nowadays, the stairs comparable in size with the creations of the fathers of architecture are made from reinforced concrete or metal. The story will go about steel design, lined with wood and plasterboard

So, the welding works are completed, the metal frame of the stairs is installed in its place and covered with a layer of protective primer. It is tightly screwed below with anchor bolts to the concrete floor, freely relies on the end of the opening in the overlap. The weight of the construction reaches one and a half tons. You can temporarily put wooden fees to the place of steps for the convenience of movement and work.

Metal and wood - one

What is the advantage of steel before reinforced concrete? Modern stairs are not limited to simple geometric shapes. As a rule, they are structures with many spans and turns at various angles, part of which is a complex fence of wrought metal, hardened or special glass, wood, stone and other materials. Such stairs should have increased strength to withstand the weight of not only people moving along them carrying furniture, household appliances, but also a massive decor of fence, railings or handrails.

According to the pre-made markup, the plinth panel, which decorates the staircase from the wall side, is fixed with "liquid nails", and then screwed to the wall screws. Similarly, the panel is installed and attached to the platter from the outside of the staircase. This work is done after the decoration of the steps and installation of the landing.
The assembly of the steps are beginning with the fact that in the lower side of the adapter with the help of "liquid nails" attacks. It is connected to an emerge, on which it relies, two screws with a diameter of 6 mm through the holes drilled in the sticking of the axial line of the joint.
Apartment is installed on the metal and attached from below four screws with a diameter of 6 mm through the holes previously drilled in the metal. This looks like a compusion and riser from the end.
The plated plate is cut to the desired size with a circular saw, the ends are separated by a grinding machine. The products of the complex profile are usually made from pre-stressed reinforced concrete on house-building compounds. Try to make such a heavy and cumbersome design to the house where overlaps are already installed. Most likely, you will not work. If you make a similar staircase only from a tree, it will include massive and large-sized bearing elements and significantly limit the choice of architectural solution. The metal gives an impressive staircase with an impressive ladder and openwork.

Any technology has its own specifics. The feature of the assembly of the stairs on the metal kosoo is that when welding the carrier frame at the installation site is very difficult to ensure the necessary accuracy of the size. Therefore, careful measurement of the frame and fitting parts is required. The ideal option is to perform all the work related to the processing of metal, in the factory and installation in the span of the finished product. In this case, the facing of the carrier metal structure with a tree (on sides and from above) and plasterboard, plastic, wood, plaster (bottom) will be less laborious and better. The weight of this structure can reach several hundred kilograms, so special attention should be paid to the safety of work.

In the architecture of private houses of Russia, the late 90s received the second birth of the Modern style. Inherent lightness and the plasticity of curvilinear forms, embodied in the art of construction of stairs. The structure we will tell you, designed and manufactured by the specialists of three different companies. Metal frame welded Master of the company "Growth". The joiners of OJSC "Svetzitsa" tipped the frame of the tree and installed the handrail, modeled and stacked in Austria. Forged fence - the work of the Kuznetsov firm "Russian forging".

The handrail is hardly the most complex and time-consuming part of the stairs. Of course, you can extend the alyapic railing or assemble them from individual, fitted with each other wooden parts, as is customary in mass production. Pieces that do not have analogs joinery are created otherwise. The handrail of complex geometry is developed by computer modeling in a three-dimensional projection (3D). Then make the layout in the natural value, along which the handrail is pulled out at the factory from a wooden array. Rotary elements are manufactured and customized by pattern. Relying on such a handrail, a person feels that this thing is created for maximum convenience and is a work of art, and not just part of the protective fence.

The stove of the staircase is heavy and uncomfortable for installation, when it is fitting and installing from workers, not only physical strength is required, but also attentiveness and caution.
After mounting, the steps set the mortgage parts of the fence. For this, the necessary holes are drilled in the steps and metal koster by preliminary markup. Mortgage parts are attracted by nuts from below.
Next comes a turn of the facing of the frame of the staircase at the bottom of the plasterboard. Pre-carved sheets of sheets are attached to metal sprues-screw screws.
Plasterboard coating put sand, after stripping the surface of the surface, the skin is ground and painted with water-dispersed paint with a roller.

High art cladding

You can bind with wood and plasterboard with any metal structure, even if it has not been provided. In such cases, the necessary parts are welded to the frame and remove unnecessary. The method of fastening the cladding and its configuration is determined in each case separately.

The ideal factory conditions we mentioned are often unavailable. And if the metal structural is welded at the installation site, then be sure to be set up by the level of carrier elements of steps. It is also important to observe a certain sequence of assembly and finishing.

How is the facing attached to the metal structures? Usually use screws with mortgage parts, screw screws and "liquid nails" (glue).

What tree is preferable for the manufacture of different parts? For cladding, solid deciduous breeds are good: oak, ash, beech, maple and even birch, both moraine and natural color. The glued wood covered with several layers of durable polyester varnish "Bona" (Sweden) is suitable for coming and staircases: it does not breed and does not crack. The risers are better made from the joinery plate, the vested of the same tree of wood as a sticky. Kosomers and wall decorated with plinth panels from the massif of the same wood. From the bottom of the staircase, as a rule, we are trimmed with plasterboard, which then shovel, ground and color in accordance with the designer's recommendations.

To mortgage details in the steps you need to install a forged fence sections. The sections are then welded together, welding places are hidden by decorative reinforcement.
Finally, the handrail is mounted. It is placed on the steel bus of the fence and across the available holes screwed into it with screws.
Part of the handrail in the place of rotation of the railing at 180 is a separately manufactured transitional element, the billet of which is made with a large allowance in length. For accurate docking with a continuation of the handrail, a cardboard pattern is made.
A thoroughly placed transition element is dug manually, the end is aligned with a grinding machine. The handrail of the next staircase is set to the transition element. The design of the steps, the shape of the grooves, the installation site of the sewage and mortgage parts may be different, they are defined both with project documentation and specific circumstances when assembling. At the factory, wooden sticky and risers are made with an allowance for the subsequent fit of the wall. When installing on the frame, the adjacent detail is customized. After a thorough obstinate measurement and risers are placed taking into account the irregularities of the plaster walls and inaccuracies made in the process of welding and mounting the metal structures, after which they pump up to the necessary sizes with circular saw. The ends are grinding. The staircase is a massive wooden slab, the dimensions of which (in our case, 130 130 cm) are determined by the march width. Like the workpieces of the steps, it is made with a big bunch. The installation of the site is time consuming and at the same time a responsible operation that requires an accurate fit to the wall, and to the metal structures. The fence is fixed to the metal frame, and not to the wooden facing. The connection of parts of the fence and the rower can be mechanical (screw, clamp), welded or adhesive. In this case, a forged fence is set to mortgage parts, screwed to the Kosomers. The staircase, designed and built in all the rules of architecture, is an expensive and complex structure, the creation of which is under the power of qualified specialists. In this statement there is no dismissive attitude towards lovers to build a house with their own hands. Try it, it is possible that you will succeed.

For facing and final finishing, the ladder will need the following tools and materials: circular saw, drill, screwdriver, grinding machine, rubber hammer-mall, level, spatula, brush and roller, and screws, screw screws, dowels, silicone sealant, glue " Liquid nails ", putty on a tree, putty for sealing slots in plasterboard compounds, water-dispersive paint.

The sheathing of the stairs is carried out by various materials. All necessary for this action can be easily held with your own hands. Finishing works will help you give your home aesthetic appearance and beauty that previously used the type of metal stairs.

The decoration of the metal staircase is possible by various materials. In this situation, you can sneak:

• tree. The best breeds here will be oak or ash. Just remember that the tree in front of the trim should be treated with a special solution that prevents the appearance of its processes in the wood;

Tree casing Finishing plasterboard

• plasterboard. This is the most popular option, which is most often used to finish the staircase made of metal. With such material, you can construct any functional or decorative elements. Most often they are made from the bottom of the stairs;

• mDF plates. The finishing of the metal staircase is also quite common. But it will have a simpler view compared to plasterboard.

These three material are found as finishing material most often. However, sometimes the staircase is carried out with plastic panels. But they are less durable and damaged easier than the above materials.

Advantages of using drywall

Plasterboard sheets today are used most often for finishing work with their own hands. This is due to the fact that such a material has a number of features and advantages that the tree and MDF do not have.
The advantages of covering plasterboard include:

• environmental friendliness;
• high strength;
• easy and fast installation;
• the ability to create the most original and unique designs;
• the possibility of the external trim of plasterboard with various materials - paint, plaster stucco, wallpapers, etc.

Plus, such a casing will cost much cheaper than the use of wood and will have a more beautiful appearance than using MDF.

Choose design

With railing and steps

The staircase in the house may not only be a purely functional element, but also act as some decoration of the room. Therefore, when choosing the design of its design, it is worth considering all the nuances to strip it as high quality and more beautiful.
Note! Properly chosen finish of the staircase will help you hide all the drawbacks that have it.
To date, there are the following options for designing stairs:

• design with steps and railings;

• design without railing.

Without railing

Depending on the initial device of the stairs, its finish is possible as follows:

• with storage area under steps. A more functional solution, as in such a storage room you can store many different things necessary in everyday life. Such a device is possible only when the staircase is stretched;

With storage room Without pantry

• without pantry. Simple design option. The design here is impossible to design here, since such ladders have a swirling device, where each round is located above the previous one.

Also, instead of the storeroom under steps, it is possible to make a decorative niche, which will give it a more refined species.
As you can see, there are several options for design solutions for stairs. And each of them has its own characteristics and functionality. Therefore, before choosing a type of design, calculate all the minutes and pluses of the selected design.

Black

After selecting the type of design and material of the trim, it is necessary to evaluate all the nuances of the upcoming work with the help of the drawing. This is a very important stage that will allow you to think over all the details with maximum accuracy and qualitatively cope with the upcoming process.
To develop the drawing, you must do the following calculations:

Drawing of stairs

• measure the length that the design occupies and its height;
• it is necessary to measure the widths of the steps and the distance between them;
• we are determined with the railing height. For an adult, they can have a height of about 1 meter. But the villages in the house have children, then the railing must be equipped with additional protective elements that are located in the vertical plane. Here you need to determine the step between these elements so that children cannot fall into the space between them.

All these calculations display on the scale of the paper sheet, and you will have a drawing.
Next, you need to apply the elements of the sheathing and places of fasteners. So it will be clear how many materials you need, and also you have a clear plan for further action.

Choose tools

To strover the staircase with your own hands from the toolkit you will need:

• screwdriver or drill with a set of drills;
• building level;
• roulette, ordinary pencil and marker;
• corners;
• plumbes and ruler;
• fliselin;
• set of spatulas;
• scissors for metal and a knife for working with plasterboard.

In the event of a shortage of some kind of tool, it can always be asked for friends, neighbors or bought in a construction store.
From the list of materials you must be at hand;

• plasterboard sheets or other finishing material;
• metal profile. Wooden rails can be used to create a frame;
• fasteners - self-tapping screws, dowels, screws;
• serpenta;
• putty;
• primer.

After preparing the necessary materials and tools, you can start finishing the stairs.

Started faster - finished earlier

The decoration of stairs by plasterboard or with any other material with its own hands consists of two main stages:

• arrangement of the ladder itself;
• construction of balustrade.

Each of these stages will consider in more detail.

Start of registration

The staircase itself is a very scrupulous process requiring concentration and close attention. The instruction below will help you effectively and qualitatively cope with the necessary scope of work.
To shelter the staircase, you need to make action on the assembly and trim.

Frame stairs

Note! Without a frame, the decoration of the ladder design with plasterboard sheets will be impossible.

This requires such manipulations:

• first from the bottom of the stairs, on the floor, we make the markup under the profile;
• on the markup line, we set the starting profile throughout the perimeter. The step of attachment of the dowels here is 10-15 cm;
• when the perimeter is decorated, we start to display the frame in height. To do this, in the starting profile insert the racks;
• each rack profile must match the level of either the steps or balustrades;
• between themselves, rack profiles should also be made on longitudinal jumpers. This will increase the stiffness of the design and make it more durable.

Note! The frame must contain the foundations for all planned items: balustrades, niches, storage rooms, etc.

After the construction of the frame, it is necessary to sheathe the sheets of plasterboard. Here, the finish is carried out as follows:

• cut the sheets to the desired dimensions. Since the staircase has multi-level elements, it will have to cut a lot. Scroll very carefully so as not to damage sheets;
• pieces of sheets should be exactly fitted under the framework parameters in each particular place;
• the casing begins with the most voluminous and large pieces. Therefore, you need to follow from top to bottom. Usually the lowest pieces are attached from below;
• plasterboard attached to profiles with self-draws in 10-15 cm increments.

Sheetting sheets

Try to sow the design so that the slots between the sheets are absent. They must most close up to each other as much as much as possible.
After the staircase was trimmed, proceed to the formation of balustrades.

Construct balustrade

Balustrade is not only a decorative decoration of the stairs, but also serves as an element of security, especially for children. It is usually designed only from the side that is addressed towards the observer. You can simply separate the part to the second of your favorite material.

Balustrade on the stairs

The installation of such an element is also determined by the fact that the design is worth the design, which interior is also available. Therefore, in some situations, the balustrade can not be done.
In the absence of balustrades, the corners of the design are closed by a perforated corner.

The final stage

After all the above-described actions have been completed, we set the perilla and carry out the final finish:

• on the joints of the plates with glue sickle, and the corners are processed by phlizelin;
• all the places of stoves and screwing the screws are applied;
• we clean all the irregularities and the stuffing structure.

Now you can give a staircase, covered with your own hands, the final appearance. It is most often painted with dark or bright colors of paint, depending on the color gamut of the interior, or are separated by a tree and artificial stone. You can also use gypsum stucco.
Following the above instructions, the decoration of the stairs will pass quickly, efficiently and efficiently. It will be able to become a real treasure of your interior, and the result will satisfy you by 100 percent. And all this will be possible thanks to the unique properties of drywall, perfectly suitable for decoration.

http://gipsportal.ru/montazh-i-svojstva/kak-obshit-lestnitsu-gipsokartonom.htmlHow to shelter the ladder plasterboard do it yourselfhttp://gipsportal.ru/wp-content/uploads/2016/03/the-staircase-in-the-house-500 cell376.jpghttp://gipsportal.ru/wp-content/uploads/2016/03/the-staircase-in-the-house-150 Ч150.jpgAlexeiInstallation and propertiesIn the country and private houses, especially two-storey, you can almost always meet the staircase. Often it is made of metal and has a not quite attractive appearance. In addition, this design is not very safe. Especially this issue is very relevant if there are small children in the house. Therefore, many owners decide to sheathe.
Ladder clamping ...Alexei [Email Protected] Editor Gipsportal

The ceiling in the kitchen was made by an eyelace (roof raids) and was required using a plasterboard design to align it. But if you do it quite flat and align on the lower tier, it would significantly sank, therefore I decided that the best way to mount a low-end ceiling is a stepped method. A stepped ceiling gradually aligns the surface, not sharply and does not steal extra centimeters. In this article, I will tell you how the stepped ceiling of plasterboard is mounted in your own hands in the kitchen and subsequently decorated with Venetian plaster under the blue sky with clouds.

This is how the ceiling looks until editing.

First, the ceiling with foamed polyethylene is insulated, strengthened it on the tapping screw straight to the ceiling. The surface is wooden, so it did not have to drill.

Further from metal profiles is mounted a frame under the steps on the ceiling, separated by the ceiling into three parts and the frame is collected at each part of the previous one. Thus, the ceiling is flat, but steps.

When the design was ready, the hidden backlight is performed under the dot luminaires around the perimeter and the switch is displayed for them.

Well, then follows monotonous work on spatlement and grouting the entire ceiling. For angles, the grid is used to mask the seams on the drywall, also fastened it and on the joints. You can use perforated corners for corners. As a result, this ceiling turned out.