Stand for the toilet to increase height. Raise the toilet above above the floor: variations variants, a description of the process as easier to raise the toilet above

You are here now - Home - All about repair:

How to install the toilet?

In fact, there is nothing easier when installing one toilet, then it will be easier! You can already make money on it. (Joke).

How to install the toilet on the wooden floor, see in the very bottom.

To install the toilet on the floor from the tile (tile), you need:

Perforator.
Drill a 6mm winner, or 8mm. (or other diameter, it needs to be clarified by the seller, what diameter are in the set of dowels)
Dowel. (If you do not go in the kit, we specify by the seller. Depending on the holes, at the base of the toilet or 2, or 4.)
Corrugation. (In the event that the floor level has changed, or you want to slide a little to the toilet in one direction or the other.)
Level. (How to verify the correctness of the level reading?)
Depending on the situation: PCS or Selikon.

Corrugation, to connect the drain to the toilet.

We already have a tile on the floor in the toilet.
Now we need to put the toilet.
If you have a tile in terms of level, the toilet will rise by level, without the level. If not, we will have to align the toilet in terms of level. We put the level along, then across.

In order to raise the toilet from any side, use pieces of fiberboard.
- Fiberglass thickness 5mm. Therefore, for alignment - Fiberboard is excellent material.
  If, for some reason, it turned out that the lumen between the tiles and the toilet was the big and the toilet is in an incomprehensible suspended state, then you will need PCS (sand-cement mixture, it is sold at 5kg, I think that this is quite enough for you. )

Drag the PCS to the state of thick sour cream.
- How to understand what divided right? We make a slide from the solution. It should not spread within a minute. The solution should keep shape, but after that a slide must slowly lose the shape. Such a consistency of the solution is needed in order to when you put a solution under the toilet, it should fill the niche under the base of the toilet bowl. After the solution is grabbed, the toilet will stand rigidly.

First step, you need to collect everything and connect the plums of toilet bowl. If, everything fell into place, then start drilling.
- It is sometimes very difficult to note the place where you need to drill holes for dowels. Or the hole is small, or on the tile it is impossible to draw any way. You need to take a couple of A4 leaves and put under the place where the holes will be. In order for the paper does not run away, ... secure it with a scotch. On paper can be drawn by anything. If the pen or pencil does not break into the dowel hole, then take the purified stale from the pencil and mark.

Now drill.
- It is very difficult to drill tiles. The drill can not catch. To do this, use the tile drill, it with an acute end and drill easily. Just do not hurry! So that the drill does not finish very quickly, pour water into some cup and periodically lower the drill there to cool it. Do not bring it to a state when the drill will be hiped. This will lead to a rapid drill failure.

Of course, you can drill the usual drill for the perforator.
- I do it, but it will take more time and experience here. In order for drilling clinking behind the tile, it is necessary to make a mark in the marked place, as is done in the core on the metal. Just be careful. Tile is not metal and can crack.
  When the place is ready - drills. We put the perforator into the drill mode. (Without a bump.) Slowly, do not rush, and everything will work out!

We celebrate the root of the reasancement of the toilet.
- Now we remove the toilet. If the toilet is not adjacent to the base very much, use the PCS (described above.) If the toilet is adjacent to the tile, then you need a bactericidal settlement. Do not regret and apply on the contour of the base of the toilet. We put carefully toilet, plug.
  Either Selikon, or a solution of PCS, which will be released from under the base of the toilet, remove the cloth.

What other role is played by PCS and Selikon.
- In the case of water to the toilet, the process of the tuning can begin, or there may begin mold. Neither, nor the other we do not need! In addition to smell - it is harmful to health!

In order not to score with the twisting of the water supply hose.
- Do it when the toilet is not installed. Most often, on the toilet, a place to connect the plastic hose, so be careful, the thread can be disrupted easily. For a more dense connection between the hose and the toilet, use the special tape (forgot, as it is called). Machine its revolutions 5-6 on the thread.

How to install the toilet on the floor of the tree?

We set the toilet on the wooden floor as well as on the floor of the tile.
- Only instead of dowels, use the screws, the same length. If the screws fall into the hole, then apply the washers of the corresponding diameter.

If necessary, the use of PCS (see above, in which case).
- PCS will not hold on wooden floor. To do this, it is necessary to note the insert contour on the floor, turn over the toilet and see where the emptiness is at the base. In this place it is necessary to twist the screws half. For example, 60mm screws, then spin 30mm.
Then, to measure whether the screws do not interfere with the installation of the toilet.
- After that, you need a wire. Split between wire brand ... it will be fittings. How many screws and how to twist, decide, but not less than 4 screws!

Here you go! Probably, everything!
And more ... so as not to bathe ... pay 1000 - 2000 rubles and you will put the toilet professional.

How to raise the toilet

Forum / Plumbing / how to lift the toilet

Ask you the question of our forum without registering
and you will quickly get an answer and consult our specialists and visitors of the forum!
Why are we so sure about that? Because we pay them for it!

The apartment lives the elderly people who are difficult to sit in the standard height of the toilet in their physiological possibilities, so there is an interval of a question whether it is possible to raise it to see 20.

alex78sol

To lend four boards of the desired height, as a formwork and pour a concrete "podium", lay tiles, and on top of the toilet. And in general I in Moscow, in one social center I saw in the toilet toilet toilet, and next to the handrails are installed, so that the elderly people can rely on the hands when they get sit down.

The height of the toilet, or rather the problem from it to get up and even sit down - very relevant.

For this, manufacturers have created special high toilets for disabled people.

need advice on installing a toilet (how to raise it higher when the floor in the tile?)

I saw such a hospital. If you allow the means, you can buy and the problem will solve.

sergey

I want to add to the foregoing. Before building "Podium", prepare the installation site "Podium", with the help of a perforator or chisel, remove the tile and the upper layer of the solution. For reliability, fasten the toilet to the anchor, blown in the main floor.

Dear guest, stay!

Already many earn just communicating on our forum!
For example, like this. Or so.
You can start communicating on the forum now. Just enter vkontakte or register, it takes one minute.

But if you are passing, you can still:

How to connect toilet to the sewage system?

To connect the toilet with your own hands, special skills are not required.The main rule of installation is the correctly studied technological process of installation, which does not depend on the location of the plumbing in the house. In addition, you need to prepare all components in advance, choose the way of connecting the bathroom, which will be discussed further.

The method of connecting the bathroom to the sewer system

Connecting the toilet primarily depends on the model structure and implementation of the release. Modern type of models has a constructive structure having such data:

plumbing horizontal release with communication, mounted in the wall of the bathroom;

with the release of 45 degrees. The model is universal and allows communications with both the floor and the wall;

vertical structure, where water drains is carried out through a pipeline located under the tile at the location of the toilet bowl.

Each sanitary ware for a bathroom, regardless of the model, has its drawbacks and advantages.

Also worth paying attention to the fork of hoses leading to the sewer plum in the room of the toilet:

perpendicular plum pipe;

plum pipe, parallel floor;

plum pipe under the tilt to the floor.

In the first case, the structure of the pipeline leading to the sewage drain is perpendicular, produced according to the old sample scheme. A plus of such a construction is the dense fit of the pipe to the wall without damage the appearance of the bathroom and without cluttering the free space. Models of this kind are not in demand today and are rarely produced.

The advantages of the second scheme can be attributed to the ease of installation and simplicity of connection. Having done the installation work, you will need an instruction how to connect the toilet. After reading it, proceed to the first stage of the work, putting the bowl of toilet bowl on the drain riser and sewing the place of the joint.

How to install the toilet with your own hands: Procedure of work and possible problems

Then the basis of the toilet is to fasten with a dowel to the floor. Minus the scheme is that the expending of such a pipe is possible only in the presence of a vertical riser.

Plum pipe at an angle of 45 degrees is the best option, if you choose from the two described above. The disadvantage of such a structure is a long distance between the bowl of the toilet and the wall, which is important when connected.

How to connect the corrugation?

The best option for connecting communications is to connect corrugations. The corrugated hose is able to bend and stretched out, which allows you to smooth out errors with inaccurate sizes. To connect corrugations, materials will be required:

corrugated hose;

pair of rubberized cuffs;

silicone glue.

One end of the corrugated tube is treated with silicone and embedded in the receiving hole of the sewer exit with a tight cuff. If the leakage is absent on the joints, fixation of the base of the toilet with a dowel or cement mortar is carried out.

Difference of the cast iron and plastic pipe

When connecting the toilet to sewage, you need to have a concept, which is the difference between two types of pipes. The cast iron pipeline over time is corrosion and requires reliable sealing in places of connection of nozzles and cuffs. For sealing at the docking places, a solution of suits or a mixture based on resin is used. Silicone is used to seal cuffs.

Plastic pipes are more reliable and are made with a ready-made sealing ring, which in combination with the cuff provides a reliable connection. Such pipes serve for a long time, they are resistant to mechanical damage.

Summing up to sewage

After installing the bathroom and fastening its bases to the floor, you can connect to the toilet to sewage. The element of the sink to the drain pipe has a different structure that can be straight or at an angle.

The release has holes that are lubricated by Surikom, after which it is inserted into the fool, where the toilet is connected to the sewage system of the drain system. Also there are corrugated tubes for toilet bowls, which are treated with silicone when connected, one end is put on the outlet, and the second part is mounted in the fool.

Installing a drain tank

First of all, you need to process the drain exit from the outer part with silicone and hang the tank on the toilet. Fix the locations of the joints with plastic bolts. Then proceed to adjust the drain mechanism. For this, the level of fluid in the container must be limit to ensure a complete drainage. If the float is high, it can affect the overflow of water from the tank.

Before adjusing the drain, you need to dial water into the container to the mid-level, and as you have to set the float.

Thanks to the information provided, it is not possible to connect the toilet to the unit of the toilet and will help save finances on the challenge of Plumbing.

In the new buildings of the free planning of Moscow, there are very often cases when the owners are not satisfied with the location of the toilet or bath and a desire to transfer the toilet to a new place, and on the place of the bath install the shower cabin. But the toilet is binding to the riser and when transferring it to a new place there are problems with a slope slope. How to solve such a problem?

The output from this situation is the podium device for the toilet or shower. The advantages of this solution are as follows: Having increased the distance from the riser and moving the toilet to a new place in the plugging podium hides the drain pipe, and its output from the new place is vertical (good there are plumbing models in which the drain is vertical), also dropped from this drain through the tee To the pallet of the shower, which is also hidden in bulk design. According to existing water drain technologies, the tilt must be at least 2 cm on the trafficphone meter.

You can use a mosaic to find all the elements of the filler design, it looks especially aesthetically lined with a mosaic lined podium.

question: how to raise the toilet

It is possible to replace the toilet to install (in these structures there is also a vertical drainage).

Another solution is the filler podium in two different levels. This option can be used if: on the project, the shower cabin is located close enough from the riser, and the toilet is transferred to a considerable distance (then for a normal sling to make a two-level podium).

The device of the podium under the toilet: the pallet for the shower.

Considering that the floor level in the bathroom and the toilet should be lower than the overall level of the apartment, the filler podiums help solve float level problems.

When installing the podium under the toilet, an important feature is the place of fastening the toilet itself. The point is exactly that when hiddening the plum pipe, you can get into it when drilling a podium for fastening the toilet bowl, therefore, when laying a drain pipe, you need to consider these moments.

The same applies when weighing a drain to the pallet of the shower cabin and the installation of the ladder.

To install the toilet, you need to have healthy tools and basic knowledge relative to this process. Of course, it is better to use the services of specialists, but you can also try to install the toilet.

This article discusses how to properly connect the toilet to the sewage, which types of toilet bowls exist.

What do you need to know starting the installation of the toilet?

A compound is performed with sewage toilet with corrugated cuffs, plastic taps and fan pipes.

For those who do not know what is a fan tube of sewage, I immediately want to clarify that this is a pipe that copes with the problem of an unpleasant smell.

Considering how to connect the toilet to sewage, you need to pay attention to that corrugated cuffs are allowed to be bent at any angle and pull the length. And the eccentric cuffs are allowed to rotate around their axis.

In addition, establishing a toilet with a fan tube, it is necessary to comply with such rules:

Do not cut them.
Do not change their shape.

From the tools should be:

Perforator and drill.
Set of wrench and adjustable key.
Screwdrivers.
Bulgarian.

If there is all of the above, you can proceed to the preparatory work for installation of the toilet.

Types of toilet bowls

Today, the toilet manufacturers offer a wide range of products. The buyer has the opportunity to choose exactly the option that he most likes.

There are such types of toilet bowls:

All units have their advantages.

Repair in the bathroom: how to transfer the toilet to another

The choice remains for the buyer and its preferences.

Preparation for mounting

If you plan to change the old toilet to a new one, then you need to carefully dismantle the old product. When the attachments are removed, you need to tilt the toilet back. This is necessary in order to merge water residues. This applies to the replacement of an old plumbing product to a new one.

If this is a new building, there were not previously installed plumbing products, it is enough to bring order to buy a toilet, to prepare all the necessary tools and start mounting work.

Installation of toilet with oblique release

All toilet bowl has its own individual characteristic, on which the installation and connection process depends.

Connecting toilet to the sewage to sewage is performed as follows:

First you need to lubricate the outlet of the toilet with Surikom, mixed with the oil.
Next, the thumbnail is wound up the smallery strand, but you need to leave her tip free.
Then the wrapped strand must be lubricated by Surik.
Next, you can perform the installation of the toilet, securing the release in the opening of the sewer pipeline

It is in this way to connect the toilet to the sewage riser with the oblique release.

Installation toilet with vertical release

As mentioned earlier, the toilet with a vertical release has a siphon with an exhaust pipe, which is directed upwards. The toilet is very easy to install. The installation process looks like this:

It is necessary to make the layout of the layout of the toilet, the screw flange is installed, which is equipped with a retainer.
The center of this screw flange establishes a sewer tube.
Then the toilet is installed on the flange, it must be rotated until complete fixation.

It is noteworthy that the nozzle will be automatically fixed on the end of the sewer pipe. The toilet can be put tightly to the wall, which will definitely be an advantage.

Installation of toilet with horizontal release

Mounting toilet with horizontal release is performed using a sealing cuff. First you need to fix the toilet to the floor with the help of a dowel. Then the connection with the sewage is performed. Attachment should be very careful not to damage the toilet surface.

Installation of toilet to sewage with corrugation

Connecting the toilet to sewer with corrugation can also be independently. In general, this is the standard installation procedure, there is nothing superpower in it.

Connection is done like this:

There is nothing complicated in the process of installation toilet to sewer with corrugation.

Cast iron sewage connection

Usually connecting the toilet to the cast iron sewage is performed in homes with an old sewer system, which was made of cast iron products.

In any case, the compounding toilet with iron sewage will be carried out using such auxiliary elements such as cuffs, corrugations and sealant.

The easiest thing is established to the toilet with oblique release, since it is this type of toilet bowl that was used in Soviet times. But the most difficult to install the installation of the toilet with a horizontal release will be performed, because the cast-iron sewage is simply not adapted to such a connection.

In general, the connection of the toilet bowl can be performed independently. If you need to connect to cast-iron sewage, it is better to use the services of a specialist.

How to lift the toilet higher when repairing in the bathroom? Usually the need for such works occurs when the floor level changes and the permutation of sanitary devices. In this case, it will be worthwhile to know the methods of performing such work on their own.

First stage: Select options

In order to raise the toilet a little higher, it is necessary to combine its outlet with the output of sewer pipes. This can be done by several methods:

Use flexible plastic harmonica. This will allow you to establish a toilet on any desired height, but the reliability of the entire system will depend on the quality of the plastic harmonic, and the device itself will be pulled a little forward, which is not always convenient for small toilet sizes.

You can try to combine the axis of the outlet of the device and the sewer tube by selecting the corresponding corner of the nozzles and the use of pads. It does not always succeed, since often the angles of inclination have such values \u200b\u200bthat it is difficult to choose standard nozzles to them, and have to make a composite design.
In order not to have problems with the inconsistencies of the corners of the pipe, you can remake the sewer output so as to make the installation of the suspended toilet.

After a person is determined and chooses a more suitable one of these three options, you need to prepare tools, devices and materials, and then proceed to implement the plan.

Second Stage: Workflow

First you need to prepare a workplace. To do this, you need to remove all things that can interfere with the installation of the device to the new floor.The best option when there are no objects in the bathroom or the toilet.

The production technology is the following:

First, the toilet disconnects from the water supply system and sewage. To do this, overlap the flow of water into the tank of the device, close the central valve and remove the hoses going to the float on the tank.
It is necessary to remove all the water from the device that remains there. For this, a rag and rubber pear is applied.
Then remove fasteners on the sole of the device. Usually the toilet is mounted on a wooden board or concrete screed. If old mounts can not be removed, they cut them with chisel and hammer.
After that, you can disconnect the device from sewage. To do this, remove the device output from the sewage pipe.
Old cement coating must be removed.
It is recommended to clean well from dirt and old seal all the nozzles.
After the floor in the room is raised to a new level, you need to put the toilet on wooden bars in the place selected for installation. The horizontal surface of the surfaces is checked by a construction level.
If it is not possible to accurately combine the axis of the outlet of the toilet device with the sewer nozzle, it is best to apply flexible plastic harmonica. In some cases, it is better to apply rubber corrugation. Sometimes it is possible to make a fairly acceptable adapter from two standard pipes (for example, 135 °), which will make it possible to accurately combine the axis of the sewage pipe and the output of the toilet device, but then it will be necessary to take care of a good sealing of the joints.

Then it will be necessary to fasten the toilet on the new floor. The base of the device is powered by a felt-tip pen, mark the locations of the attachments, and then drill holes. The device is fixed with bolts or dowels.
Secure the entire system. To do this, you can use cement and sand. Increasingly, many people are fixing the toilet to the floor with the help of silicone glue, but it is not always convenient. Sometimes a foam block is used, as it is easy to cut with a hacksaw.
After these works, you must attach a tank device to the water supply network using hoses.

Installation of the suspension design

When changing the floor level in the bathroom or toilet, modern specialists are recommended to install a suspended toilet.

This can be done in two ways:

Installation is created.
A concrete base is done.

The first method implies the construction of a special design that allows you to change the level of the device and helps to fix it. With such a system, the toilet is accurately combined with its drain pipe with sewage. Installation can be closed with plasterboard.

To create a concrete base for the suspension toilet, it is necessary to purchase 2 steel studs with a m20 caliber and a length of 0.8 m. Also need screws for wood, making formwork (wooden boards or plywood sheets), washers, nuts, concrete solution.

At the first stage, you need to install a transitional clutch between the sewage and the toilet. After that, they define the places of fastening of studs in the wall. Better if the holes are drilled through. If this is not impossible, you will have to apply epoxy glue. Formwork must have 2 side and 1 facial plane. Studs will attract it to the wall, and then they are used as supports of the suspension toilet.

Concrete must be poured gradually so that the transitional coupling is not shifted. The formwork should stand 7 days until concrete dry. All connections to the toilet device must be treated with sealant.

After complete installation of the suspended design, you need to connect it to the plumbing network. Although the complexity of the installation is quite large, the service life of such a design is quite large and reaches almost 40 years.

Necessary materials, fixtures and tools:

Flexible harmonica.
Sewer nozzles and gaskets.
New, suspended toilet.
Cement and sand, concrete, boards.
Epoxy adhesive.
Sealant.
Washers, bolts.
Bulgarian.
Building level.
Rubber pear (it is needed for pumping water).
Chisel and hammer.
Wrench (it is better to use a configuration option).
Sand paper and knife.
Screwdriver, roulette, felt-tumbler.

All of the specified toilet raising methods are easily done with their own hands. But if a person has no time to do this or he does not know how to do it, it is better to call the plumbing. True, in this case, financial expenses will be much larger, but also the quality of work will be higher.

Often, when repairing in the bathroom, the need arises to raise the toilet higher above the floor. It may be caused changing the pipe outlet level, floor, plumbing location and other reasons.

Main ways to raise the toilet higher over the floor

Lifting the toilet over the floor level is carried out in several ways:

Creating a new place to install the toilet With an appropriate level -Clocked process, with partial restructuring of an apartment engineering system.
Installing a new suspended type - A common solution to such a task, which requires additional installation, possible restructuring and dismantling engineering sewage systems.
Construction of a pedestal - It is applied less often, as it requires certain skills in finishing works, special materials and dry mixtures (if the podium is made of cement or concrete). A task you can simplifyIf the podium use foam blocks.
Application of special plastic gaskets - Frequently used option that is chosen due to the simplicity of functionality and installation, availability and popularity. Suitable for cases when it takes time to create a certain height Toilet due to the physical characteristics of a person (for example, children, elderly people, disabled people living in an apartment with other tenants).
Through pipes and adapters - Also, as in the first version, you will have to spend a lot of strength and time to carry out sanitary work on the connection of pipes and change in terms of engineering communications in the apartment.

The choice of a suitable way depends on the skill and skills of the apartment owner, as well as the situation and the reasons for which such work is carried out.

Plastic coasters for toilet and gaskets to increase height

Simple and affordable tool to raise the level of toilet bowl. Highlight children's stands that help sit on a large toilet a little babyas well as classic adults - for the elderly and people with disabilities.

How do they look

The stand is frame frame with desired shape and height. If necessary, it can be equipped with a step. In some cases, a special type of consoles are used, which has a more complex shape and a separate system of adjustments.

Photo 1. Baby stands that will help sit on a large toilet to a small child, are often sold complete from the seat and steps.

Pros and cons

Plus the stand is that there is no need to dismantle the plumbing. They are suitable for models of any species and forms. Stands are used in cases where people living in the apartment need a different level of the height of the toilet. Using lined easy to change the height and configuration of the toilet seatAnd also significantly increases the level of convenience and comfort for each family member.

The disadvantages include only the fact that more complex linings with handrails or steps can take an extra room in the toilet room.

How to install

Setting the console depends on the type of design. The general principle is that the product is placed on the product bowl or above it.. To sit down to a person who uses it, it will be necessary not to the toilet itself, but on this stand.

In general, the installation process is rather simple and the user will only just explore the instruction that is attached to the product.

How else can you raise the toilet higher: a pedestal

Installing pedestal for the concept of toilet expands the dismantling of the plumbing device With the subsequent placement of it in the same place, but only a few greater height.

What can it be done

Often posts are performed from cement and concrete solutions. In addition, a tendency to make pedestals from foam block is noted. This method is the easiest performed.

Photo 2. Before building a pedestal to avoid errors, you need to measure and transfer the outline of the bottom of the toilet bowl.

How to install it

To start calculate the height of raising And they choose the foam block in size, the basis of the future podium will be formed from it. Then disconnect the toilet to remove the corrugated pipe leading into the sewer, and unscrewing the bolts that fasten the device to the floor.

Important! The toilet disconnects from the water supply and sewage. Before that it is necessary to overlap water.

The outline of the lower part of the product is delineated on a piece of foam block of a given height. Then the part is cut down and applied to the base for comparison. The edges of the workpiece processed to an even state. The finished element is glued to the floor. After drying the glue, the toilet places on the obtained podium and fix with the help of a dowel. The edges of the pedestal are aligned under the toilet So that the design does not look a foreign element, but looked harmoniously as a natural continuation or part of the plumbing.

Attention!Important maximize the edgesSo that the pedestal merging with the toilet. Subsequently if this failsThe appearance of unlocked edges will attract attention.

It is better to make fundamental changes in the bathroom during repair. If desired, the bathroom can be combined with a toilet. This transfer is theoretically possible. In practice, it is necessary to deal with various "pitfalls". Another version of the upgrade is to turn the toilet to the other side. In fact, it is necessary not only to embody the design ideas associated with the design, but also to solve the necessary technical issues.

When redeveloping the bathroom, it is often necessary to transfer the toilet to some distance from the riser

The transfer of the toilet is helps to efficiently use the area of \u200b\u200bthe room. In this case, it turns out to be placed. It is impossible to independently implement.

The transfer of sewage in the apartment should be carried out in accordance with the legislation of the Russian Federation.

Put a bath over residential premises or kitchen neighbors;
Make changes to the size of the bathroom and expand its area by combining with the adjacent residential premises;
Shift;
Fasten the plumbing and pipelines to partitions separating the bathroom with a toilet from the living rooms.

The problem of transferring the toilet to the root

The newcomer may seem to increase the distance between the toilet and the wall easily. If you decide to move the device from the riser, you need to increase the length. To successfully complete the planned process, you need an accurate plan with calculations. A large distance from the plumbing equipment of the pipeline is fraught with a breakdown of the hydraulic circuit. Incorrect connection will be accompanied by bugged sounds.

Sometimes alteration is impossible, if not flooded. Put the plumbing on the podium. The elevation provides a bias required for sewage pipes. Work is quite laborious. The height of the podium must be calculated in advance.

Transfer technology to the maximum distance according to SNiP

If we decided to transfer plumbing devices and equipment, the technical side of the question affects changes in engineering sewage. Take into account when planning the distance between the water supply and sewer. So that the room does not lose aesthetic attractiveness is important if possible to hide communications.

Transfer to the toilet from the riser - a complex and responsible event

Long distance

When you need to be in the corner and move no more than 10 cm - 20 cm, then the following procedure is carried out in stages:

Make a dismantling of an old device. Take advantage of the chisel or large screwdriver to remove the jack on the junction between the instrument and the sewer;
Carefully break the toilet with a wide chisel;
Lift the toilet. It is necessary to pull out the release of the instrument from the pipeline;
Mark the new location of Plumbing. Drill holes for fastening elements;
Change the eyeliner if necessary;
Clean the socket with a good wipe them;
Apply a layer of silicone sealant on corrugation. Put it on the exhaust pipe of the device;
Install the plumbing equipment;
Do not tighten the fasteners too much so that the device is not cracked.
Machine slots with a solution;
Take the sealant and wake the remaining corrugation. After that, insert it into the socket.

Instead of corrugations, take a small plastic pipe. This option is distinguished by durability and reliability. Another alternative is to connect with the use of linen winding. This method is considered to be outdated.

Long distance

It is recommended not to make the transfer of equipment for a distance of more than 1.5 m from the riser. It is important to know how to raise the toilet bowl. It is required to comply with the right slope. If the diameter of the sewer pipe for the toilet bowl is 100 mm, the slope must be 2 cm per 1 m; With a diameter value of 50 mm, the slope value is 3 cm per 1 m. Compliance with the recommendations will avoid the occurrence of blockages. You should also refuse to install direct angles. In order not to damage the randomly a Sanfayns product, during installation use gaskets. To transfer the toilet to the riser is very slapped work.

Special modern devices are designed to remove water far to 3 - 5 m. Plumbing pipe is connected, which allows you to effectively remove the water when it does not leave the grade. However, there are also its cons. When the electricity is disconnected, it is impossible to use the toilet.

Learn how to transfer the toilet to another place

Independent transfer: raise the toilet higher

When the owner of the apartment has no experience in the plumber, then it will be difficult for him to cope with the work independently. It is important to have an idea how to pull out the cast-iron pipe from the termination. It is required to calculate the tilt for the pipeline. Montage errors will soon be felt. Chronic blockages - an unpleasant problem, to the elimination of which you need to spend time and strength. If a system of forced sewage is needed, it is important to choose its type correctly. When the toilet smells badly, the home bathroom becomes like a public restroom, where they have not been cleaning for a long time. In order not to bring the situation to such extremes, consult professional plumbing. In this case, you will have the opportunity to take advantage of indisputable advantages:

accurate performance;
quick installation;
affordable service cost;
ease of operation.

View video

The task of the owner of the apartment to tell where the equipment is located. If you still have not chosen to plumbing, consult with professionals, they will be able to help you and in this matter. Upon completion of the installation, the owner of the device will receive a guarantee for the work performed. So the equipment will function smoothly. To make higher toilet bowls and reduce the distance to the riser - it's easy!

How to install the toilet?

In fact, there is nothing easier when installing one toilet, then it will be easier! You can already make money on it. (Joke).

How to install the toilet on the wooden floor, see in the very bottom.

To install the toilet on the floor from the tile (tile), you need:

Perforator.
Drill a 6mm winner, or 8mm. (or other diameter, it needs to be clarified by the seller, what diameter are in the set of dowels)
Dowel. (If you do not go in the kit, we specify by the seller. Depending on the holes, at the base of the toilet or 2, or 4.)
Corrugation. (In the event that the floor level has changed, or you want to slide a little to the toilet in one direction or the other.)
Level. (How to verify the correctness of the level reading?)
Depending on the situation: PCS or Selikon.

Corrugation, to connect the drain to the toilet.

We already have a tile on the floor in the toilet.
Now we need to put the toilet.
If you have a tile in terms of level, the toilet will rise by level, without the level. If not, we will have to align the toilet in terms of level. We put the level along, then across.

In order to raise the toilet from any side, use pieces of fiberboard.
need advice on installing a toilet (how to raise it higher when the floor in the tile?)

Fiberglass thickness 5mm. Therefore, for alignment - Fiberboard is excellent material.
If, for some reason, it turned out that the lumen between the tiles and the toilet was the big and the toilet is in an incomprehensible suspended state, then you will need PCS (sand-cement mixture, it is sold at 5kg, I think that this is quite enough for you. )

Drag the PCS to the state of thick sour cream.

How to understand what divided right? We make a slide from the solution. It should not spread within a minute. The solution should keep shape, but after that a slide must slowly lose the shape. Such a consistency of the solution is needed in order to when you put a solution under the toilet, it should fill the niche under the base of the toilet bowl. After the solution is grabbed, the toilet will stand rigidly.

First step, you need to collect everything and connect the plums of toilet bowl. If, everything fell into place, then start drilling.

It is sometimes very difficult to note the place where you need to drill holes for dowels. Or the hole is small, or on the tile it is impossible to draw any way. You need to take a couple of A4 leaves and put under the place where the holes will be. In order for the paper does not run away, ... secure it with a scotch. On paper can be drawn by anything. If the pen or pencil does not break into the dowel hole, then take the purified stale from the pencil and mark.

Now drill.

It is very difficult to drill tiles. The drill can not catch. To do this, use the tile drill, it with an acute end and drill easily. Just do not hurry! So that the drill does not finish very quickly, pour water into some cup and periodically lower the drill there to cool it. Do not bring it to a state when the drill will be hiped. This will lead to a rapid drill failure.

Of course, you can drill the usual drill for the perforator.

I do it, but it will take more time and experience here. In order for drilling clinking behind the tile, it is necessary to make a mark in the marked place, as is done in the core on the metal. Just be careful. Tile is not metal and can crack.
When the place is ready - drills. We put the perforator into the drill mode. (Without a bump.) Slowly, do not rush, and everything will work out!

We celebrate the root of the reasancement of the toilet.

Now we remove the toilet. If the toilet is not adjacent to the base very much, use the PCS (described above.) If the toilet is adjacent to the tile, then you need a bactericidal settlement. Do not regret and apply on the contour of the base of the toilet. We put carefully toilet, plug.
Either Selikon, or a solution of PCS, which will be released from under the base of the toilet, remove the cloth.

What other role is played by PCS and Selikon.

In the case of water to the toilet, the process of the tuning can begin, or there may begin mold. Neither, nor the other we do not need! In addition to smell - it is harmful to health!

In order not to score with the twisting of the water supply hose.

Do it when the toilet is not installed. Most often, on the toilet, a place to connect the plastic hose, so be careful, the thread can be disrupted easily. For a more dense connection between the hose and the toilet, use the special tape (forgot, as it is called). Machine its revolutions 5-6 on the thread.

How to install the toilet on the floor of the tree?

We set the toilet on the wooden floor as well as on the floor of the tile.

Only instead of dowels, use the screws, the same length. If the screws fall into the hole, then apply the washers of the corresponding diameter.

If necessary, the use of PCS (see above, in which case).

PCS will not hold on wooden floor. To do this, it is necessary to note the insert contour on the floor, turn over the toilet and see where the emptiness is at the base. In this place it is necessary to twist the screws half. For example, 60mm screws, then spin 30mm.

Then, to measure whether the screws do not interfere with the installation of the toilet.

After that, you need a wire. Split between wire brand ... it will be fittings. How many screws and how to twist, decide, but not less than 4 screws!

Here you go! Probably, everything!
And more ... so as not to bathe ... pay 1000 - 2000 rubles and you will put the toilet professional.

Nothing wrong!

You can still help the project!

Yes, I do not care the hand of the giving!

This article discusses how to properly connect the toilet to the sewage, which types of toilet bowls exist.

What do you need to know starting the installation of the toilet?

A compound is performed with sewage toilet with corrugated cuffs, plastic taps and fan pipes.

For those who do not know what is a fan tube of sewage, I immediately want to clarify that this is a pipe that copes with the problem of an unpleasant smell.

In addition, establishing a toilet with a fan tube, it is necessary to comply with such rules:

Do not cut them.
Do not change their shape.

From the tools should be:

Perforator and drill.
Set of wrench and adjustable key.
Screwdrivers.
Bulgarian.

If there is all of the above, you can proceed to the preparatory work for installation of the toilet.

Types of toilet bowls

Today, the toilet manufacturers offer a wide range of products. The buyer has the opportunity to choose exactly the option that he most likes.

There are such types of toilet bowls:

All units have their advantages. The choice remains for the buyer and its preferences.

Preparation for mounting

If you plan to change the old toilet to a new one, then you need to carefully dismantle the old product.

Toilet bowl 47 cm.

When the attachments are removed, you need to tilt the toilet back. This is necessary in order to merge water residues. This applies to the replacement of an old plumbing product to a new one.

If this is a new building, there were not previously installed plumbing products, it is enough to bring order to buy a toilet, to prepare all the necessary tools and start mounting work.

Installation of toilet with oblique release

All toilet bowl has its own individual characteristic, on which the installation and connection process depends.

Connecting toilet to the sewage to sewage is performed as follows:

First you need to lubricate the outlet of the toilet with Surikom, mixed with the oil.
Next, the thumbnail is wound up the smallery strand, but you need to leave her tip free.
Then the wrapped strand must be lubricated by Surik.
Next, you can perform the installation of the toilet, securing the release in the opening of the sewer pipeline

It is in this way to connect the toilet to the sewage riser with the oblique release.

Installation toilet with vertical release

As mentioned earlier, the toilet with a vertical release has a siphon with an exhaust pipe, which is directed upwards. The toilet is very easy to install. The installation process looks like this:

It is necessary to make the layout of the layout of the toilet, the screw flange is installed, which is equipped with a retainer.
The center of this screw flange establishes a sewer tube.
Then the toilet is installed on the flange, it must be rotated until complete fixation.

It is noteworthy that the nozzle will be automatically fixed on the end of the sewer pipe. The toilet can be put tightly to the wall, which will definitely be an advantage.

Installation of toilet with horizontal release

Installation of toilet to sewage with corrugation

Connecting the toilet to sewer with corrugation can also be independently. In general, this is the standard installation procedure, there is nothing superpower in it.

Connection is done like this:

There is nothing complicated in the process of installation toilet to sewer with corrugation.

Cast iron sewage connection

Usually connecting the toilet to the cast iron sewage is performed in homes with an old sewer system, which was made of cast iron products.

In any case, the compounding toilet with iron sewage will be carried out using such auxiliary elements such as cuffs, corrugations and sealant.

In general, the connection of the toilet bowl can be performed independently. If you need to connect to cast-iron sewage, it is better to use the services of a specialist.

Hello! From time to time in apartments and homes, you have to change the plumbing - it can fail or outretically and functionally. If the installation of complex systems makes sense to call a specialist, then install the toilet with oblique release can be on your own forces, and how to do it correctly and let us talk in this article.

Tools and materials

During the work on the dismantling of the old toilet and the installation of the new - it will take:

roulette, wrench set / adjustable key and saw for metal;
perforator + drills on concrete, a set of screwdrivers + dowel-nails;
knife, hammer, plumbing cabicle (resin strand) + Surik;
cement, fum-tape, white silicone sealant;
fan tube or corrugated cuff or cuff-eccentric.

Select the method of connecting a toilet bowl with sewage

In order to quickly establish a new toilet instead of the old, it is recommended to choose a suitable connecting cuff in advance. To do this, perform comparative measurements of the available and new toilet - if the parameters match, you can choose a cuff of the same type, which is already installed.

Hard fan pipes The system of hermetic attachment at one end is used if the release of the toilet and the input into the sewer pipe is strictly on the same axis. The dimensions of such a pipe are adjusted by trimming. Pipe with cuffs at both ends it is impossible to cut.

Eccentric cuff, Suitable for use if the axis of the release of the toilet and input into the sewer does not match a bit. Turning such a cuff can be achieved correctly connecting elements.

Corrugated pipe - Universal mount.

How to make a toilet a little higher

She has a certain disadvantage - with incorrect installation in the crisps sealing, waste can accumulate, which threatens to clog the system. But the corrugation allows you to connect the toilet to sewage regardless of the location of the entrance to the sewer.

Preparatory work

At the preparatory stage, the old toilet is dismantled. First of all, overlap the water supply to the tank and disconnect the flexible eyeliner from it, drain the water, remove the toilet seat. To dismantle the tank of the standard model - a compact, it is required to turn off the metal with the cutting screws - access to them is open in the space between the shelf toilet and the tank, or if it is possible to unscrew the fastening bolts.

After the tank is dismantled, it is required to disconnect the toilet to the floor and enter the sewer. To do this, you may need to smash the hammer the release of the toilet, as well as the place of attachment to the floor, to then unscrew the metal fasteners. The cuff, with the help of which the old toilet was mounted, it is necessary to dismantle, the place of its entrance to the pipe is to clean the remnants of sealing material and pollution. So that unpleasant odors do not penetrate the room, temporarily plug the pipe with a gogging polyethylene package.

Paul must be cleaned of contamination, cement traces or sealant. Make sure that the surface on which the toilet will be installed should be smooth - otherwise under the uneven load, the faience or porcelain product can crack. If necessary, put the tile or perform a cement screed. Please note that changing the height of the floor will affect the coaxiality of the release of the toilet and enter the sewer tube!

Installation of toilet

If the oblique release of the toilet is strictly falls into the cast iron input of the sewer pipe, the additional cuff is not required. In other cases, put on the release of the cuff, a corrugated or rigid fan tube (they wear hermetically), and then connect the free edge to the sewering hole. Check how the toilet is worth it, if necessary, cut the end of the rigid fan tube.

After a betting, making sure that the toilet rises correctly, circle the toilet to the "foot" and tick the place of attachment to the floor. Then remove the plumbing device and drill in the floor of the hole under the dowel. If there is no desire to drill the floor, fix the toilet in place will help cement mortar or silicone sealant - apply the composition inside the circuit designated on the floor and install the toilet on it. But everything is more reliable to fasten the toilet to the floor.

Fastening release directly to the sewer pipe. The annular deepening of the release is lubricated with a thick layer of turbine, then strand of sanitary cubicles is wound there (leave a free end of 5-10 cm and make sure that it leaves out, and did not get into the pipe, creating the cause of the crowding). The resin strand is also covered with Surik, after which the release of the toilet is inserted into the cast-iron socket. A gap between the edge of the termination by the walls of the release to zadach the cement mortar or fill in the sealant to completely eliminate the penetration of unpleasant odors.

Mounting with a cuff. The free end of the fan pipe, tightly on the release, is inserted into the entrance to the sewer pipe. The connection site is filled with sealant. Similarly, the locations of the cuffs or corrugated pipe with the sewer pipe are mounted.

Make sure the sealing of the connection, after drying the sealant, the pair of water buckets in the toilease is not the slightest leaks. If everything is in order, you can screw the bolts into the dowel installed in advance, securely securing the toilet. The gap between the floor and the "foot" is recommended to neatly fill in the sealant.

Next, the tank is mounted with a pre-installed reinforcement (drawings and explanations are attached by the manufacturer) and fastening bolts with hermetic gaskets. A rubber cuff is installed on the shelf, which seals the jack between the tank and the water supply hole in the toilet. Carefully installing the tank, with the back of the shelf, put on the threaded part of the bolts of the washer and screw the nuts.

Fixing the tank It is important to tighten the nuts on both sides evenly - in turn, no more than one turn to each reception. This will avoid skew and ensure the tightness of the attachment. The tank must be installed steadily, tightly, do not fumble. Pour into the tank water, check the tightness of the connections.

At the final stage, a flexible eyeliner is mounted for water supply to the tank. All fasteners are included in the aft of the toilet reinforcement. For sealing threaded connections, use FMU - tape.

Video on the topic "Installing the toilet with oblique release with your own hands":