For the separation of two rooms mainly use interroom doors. Today, these structures are made not only of wood. Sometimes apply materials such as plastic or glass. They perfectly look not only in an apartment or house, as well as in the office.

Views

Doors between rooms serve for certain purposes. Among the basic functions of these structures:

• partition between two separate rooms;
• stylish and beautiful look of the product;
• mutual noise.

The most popular material used for the manufacture of these structures is a tree. Often applies ash and pine. Oak is more expensive. The better and stronger the tree, the, respectively, and more expensive price.

Most often, the most expensive models are made from a solid wood array. They comply with the necessary requirements of high quality doors. Manufacturers make them completely different, which is why they have different colors, different designs, as well as all sizes.

Today, the doors between the rooms made of veneer are fairly popular. In their appearance, they are not at all inferior to expensive models from the bar. At the same time, their price is much lower and more acceptable for the average buyer.

The basis of these products is taken cheap wood. At the last stage of manufacture, it simply rumbles with a veneer. For an additional decor, all sorts of glass inserts or thread are used. It is desirable to install them in rooms with a small humidity. Thus, you can extend their service life.

In order to purchase a high-quality door, you need to determine:

• the amount you are willing to spend on the purchase;
• what kind of rooms in the house the door is intended;
• the overall interior of the room to be able to decide on the color of the future door.

Double and single models are also distinguished. The second form is most often applied.

Buy finished products today will not be some kind of difficulty. This can be done both in the store and on the Internet.

Gabarits.

Another issue at the stage of construction or repair is the definition of the size of the opening under the door. Planning in the future to order data from a certain manufacturer under the order, you should not worry about these parameters.

The dimensions of the Chinese door on the box are measured according to the standard scheme. The standard size of the interior door together with the box is chosen in order to save. For indoor doors, standard measurements are easy to produce.

With a well-distributed budget, it is better to think about the standard dimensions of the openings for the further installation of doors between the rooms. So, you can accurately schedule costs, because in building stores it offers a large selection of designs of various parameters.

Today manufacturers offer customers a lot of variations of door cauldons on the topic of textures, sizes and style.

However, before you take for a purchase, check the doorway - whether it corresponds to the desired size.

As a rule, the optimal parameters that are popular are the following doors dimensions:

• width - 0.6 m, 0.7 m or 0.8 m;
• usually height is 2 meters.

Now there are also a 0.55 m wide width door and 1.9 m high, and the thickness of the door frame varies from 15 to 45 cm.

Neglecting by these data, you can get into the situation when the door frame simply does not fit into an existing opening, which will lead to additional costs (extension of the hole or replace the door).

In the case of expansion, the placement of communications or plasterboard jumpers on the metal frame should be taken into account.

The inverse situation is possible when the hole is too large. Its reduction also entails costs when contacting specialized craftsmen. If you are interested in how to reduce the height of the doorway, you can use a wooden bar, plasterboard or brick.

So, correctly define the desired size of the opening:

• height and width of the ordered product;
• the size of the threshold (according to your choice);
• width of platbands;
• thickness (depth) door frame.

When building a house according to an individual plan, probably the parameters of the openings will differ from the standard. There are three options here:

• Less spent time and money. Make the holes of typical parameters and purchase the doors of the standard sizes that you attracted in the store.
• More costly financially, but with a qualitative result. Order Wizards for measurements in a company that will produce you door canvases for specific sizes. Here you can choose absolutely any model, color, accessories and accessories.
• Alternative. Purchase or order dobors (special planks are additionally attached to the box in order to increase its thickness). So you can install standard interior doors to non-standard openings.

Doors are manufactured according to numerous standards and rules, such as GOST and SNiP. They regulate the dimensions of interroom and entrance doors. An ordinary person in them is difficult to figure out due to numerous abbreviations, timing and numbers.

Common boxes of boxes have a thickness of 35 mm. That is, the door leaf box is 70 mm - 35 + 35. Now we measure the height. In the presence of a threshold, the height is shortened by 70 mm, in the absence - by 35 mm. So, the door canvas will be less than the opening in the wall per 100 mm (both in width and height).

Choosing the doors, you need to understand what dimensions have a door frame, and how these parameters affect the dimensions dimensions. Each room has its own standards, established and caused by functional features:

• door openings in the kitchen make 0.7x2 m;
• in the rooms - 0.8x2 m;
• in the bathrooms - 0.6 (sometimes 0.55) x1.9 m;
• the second entrance doors of 0.8x2 m or 0.9x2 m;
• the main inputs are 1.2x2 m - if single, and 0.6 / 0.8 + 0.4 m - if double.

The size of the doorway should be 0.08 - 0.1 M wider and 0.06 - 0.09 m is higher than the canvas.

If, for example, the dimensions of the doors 0.6 x 2 m, then the hole must be about 2.06 x 0.68 - 2.09 x 0.7 m.

Several tips, how to find out door cloths:

• The doorway without door is measured by "naked" walls. Therefore, you need to dismantle the canvas with the box before measurements.
• Measure the distance between the walls in all directions. Write down the smallest number.
• We measure the distance from the point on the floor (choose the lowest) to the top of the opening.
• The depth of the hole is equal to the width of the wall, so it is worth moving all three (left, upper and right).

If it did not work out to remove the door frame:

• Measure the distance from the center of one platband to the second center - this will give approximate results from which you can repel.
• We find the distance from the floor and to the top of the platband.
• Measure the thickness of the box, as well as the wall itself, if it serves as it.

As you can see, nothing complicated here.

Choosing the width of the door lumen, it is worth take into account what you have to enter certain overall things: sofas, tables, dressers, beds, and the like. Therefore, these things are not always "pass" into a hole with a width of 0.6 m. The optimal width is still considered to be 0.8 m.

• operactions should be less than entrance;
• the usual width of the entrance doors should not exceed 0.8 m, interroom - 0.6-0.8 m;
• standard size (width) The bathroom door should be so that you can make a washing machine, plumbing, bedside table and so on.

The door opening thickness is most often about 0.75 m. The same thickness is offered by manufacturers of boxes. With thick walls, consider the need to expand the box. Even if the difference is insignificant, you will not be able to hide it with the help of platbands.

The wall thickness is also measured at three points. If the number is the same - boldly order the standard design, if not - you have to be patched the wall in this place. If you do not align the walls, the platbands will not be able to install exactly.

Color

The interroom door must certainly be practical, but also approach your interior of your room. To pick up a color - combine their tone with a floor tone, furnishings and wall items. Sometimes rooms have different styles. In this case, it is worth paying attention to neutral premises, such as a corridor. Thus, the integrity of the interior will not be broken.

Among the most popular colors of interroom doors:

• universal monophonic white color;
• bright shades are suitable for a classic style - Mojn Oak and Wenge;
• warm tone of the dark nut;
• cold shade of birch.

What material to choose?

The cost of the doors in the construction market can be different. First of all, it all depends on what quality doors, as well as from their classification.

Select 5 main types of interroom doors:

• Doors from the wood massif.
• Doors made of glued wooden array.
• Laminated.
• Veneered.
• With PVC coating.

Wooden array doors Very rarely found in our market. Usually they are either manufactured to order, or bring from Europe. The cost of such doors is perhaps the most expensive, but also the quality of them at the height. The appearance of such doors is very expressive, and the high cost is due to the complexity of their manufacture.

The doors made of glued wooden array- The more frequent guest of our construction markets. They are made immediately from several pieces of wood, which glued together. Despite such "mosaic" of their designs, they are rather durable and perfectly opposed moisture. Their cost is cheaper than the cost of solid wood models, but the quality is practically not inferior. This explains their high popularity in the construction market.

Laminated doorsappeared in the construction market relatively recently, but quickly took their niche. This is primarily explained by their budget. Of course, they are not distinguished by the winning appearance, however, despite this, they still find their buyer. Their second plus is sufficient ease. They are made of fiberboard, which is illuminated outside.

You should not choose very cheap specimens, as they can be very short-lived.

Veneered doorsthere are much more common on the market than all other types. Their high popularity is explained by the fact that they fall into the average price segment, with an optimal combination of price / quality. It should also be noted that the variety of species of these doors is very large, so you choose from what.

PVC coating doors appeared on the market quite recently - the most recent. The material of these doors is covered with a special film from PVC, which gives the doors a few advantages - it protects against moisture and is easy to clean. The production of these doors is mainly engaged in manufacturers from China.

What are there?

Thanks to the efforts of designers, a huge number of types of interior doors have been created:

• ordinary single;
• decorated with decorative inserts;
• bivalve door canvases that give the room solemnity;
• sliding doors that glide along the wall and save space.

The harmonica fits organically into the modern interior. In addition, the door canvas is just an excellent bridgehead for creative fantasies. On its surface, you can draw your favorite cartoon characters or lay out a fun panel from the diverse materials. It's all you can do if there is a child in the house.

When buying interior doors, first of all, attention should be paid to their dimensions. The right choice will reduce the cost of preparing the opening and easily install the frame and the canvas yourself.

Standard dimensions of interroom doors

The easiest way to choose the doors for the rooms of the apartments of old houses. In the Soviet times, the high-rise buildings were built according to typical projects, and the size of the openings in all premises was regulated by GOST. The doors implemented today in specialized stores are also usually standard and have perfectly suitable for apartments in block houses and sizes.

What dimensions have openness and door canvases in old high-rise buildings, you can see below. The table shows the standard dimensions of interior doors with a box.

The standard dimensions of the doorways of interroom doors are width, thus, can be 60-90 cm. The height of them is always the same - 2 meters.

Modern doors

In new multi-storey buildings, as well as in cottages, interroom openings may have a variety of dimensions. Any regulations in this regard are not respected in our time. However, it often happens that the doors of standard dimensions are suitable for non-premises. For example, the canvas made according to GOST 21-8 is often the ideal option for the opening of the bathroom or the bathroom, and on the kitchen, depending on the planning, can lead a wide opening of 21-9 or 21-10.

Where to take doors for non-standard openings

The first thing to owners of non-type apartments and country houses, who decided to change the doors, should, of course, measure the openings. If it turns out that the standard dimensions of the interior doors do not match them, you should still pre-visit several specialized stores. Perhaps suitable designs to choose and succeed. If not - the doors will have to be ordered in the company specializing in their manufacture. The list of services such firms usually include accurate measurements of the openings, the manufacture of structures from zero and their installation. Of course, it will be covered by the cauldons and boxes in this case much more expensive.

How not to make a mistake with the choice

In order to avoid unnecessary expenses when replacing the canvas, of course, it should be known not only what the standard interior door has the size, but also about what the compliance of the dimensions of the inepar blocks and passes exist. What doors will be the most suitable in the latter case, you can see the tables below.

Size of opening	Frame size	Block size	Block size with platbands

Compliance of blocks and openings for double doors:

What could be the door thickness

The standard dimensions of interior doors with a box, therefore, correspond to the openings of typical apartments. If desired today, you can choose suitable designs and for the premises of an unusual layout. Well, or in extreme cases to order. The thickness of the boxes of modern doors can also be different. Most often in specialized stores for sale interior doors for 35 and 40 mm. Sometimes you can also meet models by 36 and 38 mm. Natural wood canvas usually have a thickness of 40 mm. However, specializing in the manufacture of interior and entrance doors of the company in most cases provide customers and such a service as the manufacture of very thick cloths from a natural material of 50 cm.

Of course, it should also pay attention to the thickness when buying. From this parameter, such doors characteristics are dependent as:

The degree of noise reduction. The thickness of the canvas, the better it delays the sounds.

The strength of the canvas.

Appearance. Thick models look, of course, solid thin.

How to measure the opening

Thus, you now know what the standard dimensions of interior doors are. Make measurements in typical apartments, in general, is not too difficult (however, as in non-standard). However, when performing this operation, it is still necessary to follow certain rules:

Performing measurements in length and width, you need to take into account possible changes in size. For example, the thickness of the future floor covering, if necessary, the ceiling finishes, etc. It should be very attentive, measuring including the standard doorway of the interior door. Dimensions for various reasons (errors in construction, redevelopment, etc.) from typical may differ.

Before going to the store it is advisable to measure including the old door.

The thickness of the wall in the opening is measured taking into account the finishes (GLC, plastic panels, etc.). If this parameter exceeds 10 cm, you must additionally buy or order a special diverse element.

Also before buying a door, you should decide on the need to install the spawn. This element is usually used in the event that the floor in the door separated by the door is at different levels.

Thus, modern doors can have a different design and dimensions. The main thing when choosing them is to make accurate measurements of the openings. What can there be non-standard and standard dimensions of interroom doors, we figured out in all details. Blocks for apartments in old houses can be purchased without problems. The doors are for non-type openings, most likely, will have to be ordered in the company specializing in their manufacture.

If you do not want to overpay for non-standard interior percentage doors 20-50, then you need to decide in advance with the doorway.

It is necessary to repel from the doors you like, the diversity of which is capable of satisfying even the most arrogant taste. Basic doors produce standard size: 2 meters high and 60, 70, and 80 cm wide.

Helpful information:

It is less likely to meet with a width of 40, 55 and 90 cm. And 1.9 meters high. The thickness of the door boxes may vary in the range of 1.5-4 cm.

Table of standard sizes of openings

Depending on the room, a typical door size can be applied.

So usually put:

• in the bathroom and toilet height of the opening is usually from 1.9 to 2 meters, 55-60 cm width, depth 5-7 cm.
• in the kitchen height 2 meters, width 70 cm, depth 7 cm.
• in the bedroom or living room, the height of the doorway will be 2 meters, the width is 80 cm. And the depth is from 7 cm. up to 20 cm.
• if the door to the bedroom is two-sided, then only the width will change: it will be either 2 * 60 cm., or 40 + 80 cm.

After plastering and alignment of the walls, the depth of the doorway will increase accordingly.

These dimensions of doorways are very difficult to overestimate. After all, if you have not taken into account them in our calculations, you may face the problem when your door box does not fit in the opening. And after all, not every opening can be increased, sometimes it is impossible, due to the features of the layout or wall design. If it is a carrier wall, then you will also come across a number of difficulties.

Even a simple plasterboard wall is not easy to reduce due to the transfer of metal profiles. In this case, you will have to overpay for non-standard dimensions of the interior door.

It also happens the opposite situation when the doorway is much larger than the door. Here you also overpay specialists when installing the door, for the narrowing of the opening.

An unpleasant situation may occur when as a result of a decrease, the platband will not be able to close the hole in the doorway. In this case, you will need to close the unclosed sections of the wall, glue the wallpaper or lay the tile. Well, if the room is not yet pissed, and if it was pissed, you will have to transfer everything.

Therefore, at the stage of the project, you need to decide on the dimensions of the doorways, then you do not have to overpay for non-standard doors or redo the opening.

What you need to know to calculate the doorway:

• height and width of the intended door
• thickness door box
• box width
• width of mine
• the box will be with or without a threshold.

Suppose you need a door with dimensions 2 by 0.8 meters and a thickness of 2.5 cm. To calculate the dimensions of the doorway, it is necessary to add box sizes to the size of the door, plus the mounted gap from 1 to 2 cm. On each side.

In the figure, the on the doorway is presented with a doorway with a door and dimensions. According to these data, we can easily obtain the width of the opening 800 + 30 + 30 + 10 + 10 + 4 + 2 \u003d 886 mm or 88.6 cm.

You can find out the width of the box on the site of the manufacturer you liked the doors.

• with the threshold 2000 + 30 + 30 + 10 + 5 + 3 \u003d 2078 mm. or 2 meters and 7.8 cm ..
• without a threshold 2000 + 30 + 10 + 5 + 3 \u003d 2048 mm. or 2 meters and 4.8 cm ..

Pay attention to the fact that the most often occurs the thickness of 7.5 cm. And therefore many manufacturers are preferring exactly this size.

If the wall is thicker or thinner, then you will need to install a good or cut box along, respectively. Without these operations, you cannot and everything will look much worse.

When repair, it is necessary to pay due attention to installing interroom doors. Of course, there are certain standard dimensions, but in order not to destroy the wall or change the cloth already selected, it is necessary to study all the nuances. In this case, it is important to correctly calculate the size of the day, know the standard and features of different types of structures. In the modern market, you can find the products of domestic and foreign, it is important to remember that the GOSTS differ.

GOST RATES SIZE INDICATORS

The parameters of the door canvase must be considered when calculating the day. Doors and box have standard dimensions approved by the state.
Table of GOST interroom cavities:

View premises SMVSOTOVA SMRUBUBIN OPERAMA SPEKUHNA702007Sanuzel, bath55-60190-2005-7komnata802007-20 Guest (double door120 (two canvases) 2007-20

If repair work was previously carried out, the walls were aligned or dismantled, the depth may not correspond to the above data.

The market offers a large selection of doors and components from domestic and foreign manufacturers. Most often, the products have a height of 200 cm, width 60, 70, 80 cm (less often 190 to 60, 70.80 cm). The thickness of the door frame begins from 15 mm and up to 45mm. Knowing the standards and dimensions of the doorway can be chosen by the optimal option. There are situations where the ignoring of the parameters ends with the expansion of the workman or the return of just the acquired canvas.

When buying a cloth of a foreign company, it is necessary to carefully carefully examine the dimensions after all their standard is somewhat different.

Doorway measurement formula

If necessary, it is not solved with the door with the door, it is necessary to take such moments in advance:

• Wheel dimensions: height and width, thickness.
• Dimensions of the door box: width and thickness.
• Width of platbands.

Example of calculations:

• Tight

Height (in DV) - 200 cm

Width (W DV) -70 cm

• Box

Thickness (T K) - 3 cm

• Mounting gap (MZ) -1 cm

Door unit (database) - 2 cm

• The height of the threshold (in P) - 2 cm

The formula for calculating the width of the doorway:

Sh two + 2 * t k + MZ + 2 * database \u003d 70 + 2 * 3 + 1 + 2 * 2 \u003d 81 cm

The formula for calculating the height of the patch:

In two + in p + 2 * t k \u003d 200 + 2 + 2 * 3 \u003d 208

Conclusion: For the 200 to 70 door cloth, the doorway is required 208 per 81.

The depth of the day: standard 7.5 cm, so manufacturers make door boxes for this value. If the web has already been bought: you have to make the box individually, wider - use a good. Therefore, it is better to calculate in advance.

Algorithm for measuring the magnitude of the doorway

To correctly measure the size of the day, it is necessary to observe the sequence of actions:

• Measure the height from the floor to the top (if the opening is not even, you need to measure in the area of \u200b\u200bnarrowing), until the middle of the platband.
• Width - from the middle of the left to the middle of the right platband (given the narrowing).
• The depth is measured in the upper, middle and lower part (to find the widest value itself).

A positive result depends on the measurement accuracy.

Calculation table of door openings Standard:

Width see	Height see	View of the room	Standard
62 – 65	195 – 197	Toilet, bath	55*190
67 – 70	195 – 197	Toilet, bath	60*190
67 – 70	205 – 207	Toilet, bath	60*200
77 – 80	205 – 207	Kitchen	70*200
87 – 90	205 – 207	Room	80*200
97 – 100	205 – 207	Room	90*200
127 – 130	205 – 207	Living room (double door)	2*60*200

Box and door leaf parameters

Dimensions of the box of interroom doors must correspond to the size of the canvas, given the gaps.

The frame must be proportional to the thickness of the wall. If there is no free space using good things that overlap the lumens.

Dobor is racks around the perimeter of the box to expand the door box.

The main element still remain the doors themselves. The standard is determined by relying on such parameters:

• Interior door height: 190-200 cm. Sometimes an individual approach is needed. When calculating it is necessary to take into account the gap between the base and the floor, so that the web is freely opened and closed.
• Width depends on the room.
• Thickness - different (depends on the requirements of the manufacturer), standard - 4.5.

Features of bivalve doors

For the living room, a successful solution in the interior design will be the installation of bivalve interior doors. ATTENTION, when calculating the size of the magnitude, increased twice.

As for the GOST: the standard is the width of 020 to 150 cm. This range allows you to get a comfortable full and functional design. Thickness - 4.5 cm.

Details about froze and installation:

If the discovery does not correspond to the specified value and does not give in to the extension, the following is necessary:

• One sash is in a fixed position and is used as needed.
• The width of this clock: 1/2 or 1/3 from the width of the standard interior door.
• The second is a full-fledged door.

Both options have a big plus in functionality: improve the permeability: easy to enter, endure furniture.

As for the height: if it turns more than the specified standards (size: 200-210 cm) at the top, a special fixed plank is attached.

Maximum size of the canvas

The widest doors of the standard are 90 cm. Only a limited number of manufacturers produce products of such dimensions. In new buildings, such parameters of the interroom door box are not used, because the design looks ridiculous or bulky. Still, such dimensions are found:

• In "Stalinki".
• In offices.

The most running material for interior dimensions (and not only) is cloths: MDF.

The door is a real interior element, is an integral part of the whole composition. In order to simplify the task of the selection, the manufacturers have agreed about the universal dimensions of interroom doors. - Their knowledge greatly facilitates the purchase. Consider what sizes exist how the opening is measured, which there are formulas for measuring the door canvase. The article will help to choose the size depending on the designation of the room, will tell about all the available GOSTS and the SNIVA, which relate to the doors and all that is adjacent to them.

So the interior doors of the standard size look like Source yuna-dveri.com.

basic information

All parameters (width, height, depth) are taken into account for high-quality installation. The opening should be much wider than the door sash, because there should be a place for the box (the shape to which the loops are attached, good-to-face boards and the door herself) and platbands. In addition to all this, accessories must be suitable for the door design, and the overall composition for the interior.

The doors, as a rule, are part of the overall design, which besides them, complement the wallpaper, furniture and small decorative elements. In this regard, dimensions may not be according to the standard and therefore in order to install the doors, a competent calculation is required. It is needed not only to fit into the interior, but also because their improper installation will bring discomfort.

Source www.akitasmexico.com.

Size by GOST

Manufacturers are based on approved state standard and existing building standards and rules (SNiP). According to them, the doors between the rooms have the following dimensions (the first value - width, second - height)

Values \u200b\u200bfor the size of the web (considered in millimeters):

• 550x1900, 600x1900;
• 700; 800; 900; 1200 (600 + 600); 1400 (600 + 800); 1500 (600 + 900): x2000.

Values \u200b\u200bfor dimming size (also in millimeters):

• 660-760; 770-870; 880-970; 980-1100; 1280-1300; 1480-1500; 1580-1600: X 2040-2010;
• 630-650; 660-760: X 1940-2030.

For imported models, the standard is the so-called DIN - 18100-18102 or DIN - 4172.

Source nelaet.ru.

When repairing or arranged space, you should always remember what kind of doors, windows, furniture, etc., especially if it concerns imported things. This will help in advance to correctly plan the budget, knowing how much money will go to the purchase of door flaps, boxes, additional fittings, plinths, in this whole essence of their versatility.

If the doorway is over a height of more than 2 meters, then for it there are completely different parameters that are fundamentally different from the previous ones.

Table for doors with a height of opening more than 2 meters:

Source portaprima.ru.

GOST is designed for all typical buildings in which most of the population lives. Based on this, each door and, accordingly, its size has its own function (for different premises).

A new parameter appears, associated with the location of the door - this is the depth of the opening.

• For kitchen - width 70 cm, height 200 cm, the depth of the opening is 7 cm;
• For bathroom and toilet - Width 60 cm, length 190-200 cm, depth of 7 cm opening;
• For residential rooms - width 80 cm, length 200 cm, depth of opening from 7 to 20 cm;
• Living room, hall - width 120 cm (consists of two cloths of 40-60 cm + 80 cm), height - 200 cm, depth of 7 to 20 cm.

How to calculate values \u200b\u200bfor opening with measurements

Do not always go through GOST or other standard. Then you have to measure them. For each parameter there is its own scheme.

• The height is measured from the lower point on the floor (if the presence of a plinth is implied, it is necessary to take into account it), to the topmost one. The opening is uneven, then measurements begin in the area of \u200b\u200bnarrowing and go to the platband;
• The width is measured, leaning on the height. It is important to note that the measurement is not on top, and exactly in the middle - the height is divided into half and measured from the central point of the right platband to the central point of the left. Again, if the opening is uneven, the narrowing is also fixed;
• The depth is measured from above and below and in the center, they find the maximum value and then relieve only on it.

Still width (from middle height) Source i.ytimg.com

Famous schemes for simplifying measurement

At first glance, it always seems that the measurement formulas are complex. But if you figure it out, you can make sure about the opposite. Moreover, such methods are noticeably simplified by the installation and are one of its stages at the layout stage - they allow the blades to know the values \u200b\u200bfor each of the opening parameter.

To start, we need specific values \u200b\u200bfor:

• Canvas (width, thickness, height);
• Door Box (width and thickness only);
• Platbands - width;
• Assembly clearance;
• Door block;
• The bottom threshold is only height.

When there are all these values \u200b\u200bfor each structural element, you need to use the following two formulas:

Width for the web + 2 * The thickness of the box + the value for the mounting gap + 2 * The value for the door block - the value of the width of the opening is obtained;

Door height + lower threshold height + 2 * thickness of the box - the value is obtained for the height of the opening. Thus, the initial data of the web and a few more additional values, allow you to know what the height of the doorway, and what is its width.

Video Description

How to measure the opening in this video:

Doors in the living room

Due to the presence of two sash, the calculation of the size for these doors is slightly different from others. The width of the doorway plays a big role. It goes on average from 1.2 to 1.6 meters. The sash can be the same width, and may differ (as a rule, exactly the length of one part, for example, 60 + 80 cm). Universal values \u200b\u200bof height, widths and depths for them are made more, because living rooms in different layouts have drastically different dimensions.

The measurement circuit is no different, but the box usually has a size larger (25 mm), so there is its own table.

Size of openings, boxes and canvas for doors in the living room Source Okna-blitz.ru.

Algorithm Combine Door Box Opening and Door Fold

The box has a very important role in the door design - it and the dops are tightly held by the door, loops are attached to it, so it is necessary to pay special attention when it is installed in order to increase the reliability and use of the door installed. The so-called technological openings are also required (14 mm on each side are, including the top and bottom), it allows you to identify the incomplete dimensions of the door and the space between it and the inserted box, it will be further about it.

There are cases when the values \u200b\u200bof each value of the opening are known, and for him it is necessary to choose a well-fit box, and it is already picking up the door itself.

The algorithm in order to find the ideal values \u200b\u200bfor the combination of these elements is nothing complicated:

• The value of the opening is taken, the average thickness of the box (25 mm) is taken and the value of technological openings (the presence of gaps) is taken into account;
• Carefully, as well as when performing outmets, values \u200b\u200bare measured for width, height and depths, which turned out, taking into account the box and opening.
• Recognizable values \u200b\u200bwith standard doors. If there is a sash having a "guest" size and it fits well - it means this is a good option. If under the existing dimensions fails to find a standard door - the product is ordered with individual parameters (all the resulting values \u200b\u200bare used, taking into account the opening and boxes).

Preparation for installation boxes - scheme Source blitz-remont.ru.

For interior doors with a box there is its own sizes:

Source Mtlarena.ru.

What is the convenience of standard sizes

Standard dimensions of interroom doors noticeably simplify life:

• You do not need to be spent on order door leafs with unique parameters (which increases their cost);
• This significantly speeds up the readiness of the repair, makes the process itself much easier;
• Allows you to order doors for all available rooms in bulk (simply indicate all values \u200b\u200bfor the opening and box).

Only at an early stage of the planning of the future premises, you can safely push the door to the second plan, because for this there is versatility.

Assortment of door structures

The market is developing, because Everyone wants to create his interior and supplement it with unique details. The manufacturer takes into account the requirements and requests of people and every year there are more and more different designs that have a unique form, dimensions, material that differ from other models of any important detail. All this positively affects the emergence of new standards.

Material:

• Glass;
• PVC (high-quality plastic);
• Tree of different breeds;
• Metal;
• MDF (dense puff panels of wood).

Source dekormyhome.ru.

But the whole essence is not even in the variety of materials, but in the device door structures. Everything is done so as to simplify the task to maximize when using the door - it is convenient to open and close, the loops do not creak. Furnitura creates a clear and expressive ensemble, and a variety of different styles allows you to use both fittings and door flaps for binding to one style, no matter what.

The dimensions of the doorways continue to have a value, because more and more universal models are created that are suitable for different openings.

Video Description

About the size of interroom doors in video:

Finally

Universality - the principle that is partly to be guided by choosing interior doors. They must necessarily approach the design, if desired, must come to the interior. A large number of sizes allows you to install the doors of any style in almost any typical room.

In the calculation of the required dimensions, there is nothing complicated, and the availability of tables for which you need to simply verify the resulting data and find the perfect option based on these parameters.

Sometimes, it happens that it is necessary to order a door for individual parameters, but it is rarely and the market can offer an option for each.