Prepare a lamp lamp or cap. What lamp latch will you use? There are two main options: an already existing lampshade that needs to be updated or a plastic container transformed into a lamp cap. This article describes how to make a lampshade of a plastic container:

• Wash and dry a plastic vessel having a lamp shape. As a rule, a large plastic container is suitable for this (see below). At the moment, do not remove the cover from the container.
• Using an Exacto knife, cut out the base of the plastic container. Here will be part of the amusing, looking down. Insert the light bulb into the vessel to make sure that it passes, not hurt edges. If it does not fit, find the plastic container more.
• If you decide to use an existing lamp shade or cap, make sure that it is clean. Clean surface is needed to secure spoons well. You can just wipe the lamp shade with a damp cloth, but if you need to get rid of spots, a weak solution of the household soap mixed with warm water is what you need. Before you start, let the lamp dry.

Determine which pattern you want to see on your lamp or cap for the lamp. Using the upper parts of the spoons, you can fix them "into the dressing", make a sink pattern, where each subsequent spoon will be slightly covering the previous one, while they will be evenly arranged or you can try to secure spoons face up. To improve the result, you first simply decompose the spoons to make sure that you liked the pattern, then try to attach spoons to the most label, using adhesive tape or office plasticine so that they keep in place. Do not be afraid to try various patterns and directions to create interesting effects - trial attempts are made in order to be reinforced and confident that the pattern looks beautifully. For samples:

• Spread the first layer or a number of spoons around the base of the container. Then put the following spoon (end forward) on the first layer of already fixed cups.
• Use a small amount of adhesive tape or office plasticine to temporarily attach each spoon to the lampsuit. Attach the cups of spoons until you do the desired pattern.

Stick spoons to the lampshair of hot glue. If you are satisfied with a trial pattern, burn the gun for hot glue. Equally spray it on the surface of the plastic container (or existing lampshar) to glue the cups of spoons:

• Carefully drip glue to the top of the spoon (nearest to the handle). Firmly press it to the lamp by a few seconds until you are sure that the spoon was glued. If you glue the spoons face up - add some glue to the back of the spoon, to the point that will be attached to the vessel.
• Continue to gluitive spoons until the container is completely covered with them, and nothing will be visible under cups of spoons. They should be evenly located on the surface of the container. Adjustments should be made, it is not too late because as soon as the glue will dry out, the cups will remain there forever.
• At this stage, if you want to give a gloss cap for the lamp, you can do it by adding spectacular stones, artificial diamonds and so on, carefully placing them on spoons. It is recommended not to overdo it with it!

In the design of the design of the room in the apartment or in the country, I want to differ something from others. You can do this if you combine incompatible things. For example, as in Fig. 1. For this lamp, some details from the old chandelier are used, supplemented by ordinary disposable plastic spoons. You can use such spoons in the manufacture of lamps of different designs. Several of them should be considered more.

Figure 1. Do not rush to throw away used plastic spoons, because of them you can collect a beautiful and interesting lamp.

Required details

To work, you need to prepare the following tools and details:

Figure 2. For the manufacture of a luminaire from spoons, you will need: plastic spoons, cord, lamp, plastic bottles, adhesive gun, stationery knife, screwdriver, cartridge, side and selo.

1. Energy saving lamp. It is practically not heated at burning. For a plastic made of plastic parts, it is very well suited, as it does not constitute a danger in fire ratio.
2. Electric filling. You should dig in your workshop and find a piece of electric cord, a cartridge for turning the bulb and an electrical plug. The cartridge must necessarily correspond to the type of the base of the lamp, which may have a diameter of 27 and 14 mm. You can also come in handy the switch of any type that is installed in the rupture of the cord. If these parts were not found in the household, they can be bought at any power store.
3. Plastic container from under liquid products. It is better to use a bottle of 3-5 liters.
4. Plastic disposable spoons. Their color may be optional white. You can buy them in any quantity in many food stores, shopping tents, cafes. They cost cheaply, so you can buy a whole package, because After the manufacture of a test product, most played fantasy and a desire to do something like that is similar.
5. Adhesive electric pistol. It may be needed to glue some details when assembling the lamp.
6. Stationery knife. It will be necessary to cut off some parts of the plastic bottle and spoons, to cut out various holes in the chandeliers details.
7. You may need seer, thin wire, booths. It all depends on the planned design of the lamp.

Back to the category

Production of the lamp

All items are prepared (Fig. 2), you can start making:

Figure 3. The electrical part of the lamp is assembled from the cartridge, forks and cord.

1. First, it is necessary to prepare plastic spoons in a special way. They need to carefully cut off the stationery knife or side of the handle, leaving about 5 mm that may be needed.
2. The plastic bottle with a capacity of 3-5 liters is cut out the bottom. It is first recommended to apply a felt-tip pen or a marker of the cut line.
3. With the help of an adhesive gun glipe cropped spoons to the walls of the bottle. Work begins with its lower part. Spoons are glued close to each other around the circumference of the bottle. The next row is sticking in a checker order. A peculiar scales from the suite of the subsequent row should be located between the scales of the previous one. The most recent top row can be glued separately in the form of a circle and close this design of the neck of the bottle, attaching it with several drops of glue.
4. The electrical part is assembled, consisting of a cord, cartridge and forks. The energy-saving light is screwed, all this is placed inside the bottle. The electrical wire is stretched through the bottle cover through a specially drilled hole. The cover rotates on the neck (Fig. 3). You can turn on the luster lamp and admire it with soft light. Options for additional decorative design will prompt your fantasy. You can use various beads, rhinestones and other items for this purpose, which you need to search among household items. Spoons themselves try to paint with phosphorescent or ordinary acrylic paints.

Back to the category

For the manufacture of a desktop lamp need one-time plastic spoons. Their amount depends on the number of tulips. It takes 6 spoons for the manufacture of each tulip. Sequence of performance:

Figure 4. For each tulip of such a lamp, you will need 6 plastic spoons that glued in the form of a booton.

1. Pens cut off spoons. For the manufacture of such a lamp, they are not needed, but they may be needed for other crafts. 3 spoons glued together with each other, forming buds. From above, the remaining 3 petals are glued.
2. The buds glued from spoons are painted with aerosol paints from the canister. Color can be selected at the request of the wizard.
3. At the site of the junction of the butter petals is made a hole for the stem. It can be drilled or burn the soldering iron, an electric delicti, a hot metal rod. The functions of the stem performs a plastic tube for a cocktail. It is inserted into the prepared hole and glued with an adhesive gun. To the stalk can be glued with leaves cut from a plastic bottle of green.
4. LED inserted inside each tulip. If the tulips buds are painted, then it can be any color. It connects to the network it via the resistor. If this is not done, it will warm up, which can lead to ignition.
5. Finished flowers are collected in the bouquet and are installed in the appropriate dishes. It can serve as a transparent container, which can be filled with multi-colored balls of aquagront. They will give extra beauty to a product created from spoons with their own hands. The lamp is ready (Fig. 4).

Such a pretty lamp can be made from unnecessary plastic bottles and spoons. I love the original ideas of design with your own hands, and even more so when it is supereconomy and provides a large space for fantasy. Ensure yourself!

Let's now consider how to make a lamp of plastic spoons.

• 3 or 5 liter plastic bottle;
• packing of plastic spoons;
• Be sure! Energy saving lamp so that the lamp is not melted;
• plastic;
• stationery knife;
• adhesive pistol.

If all the necessary things are assembled - we proceed!

1. Sut off the pens in the spoons, the stationery knife under the very base (they will not be needed).

3. Printe our spoons around the bottle perimeter.

4. The final edging glued here in this way.

The lamp to the collection is ready.

As a result, you will have this chandelier, glowing with a pleasant matte light.

So the lamp will look like the light on.

After your work can dry it, you can paint acrylic and glue rhinestones for volume. The evenings of rhinestones will flicker on the walls of the rays, creating the atmosphere of comfort and mysteriousness. And to lovers of something extravagant, you can use phosphorescent paints (they are sold in stores for artists), which are warming up when working lamp, and after turning off all night lights ...

It will be a surprise for your households! Good luck!

www.denismas.com.

Share with friends

P o p u l i r n o e:

Many of us have their own private homes, cottages, garden houses or "phasendes". If the cottage is located near the city, some families are generally moved there for all summer, and in the presence of a warm heated house spend a lot of time and winter. Life in nature is beautiful, there is no dispute, but still I want some of the benefits of civilization like water pipes. Often there is no central city water pipeline in the country, and a well is used as a source of water. The depth of the well is usually much greater than the depth of the primer of the soil (for the Moscow region up to 1.5 meters).

Of the paper it is easy and just you can make a beautiful gift package and not only ...

For the manufacture of a package, you will need: color printer, scissors and glue.

The package can be made with the children - it will be interesting and useful, and will also get a good gift with your own hands!

What if the challenge does not come to the time? Yes, and the number of young people received is not always suitable, and serial incubators are expensive.

Output one: try to mount yourself.

The camera for the simplified model of the incubator can serve as ordinary cardboard boxes, beaten inside and outside of thick paper layers, wooden frames, trimmed on both sides of plywood or plastic, filled in and between the walls of glass gamble, dry sawdust, foam.




Popularity: 5,224 views.