Doors can not serve forever, with them any, for example, they often appear ugly cracks, chips on glass, blowers and other defects. However, this does not mean that you need to immediately run to the store for a new purchase. Why do not first try to re-establish the door and thereby hide all the existing defects. For this purpose, you can take any wallpaper, even liquid, acrylic panels, mirrors and other materials. In this article we will talk about how and what can close the glass in the door canvase.

Classic wallpaper

Before proceeding with the work, you will need to prepare the surface of the door: remove the old paint from it, with the help of a putty, break all the irregularities and in the end it is good to polish. As soon as the surface is ready, you need to cut a suitable piece of wallpaper and apply special glue on it. Wait a minute of two or three and then carefully attach it to the door of the door, while carefully monitor the fact that even the slightest distortions and jams do not appear.

Next, we take a soft cloth and carefully smoothed, and a plastic spatula can also be applied for this purpose. If there is surplus, they can be removed by a blade or a stationery knife. You may want to give your creation more attractiveness, but do not know how to additionally decorate the door, in this case you can make a thin frame from a conventional foam plinth, such a solution will look very beautiful. Polyfoam also plant on glue. While everything will dry, at this time it is better to close the windows so that there are no drafts in the room.

Original door design

the cloth

Decorating the surface of the door with the tissue looks beautiful and somewhat unusual. In this case, it is necessary not only to prepare the surface, but also determine the degree of shrinkage of the selected tissue. First you need to cut a small piece from it, to measure its dimensions, well in water and wait until it dry out. After that, again begin to measure, comparing all the testimony and determining the shrinkage. If the value is large, then I wash the entire cut and hang it dry.

Preparation of fabric

Tip! To decorate the door, you can take both a solid cut of the material and the cutting fragments of various textures and any color solutions.

Door Caution Fabric Fragments

This technique today is very popular, it is called "Patchwork", it is often designers who are often resorted to the design of original interiors. For fastening the material to the door canvase, it is recommended to use casein glue or special mastic, such as "Gumilaks" and "Bustylate". You can save not only a large piece of fabric, but also by small fragments, however, it will be necessary to pay great attention to their tightness, otherwise such a decor will look very inaccier.

Decorated door

Liquid wallpaper

This material is universal. With it, it is possible to describe any surface, creating unique compositions and patterns on it. However, such a finish cannot be applied on the doors in the bathroom and other rooms, where high humidity prevails, it is better to leave the glass interior vendor glass in such premises and decorate it differently. But if you still decided to decorate the doors with your own hands in this way, then for this you need to cook spatulas, they must have different sizes, roller, kel, varnish and, of course, the wallpaper mixture is sold in a dry form. And also for work it will take a special pistol - Hopper.

Stages of work

• Before proceeding with decoration, the door should be covered with a spheolder and alkyd primer. Apply them to one layer.
• A dry mixture is wearing water and at the same time we are well stirred by its hands (this does not represent any danger). A week after ten and fifteen it needs to mix and add a keler again. The intensity of the color solution will depend on the amount of paint: how it is more, the brighter and more beautiful color. In order to create an interesting pattern on the doors, it will be necessary to knead the mixture in different capacles and, after each of them, add the keker of the right color.
• Spatula We put the finished solution with small portions on the surface, smooth and at the same time stretching on the parties, creating a drawing.
• We are waiting for a day two or three, until our creativity dry out, and cover it with colorless varnish.

Application of the mix

Mirror

If you do not know how to decorate the interroom in the house so that it looks modern and beautiful, then why not try to close the glass of the door with a mirror? It must be said, this option not only can become the main highlight in the interior, but also visually makes room space wider and lighter. That's just cut the glass mirror is very difficult, even if it is for this purpose a special glass cutter (glass cutter). It is best to close the glass on the door with special acrylic panels. Thanks to the coating of the amalgam, they provide good reflective ability, so the mirror is almost not inferior.

Acrylic panels can have different colors, you can choose one or several minutes, it will help create an original mirror panel on the door surface. It should also be noted that such material is easy to process, has a small weight, it is convenient to fix it, and most importantly, unlike glass, acrylic panels are not fighting. To attach them to the door surface, it will be necessary to apply primer on the back side of the acrylic panel, the main thing is that it is deep penetration. As soon as it is completely dry, you can mount an acrylic mirror to the surface of the door with the help of bilateral scotch. For greater convenience, you can use the mounting suckers, they will greatly facilitate work on the attachment of the acrylic mirror to the surface.

Mirror panels for decoration

Vintage style

This decision will give the interior door special attractiveness and make it the main exclusive element in any interior. In style, vintage can be decorated even the ceiling and walls, which allows you to create the unity of design. So, we will need:

• Sand paper large fraction.
• Paint acrylic white color, it is important that it has a water base.
• Glue mounted and pva.
• Black baguette.
• Varnish colorless.
• Newspapers and pieces of sheets, it is desirable that they are escaping from a tank notebook.

Staining the door surface We are compatible with decoupage technique. Addition will serve decorative elements. Of course, you can offer your own version of the door surface, for example, supplement it with acrylic panels, mirrored inserts. Before starting work, you will need to remove the door with the loops and put it in a horizontal position. During dismantling, be careful and make sure not to make a crack in glass.

First stage. The surface of the door should be painted acrylic paint. To apply it, it is recommended to take a brush with a rigid bristle. Painting should be a thin layer in one direction.

Second phase. As soon as the acrylic paint on the surface of the door is completely dry, it will need to be stolen. To do this, use sandpaper, so we will create an antique effect.

Third stage. We carry out the decoration of the main (central) part of the door surface. The sheets of a notebook along with the cooked newspapers are tearing into small pieces. Next, the box or rectangle of the desired size or rectangle can be diagram on the surface of the door and lubricate the resulting PVA glue. Immediately begin to put a messy paper on glue and immediately straighten it. A few layers are applied on top of the paper.

Fourth stage. Around the perimeter of all sections that were plated with torn paper, krepaim baguette. To do this, use the cooked mounted glue.

Vintage decoration

That's all, now you have learned than you can close the glass in the door. There are still many other options that allow you to create real masterpieces of art, watch the video. Perhaps there you will find a better solution to the decoration of doors.

In contact with

Comments

No comments yet, unfortunately, no, but you can leave your ...

New articles

New comments

S.A.

Evaluation

Svetlana

Evaluation

Sergey

Evaluation

Sergey

Evaluation

Alexei

How to close the glass door from the light from the corridor? And got the best answer

Answer from онаншан [guru]
blinds in glass size, can be multi-colored. In the evening you close them - isolation is provided! And when it is necessary - you can raise anything with the curtains. .
Blinds are most often hanging in the window size. I mean horizontal
Rolled are good only if the top edge of the glass at the door is smooth. Yes, and they are more expensive ...

Answer from Olga Goldobova (Klinovitskaya)[guru]
Self-adhesive film, a large calendar or a picture.

Answer from Kitty[newcomer]
just a towel or cover cover

Answer from Katya[guru]
Blinds is the optimal option, now a very large selection - we bought bamboo-very well look

Answer from User deleted[guru]
beautiful matter ... or double-sided paper ...

Answer from * [guru]
Blinds can be hanging on the door, but only - rolled: they are attached on the rails directly in size to the glass insert. Typically, such rolled blinds are made on balcony doors and windows, but in your case this sample will also be good. It will look quite aesthetic. Example - in the photo!
Good luck!

Answer from Yehka[guru]
Locking stained film

Answer from Yosha Sh.[guru]
Always said that buying interroom doors, do not be fond of spectacular, but not practical "excesses": besides the sounds and sounds penetrated.
Now a few ways to solve this problem, depending on how much money can be allocated to it ...
For example, very cool (and expensive 🙂 - darkening with polymers deposited on glass and reduced light-cutting when the voltage is submitted
In addition to the shutter curtains (limited by form and additional fastening), you can advise the toning film for cars link link cheaply, will allow you to preserve all the "decorations" of the glass, it is easy to apply on any glass of any shape, darkes to 75% of the light stream. And if you choose a thick "booking", then improve and sound insulation

Interior doors are often decorated with additional decorative elements, often you can see the decor in the form of a glass insert. But when using low-quality glass inserts or incorrect and negligent operation of the door leaf, it may be necessary to dismantle this fragile part. About how the glasses should be replaced correctly in the interior door, we will talk today.

How to remove the cracked glass?

Replacing the broken or cracked glass in the interior door begins with its removal from the door canvase. The greatest difficulties arise in the event that the glass insert is cracked, because it must be removed in such a way that the glass does not crumble when dismantling.

It is best to perform all work after the door is removed from the loops and is laid on a flat horizontal surface. If it is impossible to do this, you need to open the door and fix it securely at the bottom so that the door canvas do not rushed during operation.

On the cracks themselves, it is necessary to glue transparent durable tape for two sides of the glass in several layers. It is very important that the scotch captures and intact part of it. Such manipulation will allow to fix the glass and will not give it to crumble on the part in the process of dismantling.

Also necessary:

• gloves, best rubberized on a tissue basis;
• broom and scoop;
• chisel;
• several pieces of thick paper;
• little hammer.

All work must be performed in gloves, it will help protect your hands from damage. The further procedure for removing the cracked glass will consist of the following steps:

• It is necessary to establish exactly how the glass insert is fixed in the doorway. It can be initiated through the end or fixed with the assistance of the stroke.
• If the glass is installed through the end, the door will have to be removed from the loops. It can be removed only through a special hole.
• If the insert is fixed with the assistance of the stroke, then using the chisels and the hammer they need to move a little to the side. To remove all these fasteners are not necessary.
• Then the glass is slowly withdrawn from the canvas. It is better to perform such an operation together, especially if the insert has a large size. One person will have to hold the glass at the location of the crack, and the second at the same time will gently remove it from the door.
• It is necessary to clean all the grooves from sawdust, door maid or sealant.

The dismantled insert should be disposed of immediately, after wrapped it into the prepared paper. If there is some piece of glass in the process of work, it should be carefully suitable in the room.

Of particular difficulties in the implementation of such work does not occur. The main thing is to immediately prepare all the necessary material and perform actions leisurely.

It is worth paying attention to The state of the rubber bandwhich is located between the head and the glass itself. If it is badly damaged or torn, it must be replaced with a new one.

What can be replaced?

After removing the cracked glass from the web to its place, you must install a new insert. Many people have difficulties associated with the choice of suitable substitution material. Before starting to describe possible alternative inserts, I would like to say that Sometimes you can simply take a broken or cracked glass using the following options:

1. Special decorative film in cases where a crack or chip, have small size. It glues all the glass immediately so that the door looks harmonious and holistically.
2. List DVP. This option is temporary and can only be applied until the new glass is selected. To improve the appearance, it is also recommended to be a temporary insertion of decorative film.

For the final replacement of the cracked glass in the door, other materials can be used:

1. Normal glass. This material has no own decor, it is completely transparent, has a wide availability and low price. When choosing this option, it is possible to decorate it in any way in the future.
2. The organic glass has a high level of strength, and it is very difficult to break it, but the scratches on such a material appear quite quickly. You can eliminate this disadvantage using a decorative film that will decorate the door itself, and protect the insert from small damage.
3. Decorative (stained glass) glass. This option of replacement is the most stylish, beautiful and expensive. Inserting such glass is distinguished by an unusual appearance and high strength. True, it will be necessary to spend a lot of time on the selection of an interior design suitable to the overall style. Some varieties of this material will be installed at home will be impossible.
4. Tempered glass is distinguished by increased strength, fire safety and noise insulation.

Materials for replacing the old cracked glass is quite a lot. Preferred is worth it from them, which is most accurate not only in its technical specifications, but also appearance.

How to insert your own hands: Step-by-step instructions

The installation of a new decorative part in the door canvas should not begin with the works themselves, but from the measurement. It is necessary to accurately determine the size of the future insert. After performing measuring work, you need to remember that the glass itself, should not be too tight in the groove, otherwise it can burst again.

For the installation of a new insert, the following equipment will be required:

• sealant;
• small nails;
• a hammer;
• glue;
• rubber insert.

The replacement itself is pretty simply in several stages:

1. The sealant is applied on one side of the door cloth into special groove grooves.
2. The newly acquired insert is inserted into the rubber band, and then installed in the groove. It is possible to glue the glass and the tree directly without using such a rubber seal, but this installation will be unsafe, and the glass itself is unreliable fixed in the grooves.
3. The sealant is applied again, but on the other side of the door.
4. After 5 minutes, there were previously removed strokes. If necessary, they should be securely fixed, using special small nails.
5. The door canvas must be left in a fixed state for another couple of hours. During this time, the whole design will fully secure inside the door.

Insert the glass into the wooden door can not only with the use of sealant, but also a special wood or universal glue. Application sealant also remains a mandatory part, but this stage is performed after the installation of glass.

It is best to perform such work after removing the door with the loops. This installation option is most simple and suitable for glass of ordinary rectangular shape.

The technology itself can be used for other types of inserts installed not only in conventional doors, but also sliding or collapsible.

If the glass is located in the side door, and remove the canvas itself with the loops is not possible, then it is necessary to fix the hard-door web in such a way, to do not move during the work.

How to change in the Cingle door?

In addition to the usual interroom doors, today you can meet the CARD doors, which can also have a damaged glass insert. The CARGE door canvas differs from the usual in that it has special bars-amplifiers, which reliably fix the design itself in the doorway. The replacement of inserts in such a door will be performed as follows:

• It is necessary to remove the door with the loops using a screwdriver and removing the pre-plug. Unscrew the bolts from the inside of the loops.
• The door leaf fit on a flat horizontal surface located above the floor level.
• Using a ruler or chisel, it is necessary to remove the remaining plugs located along the edges of the canvas.
• We remove the fasteners of the screwdriver.
• With the help of a hammer and a wooden bar, you need to disconnect the king around the perimeter from the door itself. Direction of movements - bottom at the top. It is necessary to start removing the kings from the place where the fasteners were located.

• After disconnecting the kings, it is necessary to carefully remove it from the canvas and, putting the gloves, remove the cracked glass from the grooves together with the silicone seal.
• We make glasses measurements and get a replacement.
• But a new insert put on the seal and insert it into the grooves.
• We produce the setting of the kings to the place.
• Now it is necessary to collect and install the entire canvas in the order, reverse design analysis.

The replacement of glass inserts in the Cartig door is considered more complex than the work performed on ordinary interroom doors, so it comes to its execution it is necessary to be extremely responsible and neat.

How to fix a staggering glass in the apartment?

Not always glass in such door canvases cracks or broken. It is much more likely to hear that it simply begins to stagger and make up loud and unpleasant sounds. To solve this problem without replacing the decorative insert, you can in several ways:

• Special "sanitary" sealant should be purchased, which is applied with a thin strip into a slit, formed between insertion and wood.
• Conventional matches in one thing are inserted into the corners of the glass panel. Instead, you can use an acrylic putty, which is also applied to insert angles.
• Small pieces of cork are abundantly lubricated with universal glue and the glass perimeter is inserted into the slots.
• You can also carefully remove the strokes themselves, apply a sealant on the glass, and on top to set them again, but closer to the decorative panel itself.

All these ways to eliminate noise and mobility of glasses in the doors really help to get rid of the problem, and their execution does not take much time.

Installation options

The main ways to replace windows in interroom two, and each of them, in turn, has two varieties:

• Installation of a new insert with cooling or increasing size. In the first case, the cracked or broken glass is removed, and the new one is installed in its place, which is the same size. Such work is considered the simplest and rapid.
• In the second case, after dismantling a damaged insertion on the door canvase, the image draws a pencil, then the measurements are removed, and then the glass is purchased. With the help of a hacksaw, the desired form of the hole is cut, there are special grooves in it and only then the installation occurs. Such work requires special care of measurements and caution when drinking a new form in the door, otherwise you can only spoil all the material without solving the problem.

Apartment - Odnushka in Kope 96 years old. In tempting, of course, to increase the area of \u200b\u200bthe bathroom, but just in case I want to consult with experienced people. What problems may arise if Santechkabina is removed?

false mirror

Good day. My problem is a curve mirror in the bathroom. Noticed this moment for a long time, but not ready to give up the mirror, because It goes to a company with a single tab, which fit in my small bathroom. Interested in reasons - why does it distort? And how to solve this question? Here are the versions that I were heard by phone in SPb firms engaged in mirrors: 1. It is necessary to change the mirror itself. Here 2 options: I make a mirror, I stick it to the base (the price of the question 1000) and the mirror makes me and change on the basis of (3200). 2. It is necessary to change everything - heard the version that any mirror will distort if it is sticked up on an uneven basis. An uneven basis is very believable in my case, because The whole range of furniture Chinese for Russia ( Someone came across such a "problem"? For information - I have 2 identical curves of the mirror - ...

redevelopment of the hotel

Dear crowders, I ask for help in solving the following question. This apartment is supposed to be converted to the hotel for tourists (2-3 people, perhaps with children), give up as a hotel room, respectively. Therefore, the question: Is it possible to redevelop this apartment so that "everyone was convenient than the least effort"? I would not really like to make the walls between the room and the entrance, although (according to pre-forecasts) they are inside non-carrier. Is it possible to do without transfer the door? Apartment with a separate entrance, the door is in principle transferred. Thank you!

Help, please, with a living room design in two-bed

3M room in width and 5.7m in length. One wall is 5.7 carrier, the second 3 m with a window located is not in the middle. On the one hand, 1m to the wall, with the second 0.5m (to carrier). Two remaining plasterboard walls. The doors are located on a long plasterboard wall at a distance of 1 m from the second plasterboard wall. Standard doors 800mm open in the room. In principle, planned to put an angular sofa with a lengthless side of the roller under 3m wall. There were wallpapers in the drawing (with a turn in the size of the sofa). TV 40 "planned to put under the window in the corner where 1m walls. Wardrobes did not plan here. Something I want, but it looks like without the councils of specialists not to do. All I come across, TV on the wall or on a bedside table on a long wall And it does not fit it. I would like the color range of furniture. Wallpapers are already baking bright beige. Under the size of the sofa the angle Pokerin wallpaper with a pattern, complete to the main. Doors oak light. Sofa Beige on tone Darmer Wallpaper. Thank you in advance for qualified tips .