Earlier, the door was upheld or a similar leatherette, was considered chic, and not every apartment could boast such a decor of the entrance canvas. However, even today, such a finish will be far from unnecessary. And it's not just the use of upholstery as decoration, the strength properties of dermatin, combined with the insulation, performs some useful functions. This is a heat insulator, sound barrier, as well as protecting the canvas from damage.

So the door is upholstered by Dermatin

But, the upholstery of the wooden door Dermantine is a scrupulous process, requiring attention to detail, and compliance with technological nuances. How to perform this job to get a quality result?

Planning to restore or make the upholstery of wooden doors Dermantine with their own hands, it is worth considering the features of the work:

But, before proceeding with the immediate surface of the surface of the old wooden door with a skin substitute, it is worth a thorough preparation of the door if it is not new.

Preparatory work before tight

All preliminary preparations of the input system for surface upholstery by a substitute can be divided into several stages:

And only after that you can start finishing the entrance door with a granitolem.

Dismantling works

Before ginging the door to the skin with your own hands, you need to dismantle the door for more convenient operation. The canvas need to remove from the loops. The process itself can be performed in two ways, depending on the device of the canopy.

The entrance canvas are usually fixed in the box using card collapsible loops installed with insertion.

Dismantling in this case is pretty simple, you need to open it, and lift. After that, the door is easily removed.


The internal entrance canvas are more often fixed on card unintellular canopies. To remove them, you need to unscrew the fastening screws, screwed into the box, after which the door disassembly. You also need to remove all accessories: the locks are disassembled and removed, the handles are unscrewed, and the eyes are removed.

Dermato door prepared for upholstery

The door must be put on the stand or the table for further preparation.

Recovery process

All the old finish need to be removed, including the paint layer. If there are defects, it is not necessary to eliminate everything, the main thing is to get smooth and durable edges and end parts of the canvas. Also for saving the surface, you need to paint the cloth or open the tree with varnish.

Wooden door coating process

Special attention must be focused on the skews of the door of the door due to the cracked wood. It is important to plan the parameters of the canvas so that after the upholstery it always worked unhindered.

Material and tools

The main material for the work is the skin substitute, but as mentioned above, it happens different. Most often, the PVC-based cloth is used - vinyl slip. The substitute palette is represented by various tones, allowing the material to choose the material. Such a cloth is durable, and more resistant to abrasion in comparison with other analogues.


Dermatin or granitol is less durable, but he has not lost its relevance with the advent of modern analogues. By buying a cloth for upholstery, it is worth remembering that it needs to be taking more area of \u200b\u200bthe door itself, as the edges need to either bend on the edges, or it will be necessary to create rollers with a bend of approximately 100 mm throughout the perimeter.

In addition, the input canvases need a heater, its quality is used by traditional foam rubber, isolon or other similar analogues. Classic nails with wide decorative caps can be used by special handling with a similar material.

Different patterns of nails hats

Still in the work there may be a construction stapler, scissors, knife, measuring devices, hammer. When everything is prepared, you can start touching the doors dermatitin.

Uppermunication

As mentioned above the upholstery of entrance and interior door canvases is slightly different in technology. The first for the container is edged with a roller with a bend of the leatherette, and the second is simply tightened by dermal. The video shows the step-by-step process of the upholstery of Dermato doors.

Creating rollers for the entrance door

Initially, work is beginning to create rollers throughout the perimeter of the door leaf. The process is performed as follows:

Also, in the manufacture of rollers, you can go to another way. Initially, granite strips are fastened to the slats with brackets, after which the insulation is laid, and wrapped the edges of the dermatitis, fix the product to the tree.

Example of mounted rollers on the door

Collecting the design of rollers with subsequent fixation, you need to position them so that their edge spoke from the edge of the inlet canvas by 5-10 mm.
After, you can proceed to the immediate tightness of the skin substitute for the entire surface.

Upholstery

Technology Implementation Upholstery Entrance Door, as follows:

1. The leaks of dermatin or its analogue are measured according to the dimensions of the door, and a small tolerance of up to 10-20 mm on challenges.

   

   Truptin canvas fitting to doors

2. Bashed dermatin begin with one of the upper corners. The edge of the panel is wrapped, and one of the corners formed by the junction of rollers are fixed with decorative nails.
   
3. The thermal insulator is measured and cut down according to the door parameters, after which they spread and fasten the insulation of the stapler, or on the globes, and then additionally.

   

   The process of mounting the thermal insulator on the door

4. The top edge of the panels is stretched using a nail, attached to the opposite already fixed angle.
   
5. On the tensioned edge, the step is poured down between them, pre-calculate according to the width of the doors. Usually you need to place the fixation points at the intervals of about 100 mm.
   
6. The next step is consistently fastened by the cloth of the skin substitute for the length of the doors.

   

   Installation of the canvas on the length of doors

7. The lower edge is bend, driven by dermatin residues in size, and fixed with cloves alternately from left to right (or, on the contrary, by convenience).
8. The insulation and the trim are additionally pressed by hardware diagonals, or forming a pattern.

   

   Existing versions of the patterns with the upholstery of the door

   

When everything is ready, you need to cut the openings under the locks in the grord. And swivel handles, as well as eye. Overhead handles are mounted directly through the leatherette, after adjusting it to eliminate unnecessary folds and bends.

Interior doors

Internal and interior doors are surrounded by dermatitin, as a rule, in various non-residential premises, but at the same time actively exploited.

The main goal is to create a non-heat insulating shell, but protective against wear, and, of course, sound insulation.

The rollers are usually not required on such input systems, therefore the door tight is carried out with her own hands just around the perimeter. The internal upholstery process:

If necessary, dries under locks and swivel handles are made in the drimmer. The finished door canvas are hung in its place. The new upholstery will significantly embellish the appearance of the entrance canvas, and performing additional work in terms of heat and sound insulation.

Stock Foto Selection of upholstered drimmer entrance doors

As far as expensive and qualitative, there was no door, after some time it will lose its original appearance and will require restoration. The easiest way to give the door to the second life is to fulfill its upholstery. To cover the door, you can use a variety of materials. The technology of work from the upholstery material is practically not changed. Check out the proposed instructions, and you can easily perform repair with your own hands.

For independent doors, there are many different materials, namely:

• PVC film;
• leather;
• dermantin;
• vinyl skin.

The last option from the list is most preferred. Vinilisor is superior to dermatin and artificial skin according to the main quality characteristics and is cheaper than genuine leather.

Material for upholstery can be bought in a specialized store on a cut. In general, the size of the cut must be approximately 15 cm exceeding the door dimensions on each side.

Upholstery will require the manufacture of special rollers from the upholstery material. All you need to prepare three stripes of about 100-150 mm wide. Pick the height individually in accordance with the height of your door design.

Select the material for lining. Budget version - foam rubber. Such a subflade with a thickness of 1-2 cm.

If you wish to improve the sound and thermal insulation, the characteristics of the door use instead of the foam rubber. This is a very practical material with excellent operational and properties. It costs somewhat more precious than the simple foam rubber and significantly exceeds it in all characteristics.

Additionally, you will need to buy various minor accessories, the same decorative nails. A huge selection of such products in a wide variety of color variations is available on sale. Pick up your taste.

If you wish, you can buy upholstered nails, originally upholstered leather or dermatin. They will be invisible on the main canvas of the door, which in many situations is the right solution.

In general, try to choose nails whose color will be as close as possible to the color of the upholstery material. After restoration, the door should have a harmonious appearance, unless otherwise provided by your design project.

Work on self-upholstery doors is performed using glue. You can buy the most ordinary glue type "moment", etc. On one side of the door canvase will take about 100 ml of glue.

In the process of independent upholstery, there should not be any difficulties. Understand the proposed instructions, understand the difference between the covering of the outer and the inner planes of the canvas and proceed to work.

Wooden door finish

This method is suitable for finishing those models that open inwards, i.e. In space space.

First step. Make a special roller. With this item, you hide the gap between the door frame and directly the web. Also in some situations, the roller will contribute to a more dense fit of the canvas to the frame.

The second step. Attach the bottom of the upholstery material to the front of the door so that it finds it for about 35-40 mm. Fixation performed using a special stapler.

If the locks are installed on the doors, start mounting the material from it. In the event of your mortise locks, the mount should be started slightly below the central part of the door of the door. Hold the entire perimeter of the canvas with similar stripes.

Third step. Lay the foam or other selected filler. Preload the material on the strip of a width of about 100 mm. Use the same stapler for fastening lining. The resulting roller should be written by approximately 10-40 mm depending on the characteristics of the ratio of the doors and ornamental platbands. On this roller is ready.

Fourth stage. Measure the space between the inner edges of the roller you created and cut the tight foam band. To determine the suitable bandwidth, take away from the previously obtained roller with 10 mm on each side. Attach the finished foam strip.

Fifth stage. Start directly to the upholstery of the door. Take a piece of the selected upholstery material for an angle, carefully turn it out of the edges of about 6 cm and laid into the angle of the door web in such a way that the upholstery go a little to the surface of the previously prepared roller.

Drink a decorative nail at a distance of about 0.5 cm from the edge.

Take the upholstery material for the second top corner, just just turn it out, and hammer the second decorative nail, pulling a bit, while the upholstery.

Ensure that the sideways of the upholstery material are flattened. To do this, spend your hand along the central line of the door with a small clamp, reach the bottom and, tightly holding the upholstery by hand, attach its bottom corners to the edges of the door. If the distance from both edges is the same, you can continue to work. If there are discrepancies, the attachment of the upholstery will have to begin first, otherwise it will be uneven and ugly.

Send the top edge of the web with decorative nails with a step 1 cm. Next, on the same scheme, perform a finish of any side part, gently adding the upholstery material at an equal distance and slightly pulling it away.

Get to the bottom edge and go to the finishing of the second side part. At the end, lock the lower free edge in the stapler. This independent skin is completed. Go to the installation of the eyes and old or new locks.

If the design of the door consists of two sash, the restoration is performed in the same order. An important nuance consists only that the vertical roller needs to be placed on a sash with a handle.

Video - Door upholstery do it yourself

Wooden Door Outdoor

This is an instruction for designs that are disappeared.

First step. Close the door and transfer the projection of its box directly to the canvas. This will allow you to get a new upholstery contour. The indent on the edges is required for a "quarter."

The second step. Fasten the subdirement material with approximately a centimeter indent from the planned line.

Third step. In the same way, as in the previous instruction, it is not fixed by leaving its lower edge not fixed.

Fourth step. Make a warming roller. With an outcome, it is attached to the box, and not to the canvas. It is made practically as when performing an internal upholstery, only the volume of the inner foam is needed to increase slightly.

Place the roller from the loop side so that it is flush with the door jamb. In relation to the lock side and the upper part, the roller must be pulled out by 0.5 cm. Attach the bottom side of the finished roller to the doorway so that when it is closed it is tightly pressed against the door threshold.

If you attach a roller straight to the threshold, it is very quickly fastened due to hiding legs.

Fifth step. Fix the bottom edge of the upholstery using a construction stapler, and then install the locks, new or old handles, eyes and, if necessary, decorative elements.

There are two main options for plating a metal door design: the budget with the use of materials like vinyl skin, dermatin and them like, and more expensive using decorative panels. Check out the instructions for each of them and select the appropriate option.

Video - Upholstery and Warming Metal Doors

Budget way

Restoration of metal doors can be performed using the same materials as wooden canvases. However, in this case, there is no need for decorative carnations - everything is done with glue.

First step. Carefully lubricate the edges of the door leaf with high-quality glue and fix the porpoil stripes on it. Surplus lining Cut on the profile of the door.

The second step. Apply the adhesive composition on the end of the vertex door and proceed to gluing the selected upholstery material. First glue, then the door loops, after them will cross the locks, and at the end of the bottom door. Smooth out folds and get rid of the material distortion directly during operation.

Third step. After the glue is completely dry (drying time is indicated in the instructions for a specific means) cut extra material in the event of its presence with the help of an acute stationery knife. Be careful not to damage the main upholstery.

Fourth step. Install the eyes, handles and return to the location of the locks.

Expensive way

This method involves the upholstery of the metal design with special panels. For external upholstery, the lining made from MDF are optimally suitable. They are manufactured in several standard sizes. After such a upholstery, the door will have the point of no worse than expensive analogs of factory production.

Internal decoration perform wall panels. Pick up material in accordance with the interior of the room and the features of the operation of the door. MDF has a more attractive form, often imitating the texture of exclusive and expensive wood, but this material needs a careful attitude. The panel of plastic is much simpler in care, but not so beautiful.

First step. Measure your metal drill. You need to know the width and accurate height of the canvas. On the inside of the door you will find corners designed to increase the stiffness of the door design. The width of such corners corresponds to the depth of the door canvase. You also need to fix this parameter in measurements. It will need you when buying a sheet foam and wooden bar.

The internal height of the canvas is determined as the distance from the bottom to the top corner. The width of the inner surface, respectively, will be equal to the distance between the side metal corners. Fix the measurement results.

The second step. Go to construction software along with the results of previously performed measurements. Buy there a foam, panels from the selected material, a wooden bar and a decorative corner with a 10-15 percent reserve.

Third step. Return home and proceed to the door finish. First saw the bar on 4 parts. The length of these segments should correspond to the width of the door canvase.

Take the bar, attach it to the upper edge of the canvas and with the help of a marker or pencil, draw on the basis of the line on this brus. Just do in the bottom of the web. The remaining lumps are located on the door so that all 4 bars as a result are installed approximately at the same distance. Leave the appropriate labels.

Fourth step. Armed with an electrician, make 16 mounting holes in your door. On each bar must accounted for 4 holes. The diameter of these holes should be equal to the diameter of the screws.

Fifth step. Lock the bars on the canvas using self-tapping screws. So you get a frame.

Sixth step. Drill the mounting holes for fixing the upholstery panel. The optimal number of holes for mounting each such panel is usually provided by the manufacturer in the attached instructions.

Seventh step. Prepare in the facing panel of the opening under the eyes, locks and handles.

Eighth stage. Secure the panel. For more convenience, you can remove the door leaf with the loops.

Go to the upholstery of the inside of the door canvase.

First step. Fasten the frame bars on the canvas as you did during the outer upholstery.

The second step. Cut the foam on the part, focusing on the distance between the frames of the frame. In the appropriate parts of the foam, make holes for the eyes, handles and door locks.

Third step. Place the sheets of foam in the space between all the bars. Additionally, you can fix the foam with high-quality glue.

Fourth step. Secure the internal panels on the frame. Plastic panels are fastened with a stapler, fixing the same MDF panels is performed by kleimers.

Fifth step. Secure the decorative corner of the suitable material around the perimeter of the door web. It will hide the edge of the upholstery elements and give the door more attractive appearance.

Sixth step. Put your eyes, handles, locks, replace the platbands if necessary.

These simple instructions will allow you to update the appearance of your door with minimal financial and temporary costs.

Good job!

Video - how to hide the door with your own hands

Wooden entrance doors are very picky of our apartments. They need constant care, protection and restoration. Of course, few of us pays for this subject a proper amount of time and attention. That is why they often come into disrepair or simply lose the presentability of the appearance. There is no desire and the ability to replace the old wooden product to a new one.

But you can always upgrade it with your own hands video, give a fresh look and aesthetics, which is engaged by dermatitin. How to shelter Dermantine door? There are many video lessons showing how to do it properly. And with a clear step-by-step instruction, this will not be difficult for even people who do not have special skills and skills. Moreover, as a result, not only external beauty will be, but still noise and thermal insulation.

Before starting work, prepare all the materials and tools. The choice of material is so great that it makes sense to think about the future door design in advance. Otherwise, you will walk and choose for a very long time. You will also need a porolon with a thickness of 2 centimeters and batting, a building stapler, hammer, large scissors and nails are ordinary and furniture. First you need to prepare the door. To do this, disassembly door handle, eye, loops and all decorative elements.

Step-by-step instruction: Upholstery wooden door Dermantine with her hands video

We will make the manufacture of the so-called roller, it serves as the main element of the upholstery and closes the clearance between the door and the jamb. With the help of scissors, cut the dermatin band at 10 cm. Then place it with an inlet to the end of the door leaf and use the construction stapler. Instead of a stapler, you can use the usual hammer and small nails.

In order to avoid the uneven distribution of material in places of fixation of the door loops, cuts should be made on the Dermatin band. Now you can proceed to fastener. Place it smoothly on the surface of the wooden door and secure with a stapler. Next, the foam layer is stacked by batting in 2 layers. Batin is a reliable protection of the foam rubber and protects it, increasing wear resistance and service life.

Now you can do the dermal dermal. Cut part of the canvas in size in the door size, adding 4 centimeters on each side. Rivne to put the trimming material on the door leaf and begin to nourish with furniture nails. It should be started from the center, first at the top of the wooden canvase, then in the bottom. Do not forget to stretch the material well to eliminate all irregularities. Next, continue the attachment of dermatin around the door perimeter, slightly converting the cropped edges.

Now that the door already looks quite pretty, it remains to finish working with rollers. Batin, which remained after the door sheel, twist into the tube and wrap in the Dermatin bands, nailed to the door at the very beginning of work. Bring the resulting roller with furniture nails in increments of 7-10 centimeters.

This completed the upholstery door with his hands video. It remains only to install the eye, loops, a door handle and all the decorative elements that were on the door earlier. Now you can rejoice not only with a neat new type of entrance door, but also to your skill.

If you attach some more fantasy with the help of a metal thread and nails to create an interesting drawing, which will give the individuality of your door. In order to succeed, see how to properly hide the door canvas with your hands video.

It is not arguing about tastes and aesthetic preferences, that is why the manufacturer of the doors offer entire catalogs of the most diverse design of both the door canvases and the entire input group. For the same owners that the content of catalogs does not suit, there are huge opportunities for the upholstery of the doors of the mass of materials, one of which is perhaps the most popular, artificial leather remains.

How to sew the doors. Video

As far as the leather doors are beautiful, each owner decides, however, in practicality, this coating is difficult to reproach. Dermantine price of which is at times lower than genuine leather, and if you buy a domestic not too dense material for upholstery when using indoors, inexpensive and available in thousands of sample variations and textures. You can buy everything from the skin of the crocodile and ending with the most incredible and fantastic textures. Yes, and with less pretty smooth canvas are also available.

Upholstery Dermatin door with her own hands video of the process of which we presented above, do not require any special tools and skills, and can be separated in such a way both wooden and metal door. Another incomprehensible plus material is that under it can be deftly stubbing any insulation, which will also be isolated from excess noise. In addition, it is recently a ready-made kit for the upholstery, which includes nails with special caps, insulation, rollers, and a seaspecker cut itself.

Choosing and size Dermatin

Dermatin distinguish not only in color, but also in thickness, so choosing material, it is worth considering the complexity of the desired surface. Than Dermatin is thicker, the more difficult it will give it a certain form. But at the same time, the thick material is more difficult to damage and it is better to hold warm.

When choosing a kit for upholstery, it is worth paying attention to the size of the cut, because for metal doors and for wooden squeak size will be different. Standard metal doors will require a 12-cm dermal cut, and wooden - exceeding the size of the web for 15 cm. Nails are selected special, with a big diameter shaped hat, and the color of the hat can harmoniously look with the color of the accessories or merge the color with dermatin. Perhaps it will be interesting to look like a contrast decision if the design of the arrangement of nails is something interesting.

Selection of nails and auxiliary materials

Alternatively, some draw up each hat separately - wrap or punctured it with the remnants of the leather, it looks too whole and harmoniously. As a lining, you can, of course, use the foam rubber. It is cheaper, but a sense of him, as from the insulation, no. It is better to choose a good and soft insulation, like isotone. Metal doors are placed with a simple glue moment, following the actual algorithm of action, which we look at for wooden doors.

For the upholstery of dermatitis of wooden doors, you will need the usual tools that are in every home - hammer, dumping, passage, brush for glue, building knife and scissors. The construction stapler greatly simplifies the task, but without it you can do without it, replacing the brackets with thin nails.

Wooden door sheat technology

The main work has been completed, it remains only to do from the residues of dermatin rollers to create a pattern on the canvas. In principle, it is possible to use a decorative braid for this, and the drawing can be any sense. For some reason, rhombus enjoy incredible popularity. Feng Shui, probably.

Yes, and one more. In the word "dermatin" never happened, there is no letter N. "Dermos" - in Greek "leather", and dermatin, respectively, the material that replaces it. And in general, in such a way you can quickly update the door cloth quickly and cheaply, give the doors a completely different appearance and at the same time learn something new on the use of borrowed words. Successful to all repairs!

Leatherette - Skin substitute, is one of the most sought-after materials. The most widely material is applied in construction and decoration.

The high demand for dermatin is justified by the following characteristics:

• Frost resistance. The material well performs its functions even at minus temperatures. It also helps to keep heat in the house, so it can be used at the entrance doors;
• Durability. Material retains properties from 7 to 10 years;
• Water resistance. The material has moisture-resistant properties, which eliminates the damage of the product or insulation;
• Soundproofing. Material can be used for the front door, because noise into the room will not penetrate through the canvas;
• Easy care. To preserve the type of dematin, it is enough wiping with a damp cloth. You can use a special cream that gives the leatherent shine;
• Antiseptic properties. Do not give in to bacterial rotting, mold and other pests;
• Resistance to aggressive chemical environment. The material can be washed with any means of household chemicals;
• Low cost. To obey dermatin by pocket an average family;
• Wide range of texture and colors.

Instruction - we are trimmed with dermantine

In the process of upholstery, it is necessary to adhere to a certain technology. It will maximize the useful properties of the material, and will provide a long service life. The procedure includes the following steps:

1. surface preparation;
2. upholstery insulation;
3. upholstery Dermatin;
4. decor accessories.

Each stage has its own nuances, so you need to carefully familiarize yourself with the peculiarities of the execution of listed items.

Preparation

If the replacement of the casing is carried out, it is necessary to stock knife, passage, and, when necessary, dismissed. The procedure is as follows:

1. Eating with loops.
2. Disassembly of fittings.
3. With the help of the passage, all decorative nails are removed.
4. Dermatin and insulation is cleaned. Getting rid of the insulation can take some time if it is attached to a metal door with glue.
5. The surface to the trim is prepared.

If earlier the door was not crushed, then all the fittings are removed. It is necessary to remove all the elements that are discarded on the surface. Under the dermatin should go flat surface, so you can align the relief using the plywood stove. It can be attached to ordinary nails. It is important not to forget to process wood with special means.

Insulation

First you need to decide on the insulation material. The most suitable under dermatin are:

• Porolon. Low price, a wide range of density and thickness. It has an operating time equal dermatist. Possesses medium insulating properties;
• Batting. Inexpensive material, with a service life of 30 years. However, over time, peasants, and can absorb moisture. Is toxic when burning;
• Isolon (subspecies of polyethylene). The most modern option. It has good insulating properties. The most expensive of all materials, but the ultimate cost will not be too high.

On the wooden surface, the insulation is fixed with a stapler. From the outside of the edge, it is necessary to retreat to 8 cm. On the entire area, without an incidence, the insulation is applied. The markup is applied to work the stapler or clogging of nails. The step between brackets or nails should be 10-15 cm. Processing is carried out throughout the perimeter.

For metal surface, glue is needed, which is also applied around the perimeter, retreating up to 8 cm from the edge. You must not forget to crop the insulation on the handle, castle and eye.

Preparation of tools, accessories

To rationally use the time, it is necessary to get a set of necessary tools before the upholstery. The set includes:

• a hammer;
• stationery knife and, if necessary, scissors;
• stapler (if not, the hammer is used);
• roulette;
• marker;
• tassels (for metal surfaces).

The list of tools and materials for wooden and metal doors is slightly different. Therefore, the technology of plating each material has its own. It is also important to acquire immediately by all materials:

• leatherette;
• insulation;
• staples for a stapler or nails (wooden surface);
• glue (metallic);
• decorative nails;
• tape (in case you need to additionally fix the dermatin, and decorate the door).

Reference! Choose decorative designs for design will not be difficult, since the market is filled with products of different shapes, values \u200b\u200band colors.

Upholstery technology

Work together will be worse. The second person will help stretch the cloth for the convenience and flatness of the relief. The edges of the canvas are always flexing inside, which will make the field of durable and aesthetic field. Positions must be several centimeters. The wooden door is ridiculous with carnations with a decorative cap. Step from 10 to 15 cm.

Important! It is necessary to ensure that the insulating rollers do not look out from the grounds.

Dermatin should not cover the door to the very edges. Several millimeters need to retreat, which will provide free movement.

Figure design is often used with decorative nails. Soft insulation allows you to create a relief on the surface, which will completely transform the door. Be sure to mark the marker to mark the places for installing accessories. Next, cloves are clogged, which usually have a removable decorative hat, so as not to damage it when mounting.

There are a large number of drawings that can be created on the surface: from simple points to geometric shapes, such as diamonds, squares. On the Internet you can find many schemes for furniture nails. Between the nails, you can stretch the decorative thread that will change the drawing and relief.

For the metal door, the drawing should be inventing even at the preparation stage to fasten the base of the screw buttons. In the insulation and dermatit, fine holes for screw buttons are pre-done.

Wooden Door Upholstery: Video

Upholstery has its own nuances. Wood needs to be careful. Therefore, often wooden doors have a non-primary look. A good restoration option is Dermatin's upholstery.

The tree must be treated with an antiseptic. Working with a wooden cloth, the lining must be fixed with a stapler. Since glue is required for the iron surface, the wooden canvas to knock the brackets much easier.

Furniture cloves are used on the edges.

To decorate the doors correctly, you need to follow the instructions given on the video.

How to shelter the metal door dermatitin?

The metal door is usually placed at the entrance, so it is extremely it is important to use high-quality insulation. It is often insulated only the inner side, however, the range of decorative accessories allows you to decorate an outer side using the insulation.

For a metal door, insulating rollers are not required from the outside. The size of the insulation should be less than 1-2 cm around the edges of the surface area. Dermatin needs to take a piece more by 5-6 cm around the edges than the door area. This is necessary for the bend. The upholstery process consists of the following steps:

1. Glue is applied around the perimeter, retreating up to 2 cm, and thin stripes in the area.
2. The insulation is applied, and pressed for a while. The lifetime of glue is listed on the packaging.
3. Starting from above, glue is applied to the opposite side of the product at a distance of 5 cm from the edge. Press the dermatin for the grasp of glue.
4. Similarly, the procedure is carried out on the side edges. It is important to pull the cloth to a uniform relief. Sometimes you have to cut off the extra pieces that will prevent close the door.

Inner side

The inner side of the entrance door can be insulated with polystyrene foam. Thus, it will be possible to simplify the upholstery procedure of Dermatin. The insulation process is as follows:

1. By the door area, the frame is fixed under the foam. This uses strips having polystyrene foam plate thickness. Reiki are fixed using metal screws, which are fixed in pre-done, holes.
2. All large seams and joints are closed by mounting foam.
3. Foam plates are installed in the frame, which are fixed on special glue. The gaps between the plates and rails are also close to the mounting foam.
4. A sheet of plywood, smooth door area, is nailed to the raids.
5. Next, the procedure is similar to the upholstery of wooden products. It is just important to monitor that decorative nails be nailed to the location of the plates.

From the inside, the warming rollers are attached to the door frame. They must be placed in a leoping drimmer. From the reverse side and on top of the ledge should be up to 5 mm. Bottom, the roller is located at an altitude of 1.5-2 cm from the floor.

When choosing a material for upholstery, it is important to remember the disadvantages of Dermatin:

• Low fire safety. Fast flammable material, which, when combustion, highlights caustic smoke;
• Not the most durable materialwhich is easily scratched and cutting;
• With mechanical damage it will not be possible to return the former look.

There are also important points that need to be considered when choosing Dermatin:

• The material must be elastic. The hardness of Dermatina testifies to the fake;
• Choose a coarse cloth;
• The sharp smell indicates low quality of the canvas.

Conducting Dermatin's upholstery, it is important to maintain the sequence of the process, and take into account the features of the materials used. If the technology is not broken, then this upholstery will last up to 10 years.

Source: https://tkaner.com/materialy/dermantin/kak-obshit-dver/

Step-by-step guide to Dermantine Doors

Dermantine doors upholstery - an easy and inexpensive way to decorate and insulation of the home, which begins with the entrance to the house or apartment.

To fulfill this job, you will need knowing some features of the doors.

Namely: the properties and characteristics of the dermantine used by the lining material, tools when working with wood or metal, decorative, fasteners, and more.

Dermantine (from ancient Greek leather) is a grade of artificial leather made of cotton fabric and a nitrocellulose layer covering the fabric from one or two sides.

Dermantin for the upholstery of the doors is positioned on the market as a substitute for an expensive genuine leather, not inferior to it in separate characteristics. It is also used to upholstery furniture, book elements, bags, wallets and car salons.

Dermantin is a finishing material that has the following pluses:

• Not subject to rotting and decomposition, resistant to various microorganisms;
• Moisture-resistant, does not allow moisture to penetrate into the layer of lining material, protecting it from the appearance of mold and unpleasant odor;
• Relatively durable material capable of listening to ten years with proper care;
• Resistant to abrasion and effects of chemical reagents (acids and alkalis);
• It is easily clean and cleaned by conventional detergents: soap and powder;
• It is frostable, able to withstand temperatures up to minus 35 degrees (depending on the type of dermatine).

Despite all the positive properties of Dermantine, many are not satisfied with its disadvantages, namely: with the slightest damage (cut or break), the leatherette cannot be repaired and replaced with a separate part, thus the complete coverage of Dermantine doors is required.

When combustion, the leatherette highlights harmful substances, unsafe for human health and contributes to the rapid spread of fire, as fuel and fires.

These minuses are not so important if you consider that Dermantin has a lot of useful consumer qualities, some of which are described above.

The distinctive properties of Dermantine include that the leatherette can easily and simply cut, it does not roll, it does not occur and does not give a shrinkage. In addition, there is a fairly wide selection of types of coloring material from gray to red. So you can choose what the most harmonious fit in the interior of the apartment.

What characteristics need to take into account when buying leatherette? When buying a dermantine for upholstery, attention should be paid to how the material is stretched, it does not form cracks during the tension. Also look at such a parameter as wear resistance, it must be at least 30,000, and better all 50,000 cycles. The greater the number of cycles, the stronger the fabric to abrasion.

Dermantin should be resistant to the appearance of fesoms from the fold of the material and scratches. Also, consider the characteristics of dermatin on resistance to ultraviolet radiation, if your door is under the right rays of the sun most of the time.

The surface of the leatherette can be smooth or matte, imitate the aged skin, etc. Pay attention to the flower range of artificial coating, what color and texture will be best harmonized with the design of the handles and loops, eye and other fittings.

Normal and decorative upholstery

Choosing a force for upholstery in the store, take into account the type of doors' tanks. There are two types of tie: ordinary and decorative.

Ordinary upholstery includes a simple finish of the door leaf with a smooth leaf of the leatherette, which is attached to the base only around the edges. The perimeter also creates a decorative tape, fixed on the door every 10 cm.

Decorative or regulatory upholstery Dermantine doors is a peculiar finish performed on the basis of wood or MDF - panels that are navigable to the door canvase.

First, the fabric is tensioned throughout the door of the door, and then in separate places it is fixed with buttons or nails with leather caps.

At the same time, the pattern on the canvas from the buttons may be rhombid or square, depends on the preferences of the room owner.

Schemes and drawings of decorative upholstery.

Elements of the trim for the wooden door: rollers, lining material, nails

When preparing for a drawing, it is important to know about the basic materials and elements, thanks to which the process of plating the door is.

Rollers

Upon the upholstery of Dermantine doors use rollers. The roller is a special element that serves to protect the house from drafts and cold. It forms a tube of lining and dermantine, nailed around the perimeter of the entrance to the door leaf or on the door frame.

The method of accommodation depends on the type of door opening. If it opens the inside of the room, then the roller has from the back of the entrance to the house. The roller should go beyond the box of several millimeters. At the same time, the distance between the blade and roller should be so that the roller "slowed down" the opening of the door and she slammed with a little effort.

With the method of opening the design, the roller is naked to the door canvase. At the same time, it is fixed first, and then add a lining.

Dermantine doors' upholstery is carried out without roller only in one case: if the metal design is installed without special bars, allowing you to fix rollers to them.

Lose material

The upholstery lining is most often used foam or isolon with the addition of batting. It is not excluded to use one wattin or syntheps. When applying the latter, it turns out a more rigid and ribbed design.

Porolon allows you to achieve softer and smooth surface drops. It has the best properties of sound insulation than batting and syntheps, and the most outstanding thermal insulation boasts isolon.

Isolon is a new lining material from polyethylene, more expensive, but also more perfect. It does not miss the cold air and absorbs noise, being an environmentally friendly material.

Nails

Upholstery Dermantine doors is carried out using special nails having broad hats. Men's nails can be both metal and leather (dermatin). Steel nails are silver and golden.

Leather nails are manufactured by hand, so their cost can be somewhat higher than normal. In addition, there are special decorative nails serving the decoration of the doors.

To betray the door canvase, a beautiful and modern view is not at all necessary to spend huge amounts to pay to the masters on the drawing. The upholstery of the Dermantine door is made easily and simply, only the correct preparation of the door to the drawing and tools with materials is necessary.

Preparation Door to a Treatment

How to determine the dimensions of the material necessary for the upholstery of Dermantine doors, given the dimensions of the door canvase?

The leatherette should be equal to the door area plus 15 cm on each side. For rollers, one cut is required 14-15 cm wide and a length of equal to the height of the door and two cuts, out the width of the door canvase.

The number of rollers increase if the door opens outwards (all four sides). The foam or isolon is cut out the size of the door cloth, the thickness of the insulation should be no more than 2 cm.

We still calculate the number of nails. It depends on the drawing and distances between nails. For a standard door, it may be necessary somewhere 50-60 pieces without a drawing.

Tools for work: hammer, stapler, knife, pliers, scissors, nails. For metal doors, the upholstery is carried out without nails, on adhesive basis. The glue will need at least 100 ml.

Technology covering doors

The door is released from everything too much: from the handles, loops, old upholstery, etc. At the first stage they will only interfere. Methods for fastening the leatherette to the door canvase differ depending on the door manufacturing material.

Wood

We make rollers: directly on the doors fix the leatherette strips face down with a stapler. We are deploying the tube insulation and convert, closing the foam. We clog the stapler or nails. At the bottom of the door leaf, the material should be scored so that the distance between the roller and the floor is 1-2 cm, otherwise the roller will simply move in places of touch to the floor.

We strengthen the lining: a stapler fastener from the middle of the door leaf (as the likelihood that the material turns to zero). The lining is dripping so that the distance to the edge of the door was 1-2 cm. On the stroke of the foam onto the batting (it protects the foam rubber from damage).

Krepim Dermantin: First, we turn on the top 6-8 cm and fix the nails, follow the folds and the folds and the races. Then, straightening, stretch on the sides and clog nails around the door perimeter. Properly stretched material does not frown and does not form a fold. Distances between nails maximum 10 cm, minimum 5 cm.

For the metal door, the process is a bit faster and easier, the mount is occurring with the help of glue.

Metal

The door is removed and put on a flat base, for example, four stools. Loss of glue around the perimeter of the canvas and in the center, fix the insulation. Press the foam rubber to the surface and leave a little dried.

Then glued the main cutlery cut starting from above, just like with a wooden structure, moving to the sides and ending with the bottom.

We hope our article will help you easily and easily fulfill all stages of work.

Source: http://o-dveryah.ru/remont/obivka-Dermantinom/

How to hide the door

Taking orders daily from 9:00 to 21:00

(detailed video instructions For self-upholstery doors, look at the bottom of the page)

In this instruction, we will tell you about how to put the entrance door yourself. For this you will need: 1. Vinilisza (Dermantin, Artificial leather, leatherette, PVC film, vinyl and leatherette). Viniliskow is sold on a cut, width, as a rule, is in the range of 110 centimeters to 140 centimeters.

If you have a standard metal door, then there will be a piece of matter for its upholstery, the dimensions of which are more than 10-15 centimeters. If your door is wooden, then it is necessary to take into account that in addition to the sheathing of the main doorway, it will be necessary to make rollers for which the dermatine strips 12-15 centimeters are used.

We will need three strips in length equal to the height of the door.

2. Lining material. For these purposes, it is possible to use a thickness of 10-20 mm thick. If you need enhanced thermal insulation and noise insulation, then pay your attention to such a material as isolon.

The foam rubber is sold by the meter size by two, which is just suitable for high-quality door upholstery.

3. Upholstery decorative nails. Usually used special furniture nails with a wide hat. The color scheme consists of shades for gold, silver, bronze and copper. We recommend picking up the color of the nails coinciding with the color of the locks and the handles. Thus, your door will look quite harmonious. Also in the construction markets you can find nails, whose caps are pulled by vinilies. You can choose nails that match the texture and color with the selected material, or you can turn around to play in contrast.
4. Glue. It will be needed if you have an iron door, in which no holes for nails are provided. For our purposes, the "moment is universal" is well suited. For pasting one side of the upholstery, there is enough tube with a capacity of 100 ml.5. Tools.1) Building Stapler and Staples with Leg Length 8-10 mm.2) Hammer.3) Scissors.4) Knife (You can use a regular stationery knife with interchangeable blades) .5) Unscrewing. 6) Pasali.7) Tassel ( For plating a metal door).

After you have seen that all of the above items are available, proceed directly to the upholstery process. First of all, it is necessary to dismantle all the locks, door eyes and get rid of the old trim (in the event that you need to move the door). Here we will not describe this action, and immediately begin the story about the main thing.

At all, it is not necessary to remove the door with the loops, as advised in many similar instructions. So, we divide our guide into three parts: the upholstery of the inside, the upholstery of the outside and the pasting of the metal door. But remember: instructions on the upholstery of the door gives only general recommendations and does not take into account the specifics of a particular door.

In some points, you may have to turn on the smell.

How to gather a wooden door with your own hands

Consider the situation when the door opens inside the apartment. To beautifully cut the wooden door yourself, it is desirable to start working from the manufacture of a roller, which will visually close the gap between the door frame and the door itself, and in some cases - and tightly lay down to the box itself (it depends on the design and profile of the platbands).

First, we take one strip of dermantine and with the help of a stapler you feed it with the front side to the door surface so that it goes to the door for about 3-4 cm. If your door lock is installed on your door, it is better to start to nip the roller from it. If all mortise locks, then begin to sow a door from the top corner of the loop side.

Extremely thus the entire perimeter of the door strips of the leatherette, proceed to the styling of the foam rubber. It is necessary to cut it into the strips of 8-10 cm wide. The stapler fasten them on the doorway, we bring and nail the material so that the resulting roller spoke is 1-3 cm. Depending on the relative location of the door and platforms.

Roller ready.

Next, we measure the resulting distance between the inner edges of the roller and cut out the foam rubber, using these sizes one centimeter on each side. The stapler fasten it on the door canvase. The final part remains - to hide the main surface of the wooden door.

We take a piece of dermantine for an angle, we bring the edges by 5-6 cm, lay in the angle of the door so that the material is slightly entering the roller and nail a decorative nail with a hammer, retreating from the edge of about 5-7 mm. Then we take the second top corner of the material, also we add it and, slightly pulling, scoring the second nail.

Next, you need to check, exactly leaving a piece of leatherette relative to the surface of the door canvase. To do this, in the middle of the door, a little pushing, spend your hand from the top to the niza himself and, holding one hand, the second we apply the lower corners of the matter to the edges of the door, smoothing them from the center.

Accordingly, on the left, and to the right, the distance to the edge of Dermantine should be the same. Making sure that the beginning is right, we continue the upholstery of the door. You nail the top edge, making the distance between the nails 10-12 cm.

Then we start to do the same with any side side, converting artificial skin at an equal distance over the entire length and slightly, but not much, pulling it. It is important here that it is not to drag Dermantin, otherwise you will get something like skirts with folds.

Fix it will be not easy, as you have to pass out already scored nails, while there is a high probability that you accidentally damage the upholstery material, and in any case, there will be traces from nails. Reaching to Niza, proceed to the second side.

Last but fix the lower edge of the upholstery material, having previously calculated the future distance between the nails so that it was the same throughout the bottom of the door. Everything! Door of the uphreat. It remains to install locks and eyes. Help the wooden door with their own hands is quite difficult to the unprepared person, so many firms offer their services for the upholstery of doors.

How to shelter the outside of the wooden door himself

The outer side of the wooden door should be hampered by dermantine somewhat in any way. First of all, you need to close the door and pencil to draw the projection of the door frame on the door leaf itself. In other words, make a pencil line throughout the perimeter.

It turns out the outline of the future door sheath, and the remaining indent is needed for the so-called "quarter" door. If the door is installed professionally and the locks are properly adjusted, then the door canvas should fit tightly to the box and, if with the upholstery we will earn the dermantin per line, then in the end the door simply will not close.

Now you feed the lower part of the insulation roller. Freshing it on the door so that in its closed position he firmly lightened to the threshold. For this, we already have an outlined border below. If the bottom roller navigate to the threshold itself, then over time it wipes from constant hiding legs. Next, fix the lining material with an indent from line 1 cm.

and similar to the previous paragraph, you feed the main piece of vinylister. Now it is necessary to make a warming roller on the right, on the left and upstairs. In this case, it will be attached on the door frame. It is done in almost similar to the inner roller, only it is advisable to fill in a large number of foam rubber.

From the loop side, we place it flush with a jamb, and with the upper and keyfields - we push about 3-5 mm by approximately 3-5 mm, depending on the size of the slots between the door blade and the box. If the roller make a roller too big, the door will be closed hard, with effort.

If the roller succeeds in a small size, it will not perform its main function - sealed opening. Therefore, it is important to catch the Golden Middle. In conclusion, you feed the remaining bottom edge of the trim and install eyes, handle and locks. Do not rush at this stage. As they say, it will die seven times - a rejection once.

Do in the upholstery of the slot under the locks and handles with accuracy, do not cut off too much. It will be offended at the very end of the process to lock all the work done. Now you know how to see the outer side of the wooden door himself. This will significantly increase its insulation properties, as well as the input door noise insulation.

How to hide the metal door dermatin

We take a tube with glue and brush and wipe the entire perimeter of the metal door. Then we apply a sheet of foam rubber and, slightly pressing it on it, glue. Further, the stationery knife is cutting into the foamonalone exactly along the profile of the metal sheet. If the blade is sharp - this procedure will be quite easy and pleasant.

Now we apply the glue to the top end of the door (if it is the inner side) or on the back side of the top nickname (if it is the outer side). Using glue, be sure to follow the instructions for use! Further glue Dermantin and, similar to the method above, we check the uniformity of its distribution.

Then we glue the leatherette from the loop side. And then - and from the lock side, pulling the right hand with a lightweight effort, and the left - driving the surplus of Dermantine. So, the lower edge remained. Apply glue from this side of the metal door of the most difficult.

There are situations where the gap between the lower edge of the iron door and the floor is only two to three millimeters. If you can't glue the leatherette from below, you will have to remove the door from the loops. Thus, you can significantly facilitate the task.

When the fabric is glued with all four sides, the stationery knife is gently cutting off the surplus on the corner at the shelter of the end and the nickel (the GRATOR), put the eyes, door handles and locks. As you can see, wining the metal door itself is quite possible. Try - and sooner or later you will succeed!

Source: http://profobivka.ru/obitdver.html.

How to see the door of wood, metal

The easiest and most popular way to give the door attractive appearance is to hide it with some material. It is possible to do it out of the room, and outside, use only different materials and different technologies. But in any case, the process is called "doors". All subtleties and nuances are below.

What can you beat the door

There are two types of doors upholstery - soft and rigid. Soft make two materials - Dermantine (Dermatina) and vinylisodes. Dermantin is a woven cotton base covered with nitrocellulose film. Popular This material was in the 40s-60s of the last century, as it was practical and inexpensive.

A little later there was a vinyl slip. This material is made on different bases - woven and nonwoven, drawn and not. Accordingly, the artificial leather has different properties. A layer of polyvinyl chloride (PVC or PVC) is applied. It is more durable, chemically neutral.

It has only one significant disadvantage - it reacts poorly to ultraviolet rays - loses elasticity, changes the color, can crack. Therefore, the upholstery of the doors emerging directly to the street, vinyl scribbling.

There is, however, a material with increased resistance to UV rays, but it is special material and it is necessary to pay attention to the purchase.

Door upholstery leather: several options

Now about a small confusion in terminology. Dermantin is in its pure form, such as he was in the past century, not done for quite a long time. Instead, there are different types of artificial leather from vinyl.

There are also materials coated from other polymers, but they are not so much. That's all of them in old memory and are called dermatin or leather (although it is right, by the way to say "dermatin" without "n").

So seeing this name, it is necessary to specify which material it is meant, as properties and prices differ significantly.

Despite the fact that the material is essentially one, it has different characteristics and appearance. There are elastic species that are well drawn, there are hard, which is difficult to stretch. In addition, modern artificial leather has many colors and shades, can have a different surface structure:

• smooth - brilliant and matte, there is even with the effect of "metallic";
• porous;
• structured, imitating different types of skin (snake, crocodile, etc.).

  Under crocodile skin

So choosing soft upholstery materials for the extensive door. Apparently, this is the determining factor in the popularity of this type of door upholstery.

Tight upholstery materials for doors more, although they are used less often:

• mDF panels from 8 mm thick to 18 mm;
• natural wood - fragments, array;
• veneer;
• laminate;
• plastic;
• postforming.

Of all this list, most often the doors are separated by lining / MDF panels. This upholstery is especially popular for decorating metal doors, including self-made. The panels are manufactured in size of a particular door leaf, after which they are installed on glue or mounting foam in fixed starting strips. In this case, it makes sense and discarded from MDF.

From the catalog - options for MDF lining, and all this is still in different colors ...

Practically also passes the plating the door with other materials - laminate, plastic, post-forming. On the perimeter of the door, starting profiles are installed, in which the fragments of the finishing are inserted. Everything is simple, in the presence of elementary skills of working with a drill, saw and hammer, you can make it yourself in a few hours.

Dermantine doors upholstery

The most popular way of plating the door - with the help of artificial leather. Such a department allows simultaneously with improving the appearance to increase the indicators of heat and sound insulation. But this type of door upholstery and cons is the most complex technological process that requires at least general ideas about the procedure for action.

Outcome methods

Speech will go about the upholstery technology Dermantine. You can attach it in two ways: with a roller around the perimeter of the door canvase and without it. Depending on this, the procedure is changed (a little later).

Upholstery Dermantine doors - with a roller and without it

Examples of drawings for upholstery doors Dermantine

For the redesign, you can use the same material that the doors have crossed. It is cut into a strip of 2.5-3 cm wide, attached to the upper nails, and then stretching and fixing for the next nails, form a pattern.

To secure the strip it, it can be wrapped around not until the end of the driven nail, which is then clogged. But this option is suitable if decorative nails have large hats.

If the hats are small, the strips are nailed.

Also, the drawing can be formalized using a thin metal flexible cable, but it is harder to fix it - it bends worse.

How and how to fix the dermatin to the door canvase

If the upholstery of the wooden door is needed, the questions usually do not occur - they are attached to the brackets from the stapler, on the contour then nailed with decorative nails. Only here there are nuances: staples should be with a wide back (not less than 1 mm), and nails are bulk, with a wide hat. Fastening installation step - from 2.5 to 7 cm, optional.

Most often wallpaper nails

More questions arise when it is necessary to cover the Rutan iron door. Here the output is only one - perch on glue. The glue is usually used by the "moment", but you can be any other universal that can be glued and metal and leathes.

They lubricate the nickname from the inside (bar, which goes around the perimeter of the door and closes the interface with the door frame). When fixing the vinylisms, it is cut out with a margin of 15 cm, just for the bending on both sides on the wrong side.

Materials for heat and noise insulation

Most often used for the insulation of the door of the foam rubber. It is inexpensive, if desired, allows you to form a bulk convex pattern. The most common case is two layers of foam rubber 1 cm.

This option is not the best - the foam rubber almost does not affect the sound insulation properties of the door, namely, this is sometimes very important.

In addition, after 3-4 years, it loses her elasticity, it starts sticking out, it is necessary to make a doors to do, although the appearance of the leatherette is still quite decent.

All this is so, but there are no worthy competitors for the foam rubber. There are materials with certain properties that can be put instead of one of the layers, and the second will still be foam. For example, "isoton" can be used to improve sound insulation properties.

It is used for the heat-insulation of cars. Sold by small sheets, an adhesive composition is applied to the back side, protected by a polyethylene film. So there will be no problems with installation. Of the minuses - the price and fairly large weight of the material.

In order not to have problems, it is worth replacing the loop to more powerful.

Materials for noise-heat insulation doors

There are two more material used in the automotive industry, with similar properties. It is "splen" and "vibro filter". All of them are made on an adhesive basis, can be used to improve the characteristics of the door.

How to beat a wooden door

It is more convenient to work on the doorned, but if this is a problem, you can knock on the spot. First you need to remove all the accessories from the door cloth - locks, latches, door peephole.

If there is an old upholstery, it is neatly removed. If part of the door requires repair, damaged fragments are removed, replaced with cut-made wooden.

The slots can be smeared with putty or tinted by mounting foam with a small expansion coefficient.

Options

If there was a drawing on the upholstery, and he basically suits you, to the places where the forming drawing of nails were driven, drive the usual. They are not scored not to the end, the hats should be stitching by 1-1.5 cm.

With their help, then vouch in the right places, foam rubber and upholstery (just put pressure with your fingers, all layers are sold). Ordinary nails pull out, install decorative on their place, using a tape form a drawing.

The procedure is simple.

That the end of the door look at no worse than the rest of the plane, starting with it. If one of the parties are not going to separate, this stage is missing, just paint the paint end in the tone of the finish from one or the other side.

If you cut the doors from two sides, we cut the material strip of a width of about 10 cm. More precisely, look at your door, as the thickness of the canvas is different. The band should close the end and go on one and the second side by 3-4 cm.

Strip stack, fasten on the edge of brackets from the stapler (faster and easier) or nails with a large flat hat.

Breeping strip on the end

To form a roller, the material is also needed. Width - 10-15 cm depending on what width you want a roller. Next there are two options:

• Immediately form a roller. To do this, in the middle of the strip laid the harness from the foam rubber or batting, it is crimped in the middle. This form is fixed around the perimeter of the door. After, top, the foam rubber and the material is stacked. To form a neat edge, the material is seduced inside.

  The roller is formed immediately, in the finished form is attached around the perimeter of the canvas

• The roller is formed later, after the vinyl is laid on the canvas. Here the technology is different - the strip is attached around the perimeter, the front side down. Then the foam rubber and the upholstery material. The edges are not converted, they are simply cut into size. After the end, the band turns on the front side (it is possible to put a strip of the foam rubber), begins and fastened by bulk nails.

  The strip for the roller is fixed in advance, it is formed after the upholstery material is fixed.

The difference between these two ways is only in appearance: in the first case, nails are nails on the edge of the upholstery (in the photo on the right), in the second - on the edge of the roller (in the photo on the left). Choose someone else like it. For example, it seems to me that the first option (right) looks better - more neat. But this is only a personal opinion.

Two rolling formation options

What do you need this roller? In order to overlap the possible gaps between the web and the jamb. Thus avoid the appearance of drafts and reduce heat loss.

But it is possible to make a roller only if the doors on the opening side are hurt (the doors open inside the apartment, then from the inside and we are upful of them). If on the other hand, this focus will not pass - it will not cling.

Then you have to do without roller.

Without roller

In this case, everything is simple: the canvas is exactly separated, fixed with nails or brackets - who is more suitable.

Without roller

Door upholstery process in photo-format

To reduce the level of noise, the doors are hurt by one layer of noise insulation and one - foam rubber. A variant with pre-making roller is selected. At first they removed the old fittings, cut a new castle. The lining and the handle were removed, the internal parts remained in place. We proceed to the upholstery of the doors.

Immediately form a roller - in the Dermantine strip we are laid a narrow foam rubber, fastened around the perimeter of the door. Make it more convenient to braces from the stapler.

Nail roller around the perimeter

The next step is both soundproofing. It is on adhesive basis, so there are no problems - cut out in size, gently removing the film was glued. By gluing, we try to squeeze all the air, for this, the film we grip gradually, stroking the material from the edge to the edge.

Adhesive sound insulation

Now foaming is a thickness of 1 cm. In this embodiment, the most convenient way is the staples from the construction stapler. First, fasten around the perimeter, then often - on the surface of the door, so that the foam rubbed is tight.

We are placed and fastened foam

The foam rubbing with a slight margin, after mounting the surplus is cut.

The upper edge we add to 2-3 cm, starting starting from the left upper angle. They score the first nail there, then we put the material and nail the second above the right. Then, with a step of 3-4 cm, nail the upholstery from one edge to the other with finishing nails.

Having turned on the top edge, kpripim it

Crepim from the loop, having turned the edge inside. Place smoothly so that there is no chances at the top.

Nail from the loop

After the same operation is repeated from the castle, then below. Actually, the upholstery of the doors is almost over, you just need to install accessories in place.

Install the pads of locks and accessories

- Turks on the topic

Vinilisor for the upholstery of the door is sold both on meters and in sets. In some sets, the fastening method may be different: they have plastic profiles that are attached around the perimeter of the door leaf. These profiles have a fixation system by type that used in stretch ceilings. How to beat the doors in this case, look in the video.

The following video captures a process using a roll material.

How to insulate and enjoy the entrance door. The technique of forming a roller of the second type - it is nourished last.

How to hammer metal doors

The facial part of metal doors is rare - it also has a completely attractive appearance. The inside suffers more often. That's about it and talk.

On the iron door on the inside there is a frame in some models it is metal in others - wooden. The heat-insulating material is placed between frames of the frame. It can be a foam or mineral wool slab. They are attached to the mounting foam, having a very small expansion coefficient (required!). From above, everything is closed with a sheet of plywood or OSP.

This is a standard option. If the planks are wooden, everything is fine, there are no problems - no doors will not be freeze. But if the frame inside the door is metallic, with good frosts, everything is frozen through - through the bridges of the cold, which are metal ribs.

So that this does not happen, on top of the foam / mineral wool it is stacked again, the layer of "isotone" or "splen", and they are already Faneru.

The remaining processes in the upholstery of the metal door are very similar to those described above. All difference - in the method of fixation: the upholstery is glued to suitable high-quality glue. Surplus is immediately cut off at the place of the joint, using a sharp wallpaper knife.

Here it is just a classic error - there is no layer cutting off the cold bridge. Otherwise, everything is shown not bad.