Rolled insulation: species and features of rolled insulation. Features of rolled heat-insulating materials Roll insulation

Rolled insulation - This is the name of a whole class of lightweight heat insulation, widely used in civil and industrial construction. They are made from staple fiberglass with the addition of various binders, fillers, hydrophobizers (substances that repel water), which give them softness, elasticity and elasticity. Rolled thermal insulation is the most inexpensive of all types of insulation, therefore, it takes consistently high demand from builders.

This section of the site presents rolled insulation, the price of them and roll parameters. All information about products from different manufacturers is given on one page. Here you will find a brief description of each of them.

Stamps of rolled URSA insulation / URSA

This line of insulation includes stamps:

Rolled fiberglass insulation URSA GEO M-11 (roll 10000x1200x50 mm x 2 pcs)
Rolled fiberglass insulation with foil URSA Geo M-11F (roll 18000x1200x50 mm)
Roll Fiberglass Heater with Foil URSA Geo M-11F (roll 9000x1200x100 mm)
Rolled fiberglass insulation URSA Geo M-15 (roll 8500x1200x50 mm x 2 pcs)
Roll Fiberglass Heater URSA GEO M-25 (roll 9000x1200x50 mm)
Roll Fiberglass Heater URSA GEO M-25 (roll 4500x1200x100 mm)
Rolled fiberglass insulation with foil URSA Geo M-25F (roll 4500x1200x100 mm)
Rolled insulation on the acherov binder URSA Pureone 37RN (roll 10000x1200x50 mm x 2 pcs)

This is a very well-known line of insulation of the European manufacturer - the concern "Uralita". Roll insulation of URSA brand are soft elastic mats from staple fiberglass. Each brand has its own marking that allows customers to easily navigate in the characteristics of the material and, accordingly, in its purpose. URSA insulation are high-quality light heaters recommended for use in horizontal unloaded building structures. Good heat engineering characteristics, the ease of transportation and installation make them the most demanded over the years.

A special place in the line of roll insulation of the URSA concern is occupied by the insulation of a new generation under the brand name Ursa Pureone (in rolls and stoves). As a binder component, acrylic is applied here - neutral and safe polymer. The production technology of these insulation eliminates the use of phenols and formaldehydes, which causes their special environmental purity. They are widely used in Europe, America, Japan for heat and sound insulation indoors. In Russia, they also acquired deserved popularity.

Stamps of rolled insulation KNAUF / KNAUF

Rolled Heat Heat Heat Knock Dacha (7380x1220x50 mm x 2 pcs)
Rolled Heat Heat Heat Scoop Cottage (6148x1220x50 mm x 2 pcs)
Rolled Heat Heat Heat Heat Knauph Insulation NH 040 (7380x1200x50 mm x 2 pcs)

These are natural mineral wool insulation, made on the basis of innovative ECOSE technology. In the process of manufacture, binders are used on the basis of natural components, therefore, it has a pleasant color of natural flax, and a pleasant to the touch structure. Due to environmental purity, such insulation can be used indoors.

You can always contact our specialists who will prompt you where you can find additional information about the insulation you are interested in or will be given tips on the installation of material.

Properties of rolled insulation

All roll insulation have about the same properties that determine their widespread use, namely:

low thermal conductivity;
good sound insulation;
optimal hygroscopicity;
high water repellent indicators;
ease of transportation and operation;
resistant to the effects of aggressive media (acids, alkalis, solvents);
fire safety;
optimal price.

If they are used to insulate the pitched roof, which has a frame carrying system from a tree or metal - the insulation is stacked inside the frame. When working with rolled insulation on vertical and inclined surfaces, it is necessary to use a crate or framework. The insulation is mounted with support for overlapping "cold bridges".

Where to buy rolled insulation

Roll insulation can be bought:

wholesale and retail on our warehouse complexes in Moscow;
order delivery to the object;
combine all the materials in the same team machine that will deliver them to the object;
order Wholesale delivery with free shipping

We cooperate with individuals and organizations from all regions of Russia. Check out the catalog and make an online order on our website. Our managers will answer all questions about the conditions of cooperation by phone from the section.

Buy in one place save on delivery, use discounts of regular customers

The rolled insulation is a material with a small thermal conductivity indicator, which is additionally characterized by sufficiently low rigidity, but it has a good form. The coverage of this species is flexible, which allows the finishing of the plots of a complex configuration. Stop such a material is easy. However, it is important to choose the right dimensions. The insulation in rolls is attached to the jack, it is unacceptable to leave substantial gaps between the adjacent areas of thermal insulation. This will lead to the formation of cold bridges.

The material of this species is universal, which is due to the properties (low rigidity and density indicators, flexibility). It means that it can be used at the facilities of different targets (private, economic, public, etc.). However, it should be remembered that each of the types of such a material may have both restrictions on use, for example, if it does not meet the operating conditions. Rolled insulation is suitable for mounting on horizontal and vertical surfaces. It is tight enough to keep the shape.

A coating with a metallized layer is mounted on objects and surfaces, where it is important to ensure the highest level of protection against heat loss: in the baths, saunas, when installing water / electric heating floor, etc. The desired effect is achieved due to the presence of a heat transfer layer.

Rolled insulation - the only price-available materials that are suitable for protecting complex surface configurations: with drops in levels (stepwise), bends, joints, hard-to-reach places. This feature is due to flexibility and low rigidity.

Directions for the use of thermal insulation of this type:

wall covering outside and inside under the decorative finish of any species (rigid plates, soft materials and even wallpaper);
floor protection, in this case, the heat insulation roll is protected from the deformation of the crate;
warming of flat / pitched roofs;
reducing heat loss through the overlap;
protection of pipes of different targets.

Types of materials in rolls

Two groups of insulation, characterized by flexibility, low density and rigidity are distinguished:

Based on polystyrene foam, polyethylene. Such materials are characterized by a closed-powered structure, which is achieved by foaming raw materials. As a result, most of the volume is a gaseous medium. When foaming polyethylene, a flexible coating of a small thickness is obtained. The rolled insulation of this species is characterized by low thermal conductivity, wear resistance, serves as long.
Mineral wool is represented by varieties: glass and slag, basalt or stone wool. These are natural insulating coatings characterized by low thermal conductivity. The disadvantages include low strength, a tendency to send during operation, hygroscopicity. The last of the properties is the cause of the short-term coating period. This insulation is suitable for walls, floor, overlaps, attic, basement, roofs. If we provide protection against moisture in areas with elevated loads, the coating deformation can be avoided.

Foamed insulation are divided into types of differences in the method of production:

physically sewn;
chemically stitched;
gaspen.

The first 2 options are characterized by similar properties, but are manufactured by different technologies. In addition, insulation are divided into types with regard to the differences in structure: foamed with additives (antipirens), foil. The last options are characterized by improved properties. It not only reduces heat loss, but also reflects the thermal radiation, returning it back to the room.

Steklovat

The basis of the material is the waste of glass industry, sand. Raw materials are exposed to high temperatures (+ 1450 ° C). In the process of melting, the finest fibers appear. To obtain thermal insulation material, a binder is added, by means of which fiberglass glued. Then the formation occurs. For the binding component to receive the desired properties, it must pass the polymerization process. At the last stage, the material acquires a yellowish tint as a result of staining.

The heat insulating layer of this species protects different types of objects. Glasswater - universal coating option. However, in the work with it you need to use personal protective equipment (respirator, glasses, gloves, closed clothing). This is due to the fact that the insulation contains particles that are characterized by a small mass and can be released into the environment under the influence of external factors. Dust enters the respiratory tract, settles on the skin, mucous membranes than provoking the irritation of fabrics.

To slightly improve strength indicators, rolled material reinforcement. The disadvantages, in addition to the release of abrasive particles, are relatively low thermal conductivity. For this parameter, the insulation loses foamed counterparts. Another minus is hygroscopicity. The overwhelming majority of mineral coatings absorb moisture.

Advantages Glasswater:

good sound insulation properties;
sufficient level of strength;
the material is lightweight, and therefore will not be weighting the design;
installation does not require special skills;
flexibility;
vapor permeability;
fire safety;
elasticity, so that the insulation can restore the initial shape;
a small width, which means, glass gamble will not english space;
resistance to mold formation, fungi;
the insulation is unattractive for rodents.

When choosing, not only positive / negative qualities, but also the coating parameters are taken into account. Glasswater is characterized by the following properties:

the thermal conductivity value is in the range of 0.039-0.047 W / (M * K);
water absorption coefficient glass gambles with incomplete immersion - 15%;
the insulation of this view is operated at a temperature of -60 ... + 250 ° C;
when contacting water in the first day, the coating will absorb water in an amount of 1.7% of the total volume of thermal insulation material;
sound absorption indicator: from 35 to 40 dB.

In terms of thermal conductivity, the glass gamble is similar to such insulation: mineral wool, polystyrene foam.

Isolon

It is foamed polyethylene foam, which is characterized by a closed structure. It is proposed in such varieties: simple, with a foil layer from one or two sides. Isolon is quite dense, but at the same time a soft insulation. His characteristics:

the average thermal conductivity is 31 W / (M * K);
density - 33 g / m³, with a decrease in the value of this parameter, the thermal conductivity is growing;
the coefficient of water absorption is 1%, which indicates the absence of the inclination of the insulation to absorb moisture;
the material does not miss steam;
the ability to perform its main task (reducing the intensity of heat outflow) at low temperatures - to -60 ° C, while the insulation does not lose properties, it does not break, not deformed;
the duration of operation is about 100 years;
there is a resistance to negative factors: precipitation, high loads;
when burning, poisonous substances are not distinguished;
the material is environmentally friendly;
the insulation isolon protects the object from noise, and the reduction in the intensity of the sound waves is noted even with the minimum thickness of the material.

If we consider the foil coating, then its ability to heat recovery should be highlighted. The insulation reflects 97% heat back to the room. Isolon is not amenable to deformation. It is understood that under the influence of moderate loads, it retains properties.

Plates in rolls

In this case, we are talking about materials with increased rigidity that are formed into rolls. These include basalt cotton wool. This material is characterized by a fibrous structure, exceeds glass gamble in terms of hygroscopicity, thermal conductivity. In addition, basalt wool in density rolls is almost no different from the isolon (30 kg / m³). The thermal conductivity of the material is 0.039 W / (M * K). By the water absorption coefficient, the insulation is inferior to foamed counterparts (15%). The main advantage of such a coating is the inconsistency of the burning.

Table of rolls of rolls

For comparison, insulation is taken, the thickness of which does not exceed 50 mm. This is due to the fact that more massive rolled thermal insulation materials are much worse than collapsed. Fibrous coatings are involved in the review. Manufacturers of heaters in rolls:

To compare coatings at cost and determine the most suitable option, take into account the number of strips in the package.

conclusions

Roll thermal insulation in many cases is preferable, since it is characterized by flexibility. In addition, the material of this group differs in low thermal conductivity, which allows it to be used in order to insulate the object. However, it should be borne in mind that fibrous rolled coatings poorly tolerate contact with the liquid, so you need to carefully protect them using waterproofing.

If you plan to apply foam insulation, it is important to remember that they do not miss steam, which means that the microclimate indoors may worsen. To avoid negative consequences when installing insulation of this species, it is recommended to establish a supply and exhaust ventilation or increase the efficiency of natural air circulation in the room.

With the insulation of large sections, no isolation plates show better efficiency, and rolls with insulation. The same applies to pipes and ventilation channels. Their main difference is an increased density, and a consequence of this - high coating rigidity, which makes it much better to insulate objects with non-standard geometry.

Features of species

There are several varieties of insulation, they are mainly divided according to the composition.

Minvata.

One of the most common in the Russian market is thermal insulation material based on mineral wool. This is mainly due to the combination of the price and the technological properties of the material itself. It is very easy to operate. It is advisable to choose white, soft and self-adhesive material for a bar.

The name "mineral wool" is inherent in the set of thermal insulation materials that are different in their composition and properties. The insulation is not particularly popular, which is made by smearing some rocks with the formation of certain fibers. In the manufacture of these fibers are spilled into a single carpet, this wool is called "basalt". For any resident of Russia and the CIS sign and the term "glass gamble".

This thermal insulation matter is outdated technology, but because of its price, it is in demand today. It is made by mirroring the broken glass into single fibers. There is also a wool obtained in the process of overcoming the waste of the metallurgical industry (slag).

Due to raw materials, which is used in its manufacture, its price is much lower than that of glass gambles or basalt wool.

Characteristics, pros and cons

Wat differs from each other with technical characteristics. The glass gamble has a high temperature threshold of 450 degrees, after which the material acquires irreversible destruction. The fiberglass density is 130 kg / m3, and the thermal conductivity is about 0.04 W / m * p. This material is not a flammable, it does not tweet, has a high threshold of vibration and sound absorption.

Over time, there is practically no shrinkage, including options with long-term operation.

By cons can be attributed to the fact that when water enters, all the positive properties of this material are coming. Glasswater is a rather fragile and brittle material. When contacting the skin, it causes irritation, itching, which is problematic to withdraw.

When entering the organs of vision, it can seriously harm them, as well as when hitting the nasopharynk. Working with such material is needed in closed clothes.

Basalt wool withstands a large temperature (up to 710 degrees). Its thermal conductivity is about 0.04 W / m * C, the density varies in the range of 210-230 kg / m3. Unlike the glass gamble, this material is not afraid of moisture, and also does not lose its properties. If you get on the skin, the rolled insulation does not cause irritation or itching.

The largest mass and density is slag. Its density fluctuates in the region of 390 - 410 kg / m3, and the thermal conductivity is about 0.047 W / m * p. However, the temperature maximum is much lower (about 300 degrees). Slotovat melts, in the process of melting, its structure is also destroyed, and irreversibly.

The dimensions of these materials vary, they depend on the installed manufacturer standards. However, the most common are:

length from 3 to 6 m;
the width is standard 0.6 or 1.2 meters.

Some manufacturers make other sizes in width (0.61 m). Wool thickness standard (20, 50, 100, and 150 mm).

Foil Material

Often, one of the sides of the insulation is covered by a layer of foil material. This allows you to keep the coating from moisture exposure, ultraviolet rays. Most often, such materials are used with internal insulation of premises, the wool itself can be absolutely any. Types of such material are diverse. These include expanded polystyrene, cork, polyethylene.

The main most popular material material is polystyrene foam. He is very practical and inexpensive. Perfectly copes with sound insulation and vibration. Roll length is usually 10 m, the width does not exceed 0.5 m. This material is perfectly coping with moisture and fungus. However, according to the degree of thermal insulation, it is significantly inferior to foam polyethylene.

For thermal insulation, the plug is characterized by high strength, low weight, harmlessness and not bad appearance. For wet rooms, it is recommended to use cork flooring with wax impregnation. The dimensions of this material are the same as the polystyrene foam. Pretty good material is foamed polyethylene. It is small cells with air, on the edges there is a cardboard or paper.

The substrate is fixed by lamination. Due to this, it is possible to achieve the most durable and reliable connection with any type of base. The rolled insulation is characterized by good heat-conducting characteristics. Depending on the purpose there are foil and metallized coatings.

For steam output, a foil type of material is more suitable, a metallized spraying is necessary for steam out.

Sputtering is very fragile and damaged from small mechanical impacts. Foil material has excellent heat-reflecting characteristics. It is less susceptible to mechanical damage. Today, silver material with a reflector is quite popular.

Manufacturers and selection criteria

One of the leading companies for the production of rolled insulation is the German firm Knauf.. A distinctive feature of products is the lack of formaldehyde. In addition, materials are characterized by simplicity in use. This company practically each roll provides installation instructions, which will allow novice builders to make work on insulation better. Due to the composition in such thermal insulation, insects (beetles, ants) and rodents (rats) will not be able to settle.

The French brand is not least well known Isover. This company has a huge selection of roll-type insulation. Foil Rolls are also available. The products of this company are used for insulation of indoor rooms, as well as outside buildings.

Due to its composition, it is a refractory, in a fire or brief ignition, does not support the burning and independently fades.

The Spanish company is most common in the European part of Russia URSA.. Its products are somewhat cheaper by the French brand, the range is not inferior to her, which makes the materials in demand in the buyer's environment. The company gives a very long warranty on their products, the exact figures of the warranty are better to specify immediately before purchase.

The cheapest insulation produces a domestic brand "TEKHNONIKOL"which is focused on middle-weight people. The quality of this material is incomparably with foreign analogues, but the insulation is very popular with people engaged in its own construction of cottages or private houses. Due to the price, it is a favorite thermal insulation from managers and other organizations that want to do something voluminous for little money. It has its own quality and minvat "Warmhouse".

When buying it is important to remember that various insulation is needed for different types of premises, as the ceiling isolation is extremely undesirable to use on the floor (and vice versa).

Wall insulation has its own characteristics, because the appointment of each type of isolation is slightly different, as well as properties. Some moments depend on the material of the structure on which the rolled heat insulation is attached. It is necessary to see how moisture is affected by the material to take into account this when choosing.

Montaja technology

Technology installation of the roll insulation is slightly different from the plates. Start warming the original walls or gender. The walls are mostly made from the plates, like a straight ceiling. Therefore, often the floor and scope ceilings are suitable for insulation and installation. When insulating floor it is worth seeing exactly what kind of insulation is available.

The insulation in foil is used mainly, but sometimes the heat roll rolls are coated with a conventional thermal insulating foil or metal film. From the walls, the insulation should be 1 cm. This is due to the fact that when changes in temperature change, the material is compressed and expanding. The absence of free space in a metallized or folgized insulation leads to its deformation and damage with time.

Ceiling (scanty) insulation fasten between rafters, cutting a little more to insert better between the boards. Insert them strictly bottom up to avoid emptiness. After installation, the surface is clamped with the main profiles or boards for applying additional (for example, vaporizolizing) materials. Work is carried out especially carefully.

The replacement is not always convenient and functional thermal insulation plates comes an improved version of thermal insulation - a rolled insulation is equally effective for both walls and ventilation channels, pipes, roofs and other surfaces. The material is characterized by improved technical parameters and, unlike mineral wool in stiffery and density plates, allows it to be used for elements with a complex geometry.

The insulation is distinguished by high operational and technical characteristics, is implemented at an affordable price. The rolled insulation is used both in the repair and overhaul to increase the thermal insulation properties of surfaces:

basement;
attic;
balcony;
floor;
overlaps, etc.

Standard Roll Insulation based on Minvati under wallpaper on the walls in the residential room allows you to increase the temperature by several degrees by reducing heat loss.

Additionally, the material prevents the development of dampness, the appearance of fungus and mold, and if there is an uneven surface - hides the flaws without additional work.

The wide range of mineral wool in rolls allows us to talk about its versatility. The material is almost indispensable in modern areas of construction, it allows you to create a truly working and durable layer of thermal insulation both in apartments and houses and in economic buildings, in enterprises, saunas, baths, etc.

Especially important is the ability of the material to contact with pipes and surfaces of ventilation mines. In this case, the rolled insulation is arranged primarily due to the elasticity and flexibility of the material. Rolls are convenient to use, make it possible to separate uneven surfaces, including at minus temperatures.

The advantages of thermal insulation in rolls

Comparing the rolled insulation with conventional mineral wool-based plates, the benefits of the first are obvious. These include:

Minimum thermal conductivity indicators including among budget models.
Resistance to atmospheric phenomena, temperature jumps, rodents and microorganisms while preserving the main thermal insulation properties.
A wide selection of material based on different types of mineral wool for insulation of surfaces with different operational characteristics and features.
Resistance to high temperatures (up to 700 degrees Celsius), open flame.
Noise-canceling properties, which makes it possible to increase the level of heat and sound insulation.
Convenience of mounting.

There is a rolled insulation based on mineral wool and a small disadvantage - high steam conductivity, which will require a layer of vapor barrier.

Types and characteristics of thermal insulation in rolls

At the heart of the insulation in the rolls of mineral wool, which can be represented in several versions:

in the form of basalt wool;
glass gaming;
slag.

Materials based on basalt wool are created using rock solid technology with formation on their base thin, woven into a single carpet breed.

For the manufacture of materials based on the glass gamblers, we use melted glass battle, which makes it possible to significantly reduce the cost of finished thermal insulators.

For thermal insulation in rolls based on slag, used mainly waste from the metallurgical industry. Compared to insulation based on the above described insulation based on basalt wool and glass gamble, it is the cheapest.

For each of the mentioned thermal insulation materials, its set of characteristics is characteristic, despite the fact that they are all improved version of mineral wool. So, for example, a fairly resistant to high temperatures is glass gamble. The heat insulator is able to withstand up to 450 degrees Celsius, with an increase in temperature above the specified mark, the surface is destroyed and not subject to recovery.

Materials based on glass gambles are the greatest density and thermal conductivity. Rolls are not combustible, do not smooth, perfectly copble with vibrational manifestations, suppress sound oscillations and what is important - do not give shrinkage regardless of the duration of life.

Of the minuses based on fiberglass wool, it is worth noting instability to moisture, as well as unpleasant consequences arising from contact with human skin.

Thermal insulators based on basalt wool in rolls withstand high temperatures up to 700 degrees, have excellent thermal conductivity and density indicators. In contrast to thermal insulators based on fiberglass wool, the materials are able to withstand moisture while maintaining the main performance characteristics even after wetting. Heat insulators belong to the group of environmentally safe materials that are not able to cause allergic reactions.

Slotovate - thermal insulation for insulation of surfaces, the operating temperature of which will not exceed 300 degrees Celsius. The density of the materials reaches 400 kg / m3, thermal conductivity ranges from 0.046 to 0.048 W / m * p.

The temperature exceeding the specified limit will lead to melting slag with the destruction of the structure. Depending on the manufacturer, you can select materials for thermal insulation based on slag wool with suitable parameters: length - from 3 to 6 m, wide - from 0.6 to 1.2 meters, thickness - from 50 to 150 mm.

Heat insulator with foil surface: features

Folgized thermal insulation materials have one main feature - side with a foil layer intended to reduce the impact on the surface of ultraviolet rays and additional protection against moisture. Use materials for insulation of surfaces indoors with the basis of different types of wool.

It is necessary to work with foil thermal insulation by special technology, observing some nuances, for example, not forgetting about a small gap (no more than 1.5 cm) between finishing and thermal insulation material. This is important, since when increasing the temperature, the insulation will keep the temperature, passing it on the back wall, returning back to the walls, but not to the room, as is necessary.

Another important nuance - in contrast to insulation in rolls based on basalt, fiberglass or slag wool, the foil insulator is mounted on the crate, placing the brass and processing the joints with insulating material.

Tips for choosing heat insulation in rolls: what you need to know

Summing up all of the above, it remains to note several important nuances in relation to the choice of materials based on mineral wool roll type for insulation. Experts recommend first to take into account the type of surface and purpose. It is necessary to select materials suitable for thermal insulation of certain surfaces: wood, concrete, brick, etc.

It is not necessary to write off from accounts and the thickness of the base, taking into account the temperature indicators and atmospheric precipitation in the region, especially when it comes to outdoor insulation.

Buying materials for thermal insulation based on any of the listed types of watts, it is worth paying attention to the integrity of the packaging. It is strictly forbidden to make moisture on the material in the package.

Each of the types of insulators listed above has its own characteristics, advantages and disadvantages, so the choice should be done after careful analysis depending on the required functional.

How do you look at the perspective to reduce the cost of home heating by almost a third? We think this is the case when comments are too. It is realistic to achieve a similar result, just correctly choose the heat insulation for the roof.

One of the most common thermal insulation materials is considered to be Minvat, in particular, in the form of mats. However, when it is to be warmed, for example, large areas such a solution is ineffective. For such cases, the rolled insulation will be held.

All materials of this type have about the same advantages that their high demand is explained. We are talking about their qualities such as

low thermal conductivity
good sound insulation
optimal hygroscopicity
high water-repellent indicators
chemical stability
fire safety.

And this is not the entire list.

Rolled insulation, due to its elasticity and flexibility, easily restores the form, is suitable for work on uneven surfaces. There is no temperature limit, because it retains its operational characteristics at extreme temperatures.

Scope of insulation in rolls

It is successfully used for roofs and basements, floors and ceilings, pipes and the other. The thermal insulation device from this material is a fairly simple process. Moreover, work can be performed independently, without attracting additional labor. Therefore, this type of thermal insulation has gained great popularity in private construction, in particular, baths, household buildings, etc.

Types of insulation

In a separate group, materials having a protective layer of foil are isolated. In terms of cost, they are somewhat more expensive than the rest, but have a lot of additional valuable properties.

The foil itself does not have a thermal conductivity needed for insulation, however, it effectively retains heat due to the ability of the reflective surface not to skip the infrared rays out of the room. It is worth noting that at the same time she does not allow them to penetrate outside. The latter is quite useful quality for roofing isolation, especially in a hot summer, when the roof under the influence of sun rays is very warming up.

Insulation, rolled folgized allows you to maximize the length of the material, that is, it is placed from one entire strip, which is extremely important for its effectiveness. . These include foamed rubber, polyethylene and other materials in roller execution

These materials do not hold form and easily turn into rolls. They are effective enough, it is easy to work with them. Unlike foil thermal insulation, they are used in combination with vapor barrier, which creates an ideal tandem against the cold.

These include foamed rubber, polyethylene and other materials in roller design. These materials do not hold form and easily turn into rolls. They are effective enough, it is easy to work with them. Unlike foil thermal insulation, they are used in combination with vapor barrier, which creates an ideal tandem against the cold.

This is the most common type of insulation. Many consider such a form of packing to be optimal, because with this approach, long strips of the insulator occupy a small volume. Most often, the beams of overlaps or mounting profiles are installed in a step equal to the roll width. It extremely simplifies the installation: first, the material is simply spread over the surface and secured, secondly, the extra seams are not formed.

Manufacturers Review: Eau return, Knauf, Urs

How to choose the right rolled insulation for roofing How to choose a rolled insulation. Varieties of the rolled insulation. What are the advantages of a rolled foil insulation. Characteristics of rolled

Popular manufacturers

Products are presented in the market of various manufacturers. Each trading mark has its own characteristics and advantages.

Knauf.

The German manufacturer offers material, which does not have formaldehyde. Knauf products are safe for people. Mineral wool does not cause allergies, but its laying should be performed in gloves. Microscopic fragments included in the insulation can cause skin irritation.

Knauf rolled materials are not interested in insects and rodents. In addition, it is capable of protecting from external noise due to good sound insulation characteristics. Different with low thermal conductivity and good breathability. The company offers materials to protect walls, plates, pipes and other surfaces at dachas and country houses.

Faith

Insulation, characterized by high density. The French manufacturer offers products of various thicknesses: from 20 to 150 mm, which significantly expands the possible area of \u200b\u200busing the heater "RUB".

The company's catalog contains heat-insulating material with foil, which is often used to insulate the pitched roofs, walls, ceiling, warm floors, not only in homes, but also in baths and saunas. In combustion corresponds to the first class.

Ursa

Quality professional insulation with a long service life. It has excellent sound insulation characteristics. Does not burn. Under the influence of the flame does not secrete toxic substances. When installing it does not break, it does not crumble. Pleasant to the touch.

When the walls of private houses are insulated, M-11 is most often used. When performing thermal insulation works in the industrial complex, preference is given to P-30.

TOPISOL.

The insulation may have a thickness of 3 - 20 mm. Suitable for various climatic zones, including regions with high humidity. Does not rot. Differs good vapor permeability. When providing sufficient tightness of the seams is able to withstand the streams of the wind.

Used to protect the walls, roofs, including attic, floors. It has a low weight, which makes it easier to transport and reduces the requirements for the strength characteristics of the insulated surface. It is capable of maintaining its performance characteristics for at least 30 years.

Installation can be made independently without special equipment.

Penophol

Multilayer foil material, sometimes several types. Type A provides for the presence of one foil layer. At the type in between the layers of high-quality aluminum foil there is a self-tapping polyethylene. Type C is supplied with a special adhesive basis, which greatly simplifies its installation. Type A is characterized by the lowest cost and smallest rigidity.

The thickness of the foil at the foam is 12 - 30 μm with the thickness of the base 2 - 10 mm. For insulation of surfaces working in sufficiently hard conditions, a material thickness up to 40mm can be used.

Environmental, safe, suitable for the insulation of children's rooms.

Scope of the rolled insulation

Rolled insulation are used for thermal insulation of vertical and horizontal surfaces. Foilized material is indispensable for the creation of thermal insulation in bathrooms, since it retains heat well and has heat-reflecting properties. And this material was widely used for thermal insulation of individual structures, joints, in hard-to-reach places.

Consider the main ways to use roll insulators.

Rolled heat insulator for walls

Rolled insulation for walls can be used as thermal insulation material applied under the decorative finish, including wallpaper.

Application technology is very simple:

the self-adhesive material passes on the pre-prepared, aligned and purified garbage and the old finish, the wall;
the layer of the heat insulator is applied adhesive composition based on cement, by the properties resembling liquid plaster;
after pouring the adhesive composition, you can start shook wallpaper.

The use of such a material under the wallpaper will significantly increase the heating stuffing properties of walls, as well as their noise insulation.

Rolled heat insulator for floor

It is used as a substrate for various types of decorative flooring. It has not only heat-insulating properties, but also gives the "softness" floor, eliminates the screens and sounds during shrinkage and movement of the floor covering.

In some cases, a foil heat insulator can be used for thermal insulation of the floor, it will increase the maintenance of heat, however, the cost of materials reinforced by foil is 30-60% more expensive.

The technology of production of work insulation work with a foamed polymer in rolls is very simple:

the material is glued to the wooden floor or concrete tie with the help of adhesive composition or self-adhesive properties;
runs so that there were no "bubbles";
from above the floor covering.

The advantages of such thermal insulator include simplicity of installation, lack of garbage, durability and environmental safety. When choosing a rolled heat-insulator for a floor, you should remember that than "softer" flooring, the insulation must be densely.

In other words, the linoleum is better to use a polymer with a maximum density, otherwise, when walking, you will "drown" in the outdoor surface, but the polymer with any density can be treated under laminate or parquet.

Rolled heat insulator for roofs

Suitable for thermal insulation of pitched and flat roofs. The roof insulated with such material will be warm for several decades. It is possible to lay thermal insulation by our own, without attracting highly paid specialists. The thermal insulator is located between the elements of the rafting roof system, and the displacement, the formation of waves and other defects are not allowed.

In some cases, for example, when insulation of a residential attic room or in the regions with a cold climate, it is recommended to lay a heating polymer in two layers.

The technology of work on the heat insulation of the roof depends on the design features. The best option when thermal insulation is designed at the design stage. In this case, the work is reduced to the fact that the rolled material is rolled and glued to the inner surface of the roof, it should be sharpened by a layer of vapor barrier material and the final finish is equipped, for example, siding, lining, etc.

Applying rolled insulation

This technology is far from excellence and creates only the illusion of real savings of material resources, since in fact this type of isolation is inferior to such sprayed analogues as a polyurea

Another difficulty is the application technology. Immediately, it should be mentioned that all surfaces must be prepared: carefully cleaned or even washed. Even minor pollution can lead to negative consequences. Self-adhesive isolation is applied like a sticky tape, but the effectiveness of this method is lower. Over time, glue loses its properties, especially under the influence of temperature drops, and the material is peeling. The installed isolation is applied using a gas burner. This is a slow and painstaking process, but the clutch is somewhat better, although there is no guarantee that in some places it will not give slack.

Regardless of whether the rolled waterproofing of the floor will be carried out or any other surfaces, this process takes a lot of time and effort. Accordingly, the deadline for commissioning is delayed. Yes, and this work is expensive. Therefore, this technology is far from perfection and creates only the illusion of real savings of material resources, since in fact this type of insulation in all indicators is inferior to such splashed counterparts as a polyurea.

Advantages and disadvantages

The main advantages of rolled material are:

Universality. Suitable for thermal insulation of any surfaces. For complex spatial forms, including curvilinear, you can cut a suitable piece.
Minimum requirements for surface preparation before laying.
Winning at the price of the material and on the performance of work when insulation of large areas of walls, especially direct sites.

Possess rolled materials and disadvantages.

High laboriousness when laying in a frequent crate, you need extra time for cutting.
Small rigidity does not allow them to apply them where it is necessary to resist significant loads.

In general, advantages compensate for disadvantages, this explains the high popularity of rolled materials among consumers.

Materials are harmless to health, subject to their proper operation and observance of fire regime.

Varieties of rolled insulation

Mineral wool

Produced in several modifications. General drawback - hygroscopicity. All insulation needs to be protected from direct contact with liquids; The difference between them is only in the intensity of its absorption.

Glasswater. Pros: one of the cheapest (manufactured from a glass "battle," the swath), unattractive for rodents, insects (often used when arranging warm floors). Increased density, the ability to extinguish sounds, the inconsistency of the burning add glass advantages in application. Minus in difficulty working with the material. When installing the rolled heat insulator based on glass gambles without means of protection can not do. And not only respiratory bodies, view; Need dense, closed clothing - microscopic glass fractions penetrate literally everywhere.
Slag. It is also based on waste, but the metallurgical industry. In terms of cost, this insulation is comparable to glass gamble (even somewhat cheaper), but in high temperatures resistance loses. But on the thermal conductivity - the leader among the mineral wat. For all other characteristics of approximately one level with other insulation of this group. Cons: absorbs moisture (increased hygroscopicity), poorly shuffling noise.

There is still a disadvantage that makes the use of slags for insulation of metal pipes inappropriate. It is not recommended to be used for thermal insulation due to residual acidity - the steel acts destructively.

Basalt wool. Raw materials serve recycled rocks. Pros: the ability to withstand high temperature (up to +700), optimal combination of thermal conductivity / density characteristics. The peculiarity of the material is that after wetting it does not lose heat insulating properties (although there is a limit of the percentage of moisture), differs in high sound absorption, fires, "environmental" (safe for allergies).

There are few minuses: for this insulation, a high-quality vapor barrier is needed, with time it is flattened.

Any of the listed thermal insulation materials is sold in the modification "Foil". The thinnest layer of aluminum increases the heat-reflecting properties of products, protects it from contact with moisture.

Polymers

All rolled insulators are made on the basis of polyethylene or polypropylene foamed. They differ in characteristics, but taking into account the low thickness of the calendar, the difference in thermal conductivity between them does not matter, therefore they can be considered identical. The most promoted, although not the only representatives of this group of elastic insulation in the market: "Penofol" (PE) and "Penoterm" (PP).

The Russian products are characterized by good reviews under the Energoflex, Energofloor, Jermaflex (combined material) from ROLS ISOMARKET. On the market, it is relatively recently on the market, but judging by the exchange of views on the Internet, perfectly established itself as an effective and universal insulation. Her quality appreciated and experts appreciated.

The main role is assigned to the metallized layer. It is the foil that prevents the passage of thermal rays through the material. It is covered with a heat insulator with one or both sides; The choice of option is determined by the conditions of application.

Choosing the insulation of an unknown brand, you can face the substitution of concepts. To reduce the cost of the cost, individual manufacturers instead of the foil layer are applied to the thermal insulation metallized spraying. Such a screen is not distinguished by durability, and in efficiency significantly inferior to aluminum coating.

So what option is better to choose cotton wool or polyethylene

The main point, which is important to understand this is that the foamed polyethylene or polypropylene in the form of rolls is the heat insulation, that is, the material, the purpose of which slightly improve the characteristics of the walls, and not fully insulate them. Regardless of where it will be fixed - from the inside or from the facade

But basalt wool is already a real insulating layer. True, in the case of applying inside the room, the wall will still be freezing, just heat from the room will be noticeably less.

It turns out that from the inside the focus will give a smaller effect than the cotton, since the temperature will raise except for degrees and a half. And even if you perform an external installation, the "picture" will be the same, but only with one positive point - the wall will be slightly fluid and the condensation from the room will disappear.

At the same time, the material has indisputable dignity - it is cheap and it is very easy to mount it. It is more difficult to work with cotton and more expensive as you need to do Falshland (usually plasterboard) to protect basalt fibers, and besides, it is important to take care that moisture does not fall into the material structure. If this happens, the effect of all the work done will be zero, as all thermal insulation qualities will be lost very quickly.

It seems to seem to seem to seem that wool is better better (because "warmer"), but everyone solves the nuances of the situation. Yes, Wat seems to be good, but what is the meaning in it, if necessary, for example, insulate the room of the soul is not in the house, but, for example, in the country and I do not want to invest? An obvious budget solution in this case is a metallized insulator - stick it on the wall and forget.

But in the case of a more or less major approach, but again, in the absence of noticeable financial resources, it is better to stop the choice on the Minvat and insulation from the inside. It turns out that there is no ideal version and make a solution only on the basis of project features.

Thermal insulator manufacturers and their products

The most demand for the consumer uses a rolled insulation of several manufacturers.

KNAUF is a German trademark, the products of which does not contain in formaldehydes, which gives the finished product absolute safety and harmlessness, relevant when carrying out installation work.

Isolation from Knauf.

In such insulation, rodents and insects are not fartered, they have a wide range of a row, a long service period and the possibility of use for insulation not only apartments, but also country houses (cottages).

Isover is a French manufacturer, offering a wide selection of roll insulation with excellent performance, including a foil coating. Products are suitable for insulating events both indoors and outside their limits, it is not susceptible to burning and is able to fade in a fire.

Insulation for outdoor and internal works

URSA - Spanish insulation under this brand is characterized by a long period of operation with the full preservation of the main technical parameters. The manufacturer guarantees the highest quality of its products and its effectiveness both in private and industrial construction.

Tekhnonikol is a Russian manufacturer offering high-quality products at quite affordable and democratic prices. These rolled insulation are produced on the latest equipment with the involvement of innovative technologies and techniques, which makes it possible to guarantee not only quality, but also a long service life.

Classes and types of rolled waterproofing

Released roofing waterproofing depending on the purpose, the quality of the components used and the price category is divided into several classes.

Class material	Name	Price range	Characteristics	Purpose
Premium	Technoelast	100-160 rubles / m2 for models with a noise absorbing effect - the price of up to 250 rubles / sq. Meter.	The filtered coating with the application of bitumen and SBS modifier. Used at temperatures from -50 to + 1000c.	Bottom / upper layers of roofing, underground communications.
Technoelastmost	235-250 rubles / sq.meter.	A cloth with a thickness of 5-5.2 mm, the level of heat resistance - to + 1000c. Filler - bitumen with artificial rubber (SBS). High strength coating, service duration - up to 40 years.	Waterproofing plates of the progress on the roadway of the road or in the form of an adhesive layer on the spans of bridge structures.
Business	Uniflex	85-130 rubles per square meter depending on the thickness and type of base.	Film coating with a CSP-modified bitumen filler. Resistance to damage, durability. Expert period between repairs is at least 18 years. The flexibility of the material is preserved at temperatures up to -200c.	Laying the upper and lower layer of roofing, repair roofing work, waterproofing of the foundation, basements, basement floors.
Standard	Bipol	70-90 rubles / sq.meter	Claimed material, knitting layer with a thickness of 1.5 mm. Withstand temperatures from -150c to + 850c. The top layer of the coating is shale crumb. Service life - 5 years.	Used as the first layer of roofing or for the top of the roof. Repair of the roof of a residential foundation.
Bicroelast	67-84 rubles / square meter.	Claimed material based on glass cholester, fiberglass or polyester. Protective coating - sprinkle from shale crumb or film. Thickness 3-4 mm, retains flexibility at -100c.	It is used as a lining material for the construction of the roof, waterproofing of structures of various types - buildings, tunnels, bridges. A variety "K" is used to cover the upper layer of the roof.
Economy	Bikrost.	55-85 rubles / sq.meter.	Film coating, with bitumen filler. Flexibility is maintained only at the plus temperature, heat resistance - up to + 800c. Thickness 3-4 mm, service life - up to 10 years.	Waterproofing, the device of the lower / top layer of the roof - depending on the coating.
EuroRuberoid P.	13-16 rubles / sq.meter.	Fiberglass-based coating, with applying modified bitumen. Protective progress is applied on both sides of the insulating web. The thickness of the protective layer is 2-5 kg \u200b\u200b/ square meter.	Waterproofing of building structures, arrangement and repair of roofing carpet in facilities.

The building materials market represents a wide range of models of rolled waterproofing coatings - both universal and intended for a particular type of work.

Characteristics

For thermal insulation material in rolls released under various trademarks, common characteristics are characteristic.

Ecology

The insulation meets the regulatory requirements of environmental safety.

As a rule, there are salts of heavy metals, alkalis, acids, oxides, phenols, or toxic organic compounds, which are inactive at room temperature, are present in a minimal amount.

Due to the low chemical activity, thermal insulation practically does not interact with aggressive media, and therefore, for example, the effects of the solvent is not afraid.

Biological durability and fire safety

Material has a high level of biological resistance. As a result, there are no rodents, fungus, mold. For insects and animals, he is not interested in food. Depending on the composition and other characteristics, the insulation is able to withstand the effects of high temperatures.

Air and vapor permeability

If the insulation is used for heat insulation or walls, breathability is an important indicator.

When using rolled materials, you can not be afraid of excessive dampness in the room, condensate formation and other negative phenomena, provided that the installation is made correctly.

Departing for the purchase, it is worth remembering the following aspects of the choice:

For internal and outdoor use, various variations of the insulation are suitable.
It matters the surface that will be covered with rolled insulation. There is a fundamental difference between materials used for ceiling insulation and walls. For each of these grounds, it is provided for its insulation.
It is important to remember that the walls are made of what material. The heat insulator for the wooden base may be unsuitable on a concrete base and vice versa.
When choosing the thickness of the material it is worth taking into account the temperature conditions in the winter and climate features for a particular region.
Before purchasing, it is obligatory to familiarize yourself with the quality certificates and other permitting documentation for the selected rolled insulation, and in addition - to make sure the integrity of the packaging. Moisture, even in a minor quantity, is capable of negatively affect the calculated parameters of the material and its properties.

Choose high-quality material of proven manufacturers

Heatters in rolls are presented in the market in a wide range. Each of them has its own characteristics, has positive and negative characteristics. The choice of a specific option is the user's lot, but if there is difficulty, you should not rely in case. It is better to seek help to professionals and save your nerves and money.

3 Rolled Foil Heat Insulation

The rolled foil insulation presented on the market is usually manufactured either based on polyethylene foam (rather popular brand "Penofol"), or based on polypropylene ("Penoterm").

These are two practically identical to each other material, the difference between which is only in physical and mechanical characteristics. If we consider only affecting the direct efficiency of use as a thermal insulation material, then a foil rolled insulation for polypropylene-based walls looks more preferable.

Thus, the polypropylene base has an order of magnitude smaller in thermal conductivity (a difference of about 30%), less moisture absorption and better resistance to external mechanical impacts.

In fact, the last factor can be neglected, since the foil insulation themselves, due to their minimum thickness, do not perform effective warming when the foil is damaged, so it is important to look at the quality of the foil coating. .

Solid foil rolled foam

Unfair manufacturers, in order to reduce the cost of products, not aluminum foil can be used as an shielding layer, as the technology requires, and the usual metal spraying.

The effectiveness of such spraying is much lower than that of the foil, the cost of such products sold under the guise of high-quality insulation is comparable with high-quality goods from proven manufacturers. Choosing a heater covered with foil for walls, floor, or pipes, carefully check the quality of the shielding layer.

High-quality foil thermal insulation has the following advantages:

High heat shielding coefficient, about 97%;
Wide functionality - foil materials are used not only for domestic insulation of walls, gender and ceiling, they are also widely in demand for the thermal insulation of all sorts of industrial equipment;
Minimum rud weight;
Easy installation - foil thermal insulation does not require frames, anchor fastening and the like of the sores, it sits on the wall on the mounting foam, or the usual building glue;
Minimum cost - the price of foil materials is significantly lower than mineral wool;
Full vaporizolation;
Safety for the human body.

Foil thermal insulation has only one essential disadvantage - it is susceptible to burning. The temperature regime of the polypropylene is 150 degrees, polyethylene agent - 80 degrees.

3.1 Features of the thermal insulation of the balcony with a foil rolled insulation (video)

Characteristics

Rolled insulation materials are characterized by the following basic parameters:

Ecology. All models presented in the market must comply with the installation requirements for installation, operation and disposal. They must contain small amounts of harmful substances, these substances should not be released from the insulation during its storage, stacking and during use. The packaging indicates a method of recycling. Materials are resistant to the action of organic solvents and other active substances.
Fire and biosis. Mineral insulation does not burn himself and prevents the spread of the flame. Foam materials are able to withstand fire a certain time. Materials prevent the occurrence of mold and scare rodents.

Air and vapor permeability. Key features. They show how air volume or water vapor at a certain temperature can be leaked through a unit of material area. Parry permeability is necessary in order to remove excessive dampness from the room outward through the walls and systems of their ventilation.
Strength. An important characteristic of the insulation under the wallpaper. Touch, including solid objects, should not lead to damage to wallpaper.

What rolled insulation buy

This section of the site presents rolled insulation, the price of them and parpets of rolls. All information about products from different manufacturers is given on one page. Here you will find a brief description of each of them.

Roll insulation Ursa

This is a very well-known line of the insulation of the European manufacturer - the "Uralita" concern. Roll insulation of URSA brand are soft elastic mats from staple fiberglass. Each brand has its own marking that allows customers to easily navigate in the characteristics of the material and, accordingly, in its purpose. URSA insulation are high-quality light heaters recommended for use in horizontal unloaded building structures. Good heat engineering characteristics, the ease of transportation and installation make them the most demanded over the years.

Rolled insulation Knauff

You can always contact our specialists who will prompt you where you can find additional information about the insulation you are interested in or will be given tips on the installation of material.

Montaja technology

We turn to the installation of walls with a rolled type of insulation from the inside. Produce it through the preparation of walls to pasting. Special glue for wool is bred, the wall should not be in putty or plaster, only bare concrete or brick is allowed. The composition is applied to the wall evenly under a special comb, after which they begin to stick rolls, which can be trimmed for convenience.

At the same time, it is advisable to do the wall itself to the level, the plane, if there are no further plans for the firmware in the box or glasses of glasses. After the material is mounted on the wall, it is necessary to fasten it, each petal should be slightly recessed in the cotton. 1 m2 requires at least 5 locking holes. Better to secure the sheets and space between them (in this case, both sheets are grabbing, which will avoid blocking, output level and plane).

After the sheets grabbed, a layer of glue should be applied. The technology resembles a putty, only by another solution.

It is important to monitor the level and plane. It is necessary to make at least two passes, since the first time put a good layer will be problematic

After alignment, regardless of the type of room, you can move to the following works. When mounting the sheets of drywall inside the house they are fixed by means of a dowel on a layer of heat insulation, which is desirable to be treated with glue, as in the previous paragraph.

On the advantages of rolled URSA insulation, look in the video below.

Operational imperfections and maintenance complexity

For each type of waterproofing materials, their unique features are characterized. So, Tehtonikol, which, as the manufacturer asserts, withstands large mechanical loads, with high mobility of the soil may not withstand. Therefore, many apply a modification for waterproofing road substrates from the same manufacturer. But these are unjustified costs.

As for the service, then, for example, in the event of damage to the travelery coating, it is enough to sput a small layer to this place locally. But the rolled waterproofing, which peelled in any place, requires serious repair. It is necessary to remove it, at least in this place, to prepare the basis, again apply isolation, broken the formed seams. Of course, no aesthetics of speech does not go, and the quality of such a margin will be distant from perfection.

Waterproofing with rolled materials is not universal. So, with their help it is impossible to process the surface of complex forms, for example, the bottom of the car. And even rolled waterproofing of the roof can be a serious problem. In addition, high temperatures pernicably affect this material and the degree of its clutch with the base.

The main disadvantages of waterproofing with rolled materials under specific conditions:

Rolled roof waterproofing - the impossibility of treating surfaces of complex forms, a long process of applying, exposure to the negative effects of temperature differences, maintenance complexity
Rolled floorproofing floor - bad perception of constant mechanical loads, especially in vibration conditions
Rolled waterproofing foundation - instability to the negative effects of moving soils, additional load on the foundation, which is undesirable in zones with elevated levels of groundwater and in loose ground bases

Characteristics of basalt wool

If you do not fit the insulation under the wallpaper roller, we are talking above, then you can choose basalt, or fiberglass cotton wool that has a wide potential of application. It can be installed on the walls or gender, as well as on ceiling spans. It is not recommended to use this material for an inclined roof, this is due to the fact that over time there is a slide of the array, and the insulation density is violated. If you want to use this floor, then you need to lay at least two layers. This will get 1 thickness decimeter. If there is a need to insulate the walls, then you should use twice the smaller amount, there will be enough laying of the material into one layer. If you want to achieve the arrangement of an efficient heat-saving screen, then such thermal insulation with steam and waterproofing should be used.

What you need to take into account when working

Warming with mineral rolled materials can be carried out at any time of the year, it is important only to protect the material from precipitation. . The use of foamed materials mounted on the adhesive layer depends on the air temperature

Usually restriction up to -10c. Special adhesives are manufactured, effective up to -20c.

The use of foamed materials mounted on the adhesive layer depends on the air temperature. Usually restriction up to -10c. Special adhesives are manufactured, effective up to -20c.

Before the start of warming, it is required to carry out minimal surface preparation:

Dismantle pipes, wiring, lamps, decorations, plants, etc.
Clean the walls from the remains of old coatings, garbage and dust.
Install the crate for mineral insulation.
Align and clean the surface for sticker foam insulators.

Installation does not require special equipment, you will need from tools:

construction knife;
stapler;
screwdriver;
a hammer;
double sided tape.

Installation and cutting of rolled insulation are more conveniently carried out together, especially with large amounts of work. Small volumes under the power and one wizard.

Heat process

The sequence of operations during the installation of mineral insulation is the following

A steam insulating film is attached to the prepared wall.
Mounted a doomlet of wooden bars or metal profiles. The recommended step of the guides is 50 or 60 cm.
Rolls are manifested in accordance with the selected step. Cutting should be carried out so that the insulation is consistent between the tight guides and, painting, ensured the best fit to the guide.

Tarbed dowel

Mineral wool is attached to the wall with the help of plate plastic dowels, cut in accordance with the layer thickness at the rate of 4-5 per square meter.
The wind insulating film is attached to the guides on top of the cotton wool. The joints of the film are compacted by double-sided scotch. Installation of insulation on the walls of the house.
Installation scheme under the crate
Thermal insulation is made. You can move to the installation of the selected cladding - wooden or vinyl siding. To ensure the ventilation of the facade over wind insulation, install a secondary crate of thin regions.
Mounting scheme for plaster
Read on the topic.
Installation of a rolled foamed insulation for external and internal walls itself is easier, but requires better surface preparation. It will have to be aligned more thoroughly - the foam will not be able to english irregularities like mineral wool.
Fix foam rolls using a construction stapler is not recommended - braces create so-called thermal bridges for which the cold can penetrate the warm part of the room. The thermal insulation effect of the material is somewhat declined.
How to fix the insulation on the wall:
- Clear and align the surface of the wall.
- Remove the material at the calculation of the installation of the Job.
- In places of complex spatial form - next to the openings, in the corners, the adjoining of building structures (beams, balconies, etc.), it is better to try out the cutting pieces to spread glue or remove the protective layer.
- Apply glue to heat insulator or remove the protective film from the adhesive layer.
- Print the material by moving the top below.
- Smooth the surface with hands or rule, seeking the best adjunct. If scolded air bubbles were formed, they should be neatly pierced in the center of a sharp needle and, moving from the edges of the bubble to the hole, squeeze air.
After half an hour, the glue will grab and the heat insulating layer will be ready for operation. When mounting the cork sheet, the glue specially intended for cork. It is applied both on the wall and on the plug. Before sticking the wallpaper, a complete drying of the glue should be waited in order to avoid charging.

2 Roll insulation based on mineral wool

The quality of this category of insulation is regulated according to the requirements of GOST RF "52953-2008". This quality standard allows the following heat insulation material to the mineral wool insulation:

Basalt wool - the material produced by mirroring rocks and the subsequent formation of microscopic fibers that are combined into a solid carpet;
Slagovat is a material manufactured from the waste of the metallurgical industry. As a rule, it is much cheaper than basalt wool;
Glasswater - obsolete morally, but still quite often used, due to its small price material. Performed by melting glass.

Rolled Basalt Watch Inherent Characteristic Yellow Tint

The rolled insulation based on mineral wool, due to its elasticity and flexibility, is extremely universal material, which can be successfully used both for thermal insulation of walls, gender, attic, and other smooth surfaces and for thermal insulation of pipes.

2.1 Production of mineral wool

Consider the technology of manufacturing Minvati on the example of basalt insulation. Mountain basalt breeds whose chemical composition complies with the requirements of GOST, can be melted in two ways - hot and cold.

A hot method involves heating basalt breeds in blast furnaces, cold - exposure to electromagnetic radiation (according to the principle of conventional microwave).

The molten rock is served in a centrifuge, which is equipped with constantly cooled carbide discs. Under pressure, the melted basalt is fed into the centrifuge and falls on rotating discs, where in the process of carved cooling and pressure drop from the melt, separate basalt fibers are formed.

The resulting fibers are immediately removed from the drum with a special functional element and in the conveyor go to the laying machine, which forms the basalt wool carpet of the required thickness.

After laying the fiber carriage, the fiber is impregnated with a variety of impurities that are necessary for making the final product of the desired characteristics - hydrophobicity, refractory, density and elasticity.

Slag, as a rule, is of a dark shade

2.2 Benefits and Disadvantages

Among all the thermal insulation materials presented in the market in the middle price category, it is the mineral wool that has the lowest thermal conductivity. Although the leaders are generally foam and minvat.

An important factor is that the thermal insulation properties of mineral wool do not depend on any external conditions - this material is not expanding under the influence of moisture, is not subjected to thermal expansion, microorganisms and rodents are not created in the Ministry of Service.

Rolled heat insulation made of mineral wool is made with an extensive variety of performance - you can choose both minvatu small density for insulation of pipes and other uneven products and dense material for thermal insulation of surfaces experiencing external loads - floor, or attic overlap.

An important advantage of mineral wool is its fireproof. This material can withstand temperatures up to 700 degrees, it does not light up even under direct influence of fire. It is also worth noting and good noise-canceling properties - after performing the insulation of the walls and the floor with a roll minister, you decide not only the question of insulation, but also sound insulation of the house.

The only disadvantage of mineral wool is high steam conductivity, as a result of which, when installing this insulation, a special vaporizing film is required.

Thermal insulation of the pipeline with rolled glass

Mineral wool rolled warheads can be applied for the following purposes:

Insulation roofing, floor, walls, and any smooth surfaces;
Thermal insulation of pipes and pipeline mains;
Thermal insulation of industrial equipment;
Insulated element inside sandwich panels (here is the best heat insulation of Hitrock);
Internal insulation in false walls and when laying hollow walls;
Outdoor insulation of the walls of the house with subsequent plastering.

Roven offers to buy rockwool tube and rolled heat insulation in Sevastopol at a bargain price. We invite you to visit our office at: Sevastopol, Fiolentic Highway, 1/2, Liter L, office 105 (territory of the Lighthouse plant). Call by phone +7 978 117 57 03 Our experts will answer all your questions.

Cylinders Simple and combined mineral wool on synthetic binding Rockwool cylinders - Pipe isolation, which is hollow products from the stone wool of basalt group (simple). Rockwool cylinders can also be manufactured with aluminum coating (combined).

Pipe and rolled heat insulation Rockwool
Roll insulation: species and features of rolled insulation
1. Heat insulation based on roll insulation
2. The advantages of thermal insulation in rolls
3. Types and characteristics of thermal insulation in rolls
4. Heat insulator with foil surface: features
5. Tips for choosing heat insulation in rolls: what you need to know
Overview of the characteristics of heaters in rolls
How to choose the right rolled insulation for roofing
1. Scope of insulation in rolls
2. Types of insulation
3. Manufacturers Review: Eau return, Knauf, Urs
Rolled insulation
1. Scope of the rolled insulation
2. Thermal insulation rolled materials from Minvati
3. Rolled insulation foofol

Low thermal conductivity coefficient and high thermal insulation properties
High biostostity and chemical resistance (to solvents, oils, acids and alkalis)
Advanced operating temperature range (melting at temperatures over 1000 ° C)
High temperature does not affect the thermal insulation properties of the material
There is a longitudinal incision for the convenience of mounting, it is easy to cut by cutting tools.

Technical characteristics of rockwool tube isolation

λ125 \u003d 0.048 W / (M · K)

λ300 \u003d 0.087 W / (M · K)

Flashing group Rockvul

Ng, coated with foil - g1

Temperature of the use of Rockvul

from -180 to +650 ° С

Acidity module, no less rocular

Rolled heat insulation

Wired Mat 80 is made from stone wool based on basalt rocks. One side of the mat is covered with a grid with 25 mm cells made of galvanized or stainless wire. In addition, the mat is stitched galvanized or stainless wire (SST). The product can also be produced with one-sided aluminum foil coating (ALU WIRED MAT 80).

Those mats - light hydrophobized mats on synthetic binding, made of stone wool based on basalt breeds. On the one hand, mats can be combined with aluminum foil.

Application:

Wired Mat 80 is used for thermal insulation of technological and energy equipment, thermal networks, trunk and industrial pipelines with a temperature of up to 750 ° C.

ALU WIRED MAT 80 is used for air duct flaxes.

Those mats are used for thermal insulation of pipelines and industrial equipment. Maximum use of + 570 ° C.

Pipe and rolled heat insulation Rockwool Roven offers favorable prices for rod and rolled thermal insulation Rockwool in Sevastopol. Description, specifications, photos.

Conditional designations of rolled waterproofing

In addition to the name of the model of waterproofing material, alphabetic marks are present in the title. Each of the letters denotes a specific feature inherent in this brand of waterproof, based on the use of a particular basis and characteristics of the protective layer.

Thus, the rolled insulation of the model of the uniflexible CPP is decrypted as the material with the base of the glass cholester, on both sides coated with a protective film.

Rolled waterproofing technonikol

Rolled waterproofing, manufactured under the brand of Technoniscol, has a leading position in the ranking of building materials in the international market. The basis for the popularity of MAROK TECNONICKS are:

high degree of reliability and efficient protection against moisture and condensate formation;
biological and chemical resistance, preservation of flexibility and elasticity at low temperatures;
the ability to withstand a significant load on the gap;
long-term service life - from 35 years;
easy styling, efficiency.

The strength of the hydroizolate technologies is due to the use of a multilayer structure consisting of their polyester base, two layers of bitumen-polymer filler and a protective film. All coatings are made in strict accordance with GOST and existing building standards.

Under the brand Tekhtonikol, new models of rolled waterproofing are being developed, taking into account the various climatic conditions and the production capabilities of the consumer. Homeless self-adhesive rolled coatings for waterproofing floor and foundation are widely used.

In addition to the protection against moisture, waterproofing coatings from TechnoNIKOL are capable of carrying out the functions of premises from noise, dust, malicious gas.

Roofing and insulating materials are used both in the construction of new buildings and in repair and restoration work. The scope of use of waterpores from TechnoNIKOL includes:

strengthening foundations under industrial structures;
construction of houses of high floors;
hydraulic protection of private households from the destructive effects of dampness and moisture;
construction of tunnels, viaducts and bridges using reinforced concrete slabs.

Modern rolled materials for waterproofing are able to effectively and reliably protect the structure or structure from groundwater, freezing and precipitation. The right choice of waterproof, strict adherence to the recommendations of specialists and installation technology - the basics of successful laying of rolled waterproofing and durability of the structure.

Overview of manufacturers Eau return, KNAUF, URSA

The quality of the insulator is undoubtedly to a certain extent depends on the manufacturer.

kNAUF-1.
kNAUF-2.

Knauf is a German producer product created from natural minvati on the latest Ecose technology. This is an environmentally friendly insulator, since it does not include formaldehyde. Even with direct contact with this material, it remains safe for a person, it does not cause allergies. It can even be used for interior. This is a reliable protection from cold and noise.

Distinctive characteristics of materials KNAUF:

high degree of steamproof;
low water absorption;
chemical and biological inertness.

isover-1.
isover-2

French isolation escape. This is a relatively cheap option of insulation roofing. This is the most dense material among the analogues. Available in rolls of different thicknesses: 2, 3, 5, 10 and 15 cm. What advantages have a warmother of a rolled out of the classic. Reviews show that he

excellent soundproofer;
environmental;
it does not burn, when exposed to open flame does not have toxic discharge;
durable;
simple in installation.

uRSA-1.

Ursa is another of the popular brands. It is distinguished by his durability, it does not break and not crumble, it is easy and easy to work with it. Produced in options for a radio width: 5; 8 and 10 cm.

Types and characteristics

Mineral wool materials for isolation are widespread.

It is explained by their popularity of high operational and technical indicators and relatively low cost.

Mineral wool's rolled insulation facilities include:

. The material was obtained as a result of mirroring of rocks of a certain type and formation of thin fibers.
Glasswater. The insulation produced from molten broken glass has an affordable cost. Due to this, the material is in high demand, although it is considered morally obsolete.
Slag. The material is based on the material of the metallurgical industry, so it is quite low price.

Mineral wool-based insulation have their own distinctive properties:

resistance to temperatures;
low thermal conductivity;
high density;
absorption of vibrations and sound oscillations;
no shrinkage after long-term operation.

Foil rolled insulation is made from foamed polystyrene foam, by applying it on a foil layer. The foil creates the effect of the thermos, repulcing heat back to the room.

Specialist Council: Folgized insulation can be used when installing infrared floor, with heat insulation of wooden saunas and baths.

The main properties of the foil rolled insulation can be called:

high heat insulation;
reliable vapor barrier;
good noise absorption;
fire safety;
durability.

Interventical rolled insulation constitute a rather specific solution. The main purpose is to fill the empty space between the crowns. Even a high-quality assembly of houses from a profiled timber or log cannot guarantee dense adjacent elements. Interwidden thermal insulator will fill out free space.

The material is produced by narrow rolls, natural and harmless materials are used for its manufacture, such as flax, batting, jute. The use of this type of insulation is possible both during construction and during the operation of the house. Everyone knows that over time, the tree dries, forming a slot between the elements of the structure. Filling the obtained empties insulation with the help of the chisels and the image, it is possible to maintain the heat in the house.

Mineral wool insulators

The materials of this group have the greatest prevalence in the domestic market. This is due not only by their excellent operational and technical data, but also acceptable pricing policies - a similar combination is still unattainable for competitive proposals.

Flexibility simplifies work

Assortment and features of species

The term "mineral wool" is a unified designation of a number of heat insulators, namely:

basalt wool - for the manufacture of this material, the combustion technology of certain rocks is used, followed by the formation of the finest fibers, glued into a single carpet;
glasswater - material, although relating to morally obsolete, but still has a rather high demand, due to the available cost. For its production, we use melted glass battle;
shelotte - its base is the waste obtained in the metallurgical industry. Thanks to this, such a heater in rolls has a lower rather than basalt and glass gambled, cost.

Each of the varieties of mineral wool has its own distinctive features and features. Thus, the glass gamble is perfectly resistive to high temperatures, up to 450 degrees - after exceeding this parameter, the material is destroyed in irreversible order. The greatest density is 130 kg / m3, thermal conductivity indicators vary in the range of 0.038-0.046 W / m * p.

Glasswater in rolls

Glasswater is not a combustible, it does not even tweet, perfectly absorbs vibrating manifestations, confront sound oscillations and does not give shrinkage even with long-term operation. At the same time, the material is not moisthable, and its wetting completely levels the entire spectrum of positive characteristics. It is worth noting and the fragility of glass gambles, as well as the fact that contact with human skin causes the strongest itch.

As for the basalt cotton wool, such rolled insulation is able to withstand temperatures up to 700 degrees. Its thermal conductivity is 0.035-0.045 W / m * C, the density reaches 220 kg / m3. Material is resistant to moisture action, minor wetting does not affect its parameters. Basalt wool is an eco-friendly and non-irritation material.

Basalt Wat.

Shelotte has the greatest mass, and its density reaches 400 kg / m3. The material is characterized by a minimum thermal conductivity - 0.046-0.048 W / m * C, and the highest temperature that it is able to withstand is 300 degrees - its increase causes melting slag and the destruction of its structure.

Slotted in rolls

The dimensions of the materials are largely dependent on the manufacturer, but most often they have such sizes:

length - varies within 3-6 m and more;
the width is the standard indicator of 0.6 and 1.2 m, although the products of individual trademarks can be width of 1.22 m and 0.61 m;
thickness - 50, 100 and 150 mm.

Installation on the wall

Despite the fact that the rolled insulation is created from different materials, they mounted it on the wall according to the standard principle. All differences will be contained in the composition of the adhesive, which will be used, and, accordingly, in the time of drying the substrate on the wall.

Conditions for installation work with a substrate indoors

For gluing the insulation flat walls, you have to do the following:

First of all, it is necessary to prepare the surface, for which you need to remove the old wallpaper, plastering the wall, smoothing and embedding large gaps and irregularities. Small wall surface defects can be left, they will close.
Next, the surface of the wall must be projected. It is done either with the help of glue, which we glue the substrate divorced in a weaker consistency, or with the help of a special primer composition. After the primer, it is necessary to wait until it absorbs into the wall and dry.
Rolled insulation is recommended to cut into pieces of the required length in advance so that it can lie down and align. This will greatly facilitate our sticking. When cutting the canvas, add a little insure material.
The glue composition prepare according to the instructions on its pack. If we are dealing with a substrate with a top layer of paper, we applied glue on the wall and on the sliced \u200b\u200bpieces, and let them be soaked in composition literally 5 minutes. If the substrate is equipped with fliesline edges, it is enough to smear the wall, and the material easily attaches to it.

Next, go directly to the installation of cloths on the walls. This process resembles the sticking of the wallpaper, the pieces are also glued into the joint and carefully smoothed. From under the canvase, the air is driven out and it is firmly glued to the wall. It is convenient to use a rubber roller, it will create the desired pressure and does not hurt the insulation cloth.
After the insulation is dry, after about 1-3 days, we stick the joints with the usual painting scotch. Solving will allow the monolith of our design.
Now our walls are well insulated, and you can proceed directly to the blending of the wallpaper themselves.

The insulation for the walls will allow us to create the most comfortable conditions for living. He will serve us a long amount of time as you do not have any wallpaper.