How to make benches, tables, benches and other garden furniture from a profile pipe. DIY metal bench: Photo Garden benches from a profile pipe

A profile pipe is a pipe made of carbon or low-alloy steel with a cross-section other than round: rectangular, oval, diamond-shaped or square. Such pipes are widely used in industrial and private construction (frames of small buildings and kiosks, carports, garden gazebos and swings, fences, gates or a bench made of a profile pipe). This article provides a description of how a simple pipe bench is made without a back and with a back.

Making a bench with your own hands is not at all difficult. The difference between shaped pipes and pipes with a circular cross-section is in their increased resistance to physical stress. Furniture made of steel pipes is usually not exposed to overload, and therefore thin-walled pipes with a thickness of 1-4 mm are taken for its manufacture. Such pipes are easy to work with, they are inexpensive, and the resulting design is lightweight. As for the thickness of the pipe, it directly depends on the functionality of the future structure and the expected load on it. So, in the manufacture of a garden swing for adults, the thickness of the pipe will be at least 2 mm, and in the manufacture of a bench, 1-2 mm of thickness is sufficient. For the manufacture of furniture, pipes with a section of 40x25 mm or 20x20 mm are taken.

It is quite difficult to make a pretentious and complex bench without appropriate experience, but a bench with a laconic design is within the power of even those who have never had experience with a welding machine and bending device.

What is required to make a bench.
Steel profile pipes

Regardless of what kind of bench model will be made, the following materials and tools will be required:

profile pipe of the required diameter,
boards for making a seat,
welding machine and electrodes (3 mm in diameter),
grinder or hacksaw for metal,
file, drill with polishing attachment or grinder,
building level,
meter and square,
planer (if the boards are not planed),
anti-corrosion paint,
paint on wood or stain,
pan head bolts and nuts,
hammer, drill and pliers.

Bench bolt

Profile tube benches can be decorated with bent elements. This will require a device designed for bending pipes. In this capacity, a mini-machine "Snail" is usually used, a locksmith's vice or a bending tool made from old brake discs for a car.

In order for the bending of paired parts to be the same, a plaza made from a piece of plywood with the contour of the future part applied to it is used. A blowtorch may also be required to obtain clean and graceful bends - it heats up the folds with it.

The pipes are tightly filled with sand before the coiled tubing, so you should take care of it in advance. The bending procedure is simple: the pipes filled with sand are placed on the machine between the stop and the center lip and then bend to the desired angle by hand. Below is a drawing of a pipe bending on a machine made from a car rim.

The principle of bending steel parts on a machine

For the manufacture of bent parts, preference should be given to round or oval pipes - they are easier to bend.

How to make a bench without a back
A bench without a back is a structure of supports in the form of three metal rectangles connected by two pipes that form a seat. Below is a drawing of a bench made of a shaped pipe.

Shop details
To make such a bench, you will need a square or rectangular shaped pipe with a section of 30x30 mm. In total, 11 meters of pipe are needed, from which blanks are cut using a grinder or a hacksaw for metal:
2 sections of 2.3 meters (long parts of the seat holding the supports);
6 segments of 0.6 meters each (long parts of the support-rectangles);
6 segments of 0.45 meters each (parts of the support-rectangles are short).
Prepare 8 wooden blocks of rectangular shape with a width of 6 cm from wooden boards. To connect wooden blocks with a metal frame, you will need bolts and nuts (24 pieces).

Fastening bolts should be selected with a rounded flattened head that does not leave defects on clothing. Alternatively, the bolts can be sunk into the wood, but this makes the wood more vulnerable to moisture in the fasteners.

Sequencing
Such a do-it-yourself pipe bench is quite simple to assemble: first you need to weld 3 metal rectangles, and then connect them with two guides that form the seat frame. It should be remembered that:

Long sections of rectangular supports will be placed horizontally, and short ones - vertically.
During welding of segments, the angles of the supports should be controlled: they should be 90 degrees.
The length of the bench, as well as the width, can be changed. If the length of the bench is increased, the number of supports will need to be increased.
After welding the supports, all the seams on them are cleaned with a grinder or file, and then primed.
After connecting the metal supports, 8 holes are symmetrically drilled on each of them for attaching wooden planks.
The frame of the bench is covered with anti-corrosion paint.
Wooden boards for seating are varnished or stained in advance.
The boards are attached to the frame last.

Bench on two supports

The wooden seat slats can be replaced with rectangular shaped tubes. In this case, they are simply welded to the frame, and then the entire structure is covered with paint.

For aesthetics, iron slats can be placed in a metal frame to hide the sharp end pieces. This will require an additional 1.2 meters of pipe. Such a bench can be placed autonomously - in a park or in a garden, but in rainy weather it is recommended to cover it with foil or place it under a canopy.

Duralumin pipes cannot be welded. Such pipes are connected by bolting.

How to make a bench with a back
A bench made of a profile pipe with a back will require more time and materials, but it is these models of this garden and park furniture that are more comfortable and loved by vacationers. Below is a drawing of a bench made of a shaped tube with a back.

Drawing of a bench with a back

Shop details
To make such a bench, you will need 8 meters of a profile pipe with a section of 25x25 mm, as well as boards for a seat (30 mm thick) and a back (25 mm thick). Frame parts should be prepared from metal pipes:

1 piece 1550 mm (crossbeam between supports);
2 bent with a span of 100 mm, sections 780 mm high (for the back and rear of the supports);
2 pieces of 350 mm (for the seat base);
2 pieces of 390 mm each (for the front of the supports);
2 pieces of 200 mm each (to strengthen the front supports);
4 metal plates 40x40 mm (for a stand on supports);
2 bent metal strips 450 mm (for connecting supports on each side).
To create a seat, you also need to prepare boards of the required length:
3 boards 1600 mm long, 60 mm wide and 30 mm thick (for the bottom of the seat);
3 boards 1600 mm long, 60 mm wide and 25 mm thick (for the back).
To connect the frame to wooden planks, you will also need round head bolts and nuts in the amount of 24 pieces.

Sequencing
After all the details of the future shop are prepared, all that remains is to connect them. Start with the seat frame:

First of all, the transverse crossbar and two segments of 350 mm are connected to each other. The crossbar should be located exactly in the middle of each line and perpendicular to them.
Next, 2 bent 780 mm segments are welded to the resulting structure. The place of welding is at the bend of the pipe.
At the next stage, the front parts of the supports are welded to the frame. In this case, the junction of the front supports with the seat base is 9 cm from their front.
The front legs are connected to the crossbar with pipes - for the strength of the bench.
The frame is almost complete. It remains to weld two arcs between the supports and the pads on the ends of the legs (supports).
The resulting structure should be sanded (welding places), primed and painted with anti-corrosion paint. At this stage, a garden bench made of a profile pipe should look as shown in the figure below.

Skeleton of a bench made of a shaped pipe

After that, it remains only to symmetrically arrange the boards for the seat on this frame. Treat the boards with a plane, cover them with varnish or stain in advance. Thicker boards go to the bottom of the seat, while thinner boards go to the back. Fastening is done with two bolts on each side of the board. Below is shown how the do-it-yourself shop from the pipe will look in finished form.

Garden bench with backrest

If desired, the boards can be coated with colored paint, as well as replaced with metal rectangular pipes.

Profile pipes are an excellent building material for the manufacture of various structures and pieces of furniture. The advantages of products made from them are resistance to physical stress, inexpensive cost, low weight. That is why benches made of shaped tubes are an excellent solution for arranging a garden. And curved elements on the bench frame will create an aesthetic look. The ease of working with the material allows you to make a bench with your own hands. All that is required for this is step-by-step instructions, a drawing and an available set of tools.

Required tools

A beautiful, lightweight, durable bench is a real decoration for a garden plot in the country. Buying a bench in a store is not a cheap pleasure, so it will be much cheaper to make an item with your own hands.

To make a bench you will need:

profiled pipe of the required diameter to create a frame and bends;
boards for making seats, backs;
welding machine and electrodes;
grinder for cutting pipes into the desired elements;
drill;
sanded paper or file for sanding;
level;
roulette;
a planer for sanding boards;
paint for painting metal, wood;
bolts and nuts for screwing wooden elements to the frame;
hammer;
pliers.

The easiest way to do it yourself is a bench without a back. This design consists of 3 metal rectangles, which are interconnected by 2 pipes.

This will require:

pipe 30x30mm 11 meters long;
2 pipes 2.3 meters each:
6 pipes 0.6 meters each;
6 pipes of 0.45 meters;
8 rectangular wooden blocks, 6 cm wide;
bolts and nuts - 24 pcs.

It is not difficult to make a bench with your own hands, but you should be guided by the following rules:

Short pipes are placed in a vertical position, and long ones in a horizontal position.
The support angle must be 90 °.
At the end of the welding work, all seams should be filed and then primed.
After the metal supports are connected, 8 holes must be drilled on each of them for fastening the boards.
For the holes to be symmetrical, you need to use a tape measure.
Cover the finished frame of the bench with metal paint.
Paint or stain the boards.

It is necessary to weld 3 rectangles together, and then combine them with two guides, which form the frame of the structure. It is recommended to fasten the boards to the frame last, when they are sanded with a plane, opened with varnish or paint.

Special attention should be paid to the bolts. It is recommended to give preference to fasteners with a rounded head, because otherwise it will protrude above the structure, thereby causing inconvenience.

How to decorate a bench with a pattern?

Benches are often decorated with patterns made of steel elements. You can also make them yourself. At first glance, the execution of a bend may seem complicated, but in the presence of a profiled pipe, a locksmith's vice, a snail machine and the ability to read drawings, such a task is within the power of everyone.

There are 2 methods for bending shaped pipes - hot and cold. It is strongly not recommended to bend the product in its normal state, as it can damage the structure. Therefore, they use the following methods:

The "cold" method is applicable in winter and is relevant for bending copper pipes. To do this, one end of the profile pipe is sealed with a stopper, and water is poured into the second hole. Then the product should be taken out into frost and kept until the water freezes. After such manipulations, bending is performed using a blank.
The "hot" method is considered more difficult than the "cold" method, but it can help to achieve more beautiful smooth curves. The bottom line is that the pipe is filled with fine river sand and both holes are closed with a wooden block. It is important that the length of the plug is 2 times the diameter of the pipe itself. At the ends of the product, you need to make several small holes for the free release of gas generated during the bending of the material. Areas to be bent should be marked in advance with chalk or a marker. To achieve smooth bends, a blowtorch is used, which should be used to heat the bending points. An important issue remains the symmetry of the patterns; for this, the contour of the future element can be applied on a piece of plywood.

The figure shows the hot tube bending method.

Bench with back

A garden bench with a back requires more time to make with your own hands, but it is convenient because you can always lean on it. Using a detailed drawing, you can create a comfortable, beautiful bench without much effort and material costs.

This will require the following materials:

8 meters of pipes with a section of 25x25mm;
boards with a thickness of 30-35 mm for the seat and 25 mm for the back.

From the profile pipes, you need to prepare the frame parts. This will require a grinder for metal and a tape measure.

1 piece of pipe 1550 mm long for the crossbeam between the supports;
2 bent with a span of 100 mm, sections 780 mm high for the back and rear of the supports;
2 pieces of 350 mm each will be the base of the seat;
2 pieces of 390 mm to create the front of the supports;
2 pieces of 200 mm to strengthen them;
4 metal plates 40x40 mm will serve as a stand on the supports;
2 bent metal strips 450 mm for connecting supports on each side.

3 boards 1600 mm long, 60 mm wide, 30 mm thick - for the seat;
3 boards of the same length and width 25 mm thick - for the back;
24 bolts and nuts for screwing the boards to the frame.

After preparing the frame, it remains to assemble the bench. To do this, it is necessary to connect the crossbeam and 2 pieces 350 mm long. It is important to take into account that the crossbar must be installed in the center of each segment, perpendicular to them. Then weld 2 bent segments 780 mm long to the structure. Weld at the bend of the pipes. After that, the front parts of the supports are welded to the frame. It should be noted that the junction of the supports should be located 9 cm from the base of the seat. In order to increase the strength of the bench, the front supports must be connected to the crossbar.

At the last stage, 2 arcs are welded between the supports and fixed at the ends of the legs. The finished product is polished at the welding points and painted. After the paint has dried, the wooden elements are installed to serve as the seat and backrest. The boards are preliminarily treated with a plane, polished, varnished or painted.

Making a bench with your own hands is a feasible task that does not require large expenses. All it takes is tools, materials, blueprints and a little patience. The product, in which strength and soul are invested, will be a real decoration of a suburban area or courtyard of a private house.

A do-it-yourself bench made of a profile pipe can become a real decoration of your suburban area. This is an inexpensive and practical way to create a summer cottage environment, which, in fact, any man can handle.

It makes no sense to make a bench completely metal - this way it loses a significant part of its functionality. In cold weather, sitting on a metal seat is not only unpleasant, but also dangerous to health.

The profile pipe is used only for the construction of the bench support - frame and legs. The seat, if desired, you can make of wood or plastic.

The metal base will make the bench strong, stable and durable, which is exactly what we need.

There are several options for making a bench, depending on the material. You can use plastic products of this type, but here you have to buy finished products, since plastic is not entirely suitable for folk art.

With regard to wood, this is the ideal solution, which is associated with the convenience of processing this material, which, moreover, is able to provide a special attractiveness to the final product. Also, a wooden bench is easy to install.

A more monumental option is to appeal to a material such as stone. The stone bench is an impressive appearance and utmost reliability of the structure. At the same time, it has some disadvantages. For example, sitting on such a bench without the same pillows is fraught with health problems.

Finally, a good solution is to use metal, through which a kind of artwork is created. This is accomplished through forging.

Do-it-yourself simple bench from a profile pipe

You will need:

Profile 8 meters long with a section of 25 by 25 mm.
Wooden board - for seat 30 mm thick, for backrest - 25 mm. The length is calculated according to the metal frame.
Fasteners - bolts with nuts - 24 pcs.

Frame

Pipe 1.55 m long on the crossbar between the supports.

Bent sections 10 cm, length (d) 78 cm on the back.
A pair of 35 cm long straight sections on the seat. Another 2 pieces 39 cm long to form the front supports and a couple of pieces to reinforce the latter 20 cm long.
Four metal plates 40 x 40 mm for the production of a stand that is mounted on the poles.
A pair of curved strips 45 cm long for attaching supports to each other.

Seat and back

Board - 3 pcs. 160 cm long, 6 cm wide and 3 cm thick for the bottom of the seat and three with the same parameters for the back. Bolts and nuts - 24 pcs.

How to make a bench without a back

A bench without a back is a structure of supports in the form of three metal rectangles connected by two pipes that form a seat. Below is a drawing of a bench made of a shaped pipe.

Shop details

To make such a bench, you will need a square or rectangular shaped pipe with a section of 30x30 mm. In total, 11 meters of pipe are needed, from which blanks are cut using a grinder or a hacksaw for metal:

2 sections of 2.3 meters (long parts of the seat holding the supports);
6 segments of 0.6 meters each (long parts of the support-rectangles);
6 segments of 0.45 meters each (parts of the support-rectangles are short).

Prepare 8 wooden blocks of rectangular shape with a width of 6 cm from wooden boards. To connect wooden blocks with a metal frame, you will need bolts and nuts (24 pieces).

Sequencing

Such a do-it-yourself pipe bench is quite simple to assemble: first you need to weld 3 metal rectangles, and then connect them with two guides that form the seat frame. It should be remembered that:

Long sections of rectangular supports will be placed horizontally, and short ones - vertically.
During welding of segments, the angles of the supports should be controlled: they should be 90 degrees.
The length of the bench, as well as the width, can be changed. If the length of the bench is increased, the number of supports will need to be increased.
After welding the supports, all the seams on them are cleaned with a grinder or file, and then primed.
After connecting the metal supports, 8 holes are symmetrically drilled on each of them for attaching wooden planks.
The frame of the bench is covered with anti-corrosion paint.
Wooden boards for seating are varnished or stained in advance.
The boards are attached to the frame last.

The wooden seat slats can be replaced with rectangular shaped tubes. In this case, they are simply welded to the frame, and then the entire structure is covered with paint.

What are the requirements for the shop?

Ease of use - the bench should provide an opportunity for a comfortable stay. It is good if it is equipped with a back, as this will only increase its comfort.
Ability to withstand appropriate loads - the quality of the build and the materials used must be high so that it does not collapse under the weight of people.
Resistance to weather conditions on the part of the material of manufacture.

The process of making a wooden bench

The design of the bench in question corresponds to the following dimensions: the length of the back and seat is 1500 mm, the width of the seat is 500 mm, the angle of inclination of the back is about 20 degrees.

What materials and tools will you need?

Boards, bars.
Antiseptic and varnish.
Sandpaper.
Self-tapping screws.
Plane.
Hacksaw.

Assembly instructions

With the help of a hacksaw, workpieces from the boards are cut to the required length. For this, you can use strips in the amount of 6 pieces, 1500 mm long and 140 mm wide.
Using a planer and emery paper, the workpieces are given the required surface smoothness, including the side edges. Then they are impregnated with an antiseptic and left to dry.
Two backrest holders are prepared with a 720 mm long x 140 mm wide leg. From the middle of these holders, a cut is made at an angle of 20 degrees, which is then sanded.
The supporting pairs of the bench are connected using bars and self-tapping screws. It is advisable to deepen the self-tapping screws into the wood using pre-drilling, which will reduce the effect of corrosion processes.
The bench seat is assembled, which will require 3 slats 1500 mm long, and the back of two of the same slats.
To give additional rigidity, the legs are connected from below with a board.
The bench is varnished or oil paint is used instead.

Simple construction. Option 2

If you need to assemble the simplest bench, then for this it will be enough to take two wooden blocks and nail a board about 40 cm wide to them.For greater reliability, especially if the structure is too long, another wooden block is installed in the center.

A more thorough approach to making a bench in a simplified form, which assumes the absence of a backrest, requires the purchase of the appropriate material. To do this, you need a beam and boards with a thickness of about 30 mm. You can also use clapboard to make a seat.

The legs are made of timber, which implies:

sawing off 4 blanks, which should also be fastened with a bar in the middle, making an insert, and in the same way from above;
if a board with a width of about 40 cm is used for the seat, then it will be enough;
prepared legs are attached to it with self-tapping screws, supplemented by 2 stops again from a bar, where one side is attached to the crossbar of the legs, and the other from the bottom side of the board used as a seat.

The difference between shaped pipes and pipes with a circular cross-section is in their increased resistance to physical stress. Furniture made of steel pipes is usually not exposed to overload, and therefore thin-walled pipes with a thickness of 1-4 mm are taken for its manufacture. Such pipes are easy to work with, they are inexpensive, and the resulting design is lightweight. As for the thickness of the pipe, it directly depends on the functionality of the future structure and the expected load on it. So, when manufacturing for adults, the thickness of the pipe will be at least 2 mm, and when manufacturing a bench, 1-2 mm of thickness is enough. For the manufacture of furniture, pipes with a section of 40x25 mm or 20x20 mm are taken.

What is required to make a bench

Regardless of what kind of bench model will be made, the following materials and tools will be required:

profile pipe of the required diameter,
boards for making a seat,
welding machine and electrodes (3 mm in diameter),
grinder or hacksaw for metal,
file, drill with polishing attachment or grinder,
building level,
meter and square,
planer (if the boards are not planed),
anti-corrosion paint,
paint on wood or stain,
pan head bolts and nuts,
hammer, drill and pliers.

For the manufacture of bent parts, preference should be given to round or oval pipes - they are easier to bend.

How to make a bench without a back

A bench without a back is a structure of supports in the form of three metal rectangles connected by two pipes that form a seat. Below is a drawing of a bench made of a shaped pipe.

Shop details

2 sections of 2.3 meters (long parts of the seat holding the supports);
6 segments of 0.6 meters each (long parts of the support-rectangles);
6 segments of 0.45 meters each (parts of the support-rectangles are short).

Prepare 8 wooden blocks of rectangular shape with a width of 6 cm from wooden boards. To connect wooden blocks with a metal frame, you will need bolts and nuts (24 pieces).

Sequencing

Such a do-it-yourself pipe bench is quite simple to assemble: first you need to weld 3 metal rectangles, and then connect them with two guides that form the seat frame. It should be remembered that:

Long sections of rectangular supports will be placed horizontally, and short ones - vertically.
During welding of segments, the angles of the supports should be controlled: they should be 90 degrees.
The length of the bench, as well as the width, can be changed. If the length of the bench is increased, the number of supports will need to be increased.
After welding the supports, all the seams on them are cleaned with a grinder or file, and then primed.
After connecting the metal supports, 8 holes are symmetrically drilled on each of them for attaching wooden planks.
The frame of the bench is covered with anti-corrosion paint.
Wooden boards for seating are varnished or stained in advance.
The boards are attached to the frame last.

The wooden seat slats can be replaced with rectangular shaped tubes. In this case, they are simply welded to the frame, and then the entire structure is covered with paint.

Duralumin pipes cannot be welded. Such pipes are connected by bolting.

How to make a bench with a back

A bench made of a profile pipe with a back will require more time and materials, but it is these models of this garden and park furniture that are more comfortable and loved by vacationers. Below is a drawing of a bench made of a shaped tube with a back.

Shop details

To make such a bench, you will need 8 meters of a profile pipe with a section of 25x25 mm, as well as boards for a seat (30 mm thick) and a back (25 mm thick). Frame parts should be prepared from metal pipes:

1 piece 1550 mm (crossbeam between supports);
2 bent with a span of 100 mm, sections 780 mm high (for the back and rear of the supports);
2 pieces of 350 mm (for the seat base);
2 pieces of 390 mm each (for the front of the supports);
2 pieces of 200 mm each (to strengthen the front supports);
4 metal plates 40x40 mm (for a stand on supports);
2 bent metal strips 450 mm (for connecting supports on each side).

To create a seat, you also need to prepare boards of the required length:

3 boards 1600 mm long, 60 mm wide and 30 mm thick (for the bottom of the seat);
3 boards 1600 mm long, 60 mm wide and 25 mm thick (for the back).

To connect the frame to wooden planks, you will also need round head bolts and nuts in the amount of 24 pieces.

Sequencing

After all the details of the future shop are prepared, all that remains is to connect them. Start with the seat frame:

First of all, the transverse crossbar and two segments of 350 mm are connected to each other. The crossbar should be located exactly in the middle of each line and perpendicular to them.
Next, 2 bent 780 mm segments are welded to the resulting structure. The place of welding is at the bend of the pipe.
At the next stage, the front parts of the supports are welded to the frame. In this case, the junction of the front supports with the seat base is 9 cm from their front.
The front legs are connected to the crossbar with pipes - for the strength of the bench.
The frame is almost complete. It remains to weld two arcs between the supports and the pads on the ends of the legs (supports).
The resulting structure should be sanded (welding places), primed and painted with anti-corrosion paint. At this stage, a garden bench made of a profile pipe should look as shown in the figure below.

If desired, the boards can be coated with colored paint, as well as replaced with metal rectangular pipes. We also recommend that you familiarize yourself with the video instructions on how to make a simple do-it-yourself shop from a profile pipe.

Benches from a profile pipe - furniture is reliable and unusual, but it is created much less often than wooden or plastic benches. The reason for this is the fear of a difficult construction task, because many do not know how to hold a welding machine in their hands, and have no idea how to connect metal pipes into a specific structure. However, this problem is solvable: you just need to prepare the drawings and strictly follow the instructions.

Metal profile as a material for a bench

Benches made on the basis of metal pipes have several advantages:

relatively low weight, in contrast to cast iron and concrete products, suitable only for parks;
low cost and wide design possibilities, which cannot be said about structures made of stone;
extraordinary durability, which distinguishes it from wooden benches, which deteriorate under the influence of weather conditions, bugs and mold.

A significant drawback of the metal pipes used to create the bench is their unaesthetic appearance. However, you can ignore this drawback, because there are many ways to decorate a metal product. No wonder the most popular benches are made on the basis of rust-resistant steel pipes and supplemented with wooden elements. A seat is usually made from wood, so that the bench does not heat up in the sun.

Gallery of benches made from shaped pipes

Bench frame - metal, seat and back - wooden The seat is made of planks stacked vertically The frame of the structure can only be made by a master Backrest and seat made of wide, painted planks The item is decorated with forged elements and a drop-shaped back Almost all elements of the bench, except for the seat, are made of metal profiles Armrests have been added to this item The design resembles an open book

Drawing up drawings with dimensions

They start making benches only after the drawings are ready. Schematic images will help you decide on the type of bench and find out how much material you need. To avoid mistakes in the manufacture of the bench, dimensions are put down in the drawings.

A metal bench without a back, the production of which takes little time, is created with supports - three rectangles, soldered to each other with two pipes - the seat frame. Such a structure can be 2.3 m long, 60 cm wide and 45 cm high. If desired, a bench made of metal pipes can be made shorter, narrower or higher.

If it is conceived to make a bench with a back, then you will need a different drawing. A design with an element that allows the resting person to tilt the torso back requires much more effort to be invested in the construction process. To build a bench with a back, you will need a lot of materials. However, most often they make just such a convenient version of the bench.

Selection of building materials

The main material required for the manufacture of a metal bench is shaped pipes. They can be of any shape, but the bench frame is best made from square or rectangular profiles. Pipes with flat outlines can be easily connected to any part. It is desirable that the metal profiles be cast from carbon or low-alloy steel - the most durable raw materials.

In addition to pipes, the materials for creating a bench are:

wood beams with dimensions of 50 × 80 mm, from which the back and seat are constructed;
screws having a diameter of 7 +/- 1 mm and a length of about 10 cm;
self-tapping screws fixing wooden elements;
enamel and primer that protect metal products from rusting;
antiseptic composition;
means for finishing wood and metal (for example, varnish and paint).

Calculation of the amount of materials

Usually, it takes at least 11 m of a profile pipe with a cross section of 30 × 30 mm to make a bench of medium size, because to create a bench without a back, the following parts are needed:

6 parts of a profile 60 cm long (long elements of rectangular supports);
6 pieces of 45 cm each (short fragments of the structure);
2 blanks 2, 3 m each (frames for the seat and fastening the supports).

In addition to metal parts, when creating a bench without a back, you will need wooden blanks:

8 rectangular bars 6 cm wide;
flat head bolts and nuts (16 each).

If you want to make a bench with a back, you will need to purchase boards with a thickness of 25 mm and 30 mm and at least 8 m of profile pipes with a cross section of 25 × 25 mm at a hardware store.

A pipe is a material for cutting fragments of the backbone of a bench, that is, the following parts:

a crossbeam located between the supports and equal to 1.55 m;
2 pieces of 35 cm length, from which the base of the seat is created;
2 bent parts with a height of 78 cm and a bending span of 10 cm, necessary to create the back and rear fragments of the supports;
2 metal parts 39 cm long - pieces for the front supports;
2 segments of 20 cm each, which serve as locks for the supports located in front;
4 support heels measuring 40 × 40 mm - ordinary metal plates;
2 bent metal strips 45 cm long, which solder the supports on both sides.

The following materials will be used to create a bench seat with a back:

3 boards 1, 6 m long, 60 mm wide and 25 mm thick;
3 pieces of wood 1.6 m long, 60 mm wide and 30 mm thick;
round head nuts and bolts (24 each).

Instruments

To make a shop from shaped pipes, it is customary to arm yourself with several tools:

an angle grinder equipped with wheels for cutting and sharpening;
electric drill with drills of different diameters;
a welding machine with electrodes with a diameter of at least 3 mm, which will allow you to easily solder metal parts with a thickness of more than 2 mm;
hammer;
electric jigsaw;
a machine sanding wood with sandpaper;
measuring tape;
a marker to make notes;
core.

If you plan to create a bench from curved pipes, then you will need a pipe bender. In addition to this, you will need a rounded metal profile template made from a piece of plywood - a tool that allows you to control the bending of paired parts.

Guide for the construction of a shop from shaped pipes

A bench without a back is a simple structure that is created in stages:

If the seat is intended to be made of metal, then rectangular pipes are used instead of bars. They are welded to the skeleton of the structure and treated with a coloring emulsion.

Other actions are performed when making a bench with a back:

The crossbar is connected by welding with two pipes 35 cm long. The rail, fixed between the two supports, is placed perpendicularly. It should be in the middle of both profile segments;
Bent pipe segments 78 cm long are attached to the metal structure. According to the rules, welding seams are created in places where the profiles are deflected;
The frame is supplemented with the front parts of the support, while the soldering point of the seat base and the supporting elements makes a place 9 cm away from their front zone;
The structure is strengthened by connecting the crossbar to the profiles that serve as front supports;
2 arcuate pipes are welded between the supports, after which linings are soldered to the edges of the legs;
Areas that have been welded are sanded with a machine, and all frame parts are primed. After it dries, an anti-corrosion paint is applied to the metal surface;
Planks are placed on a metal backbone. The back of the bench is made of thin wooden elements, and the seat is made of thick ones. The boards are bolted to the frame.

Wishing to make the bench comfortable and original, armrests are attached to it. They are 2 pipes, 75 cm each, bent with a special tool. The armrests are welded to the seat frame.

The easiest way to decorate a shop made of shaped pipes is to paint it. To do this, you can use not only standard black paint. It all depends on the wishes and possibilities. An additional decoration for a metal bench can be climbing plants planted around it, for example, grapes.

If it is assumed that the bench will be an element of the recreation area, then next to it you need to put a table made of plastic or wood. The bench itself is recommended to be placed near a reservoir, fountain or flower garden. A successful design option for a metal bench is the creation and location of a hedge profile near a structure.

When creating a bench for a children's corner, a swing or a sandbox should be placed next to it. If adults need a bench, then it should be placed in a gazebo or covered with a canopy. It is advised to put a blanket on the seat, which will make the metal bench soft. In addition to the bench, a table and a barbecue can be placed in the recreation room.

Video "Making a simple bench from metal profiles with your own hands"

A bench welded from shaped pipes looks no worse than a wooden product. But in order for it to meet expectations, you need to seriously approach the choice of materials and not violate a single point of the manufacturing instructions.