And surrounding walls.

It is very convenient for them to mask joints on the walls and on the ceiling, especially if they have different structures and are not too neat.

Its presence makes the design of the room clearer and complete.

Often people wonder: how correctly and carefully separate the room with the ceiling plinth?

This is especially true for those cases when the house owner prefers the repair performed by his own hands.

To make it right, it is important to strictly observe the existing recommendations and the rules of finishing work. And then the result will please you.

In the mount, the cartel (this is the name of this element) there are no difficulties: in fact, all the types of products are attached to reliable glue.

They are well treated with a special fine-grained hacksaw. You can also use a reliable web for metal. So how to trim the ceiling plinth correctly?

Ready factory angles

Note that each wizard has the opportunity not to corrupt over the exact cutting and fitting corners.

In a construction store, you can purchase a factory angular element in which the prepared baseline edges are easily inserted.

It is enough to measure the necessary length of the workpiece, and trim it at right angles.

All defects and flaws will hide this special element. But in such a convenient way to use it is not always possible, since the standard dimensions of such factory angles may differ significantly on the size of the baseline itself.

Such angles will be allocated by their disproportion, and it will not look very neat. But if the design of the room and the size of the blanks allow you to use this method, then they should not be neglected.

The same, who will have to take advantage of one of the ways of trimming the ceiling plinth, the following tips will be used.

Pruning cartel

Trim using stusl

How exactly crop the corner of the ceiling plinth with it?

Stupil is called a simple tool that carpenters use. With it, you can cut any billet under the desired angle.

It is usually a wooden, metal or plastic tray, on which they are made for cutting at an angle of 45 ° and 90 ° Special vertical slots.

There are complicated constructions, on which plus to these corners there is also a hole for the implementation of a 60-degree cut.

For professional work, a special stub is produced.Its rotary mechanism allows you to fix the cutting canvas in relation to the workpiece at any given angle.

Internal corner

Cooked applied to the ceiling, the desired length is postponed.

Then this strip is inserted into the stubble exactly as it will be located on the ceiling. It must be pressed to the far wall of the device. In this position, the plinth is held with his left hand.

The canvas of the hacksaw should be in this position so that its angle is 45 degrees, and the handle would most closely come closer. Trying to avoid push on the saw, gently cut the workpiece.

Similar to the previous procedure, the position of the hacksaw - its handle gets closer with hand at an angle of 45 degrees. Plinth is cut.

Then ready, already cropped strips are docked - the precision of fit is checked. It is believed that for better orientation, in the manufacture of an inner angle, it is better to cut with the front of the product. Sections of sections usually have to be customized with a file.

Outdoor

It is more correct to keep more accurate sizes, first start posting the inner corner, and only after that move to external.

Otherwise, it can happen that along the entire length of the plank will be not enough.

The bar is applied to the ceiling, the size of the mark is made. Holding to the left hand, the ceiling plinth is pressed to the near wall, the handle of the hacksaw clings to the hand. The billet is cut off.

The retaliatory bar is pressed to the nearest wall, while it keeps his right hand. The hacksaw blade should be at an angle of 45 °, the handle of the tool comes closer with the hand of the wizard. A piece of workpiece is cut off, the angle is neatly docked.

Such treatment with the edge of the parts using the wort is good in those cases if the angle between the walls is smooth and straight (90 °).

If his performance leaves much to be desired, then it is worth using a different method.

How to cut the ceiling plinth without a stub?

Marking on the ceiling

The method with marking on the ceiling allows you to cut the angle exactly and smoothly. He has one drawback - the bar is quite inconvenient to keep weight during the procedure.

In everything else, with this method, you will be able to outline the cutting angle even more exactly than others.

When the plinth is applied to the intended installation site, all the deviations of the sizes and inaccuracies are noticeable and immediately taken into account.

Circumcision of the corner

First you need to take a pair of blanks, then crop them at right angles. Breaking the end of the plank to the perpendicular wall, we apply one bar. Delated on the ceiling line along the plinth contour. We remove the first bar, then also, resting the end to the wall, we apply a retail bar. Similarly, we note on the contour line.

The intersection point of two individual lines is a mark on which the workpiece is cropped. Each plank is applied to the surface again, the point of the future cut is noted on both. From the found point to the other edge of the plank of the plinth to the line. Plinth cutting on earlier marks, carefully docile, we have to install them.

This method allows you to more accurately process the internal angles.

How to make a stouch pattern with your own hands

If you do not have a stouch, do not necessarily buy a tool for one-time use. The template with similar features can be made independently.

For this tree, paper or cardboard, the desired cutting angles are applied.

Then you need to draw a pair of parallel lines, find the center, after which it is possible to measure the angles of any given value using the transporter.

This method is especially convenient because, using it, you can postpone the angle of any size, even more direct.

The method of processing a plinth workpiece using a homemade tool is practically no different from working with the original. The bar is pressed to one of the parallels, after which the knife is installed at the desired angle, and is cut off.

Remember that before cutting the corners of the workpiece, it is necessary to check the corner value between the walls! This uses the vehicle and a corner.

How to trim the ceiling plinth correctly. Important little things

The measurements needed to trim the plinth on the ceiling should be done in a special way.
To determine and mark the inner corner, the length must be measured from the corner itself. For the outer corner mark, it is necessarily taken into account that the depths of the plinth will perform a distance that is equal to its width.

Planks of plinths are not desirable to fasten until it is about their exact location and cut the return plinth.
Only after the ideal convergence in the corner of both renewal slats, you can start their installation and fastening. If work is conducted with polyurethane or wooden plinths, defects and flaws can be fixed with a saw or file. To fit the product from

Dear Lord Builders. I would like to know the detailed process of the correct alignment of the walls (reinforced concrete), the composition like Knauf ... In this case, I am a kettle, but I want to make a bedside of my daughter, but there is no money to lay out professionals for work, and there is no guarantee that Good pros ... So I want to know what yes, how, and how much is a pound of lich. Thanks for the advice. The walls will be aligned for the further paint of paint Shervin Williams.

• 1,874 response

Now we are doomed to the counters of all and all. Dolbanuted "craftsmen" immediately rushed to teach all twisting water. And then the "typical scheme" of the installation of a hydrochloride was born, which includes a valve that prevents manipulations with the instrument. Because of these valves, the problems with boiler were climbed and rushed through the forums of the moans and panic screams - "Ahtung! Growing pressure in the heating floor! What to do?" There would not have been this valve - there would be no problems. And manufacturers and merchants began to sell on the so-called "security groups". But this is another topic ...

• 37 replies

Hello, brothers in repair! Long time I did not write anything here, and indeed it rarely began to go, everything is somehow underwritten: then a booze, then a goulock, and now the new "attack" attacked me. But knowing that you, despite anything, do not remember me, I decided not to be a pig, and tell you about my new hobby. I will start from afar: almost all my conscious life I worked as an electronic engineer, and the engineer-developer engineer of electronic and electrical devices of the widest class and destination, and at the same time purely in the "defense". It is clear that the scope of my amateur interests was limited only to my lazy, no restrictions in radio components simply did not exist for me, I had everything! Well, by following the trends of the then amateur radio fashion, I am the main emphasis on the radio and amplifiers, Esno, on transistors and chips. I have not worked for a long time in this area, and the details have long rose everything for a landfill, but in my soul, I had a dream all this time - to make a lamp capacity, but not simple, and so that everyone is frown. And I must say, at work I was most of my time dealt with electrical accomplices, radiologists, if on simple, so this topic was well acquainted for me. And then this fashion on the "warm lamp sound", according to which the people are literally crazy. In short, a year ago I decided to realize my dream of life. Immediately determined: mainstream, ordinary lamp amplifiers with a weekend transformer, I'm not interested, not the royal business! And whether to improte me a bopedransformed tube amplifier. Well, the difficulties on this path I represented myself well, and thoughts some of our own were on this bill, but still I decided to consult with the guys-radio amateurs. I found a suitable group on Facebook, I myself began to publish it, and somehow asked a question on the topic: Will I tell me who a scheme of such an amplifier will tell me. And I immediately give up a link: http: //hifisound.com.ua...a-6s33s-otl/ (I hope I did not violate any forum rules, leading here a direct link, especially since it is from a completely different area? ). I will not tell about this scheme, if anyone is interested, I can then explain what's happening there, just say that this scheme immediately interested me, and its unusualness, and the potential opportunities that I saw it. I decided to start. And where to start: details - 0, there is a soldering iron, still Soviet, and the Ketai tester. But, Likha trouble - the beginning: I was leaning on Avito, on Ali Express, went a couple of times on the Mitin Radio Radio, began to turn to the Radio-Dogeon Barahl. ..

Now I'm going to dangulate, and I will continue, if I wonder, already with pictures ...)))

Show that something different from the tables in the blog, otherwise I have not been long ago.

Children's topics recently captured me not by childish. Different objects were asked to make a garden.

The first object, educational, necessary and useful. This traffic light, the children will study the rules of the road, the thing is archiving.

Immediately make a reservation, the version of the pedestrian with the little men also did, but more simple from the cardboard.

In principle, this is three glazing asked to make a cardboard simple, but unless I can do without problems)) I thought, and did not make a reliable learning subject, and did. How long enough.

The concept of the figure is such, quite large so that everything can be seen, steady, durable and with a turning mechanism, the meaning is that there are 4stores, one side shows all signals for a general understanding of the device.

Three other sides by one signal, the educator can turn and show any color out of 3 and asking the kids about his purpose.

In general, I thought it seemed to be correct

The initial thoughts about the color circles on magnets and other light bulbs had to cancel, you need a simple, understandable solution that is difficult to break, mugs of magnets may fail, battery bulbs fail.

Whether the idea turned out and I do not know, but time will tell.

The whole basis is MDF, which cleaned the PVA, for temporary tack, also fastened the microclemp.

Separately, I note that it is possible to make circles of different diameters on the circular, and the main thing is the same, with the help of not a cunning device, first cut the square blanks, and then on the device rotating the part to cut the corners to the polyhedron, and then rotate the part to the circle.

Bluccuke smoke, the visors are halves the glazes of the circles, there was a groove with a molebl, so in the end such things are not safely incisible.

The whole thing rotates on the pipe from the Joker system in my opinion for the racks, so that it does not fall out and the stops are not falling out, which clusted fixed.

The base made the massive and wide of thick layers of MDF, with such a base, the traffic light is not so easy to figure out on the side.

I put the fool and drilled through the pipe, I had to flip the plate from the return.

Painted everything from the can, then covered with varnish, the thing is ready.

Circles-signals did not paint, they are cut out of the paper of self-keys, it is easier to update the demonstration subject.

Who read, watch slides

At the final stage of the floor arrangement, the fitting place of the finishing coating to the walls of the room is usually closed by plinths. The largest popularity has recently been predicted with plastic products. They are not only aesthetic and diverse, but also very functional. The question of how to cut the plinth plastic, arises from any domestic master who has collided with this procedure for the first time. Tools and devices for such work are fairly simple and are quite accessible.

Advantages of plastic products

Compared to its analogs of wood or MDF, plastic plinths have a variety of benefits. Their undoubted advantages include:

• Durability and durability.
• Moisture resistance. They are suitable for installing indoors with high humidity (bathrooms, shower cabins and toilets).
• They do not need to paint or apply another protective coating.
• The construction market presents a huge selection of colors: from a variety of one-photon to imitating the structure of expensive wood species. Easy to pick up the cartel for any interior solution of the room.
• Easy processing and mounting to the wall.
• Convenience with subsequent care. The only limitation is: it is unacceptable to apply abrasive cleaning agents that can scratch the upper decorative layer.
• Affordable price.
• Safety for human and animal health. All modern polymeric materials of this destination are manufactured in strict accordance with sanitary standards and requirements.

Varieties

There are several types of plastic plinths for the floor depending on the material of the finish coating:

• Special profile T-shaped for framing floors with carpet flooring. For decorating such products, strips are applied, sliced \u200b\u200bfrom the floor coating, which are fixed using bilateral tape.

• Mr.-shaped products specially designed to fix linoleum to the walls.

• Universalwhich are suitable for floors from a variety of materials (from tiles to laminate or parquet board).

According to the functional features, such products are:

• c equipped inside cartial cable channel (one or more) for laying wires of various purposes (telephone, antenna, computer or electric).

• with pressed rubber stripes At the edges for dense adjunctions to walls having roughness and irregularities.

By geometric sizes, the choice is also quite wide. The width is the cartel, which is usually selected, commensurate the height of the ceiling of the room, can be from 40 to 150 mm. The standard length is 2 or 2.5 m. The profile thickness in the lower part depending on the design is in the range of 10 ÷ 38 mm.

Tools and devices

With the arrangement of the finishing framing of the floor, there are three main issues in any home crafts.

• What to cut
• How to do it neat and under the necessary angle?
• How and how to fix the chopped pieces to the wall?

Cut the long products to separate parts of the required length can be using:

• bulgarians (with a thin cut-off disk);
• electric jigsaw;
• manual or with small tempered teeth).

The final choice of how to cut the plinth plastic depends on the tool, personal preference already existing in the presence.

For reliable fixation of cartel to the walls of the room you will need:

• perforator (with a brown of the required diameter) or an electric drill (with a shock mode of operation);
• a set of dowels and screws;
• screwdriver or screwdriver (for saving time and strength).

For accurate dipping of pieces at the desired angle, you will have to purchase a stub (of course, if it is not in the household). Without it, it is impossible.

Stuslo: varieties and ways to use

A stubble for cutting plastic plinth is a special device intended for a neat cut at a certain angle. The simplest products are made of wood or plastic. In geometric shape, they are a segment of an inverted P-shaped profile. Side walls have narrow rods for a hacksaw blade. The most common devices until recently were tools with three propuls, allowing to trim the block of plinth at an angles of 45 ° and 90 °. However, the layout of modern apartments is very diverse and often the need to exercise various corners of the premises. Therefore, manufacturers produce products with a large number of slots intended for the installation of a hacksaw blade at different angles.

The price depends on the size and material of the device. So a plastic device from Stanley with a length of 310 mm, 130 mm wide, 78 mm, and the possibility of sawing at an angles of 90 °, 45 ° and 22,5 ° costs 750-800 rubles.

The application algorithm is quite simple:

• With the help of the marker and the line, we apply the markup of the cutting line.
• Tightly press the profile to the vertical wall of the device so that the markup clearly coincides with the place of installation of the saw.
• Gently screaming.

You can carry out a cutting of a plastic plinth with a metal with a metal. This tool has its advantages: small cutting teeth and a small divorce. However, the low longitudinal rigidity of a narrow havice canvase can adversely affect the quality of the treated surface. It is better to apply special (with a wider and rigid). Challenged teeth will easily cope with plastic.

More complex structures are a base with clamping clamps (for fixing the work being processed). The kit already includes a saw installed on special guides. The cutting angle can be adjusted over a wide range. Materials for the manufacture of base are metal or shockproof plastic. But such devices are already more expensive. So, popular swivel models from Gross or KWB with a double-sided saw (size and sharpening of the teeth for various materials), depending on the size, it is already 2200-4700 rubles.

Use such devices is very simple:

• exhibit the required angle;
• the peller is pressed to the bed with a clamp, so that the markup is strictly under the blade of the saw;
• we make cut.

And even if you decide to make repairs only in the same room, it is worth thinking about to take such a device to hire and do not think than cutting the plinth plastic. Ease of use, speed and processing quality will pay off the expended means of full.

How and how to fix

The easiest, least labor and fairly reliable method of fastening is the use of universal quick-drying adhesive compositions of the type "liquid nails". The disadvantages of this method include:

• When dismantling (if necessary), the product will most likely be spoiled, so initially it goes into the discharge of "disposable".
• The inner surface of the cartel must have a fairly wide flat strip to possibly apply the required amount of glue.

If the fasteners are included in the package of plastic baseline for the floor: metal (or polymer brackets) or special long profiles, then they first fix them with the help of dowels and self-tapping screws. Further installation is pretty simple. The product is neatly snapped into already fixed devices. This method can be attributed to the advantages of this method: the possibility of repeated dismantling (especially it is convenient when changing wallpaper: the bottom edge of the wall design can be started behind the plinth).

The presence of a cable channel with a decorative outer bar allows you to simply screw such a perch to the wall through pre-drilled holes.

Docking individual segments

When installing polymeric quilt, they must be reliably and at the same time to aesthetically docile on the corners of the placed room, and sometimes on the straight section along the long wall. The best solution to the question of how to dock the plinth is the acquisition of the required number of special products. Almost all manufacturers of goods for edging flooring produce these small, but very convenient and necessary "detail" of various geometric shapes:

• for the arrangement of internal and external angles;
• for horizontal docking of straight segments;
• for sealing ends.

These devices are either just snapped on the ends of the profile using special mustache; Or in places of their installation, the walls are fixed by brackets, and then the connecting elements are fixed to them.

Methods for cutting ceiling plinth for dusting in inner and outer angles using a stouch, template, or wall markup method. Tool selection rules and useful tips.

The content of the article:

One of the most difficult steps when installing ceiling plinths is their correct cutting. Only competently docked the individual elements on external and internal angles, you will get the desired result. Aesthetically, the cartel will look like, if they cut them off at the desired angle and close the gaps. To perform this task, a special tool (stub) is used. And if it is not, then other devices will help.

Selection of tools for cutting ceiling plinths

To properly and gently cut the ceiling plinth, you need to use a tool suitable for cutting. It is chosen depending on the material from which the cartarets are made:

• Styrofoam. It has a low strength and is relatively inexpensive, and therefore foam models are becoming increasingly popular. Their strength does not particularly affect the operational characteristics, since the ceiling plinth is not subjected to mechanical loads. For cutting suits the usual stationery knife.
• Extruded expanded polystyrene foam. A cheap material in which the density is several times higher than that of the foam. It is a bit more complicated to cut it because of this, and therefore for this purpose a sharp and thin knife is used.
• Wood. Such plinths are more difficult to process, even have many advantages (ecology, strength). They cost more
  especially if made of hardwood. Before cutting the ceiling plinth of wood, pour with hacksaw.

In addition to the tool for the direct cutting of the baguette, you will need stub. This is a special device made of wood, plastic or metal in the form of a box with climbing sidelines. The hacksaw or knife can be inserted into it under the desired angle. Thus, the cutting angle is obtained as accurate as possible.

It can be purchased in a construction store or make it yourself on such instructions:

1. Three shocks 50 * 15 cm are pinned with a long edge into a trilateral, rectangular box. Note, an angle of 90 degrees should be followed between the side bars and the transverse plate.
2. With the help of the transport, we mark the angle of 45 degrees on the bars. Instead of transport, you can use school square. In it, one angle is 90 degrees, and the other two are 45.
3. Before cutting angles, we note the vertical direction by a simple pencil.

To work with this homemade device, it was convenient and safe, a plank before the bonding is needed to stall.

Ceiling Plinth Cutting Technology

For prompt and high-quality work, you need to choose a tool in accordance with the plinth material and select the cutting method. If you have a stub, then there will be no special difficulties in the process. If it is not, then two options are possible: cutting on the template and measurements on the ceiling or make this tool yourself.

Features of cutting ceiling plinths in the stub

It is necessary to work with this device extremely careful not to blow up the tool and do not leave the location in unnecessary places. In the process, adhere to the following instructions:

• Fix the baguette in the stupid in such a way as planned to be placed on the wall. The side that will be pressed to the ceiling on the stupid should be seamless to the sidewall.
• Insert the cutting tool into the desired gap (knife or knife) and cut the quilt.
• We process the seat of the ceiling plinth and apply to the wall to check the correctness. The foam molding can be adjusted with a sharp knife if the end of the end is about 2 mm. Wooden plinth can simply be ground with sandpaper. For ease of use, it can be glued to the wooden bar.

When cutting and hanging products from foam and polyurethane, remember that these materials crumble and praise, because the tools must be quite acute, and the strong mechanical impact on them is undesirable.

Technique cutting ceiling plinths by template

This method can be used if you have smooth angles, and it is required to trim the baguette at exactly 45 degrees. For this, before cutting the ceiling plinth in the corners, you need to draw a stood on thick paper. We carry out two parallel lines and mark the corners under the desired degrees using the transport.

We place the quilt in this case in the same way as on the traditional stouch. Note that you need to cut the plinth, keeping the tool in a strictly vertical position.

Rules cutting ceiling plinths on markup

This method is used to cut the plinth in cases where there is no stouch, no details from which it can be made.

To do this, make marking on the wall in this order:

1. We apply the baguette to the angle to the location of the fastener.
2. According to his one edge, we spend the baseline on the ceiling for the fastening level.
3. Apply the same way in the perpendicular line on the ceiling and re-spend directly on one side. We must have two segments that intersect at one point.
4. Apply again in turn two plinths and celebrate this point on them.
5. We repeat the same procedure on the wall now to designate the place of cutting space from the bottom.
6. We connect two points of the line. It can be held at an angle of 38-45 degrees, since the walls and corners in residential rooms are often uneven.
7. Cut the baguette on the conducted line.

Performing cutting in this way, it is important to precisely carry out all lines and mark points. Error even a few millimeters will cause the formation of a slit. This method is suitable for cutting and dusting both the inner and outer corner of the ceiling plinth.

The method of cutting the ceiling plinth without stub

To carefully dock in the inner corners, you can do without a stub.

Perform work in this order:

• We apply the end part of the baguette to the sheet of paper and circle the convex side circuit. It is more convenient to use a small plinth segment (if any).
• Cut the resulting pattern.
• We carry out the contour to the surface of the baguette by a simple pencil.
• Cut on the curve spent.
• For example, one plinth applies a tight end part to the wall, and then the second.
• If there are small gaps, they can be treated with a stationery knife or ease the sealant.

When working with stupid, two points should be taken into account:

1. The inner corner of the ceiling plinth is formed from two elements: the first we turn to the right in the stub and cut to the right left, the second we turn to the left and cut to the left right.
2. We bring the first part of the outer angle to the left and cut to the right left, the second we will start the right and cut off from left to right.

In addition, you need to know such nuances before performing the cutting of the plinth:

• Before you begin to cut a baguette using a stub, try to cut off the trial to prevent errors.
• It is possible to correctly make measurements, measuring the length of the inner corners of the bar on the inner side, and the outer - from the point of the inner angle to the width cartoons of the enclosure.
• If the baguette is installed under the stretch ceiling, then it should be attached only to the wall. The adhesive composition in no way should fall on the vinyl cloth.
• The final attachment of the plinth must be carried out only after an accurate planet reject.
• If the corners and walls in the room are smooth, then the adjainment can be done on the floor.
• When installing baguettes, there may be a need to customize them several times, because tool and patience.
• Instead of the template and stub, you can cut the corner between the wall and the floor, or moves the table to the wall. In this case, on the wall, ceiling and baguette, it is necessary to mark the angle of cutting the end.
• If you are interested in the question of how to cut the ceiling plinth without a stub, and on the use of templates you do not have time, you can pre-purchase special angular inserts in advance. They will hide the gaps, but will perform and stand out on the coating.
• If you have a plinth of the valuable wood, it is necessary to cut and install it very carefully, since a large amount of putty for sealing the joints will be too noticeable, but to paint the baguette - an inappropriate solution, because you hide the natural texture of the array.
• The polystyrene foam products are not necessarily customized to each other from the softness of the texture, but the wooden and plastic models must be well docked.
• If the trapezoidal niches on the wall required from the top to bypass the plinth, then wech the silence at an angle other than the direct.
  Plinth cut off in this case at an angle equal to half of the joint. For example, if the walls are joined at an angle of 120 degrees, then dug a quiller at an angle of 60 degrees.

How to cut the ceiling plinth - Look at the video:

An indispensable part of the room design of the room is the plinth. For example, plastic products gradually replace wooden. Functionality and convenience are inherent in this finishing material, and it creates aesthetic flop of the wall to the floor or to the ceiling. In cases of lack of ultimate processing containing the presence of plinth strips, which seem even sustained in one-style offices. The problem lies in a loose adjuncing overlap on the floor to the wall. It forms rude seams that are eliminated by plinths. Fixation is easily feasible without the help of professionals, it is based on knowledge about whether to cut plastic plinth and which ways to install.

With what is the pruning material? This question matures almost any beginner builder. The selected cutting tool will affect the evenness of the edge of the saw. Polyvinyl chloride plinths contain a structure with a full filling, so the use of a toolkit containing a large teeth or a wide wave is not welcomed due to the large risk of chipping and numerous irregularities.

For a plinth cut, it is better to use the metal hacksaw. Its structure is characterized by a sharp rather small teeth and permissible width of work. Using hacksaw applies only to panels. The thin-walled plinth will acquire an uneven form due to the effect of teeth.

Hand Lobzik is the best tool for cutting the corners of the ceiling plank.

Any plastic product will be cut absolutely smoothly. But, the jigscription has a disadvantage - a slight size. This will greatly affect the speed of repair work due to a large number of cloths. Abrasive files should not be used while working with jigsaw, since the first tool will complicate the entire procedure.

The thin-walled plinth is better to cut with an ordinary stationery knife having a fortified blade. Obtaining a clear and even slice will occur only if there are great experience with the instrument and material of this species, so that beginners will have to be quite difficult.

Cutting stusl

Geometrical forms are very important for proper trimming. Compliance with this condition is necessary in order to form an ideal mounting seam in the middle of the panels. When conducting this procedure "on the eye", the result will not be able to console a qualitative view due to the inconsistency of the parties to each other. This is the most important importance for the formation of internal and outer angles. Consequently, the ideal trimming is obtained using a stouch that allows you to measure the angles of 45 degrees.

The device with slots with a location corresponding to the used angular point of the cut is characterized by a form like the letter "P".

Cutting using stupid occurs in this way:

1. The central notch in the instrument is designed to fix the plinth in it. The panel material is applied to the surface of a draft-draft. If you make the opposite, then damage to the facial part is possible. Diagonal slots are guides.
2. The desired angle is the next stage when choosing. It is necessary to track the position of the edges of the panels. They should not go beyond the diagonal slot. Exceptionally so it will be a cut of an excellent quality. With a large depth of a stubborn tray, which is highly different from the size of this plinth, it is necessary to uniformly pressed the panel to any groove side. Only after that you can make the cutting process. The angle should remain constant. If this is not respected, then at the end of the proceeds done, we get different in the form of the figure. Due to the elastic PVC structure, excessive pressure on the plinth will spoil the cutting quality. The tempo of the saw should not go beyond the framework of moderate due to the risk of overheating and deforming the boundaries.
3. Due to the split works of one side, it should be proceeded to the formation of another. You need to act by the same instruction, only using the mirror image of the angle. To return the angle of cutting, the material should be placed in the opposite recess.

Cutting on stencil

If the corners of the walls do not correspond to the standard parameters, then the stencils can be used. For this, stripes of fine cardboard or tight paper are used, from which the strips are cut out, which in thickness correspond to the selected plinth. They are applied into the location of the angle and are fixed there, then the unnecessary part is cut off with the help of a stationery knife. It is necessary to cut a perpendicular to the intersection of walls so that in the end you can get two absolutely identical parts of one corner. The shame is used in case of inconsistency of the wall angle standard. Cardboard with a fine structure or dense paper take part in the creation. You should cut the strips with a thickness suitable for the selected plinth. Cropped piece should be applied so that its unnecessary part is cut off with a stationery knife.