Gasilicate blocks are one of the most popular building materials in the modern market. The buildings were elected from them are characterized by durability, attractive appearance and excellent performance characteristics. But, of course, to construct high-quality walls from such blocks only under the condition of the right choice of the fastening mixture. In our market, there are several types of such a means as glue for gas-silicate blocks. Consumption on 1m3 of these funds can vary significantly.

Solution or glue?

Sometimes gas-silicate blocks are simply placed on however, this method of erection of walls is used only in extreme cases. The advantage of gas-silicate blocks is primarily the fact that they are able to preserve heat indoors perfectly. According to this indicator, such blocks are not inferior to even popular wood. Low thermal conductivity of gas silicate material is associated primarily with its porous structure.

When using a conventional cement mortar in a masonry from such blocks, it arises and this, in turn, reduces the main advantage of the gas silicate.

When using adhesive compositions, building blocks of this species are stacked by special technology. The fastener is applied to the ranks and between the individual elements of a very thin layer. As a result, no cold bridges arise in the masonry. Sometimes such mixtures are applied rather than a thick layer. But in this case, their composition necessarily include special additives that increase their heat-grinding qualities.

Modern glue for gas silicate blocks: flow per 1m3

There are funds intended for laying gas-silicate blocks, in most cases relatively inexpensive. But, of course, before buying such a composition, it is necessary to make the calculation of its required quantity. Consumption of adhesives for gas-silicate blocks of different brands can be very different. Some adhesives are applied in laying with a layer of 5-6 mm, others - 1-3 mm. Permissible thickness The manufacturer usually indicates packaging. Also in the instructions in most cases there are information about the estimated flow rate of 1 m 3 of masonry.

Make all the necessary calculations, thus, if necessary, it will be completely unclear. In order to find out the right amount of the mixture, you must first calculate the total volume of masonry. For this, you will have to simply multiply the thickness of each wall, and then fold the results obtained.

In most cases, glue consumption for gas-silicate blocks according to manufacturers is 15-30 kg per 1 m 3. That is, a masonry cubometer at the master should be about one bag of the mixture. However, unfortunately, manufacturers usually slightly underestimate the flow rate. In fact, most often when laying on 1 m 3 leaves 1.5 bag of the mixture.

Characteristics of adhesives for gas silicate blocks

The basis of such compositions is very often the same cement mixture. However, in the manufacture of adhesives of this species, manufacturers are usually added to them, in addition to standard components, and special substances that increase their plasticity, moisture resistance and frost resistance. Also, the solution for gas-silicate blocks often includes additives intended for improving heat grumbling qualities.

They are such funds in most cases dry mixes, packaged in bags. The preparation of glue of them is made simply by adding water in the desired quantities.

Thus, simplicity is used - this is what, among other things, features glue for gas-silicate blocks. Prices for such compositions are usually not too large and quite comparable to the cost of a standard concrete solution.

Types of glue for gas silicate blocks

All the compositions implemented today in the market designed for laying this material are divided into several varieties:

adhesives used to build partitions and walls inside the building;

compounds intended for masonry outside;

universal mixtures, apply which is allowed both in rooms and on the street;

mixtures with increased swelling speed;

building glue, designed to masonry the enclosing structures of those buildings, operated which will be subsequent in conditions of high humidity.



Glue manufacturers

Of course, when choosing the most suitable for masonry of walls from gas-silicate blocks of the composition, attention should be paid not only to its specific purpose, but also on the manufacturer's brand. Many companies are delivered to the domestic market today. The most popular brands of adhesives from Russian developers are:

"Unis Tea Unibok".

"Best of Selform."

"Prestige".

"Teplit standard.



Unix compositions for cellular concrete

The laying of gas-silicate blocks on the glue of this brand can be made both indoors and outside. It is also allowed to apply Unix for sealing chips in cellular concrete. Correction the position of blocks when using this composition is possible within 10-15 minutes. The advantages of UNICS glue consumers include including the fact that he is distinguished by the heat grumbling qualities, as well as

Also, the plus of such mixtures is the resistance to moisture and very low temperatures. According to the manufacturer, Unix Temple is an absolutely environmentally friendly product. The recommended layer of its application is 5-10 mm.

Another unconditional dignity of the adhesives of this brand is their availability. You can buy "Unix toilet", in contrast to the mixtures of many other manufacturers, you can practically at any building materials store.



The mixture "Best of Selform"

This summer glue is made on the basis of cement-sand mix. Consumer reviews He also deserved a relatively good. Its unconditional advantages, among other things, include low cost in good performance. In order to make the appropriate properties, the manufacturer adds special substances to it that increases its heat-grinding qualities.

The thickness of the masonry seam when using the mixture "Best of Celmord" can be 2 mm. The benefits of this glue should also be attributed to the fact that it is capable of penetrating into the smallest excavations and irregularities of the blocks, which, in turn, increases the strength of the clutch. It has another unconditional dignity of this glue for gas-silicate blocks. The flow rate of 1m3 is only about 25 kg.



Ytong

Adhesives of this brand are pretty expensive. But the characteristics are simply excellent. Apply to YTong on blocks can be layered only 1 mm. Therefore, his consumption is very small. The mixtures of this brand, in addition to cement, include polymers, mineral supplements and special substances that give it plasticity. The advantages of Ytong Adhesives are among them and their ability to quickly capture. Also the advantage of the mixtures of this brand is the high degree of frost resistance. It is possible to use such adhesives in the erection of enclosing structures in the winter season.

Mixtures "Etalon Teplit"

Like "Unix", such compositions are found quite often. The advantages of winter glue "Etalon Teplit" consumers are primarily a high degree of plasticity. Being applied to the gas silicate, this composition is not resolve and does not spread. Store this glue after cooking without loss of quality can be several hours. At the same time in the masonry, it is grapped literally for 10-15 minutes.



Reducing the cost of construction is also something that this glue is appreciated for gas-silicate blocks. The flow rate of 1m3 is only 25-30 kg.

Tools "Prestige"

It is also a very high-quality mixture, which can be used both in the warm season and cold. The unconditional advantages of these compositions are primarily a high degree of plasticity and reliability. The viability of the Glue "Prestige" preserves within 3 hours. You can apply it to blocks with a layer of 3-6 mm thick. Full strength climbing the mixture reaches through three days.

Glue for gas-silicate blocks: prices for funds from different manufacturers

The cost of compositions intended for laying gas-silicate blocks may depend not only on the brand, but also from the supplier. The price of glue "Unix" is, for example, 240-260 rubles. per bag of 25 kg. For the same amount, the means "basics of charm" will need to pay about 200-220 rubles. YTong glue costs about 310-330 rubles, and "Teplit standard" - 170-200 rubles. For a bag of 25 kg "Prestige" will have to give only 130-150 rubles.

The glue is considered a mixture of substances that allows you to securely clutch materials. And so that the seam was strong and durable, the quality product should be applied. To secure gas-silicate blocks you need a special glue. This composition usually contains sand, cement, as well as organic and mineral plasticizers.

Currently, a large range of funds is presented to work with gas-silicate blocks. The result of the selection of such a composition is influenced by the preferences of the masters and the conditions for conducting styling work.

What to choose a mixture for laying blocks

To recognize which glue for the gas silicate is the best, it is worth considering buyers' reviews that have already managed to check the material on your own experience. Let us dwell in detail on the brands of the glue that scored the most popular.

"Obudova"

This mixture is great for mounting blocks in the winter. This is possible thanks to the ingredients included in it. There is a special additive, not exposed to even fierce frost (frost-resistant). Most builders respond positively about the product, because it possesses such advantages as the ease of application and elementality in the application. In addition, the glue "Obudov" is inexpensive, which provides him with the position of the leader among all the finished dry adhesive compositions.

"Prestige"

This mixture is also not afraid of frosts. It is used for laying blocks from cellular concrete, as well as plates. The characteristic advantage of glue is the speed of its preparation. By savings, this composition is slightly inferior to the first, since its value is slightly higher.

Bonolit.

Such a composition for a gas-silicate block is allowed to use both in summer and in winter. The main advantage of its advantage is environmentally friendly. The glue does not contain unwanted impurities and toxins, absolutely no danger of human health. Perhaps this affects its cost, because it is more expensive for previously discussed options.

To date, this building composition is actively used when laying gas-silicate structures. The glue reputation is conquered by its positive properties:

1. Excellent thermal insulation characteristics of the mixture make it the most similar to the cellular concrete. This will be allowed to forget about the frozen walls and heat leak through the connections in the masonry.
2. The composition does not lose its properties even with direct contact with water, as well as the effect of very low temperatures.
3. For the implicated solution, excellent plasticity is characterized, which makes it applied comfortable.
4. The mixture is completely environmentally friendly. There is no extraction of toxic substances, since the product does not contain harmful impurities.
5. The composition is more expensive than previous products, and this is due to its qualities.

Aeroc.

For mixtures of this brand, high strength indicators are characterized. The composition is used everywhere in masonry blocks from a cellular material, as well as for cladding a thin layer of blocks of internal and external surfaces. It turns out the seam with a thickness of 1-3 mm.

The glue is very popular thanks to the following properties:

• in the masonry there are no "Bridges of Cold";
• not exposed to moisture;
• not afraid of harsh frosts;
• you can use the prepared solution for two hours, during which time it will not freeze;
• capably skid steam.

The high adhesion of the mixture allows for monolithium and high strength of the buildings. The glue consists of cement, mineral fillers, as well as organic and polymer modifiers.

"Win"

It is a multicomponent dry mixture based on cement, quartz sand and different modifying increases. It is used to masonry silicate block structures. Glue is quite suitable for summer and winter work. The material is popular, as it is compatible with the majority of Russian gas production.

The finished solution is highly elastic and technologically, not very lipot to the tools. The applied layer is characterized by good moisture resistance. Glue has an excellent holding ability.

Mixtures of this brand are used to perform thick-layer masonry in the winter and summer seasons. In addition to laying blocks, they are used everywhere in the installation of ceramic tiles, fastening it to blocks. When applying the composition, it is not necessary to level the surface. You can leave the slopes and drops to 1.5 cm. Often used for works indoors for alignment of walls from blocks.

All compounds presented are safe, endowed with good plasticity and are able to withstand strong frosts. What a mixture is best suited, you decide when you exploring them with an experimental way.

The answer to the question of which glue is best of all, is ambiguous. The fact is that we presented the best adhesive mixtures, according to the builders who checked all their advantages and disadvantages in the work. Selection of glue can be carried out not only on the basis of personal preferences. Be sure to take into account the type and conditions of laying work.

How to calculate glue

The dry makeup is packaged by the manufacturer in bags weighing 25 kg. Such a number of manufacturer chose not by chance, since it is the optimal mass of powder for the preparation of glue, sufficient to lay a single cubic meter of blocks. This is provided that the production technologies of the mixture and its use are not violated.

Let us clearly understand the calculation of the flow of adhesive on the example:

1. Initially, you approximately determined that for the laying of all the walls you will need, suppose 63 cubic meters of gas-silicate blocks.
2. With a layer thickness of 3 mm, the glue consumption per 1 cubic meter of blocks will be 63 packaging bags.
3. If the seam is 2 mm thick, then the mass of the necessary adhesive will be less than 5 kg. In this case, 63 cubic meters will have to spend
   63 x 20 \u003d 1260 kg of dry glue.
   Go ahead.
   1260/25 \u003d 50.4 bags.
   Rounded the indicator in the biggest, the result is 51 bag.
4. The value derived as a result of calculations is the smallest amount of dry mix that will need to spend on the building. Provided that its construction implies the use of 63 cubic meters of aerated concrete blocks. If we know the price, we can easily determine the total cost of dry glue.

If the construction of the mortar from cement and sand is assumed for construction, and the scope of work will be the same, then you will need 2 cubic decimeters of glue. That is, 1 cubic meter of the solution is necessary for laying 5 cubic meters of blocks.

For the preparation of cube, the solution will be needed to 7 cement packs. The total cost will also increase due to the price of sand and rent a concrete mixer. Considering all this, it is not difficult to determine how much cement is needed for laying 1 cubic meter of gas silicate: 7/5 \u003d 1.4 bags.

By completing the correct cost counts, it is easy to ensure in the low value of the adhesive composition. The remaining priorities can only place you.

With the construction of modern buildings, it is important to ensure a reliable clutch of materials, which is achieved through the use of high-quality glue for gas-silicate blocks. Properly selected glue composition and accurate calculation of its consumption - the pledge of longevity of the erected buildings.

As the practice of recent years have shown, the use of dry construction mixtures during the majority of construction and repair work is much more profitable than the use of a conventional solution. So, with the help of glue for foam concrete, it is possible not only to perform the masonry significantly faster and better than before, but also save. After all, the consumption of glue on gas-silicate blocks is several times less than a conventional mortar solution.

The company "Basis" offers glue for gas-silicate blocks of its own production in a wide range. The use of modern equipment and advanced technologies allows us to produce world-class products that have passed all the necessary checks and has appropriate certificates.

At the same time, we propose to buy high-quality foam concrete glue, the price of which is noticeably below the average market.

Advantages of using glue for gas-silicate (aerated concrete) blocks

The use of special adhesive for foam concrete is almost always more profitable than the conventional cement-sand mixture, for the following reasons:

• glue has better adhesion, which helps to increase the strength of the structure;
• it's easy and convenient to work with him;
• foam concrete glue is characterized by the optimal setting time;
• it has high frost resistance and moisture resistance;
• consumption of glue for gas silicate blocks is several times less than cement mortar;
• glue is resistant to temperature fluctuations and in the same way well tolerate both high and low temperature;
• the level of thermal insulation of the building increases.

Counting of the flow of adhesive for aerated concrete blocks

Before starting work, it is desirable to calculate the number of necessary materials to assess the approximate cost of construction. Having a plan of the house, it is easy to determine how many blocks you need, since their geometric dimensions are well known. But how in this case calculate the flow of glue to gas-silicate blocks?

In fact, everything is quite simple here. The glue consumption is usually equal to 15-20 kg per cubic member cubic member, if the thickness of the adhesive layer is recommended 2 mm. Therefore, knowing the number of cubic meters of block required for construction, it is not difficult to calculate how much adhesion for foam concrete you need to purchase.

Gasilicate blocks are structural and insulating material with a cellular structure. They are obtained from a mixture of quartz sand and lime, in addition, with the addition of a small amount of cement. Therefore, glue for gas-silicate blocks is needed when the walls are erected, as well as any other structures that have a seam thickness from 2 to 10 mm. It is also suitable for aligning vertical or horizontal surfaces.

Such glue is an adhesive dry mixture, consists of cement, various additives and a fine filler. Additives have water-holding and plasticizing properties. With their help, the strength, frost resistance and moisture resistance are significantly increased. Quality data is very important, as often construction is conducted in adverse climatic conditions.

High-quality gas-silicate glue has excellent thermal insulation properties, it is incredibly durable, has high adhesion and is easily applied. It can be used to connect not only gas-silicate blocks, but other materials from cellular concrete.

Types and trademarks

It is divided into two main types - summer and winter.

Winter glue can be used at a temperature of +5 to -10 degrees for internal, as well as outdoor work. It consists of special antiorrosal additives. A snowflake is drawn on the packaging of such glue.

• Glue Zabudov is the most popular of frost-resistant mixtures. In addition to their excellent technical characteristics, it is perfectly applied to any surface and it is very easy to use it. It is approximately 115 rubles for 25 kg.
• Prestige and bonolite. The second one else is absolutely not toxic and environmentally friendly. The price of glue for blocks of gas silicate brands Prestige is about 140 rubles per 25 kg. Bonolite - 220 rubles.

The most common summer mixture is the Glue of the ACS brand. It can be used at a temperature of +10 to +25 degrees for masonry walls and various partitions. It is economical, convenient and has excellent water repellent properties. Price from 185 rubles for 25 kg.

Method of preparation and application

In order to properly prepare glue, it will take durable dishes, perfectly suitable a bucket of plastic. It is necessary to pour clean water, and then add a dry mixture. It is necessary to perform actions in this order, and not vice versa, it is also impossible to pour the whole mixture at once, it should be done gradually. Water needs to be constantly mixed, the drill with a special nozzle will help in this well - a mixer.

Consumption of glue is approximately 1 kg at 0.20 l of water. But the consumption of the finished solution is 1 mq. It is about 10 kg. It should not immediately breed too much a mixture, since after 80 minutes it solidins and becomes unsuitable for use. Working with the solution is carried out at any time of the year, but it is worth considering that the temperature should be not lower than -15 degrees. It should be noted that this instruction is not universal, a method for cooking and use is described in detail on packages of various grades.

For laying gas silicate products, you will need tools such as a smooth grater or celma, and a spatula for alignment.

The glue used for the gas silicate by its consistency should resemble sour cream. It is applied with the help of a trowel, carriage or a special bucket having a curved edge. After he is applied, it is immediately far from the spatula. After laying the first layer, the block surface must be fired by the plane. After 10 minutes, the glue is grabbed, but completely dries only after 72 hours.

Why is the glue better solution?

First faced with construction work, many land owners do not understand why builders choose glue for laying gas-silicate blocks instead of solution?

When using the solution, you may encounter the following problems:

• caps may appear between blocks;
• moisture will penetrate deep into the wall, in the future the wall will turn mold and fungus;
• after complete drying, the layer disappears between the plates, the strength of the structure is significantly reduced.

Advantages of glue

• applied very thin layers and is economically spent;
• contains special components, thanks to which the blocks are quickly seized;
• withstands any temperature differences;
• contains high-quality water repellent substances that do not allow moisture to penetrate inside the walls.

Gasilicate blocks are very popular with builders material. In operational characteristics, they differ simply wonderful. The walls of them are laid out with the help of a cement mortar, but using special glue. Of course, the box will be reliable only subject to the use of a high-quality bonding composition. What to choose glue for gas-silicate blocks, and let's talk further.

What properties should be a masonry mixture

First of all, glue for must have such properties as:

moisture resistance;

frost resistance;

high degree of plasticity;

good adhesiveness.

In order to perform the masonry, it was convenient, this type of glue should also not be captured too quickly. In this case, the wizard can correct the position of the already laid block if necessary. It is believed that the glue for gas-silicate blocks should not at least within 10-15 minutes. However, of course, and too long the grapped composition cannot be considered quality. The optimal time of frost is considered 3-4 hours.

Experts advise you to acquire glue and gas-silicate blocks included. In this case, the composition will be as suitable as possible. However, it often happens that manufacturers of gas-silicate blocks unreasonably overestimate the cost of glue. Therefore, many country owners who have decided to build houses from foamed concrete, prefer to acquire the fastening composition all the same separately. When buying such a mixture, you should first of all pay attention to the manufacturer's brand. This greatly increases the chances of acquiring quality composition with good operational and performance.

Popular manufacturers

If you wondered how to choose glue for gas-silicate blocks, you should think about buying the material of the following brands:

"Prestige".

"Unis Tea Unibok".

"Win-160".

"Bonolith".

"Obudova."

All of these compositions are characterized by environmental friendliness and high degree of plasticity. It is about them that the network has the best reviews.

Glues brand "Prestige"

The main advantage of the compositions of this brand is rapid preparation. The prestige glue can be used for styling not only blocks, but also cellular plates. There is a means of this brand inexpensive. For a bag kg will have to give about 140 rubles.

The composition of "Unix Temple"

This is perhaps the most popular glue for gas-silicate blocks to date. "What to choose the best composition?" - There are usually such a question from specialists. This mixture is simply a lot of advantages:

excellent thermal insulation indicators, as close as possible to the characteristics of the foam concrete materials themselves;

moisture resistance and frost resistance;

ease of use;

environmental safety.

There is a glue of this variety about 200 rubles per bag.

Aeroc Mixtures

The main advantages of this manufacturer include a high degree of strength. Most often it is used to perform thin-walled masonry. The advantages of this option are also considered frost resistance, moisture resistance and vapor permeability. The thickness of the seams in the masonry when using this glue can be 1-3 mm, which completely eliminates the occurrence of cold bridges. The bag of such glue costs about 250 rubles. On operational characteristics, this is perhaps the best glue for gas-silicate blocks at the moment.

Composition "Bonolith"

The main advantage of this glue is its environmental friendliness. No harmful impurities in its composition are absolutely absent. Its operating characteristics are also just wonderful. And it is a little cheaper than the adhesives of most other popular manufacturers - about 180 rubles per bag.

Zabudov means

For this glue, such advantages are characterized as easy to use and ease of application. Glue "Obudova" - the cheapest variant of the mixture of all intended for laying gas-silicate blocks. Those who want to choose the glue for gas-silicate blocks of good quality and at the same time save, it is worth thinking about the acquisition of this particular version. A bag of 25 kg of composition of this manufacturer is only 120 rubles.

The best glue for use in winter

Next, let's see what to choose glue for gas-silicate blocks if the masonry walls will be carried out in the winter. For the construction of houses from foam concrete during the cold season, almost all options described above can be applied. However, when choosing the most suitable composition in the store should be asked the option with special additives (winter). There are such compositions are a bit more expensive than summer.

A very popular tool intended for winter is, for example, a special kind of "Bonolith". Also, winter glue for the Golosilicate KSZ gas glue is often used in the cold season of the year. Pretty popular builders are also intended for masonry in cold weather adhesives:

How to cook glue

So, what glue for gas-silicate blocks to buy - with this we figured out. Next, let's see how to make the selected composition correctly. When mixing adhesives intended for fastening gas-silicate blocks in the masonry, such recommendations should be followed in obligatory:

A dry mix must be added to water, and not vice versa.

The kneading should be carried out with a special nozzle. In this case, the glue will be as homogeneous as possible, which means high quality.

After the first knead, the composition should be kept for 5 minutes.

Use the finished glue should be maximum for 2 hours.

When cooking glue, it is important to comply with the proportion specified in the instructions. Too much water content in the mixture significantly worsens its characteristics. In the process of manufacturing work, the finished glue should be intermitted periodically to maintain concentration. When preparing a solution, use a powerful drill. Water can be taken any.

How to check the quality of glue

To find out how good the composition offers the company or another purchase company, of course, quite difficult. However, determine which mixture is best suited for masonry, you can still. To do this, just buy a little bit of each of the adhesives. Next, they should be diluted according to the instructions in the same tanks. After the adhesive will dry out, the resulting solid material needs to weigh. The easiest glue can be considered the best. The smaller the weight of the material, the smaller he has the degree of thermal conductivity.

If desired, you can also check the strength of the composition and its adhesive qualities. To do this, you just need to glue two blocks, wait a while and sharply throw them on the ground. If they disperse on the seam, it means you should look for another glue.

Well, now you know what to choose glue for gas-silicate blocks is best in one way or another. When buying, first of all, you should pay attention to the brand of the manufacturer. If the masonry will be carried out in the cold season, you should also search for the packaging mark "Winter".