Bath, like every construction in the country area, needs constant care, without which it will quickly collapse. Lower the lower crowns and the floor can be filled with winter and water pipes in winter, fungus and ancient vertoon appear. Therefore, it will be possible to repair the baths with your own hands.

What problems may occur during the operation of a wooden sauna

All problems are directly related to the materials that are used to build it.

How to get rid of the resin that is distinguished from the tree

Wood for the bath should be easy to process and caring, moisture-proof, not inclined to cracking that does not emit resin. But for walls, doors and furniture (in rare cases) in a Russian steam room, where the temperature is lower than in the sauna, coniferous rocks are suitable. The log house made of a pine and fir-fir-cylindered log will be separated by resin at a constant effect.

The only way to get rid of it is to methodically consider the spatula with each bathing bath. Then after a few months, the resin will become less, and after the year of operation, it will no longer stand out.

How to wash ordinary dirt

After some time, the bathroom furniture, head restraints, the walls of the walls and the ceiling will darken, it will become porous, the dried dirt will appear - the products separated by man (dead cells, sweat, fat), traces of the bath perfumery and essential oils will appear. It also applies to the outer walls of the bath, only there is the cause of atmospheric phenomena: rain, snow, winds carrying dirt and dust.

In rustic baths earlier, the inner walls regularly scraped with a knife, removing the upper, dirty layer. But this is a very labor-intensive occupation that does not give a full result. The outer walls of the bath before did not clean at all.

Now the bathrooms after each use must be thoroughly wash with the help of special modern detergents.

But this is not all suitable for this, because some of them will not wash off, and they can give undesirable evaporation. There is a large assortment of detergents for baths.

Table: Means that will help clean the bath from dirt

How to clean the walls and ceiling from soot and soot

With many years of work of the furnace on the walls, the ceiling and the furniture pair sits down the black bold soot. This is fine graphite.

It is very difficult to delete it. Therefore, as a preventive tool, you must regularly pay attention to the work of your oven.

But if for some reason you cannot affect the deposition of the soot on the walls, it is necessary to regularly delete it. It is impossible to wash off the raid. First, you need a dry cleaning of a vacuum cleaner so that with moisture soot and the soot particles do not penetrate deep into the tree. Yes, and wash off with a solution of a conventional cleaning agent such a tax to the end is impossible, so you need to apply special chemical compositions. For example, the water washout of the soot and soot of Mazbit + based on alkaline components (it is called "for cleaning the premises from the effects of fire"). But it is necessary to use it with caution, besides very carefully flush.

How to handle walls and shelves Parilov from fungus and mold

If you wrap up when buying a contaminated board or log, then fungus and mold while in conditions of constant dampness later can spread to all parts of the built bath. A mucise appears on the surface, it is extremely difficult to derive it.

There are other reasons for the appearance of this problem:

• incorrect warming of a bath, resulting in condensate (from the ceiling and walls begins to drip);
• poor-quality wipelasaw of logs and foundation;
• poor ventilation steam and washer;
• regular insufficient drying of the room after operation.

Conditions that are created in a wet and hot steam room are ideal for the development of mold.

Black fungus is dangerous for human health. It provokes the development of tumors, allergies, can stimulate headache and rhinitis. Some of its species cause even bronchial asthma, generalized mycosis, pneumonia and myocarditis. It is impossible to just shock the amazed plot, it needs to be treated.

If you have problems with thermal insulation, there are drafts, then in such a bath there may be a woody mold mushroom.

If the mushrooms and mold do not remove all kinds completely, they will spread and simply destroy the bath. There are simple solutions to this problem:

Examples of anti-grab compositions of industrial production - Biotol, Dufa, Metas Bio, Ceresit, Neomid-Bio, Dali, Prosept 50.

When you are sure that you completely cleaned your bath from the fungus, dry it. And henceforth carefully follow its condition and appearance.

What to do to not appear black and rotting surfaces inside the sauna

Rotiation is a serious lack of wood. This destruction of cellulose when exposed to microorganisms that appear and multiply with high humidity. Temperature exacerbates the process. In the bath, rotting is most susceptible to the floor, withstanding water flows. The only way to solve the problem is to remove damaged areas of wood and replace them.

Bathroom Care Rules

Most of these problems can be avoided.

Why resin is allocated

Pine and spruce lumber must be perfect quality, without a single bitch, because mostly they are exactly the gate for the resin secreted.

The material must be preloaded and dried and dried, then the extraction of the resin will be reduced to a minimum.

How to prevent the appearance of fungus and rot

You need to carefully examine all the sawn timber you acquire. Amazed by fungus or rotten tree is immediately visible. If you notice copies with black or blue, it will be advisable to refer to another supplier. The likelihood is that the entire party is amazed, even if the fungus is noticeable not on all boards and bricnos.

It is better to buy a forest conceded in winter. Frost will not give the fungus in the wood. And necessarily before use and after the assembly, wooden elements need to be treated with antifungal impregnation.

Apply impregnation

This tool can save from many problems associated with the operation of the bath. For a modern busy person who does not want to use impregnation, there are only two ways to avoid the appearance of dirt:

• it is rare to use the bath or let it in it a small number of people (and it is good to dry it every time);
• every two or three years fully change furniture, cladding on the ceiling and walls (but this method is not suitable for everyone).

The first thing to be done still at the construction stage is to use high-quality impregnation for outdoor and internal surfaces. It is able to protect the tree from atmospheric precipitation, temperature drops, heating and high humidity without harm to humans, and at the same time protect the bath from the vertices, fungus and rot.

The fans of a healthy lifestyle assure that the wooden surfaces inside the bath does not only need to be processed, but also harmful. They believe that impregnation and paint and varnish coatings during heating give a sharp chemical smell and distinguish harmful volatile substances. This is true, if you use ordinary tools that are not intended for use in the bath. But if you leave the tree at an initial form, it cracks, and the fungus multiplies in the slots and micropores.

Those impregnating means, which are suitable for the ceiling, can not always be used to handle furniture. And they are very different means for outdoor cutting.

Domestic ("Sezheng", "Neomid", "Belinka", "Aquololor", "Empils", "Rogned") and foreign (Dulux, Tikkurila, Nobel, Belinka, Teknos) producers of varnishes and paints produce many means for internal and external impregnations.

External impregnation of bar

Funds for external impregnation are divided into industrial and private use. The first (pyropotic, strong antiseptic, insecticidal) wood is processed in the preparation of the forest to construction.

Be sure to need to handle it again after the construction of a chub, while the tree has not been exposed to atmospheric precipitation, not contaminated.

Inner impregnation

The means for internal impregnation are two types:

• for the surfaces to which we do not touch the body (for example, the ceiling);
• for the surfaces with which the human body contacts.

The latest requirements are much higher, especially to coatings for bathing furniture, which should not form the burning lacquer film. Sex impregnation should not slide, and is obliged to withstand regular wet cleaning.

For bathing furniture, agents with water-repellent natural substances of the type of paraffin, wax, butter, perfectly protecting the surface, which are harmless to humans are used.

Specificity of the application of protective compositions:

1. The first applying is made immediately after the manufacture of furniture on the dry and clean surface or before construction.
2. The remedy needs to be evenly distributed with a sponge, soft cloth or brush. Because of the thick consistency, the paintopult does not suit.
3. After drying the first layer, those places that will be subject to maximum load, such as seats, headrests, walls in the regiment region, need to be processed again.
4. Then the bath is soapped. When heated, the excess impregnation must be released, not absorbed due to the saturation of the tree. It is simply wiped with rags.

How to warm the bath in order not to appear condensate

With a properly designed and built bath, good capital doors and windows there is no need for additional insulation. But often such problems still make themselves known when operating. Several troubles may happen:

• draft and insufficient pairing temperature;
• cold floor;
• frosting of entrance doors;
• freezing of plum and pipes.

Draft and insufficient pairing temperature

Theoretically, during the construction of a church, you had to put it from punck between logs, and then carefully cross the grooves.

The bathroom device also needed to be done by all the rules, with insulation with clay.

But if it was done with a violation of technology, the bath scare from time to time, and the gaps were formed, then you need to carefully view the walls and doors outside and from the inside, especially carefully checking the corners. Surely you will find the places somewhere, from where it is warm. Then they can be processed once again outside and inside, pushing the jute tape into the gap and cover it with a similar cord.

If you failed to find such places, you will have to agree that the thermal insulation properties of the walls, the ceiling, the floor and the doors are not enough, and you need to warm the bath completely.

Wall insulation may be external and internal. In the first case, the bath is silent:

• vaporizolation material, for example, foam;
• insulation (good in that quality long-fiber mineral wool, her sheets are put on the brass, or insulating mats of Penoen);
• waterproofing material (rubberoid);
• clapboard, siding or block mobile.

Foam, made of foamed polyethylene, resistant to rotting, and is environmentally safe. Parosolation protects the insulation from the formation of condensate in it. Waterproofing prevents wetting outside.

Internal insulation is made on the same principle, only the skin must necessarily be made of natural wood of the type of parhed pine or birch.

The ceiling must also be inspired.

Cold floor

The freezing floor is necessarily insulating. It will be necessary to abandon the idea of \u200b\u200ba direct drain device. In this case, it is better to make the only plums.

What to do if the entrance door begins to freeze

If the door is frightened in winter, it means it is not insulating enough. There are two solutions to the problem:

• replace the door;
• warm it.

The second way is most often used. If you have a frame door, you need to disassemble, put mineral wool and re-assemble. If it is made of a headboard, it is necessary to put a sandwich from the wool and plywood on the outer side.

Freezing of drain and water supply pipes

The drain system is one of the important baths of the bath. It is necessary to do it immediately after the foundation device, before the construction of a log, simultaneously with the insulation of the sample. In the old baths, the drain went straight through the boarding floor to the ground, so the building was put on a natural slope.

Now such a drain is banned, but this idea is often used in steam room, and in the washing. The stock is organized through the entire floor or assembled at one point where the lattice-lattice is installed.

In no case cannot be connected to a common septic, that it will simply choose because of the volleary baths of discharges. You need to dig a separate drain pit.

And then problems may arise. The main cause of winter fire freezing is the wrong laying of the drain pipe. If it has a small tilt or lies wavely, the problems will necessarily arise. The tilt should be at least 2 cm on 1 m pipe, otherwise the water will be stamped. With wave-like laying in the lower bends, a liquid remains, which freezes, and the chain reaction occurs. In addition, if the slope is small, it may happen to the usual blockage, which is why the water is stirred and freezes. Therefore, pipes are preferably laying below the duration of the fruit of the soil.

But even when these conditions are met, the length of the discharge pipe should not be more than 5 m without insulation and 15 m with insulation. Lode in volume by 10% more water, and therefore can break the pipes.

If trouble happened, and the pipes were frozen, you need to immediately take steps to defrost. For this:

As soon as the pipe has frozen, and the fluid starts the movement, you need to immediately, not turning off the water, spread and insulate the pipe with an escape, mineral wool, foam "shell".

How to replace the bottom crowns do it yourself

The lower crowns are the weakest place of the bath. Of course, you need to make a maximum of construction to prevent their rot.

Preventive measures against the rotten crown

Prevent rotting is much easier than changing the lower crowns. Therefore, it is worth remembering the preventive measures:

1. All types of foundations, except for currency, need waterproofing. Usually used for this runneroid or bitumen.
2. Necking thin rails on top of the waterproofing layer is needed to prevent the moisture seepage to the log cabin.
3. It is recommended to put the lower crowns from the "Smalca". This tree is saturated with a resin, because it cuts down specifically at the moment of deployment. Such material is resistant to rotting, and under the influence of moisture.
4. For the construction of the walls, it is recommended to choose a tree firing in winter.
5. It is possible to launch a more durable and resistant to rotting a tree, for example, larch or cedar.
6. And it is necessary to carry out multiple treatment with impregnation with the maximum number of protective properties.

Step-by-step instructions for replacing the lower crowns of the Russian bath

If the trouble happened, and the lower crowns fired, they can be replaced. Depending on the degree of damage, a partial or complete replacement will be required.

How to renovate the lower crown

If the lower crowns are not completely damaged, then you can remove and change only some of them, following the plan:

How to completely change big brica

If logs rotted in several places, it is recommended to carry out its complete replacement. For this, careful preparatory work is needed, since the entire log house will shift in this process:

1. It is necessary to remove window frames and doors, remove the souls. Release furniture. Disassemble the floor, but only if the lags are embedded in those birings that need to be removed.
2. Disassemble the design of the chimney so that space remains between it and the roof. Otherwise, the structures of the furnace design can not be avoided, and the roof may also be damaged.
3. Log's log cabin fix four screeds from all sides on each wall.

It is necessary to determine which two of the four logs of a rotten crown top. Under them and you need to put jacks. Replacement sequence:

What if the log house began to mow: step-by-step instruction repair

If your bath is made of clean, the unwinted cut visually looks like a curved, or if, when it seems to be straight walls, their trim inside or from the outside (at the same time it can appear), this means that the soil sewn occurred on one of the corners of the foundation or the deformation of the church itself . For alignment, you need to use jacks.

The process consists of several steps:

1. The covering is completely removed, the thermal insulation can not be touched, but you can only reinforce the log cabin.
2. Doors, windows, souls are removed, the entire furniture is pulled out.
3. Roofing around the chimney and the floor near the furnace.
4. Jacks are summed up, first under the sensory part. Raising each of them little by little, the bath is lying in a plunder or a hydrorer. You can then make the strapping with a metal chaserler to create an additional rigidity.
5. Then the bath is rebuilt again, all disassembled nodes are restored.

Video: Replacing the crown of a bath

You learned much of what you will need for the long and smooth operation of a wooden bath on the household plot.

Mold in the baths - often arising problem. The reasons for its appearance lie in favorable conditions for development. The mold fungus loves moisture, warmth and darkness, and the bath is perfectly suitable for all three "requirements".

The main problem lies in the consequences to which the development of fungus can lead. No need to forget that the fungus is a living organism and it feeds it precisely the wood, from which the bath is often made. The result of mold metabolism are substances that adversely affect the respiratory and circulatory system of the person.

Causes of mold appearance in the bath

Before changing the problem, you need to understand why it occurs. Consider the reasons that can lead to the appearance of mold:

1. Bathrooms (shower, steam room), except for the pre-banker and recreation room, usually do not have windows, that is, the lighting is here only artificial. The absence of sunlight is one of the causes of the appearance and growth of mold.
2. In order for the steamer well to keep warm, it should be maximally sealed. To achieve this goal, construction often forget about the correct ventilation (especially if the bath is built on its own).
3. Permanent high humidity is one of the main conditions for the growth and reproduction of the colonies of mold mushrooms.
4. If the bath is built of wood, and / or for its interior decoration is used, it significantly increases the likelihood of mold. Even if the wooden surface was covered with special compositions, it is not guaranteed protection.
5. Incorrectly performed insulation construction, insulation only from the inside. If the thermal insulation and waterproofing were made with errors, the dew point can shift, causing the accumulation of condensate inside.

In addition to this room, Parims usually have a small volume. That is, elevated humidity (in the absence of ventilation) it arises quickly, and is supported for a long time.

Where exactly most often the fungus appears in the bath?

The bath usually consists of several rooms. Consider what kind of rooms the bath fungus appears most often:

1. In the steam room, since it often does not have a window and ventilation. The room itself is small, the temperature in it is high, the humidity is almost 100 percent.
2. In the pre-tribades, usually damp and warmth, because it is here that visitors are resting after the steam room. This is the ideal for the growth and reproduction of the colonies of mold mushrooms.
3. In the shower, around the shower pallet (if any), especially if it is small, and does not have the windows.
4. On the wall, in the place where brooms hang (if you leave wet brooms hanging in a non-ventilated room).
5. In the sauna, unlike the Russian bath, the mold arises much less often, because there is dry air and a higher temperature that can reach 130 degrees.

Places and materials that are amazed most often:

1. First of all, it is the places where the most wettened: the angles of the room, as they are worse than all are ventilated. The ceiling also suffers: the ceiling: warm air rises up, and can be condensed on the inner surface, gathering drops. If you do not remove the flare on time, it will appear on the wall, and on the floor.
2. Moldably mold feels in a wooden bath. She loves to live on the boards and on the clapboard. However, an absolutely all building materials (brick, concrete, etc.) can affect the fungus.

What is it dangerous?

Having come to the bath, in which there is a mold, a person, instead of cleansing the body, receives a dose of harmful disputes and toxic discharges.

Second problem - mold flip is very harmful to the structure. He causes rot on the tree and speeds up the destruction of its structure. Faster and finishing materials are fastened, and the construction itself.

Of course, this does not mean that for the year the building will fall apart, but the appearance will deteriorate very quickly.

How to get rid of fungus in a bath?

To destroy the mold and prevent its re-appearance on the logs, one only does not help with special processing. This can temporarily remove the flare, but if the microclimate of the room does not change - the fungus will appear again.

It is necessary to drastically change the conditions for the use of premises and care for them:

1. It is impossible to allow constant dampness and humidity in the room.
2. It is necessary to maximize the circulation of air. It is advisable to use forced ventilation (inlet installations, exhaust) - it will allow you to quickly update the air.
3. Ideally - you need to provide access to sunlight into the room. The item is not obligatory, much more important to ensure ventilation and prevent dampness. However, if there are at least small windows in the bath (for light contact) - it will be useful.

You need to fight fungus at once, as soon as you noticed that a black or white mold appeared on the surfaces.

Especially carefully, it is necessary to inspect all the inner surfaces of the bath after the winter, because in the winter and spring period due to the temperature difference, condensate is formed on many surfaces of the construction. Remember: the earlier the struggle started, the easier it will be forever to get rid of the problem.

Now about what to do if you have noticed a mold flare in your bath:

1. If in the bath damp, bring all the fans and heaters to it to warm up, dry and ensure the maximum circulation of air masses. If during the construction, the ventilation system was thought out (there is at least a trimming valve in the wall through which the air will flow), the task is greatly simplified.
2. While the room is ventilated and sucked, carefully examine all the inner surfaces. Especially carefully examine the angles of the floor and the ceiling, the joints (between the boards), the sections around the windows and doors, the sections that are covered with furniture, sites that the sunlight does not enter.
3. If the damage to the fungus is barely noticeable, you can immediately process the surface with special safety. If the foci is large, and the flight touches, it should be considered with a spatula and metal brushes. If the mold was entered into the finishing materials, it is best to dismantle them: even after processing, the disputes can remain inside.
4. Now choose the tool (from the list below) and apply it to the stripped areas. You need to handle not only the affected zone - capture at least 30-50 centimeters around it.
5. We give the tool to work (how much time it is necessary - it depends on exactly what you did processing).
6. Then we consider it once again a flare with a metal brush, well wash the plots and again we succeed in the room.

With a strong damage to the action from paragraphs 4 and 5, it is necessary to re-hold.

Elimination and prevention of mold in a wooden bath (video)

What to treat mold in the bath: list of funds

Take the fungus - the task is though both time-consuming, but perfect. This can help both folk and modern methods.

Effective preparations for the destruction of colonies of mold melmies are:

• bleaching powder;
• sulfur;

If you prefer more modern funds, or if the lesion area is very big - go to the economic store. There you can choose a surface or deep exposure tool, designed specifically to remove mold.

List of funds that can be applied:

• Seneja;
• Viotol;
• Dufa (based - chlorine);
• Ceresit;
• METAS-BIO;
• Neomid -Bio;
• ALFA-Fongifluid;
• Olymp-Stop.

You can choose other special needs - above are not all names.

Eliminate the reasons for the appearance of mold in the bath: Prevention

The fight against fungus lies not only in the one-time destruction of the focus of infection. Prevention of fungus - no less important stage.

To eliminate the causes of mold appearance, it is necessary:

1. Provide full ventilation in the bath. To do this, you need to install or

The mold often appears on the walls, the floor and ceiling of the wooden bath - dampness, lack of high-quality ventilation, labeling and periodic heights create conditions favorable for its development. The fungus should be attached immediately after it is detected. Sendance can lead to partial or complete destruction of wood, and as a result, the major overhaul of the structure may be needed.

• Tamara Globetoba break out of lack of money once and for all, in 2018 Take a rule to carry with me ...

1 Preparation for work

In order for the tool to work, it is necessary to properly prepare the room and surfaces for processing. For this you need:

1. 1. Carefully ventilate a bath or sauna.
2. 2. dry wooden surfaces (floor, ceiling, walls, shops, doors). If in the summer it is enough to leave the door to the building open, then in the cold season of the year, when the air is not yet heated, it is necessary to use an electric heater or flood the oven.
3. 3. Delete all traces of fungus from the surfaces. Too much damaged elements replace new ones.

Black mold in the house: Hazard for health and effective ways of struggle

2 Mechanical cleaning

If you find the mold managed in the early stages, when she had not yet had time to penetrate the injection of the material, you can do a simple stripping. In order to remove surface traces of fungus, elaborate paper, spatula or metal brush. It is most convenient to work with a grinding machine or a drill with a special-brushed-brushed.

Order of work:

1. 1. First, all surfaces carefully examine, revealing the plots affected by fungus.
2. 2. The found problem areas of the walls are watered with water. Such a measure will help prevent the spread of the dispute of mold.
3. 3. Any of the above tools thoroughly cleales the found areas found carefully.

If the fungus penetrates deep into the wood, this method does not help. It will be necessary to replace the damaged element. In this case, the board or part of the log is cut and replaced with a new one. Mushroom-affected materials are recommended to burn so that the disputes of mold do not apply.

Wall processing from fungus and mold before cutting wallpaper

3 Folk remedies

To get rid of applicants formed after winter mold, use:

• chlorine lime;
• sulfur;
• copper sulphate;
• funds with chlorine content;
• hydrogen peroxide;
• ammonia;
• vinegar;
• soda;
• alcohol.

Means	Recipe	Mode of application
Bleaching powder	A small amount of substance is connected to water to get a weak solution	The liquid is wetted by a fungus surface, leave for 2-3 hours. Work in gloves and respirator, organizing in the room draft. After the specified time, it is pissing a brush with a rigid bristle, wash off with plenty of warm water, and then carefully dry
Sulfur	Calculation of the amount of sulfur based on the area of \u200b\u200bthe room: 25 g of substance for each cubic meter	Premises prepare: close all the ventilation holes, windows, doors in the bath. The sulfur is placed in a metal container, ignite. The burning substance highlights a sulfur gas that is destroyed for the fungus (it can also harm it, so work should be carried out in the respirator, and immediately after the ignition of the sulfur, get out of the room on fresh air). Leave for 9 hours so that the smoke destroyed all the colonies of mold. After this time, the container is put in the room with a negated lime - it neutralizes harmful evaporation
Copper Kuner	50 g of substances are dissolved in a liter of water, add to the capacity of 30 g of the table salt and 100 g of alumokalia alum	Well mixed liquid is applied on the surface with a sprayer, roller or brush. Conduct work by defending the respiratory authorities with a respirator, and hands - gloves
Chlorine bleach	Tool type "White" or other bleach connected with water in proportions 1: 1	Abundantly apply the resulting solution on the boards several times with a painting brush. Leave for a while, wash off with water
Hydrogen peroxide	Use 3% solution	Apply for a cotton disk, wipe the plots affected by fungus. After the processed areas are completely dried, wipe them with a wet clean cloth
Ammonia	Bred in half with water	Liquid is applied to moldy surfaces in several layers, leave for a while, wash off with water
Vinegar	9% solution is used undiluted	Apply with a sponge, brush or painting roller, abundantly wasting problem areas
Soda	Use powder in pure form	A small amount of soda pour into a problem area, a clutch with a wet sponge or cloth. You can also make a small amount of soda with vinegar, apply a resulting liquid on the surface with a fungus in several layers, wipe the boards with a rag after drying
Alcohol	Use undivided	Apply a roller into several layers. Leave to complete drying (for 3-4 hours), wash off warm water

Remove the fungus in the bath, if it penetrates deep into the structure of the tree, the folk remedies will not work. In this case, it is better to take advantage of special drugs.

How can I remove the fungus on the walls at home?

4 Chemical compounds

The finished means for removing mold acts effectively, but choose and use them should be carefully: most of them are very toxic. They penetrate into the boards and are not pulled off with water, and with the subsequent use of the bath (when the ceiling, walls and heat from hot air are heated) can be distinguished harmful substances. Therefore, only those means should be applied for bathing and saunas.

Chemical compounds can be divided into three types: water based, based on oils combined. Only aqueous solution is considered safe for use in the bath. The rest are highly toxic, and therefore it is impossible to apply them to process the internal surfaces of the premises.

Name of the composition	Purpose	Concentration	Mode of application
HOMEENPOISTO (HOMEENPOISTO)	Removes mold, blue on wooden surfaces	Bred by water in proportions 1: 3	The solution is applied to problem areas with a soft bristle, with large areas of lesions, a garden sprayer is used. In the second case, it is recommended to apply a remedy from the bottom up, from the floor to the ceiling. The processing duration depends on the depth of mold penetration - the stronger the damage, the longer the solution is kept. After flushed with a large amount of clean water
Fongifluid (Fongifluid)	Effective against mold of all types, fungus, lichens, moss	Applied undegrade	Works should be carried out at an air temperature not lower than 5 ° C. The liquid is applied with a roller or painting brush. They leave for 5-6 days, after which the surface is cleaned with a dry brush, washed with water under pressure and carefully dried. With serious lesions, re-processing will need
Sezheng Echo	Acts against mold, algae, moss and lichens	Apply undiluted. To remove small traces, fungus can be divorced in half with water	The fluid is applied along wood fibers using a brush with a synthetic pile. Drug consumption: 150 g per square meter. Leave for 2-3 hours. Washed with water. Repeated processing may be required.
Olympus Stop Mold	From rot, mold, lichen, moss, fungus	Use undivided	Apply a surface fungus based on 1 liter of liquid on 5 m² on visible traces. Leave until complete drying
Dali.	Fights with fungus, mkhami, lichen, all kinds of mold on any types of surfaces	Apply undivided	Consumption depends on the depth of the surfaces of the surfaces (from 50 to 250 ml per square meter). Apply a means with a brush or roller. Leave for 5 hours, after which they apply a second layer. Leave on the surface for 24-48 hours, after which the remnants of the means are brushed and washed with water boards
Neomid Bio.	Effective against mold, fungus, algae, moss, lichens	Do not dilute	The remedy is sold in a spray bottle. The problem areas are abundantly sprayed with a distance of 15 cm, leave for 1-2 hours. It is written to the remnants of a metal brush, the means is replaced. Do not wash off - it will protect the surfaces from re-formation fungus

All works should be performed using hand and respiratory protection tools (rubber or latex gloves and respirator). In the room there should be a flow of fresh air.

5 Preventive measures

After removal of mold, the surfaces should be protected from the re-appearance of it. For this you need:

1. 1. Organize high-quality ventilation in the bath. This will help reduce the level of humidity: dry air will prevent the formation of fungus.
2. 2. Treat all wooden surfaces with a special antiseptic primer.
3. 3. Dry all towels, pelvis and containers for water heating after use.
4. 4. Heat the walls, ceiling and slopes so that they do not freeze.

It also needs to be remembered that the fungus intensively multiplies on polluted surfaces, and therefore, after each use of the room, we need to wash the floor, shops and other surfaces with the help of cleaning agents intended for the sauna and bath.

To combat fungus, only non-toxic means should be used, and after removal of mold maintained cleanliness and moderate humidity in the room - such measures will help protect the bath from re-formation fungus.

The microclimate, which is created in the bath (sauna, steam room), is a coincidence of favorable factors for the development and distribution of various mold strains. The reasons for the appearance of mold are an elevated level of humidity, high air temperature, low-quality building material, poor ventilation, lack of solar lighting. If the construction of a steam room is wooden, the disputes penetrate deep into the wood and get rid of it much more difficult in the case of untoulated measures taken to remove it. The jigsaw in the bath can provoke partial or complete destruction of wood, which means that the steam will be subjected to overhaul on the replacement of individual logs. .

Where mold appears most often in the bath

Mold mushrooms are well hiding and to discover them in time, you will have to work hard. The clear mold is manifested only when the colonies are already quite developed and spread to the walls, the ceiling, the floor of the bath.

If a unpleasant stead of dampness appeared in the sauna, then the presence of the hidden dispute of mold should be thought about. You can detect it in hidden hard-to-reach places:

• in the junctions of logs;
• in corners;
• on the edge of shower pallets;
• in plumbing;
• on bath shelves;
• in ventilation pipes.

As a rule, the fungus appears in places, which due to complex access often remain sufficiently cleaned and washed. Each mill and visits to the bath should end with careful cleaning in the room using various detergents, which contain anti-flap substances.

Sources of mold: Wet mats, towels, which, after disconnecting the heating of the bath, remain on the floor or shops. Screens in the inner rooms of the bath should be straightened so that moisture does not accumulate in the folds.

If the mold appeared in the bath, how to get rid of it? Effective funds whose action is aimed at combating fungus, abound. Some of them are the developments of the chemical industry, others are transmitted from generation to generations and constitute folk methods to combat the spread of various types of fungal colonies in the bathroom.

Test tools from mold in the bath

The presence of fungal dispute indoors not only gives an unpleasant smell of mold and spoils the appearance of wooden surfaces, but also negatively affects human health. Under the action of hot wet air, human skin pores are expanding, the body is cleaned from toxins. But at the same time, spores of mold mushrooms penetrate the revealed pores.

In the steam room, most often, the white house mold appears, but there are also cases of appearance and more dangerous species, for example, a black mold. If the dispute in the human body is high, the risk of developing various diseases:

• allergic reactions; (Read more Read "Allergy to Mold")
• pulmonary diseases;
• defeat and eye irritation;
• gTS diseases;
• benign and malignant neoplasms.

Due to the risk, the processing of the bath from fungus and mold should be in the first place. Otherwise, instead of use from visiting a bath, health will deteriorate significantly.

How to deal with fungus in a bath? Tested means of combating mold are both folk remedies and chemicals. The chemical industry has created many funds against fungal colonies:

• Fungicide;
• Snow;
• Hydroca;
• Atlas Mykos;
• Domasestos;
• Boramon;
• PS 50;
• Renogal.

Folk remedies for combating fungi and their disputes are much cheaper at a price and, as a rule, are present in every home:

• boric acid;
• ammonia;
• copper sulphate;
• bleaching powder;
• hydrogen peroxide;
• soda;
• white;
• resin;
• vinegar.

The choice of funds depends on the material that was used in the construction and finishing of the premises of the steam. So, it is better to use substances that, in effectively destroying the dispute, do not change the shade of wood. If you need to process tiles and seams between tiles, then the use of potent bleaching preparations is permissible - whiteness, hydrogen peroxide.

Elimination and prevention of mold in a wooden bath

• How to get rid of fungus on a tree in a bath? To clean the surfaces of the wooden bath room from fungal colonies, not only the choice of the means, but also the observance of a certain sequence of impact on the affected wood. First of all, it is necessary to clean the mold in the baths on the logs. Machining wood is carried out using emery paper of different fractions, iron brush or spatula. Before stripping, it is recommended to moisten a tree with water. This makes it possible to eliminate the possibility of spreading the dispute by air.
• How to bring the fungus in the bath? Depending on the depth of the destruction of the tree disputes, the stripping can take some time. After the complete removal of the fungal colony, it should be treated with the antiplamp wood. For a bath, built or finished with natural materials, it is recommended to use substances with not a sharp odor and with reagents that will not damage the structure of the wood.
• How to remove mold with lining? The process of removing the fungus with the clap is almost the same as when it is eliminated with logs. The lining is more often used as a decorative material. It can be treated with hydrogen peroxide and leave for a couple of hours. After the surface is driving, it is necessary to wash off with a solution of pure water. Ventilation in the bath should be well thought out so that there is no mold and its dispute in the air. The ventilation holes must be carefully processed, since they are not only disrupted through them, but they can accumulate. And when ideal conditions are created in the air, penetrate back to the room and begin to spread.
• How to remove mold in the bath? To prevent the appearance of spots of fungal colonies, the purity of the chimney is playing an important role with a fire heating. It is necessary to regularly clean the chimney from the soot, since its clusters violate air circulation. Conducting the removal of colonies of mold from walls, floors, shops in the sauna should observe some precautions for protecting the hands and respiratory organs. Before using the tool, you need to wear rubber gloves and use the respirator or gauze bandage. For applying substances used washcloths or sprayers. Using the sprayer, the cleaning agent can be applied to hard-to-reach surfaces - slots, angles and ventilation and waste holes.

Photo from Stroisovet.com

From Handra and from diseases there is nothing better than Russian steam room. After her visit you feel renewed and fresh, as if it was born again. At such a moment I do not want something overshadowed rest. But, unfortunately, places with high humidity and high temperature - for the fungus.

If you do not fight this annoying trouble, then soon your favorite hygienic procedure will stop bringing joy, and the benches in the steam room will turn into packeries. But there is a way out, in this article we will tell how to get rid of the fungus in the bath.

Photos from the site

Know the enemy in the face: what is fungus in the bath

As it often does not even have a buyer with experience, it is not always possible to recognize these malicious bacteria and neutralize, therefore, the distribution foci is quite large.

So what is the fungus in the bath? After all, if you do not understand the nature of the nonsense, it will appear again and again, because the weapon will be chosen incorrectly.

The fungus on the logs in the bath can look like a whitish or greenish gun, it turns into a mucus due to evaporation. This is an ordinary mold that breeds disputes, so it is not even recommended to enter such a room without a respiratory mask, not to mention that it is strictly forbidden to use the steam room for its intended purpose.

Photos from the site

What is dangerous for the appearance of such a neighbor? It is not necessary to dismissively relate even to a small raid, the usual powder will not escape it. It is especially important to know than to handle the bath from the inside of the fungus if there are small children from the amateurs. This problem harms not only wood, destroying it, but also to the health of visitors.

It may threaten as follows:

• skin itching, inflammatory reactions, allergies;
• diarrhea, poisoning;
• candidiasis of the intestine.

Now you have no doubt that you need to get rid of bacteria immediately.

Uninvited guest: the causes of mold

Colonies The fungus is lipped on the floor, walls, benches - on all wooden surfaces. If you lose the moment, the fight against them can be long and tedious.

Photos from the site

This seelhead feels folly in warm wet buildings and spreads at the speed of light. The main reason for the appearance of fungus is insufficient ventilation of the room. But this is far from the only thing that can ensure the appearance of mold.

Other negative factors are:

• malfunction of plumbing devices (pipe leaks);
• bad cleaning after bath procedures;
• forgotten raw things inside dry closed steam room.

Photos from the site

Unequal fight: fungus in a bath, how to get rid of

After several unsuccessful attempts, people continue to break their heads over how to eliminate the fungus in the bath. Indeed, often the condition is close to a panic: after all, do not burn the same bath with Napalm to join the mold?

Hurry up to calm you, Currently, the chemical industry offers a lot of effective funds, but if you are supporters of antiseptics of close natural, then the tips of the experienced tips will be helped.

Verified tools: how to bring the fungus in the bath

Bacteria with disputes have properties not only to grow stirre, but also deep into, penetrating between the logs. The opposition becomes more complicated by the fact that the mold happens immediately not visible on the surface, so it takes not only infected foci to handle, but all the space.

It is worth taken into account that the means from fungus on a tree in a bath of both chemical origin and natural can affect not only malicious pests, but also on the person himself.

Remember, you should not neglect the following precautionary measures:

• Before processing, put on the clothes made of dense fabric, gloves, headdress, glasses and a dressing or a mask that protects the respiratory tract. Such equipment is never excess.
• After the sanitary procedures conducted, do not leave the door locked. Give a well ventilated by the room.
• When the remedy works and it will not be necessary, thoroughly wash all surfaces with plenty of water.

We turn directly to how to remove the fungus in the bath from the tree.

The most common weapon can be called a special primer against mold. When purchasing it, consult the seller and make sure that the substance is suitable for your purposes. After all, the mold can stick to the cafél, and to the metal. You need a composition safe for wood. Carefully read the instructions on the turnover, where it will be indicated: the amount of primer needed to process surfaces, as well as the duration of exposure.

Photos from the site

My bath from fungus: disinfection

Since the tree is an organic, natural material, it is actively in contact with microorganisms. Mold can penetrate the upper layers of the boards. Therefore, the best solution, how to derive the fungus in the bath on the boards, will, of course, the mechanical method. It is a grinding when the surface is polished.

You can also consider the growths automatically rotating brush with rough bristles. Before starting to scrape the fungus, it is necessary to richly moisten the affected area with water so that there is no malicious dust. If the situation is so heavy that it is necessary that such a liquidation method is required, it is better to turn to the master, which, if necessary, can cut a spoiled part and replace it.

But in the case of timely detection, chemical compositions are quite effective. It is important to note that in most cases absorbed into the walls and later with increasing air temperature can throw toxic evaporation. Therefore, it is necessary to choose this composition extremely carefully.

Currently, there are three categories of manufacturing substances:

• antiseptics based on oils, they are considered organic;
• water-based means;
• combined antifungal formulations.

The fungus appeared in the bath, but do not know how to destroy it? Boldly choose water antiseptics. Of all those represented, they are considered the most safe, as it is easily weathered and do not penetrate the structure of the tree. Before use, again, you need to carefully read the instructions on the product labels.

Very important

Some methods are truly killed not only for mold, but also for a person. If you do not have experience, it is better not to experiment with such types of liquidation of fungus, where products are used for burning sulfur and other substances in their nature. Yes, sulfur gas can really remove the colony of bacteria, but for a person this experience can end to death.

Another economic, but more gentle method is the processing of surfaces by chlorine. This method of disinfection is widely applicable both in public places and in domestic conditions. After the procedure, careful ventilation is performed, and during sanitary cleaning all precautions are observed: the presence of mask, gloves and closed clothing - be sure.

Photos from the site

Prevent and neutralize: Methods and methods of prevention

If you are familiar with such a potential problem as a mold, but your steam room is only at the construction stage, you probably wondered how to process a new bath inside from fungus.

Apply preventive measures much better than to deal with the consequences.

Here are some tips to help avoid troubles:

• Best building material - logs cut off during frosts. At the same time, about the foundation for the future bath, too, you need to take care in winter, but the walls themselves need to be folded when warming up.
• In no case damaged details cannot be used, it is better to get rid of them.
• Think out a competent ventilation system. Production should be underground, under the attic and in the walls.

Currently, a lot of know-how appeared in the construction of such structures, and you will not be difficult to protect the logs from rotting, and the foundation is from wetting.

It is important to remember that all boards and wooden parts are better to treat versions in advance, desirable, water based. This will prevent the appearance of pathogenic fungal bacteria.

Photos from the site

As a conclusion

Thus, you learned about the large number of ways, how to bring the fungus in the bath on the walls. If you have to buy a finished building, inspect it for such unpleasant surprises. Mold is a nasty and arrogant neighbor, the fight against which is very tedious. Do not neglect the prevention measures and worry with pleasure.

Mold (fungus) in the bath is a real threat to people and their property. It not only becomes the cause of the destruction of the construction, but also affects human health. So, it can cause diathesis in a child, strong allergies, which can go to asthma, migraine, cardiovascular disorders. The fungus in the bath is a frequent phenomenon, because it loves moisture, and in this room there is almost always condensate - ideal conditions for breeding. So, if you encountered such a problem, emergency measures must be taken. In this article you can learn how to get rid of the fungus in the bath and prevent the reappearance of it.

Dampness - the reason for the appearance of mold number 1

In the baths, the humidity is always increased - this is a pattern, and nothing to do with it. If there is no additional heating in the construction, most often it is wooden baths, then you are in a high risk group. The fact is that heating allows you to dry air, walls, and the likelihood of the appearance of fungus is reduced. Heating is not - the bath makes it yourself, the walls remain longer than wet - it is good for mold.

The reason for the stagnation of moisture can be wounded in factors such as no ventilation or its incorrect equipment, blockage. In this case, the fungus first appears in places where the air movement is the weakest, and then fixing, without any problems spread over the wall, and the light drafts are no longer bothering it. If the case is in ventilation, then it is necessary to create it, reinstall, clean, install additional fans that will help drive air, dry the room. Then we will tell how to get rid of the fungus in the bath, and while we consider another reason for his appearance.

Insufficient cleanliness

Many bath owners suggest that this is the cleanest room, because there is always humid, and disseminate the ceiling and walls, believing that it is enough to clean the floors, shelves and accessories. The fungus loves dirt, and together with dampness, so generally perfect conditions.

If you have a good ventilation, even the heating is installed, and the mold still appeared, which means that not enough hygiene.

What to arma?

Before you get rid of the fungus in the bath, you need to think about your own security. Considering the mold from the surface, you spread its disputes in the air, and they can get into the lungs. Before starting the struggle, you should purchase the next protective inventory:

• the respirator will help protect the mucous membrane of the nose and the mildness of the ridge and the chemicals that you will withdraw the mold;
• rubber gloves will protect your skin and nails.

This is the necessary equipment, and without it in no case begin to fight the fungus.

Is it difficult to eliminate the fungus?

The disputes of mold are creatures very mobile and, only appearing, begin to spread all over the room. Treat only visible lesions is not enough, anywhere can still be black and white fungus in the bath. How to get rid of this pest? First of all, it is worth assessing the situation, find all the foci of the defeat, make out of the room all that is not attached, and begin the treatment of all walls, ceiling, regiments, floors. It is worth noting that the extended inventory must also be processed. Get rid of the fungus even in the first stage very hard, not to mention that the disputes could have time to penetrate into the boots for several centimeters, clogged into the gap. Where to begin?

First step to get rid of mold

To begin with, you will need to mechanically clear all visible places of defeat. Especially carefully inspect each centimeter, even the incomprehensible speck can be fungus, so do not miss it out of the view.

The first thing is not in a hurry, carefully, so as not to distribute disputes throughout the territory, the spatula remove the layers of mold, go through all the slits and the corners where the fungus was found. Mechanical cleaning is very important, it allows you to remove all surface lesions that protect deeper. After that, you can start a chemical attack.

Do not forget about ventilation

After machined cleaning, you need to go to ventilation. In most cases, it also has fungus, there may be a focus of infection. First, process the ventilating system with antibacterial agents, it may be ordinary alcohol. It dehydrates well, that is, dehydrates the surface, can push out moisture from the most narrow slots, in addition, destroys the spores of mold. Do not forget that this substance is flammable, therefore, the room after processing is thoroughly ventilated and proceed to the next step.

In the housekeeping store you will find special primers. They may simply protect the surface from the appearance of mold, and can and contribute to its destruction. Select a tool suitable for your wood, and process them with ventilation. Now you can process this primer and all other surfaces in the room. Next, consider how to get rid of the fungus in the bath in other ways. There are many of them, we offer the most efficient.

Sulphur dioxide

It sounds frightening, but there is nothing easier and more efficiently than bringing the fungus in the bath with sulfur. This procedure is very unpleasant, the substance smells badly, dangerously for all living things, so before applying this method, take care that all possible gaps are tightly closed. Shut up tightly ventilation, the pipe, if the bath is attached to the furnace, all small slots and holes through which the danger can penetrate out. Sulfurous gas is very dangerous, he will save one hundred percent from the fungus, but in no case you ourselves should not expose it.

If the floors are wooden, it is better to take a ceramic container if concrete, then it can be a metal dishes. Put several pieces of sulfur there, at the rate of the one hundred cubic meters of the room you need two hundred grams of substance. Fit the sulfur, it will highlight the gas, destructive for fungus. After she began to act, immediately leave the room and close the entrance door tightly. It is important to use the respirator during arson and with further actions.

At least six o'clock, and better in nine, take a box with a negared lime. Go to the bath, remove the residues of the sulfur, put the lime box on its place. It neutralizes the remains of sulfur gas, dries off the room, absorbing the extra moisture. The box should be in the bathhouse, after that the room is carried out as much. You can operate the bath immediately after it is ventilating.

How to remove the fungus in the bath with chlorine lime?

This is also a good option, but it is better not to use it for a wooden bath, since the chlorine lime is not too safe for wood.

After cleansing the walls from the mold mechanically, a specified substance is necessary to dilute in a small amount of water and this solution to go through all surfaces. There is one more option: take 25 milliliters of forty-percent formalin per liter of water, add chlorine lime and treat the floors, walls, ceiling, shelves.

How to get rid of fungus in a wooden bath?

Sulfuric gas and primer are ideal for wood, do not damage it, but there is another gentle method of getting rid of mold in the bath. It is necessary to take on one liter of water 22 grams of iron of iron, 44 grams of aluminum aluminum alum and 18 grams of the usual table salt. Fait roller into the solution, process all surfaces after mechanical cleaning from fungus.

You can also use the following recipe, but pre-warming up the mixture to seventy degrees. You will need one and a half tablespoons of vinegar (not acid), ringer of boric acid and kilogram of borax. Dissolve the components in a small amount of water.

Both recipes are effective, but still weak, they may not take the entire fungus from the first time, so they processing again in a month.

Prevention

Of course, to prevent the appearance of fungus in the bath is easier than getting rid of it. If you have ventilation, still do not forget about ventilation. They should be made not only after the operation of the bath, but then when you do not use her, because water can be stood, and then evaporate. Carrying are not less than once a week to six hours.

Conduct preventive treatment with iron vigor or other substances. Remember that after using chemicals, you need to air the bath, then rinse the walls to not harm your health. We hope that this publication on how to get rid of fungus in the bath will be able to help.

Reducing blood sugar by folk remedies quickly and efficiently
After training the muscles hurt what folk remedies

Evgeny Sedov

When the arms grow out of the right place, live more fun :)

Content

The owners of the bath are faced with this problem, which equipped the steam room, but the ventilation is insufficient. If you do not pay attention to mold in the bath, it can penetrate deep into the walls, which will make sure to get rid of it. Recipes and tips will be relevant to most people having their pairs.

How to get rid of fungus in a bath

The room in which the heating system does not work on a permanent basis is an ideal fungus formation medium. Of particular importance should be given to wooden buildings, because they are in the main risk group. Mold can spread on any surface, the main condition for rapid development is the maximum humidity. Colonies are developing on the ceiling, floor, wall or in the corners. If a certain zone is not insufficient, as often happens in the steampers built with their own hands, then the mold will appear there first.

If you have noticed the first signs of fungus, you need to immediately begin to exclude it. There are three basic ways to destroy mold spores: mechanical, folk remedies, stores. Conditions are:

• The first option is stripping the damaged surface with a brush or grinding machine. If, when removing the fungus, the damage was detected of the entire bar, then it is subject to a complete replacement.
• Folk remedies for the fungus or the finished store mixtures imply the processing of infected areas by aggressive substances of surface or deep penetration.

Ventilation system processing

Before proceeding with the disinfection of the walls, the ceiling, corners or floor from the fungus, you should check and well process the ventilation system. First of all, you need to open the shifts and examine the cavity that serves as a ventilation channel. Clean any blockages, dirt, eliminate the acquired damage. Many owners of the bath eliminate the source of the fungus, installing the fan near the ventilation grilles. The device promotes the necessary air movement.

You can handle the ventilation system specially intended primer. The tool should go exclusively to eliminate the fungus, and not for prevention. It is necessary to choose a drug that works with wood, clearly stick to dosage and precautionary measures to not damage yourself, do not burn the skin. After each processing, it is necessary to air and dry the bath.

How to remove the fungus in the bath on the walls

Stores offer a wide range of funds. How can I bring the fungus in the bath? Most people apply the Dedovsky method using copper vitrios - it is considered the most effective. It is necessary to thoroughly dry the surface, make a solution according to the instructions and bring it to the walls. The procedure should be repeated in a couple of weeks. How can I handle the walls from fungus yet? Covered surfaces with acetic acid of 70% or white in pure (not diluted) form. This is a temporary solution to the problem: first should be repaired the ventilation system.

What to do if a fungus appeared on the floor in the bath

Infection of sex fungus in the bath is a common phenomenon. It is advisable to disassemble a militant surface with mold, in the process of this remove part of the soil, which can also be infected. The affected boards should be replaced. The rest of the floor of the room should be treated with an antiseptic agent. To avoid the appearance of mold in the future, the bath must be used daily, and after use - to air for a long time. In this way, you get rid of the reason for the appearance of mold and keep yourself from diseases that mold causes.

Than to handle a bath from mold

There are many means that help destroy mold. They can be used in the store in the form of a finished solution, and do it yourself. Antiseptics for surface and deep use is better to buy well-known and proven brands that guarantee the protection of boards and a positive result to eliminate mold. This, for example:

• Biotole;
• METAS-BIO;
• Cerezit;
• Dali;
• Neomid bio;
• Erlin;
• Pentatos.

From folk remedies than you can withdraw the fungus in the bath, choose:

• Chlorine lime, which consists of a negro chlorine lime and simple water. It is applied to the dry surface.
• Copper sipop: It is sold everywhere in stores that specialize in horticulture. If you do a solution on a liter of water, then you need to take fifty grams of vitriol, one hundred grams of alumokalia alum and thirty grams of cook salt.
• Sere, the price is low, and the result is fast and perfect. In the refractory capacity (pelvis, bucket), a sulfuric checker is set on fire, which in the burning process highlights gas, destroying the spore fungus in the entire room.
• The hydrogen peroxide in 20-25% is applied on wood and leave for several hours, and after wiped with a rag moistened in water.
• The usual whiteness, which can be bought at an affordable price in business stores. After applying this substance, the walls should be additionally treated with water.

Mechanical stripping surface

If the penetration depth of the fungus is not very significant, then you can use the mechanical stripping of the affected area. For this purpose, construction tools and devices will be useful: spatula, emery, metal brush, grinding machine. After the visible plots with mold will be removed, the waste is desirable to burn to prevent the development of fungus on other objects. Mechanical cleaning is used also with deep penetration of mold, drinking a piece of wood and inserting a new material there.

Treatment of wood from fungus folk remedies

What to bring the fungus in the bath? Folk remedies tested by not one generation are best help. Chlorine lime, copper vigor, sulfur checker, hydrogen peroxide and household whiteness copier with fungus, distinguished low price. When using these compositions, you should adhere to the preparation instructions, as well as to wear a protective mask so that there are no pairs of harmful substances in the body. In the case of a sulfur checker from the room, you need to exit, and the windows, doors and all the slots are tightly closed.

Antiseptic tools from mold

In addition to the mechanical getting rid of fungus or the use of folk remedies, it is recommended to acquire both professional preparations. The stores of surface and depth penetration, which are completely different for the price will be perfectly cope with mold. What to bring the fungus in the bath for a long time? The choice is better to stop on the goods of proven manufacturers, such as Biotol, Metas Bio, Ceresite, Dali, neomid Bio, because the chemistry of little-known firms may not help, and the money will be spent.

Price of means for removing fungus in the bath

Many owners make a decision than handling fungus in a bath, pushing out from the price of the applied tool and method. Mechanical processing in the presence of all tools will be the fiscal itself. A little more than impregnated by folk remedies. The price of store antiseptics is ambiguous. It all depends on the fame of the brand producer, but in most cases it is high. Options how to destroy mold, weight - you should choose an acceptable one for you.

Video: What to treat a tree from mold and fungus

Found in the text error? Highlight it, press Ctrl + Enter and we will fix everything!

Discuss

What to bring the fungus in the bath

Fans of the bath may be interested in talking on a serious topic concerning dampness, as well as the consequences to which permanent stay in the bath can lead, namely, the growing of mold. In this article we will tell you in detail about how to bring the fungus in the bath.

Mold is microscopic mushrooms, which, with humidity, exceeding 60%, and without proper ventilation, are capable of quite quickly spreading almost on any surfaces. It is believed that this dangerous flora arose on our planet before all living beings appeared.

Mold mushrooms are quite dangerous for the human body, as they can provoke various diseases, from allergic reactions, to the development of skin, eye, pulmonary, gastric, and even oncological diseases. Therefore, in order to prevent such an outcome, it is better to eliminate the foci of spreading mold, without giving it to spread in the future.

Even before construction it is worth considering:

• As a material for the construction of a bath, it is better to use a forest fired in winter. In the autumn period it is better to restrict ourselves to the laying of the foundation, and with the arrival of spring already build the bath itself.
• Special attention is paid to the quality control. Try not to take even healthy wood if it germinates next to the defective tree. We can assume that it is also infected, and when it appears on it and it will begin to deteriorate, only the question of time.

Better, if a moisture meter is at hand - it will greatly simplify the process of choosing the desired tree.

During the construction of a bath, remember:

• The underground, the attic and the ribs of the frame be sure to arrange product.
• On the foundation and supporting structures to put quality vapor and moisture insulation.
• Think over and install an effective ventilation system.
• All surfaces in bathrooms are treated with an antiseptic matter.
• Implement the slopes, ceiling and external walls to exclude their freezing.
• If windows with double-glazed windows are installed in the bath, then you should insert valves for ventilation.

During operation, you should not forget about such recommendations:

• Try on time to repair damaged plumbing and communications.
• In time, clean the ventilation channels, as well as check the functionality of forced ventilation.
• If there is an opportunity to carry out permanent heating, it will have a positive effect on the bath, because it will prevent the appearance of mold, and the construction will last longer.
• Do not leave any raw fabrics in a unwanted bath, always provide them with complete drying.

In addition, make a timely full cleaning of the bath, because the mold in the mud also spreads very quickly. You can always take advantage of special means to maintain hygiene in the bath.

Well, the main question is how to get rid of the fungus in the bath

If constant heating is not performed in the bath, then, most likely, the mold will appear in it, especially if it is made of wood.

The fungus is notable for what may occur anywhere where dampness is constantly present.

If you still discovered the first places affected by mold, you will need to resort to one of the methods described below the method of deliverance from this ill-fated fungus.

Relief from fungus mechanically

Before treating the fungus in the bath, it is worth deciding with the depth of the defeat. Based on this, such tools can be applied: spatula, sandpaper, brush with a steel pile, a drill with a brush, grinding machine and so on. All removed waste is preferable to combustion.

If the mold penetrated the inside of the wood, then only the complete replacement of the damaged area will help. In some cases, parts of the bars are drunk, and new ones are built in their place.

Before removing the fungus, be sure to wet the surface to be processed so as not to give it to spread through the air.

The use of folk remedies

Some experts note the inadmissibility of the use of chemicals to get rid of the fungus in the bath - how to get rid of it in this case, we will tell further. There are several solutions to the problem.

The use of chlorine lime. A solution of an onset chlorine lime with water is applied to the purified dry surface. Sometimes formalin is added to the solution. Such a composition is fighting perfectly with fungus.

You can use copper vigor. 50 grams are divorced in 1 liter of water, 100 g of alumokalia alum and 30 g of cook salt are added there. Apply a roller, brush or spray. Do not forget the use of protective equipment when operating such a mixture.

There is another way to help get rid of the fungus in the bath as soon as possible - this is the use of sulfur. All the ventilation channels, doors and windows are closed for this. In a fire-resistant container, a sulfur checker is settled in the calculation of 2 g per 1 m 3. The method is considered quite dangerous, so in the room at this moment no one should be. After 6-8 hours, a container can be added to the room with a negated lime, which in a couple of hours absorbed the formed gas and dried air.

If the mold was formed in the bath on the lining, for example, it can be treated with hydrogen peroxide. To do this, 20-25% peroxide solution are applied to damaged wood areas, and left in such a state for several hours. After drying, the surface can be wiped with a damp cloth.

How to remove mold in the bath, if it is still fresh? A simple "whiteness" or "Domasetos" will help, which can be purchased at any economic store. The tool is also applied somewhere for an hour, after which it is washed off with clean water.

It is worth noting that the bath furnaces are valued for the fact that they are quite quickly warming up - in just 2-3 hours it is already possible to start bath procedures. But minus them is that they cool quickly - just 1-2 hours. During this time, the premises do not have time to succumb, and this is the answer to the main question, why the mold appears in the bath, it would seem without visible to the reasons.

Existing on the market at the moment the means of fungus

On the market you can find a lot of various antiseptic tools, both superficial effects and deep penetration.

It is very important to get rid of mold in the bath, the faster, the better. When choosing, than to destroy the fungus in the bath, you should pay attention to the means like Biotol, Dufa, Metas Bio, Ceresit, Neomid-Bio, Dali, and so on.

It is difficult to say which remedy is best in a specific way. The main thing is to buy proven brands in reliable stores, as well as beware of too cheap tools.

In this article, we described in detail how to remove mold from a tree in the bath, and what means it is better to use. It is worth noting only what is better to carry out timely prevention than to deal with the consequences. And then your bath will serve you as long as possible, pleaseing you and your loved ones.