Why appears condensate on cold water pipes, what to do in this case? Condensate - the problem is common, and it can act on both metal and plastic pipelines. At first glance, the problem is insignificant, but over time it delivers a lot of trouble in the form of rust, mold and an unpleasant smell. That is, the condensate is still needed to get rid. To do this, it is necessary to find out the reasons for its appearance. Why sweat pipes?

Why condensate appears on cold water pipes

Most often you can watch condensate on pipes in the toilet. One of the reasons is the water leak in the tank. Water is constantly changing and does not have time to warm up, hence and humidity. Get rid of leaks in a tank - this reason will disappear.

Sometimes there are puddles from an excessive moisture. So, the leakage in the tank is in the living neighbors living above. At night, listen to the murmur of water in the sewage, and you will immediately understand everything.

Another condensate is formed due to increased humidity and temperature drops. To avoid condensate, you need good ventilation. To start, just leave the door on the night to the toilet open, perhaps in the morning you will find a dry pipeline.

The reason is obvious - clogged ventilation pipeline. Out the grid on the ventilation channel and read everything very well. In the ventilation channel should appear.

In the event that there is ventilation, but it does not cope with the problem, you can install an exhaust fan. It is attached instead of a ventilation grid, and you turn it on as needed.

The choice of fans in modern building supermarkets is huge, for every taste and any price. Recently, the installation of such fans in the toilets and bathrooms is very common.

How can you eliminate the problem of condensate

How to get rid of condensate on the tubes in the bathroom? Also sweep pipes in the bathroom. The reason may be similar. Condensate on the riser - problems with plumbing in the neighbors. Wash the water supply to your plumbing, the faucet works well. No hood, as in the first case, aggravates the problem.
If systems with hot water and cold are very close to each other, fogging can not be avoided.

It is necessary to do thermal insulation of pipes, it is excellent protection that will allow to remove condensate.

Often condensate is formed on pipes in the bathroom due to faucet fault. Water leak contributes to their cooling. Output one - crane repair!

How to get rid of condensate? Fully get rid of pipe fog will allow insulation for pipes. It is necessary to isolate cold water pipes from interaction with the external environment. There are special thermal insulation materials using which you can save pipes from condensate. It is easy to just buy such a material and insulate pipelines. The abundance of such materials on the construction market of materials is very large.

In the event that you prefer the budget option to eliminate the humidity on the pipes, and do not plan to buy an expensive heat-insulating material, you can use other paths. It is necessary to purchase a balloon of the mounting foam and a plastic tube or corrugation, the diameter of which exceeds the diameter of the pipe with condensate. Corrugation or pipe is cut into pieces so that you can put them on a problem tube, then wear and emptiness is filled with mounting foam.

There is another budget option to get rid of condensate. You will need sandpaper with rust removal and acetone, so that after that it is well deprived of the problem surface. It is best to treat the pipeline with phosphoric acid and then apply a layer of epoxy putty on it so that it does not flow.

Then immediately wrap the pipeline in advance prepared fabric strips in such a way that the matter is soaked with putty. You can use the old sheet, cutting it into pieces, similar to bandages. Putty with a cloth quickly frozen.

You can make the same way several times. The work ends with the application of the finish putty. It will aesthetically look if the putty is stabbed and cover the water-free colors you need.

In most cases, thermal insulation of pipes allows to solve the condensate problem, but sometimes the level of humidity in the house or apartment is so high that waterproofing of the floor and walls is necessary.

A rare person did not have to face such a phenomenon as condensate on the surface of the cold water pipeline. Although this unpleasant phenomenon may occur on other designs - windows, outer walls, in the corners of the premises.

The reason for the occurrence of condensate are pairs of moisture contained in the air. In contact with the cold surface, they cooled and turn into drops. The higher the humidity in the room and more the difference in air temperatures and the cold surface, the greater the likelihood of this unpleasant phenomenon.

If the house is chronically "cry" pipes and windows, then urgently need to be dealt with the causes of this phenomenon.

These include such premises as the bathroom and toilet. It is there that the risers of cold and hot pipelines are usually located.

There are several reasons for water condensation on pipes:

• bad ventilation of the bathroom and toilet, leading to the preservation of high humidity in them and increase the total temperature in these premises;
• in the toilet, the problem of the problem can be a malfunction of the valve overlapping water in the toilet tank - the leakage of water leads not only to its leakage, but also to the constant cooling of the pipe with cold water;
• in the bathroom, condensate is often formed for the same reason - faults of the valve of the mixer overlapping cold water;
• high humidity in an apartment or house caused by many malfunctions - bad ventilation, current roof, incorrectly selected insulation.

If condensate began to form recently, then the reason should be immediately found out, and not wait when the problem becomes chronic. You may have recently changed windows or installed in the house any equipment contributing to the "warming of microclimate".

It must be remembered that although condensate is just water, it is it that is the main aggressive medium that destroys steel structures, including pipes.

In addition, excessive moisture is sooner or later, it will be the reason for the appearance of fungus and mold not only on the pipes, but at any points of the apartment where there are cold surfaces.

And this is no longer just ugly, and often even dangerous for people living in the house, especially allergies.

How to act when the peating pipes appear

The algorithm is very simple - you need to find the cause and eliminate it:

• You can start with checking the drain system of the tank and shut-off cranes. To do this, you will have to watch them. Sometimes people leaving the bathroom, do not notice that the faucet is drunk, and the toilet valve is periodically opened due to lowering the float level due to a small leakage of the tank.
• Check the performance of the ventilation using the paper sheet or the lifting matches to the ventilation grille. If the piece of paper falls, and the match is burning smoothly, it means that the ventilation does not work.
• If you didn't find faults in your apartment, you will have to visit neighbors from above and find out from them, they faced with the same problem. A malfunction on any floor located above leads to a constant circulation of cold water in the pipe, which significantly reduces its temperature.

• If you have forced ventilation in the bathroom and toilet, then it is worth checking the effectiveness of its work.
• If everything is in order, but the pipes "cry" means the reason for this is that the difference in the surface temperatures of the pipe and the surrounding air exceeds 17 degrees, and to solve the problem will have to use special methods.

Options solving the problem

The main idea of \u200b\u200ball the following methods is the thermal insulation of the cold water pipeline to reduce the intensity of exposure to it too warm air.

• Painting pipes insulating paint. This is quite expensive, but the effective way to solve the challenge. It is worth the patience here, because to achieve the necessary effect you will have to paint the pipe at least 5-6 times. Each previous layer of paint needs to dry well and only then apply the next one. At the same time, the premises will have to be forced to air - for this it is suitable for an ordinary fan.

• Pipe isolation with overlays made of foam insulator. The linings are soft pipes with a longitudinal cut. They are put on a dry pipe as a cover, and the edges then glue. To achieve the desired effect it is very important that the size of the lining is perfectly matched the pipe diameter. If it is more, then the effect will not be at all, and if less, then you will not be able to glue the edges of the lining. You can combine the two previous ways: first paint the pipe, dry the paint and put over the lining on it, which can also be painted with heat insulating paint.
• Having put on the pipe with a plastic pipe of the larger size and filling the space by mounting foam, you can also achieve good results. But it is important that the foam completely and evenly filled the space between the pipes, otherwise the method will not work.
• Independent creation of thermal insulation on the surface of the pipe. This is an inexpensive, but troublesome way, which is a completely reliable solution to the problem.

To create it, you need to stock in the following materials:

• epoxy putty;
• simple cotton fabric (for example, old sheets);
• strong thread or thin twine;
• putty knife;
• sandpaper;
• means for cleaning pipes from rust;
• acetone or other suitable substance for degreasing the surface of the pipe.

The fabric should be cut into strips of about 10 cm wide and wind into rolls. You can use medical bandages of a suitable width.

Next, we act as follows:

• The pipe is cleaned with paint and carefully degrease its surface.
• Next, pipe treatment with rust means is performed.
• After drying the pipe to it, it is necessary to apply a layer of epoxy putty and immediately quickly wind up the cloth from the bottom up. At the same time, the coils of the fabric should be superimposed on each other and soaked with putty. Then the fabric is fixed with the thread.
• After drying the first layer, several more are applied in the same way.
• At the end of the work, the pipe is still over with a putty.

After the insulation is finally dried, it can be seized and painted paint suitable color.

In solving the problem of "crying" pipes, the main thing is not to miss the moment until the pipes started corroded.

If it fails to eliminate the problem by eliminating leaks in plumbing valves and good ventilation, it is better to immediately resort to thermal insulation.

Causes of the appearance and methods of eliminating condensate on cold water pipes.

Condensate on pipes is an unpleasant phenomenon that can cause the development of fungus and mold. In this article we will tell how to deal with condensate on pipes.

Why is condensate for cold water pipes?

There are several reasons for the occurrence of droplets on the pipeline.

Condensate on cold water pipes, reasons:

• Bad ventilation
• The close location of the wiring of hot and cold water. More often happens on the surfaces that are summed up to the mixer
• Wrong mounting plumbing

Condensate appeared on cold water pipes in the apartment

The main cause of water droplets on the water supply is bad ventilation. If you are not sure, you can check and conduct an experiment. To do this, you need to open the door to the bathroom or the room where the moisture is going, for the whole night.

Why appeared condensate on cold water pipes in the apartment:

• If the outflow water pipe will be dry, really business in ventilation. It will be necessary to control the condition of the ventilation channels, if necessary, make their cleaning. Often the problem solves the installation of an exhaust fan, which sucks the air, and excess water from the house.
• With a sharp drop of temperature, moisture also occurs. Usually you can see in the summer when it is very hot in the apartment, and the water is cold enough. Forthis point The dew is on the surface of the water supply, as a result of which the moisture droplets appear. In the summer, water can flow with a stream, and accumulate in significant quantities. Some household owners have to install basins, containers for collecting fluid, so as not to flood their neighbors.

Sweats tap: reasons

Please note that there are several reasons for which humidity in the room can increase. This is not always a large amount of water procedures that are held in the bathroom.

Sweats tap pipe, reasons:

• Sometimes it is not connected with the bathing of households. Although this in most cases is of great importance. It is recommended after bathing in hot water, wide open the door to release all pairs from the bathroom.
• The second option is accommodation in conditions with high humidity. Indeed, in mountain conditions, too nearby rivers, water bodies, dampness can be observed. Therefore, a high humidity is also observed in the bathroom. It is possible to eliminate it with thermal insulation materials.
• Sometimes pipes sweat when changing weather conditions. It happens more often if it rains for several days in a row, or a long thaw is observed, with water stool on asphalt. Accordingly, water particles can accumulate in the indoors.
• Often, water droplets are formed on the pipeline, if the things that have been put on the batteries or ropes are dried in the bathroom. This increases moisture in the room, respectively, the remnants, water droplets, settle on the coldest surfaces.

Condensate on cold water pipes, what to do?

In this case, it will have to solve the problem not with ventilation, but with thermal insulation. What problems solves thermal insulation? First of all, it allows you to shift the dew point, and level the temperature difference.

Condensate on cold water pipes, what to do:

• It will not be hot air indoors and contact it with a cold surface. Accordingly, the moisture will not accumulate. There is a mass of methods, with which you can perform insulation of the pipe.
• It is usually carried out using special devices. Now on sale you can find special foam boxes that envelop the water supply.
• They consist of two halves, which are snapped with special grooves. Thanks to this method, it is possible to get rid of moisture. Such isolation is almost hermetic.

How to protect the tap pipe from condensate?

There are other methods with which it isolation of pipes with cold water. This can be done without purchasing special devices.

How to protect from condensate Water pipe:

• To do this, it is necessary to Occhat the surface of the pipe using sandpaper paper with small grain. Next, the processing is carried out using the solvent to remove the dust residues, and fat, which will prevent normal coating.
• After that, it is necessary to cut any cotton fabric on the strips of approximately half the meter long, and 3-5 cm wide. The thinner of the pipe, the more subtle should be the tissue strips.
• With the help of a special thread, the fabric is attached from above, and is wound to donomose. Now it is necessary to carry out the processing of epoxy paint. Please note that if necessary, you need to apply several layers of fabric and cover paint.
• Each subsequent layer is applied after drying the previous one. After that, the surface is carried out to remove small irregularities, jar.
• The last layer is applied with the use of spray gun so that there are no divorces, grains or strips from the brush. This allows you to significantly reduce the problem, or completely get rid of it. Due to the fact that there will be no collision of the hot and cold surface, the dew point will disappear.

Drips condensate with cold water pipes, how to remove?

You can also apply other methods, modern funds, as well as some materials allow it to do. Another interesting and unusual way is the use of thermal insulation material.

Drips condensate with cold water pipes:

• It can be foamed polystyrene, polyurethane, or the simplest mineral wool.
• However, these methods are used if a large diameter tube is located on the street.
• For home, such methods like mineral wool, in order to eliminate pipe fog, is not used because of harmfulness, and not a very pretty appearance, which will not fit into modern repairs.
• Often such pipes are simply sewn in the box of foam and drywall.
• To eliminate excess moisture use special chemical coatings, the principle of operation of which is based on to shift the dew point.

How to paint the cold water pipe from condensate?

Paints, despite the very thin layer of application, perfectly cope with the problems of the appearance of the dew point. The paint contains particles of ceramics, inside which are air bubbles. They seem to reflect warmly and do not let it inside the pipe. Paint, like a mirror, reflects heat and does not allow it to touch the pipe.

Such materials were initially developed for the space industry, in order to cover ships. Now, such chemicals for thermal insulation are used when coating the facades of the house to apply on pipes with hot, cold water, in order to prevent fogging.

How to paint the cold water pipe from condensate:

• Asthemisol
• Astrathek
• Corundum
• Stermezol.

How to isolate the cold water pipe from condensate paint?

All these means must be applied in a certain way. Prerequisite is the removal of water, drying the pipe. It will be necessary to stop the water supply for some time so that the pipe be heated, and it was possible to remove moisture from it without further accumulation.

How to isolate a cold water pipe from condensate paint:

• After that, the surface of the pipe is burned, small scales of paint and rust are removed from it, if it is available, after that degreasing is performed. It is carried out usingWhite Alcohol, or acetone.
• You can use another organic solvent, which does not leave a fatty plaque. After these manipulations, it is necessary to process the tools that are indicated above. Typically, the coating is applied in several layers.
• Each subsequent layer is applied after drying the previous one. The most recent, final stage is the coating with a special fixer. It is he who helps to preserve all the layers of thermal insulation material for a long time.

Video: Purge pipes in the bathroom

On the cold water pipes in the bathroom and in the kitchen, condensate is often detected - water drops, which are formed with different intensity. Sometimes they resemble the dew, but in difficult cases are collected in the streams, waterfalls and puddle, which causes a lot of problems. To avoid serious trouble, you need to know why condensate appears on cold water pipes, what to do when dropping drops and how to prevent their education?

Before starting the fight against condensate, you need to determine the reason for its appearance. Practice shows that usually several factors are "fogging" pipes, and they must be eliminated, otherwise moisture after a while will appear again.

Increased humidity

The most common cause of condensate formation - increased humidity, which may appear under the influence of the following factors:

• building defects, violation of construction technology, poor-quality hydro and thermal insulation;
• geographical features of the region - the presence of large water bodies near, rocky soil, wet climate;
• adverse weather conditions Long precipitation.

If all of the above is excluded, you need to look for a source of high humidity in the dwelling itself. It may be evaporation from wet linen, couples from being prepared food and other factors that are always present in the field of people's stay.

For reference! Condensate can appear on pipes from any material - metal or plastic, and in the first case it is especially dangerous. Permanent humidity leads to corrosion, Wear and serious breakdowns of plumbing equipment.

Equipment malfunctions

Another common cause that causes the formation of condensate in the toilet - malfunction of sanitary equipment and ventilation.

1. Bad ventilation. The target purpose of the bathroom and the toilet implies normal air circulation, otherwise the condensate will constantly form.
2. Incorrect installation of the pipeline. If the pipes for hot and cold water are installed at a minimum distance and are equipped with thermal insulation, water droplets can appear on the surface.
3. Faulty mixer. The mixer breakdowns lead to the cooler of engineering equipment, which is why condensate acts at night on the surface of the pipes. It is easy to determine the faults of this element easily - water is constantly dripping or soaked.
4. Valve breakdowns or tank cranes. The condensate formation mechanism in this case is the same as in the previous part of engineering communications cools, which leads to "fogging".

In apartment buildings, the cause of pipe humidity may be in the fault of the pipeline and plumbing equipment in the neighbors from above. Usually in such cases, condensate is not formed on highways that lead directly to the plumbing, but on the riser. Accordingly, it will have to solve the problem together - the fight against condensate in the same apartment will not give the desired result.

Attention! If the water supply is laid in an open way, it is possible to get rid of condensate using a waterproofing layer. It is much more difficult to cope with the nuisance in cases where the pipes are in the wall - it is hardly possible to do without serious repair work.

Other reasons

Most often, water drops are found on pipes in the summer, and in a strong heat, the situation can become catastrophic. The reason for this phenomenon is noticeable temperature difference Environment and fluid that flows through pipes. Especially often intensive "fogging" of pipes is observed in houses and apartments with metal-plastic windows, which are poorly passed by air and create a greenhouse effect.

Note! Owners of private houses and apartments on the lower floors of buildings when condensate is detected, it is necessary to check basement. Sometimes the source of high humidity becomes the breakthroughs of the pipeline and flooding, and the other manifestations of the problem may be absent.

What is dangerous condensate on pipes

Water drops on the surface of the pipes - not a small household trouble. First, the owners will have to constantly wipe or leaving the liquid, but over time the condition of the bathroom it will only worsen. Increased humidity causes a resistant smell of dampness and creates a favorable environment for the development of fungi and. Their disputes scatter through the air and fall into the respiratory tract that may cause serious diseases.

Moisture on metal pipes creates an aggressive medium, contributes to corrosion of the material and the rapid output of communications. No smaller harm water shall apply to floor and wall coatings - they begin to crack and fall behind, and sooner or later in the bathroom will have to make a major overhaul. If the liquid lens to the neighbors, which happens quite often, two rooms will have to be put in order at once.

Financial costs in the formation of condensate may be associated not only with repair work, but also with municipal accounts. If there is leaks in the tank or mixer, the owners will have to pay for water that goes nowhere. At first, the difference may be minimal, but for several months "swears" an impressive amount. The output from the situation is to start solving the condensate problem immediately after it appeared on the surface of the pipes.

Tip! If it is impossible to immediately solve the problem of condensate, and water droplets cause serious inconvenience, temporary measures can be used. For this pipe, the pipes are wrapped with a piece of conventional bandage, and the free end is lowered into any capacity, due to which the liquid will not accumulate on the floor.

How to get rid of condensate

Before taking measures to combat condensate, it is necessary to conduct a large-scale check of communications and ventilation. If you cannot eliminate the cause of excessive moisture, water drops over time will appear on the surface of the pipes and sooner or later other problems will cause.

Ventilation repair

First of all, it is necessary to inspect the ventilation system. Check the quality of ventilation is simple enough - for this, at night you need to leave the door to the room open. Dry in the morning pipes indicate poor air circulation in the bathroom. The second way is to bring the flame (lighter, match) or sheet of paper to the lattice. If they are tightened towards the ventilation channel, the system is in order, and otherwise we can talk about clogging or faults.

The grille and the remaining items must be cleared, remove trash, dust and cobweb. It is best to organize forced ventilation in the bathroom, since conventional air circulation systems do not always cope with their task. Compact fans are sold in stores with different power, which are installed instead of a ventilation grid.

Prices for exhaust fans

Exhaust fan

This is especially true for apartments and houses with additional heaters and metal-plastic windows. If the temperature difference between water in the pipeline and indoor air is more than 17 degrees Condensate will appear constantly. To improve the circulation, you can increase the lumen under the door and after hygienic procedures as often can be left in the bathroom open.

Repair of engineering communications

If ventilation is in order, you need to explore the entire pipeline in the bathroom, toilet and the kitchen. Usually leaks and malfunctions are visible to the naked eye. In rooms where pipes are laid in the walls, it will be more difficult to identify the problem. To do this, you will have to partially disassemble the box covering the pipeline, or call professionals that determine the malfunction using special devices.

All leaks need to be eliminated, and most often the malfunction is found in the mixers. A thin trickle that flows from the bottom of the crane often becomes the cause of condensate. To eliminate the leak, you need to replace the gasket or cartridge, and if necessary, buy a new mixer. Special attention should be paid to the tank - if the sound of current water is constantly heard in the toilet, it means that the container is not dialing to the end and is constantly updated with cold water.

A good solution to the condensate problem, which appears due to water in the tank, can be a double design. Inside it is additionally installed plastic container where the liquid is recruited. It does not come into contact with the walls of the tank, so "fogging" of pipes is excluded. The shortcomings are that such devices are expensive and most often sold complete with the toilet.

Video - Easy way to eliminate condensate from a tank

Sometimes it is not limited to the replacement of small parts of the water supply - you have to change individual areas of pipes. In the case of plastic pipes, this can be done independently, pre-break the main crane. Metal structures can only change plumbing workers with special equipment.

If ventilation and communications are in order, you need to ask the neighbors from above to inspect the bathroom - perhaps the leakage occurred from them.

Attention! Independently repairing ventilation systems and plumbing equipment in the absence of special skills is not worth it. It is better to contact the management company - its employees will eliminate all malfunctions, blockages and breakdowns.

Installation of thermal insulation

If all problems with ventilation and engineering equipment are eliminated, and condensate still appears - the reason lies in the temperature difference. In this case, it will take thermal insulation of cold water pipes, which is performed using special materials or protective chemicals.

The easiest option is to purchase gaskets from a special foam material. It is sold in the form of soft hollow rollers with a cut and is used very simply - it is put on a pipe, like a cover, after which gluits. The main thing is to correctly select the diameter of the lining, since too big will not give the necessary effect, and too small cannot be glued.

Popular materials also include mineral wool (produced by blocks or rolls depending on the diameter of the pipes) and polyurethan. They demonstrate excellent thermal insulation characteristics, but have features of use and laying.

Prices for pipe heat insulation

Heat insulation for pipes

Liquid thermal insulation

A simple solution in the fight against condensate, which often gives a positive effect - cover pipes olife or oil paint, as well as protective primer. It is bred with oil or epoxy varnishes, apply to the surface of the pipeline and, after drying, paint in conventional paints. The slots in the walls and the floor are recommended to close carbolate - Mass resembling pasta. Carbolate is applied to the working surface, leave for 24 hours, After that, it is squeaked and painted with oil paint.

Video - Practical application of liquid thermal insulation

The second option is to cover the surface of the pipes with a special chemical composition. They possess different characteristics, but perform the same task. To choose the right tool, you need to pay attention to the following parameters:

• price - high-quality thermal insulation can not be too cheap;
• paint weight It is no more than 7-7.5 kg per 10 liters, and in too heavy mixtures there are probably foreign mixtures that reduce the effect of use;
• built-in compositionwhich is noticeable when light should be small;
• color in real liquid thermal insulation must be white as well as attend the unseen smell of ammonia;
• reviews About the products of certain manufacturers on the Internet can say a lot about the quality of funds.

Table 1. The most popular thermal insulation formulations for pipes.

Prices for liquid insulation

Liquid thermal insulation

The only drawback of liquid thermal insulation mixtures is that they are sensitive to storage conditions. The composition that was stored incorrectly may lose its characteristics, so you need to buy products in proven stores and use as quickly as possible. In addition, it is important to properly apply to isolate the pipes and protect them from condensate.

1. Clear work surfaces From rust and dirt, you can use special chemicals.
2. Processing pipes in primer For better adhesion thermal insulation with material. Features of the use and drying time of soil compositions are indicated on the package.
3. Apply thermal insulation mixture on pipes. Difficulties This process usually does not cause - the means are applied as any paint using roller, tassels or spacing. You need to apply from 3 to 5 layers, and each of them requires pre-dry.
4. Top it is recommended apply a special fixer, Which will protect the coating and give the pipes aesthetic appearance.

Important! When buying materials and mixtures for thermal insulation of the pipeline, it is important to pay attention to the choice of funds - they must fully correspond to the material, diameter and other characteristics of pipes. If you are mistaken at least in one parameter, their use will not give the necessary result.

Heat insulation with epoxy and cloth

A difficult and time-consuming method of thermal insulation of pipes, but experienced plumbers consider it the most durable and efficient. For him, the following materials will be required:

• epoxy putty;
• cotton fabric strips 5-6 cm wide;
• durable thread;
• acetone;
• rust solvent;
• grinding paper.

The amount of materials is calculated depending on the thickness of the pipes and the magnitude of the site that must be processed.

Table 2. Thermal insulation of pipes with tissue and epoxy putty - step-by-step instruction.

Photo	Step, Description
	Step 1. Tuba Okolkit, degrease acetone and handle rust converter, give a good dry
	Step 2. Apply an epoxy layer on the surface, after which it is quickly wrapped with a cloth and fix a durable thread
	Similarly, to make another 2-3 insulating layer from the fabric, on top of the applied layer of putty
	Step 4. Wait for a complete drying of thermal insulation, after which itching the pipes and cover their paint

Do not forget that thermal insulation in any form can be used only for whole pipes without leaks and cracks. If the pipeline proceeds from above, materials and mixtures will only exacerbate the problem.

Tip! If, in the absence of leaks and other problems on metal pipes in the bathroom or toilet, condensate constantly accumulates, you can resort to time consuming and expensive, but effective solution. It implies the installation of polypropylene pipes instead of a metal - thermal insulation layer on their surface is usually formed at the stage of production.

How to choose a condenser

Condencators - Special devices that automatically remove excess moisture. They are installed in places of the largest condensate accumulation and most often used for industrial purposes, but you can install the device and in the residential room. Depending on the principle of operation and design, the condensate trap is float, thermodynamic and bimetallic.

1. Float. The principle of their work is based on the difference of the physical characteristics of steam and liquid. The devices are equipped with a float and lever, which are connected by the valve. After moisture accumulates in the case, the condensate is triggered, the float rises and produces surplus. Such devices are installed only in heated rooms, as prone to freezing.
2. Thermodynamic. The device is a dial tube, the principle of operation is based on the difference in the speed of the steam and fluid. Thermodynamic codencators are also prone to freezing, and still work quite noisy.
3. Thermostatic and bimetallic. The basis of the mechanism is the principle of changing the aggregate state of the fluid, depending on the temperature. These are reliable and compact devices that can work in any conditions.

When choosing a condensate, you need to consider different criteria, so the task for buying and installing the device is better to entrust professionals. Most often, float devices are installed in residential buildings that have an acceptable cost, simple and easy to use.

Solve the problem of condensate should be started as soon as possible - Immediately after water droplets appeared on the pipes. If you put the problem on samone, it will become cause of serious financial costs On the replacement of the pipeline and repair the bathroom.

Condensate in the bathroom on cold water pipes

Before starting repair activities, it is important to accurately determine the cause of the problem that is usually as follows:

• When wetting the pipe, the riser is usually usually in the course of the neighbors from above.
• If the pipe is wetting near the plumbing device, then the reason lies in a faulty crane.
• In case of detection of ventilation problems, it will be necessary to work on eliminating blockages overlapping.

If condensate appears in the bathroom on the pipes: what to do in such cases? Listing ways to eliminate condensate, it is impossible not to recall the thermal insulation, which helps quite effectively in the specified problem.

How to get rid of condensate on plastic pipes

Frequently backed for the appearance of condensate are leaks in sanitary pribers. If the waterproof is mocking, feeding water to the superstrates, then the breakdowns can be in the crane, in the shower mixer, in the ads of the toilet tank. And the wet riser can say that leaks are available in neighboring apartments from above.

If the pipeline is laid from plastic, then the problem is to eliminate the condensate on plastic pipes, decide as follows:

• Checking the hoods and the ventilation grille change to the compact fan.
• The network isolation is insulated with special cuts with a cut. These products are offered in every construction store. They are made from energy flow and foam polyethylene. This is a very simple way, just before warming up, you need to thoroughly dry the pipes.
• The full insulation of plastic pipe rods can ensure the use of fabric strips and plastering. Above there is a detailed description of how it is performed.

Features of the metal plumbing pipeline

The problem is to eliminate the condensate on metal plumbing pipes worth not less acute than in previous situations.

Eliminate the condensate of metal pipelines help the following steps:

1. Nozzles protect against rust, dried and opened with olifa, oil paint.
2. Covered carbolate. This is a pasta tool for sealing the slots in the walls and the floor, it is applied by a layer of 0.5 cm. This composition should be stuck, and then the surface is squeezed with shallow sandpaper and paint oil paint.
3. Projector primers. They consist of zinc dust, which was diluted with Olife. This composition operates the highway, and then it is painted (enamel).
4. The mainstream in the toilet can be treated with the means, the basis of which is the olive and suicon, or special primers (for example: FL-031, FL-053).

How else do they cope with condensate

Video: How to eliminate condensate on plastic water pipelines

The elimination of condensate on pipes is not a simple task, without determining the exact cause of this phenomenon.

Experts on this subject express such an opinion.

• Professional plumbers advised to acquire "Gofroters". This is a special store that can be bought in building materials stores. It is superimposed on the surface of the pipes, and forms a solid and elastic film there, which prevents wet manifestations.
• Also, experts are confident in the effectiveness of liquid thermal insulation, which is applied to dry and cleaned highway.
• If the entire plumbing and the pipeline is in good condition, then condensate can accumulate due to the difference in the temperature of the nozzles and air. In this situation, only the insulation of the system will help. The most suitable option for such isolation professionals is called foamed polyethylene or merilon, which is not difficult to buy in any building materials store for low cost. Fasten this insulation, dressing on the pipeline. Fix it with a clamp and wire.

The fact is that in addition to the main, there are also side phenomena that lead to the formation of condensate. The source of dampness becomes evaporation from the basement, poor waterproofing and insulation of walls.

Because of this, condensate appears and frost. In such situations, the exit one is the insulation of the floor and walls in the house with high-quality material.

In addition to the already listed reasons leading to "wet" troubles, there are others. For example, weather conditions. Frequent and tightening rains, the close location of the reservoir, the proximity of groundwater also greatly increases the moisture index in the house.

It can be reduced by putting a moisture absorber or air conditioning having air drain function. Moisture absorbers offered in the modern market - an excellent method for eliminating moisture.

These are plastic boxes containing absorbent pills. When using these devices, get rid not only from fogging on the pipets, but also eliminate moisture in the whole house.

How to eliminate condensate on the cold water pipe, can advise specialists. If they are entrusted to fulfill this task, you can be sure that they will quickly and effectively eliminate the reasons leading to dampness in the apartment. And in this case, the health of people can not worry.

Condensate on pipes occurs due to the difference in the temperatures of the surrounding air and water in the pipe. Especially often such a phenomenon can be seen in the warm season. Excessive moisture on metal pipes leads to their rapid destruction, and on plastic pipes - to the formation of mold, so the cause of condensate is required to eliminate timely.

How to get rid of condensate on pipes basic ways to fight

The harmful effects of moisture on plumbing equipment and the premises makes thinking about the methods of combating condensate. Most of them are relatively simple and inexpensive.

Installing the exhaust fan in the bathroom

First of all, excess moisture is eliminated by the influx of fresh air. If there is no ventilation at all, it is desirable to organize it.

The work of the existing system may find out the garbage that has accumulated in the ventilation channel. You need to unscrew the grille and carefully cleaned the dust and web from the hole.

It is possible to make sure that the thrust can be brought to the opening a lit match. If the thrust is still insufficient, you need to buy and embed a fan in the channel.

Installation of insulating tubes

High-quality isolation is one of the most efficient ways. Efficient and inexpensive steamproof thermal insulation is made of foamed polyethylene. This material is called energyflex and sold in the form of finished tubes of various diameters or in rolls.

Before use, the pipeline must be dried, then cut the elastic tunnel along and put it on the pipe. The joints of the joints are treated with mounting foam and fasten with waterproof tape.

Application of epoxy putty

Homemade thermal insulation can be made from epoxy putty and old tissue trimming. The pipe is cleaned from traces of rust with grinding paper, wipe with acetone to remove fat and additionally a special means against rust.

Now it is applied by the main layer of epoxy putty and quickly wind up the unwinded surfaces of the rags. Motable two or three layers, the cloth is fixed with wire and the finishing layer of epoxy putty is applied on top of it. Now you need to wait for drying and you can clean and paint the surface.

Temporary methods

If there are no necessary materials, or at the moment it is impossible to carry out work, you can use in simple ways. But you need to remember that they are not suitable for long-term use.

• Wet a wet tube with a bandage and lower its tip into the water collection container.
• Constantly keep open doors.
• Eliminate moisture absorbers, for example, silica gel balls in the bags.

How to get rid of condensate in the toilet

The situation with the bathroom in the toilet is similar, but it is worth considering that for the second embodiment, the presence of a large number of pipes. If you are going to make a sewage system in a private house, it is better to immediately make a separation of cold water riser from hot or need insulation of pipes. There may be a regular process from the tank in the toilet.

It should be borne in mind that all materials have their own indicator of heat performance. But this fact does not force you to fully replace the pipeline, for example, from cast iron products on PVC. In order to correct the situation, there are many options. We will talk about them and talk on the article.

Methods of elimination of leaks

The reasons for the formation of condensate in the toilet and in the bathroom we have already found out. Now find out how to solve problems with the formation of leaks. The first thing to do is to find the place of water flow in the system. Its education can occur:

• If the faucet and the mixer has a malfunction. In this situation, you will observe a constant dripping of water from cranes.
• In the case of the formation of a breakthrough in the pipeline;
• Fitting wear.

The greatest complexity of the definition is a breakthrough of the pipeline and the unsuitability of fittings. To identify a malfunction you need to perform a partial disassembly of the box that closes the pipes. To facilitate the process, it is better to apply for the help of professionals. Experts can easily determine the problem with the help of thermal imaging - special equipment. It is worth noting that both options require cash investments. When you discovered leakage, you can do such repair activities:

• It is necessary to change the gasket. A set of tools for work can be bought in any specialized store. To make a purchase, you need to know information about the brand and manufacturers of the mixer. This work can be performed with your own hands.
• If after the repair procedure nothing has changed, then you must replace the mixer.

In the case when the pipeline of the sewage system in the house proceeds, then such measures can be taken:

• Replace the system with problems. To perform work, you need to cut the segment of the flowing pipe and mount a new item. In most cases, in the presence of a pipeline from a metal, the help of specialized techniques is useful. For this you can order a car from a specialized company.
• Install the plug on the pipe to the place where there is water leak. It is worth noting that this method is less effective, so it is not necessary to apply it.

Replace fittings on the pipeline will not be much difficulty. To do this, you need to remove an unsuitable detail and replace it with a new one. Before proceeding with such work, it is necessary to overlap the supply of water into the house.

How to remove condensate than you can wind pipes

Those who have encountered such a phenomenon immediately arises a question than to wind the pipe so that there is no condensation. Prevent the appearance of water droplets on the surface of cold water pipes can be in several ways, one of which is thermal insulation. This option is considered the most effective, since it eliminates the reason for their appearance - the temperature difference. It is easier and faster to solve the question by an insulating tube, cutting it along for convenient placement. For the manufacture of the tube uses foamed polyethylene, energyflex or thermoflex.

The process is as follows:

In the case when water drops appear as a result of a fault of a plastic pipeline, you can independently replace the damaged pipeline for a new knee. Metal pipelines can only replace plumbing workers who have special equipment and skills.

To prevent the formation of condensate on plastic cold water pipes, it is recommended to use the following types of insulating materials:

• Polyfoam or polystyrene foam is considered a universal insulation for pipelines made of polymeric materials. It is produced in the form of a shell consisting of two halves. They are connected to each other by means of a groove-cream castle. The use of such insulation is sufficiently simple: halves of the shells are put on the pipe and fixed with adhesive tape.
• Mineral wool for insulation of pipelines is produced in rolls, which largely simplifies the use of this material.
• Polyurethane foam refers to heaters with high insulating characteristics. The temperature range of such material is quite wide, from -160 0 s to +150 0 C. Practically all polypropylene pipes have such a layer, it is formed on products in the production process. In this case, the thickness of the insulation reaches 5 cm.

The consequences of high humidity

The main reason that condensation contributes is the increased humidity of the environment. That is why this process is characteristic of toilets and bathrooms, basements, boiler houses, laundries, etc.

Condensate-damaged surfaces have an ugly appearance. In addition, other dangers are boring his appearance. One of them is corrosion, which over time destroys metal structures. And also, permanent humidity loves a mold fungus, causing allergic and respiratory diseases. Both can not be called something pleasant and helpful.

The appearance of condensate on the tubes in the toilet

The cause of moisture condensation can be both high in air of steam and temperature drop. In the case when there is a condensate in the toilet on the pipes, it follows the first thing to check the ventilation - the easiest way to leave the door to the toilet open for the night. If the pipes are dry in the morning - the ventilation is insufficient.

Another common reason can be the constant tank flowing, in which the water does not have time to warm up in the pipe, replacing it is constantly cold, which is even more cooled by the sewer pipe, as a result of which it appears on the pipes in the condensate toilet. In this case, it is necessary to check and repair the cranes and the inlet valve of the drain tank.

Treatment of water pipes

Treatment of pipes of the water supply system is the most affordable and efficient by controlling condensate. Old systems consist, as a rule, from metal components and are more susceptible to leaks and corrosion.

Modern pipelines can be made of both durable plastic and from resistant to the destruction of metal alloys.

Metal pipes

Metal pipes under dampness are particularly subject to corrosion. At the same time, they are well staining. Pre-old rust is finished and covered with metal anti-corrosion compounds: carbolate paste, protective primers based on olifa or epoxy varnish. Then the outer surface is stained with oil paint.

In the bathroom

The small area of \u200b\u200bthe bathroom often leads to the fact that the risers are too close to each other. As a result of the pipe "cry", creating additional damp in and so wet.

Opened laid cold pipes can be painted by any oil paint or enamel. Only heat-resistant enamels are suitable for hot tubes and heated towel rails.

If the crane or shower is dripping, it contributes to the additional cooling of pipes. The heat exchange between them and the environment is enhanced, and the condensate is formed intensively. In addition, water is consumed, which harms ecology and makes the water counters turn. Therefore, maintaining plumbing in good condition will bring tangible savings and benefits.

In the toilet

The need to process pipelines in the toilet is also associated with their close location in space. In addition, the leaking tank leads to a constant movement of cold water through pipes, and this, in turn, to their additional cooling.

Repair of equipment plus thermal insulation and staining will help contain engineering communications in dryness.

Plastic pipes do not rust, but the condensate on them also leads to puddles on the floor and mold on the walls

If the system was initially mounted in a non-optimal way, it will have to pay attention to it, ensuring insulation

Cold water pipes

Universal thermal insulation for plastic "cold" pipes is polystyrene, or simply foam. It does not have elasticity, so insulation is produced in the form of two parts with a deepening for the pipe.

Halves of polystyrene foams wear on the pipeline and fasten with special connecting elements and adhesive adhesive tape

Due to this, the tightness of the isolation is achieved, which is very important to achieve a good effect.

Also used glass gamble or mineral wool. These insulation can be purchased according to the diameter of the pipes or buy a whole roll, which is then used as needed.

With hot water

The complexity is that it cannot be applied to plastic pipes at home. We will have to take care of the purchase of pipes with a corresponding coating with a thickness of 3 cm, made at the factory.

Difference from condensate on pipes

Fighting condensate must be rational

If it did not work out completely get rid of moisture droplets or prevent their appearance in any way, you need to pay attention to other reasons:

• Weather conditions - wet climate and frequent protracted rains, prolonged harsh frost or abundant snowfalls increase the humidity level in the room, and as a result, condensate appears.
• The location of the house near the natural reservoirs, the close grounding of groundwater affects the level of humidity in the room at home.
• Construction disadvantages - not laid a layer of waterproofing foundation, no ventilation, cold floor or raw basement, located under the house.
• Often what is happening a water supply system, the presence of several sources of evaporation (drying of linen, cooking) are also causes of condensate.

Most often, to solve this problem, it is necessary to completely change the internal microclimate of the house, and this requires complex integrated activities, up to overhaul. Each of the situations of the occurrence of condensate requires the study of the causes and individual selection of the method and the method of elimination.

Sometimes events can be simple and economical.

• With excessive moisture, eliminate the source. Use for drying linen only well ventilated premises.
• Equip exhaust ventilation, so that it worked in several modes, including forced.
• Additionally, warming the walls and gender.
• Install air conditioning, with moisture drain function. If there is no such possibility, make the moisture absorber with their own hands.

On the pipes of cold water supply, it is almost always possible to observe the formation of condensate. Such a phenomenon not only spoils the appearance of the bathroom to some extent, but it may cause serious problems. Constantly wet tube elements have a limited life.

Consequently, it is necessary to solve such a problem very quickly. In this case, questions arise that to take in case of detection of water drops on the pipeline and how to remove condensate with cold water pipes. First, you do not need to dramatize the situation too much. Secondly, it is necessary to familiarize themselves with all methods to eliminate this problem. Thirdly, choose the most optimal option and apply it in practice.

Condencators

Since the problem of water condensation is widespread, there are devices that capture water vapor and remove the resulting liquid. In particular, condensate traps are installed at the outlet of the water heaters. Depending on the heat exchange scheme, thermodynamic, thermostatic and mechanical devices are used.

Condencators operating on the float principle of action are most popular. They separate the accumulated water from the steam and remove it from the system, using the difference in the density of water and steam.

Float devices possess the following advantages:

• exceptional reliability;
• high performance;
• optimal energy saving in the system.

How to solve this problem

And she deserves separate attention. You can purchase a special material that can be easily purchased at any construction store for little money.

It does not matter if this was not at hand, you can use sweater. Saving a position can assembling foam and corrugation.

The corrugation is pre-cut into the necessary pieces, and they dress on the nozzles. Empty space is filled with mounting foam. This mission is considered to be completed.

There is another very simple method that will help eliminate the appearance of water droplets on the pipes. To work, you need to prepare:

1. grinding paper;
2. phosphoric acid;
3. thick thread;
4. strips of old fabric;
5. putty knife;
6. acetone.

Procedure:

• Any pieces of unnecessary tissue are cut into strips with a width of no more than 7 cm, which roll up with rolls. They are recommended to harvest with a margin, so as not to be distracted while working.
• The pipe is plastered, otherwise the material is not firmly clung to it. Then they are degreased with acetone.
• At this stage, the rust converter is applied, and when the pipes dry out, they are applied to putty. This material instantly hardens, for this reason, they will have to act quickly.
• The prepared pipes are wrapped with tissue stripes, so that each subsequent coil goes to the previous one. The final coup is tightly tied with a cord.
• Thus, the insulation of the tissue strips is applied by several layers.
• Completes the procedure with an epoxy layer. When it completely dries, the pipe-weather is grinning and put the paint of the selected shade.

Heat insulation

To minimize the effect of temperature drop in cold water pipes and room temperature, you need to insulate them. Excellent thermal insulation, high fire safety, ease of installation, tightness and low price of modern insulation will allow you to evaluate this decision to dignity.

The pipe must be put in a special insulation material - case of foamed polyethylene (energyflow). This flexible material, closed pores of which give it excellent thermal insulation properties.

Your actions:

• dry pipe;
• cut along the energy flow tube;
• wrap a cold water pipe;
• creare longitudinal insulation with glue or clamps;
• glue the energofex ends between themselves;
• optionally, you can paint the insulation of the aerosol paint of the desired color.

Alternatively, preventing the appearance of condensate will help "isollates" - universal material for insulation of pipes, the so-called paint thermos. This is a water-based suspension, which is converted to a polymer coating after drying, which has good thermal insulation properties.