Selection of sectional gates. What garage doors choose

Selection of sectional gates requires studying the characteristics of products offered by manufacturers and accounting for various factors that will affect the operation of structures.

Photo No. 1: Sectional Garage Gate

This article will help you not make a mistake and equip the garage the most suitable model. Having studied the information posted below, you will find answers to all important questions.

What should be the garage in the garage?
What are the advantages and disadvantages of structures that are delivered to the Russian market leading manufacturers?
What size gates to equip a garage?
What sandwich panels are suitable in certain cases?
What needs to be taken into account when choosing drives for automatic designs?
What options for decorative design and color solutions offer manufacturers?

After receiving answers to these questions and useful advice of professionals, you can buy a gate that will serve several decades and will delight the eyes of an attractive appearance during the entire life. You can purchase such products at an affordable price in Moscow.

What are the sectional gates in the garage

Depending on the control method, sectional doors in the garage are manual and automatic.

The first option is the cheapest. However, for opening and closing the sash, you will have to be inside the garage, to independently lead the mechanisms. Manual sectional gates are usually installed with a limited budget, as well as in cases where the places for the installation of power units are not enough.

Constructions with electrical drive are much more convenient in operation. Automatic sectional gates can be controlled both stationary (using wall modules) and remotely (with the help of remote control).

Photo number 2: Sectional garage gates, controlled remotely

If necessary, you can install photocells and configure the system to fully automatically operate. However, this variant of operating the gate is rarely used for security reasons.

How to choose a gate manufacturer in the garage

Sectional garage doors deliver various domestic and foreign manufacturers to the Russian market. Among them: ALUTECH (Belarus), Doorhan (Russia), Hormann (Germany), Torque Force and Flexiforce (Holland), Ryterna (Lithuania) and others.

If you study in detail the characteristics of the sectional gates and the nuances, which are accompanied by the operation of the structures of popular brands (there is a comparative analysis in one of our articles), and also familiarize yourself with the reviews of consumers on the forums, it can be concluded that for use in the middle lane of Russia and in the regions with The harsh climate is better to choose products of the domestic and Belarusian concerns.

You will also find a detailed overview of AlUCH products on our website.

What should be the size of the garage gate

The width of the garage gates is the most important parameter that determines the availability of free space for maneuvers. For one small vehicle, a standard sash (2.5 m) is suitable. In garages intended for several machines or large-sized cars, set the structures with a width of 3-6 m or more.

The height of the gate into the garage is a less significant indicator equal to the height of the opening. To install the design with an electric drive, it is necessary to provide for free space in the ceiling zone.

Image number 1: scheme of sectional garage gates

Formulas for calculating the depth of the walking (W) with various ways to install the structures, you will find in a special article about the size of the sectional gate.

Which profile is better for garage gate

Seaming gate sash consist of sandwich panels. They are made of galvanized sheets, between which the insulation of polyurethane foam or polyester is placed. Decorative coatings are applied to external and inner surfaces.

Image number 2: Sandwich panel in the context

Special traffic jams are used to protect the premises from the penetration of cold air. Thanks to them, the panel is tightly adjacent to each other.

If when choosing a sectional garage gate, you mainly worries the temperature to be maintained in the room, pay attention to the thickness of the sandwich panels.

20 mm. The canvas of this thickness is suitable for installation in unheated garages. "Cold" sectional gates are usually found in parking lots and in underground parking.
35-45 mm. "Warm" panels are best suited for installation in heated garages and auto repair shops. Such gates will maintain an affordable temperature in the premises during the cold season.

To expand the functional, manufacturers equip the canvas with various additional devices and accessories. It can be:

wickets;
window;
side doors;
locks for locking and unlocking drives;
external handles, etc.

Choose additional options depending on the needs and desired appearance.

Photo number 3: Sectional garage doors with gate, windows and an external handle

Manufacturers also offer various options for designer decoration of rods. For example, the Alutech concern produces 6 species of sandwich panels: S-Corrugations, L-Corrugations, M-Corrugations, "Pilenk" and "Microwave". Choose what you like. Specifications of differently decorated panels are identical.

What to choose automation for sectional gates

The choice of automation for section gates mainly depends on the size of the web. For trouble-free operation of the standard sash (2 * 4 m), it will be quite enough to drive with a power of 500 W. To lead large-sized structures in motion, more powerful power units are needed.

Also note the ability to install additional equipment. For example, the antennas will increase the signal reception area from the remote control, and bright lamps operating when driving movement are needed to ensure safety.

Photo cells for automatic opening of the gate, as already mentioned, it is rare, but no one forbits it. This option is relevant if the garage and the adjacent territory are protected and video surveillance.

Image number 3: Type diagram of sectional gates with automation

The most popular automation manufacturers for sectional gates - An-Motors, Nice, Marantec and Came. When choosing systems, first of all, pay attention to the products of these concerns.

Colors of sectional doors

The colors of the sectional gates can be the most different. When choosing a shade, consider how the canvas will be combined with the design of the garage and the facade of the house.

Manufacturers color sectional doors in standard colors from the RAL directory and use original decorative design options. Most interesting decisions are offered by Concerns Alutech and Hormann, but German structures are not popular in Russia due to unjustified high costs.

Image number 4: options for registration of sectional garage doors from AlUCH

Sectional doors will better cope with the assigned tasks and smoothly work the longest possible time if you use the advice of professionals.

Do not save on automation. Purchase only high-quality drives with a long warranty
Do not neglect security requirements. Sectional gates must be equipped with protection systems:

from the fall of the sash when the spring breakdown;
uncontrolled motion of the sandwich panels;
cuts and hooks;
pinching fingers (especially relevant for automatic models).

Order the installation only from professionals. Often, the installation works performed by independently lead to skewers and the rapid output of the structures. Buy sectional garage goal turnkey in a reliable construction company - it means to get a qualitatively installed technique and a guarantee for work performed.

Garage gate | 10.07.2017

The construction of the house is a long and laborious process, at the end of which you want to get a safe, warm and comfortable accommodation. High-quality gates are one of the key elements of providing these characteristics. Alutech has experienced the production of gates and equipment at 21 and knows exactly how to secure the house from the negative impact of the environment, weather conditions and unreasonable guests.

In the article, we will answer the most current issues so that you can make an ideal choice for yourself:

What kind of garage gate is better and what is preferable for the customer?
How many cars will park in the garage and at the entrance to it?
What method of lifting mechanism is most preferable?
What makes the gate canvas make?
How is the installation?
Do you need additional options, or what capabilities does Alutech offer?

Varieties of garage gates, or how not to get lost in sentences

The development of all areas of production made it possible to switch to a new level of parking space. Swing gates - the classic of this sphere, gradually rent their position and inferior the road to more progressive and comfortable designs.

The active development of production allows not only to produce popular models abroad, but also to improve the quality of materials.

At the moment, the Holding "Alutech" produces three types of garage gates:

Sectional;
Roller or rolled;
Swing.

Each type has its advantages that we will tell in detail in the article.

Garage, entrance and number of machinery: Sweeping supplier or necessary information?

The first question of the measurer about the number and size of cars often causes a protest from the customer. But such a key characteristic largely determines the type of garage gate. After all, with a small number of machines and the availability of a wide parking area on the street, you are practically not limited in the choice, but the difficult entrance, the location of the garage on the rise or the low ceilings of the structure significantly narrow the terms of the options.

The measurer when leaving the object will tell about the nuances of the structure and the capabilities of the assembly.

Here is a list of essential obstacles to mounting certain types of doors:

sectionable - not mounted in garages with a proliferation of less than 100 mm for manual control and 120-150 mm for automatic;
sandwich panels are not installed if communications pass under the garage ceiling;
swing - not recommended in rooms with difficult entrance (sharp rise, lack of space before garage);
automatics are rarely rarely installed;
rollent - not used in places with high wind load.

It is because of the technical nuances that is so important to understand and see all the features of your garage.

Features of the entrance and the need for free space

On private possessions, as a rule, there is a place for free entry, but sometimes it happens that the parking is located on a turn or entry directly from the road. Such restrictions deliver inconvenience even the most experienced drivers, and also make it difficult to enter. The choice in favor of sectional or rolling gates will free the entrance from additional obstacles in the form of swinging flaps.

When mounting the swollen gate, the wizard will offer you to decide with the opening method: inside or outward. But with any way you need a lot of free additional space.

For comfortable use of the garage on one passenger car, its minimum size should be 2.5x5 meters. Since the length of the car is an average of 4.5 m, then you have only 0.5 m to close the flaps. In this case, the width of one sash will be 1.25 m.

When choosing an external method of opening sash, you will need a territory for an entrance of 1.5 meters long.

Thus, the presence of a small garage or the absence of space for entry automatically cancels the possibility of mounting the swap design.

At the same time, it is necessary to understand that uneven entrance will make it difficult to build a sectional gate. Tight fit to the floor is the key to high-quality protection against hacking. If your driveway is covered with gravel and there is no flat floor at the indoors itself, then the gate will not be able to guarantee security.

How affect the size of the opening on the design of the gate

The garage for two cars has dimensions, many times different from the standard, so the swollen construction threatens constant problems with the opening. Heavy sash widths from 1.5 meters the owner will have to be opened manually, and if you live in the house year-round, the opening and closing cycle occurs 2-4 times a day at a minimum.

High-quality aluminum rollers are made up to 7 meters long and more. They are light and durable, however, with a strong wind load too wide gates may not withstand.

Alutech rolled portable constructs with a width of more than 7m withstand wind gusts up to 25.5 m / s. Rollers up to 5.5 m long sufficient wind resistant to resist implies at a speed of 37.7 m / s.

The gate from the sandwich panels is good both in a narrow and in a wide variant. The manufacturer releases a panel to 6 m long, and reliable automation easily raises even a heavy cloth.

Height Podolok: What is it, and how is it so important?

The height of the prolok is the distance between the upper edge of the entrance and the ceiling. It is important, since the opening mechanism is attached under the ceiling.

The box with an octogonal shaft does not occupy a lot of space, so it is possible to mount rollers with a minimum height of the sub-combine space.

The height of the sickness for the sectional gate is extremely important, since everything is climbing upstairs:

for a gate area up to 8 m 2, the minimum size of the sizes is 100 mm for manual mechanism and 125 mm for automatic.
for a gate area of \u200b\u200bmore than 8 m 2 of the pertolock, 210 mm should be 210 mm for manual control, 250 mm for automatic.

The width difference Podolok affects the type of balancing springs (torsion takes up more space than stretching springs).

Automatic or manual control: What to choose?

When our specialists ask: "What garage doors better put?", They will no doubt answer: "automatic!". And not only because the Alutech holding cooperates with the best manufacturers of motors, and mainly because to open the garage from the console in the winter and in bad weather is very nice.

Remote control allows the driver to open the garage without leaving the steering wheel.

A qualitatively new parking level provides an automatic opening system. You do not have to raise a heavy cloth every time or get out of the rain car, for check-in to the covered room it will only be necessary to press the button on the remote. In addition, the automatic wire can be supplemented with accessories that will perform exploitation even more convenient:

photocells, optosensors, warning lamps will ensure user security;
digital switches, contactless reading devices will limit unauthorized access;
radio control offers ample opportunities for the user.

"Alutech" is working daily on improving the efficiency of products. All gates are equipped:

system against pinching fingers;
sensitive edge to protect against closing at a person by road or vehicle.

Put electronics on the garage doors can be at any time. If you are constrained in the means now, automate them after a while.

What role does the size of the opening play?

Not so much the possibility of car free passage depends on the width and height, how much the ability to build a particular design. After all, the more open, the more the weight of the canvas.

Automation depends on weight, the motors are designed for certain size and weight of the canvas.

For section gates:

an-Motors drives are designed for a cloth of up to 8.4 - 16 m 2, depending on the model;
Marantec manufactures motors designed to 7.5 - 15 m 2, depending on the series and model;
ComNello produces technique capable of lifting the cloth with an area of \u200b\u200bup to 8.4 - 16 m 2.

Automation for rolling systems is available on AlUCH's own production. Differences in power are associated with the diameter of the shaft, to which the canvas is screwed.

Swing gates are mounted only with manual control due to technical problems when opening. Therefore, more and more users go to lifting mechanisms.

The canvas: from which they are made, how to protect and fasten

The cloth section gate is assembled from high-strength sandwich panels. A high-quality three-layer coating can protect the steel surface not only from corrosion, but also from mechanical damage.

Studies show that such a coating is able to withstand 15 years of exploitation in the coastal marine zone. Such results of the company's masters have achieved due to the use of the primer layer (10-15 μm), zinc coating (16 μm) and a new polyurethane coating with modified polyamide particles with a thickness of 20-25 μm.

"Alutech" produces 2 series of sectional systems:

"Trend" series;
series "Classic".

They differ in thickness and, accordingly, the parameters of thermal insulation.

The "Trend" series is a 40 mm thick sandwich panels filled with polyurethane foam. The special fastening system in the "lock" using 4 self-samples eliminates the separation of panels over time. At the same time, the company has implemented a security system to protect against pinching fingers, cuts and a hook.

Own production helps to embody all the desires of the client into reality. Alutech offers an assortment of 5 patterns of the canvas and 10 colors, while the width and length of the sandwich panel can be selected in 5 mm increments.

The "Classic" series is characterized by increased thermal insulation properties due to the thickness of the panels in 45 mm. Such panels on thermal protection are identical to a brick wall with a thickness of 60 mm.

All materials for rolling gates are manufactured in their own production "Alutech". This advantage allows not only to control the process, but also in time to introduce new developments.

In 2006, the holding began to use rolling lines, for the release of elements without damage to the steel coating.

Thanks to continuous improvement, rollers are not subject to corrosion and have a special strength to abrasion. The filling aluminum ribbon is covered with two polyurethane paint layers, which provides long protection against burnout, chipping and scratches.

A wide range of colors will delight aesthetes. 16 basic colors will allow you to choose the perfect option for your home.

Installation: Hire professionals?

The gate from the sandwich panels are collected at the facility. A complete set of pieces in a disassembled form comes to the customer. The assembly scheme is simple, but we advise you to hire professionals.

Professional assembly is a guarantee of durability and security. Installation specialists know exactly how elements of the design are fastened and errors will not allow.

Also, you can order a service "Preparation of the opening" or align it yourself. The measurer will indicate the shortcomings of the entry at the time of the order.

For installation of sectional doors, work is needed to align the opening.

The manufacturer "Alutech" offers 10 types of installation depending on the width of the pods and the roof configuration:

standard - the canvas rises with an angle of 90 degrees above the upper edge of the opening, the shaft is located in the bend place;
low - the shaft is located at the end of the design;
inclined (high and low, with the bottom and top arrangement of the shaft) - panels go up under the tilt of 30 degrees, the shaft is located in the bend (top location) or below the bend (lower);
high (with the bottom and upper arrangement of the shaft) - the canvas first rises along the entire length of the perts, and then bends and goes under the ceiling. This method of installation exempts the sub-standard space;
vertical (with the lower and upper arrangement of the shaft) - more suitable for industrial premises. The canvas goes vertically up, differently is called a guillotine way.

Installation of the rolling gate is concluded in the assembly of the guide and fastening the shaft. The placement of the shaft outdoor requires the mandatory presence of a protective box to prevent corrosion of the mechanism. An open installation of the mechanism is possible indoors.

The process of installing swing gates is simple. The product is delivered to the object in the assembly, you only need to attach the doors using three sturges.

The advantage of the gate "Alutech" in a wide range of options

The manufacturer of Alutech takes care of its customers, so offers a wide range of additional options:

wicket (built-in and separate);
windows and ventilation holes;
castle and drive unlocking mechanism.

To select the desired options and accessories you need to learn about them more.

Gate - Easy access to the garage

For mortise wickets, it is possible to choose one of the three threshold options:

flat (18-20 mm) ensures the simplicity of entry of wheelchairs and bicycles;
low (100 mm) meets all fire safety rules;
high (145 mm) - on cloths of large sizes.

Built-in gate is a comfortable entrance to the garage for guests and owners. At the same time, it does not waste the design. A narrow framing asks the joints and gives the gate an aristocratic view.

The sash position sensor will not enable the lifting mechanism if the built-in wicket is open or looked closely.

If you can put the built-in gate, we suggest paying attention to the side door. The manufacturer makes it from the panels that are harmony with the main web.

Installation of mortise wickets on rollers is impossible in view of the technical characteristics.

Sectional Gate Accessories

Caring for your property is one of the main tasks of a person. What to ensure not only the protection of the room, but the convenience of using "Alutech" offers to establish additional options:

windows will provide room light;
ventilation holes will help the implementation of a natural air exchange;
the electric drive unlocking mechanism is a manual mode system when the electricity is disconnected;

The cable length of the unlocking mechanism is 4500 mm. Pay attention to this when ordering a large linen.

castle - Additional security guarantee for your home, will also help translate the opening system in manual mode.

Rolled gates open up wide opportunities for the user. Ventilation and viewing rollers provide lighting and ventilation not worse than specialized holes in the sandwich panels. Extruded profiles are available in 12 colors, pay attention to this when choosing.

How to make a choice among the proposed diversity

If you are lost in choosing colors, series and drawings, exhale. We will offer the option suitable for you. We try to do everything possible so that customers are satisfied with the products produced in the Alutech factory.

Still doubt? Check out customer reviews to finally decide on the choice.

The insulation of the car from external climatic influences depends on the peculiarities of the garage, the foundation and roof. An important role in this plays the right choice of garage gates, since their quality and functionality affect the microclimate indoors and favorable conditions for parts and parts of the car. This element of the garage is given special attention due to its permanent use, so the question of which type of design is relevant to this day.

What are the types of garage gates

To date, there are several of their main species:

Lifting-section.
Rolled (roller).
Rotary lifting.
Two bivalve swollen.

Each of these species have their own nuances, which in one way or another satisfies the needs of car owners. You can create additional convenience and equip the gates with lifting or sliding mechanisms that are provided for installation for each type. To understand the principles of use, the correct installation, the functionality and features of this list of species, you need to deal with each of them.

Lifting-section

These gates have a form of design from metal shields connected to a single web using special loops. A solid sash of several panels is easily shifted up due to the lifting mechanism, fixed to the walls and ceiling of the room. Smooth opening of these gates provide bearings and rubberized rollers on the connecting elements of the panels. With these parts, the sash gently moves along the metal guide.

Lifting and sectional gates in the garage - solid and heavy design

In the open position, the sash is horizontally under the ceiling. To provide additional comfort when using the garage gate of this species, they are equipped with automatic drives that are two types:

The torsion system of the garage gate lift has gained wide popularity among private garages owners. It is a drive fixed to the central region of the ceiling at a distance of several meters from the reception. The system connects the gate section and the drive using a cable and traction lever.
The bulk drive is often used for the gate of industrial enterprises, it is more powerful than the previous system, and is designed specifically for a massive gate. The bulk type has a view of an electric motor that is attached to the garage outlook near the shaft. Mechanisms raise the gate sections using the power effect of the shaft. The engine is equipped with a special chain that allows you to control the gate when the electricity is turned off.

Both types can be equipped with special remote control devices.

The lifting-section type of the gate has a number of positive and negative qualities. The advantages include the following criteria:

The design saves a place. Thanks to the location in the open state of the sash under the ceiling, the gate does not occupy space both indoors and outside.
Large deadlines and thermal insulation properties of the material. The use of sandwich panels in the production of the sections of the gate provides reliability of the entire canvas. The use of modern technologies when creating them gives a reliable heat insulating effect.
Good sound insulation. This quality is achieved by using sandwich panels.
Universal application. The design allows the installation of a mechanism on the outs of various magnitude. Therefore, sectional doors are convenient and in industrial use, and for home options.
The gate is relatively resistant to deformation and mechanical damage.

Depending on the type of roof of the garage, the types of lifting on the gate differ

The following criteria are treated as negative sides:

Departure sash requires an additional place to install it. Therefore, the length of the garage should be one and a half times greater than the width of the room of the room.
The cost of the lifting-sectional gate of the average size (height 2 m, width 3 m), will be about 60-70 thousand rubles.
Sectional doors require permanent maintenance, as they consist of numerous parts, elements and mechanisms that are constantly acting.
Low resistance to hacking. The gate of this species is advisable to install only in the protected area.

Rolled (roller)

This type of gate has such a name thanks to the method of placement at the time of opening and closing. They consist of several main elements:

Separate profile stripes (lamellas) connected to a solid canvas.
The mechanism that moves the closing surface.
Two guide profiles holding a canvas.
A special lever that unlocks the design in case of turning off the electricity.
The shaft on which the canvas is screwed.

The whole design has a flexible surface, which allows it to fit into a small box. Its installation can be carried out in several ways:

with placement indoors;
outside;
false way inside the garage;
overhead - outward.

Options for structural solutions of rolling gates will come to taste to many car owners

Rolled and rolling structures are made of aluminum and steel. Both gates are equipped with a special system with a mechanical lift in case of emergency.

For steel structures, the maximum dimensions of the gate are provided: width - up to 7 meters, an area of \u200b\u200bnot more than 49 m 2. The canvas is assembled from steel galvanized profiles with a thickness of up to 0.8 mm. The blasting box is installed if its area is not more than 11 m 2.

For aluminum structures, the maximum permissible dimensions have limits: width up to 6 meters at an area up to 14 m 2. Such a gate is made of aluminum profile: extruded or filled with special foam.

This type of gate is convenient to apply to close large outlook, where you need saving free space. They found wide use when installed in garages, warehouses, outlets and as partitions in banks and office space.

Rolled structures have a number of advantages that are expressed as follows:

Compact design when used. During closing and opening, the canvas does not protrude beyond the walls, but moves up and down parallel to it.
Easy installation design.
The ability to operate equipment automatic control.
Low cost.
Beautiful appearance.
Reliably protect against dust and foreign sounds.
Durability of the use of construction.

Rolled structures are light and compact, but anti-vandal functions have hardly

The disadvantages of the rolled gate include:

These gates will not protect the property from hacking, so they are better to install them if there is additional security.
They will not suit if there was a need to preserve heat in the room. There are many gaps and cracks in the design.
With prolonged low temperatures, the elements of the gate can be covered with ice, which affects the normal operation of the device.

Pottime lifting

The gate of this species is a one-piece shield covering the entire outlet of the garage. Thanks to the installed metal frame, the sash can be placed parallel under the ceiling, 90 degrees from the initial position.

The frame frame is the main detail of the gate, so it is made of steel. From the same metal make the gate. For ease of use, they are equipped with an electric drive. This makes it possible to manage them without leaving the car.

Although it is a more reliable structure than previous options, but, like everyone else, it has its own positive and negative properties.

The advantages include the following criteria:

One piece will ensure reliable protection against penetration and hacking.
The material of the manufacture of this type of gate is stainless steel, which will reliably retain the car from the effects of natural precipitation.
The gate in the open position does not occupy the place and space indoors.
The design of a solid sash is that it is easy to insulate the polystyrene foam or to re-organize other lightweight materials.
Ability to use automatic systems.

It is better if there will be one or two cars in the garage, which do not often go beyond the house

The minuses of the lifting and rotary garage doors include:

Mount this gate can only be rectangular.
When installing, it is necessary to consider that the fully mounted gate will reduce the height of the outlet from 20 to 30 cm.
If there is no damage to any area of \u200b\u200bsash, it is impossible to repair it. Replacing the entire shield of the gate.
For insulation, you need to pick up materials with lightweight weight. If this material is heavy, you should equip the counterweight design.
For these gates recommended limited application. More than ten times a day, they should not use.
This type of gate is more suitable for a cold garage due to the complexity of the insulation of the joints.

Two bivalve swollen

This type of gate was and remains the most popular due to its cost and reliability. Swing mechanisms are two capital sash attached to the hinges to rigid racks. For the structural strength, the racks are made as a solid metal strapping. The flaps do in such a way that they can open both outside and inside the garage - it depends on the desire of the owner. For convenience in one of the flaps, the wicket is equipped.

Bivalve swollen gates are most suitable for creating a warm garage.

These gates have several advantages and disadvantages compared to other species. The pluses include the following:

The cost of this design is much lower than previous species.
Swing gates can be mounted in a limited space.
It is possible to establish an electric drive.
The gate can be effectively insulated with various materials.

Such a gate is easiest to insulate and, if necessary, repair with your own hands

The disadvantages of the swollen gate include a number of the following criteria:

The design of the gate is obsolete.
Periodic check of loops and gate frames. Over time, the flaps can sign and touch the earth. It may also cause further malfunction of the automatic drive.
The life of this type of gate is less than that of others, due to the loads on the loop and the frame with the open position of the sash.
Before the garage is required to open the sash.

Folding

The design of this type of gate is made of vertical sections made of aluminum alloys. In the open state, these connected flaps resemble the collected score. Folding gates are used in hangar, garages and large warehouses.

These gates have their own positive features:

Folding gates can be installed in any garage, regardless of its height and width.
The design of vertical sections can be fastened from either side of the day, as well as at the top or bottom.
Acceptable prices.
Easy to repair and replace the sections.

In appearance, folding gates are more similar to decorative than on functional structures

The disadvantages of this design include:

The sash of such gates is rapidly wear out.
Do not protect against hacking and penetration.

Examples of varieties in the photo

Allow you to leave the opening partially open outdoor option of fastening the box when opening you need a small space for the movement of the sash teddown by the wicket will save heat in the cold months of the construct eases. Comfortable use

Tips for the choice of gates in the garage: how not to be mistaken when buying

Among the many species and designs can be easily mistaken in the choice of a suitable option. That this does not happen to take into account the following points:

During the acquisition, you need to make sure the polymer material, which is covered by the gate. Methods play an important role, with the help of the galvanizing of parts, as it is directly related to durability. The correct way of galvanizing will be powder spraying.
When selecting panels, you must choose them with high-quality polyurethane filler. Otherwise, in a few years, it will begin to settle down, which will lead to the loss of thermal insulation properties of the web.
Special attention should be paid to the joints, since in these places there should be details and elements only from a high-quality and wear-resistant polymer.
It will be useful to learn about additional strengthening elements.
When buying, you need to consider the fact that torsion springs are equipped with blocking mechanisms. It will ensure your safety during the gate breakage: the mechanisms will not allow falling the sash, but will block it.
If the design of the gate will be installed in the place where the wet climate prevails, then it is necessary to choose a material protected by an anti-corrosion layer.
It is also worth clarifying the searches for the service and the possibility of design equipment with additional protection systems for penetration and hacking.
If the garage does not have an additional side door, you need to select the option of the gate with the gate.
If the electric drive is purchased, then you need to pay attention to the presence of traction belts. Different firms can use for this chain or cable. The situation with the belt is more convenient, since in this case there is no need to lubricate it.
When choosing an electric drive, make sure that it is equipped with an automatic lock. This will be useful in case of falling under the sash of the foreign object.
To reduce the load during the lowering of the sash, the electric drive must be equipped with a device that slows the speed.

Most Popular Garage Design Manufacturers

To be confident as an acquired gate, you need to give preference to positively proven firms. The main companies are:

"Hurman" (Germany). This company supplies garage equipment that meets international certificates with a warranty period of 10 years.
"Dorhan" (Russia). The company specializes in the manufacture of component parts and elements for all types of garage gates.
"Alutech" (Belarus). The leading manufacturer of profile systems from aluminum and sectional, swing, roll-out, rolling gates and automation.

Convenience when using garage gates is ensured by automatic drive systems. Equipment by these devices increases the cost of the garage gate, but makes them more comfortable. Choosing these systems, you need to navigate the leading manufacturers:

Nice, Faac, Came (Italy) or Chinese An-Motors.
Novoferm (Germany).
Bremet (Italy).
Normstahl (Germany, Switzerland).
Meswa (Finland).
Clopay (USA).
Ryterna (Latvia).

From Russian manufacturers it is worth highlighting:

Technoprof.
"Erin".
Rolclassic.

Sectional gates are installed in garages, parkings and other rooms for overlapping opening. All gates are similar design. Sections between themselves are connected by loops. At the edges of the opening, the guide tires are installed in which the rollers of brackets are inserted. Tires can be installed vertically (indoors with very high ceilings) or start under the ceiling. When picked up the rollers, the rollers are almost silently moving along the guides, carried away the carrier cloth under the ceiling. Equilibrium of the canvas is maintained by springs of stretching or torsion type.

Before purchasing your favorite model from one of the major manufacturers, it is important to make a choice of not only the canvas itself, but also to choose high-quality accessories, an electric drive, to think over additional options in advance that will be necessary for comfortable operation, such as a garage.

What qualities should modern sectional doors have?

Important positive sides of the sectional gates are high reliability of the design, ease of use, saving free space space and maximum energy efficiency.

For example, the sectional gates of AlUCH production, thanks to a wide range of sizes, are suitable for installation in any types of openings, regardless of the climatic conditions of the terrain, the material of the walls and internal architecture, protect the most qualitatively from the penetration of intruders, they have good thermal insulation indicators, and also advantageously emphasize the modern finish facade.

Energy efficiency of the sectional gate - how to save money?

It is achieved through the use of high-quality insulation and seals in the design of the sandwich panels. For insulation, polyurethane foam is usually used. The thermal insulation material is placed between the two aluminum sheets or galvanized steel. Application by producer of polyurethane foam of increased density, namely, 46-47 kg / m 3, it allows you to further increase the durability of the gate to the deformation.

On a note! The quality of the sectional gates is regulated by GOST "Metal Gate" 31174-2003.

The design of the sandwich panels and the thickness of the canvas

Sectional doors can be with varying degrees of energy efficiency. For example, a cloth with a thickness of 9 to 20 mm is unacceptable for mounting in open spaces of heated rooms. Low indicators of heat resistant are permissible in such premises as unheated warehouses, underground parking and parking. For heated premises, it is better to choose a cloth with a thickness of 45 mm.

On a note! If you need to install the gate in the room where natural light is required, it is worth stopping the choice on panoramic models. Sections are made of aluminum profiles. There is a special series of panoramic gates made from a profile with a thermal survey. Also, the panoramic gates can be made of a combination of sandwich panels and translucent inserts or completely from transparent material, edged with aluminum profiles (one of the best options for car dealerships and exhibition centers).

Consider the design of the insulated portable canvase on the example of the "Alutech" gate.

At the gate "Alutech" a unique design of sections. The thickness of each sandwich section of the "Classic" series is 45 mm, which is 5-25 mm more than the thickness of the collar sections of other manufacturers.

There is a polyurethane foam insulation between two outer walls from high-quality galvanized steel. During operation, the possibility of separation of sections is completely eliminated due to the maximum strong castle compound of steel sheets. A closed circuit without deformations withstands both sharp temperature differences and random blows of great strength, including sharp deposition of the gate.

Sectional doors "Alutech" is a design that provides reliable protection for the inner room of the garage, even from the harsh frosts and wind gusts up to 120 m / s, which corresponds to the load of 700 Pa. Such data were obtained after the studies conducted.

As an additional insulation of the panel, equipped with two-fledged polymer EPDM seals that exclude "cold bridges". On the perimeter of the gate is also mounted seals made on the basis of polymer rubber. The material of the seals remains elastic even at negative temperatures, which is extremely important for regions with a cold climate.

A dense adjoining to the impeller and the complete absence of the slightest drafts is provided by adjustable roller brackets. As a result, a significant savings on the heating of the premises due to the high heat-saving properties of the sectional gate.

Prices for sectional doors

sectional doors

Important! , pay attention to their compliance with the European standard EN12604 from 2000. A safe design, made in accordance with the standard, has protection against pinching the fingers and the falling of the portal canvas in the event of a cable break, the protection system of springs. A mustard canvas weighs at least 100 kg, better to protect yourself from accidents in advance.

Comparison of sectional gates with construction materials of different thickness

If you compare the "garage classic", that is, the standard steel swollen gates and sectional, then the first is significantly won in price. But this is only at first glance. Outdated design is not an obstacle for dust, moisture, frost, noise from the street. From all of these adverse effects, only sectional gates will protect the best way. Modern automation with estimates paying for the funds spent by providing a proper level of comfort for users.

Sections 45 mm thick in heat resistant indicators are comparable with red brick masonry with a thickness of 0.6 m.

How much electricity is spent?

It is worth noting a direct connection between the size of the gate and the power of the engine, which leads to a movement mechanism of raising / lowering the gate. Than the gate is more, the more powerful engine. Usually choose a power of 0.2-0.5 kW. But in the case of installing the most powerful engine, electricity consumption is extremely small, the amount of the monthly fee will increase quite slightly. Of course, you can do without automation at all, but in rainy weather it is much more pleasant to open the gate with a remote control, sitting in your own car.

On a note! Choosing a gate with automation, check the manufacturer's presence of a gate lock function when lowering if an obstacle is obstacle under the web.

If an obstacle is immediately blocked under the godlight

How to choose the size of the gate?

Measure the dimming dimensions and order the most suitable canvas. Typically, the gate is made individually for each client, step in width and height at least 5 mm.

The maximum standard dimensions of the gate equipped with stretching springs - 3.5 x 3,085 m. For a gate with torsion springs, this figure is 6 x 3,085 m. Some manufacturers to order are made by a web width only to 5 meters.

To make the design and installed without errors, it is important to comply with a number of requirements:

Find out by studying the instructions in a special article on our portal.

Texture and shades

Coloring the gate can imitate the pattern of natural wood or be any other, according to the RAL catalog, but on the application of decorative coverage, the manufacturer requires an additional time. If the deadlines are pressed, then without allowing to the price you can buy a canvas, painted into one of the standard colors, which are offered by manufacturers: white, red, silver, anthracite, ivory shade, etc.

The structure of the surface of the sections to the choice is either smooth or with the imitation of the tree (embossed).

The canvas produced in five different design solutions, namely:

S-corrugation;
M-corrugation;
L-corrugation;
with the relief "Pilenka" and "Microwave".

From such a variety is easy to choose the design as possible under the style of the building.

Furnitura

For example, in the standard basic bundle of the "Alutech Classic" goes high-grade stainless steel fittings. Stainless roller brackets and intermediate loops are supplied without surcharge to the total value of the gate. It is especially important to pay attention to the material manufacturing material to those who plan to install the gate in the climate with high humidity. The combination of air flow and high humidity leads to a rapid appearance of corrosion, this not only spoils the appearance of the design, but also may cause a reduction in its life, quick failure.

If rollers are equipped rolling ball bearingsThis guarantees a long service life and low noise when moving the gate. If the gate is not equipped with rolling bearings, when lifting and lowering the gate will be made of unpleasant noise.

The newest development of "Alutech" - cables with polymer core. Cable diameters: 3, 4, 5 mm. The core provides additional wear resistance due to flexibility. The service life of the gate increases significantly. If the mass of the portal cloth is more than 450 kg or the gate will be operated in high humidity, it is worth a preference to stainless steel cables.

Residents of regions with hot climate and / or high wind loads should pay attention to such an element of the gate as strinking profiles. The profiles horizontally fixed on sections significantly reduce the risk of web deformations by adding rigidity and maximum stability.

Read how, having familiarized yourself with the step-by-step algorithm from "Alutech".

Additional elements for functional expansion

Each buyer may supplement the gate design at its discretion, so that use has become even more comfortable. One of these additional elements is gate.

Gate Opening only outside and can be equipped with linear closers, mounted position sensors, visors to protect against rain, anti-vandal metal handles, devices for eliminating saflifs. The wicket can be with a flat threshold (height 20 m), high or standard version (145 and 100 mm, respectively). From the fall of dust inside the room reliably protect the double brush installed in the bottom section of the wicket.

"Smart" Automation will not allow you to open the gate if the door wicket will be open. This ensures additional safety and reliability of the entire design as a whole.

The gate allows you to save the resources of the sectional gate (each factory structure has a certain margin of strength expressed in a guaranteed number of lifts and lowering of the sash). If it is necessary to just get inside the garage, it is not necessary to move the lifting mechanism of the gate. Thus, electricity is not only saved, but also heat remains indoors.

The framing of the wicket is usually offered in two shades: silver and gray. However, you can always order staining in your favorite color.

Do not like wicket? Burly install side door. The entrance design is mounted in a separate opening near the gate. Profitable doors:

mounting type varieties;
wide color palette of doors, boxes, accessories;
the ability to supplement the door to the canvas classic or panoramic windows, closer, ventilation grids.

Tandem gates and doors will complement and decorate the facade of the building.

On a note! It is worth purchasing the gate and the door from one manufacturer. Otherwise, the surfaces of the structures may vary on the shade and texture, poorly harmony and unprofitably standing out on the overall design of the facade.

In the classic version of the sectional canvas deaf, but if it is necessary to reduce the cost of lighting the garage during the daytime, then you should choose gate with windows.

So, for example, the company "Alutech" offers round (diameter 322 mm), square (322x322 mm) and rectangular (522x322 mm) windows with acrylic single-chamber double-glazed windows with a thickness of 18 mm.

Additional decorative elements for rectangular windows:

set of "Dawn" inserts;
insert "Direct Cross".

Window frames and inserts are made of white and brown shades.

Prices for gate

Petal cloth and an additional door are equipped with windows. To decorate the insertion "Dawn"

Do not forget about the castles. An element that is often included in the basic configuration - savka.. Actually in the presence of an additional entrance to the garage, since the valve can be closed and open only from the inside of the room.

Castle "Antipanika" For the gate, it will allow to open it from the inside by simply pressing the handle, even if the castle was closed outside the turn.

To open and close the gate, being on the street, it is better to choose barbed type lock or install automation set. For example, the ALUTECH AN-Motors ASG series automatics will cost 9360 - 10,490 rubles.

Modern automation works even at a temperature of minus 20 degrees.

If frequent power supply interruptions are observed in the region, it is recommended to install external unlocking electric drive (for example, "Alutech" offers a set of unlocking mechanism as an additional option for only 915 rubles). Having established this element, one can be completely sure that the gate will not be blocked at regular interruptions of electricity. However, if there is an additional entrance to the garage, then open the gate will be easily from the inside.

What makes it possible to increase the durability of the gate?

How to choose, the decorative coating of which will remain in primeval form even a few years later?

First of all, pay attention to the quality of the steel sheets themselves, of which the gate is manufactured. Best corrosion protection is zinc coating Thickness of at least 16 micrometers (consumption 225 g / m 2).

The quality of the paint coating also plays the quality of the paint and varnish. Whatever the shade was not chosen, you need to be completely confident not only in its saturation, but also quality. "Alutech" is the only company that uses polyurethane coating, modified by polyamide particles (PUR-PA)Effectively resists mechanical impacts, moisture and chemicals, protects against corrosion, therefore, the decorative properties of the gate are preserved the entire period of operation of the structure. The recommended coating layer thickness is 25-35 micrometers, the thickness of the primer layer is 5-7 microns. With such protection, you just do not have to spend money on repairs.

A polyurethane coating modified by polyamide particles is applied on the front side of the Ayutech panel

Find out, and also familiarize yourself with the Overview of the options, in a special article on our portal.

How else to protect the gate from corrosion

Right choice - use of hardware with multi-layer composite anti-corrosion coating. Roller brackets are attached to the roller brackets to the cloth. But for regions with high humidity, methols from stainless steel are still relevant. From the same material should be made axis of the rollers, be sure to pay attention to it.

Guides also need to protect against rust. Profiles must be made of galvanized steel and covered with powder paint.

Prices for methies

Even the highest quality gates need care. Timely application of lubricant, for example, Litol 24 will extend the service life of metal elements, such as springs, roller axis and brackets.