The entrance door does not make an upholstery or having an old cracking surface looks extremely inaccier, forming in advance with the negative idea of \u200b\u200bthe owners of housing. Moreover, she does not retain heat inside the apartment, and all the noise from the entrance freely penetrates the room. Therefore, over time, any good owner has a desire to put in order both from the aesthetic and practical side.

Help the door of the skin with his own hands, while solving the problems of insulation and noise insulation - it is quite possible, so this event does not apply to the work of a high degree of complexity, and is accessible to almost everyone. The main thing is to have all the necessary materials, certain tools and look good in the sequence of work.

Preparation for the upholstery of the door

1. To update the door upholstery, you will need to prepare the following materials:

• Genuine leather, of course, the material is very expensive, and is used for these purposes in exceptional cases. Not trouble, there is artificial leather (leatherette or dermatin). This material is available in a large assortment in building stores, and varies in color, thickness and texture pattern, so it can be chosen for every taste. High-quality artificial leather and visually, and relatively differs from natural.

The width of this material varies from 1100 to 1400 mm, and this is quite enough for the size of any door canvase. Before purchasing the leatherette, you need to measure the height of the door and add to the resulting result of 25-30 cm. Such a length of the upholstery material must be bought for one side.

It should also be forgotten that the upholstery material will be needed for the manufacture of rollers, which will be fixed around the perimeter of the door canvas. For them, they will need three strips having a width of 12-15 cm and a length that is smoomed by the height of the door.

• For sound insulation and insulation, a sheet porolon is suitable, dense syntheps or felt. The required thickness of the material is from 10 to 25 mm.

As a heater, you can use felt ...

This value will depend on the type of material, and on the desired volume of the drawing, if it is supposed to be done with decorative nails, thin wire or fishing line.

... or foam rubber sheets

• Wallpaper nails with a decorative cap. They can be made of alloys of copper, silver or gold shade, or have a tight material of the same color as the chosen upholstery material.

Wallpaper cloves - you can choose the most suitable for design

The diameter of Zhl Yapper or their design will depend on the design solution for the design of the doorway.

In order for the common look to Veri, it looks harmonious, it is best to pick up nails under the color handle color and castle.

• If a metal door is put in order, one of the high-resistant polymer adhesives is purchased for this, for example, "88" or a universal "moment."
• In addition to the leaf insulation, the bands of the round insulation (foam or foamed polyethylene) will be needed, which are sold by a meter. For our purposes, a diameter of 10, 15 or 20 mm is suitable.

2. From the tools should be prepared:

• Staples and staplers for temporary fixation of the insulation and upholstery material. The most convenient size of the bracket for the upholstery of the door is 8 ÷ 10 mm.
• The average size of the hammer to climb decorative nails.
• A sharp construction knife - it is useful for cutting the insulation and upholstery material.
• A screwdriver with a set of nozzles (bit) and a massive screwdriver - they will be useful to dismantle the old sheathing, removal and subsequent installation of locks and sights.
• Nail-holder and pliers are needed to pull out nails, if a They will go wrong when driving and, necessarily to dismantle the old coating, in the case when it was established.
• Scissors for cutting materials.

3. To preparatory work, you can attribute to the removal of old door upholstery:

• All are dismantled all removable elements - eye, locks and door handles.
• Next, with the help of tools, the old sheathing is removed as much as possible. It can be picked up with a powerful screwdriver, and then pliers. Usually, if the materials are not planted for glue, dermatin and the insulation separated from the door canvase enough. When removing the upholstery with an old wooden door, excessive effort should not be used to damage the cloth. Be sure to carefully examine the entire surface to remove the remaining unnecessary nails, brackets, self-tapping screws, fragments of the old coating
• After cleaning the surface, the door can be removed from the loops and is laid on the prepared desktop (workbench) or the installed four-six stools. Further overwhelming work can be carried out in this position. If solved the web with the loops to remove, then before this process you need to mention its outline on the door frame.
• Sometimes the door is not removed, and its cover is carried out in a suspended state at her regular place.

Prices for various types of upholstery

Upholstery

How to hide the door of the skin with your own hands - various options

To disassemble all the technology on the trim from all sides in detail, you need to consider three different options of work - this is the upholstery of the outside of the wooden door, then internal, and then stop on the features of a similar process on the metal door.

Wooden door - internal upholstery

For the long-established practice, wooden entrance doors in high-rise buildings were opened by the apartment. It is this option that will be considered.

The inner covering of the door opened in the apartment is somewhat different from the outdoor upholstery, and the main difference of this process is to apply additional insulation elements - Valikov. They are made of upholstered material and sliced \u200b\u200binsulation. It is convenient to use ready-made rollers from foamed polyethylene as a warming gasket, which are sold. This element of the overall design serves to reliably close the slots between the door and the door frame. Therefore, they are nourished with such a calculation so that they act beyond the door of 10 ÷ 20 mm. It must be remembered that from the other side where the loops are located, the roller to the robbed in such a way that it completely closes the slot over the entire height of the door jamb.

• The first stage of work is cutting up the upholstered material and insulation. For the first, the exact geometric parameters of the door are taken to which 120-150 mm is added - this will become the size that needs for decorative sheathing of the web.

As a rule, strips of trimming always remain - they are perfect for the formation of sealing rollers for the upholstery of the contour.

The insulation canvas must have a size of 10 mm m nisha on each side than the door itself.

• On the perimeter of the door with the brackets with the help of a stapler, the leatherette strips of the front surface down are attached. Typically use strips up to 140 mm wide, length exactly in size of the door dense. At the same time, there are about 40 mm of this strip on the door surface - the rest should be outside.

In these strips, insulating tapes of foam rubber Polyeneetylene are wrapped. Thus, rollers are formed, which the staplers are also fixed on the door canvase.

Installation of rollers start from the right upper corner of the door, then the vertical edges of the door are fixed, and only then - to the bottom. At the same time, the location of the door is taken into account relative to the floor - the roller should not be thrown about the floor covering, since it is very quickly causing and breaking.

If an invoice is assumed, it is taken into account when attaching rollers - the corresponding gap is made.

• Next, insulating material is laid on the door leaf. It is fixed around the perimeter using a bracket by retreating from its edge by 5-7 cm. Holes for sight glaze and locks are immediately cut in it.

• The next step is to fasten on the surface, on top of the insulation, the most upholstered material - artificial leather.

It wraps over the edges of the insulation and fixes along the upper corners with the help of a bracket. If the upholstery is planned with a special drawing, then its markup is performed on the material fixed above.

If the leatherette must be fixed only around the perimeter, then decorative nails are clogged at the same distance from each other in 60 ÷ 80 mm. The material along the feeding is stretched, because after completing the work, it must be perfectly even.

Find out the top 10 doors from our new article -

Hard door

The outer upholstery of the door, which opens the apartment, is as follows:

• Previously, with a closed position with a pencil on the doorway, a rectangle of the door frame is delineated - this line will show, at what distance from the edge must be installed upholstery. The remaining distance will be necessary for a "quarter" selected in the door jamb.
• The next step is fixed with a thermal material with a retreat from the drawn line inside one centimeter.
• Then the main material of the casing with an outlined line is nourished tind His edge in In the nuclei, similar to the inner installation, but the bottom edge of the material is still free.

Characteristic feature - sealing rollers are not attached to the door leaf, but on the box

• From the outside, the insulation roller is installed on three sides, on the door, but on the rack and crossbar of the door jammer, except the bottom side. To peel a similar roller to the threshold - absolutely meaningless, since it will not fulfill its functions, besides, it will quickly break off or erased from constant contact with footwear passing through the door of people.

The dermatine band is fixed by the front side of the stapler jacket, it is installed in the insulation strip, the second face of the material is refilled inward, forming a roller, and is nailed with decorative nails. The roller should be on the door when it is closed at 15 - 20 mm, but you need to trace so that it does not come to the keyhole.

• The lower insulation can not be too voluminous, it is attached to the door leaf itself and must fit tightly to the threshold.
• Further, the main roller is stretched and the main fabric is nailed.
• The last stage, after the upholstery of both sides, all the doorways are installed accessories - Eyeball, handles and locks. It is very important to accurately make small cuts on the trim. The main thing is not to cut the material more than it is required, otherwise the door will immediately lose a respectable look.

Video: Wooden entrance door upholstery

Prices for entrance doors

Entrance doors

Features of the work on the metal door

It is usually installed as an external, which always opens out. It will also be very good to inspire from the inside and transform from both sides.

Outer side

Transformation and warmingly metal door, do not apply insulating rollers around the perimeter. This door has a completely different destination - it is used as the main protection of the entrance to the dwelling and ill-wishers, and only then - as an additional protection from the cold.

Installation of the upholstery and insulation on the metal with hanging side is carried out on glue. In this case, the insulation is cut out by the size of 10 ÷ 15 mm M to the door of the door, both in length and width. The upholstery material should exceed its size by 50-60 mm - this part of the material will go bend around the metal shelves of the door canvase.

• On the metal surface, retreating from the edge of 10 ÷ 15 mm, and in several places in the middle of the plane, glue is applied.
• Then the insulation is placed on it and is well pressed against the door canvase. You need to give the time glue under the insulation to dry. A specific period will be listed in the instructions for applying a specific composition.
• Next, you can start gluing the leatherette. On the back of the metal plate from the top of the door, glue is applied to a distance of 50 mm. He needs to give a few minutes to grasp.

• Then, noting the middle of the width of the door and the casing material, it must be applied to the proclased place on the labels and carefully press, after which it is to give some time for good grasp.
• The next stage, the lateral parts of the door are in the same way, the shelves are bent and the casing material is bent and glued. If, when tensioning, excess squalls was formed, even a few millimeters, it must be cut off with a sharp knife, otherwise it will interfere with the door closing. If the casing material is sufficiently dense, then it may have to cut the corners so that the tightness turns out as accurate as possible.

Inner side

If the inner side of the metal door is not insulated, then you should think about this event. Usually, on the reverse side, the metal door looks like a frame, welded from a corner and profile pipe, to which a metal sheet is welded performing the role of the door canvase. It is already saved with artificial skin.

Now it is necessary to warm and separate the inner part of the door.

- In this case, a polystyrene foam with a door frame thickness is perfect for insulation.

- We will also need wooden rails of the same thickness.

- To compact the joints and seams, a mounting foam will be required.

- It is necessary to prepare a drill with a drill for a self-tapping screw for metal.

- For interior decoration, thin plywood, soft insulation and leatherette can be used.

• The first stage to the frame must be consolidated by wooden planks. For this, the holes are drilled in the corners or profile tube and the planks are fixed to them. Reiki is needed in order for them to be conveniently fixed the fane or other inner trim.

• To remove "cold bridges", between possible gaps between metal and rails are filled with mounting foam. By the way, she will give additional rigidity to the attachment of the rivers, as it has pronounced adhesive properties.

• After the rails are screwed and processed by foam, polystyrene foam panels are installed between them. The gaps between them and rails are also carefully filled with mounting foam.

• At that time, while the foam will dry, you can prepare the plywood sheet. Its thickness must be chosen in such a way that the door is easily pressed against the jamb, especially since the insulation and the insulation will be installed on it.
• The plywood blank must have the size of the inside of the door, insulated by foam, plus the width of the frame on the upper and lower sides of the perimeter of the door canvase.
• The entire area of \u200b\u200bplywood passes a thin insulation.
• Further, the plane is completely delayed by the leatherette, with a bend it on the inner side. The material is fixed on glue and is additionally fixed in several places with brackets.
• When the panel is fully ready, it is placed on it the location of wooden plates screwed to the metal frame. This process should be done very carefully, so that there are barely noticeable points on the trim, on which decorative nails will be clogged.
• It is possible that in the corners will have to be done by one more hole and fix the corners of the plywood skin with self-drawing to ensure a tight fit of this lining to the metal frame.

Video: Metal door upholstery with its insulation

It should be noted that, if desired, the plywood lining can be replaced by the usual clapboard of natural wood or laminated fiberboard. Its, starting from below, are fixed to the same installed slats.

Help the door of the skin or is completely easy. Having made this work independently, the owner of the apartment can save a rather large amount. Easy the calculations and the upholstery process will be able to purchase a finished kit, which includes a set of materials intended for the design of the standard door.

Video - how to bother the door to leatherette

Wooden entrance doors are very picky of our apartments. They need constant care, protection and restoration. Of course, few of us pays for this subject a proper amount of time and attention. That is why they often come into disrepair or simply lose the presentability of the appearance. There is no desire and the ability to replace the old wooden product to a new one.

But you can always upgrade it with your own hands video, give a fresh look and aesthetics, which is engaged by dermatitin. How to shelter Dermantine door? There are many video lessons showing how to do it properly. And with a clear step-by-step instruction, this will not be difficult for even people who do not have special skills and skills. Moreover, as a result, not only external beauty will be, but still noise and thermal insulation.

Before starting work, prepare all the materials and tools. The choice of material is so great that it makes sense to think about the future door design in advance. Otherwise, you will walk and choose for a very long time. You will also need a porolon with a thickness of 2 centimeters and batting, a building stapler, hammer, large scissors and nails are ordinary and furniture. First you need to prepare the door. To do this, disassembly door handle, eye, loops and all decorative elements.

Step-by-step instruction: Upholstery wooden door Dermantine with her hands video

We will make the manufacture of the so-called roller, it serves as the main element of the upholstery and closes the clearance between the door and the jamb. With the help of scissors, cut the dermatin band at 10 cm. Then place it with an inlet to the end of the door leaf and use the construction stapler. Instead of a stapler, you can use the usual hammer and small nails.

In order to avoid the uneven distribution of material in places of fixation of the door loops, cuts should be made on the Dermatin band. Now you can proceed to fastener. Place it smoothly on the surface of the wooden door and secure with a stapler. Next, the foam layer is stacked by batting in 2 layers. Batin is a reliable protection of the foam rubber and protects it, increasing wear resistance and service life.

Now you can do the dermal dermal. Cut part of the canvas in size in the door size, adding 4 centimeters on each side. Rivne to put the trimming material on the door leaf and begin to nourish with furniture nails. It should be started from the center, first at the top of the wooden canvase, then in the bottom. Do not forget to stretch the material well to eliminate all irregularities. Next, continue the attachment of dermatin around the door perimeter, slightly converting the cropped edges.

Now that the door already looks quite pretty, it remains to finish working with rollers. Batin, which remained after the door sheel, twist into the tube and wrap in the Dermatin bands, nailed to the door at the very beginning of work. Bring the resulting roller with furniture nails in increments of 7-10 centimeters.

This completed the upholstery door with his hands video. It remains only to install the eye, loops, a door handle and all the decorative elements that were on the door earlier. Now you can rejoice not only with a neat new type of entrance door, but also to your skill.

If you attach some more fantasy with the help of a metal thread and nails to create an interesting drawing, which will give the individuality of your door. In order to succeed, see how to properly hide the door canvas with your hands video.

Leatherette - Skin substitute, is one of the most sought-after materials. The most widely material is applied in construction and decoration.

The high demand for dermatin is justified by the following characteristics:

• Frost resistance. The material well performs its functions even at minus temperatures. It also helps to keep heat in the house, so it can be used at the entrance doors;
• Durability. Material retains properties from 7 to 10 years;
• Water resistance. The material has moisture-resistant properties, which eliminates the damage of the product or insulation;
• Soundproofing. Material can be used for the front door, because noise into the room will not penetrate through the canvas;
• Easy care. To preserve the type of dematin, it is enough wiping with a damp cloth. You can use a special cream that gives the leatherent shine;
• Antiseptic properties. Do not give in to bacterial rotting, mold and other pests;
• Resistance to aggressive chemical environment. The material can be washed with any means of household chemicals;
• Low cost. To obey dermatin by pocket an average family;
• Wide range of texture and colors.

Instruction - we are trimmed with dermantine

In the process of upholstery, it is necessary to adhere to a certain technology. It will maximize the useful properties of the material, and will provide a long service life. The procedure includes the following steps:

1. surface preparation;
2. upholstery insulation;
3. upholstery Dermatin;
4. decor accessories.

Each stage has its own nuances, so you need to carefully familiarize yourself with the peculiarities of the execution of listed items.

Preparation

If the replacement of the casing is carried out, it is necessary to stock knife, passage, and, when necessary, dismissed. The procedure is as follows:

1. Eating with loops.
2. Disassembly of fittings.
3. With the help of the passage, all decorative nails are removed.
4. Dermatin and insulation is cleaned. Getting rid of the insulation can take some time if it is attached to a metal door with glue.
5. The surface to the trim is prepared.

If earlier the door was not crushed, then all the fittings are removed. It is necessary to remove all the elements that are discarded on the surface. Under the dermatin should go flat surface, so you can align the relief using the plywood stove. It can be attached to ordinary nails. It is important not to forget to process wood with special means.

Insulation

First you need to decide on the insulation material. The most suitable under dermatin are:

• Porolon. Low price, a wide range of density and thickness. It has an operating time equal dermatist. Possesses medium insulating properties;
• Batting. Inexpensive material, with a service life of 30 years. However, over time, peasants, and can absorb moisture. Is toxic when burning;
• Isolon (subspecies of polyethylene). The most modern option. It has good insulating properties. The most expensive of all materials, but the ultimate cost will not be too high.

On the wooden surface, the insulation is fixed with a stapler. From the outside of the edge, it is necessary to retreat to 8 cm. On the entire area, without an incidence, the insulation is applied. The markup is applied to work the stapler or clogging of nails. The step between brackets or nails should be 10-15 cm. Processing is carried out throughout the perimeter.

For metal surface, glue is needed, which is also applied around the perimeter, retreating up to 8 cm from the edge. You must not forget to crop the insulation on the handle, castle and eye.

Preparation of tools, accessories

To rationally use the time, it is necessary to get a set of necessary tools before the upholstery. The set includes:

• a hammer;
• stationery knife and, if necessary, scissors;
• stapler (if not, the hammer is used);
• roulette;
• marker;
• tassels (for metal surfaces).

The list of tools and materials for wooden and metal doors is slightly different. Therefore, the technology of plating each material has its own. It is also important to acquire immediately by all materials:

• leatherette;
• insulation;
• staples for a stapler or nails (wooden surface);
• glue (metallic);
• decorative nails;
• tape (in case you need to additionally fix the dermatin, and decorate the door).

Reference! Choose decorative designs for design will not be difficult, since the market is filled with products of different shapes, values \u200b\u200band colors.

Upholstery technology

Work together will be worse. The second person will help stretch the cloth for the convenience and flatness of the relief. The edges of the canvas are always flexing inside, which will make the field of durable and aesthetic field. Positions must be several centimeters. The wooden door is ridiculous with carnations with a decorative cap. Step from 10 to 15 cm.

Important! It is necessary to ensure that the insulating rollers do not look out from the grounds.

Dermatin should not cover the door to the very edges. Several millimeters need to retreat, which will provide free movement.

Figure design is often used with decorative nails. Soft insulation allows you to create a relief on the surface, which will completely transform the door. Be sure to mark the marker to mark the places for installing accessories. Next, cloves are clogged, which usually have a removable decorative hat, so as not to damage it when mounting.

There are a large number of drawings that can be created on the surface: from simple points to geometric shapes, such as diamonds, squares. On the Internet you can find many schemes for furniture nails. Between the nails, you can stretch the decorative thread that will change the drawing and relief.

For the metal door, the drawing should be inventing even at the preparation stage to fasten the base of the screw buttons. In the insulation and dermatit, fine holes for screw buttons are pre-done.

Wooden Door Upholstery: Video

Upholstery has its own nuances. Wood needs to be careful. Therefore, often wooden doors have a non-primary look. A good restoration option is Dermatin's upholstery.

The tree must be treated with an antiseptic. Working with a wooden cloth, the lining must be fixed with a stapler. Since glue is required for the iron surface, the wooden canvas to knock the brackets much easier.

Furniture cloves are used on the edges.

To decorate the doors correctly, you need to follow the instructions given on the video.

How to shelter the metal door dermatitin?

The metal door is usually placed at the entrance, so it is extremely it is important to use high-quality insulation. It is often insulated only the inner side, however, the range of decorative accessories allows you to decorate an outer side using the insulation.

For a metal door, insulating rollers are not required from the outside. The size of the insulation must be less than 1-2 cm around the edges of the surface area. Dermatin needs to take a piece more by 5-6 cm around the edges than the door area. This is necessary for the bend. The upholstery process consists of the following steps:

1. Glue is applied around the perimeter, retreating up to 2 cm, and thin stripes in the area.
2. The insulation is applied, and pressed for a while. The lifetime of glue is listed on the packaging.
3. Starting from above, glue is applied to the opposite side of the product at a distance of 5 cm from the edge. Press the dermatin for the grasp of glue.
4. Similarly, the procedure is carried out on the side edges. It is important to pull the cloth to a uniform relief. Sometimes you have to cut off the extra pieces that will prevent close the door.

Inner side

The inner side of the entrance door can be insulated with polystyrene foam. Thus, it will be possible to simplify the upholstery procedure of Dermatin. The insulation process is as follows:

1. By the door area, the frame is fixed under the foam. This uses strips having polystyrene foam plate thickness. Reiki are fixed using metal screws, which are fixed in pre-done, holes.
2. All large seams and joints are closed by mounting foam.
3. Foam plates are installed in the frame, which are fixed on special glue. The gaps between the plates and rails are also close to the mounting foam.
4. A sheet of plywood, smooth door area, is nailed to the raids.
5. Next, the procedure is similar to the upholstery of wooden products. It is just important to monitor that decorative nails be nailed to the location of the plates.

From the inside, the warming rollers are attached to the door frame. They must be placed in a leoping drimmer. From the reverse side and on top of the ledge should be up to 5 mm. Bottom, the roller is located at an altitude of 1.5-2 cm from the floor.

When choosing a material for upholstery, it is important to remember the disadvantages of Dermatin:

• Low fire safety. Fast flammable material, which, when combustion, highlights caustic smoke;
• Not the most durable materialwhich is easily scratched and cutting;
• With mechanical damage it will not be possible to return the former look.

There are also important points that need to be considered when choosing Dermatin:

• The material must be elastic. The hardness of Dermatina testifies to the fake;
• Choose a coarse cloth;
• The sharp smell indicates low quality of the canvas.

Conducting Dermatin's upholstery, it is important to maintain the sequence of the process, and take into account the features of the materials used. If the technology is not broken, then this upholstery will last up to 10 years.

Source: https://tkaner.com/materialy/dermantin/kak-obshit-dver/

Step-by-step guide to Dermantine Doors

Dermantine doors upholstery - an easy and inexpensive way to decorate and insulation of the home, which begins with the entrance to the house or apartment.

To fulfill this job, you will need knowing some features of the doors.

Namely: the properties and characteristics of the dermantine used by the lining material, tools when working with wood or metal, decorative, fasteners, and more.

Dermantine (from ancient Greek leather) is a grade of artificial leather made of cotton fabric and a nitrocellulose layer covering the fabric from one or two sides.

Dermantin for the upholstery of the doors is positioned on the market as a substitute for an expensive genuine leather, not inferior to it in separate characteristics. It is also used to upholstery furniture, book elements, bags, wallets and car salons.

Dermantin is a finishing material that has the following pluses:

• Not subject to rotting and decomposition, resistant to various microorganisms;
• Moisture-resistant, does not allow moisture to penetrate into the layer of lining material, protecting it from the appearance of mold and unpleasant odor;
• Relatively durable material capable of listening to ten years with proper care;
• Resistant to abrasion and effects of chemical reagents (acids and alkalis);
• It is easily clean and cleaned by conventional detergents: soap and powder;
• It is frostable, able to withstand temperatures up to minus 35 degrees (depending on the type of dermatine).

Despite all the positive properties of Dermantine, many are not satisfied with its disadvantages, namely: with the slightest damage (cut or break), the leatherette cannot be repaired and replaced with a separate part, thus the complete coverage of Dermantine doors is required.

When combustion, the leatherette highlights harmful substances, unsafe for human health and contributes to the rapid spread of fire, as fuel and fires.

These minuses are not so important if you consider that Dermantin has a lot of useful consumer qualities, some of which are described above.

The distinctive properties of Dermantine include that the leatherette can easily and simply cut, it does not roll, it does not occur and does not give a shrinkage. In addition, there is a fairly wide selection of types of coloring material from gray to red. So you can choose what the most harmonious fit in the interior of the apartment.

What characteristics need to take into account when buying leatherette? When buying a dermantine for upholstery, attention should be paid to how the material is stretched, it does not form cracks during the tension. Also look at such a parameter as wear resistance, it must be at least 30,000, and better all 50,000 cycles. The greater the number of cycles, the stronger the fabric to abrasion.

Dermantin should be resistant to the appearance of fesoms from the fold of the material and scratches. Also, consider the characteristics of dermatin on resistance to ultraviolet radiation, if your door is under the right rays of the sun most of the time.

The surface of the leatherette can be smooth or matte, imitate the aged skin, etc. Pay attention to the flower range of artificial coating, what color and texture will be best harmonized with the design of the handles and loops, eye and other fittings.

Normal and decorative upholstery

Choosing a force for upholstery in the store, take into account the type of doors' tanks. There are two types of tie: ordinary and decorative.

Ordinary upholstery includes a simple finish of the door leaf with a smooth leaf of the leatherette, which is attached to the base only around the edges. The perimeter also creates a decorative tape, fixed on the door every 10 cm.

Decorative or regulatory upholstery Dermantine doors is a peculiar finish performed on the basis of wood or MDF - panels that are navigable to the door canvase.

First, the fabric is tensioned throughout the door of the door, and then in separate places it is fixed with buttons or nails with leather caps.

At the same time, the pattern on the canvas from the buttons may be rhombid or square, depends on the preferences of the room owner.

Schemes and drawings of decorative upholstery.

Elements of the trim for the wooden door: rollers, lining material, nails

When preparing for a drawing, it is important to know about the basic materials and elements, thanks to which the process of plating the door is.

Rollers

Upon the upholstery of Dermantine doors use rollers. The roller is a special element that serves to protect the house from drafts and cold. It forms a tube of lining and dermantine, nailed around the perimeter of the entrance to the door leaf or on the door frame.

The method of accommodation depends on the type of door opening. If it opens the inside of the room, then the roller has from the back of the entrance to the house. The roller should go beyond the box of several millimeters. At the same time, the distance between the blade and roller should be so that the roller "slowed down" the opening of the door and she slammed with a little effort.

With the method of opening the design, the roller is naked to the door canvase. At the same time, it is fixed first, and then add a lining.

Dermantine doors' upholstery is carried out without roller only in one case: if the metal design is installed without special bars, allowing you to fix rollers to them.

Lose material

The upholstery lining is most often used foam or isolon with the addition of batting. It is not excluded to use one wattin or syntheps. When applying the latter, it turns out a more rigid and ribbed design.

Porolon allows you to achieve softer and smooth surface drops. It has the best properties of sound insulation than batting and syntheps, and the most outstanding thermal insulation boasts isolon.

Isolon is a new lining material from polyethylene, more expensive, but also more perfect. It does not miss the cold air and absorbs noise, being an environmentally friendly material.

Nails

Upholstery Dermantine doors is carried out using special nails having broad hats. Men's nails can be both metal and leather (dermatin). Steel nails are silver and golden.

Leather nails are manufactured by hand, so their cost can be somewhat higher than normal. In addition, there are special decorative nails serving the decoration of the doors.

To betray the door canvase, a beautiful and modern view is not at all necessary to spend huge amounts to pay to the masters on the drawing. The upholstery of the Dermantine door is made easily and simply, only the correct preparation of the door to the drawing and tools with materials is necessary.

Preparation Door to a Treatment

How to determine the dimensions of the material necessary for the upholstery of Dermantine doors, given the dimensions of the door canvase?

The leatherette should be equal to the door area plus 15 cm on each side. For rollers, one cut is required 14-15 cm wide and a length of equal to the height of the door and two cuts, out the width of the door canvase.

The number of rollers increase if the door opens outwards (all four sides). The foam or isolon is cut out the size of the door cloth, the thickness of the insulation should be no more than 2 cm.

We still calculate the number of nails. It depends on the drawing and distances between nails. For a standard door, it may be necessary somewhere 50-60 pieces without a drawing.

Tools for work: hammer, stapler, knife, pliers, scissors, nails. For metal doors, the upholstery is carried out without nails, on adhesive basis. The glue will need at least 100 ml.

Technology covering doors

The door is released from everything too much: from the handles, loops, old upholstery, etc. At the first stage they will only interfere. Methods for fastening the leatherette to the door canvase differ depending on the door manufacturing material.

Wood

We make rollers: directly on the doors fix the leatherette strips face down with a stapler. We are deploying the tube insulation and convert, closing the foam. We clog the stapler or nails. At the bottom of the door leaf, the material should be scored so that the distance between the roller and the floor is 1-2 cm, otherwise the roller will simply move in places of touch to the floor.

We strengthen the lining: a stapler fastener from the middle of the door leaf (as the likelihood that the material turns to zero). The lining is dripping so that the distance to the edge of the door was 1-2 cm. On the stroke of the foam onto the batting (it protects the foam rubber from damage).

Krepim Dermantin: First, we turn on the top 6-8 cm and fix the nails, follow the folds and the folds and the races. Then, straightening, stretch on the sides and clog nails around the door perimeter. Properly stretched material does not frown and does not form a fold. Distances between nails maximum 10 cm, minimum 5 cm.

For the metal door, the process is a bit faster and easier, the mount is occurring with the help of glue.

Metal

The door is removed and put on a flat base, for example, four stools. Loss of glue around the perimeter of the canvas and in the center, fix the insulation. Press the foam rubber to the surface and leave a little dried.

Then glued the main cutlery cut starting from above, just like with a wooden structure, moving to the sides and ending with the bottom.

We hope our article will help you easily and easily fulfill all stages of work.

Source: http://o-dveryah.ru/remont/obivka-Dermantinom/

How to hide the door

Taking orders daily from 9:00 to 21:00

(detailed video instructions For self-upholstery doors, look at the bottom of the page)

In this instruction, we will tell you about how to put the entrance door yourself. For this you will need: 1. Vinilisza (Dermantin, Artificial leather, leatherette, PVC film, vinyl and leatherette). Viniliskow is sold on a cut, width, as a rule, is in the range of 110 centimeters to 140 centimeters.

If you have a standard metal door, then there will be a piece of matter for its upholstery, the dimensions of which are more than 10-15 centimeters. If your door is wooden, then it is necessary to take into account that in addition to the sheathing of the main doorway, it will be necessary to make rollers for which the dermatine strips 12-15 centimeters are used.

We will need three strips in length equal to the height of the door.

2. Lining material. For these purposes, it is possible to use a thickness of 10-20 mm thick. If you need enhanced thermal insulation and noise insulation, then pay your attention to such a material as isolon.

The foam rubber is sold by the meter size by two, which is just suitable for high-quality door upholstery.

3. Upholstery decorative nails. Usually used special furniture nails with a wide hat. The color scheme consists of shades for gold, silver, bronze and copper. We recommend picking up the color of the nails coinciding with the color of the locks and the handles. Thus, your door will look quite harmonious. Also in the construction markets you can find nails, whose caps are pulled by vinilies. You can choose nails that match the texture and color with the selected material, or you can turn around to play in contrast.
4. Glue. It will be needed if you have an iron door, in which no holes for nails are provided. For our purposes, the "moment is universal" is well suited. For pasting one side of the upholstery, there is enough tube with a capacity of 100 ml.5. Tools.1) Building Stapler and Staples with Leg Length 8-10 mm.2) Hammer.3) Scissors.4) Knife (You can use a regular stationery knife with interchangeable blades) .5) Unscrewing. 6) Pasali.7) Tassel ( For plating a metal door).

After you have seen that all of the above items are available, proceed directly to the upholstery process. First of all, it is necessary to dismantle all the locks, door eyes and get rid of the old trim (in the event that you need to move the door). Here we will not describe this action, and immediately begin the story about the main thing.

At all, it is not necessary to remove the door with the loops, as advised in many similar instructions. So, we divide our guide into three parts: the upholstery of the inside, the upholstery of the outside and the pasting of the metal door. But remember: instructions on the upholstery of the door gives only general recommendations and does not take into account the specifics of a particular door.

In some points, you may have to turn on the smell.

How to gather a wooden door with your own hands

Consider the situation when the door opens inside the apartment. To beautifully cut the wooden door yourself, it is desirable to start working from the manufacture of a roller, which will visually close the gap between the door frame and the door itself, and in some cases - and tightly lay down to the box itself (it depends on the design and profile of the platbands).

First, we take one strip of dermantine and with the help of a stapler you feed it with the front side to the door surface so that it goes to the door for about 3-4 cm. If your door lock is installed on your door, it is better to start to nip the roller from it. If all mortise locks, then begin to sow a door from the top corner of the loop side.

Extremely thus the entire perimeter of the door strips of the leatherette, proceed to the styling of the foam rubber. It is necessary to cut it into the strips of 8-10 cm wide. The stapler fasten them on the doorway, we bring and nail the material so that the resulting roller spoke is 1-3 cm. Depending on the relative location of the door and platforms.

Roller ready.

Next, we measure the resulting distance between the inner edges of the roller and cut out the foam rubber, using these sizes one centimeter on each side. The stapler fasten it on the door canvase. The final part remains - to hide the main surface of the wooden door.

We take a piece of dermantine for an angle, we bring the edges by 5-6 cm, lay in the angle of the door so that the material is slightly entering the roller and nail a decorative nail with a hammer, retreating from the edge of about 5-7 mm. Then we take the second top corner of the material, also we add it and, slightly pulling, scoring the second nail.

Next, you need to check, exactly leaving a piece of leatherette relative to the surface of the door canvase. To do this, in the middle of the door, a little pushing, spend your hand from the top to the niza himself and, holding one hand, the second we apply the lower corners of the matter to the edges of the door, smoothing them from the center.

Accordingly, on the left, and to the right, the distance to the edge of Dermantine should be the same. Making sure that the beginning is right, we continue the upholstery of the door. You nail the top edge, making the distance between the nails 10-12 cm.

Then we start to do the same with any side side, converting artificial skin at an equal distance over the entire length and slightly, but not much, pulling it. It is important here that it is not to drag Dermantin, otherwise you will get something like skirts with folds.

Fix it will be not easy, as you have to pass out already scored nails, while there is a high probability that you accidentally damage the upholstery material, and in any case, there will be traces from nails. Reaching to Niza, proceed to the second side.

Last but fix the lower edge of the upholstery material, having previously calculated the future distance between the nails so that it was the same throughout the bottom of the door. Everything! Door of the uphreat. It remains to install locks and eyes. Help the wooden door with their own hands is quite difficult to the unprepared person, so many firms offer their services for the upholstery of doors.

How to shelter the outside of the wooden door himself

The outer side of the wooden door should be hampered by dermantine somewhat in any way. First of all, you need to close the door and pencil to draw the projection of the door frame on the door leaf itself. In other words, make a pencil line throughout the perimeter.

It turns out the outline of the future door sheath, and the remaining indent is needed for the so-called "quarter" door. If the door is installed professionally and the locks are properly adjusted, then the door canvas should fit tightly to the box and, if with the upholstery we will earn the dermantin per line, then in the end the door simply will not close.

Now you feed the lower part of the insulation roller. Freshing it on the door so that in its closed position he firmly lightened to the threshold. For this, we already have an outlined border below. If the bottom roller navigate to the threshold itself, then over time it wipes from constant hiding legs. Next, fix the lining material with an indent from line 1 cm.

and similar to the previous paragraph, you feed the main piece of vinylister. Now it is necessary to make a warming roller on the right, on the left and upstairs. In this case, it will be attached on the door frame. It is done in almost similar to the inner roller, only it is advisable to fill in a large number of foam rubber.

From the loop side, we place it flush with a jamb, and with the upper and keyfields - we push about 3-5 mm by approximately 3-5 mm, depending on the size of the slots between the door blade and the box. If the roller make a roller too big, the door will be closed hard, with effort.

If the roller succeeds in a small size, it will not perform its main function - sealed opening. Therefore, it is important to catch the Golden Middle. In conclusion, you feed the remaining bottom edge of the trim and install eyes, handle and locks. Do not rush at this stage. As they say, it will die seven times - a rejection once.

Do in the upholstery of the slot under the locks and handles with accuracy, do not cut off too much. It will be offended at the very end of the process to lock all the work done. Now you know how to see the outer side of the wooden door himself. This will significantly increase its insulation properties, as well as the input door noise insulation.

How to hide the metal door dermatin

We take a tube with glue and brush and wipe the entire perimeter of the metal door. Then we apply a sheet of foam rubber and, slightly pressing it on it, glue. Further, the stationery knife is cutting into the foamonalone exactly along the profile of the metal sheet. If the blade is acute - this procedure will be quite easy and pleasant.

Now we apply the glue to the top end of the door (if it is the inner side) or on the back side of the top nickname (if it is the outer side). Using glue, be sure to follow the instructions for use! Further glue Dermantin and, similar to the method above, we check the uniformity of its distribution.

Then we glue the leatherette from the loop side. And then - and from the lock side, pulling the right hand with a lightweight effort, and the left - driving the surplus of Dermantine. So, the lower edge remained. Apply glue from this side of the metal door of the most difficult.

There are situations where the gap between the lower edge of the iron door and the floor is only two to three millimeters. If you can't glue the leatherette from below, you will have to remove the door from the loops. Thus, you can significantly facilitate the task.

When the fabric is glued with all four sides, the stationery knife is gently cutting off the surplus on the corner at the shelter of the end and the nickel (the GRATOR), put the eyes, door handles and locks. As you can see, wining the metal door itself is quite possible. Try - and sooner or later you will succeed!

Source: http://profobivka.ru/obitdver.html

How to see the door of wood, metal

The easiest and most popular way to give the door attractive appearance is to hide it with some material. It is possible to do it out of the room, and outside, use only different materials and different technologies. But in any case, the process is called "doors". All subtleties and nuances are below.

What can you beat the door

There are two types of doors upholstery - soft and rigid. Soft make two materials - Dermantine (Dermatina) and vinylisodes. Dermantin is a woven cotton base covered with nitrocellulose film. Popular This material was in the 40s-60s of the last century, as it was practical and inexpensive.

A little later there was a vinyl slip. This material is made on different bases - woven and nonwoven, drawn and not. Accordingly, the artificial leather has different properties. A layer of polyvinyl chloride (PVC or PVC) is applied. It is more durable, chemically neutral.

It has only one significant disadvantage - it reacts poorly to ultraviolet rays - loses elasticity, changes the color, can crack. Therefore, the upholstery of the doors emerging directly to the street, vinyl scribbling.

There is, however, a material with increased resistance to UV rays, but it is special material and it is necessary to pay attention to the purchase.

Door upholstery leather: several options

Now about a small confusion in terminology. Dermantin is in its pure form, such as he was in the past century, not done for quite a long time. Instead, there are different types of artificial leather from vinyl.

There are also materials coated from other polymers, but they are not so much. That's all of them in old memory and are called dermatin or leather (although it is right, by the way to say "dermatin" without "n").

So seeing this name, it is necessary to specify which material it is meant, as properties and prices differ significantly.

Despite the fact that the material is essentially one, it has different characteristics and appearance. There are elastic species that are well drawn, there are hard, which is difficult to stretch. In addition, modern artificial leather has many colors and shades, can have a different surface structure:

• smooth - brilliant and matte, there is even with the effect of "metallic";
• porous;
• structured, imitating different types of skin (snake, crocodile, etc.).

  Under crocodile skin

So choosing soft upholstery materials for the extensive door. Apparently, this is the determining factor in the popularity of this type of door upholstery.

Tight upholstery materials for doors more, although they are used less often:

• mDF panels from 8 mm thick to 18 mm;
• natural wood - fragments, array;
• veneer;
• laminate;
• plastic;
• postforming.

Of all this list, most often the doors are separated by lining / MDF panels. This upholstery is especially popular for decorating metal doors, including self-made. The panels are manufactured in size of a particular door leaf, after which they are installed on glue or mounting foam in fixed starting strips. In this case, it makes sense and discarded from MDF.

From the catalog - options for MDF lining, and all this is still in different colors ...

Practically also passes the plating the door with other materials - laminate, plastic, post-forming. On the perimeter of the door, starting profiles are installed, in which the fragments of the finishing are inserted. Everything is simple, in the presence of elementary skills of working with a drill, saw and hammer, you can make it yourself in a few hours.

Dermantine doors upholstery

The most popular way of plating the door - with the help of artificial leather. Such a department allows simultaneously with improving the appearance to increase the indicators of heat and sound insulation. But this type of door upholstery and cons is the most complex technological process that requires at least general ideas about the procedure for action.

Outcome methods

Speech will go about the upholstery technology Dermantine. You can attach it in two ways: with a roller around the perimeter of the door canvase and without it. Depending on this, the procedure is changed (a little later).

Upholstery Dermantine doors - with a roller and without it

Examples of drawings for upholstery doors Dermantine

For the redesign, you can use the same material that the doors have crossed. It is cut into a strip of 2.5-3 cm wide, attached to the upper nails, and then stretching and fixing for the next nails, form a pattern.

To secure the strip it, it can be wrapped around not until the end of the driven nail, which is then clogged. But this option is suitable if decorative nails have large hats.

If the hats are small, the strips are nailed.

Also, the drawing can be formalized using a thin metal flexible cable, but it is harder to fix it - it bends worse.

How and how to fix the dermatin to the door canvase

If the upholstery of the wooden door is needed, the questions usually do not occur - they are attached to the brackets from the stapler, on the contour then nailed with decorative nails. Only here there are nuances: staples should be with a wide back (not less than 1 mm), and nails are bulk, with a wide hat. Fastening installation step - from 2.5 to 7 cm, optional.

Most often wallpaper nails

More questions arise when it is necessary to cover the Rutan iron door. Here the output is only one - perch on glue. The glue is usually used by the "moment", but you can be any other universal that can be glued and metal and leathes.

They lubricate the nickname from the inside (bar, which goes around the perimeter of the door and closes the interface with the door frame). When fixing the vinylisms, it is cut out with a margin of 15 cm, just for the bending on both sides on the wrong side.

Materials for heat and noise insulation

Most often used for the insulation of the door of the foam rubber. It is inexpensive, if desired, allows you to form a bulk convex pattern. The most common case is two layers of foam rubber 1 cm.

This option is not the best - the foam rubber almost does not affect the sound insulation properties of the door, namely, this is sometimes very important.

In addition, after 3-4 years, it loses her elasticity, it starts sticking out, it is necessary to make a doors to do, although the appearance of the leatherette is still quite decent.

All this is so, but there are no worthy competitors for the foam rubber. There are materials with certain properties that can be put instead of one of the layers, and the second will still be foam. For example, "isoton" can be used to improve sound insulation properties.

It is used for the heat-insulation of cars. Sold by small sheets, an adhesive composition is applied to the back side, protected by a polyethylene film. So there will be no problems with installation. Of the minuses - the price and fairly large weight of the material.

In order not to have problems, it is worth replacing the loop to more powerful.

Materials for noise-heat insulation doors

There are two more material used in the automotive industry, with similar properties. It is "splen" and "vibro filter". All of them are made on an adhesive basis, can be used to improve the characteristics of the door.

How to beat a wooden door

It is more convenient to work on the doorned, but if this is a problem, you can knock on the spot. First you need to remove all the accessories from the door cloth - locks, latches, door peephole.

If there is an old upholstery, it is neatly removed. If part of the door requires repair, damaged fragments are removed, replaced with cut-made wooden.

The slots can be smeared with putty or tinted by mounting foam with a small expansion coefficient.

Options

If there was a drawing on the upholstery, and he basically suits you, to the places where the forming drawing of nails were driven, drive the usual. They are not scored not to the end, the hats should be stitching by 1-1.5 cm.

With their help, then vouch in the right places, foam rubber and upholstery (just put pressure with your fingers, all layers are sold). Ordinary nails pull out, install decorative on their place, using a tape form a drawing.

The procedure is simple.

That the end of the door look at no worse than the rest of the plane, starting with it. If one of the parties are not going to separate, this stage is missing, just paint the paint end in the tone of the finish from one or the other side.

If you cut the doors from two sides, we cut the material strip of a width of about 10 cm. More precisely, look at your door, as the thickness of the canvas is different. The band should close the end and go on one and the second side by 3-4 cm.

Strip stack, fasten on the edge of brackets from the stapler (faster and easier) or nails with a large flat hat.

Breeping strip on the end

To form a roller, the material is also needed. Width - 10-15 cm depending on what width you want a roller. Next there are two options:

• Immediately form a roller. To do this, in the middle of the strip laid the harness from the foam rubber or batting, it is crimped in the middle. This form is fixed around the perimeter of the door. After, top, the foam rubber and the material is stacked. To form a neat edge, the material is seduced inside.

  The roller is formed immediately, in the finished form is attached around the perimeter of the canvas

• The roller is formed later, after the vinyl is laid on the canvas. Here the technology is different - the strip is attached around the perimeter, the front side down. Then the foam rubber and the upholstery material. The edges are not converted, they are simply cut into size. After the end, the band turns on the front side (it is possible to put a strip of the foam rubber), begins and fastened by bulk nails.

  The strip for the roller is fixed in advance, it is formed after the upholstery material is fixed.

The difference between these two ways is only in appearance: in the first case, nails are nails on the edge of the upholstery (in the photo on the right), in the second - on the edge of the roller (in the photo on the left). Choose someone else like it. For example, it seems to me that the first option (right) looks better - more neat. But this is only a personal opinion.

Two rolling formation options

What do you need this roller? In order to overlap the possible gaps between the web and the jamb. Thus avoid the appearance of drafts and reduce heat loss.

But it is possible to make a roller only if the doors on the opening side are hurt (the doors open inside the apartment, then from the inside and we are upful of them). If on the other hand, this focus will not pass - it will not cling.

Then you have to do without roller.

Without roller

In this case, everything is simple: the canvas is exactly separated, fixed with nails or brackets - who is more suitable.

Without roller

Door upholstery process in photo-format

To reduce the level of noise, the doors are hurt by one layer of noise insulation and one - foam rubber. A variant with pre-making roller is selected. At first they removed the old fittings, cut a new castle. The lining and the handle were removed, the internal parts remained in place. We proceed to the upholstery of the doors.

Immediately form a roller - in the Dermantine strip we are laid a narrow foam rubber, fastened around the perimeter of the door. Make it more convenient to braces from the stapler.

Nail roller around the perimeter

The next step is both soundproofing. It is on adhesive basis, so there are no problems - cut out in size, gently removing the film was glued. By gluing, we try to squeeze all the air, for this, the film we grip gradually, stroking the material from the edge to the edge.

Adhesive sound insulation

Now foaming is a thickness of 1 cm. In this embodiment, the most convenient way is the staples from the construction stapler. First, fasten around the perimeter, then often - on the surface of the door, so that the foam rubbed is tight.

We are placed and fastened foam

The foam rubbing with a slight margin, after mounting the surplus is cut.

The upper edge we add to 2-3 cm, starting starting from the left upper angle. They score the first nail there, then we put the material and nail the second above the right. Then, with a step of 3-4 cm, nail the upholstery from one edge to the other with finishing nails.

Having turned on the top edge, kpripim it

Crepim from the loop, having turned the edge inside. Place smoothly so that there is no chances at the top.

Nail from the loop

After the same operation is repeated from the castle, then below. Actually, the upholstery of the doors is almost over, you just need to install accessories in place.

Install the pads of locks and accessories

- Turks on the topic

Vinilisor for the upholstery of the door is sold both on meters and in sets. In some sets, the fastening method may be different: they have plastic profiles that are attached around the perimeter of the door leaf. These profiles have a fixation system by type that used in stretch ceilings. How to beat the doors in this case, look in the video.

The following video captures a process using a roll material.

How to insulate and enjoy the entrance door. The technique of forming a roller of the second type - it is nourished last.

How to hammer metal doors

The facial part of metal doors is rare - it also has a completely attractive appearance. The inside suffers more often. That's about it and talk.

On the iron door on the inside there is a frame in some models it is metal in others - wooden. The heat-insulating material is placed between frames of the frame. It can be a foam or mineral wool slab. They are attached to the mounting foam, having a very small expansion coefficient (required!). From above, everything is closed with a sheet of plywood or OSP.

This is a standard option. If the planks are wooden, everything is fine, there are no problems - no doors will not be freeze. But if the frame inside the door is metallic, with good frosts, everything is frozen through - through the bridges of the cold, which are metal ribs.

So that this does not happen, on top of the foam / mineral wool it is stacked again, the layer of "isotone" or "splen", and they are already Faneru.

The remaining processes in the upholstery of the metal door are very similar to those described above. All difference - in the method of fixation: the upholstery is glued to suitable high-quality glue. Surplus is immediately cut off at the place of the joint, using a sharp wallpaper knife.

Here it is just a classic error - there is no layer cutting off the cold bridge. Otherwise, everything is shown not bad.

The choice of doors is the point responsible, because it must protect the room from strangers, have good sound insulation characteristics and not pass heat. It is exactly the indicators that have a wooden or metal door, sheathed and insulated with special materials.

The cost of the covered product is an order of magnitude higher than the value of the usual door web, so not everyone can afford it. In order to save, you can shelter the door yourself, the benefit of this method is quite simple and inexpensive. As an incentive prize, you get a reliable insulated door that does not pass excess noise.

Dermatin is most often used as a casing material because of its unpretentiousness.

TERMALINESS

The choice of dermatina is a simple matter, because there is no significant difference between domestic and foreign manufacturers, unless in their cost. When buying you only have to decide between already ready-made sets, including fasteners and foam rubber, and an independent choice of all necessary parts. When buying Dermatin, we note that for a wooden door it is necessary to take a segment for 15 cm wide of the door leaf, and for metal - by 12 cm.

As a heater, it is recommended to use a foam rubber, the thickness of which should not exceed 1-2 cm. You can also try to insulate the door with an isotone, which has the indicators a little higher than the foam rubber boasts, but the cost is not low.

Note! Special nails having a wide head are used as fasteners.

The color of the head is chosen to the tone of the material selected for the sheat. For the attachment of dermatin on metal doors, the "moment" adhesive

A set of necessary tools includes:

• tassel;
• scissors;
• construction stapler;
• passatia;
• a hammer;
• screwdriver.

Wooden doors

Door's upholstery takes little time, so there should be no problems, especially if it is strictly followed by the following plan of action.

1. The door is removed from the loops, after which we spin the fittings. Freed from unnecessary parts of the canvas laid on a flat surface.
2. Remove the remains of the old upholstery material if it is available.
3. To the wooden floor with a stapler, the lining material is mounted, although you can use for fixation and ordinary nails.
4. Cut the dermatin is necessary according to the release of 15 cm in width.
5. Upper edge Over and secure, evenly distributing the material. Now we do, too, with dermatin on the sides, but simultaneously on both sides, to gradually pull free material.
6. The lining insulation must be laid so that he performs a little on the spare edge, which will make it possible to make a small roller when preventing the casing material. The resulting roller should perform 5 cm beyond the door. Fix all this selected fasteners.
7. We make the same roller on the sides of the door canvase. In this case, it is necessary to monitor its thickness, which should be the same along the entire length of the upholstery material.
8. When fixing the skin, make sure that the folds arising from insufficient tension remain.

Now you can proceed to decorating the appearance of the skin. With the help of selected braid and nails form a specific pattern that you choose yourself. Most often it is a rhombus or square. The decorative braid is tensioning from one corner to another and the cross will be enshrined with nails on the casing material.

If the dermatin for one or another reasons moves away from the door, then it can be fixed with a tensioned horizontally tape. The fasteners are recommended to be located at a distance of 10 cm.

Note! The lower roller must be 15-20 mm from the floor.

At the final stage, it remains only to place all the fittings in its place. Door's upholstery is over - admire the result.

Metal

The trimming material is attached to the metal canvase with glue. Consider the procedure for this operation.

1. At the edges of the door leaf, glue is applied, after which the foam rubber is attached. The peeled edges of the material are neatly trimmed with scissors.
2. Next, the glue is applied to the end part of the door at the top. It is recommended to closely monitor the emerging folds and skews and during them to correct that the result satisfy you.
3. After drying the glue, the stationery knife is removed excess material.
4. Fasten the handles and locks in your place.

With the help of these two ways, you can upgrade the appearance of any door and improve its characteristics, while the cost will be minimal. Using ready-made trim sets, you save the precious time, although in terms of cost they are a bit more expensive. From the segments of the material you can make an interesting miniature and consolidate it on the door.

Video

Tips on the doors upholstery technology you will learn by looking at the next video:

Over time, any door loses its external characteristics, but still continues to serve it. What to do in this case? The purchase of a new door is quite expensive. The easiest way is to fulfill the upholstery doors with your own hands. It can be seeded with leather or cheaper material - dermatin. You not only give the door an attractive look, but also improve the sound and thermal insulation in the apartment. Below is an instruction with a photo, how to step by step. It will not prevent additionally view the video with a master class from professionals.

What materials are suitable for doors' upholstery?

The choice of materials for the upholstery of the doors is quite extensive. The most popular belongs to:

• skin substitute (Dermantin);
• natural skin;
• mDF panels;
• lining and tree.

Each material has its own positive and negative sides. Therefore, before proceeding to the upholstery of the doors, you need to thoroughly weigh everything for and against and calculate your budget.

Most often, the doors are trimmed with leather or dermatin. This is an inexpensive option, and very attractive. But his main minus is a short life. It requires careful circulation.

Genuine leather is considered a more endless material, but its value is different from Dermantina to the most side. She will serve much longer. The door covered with genuine leather has a rich and beautiful appearance.

Council. Using decorative nails, you can create unique patterns on the door.

If your metal door is, the MDF panels will be suitable for upholstery. They are strong, resistant to external influences and not very expensive.

MDF panels are divided into three categories:

• painted;
• wooden (made of oak, beech, etc.);
• laminated.

Some panels, such as laminated, can mimic the appearance of the tree. Manufacturers achieve such an effect due to the special panel coverage. And, of course, the panels made of natural wood are the most reliable and steady option. The choice of material for the upholstery of the door depends on your preferences and budget for work.

Removing the old door upholstery

The process of placing the doors is preceded by the removal of the old layer. To work, you will need:

• passatia;
• screwdrivers;
• knife (construction).

The removal of old upholstery will not take much time. The main thing is to clearly follow the instructions, step by step to perform actions and do not rush anywhere.

• Remove the door with loops.
• Dismantle the castle and the rest of the accessories.

Attention! If you consider it necessary to simultaneously replace the lock, then check whether the grooves are suitable in the door.

• Remove the upholstery layer. First external and then internal. You will need passatasi. The door is better to install in a horizontal position.
• Check if you need to update the plywood sheet attached to the door frame (if it is). If plywood is satisfactory, then there is no need to dismantle it. If you need to update the plywood sheet, the old one will have to delete. As a rule, it is attached to the frame of liquid nails. To remove them, you need to apply the thermal way of exposure. First, heat the place of attachment to hot air, and then quickly cool with ice or cool water. Liquid nails will not tolerate such sharp temperature drops.
• The dismantling of the old upholstery is made, you can proceed with the trimming material.

Upholstery Dermantine: Step-by-step instructions

After the preparatory work is completed, you can take up the upholstery door. The decoration of a wooden and metal door has some differences.

Upholstery of wooden doors

• From small leatherette or dermatantine strips to make rollers, which are fixed along the edges of the canvas with the front side. They are made empty or printed.
• On the entire surface of the door, laying the canvas heat and noise insulation, and put the dermantine on top.
• From the side of the door fastening to the loops, leave about 10 cm. The edges will be subjected to decorative cloves with a step 7-9 cm. Near the loop, the finishing material is nourished in the latter queue. Create a roller, which is naked to the jamb.
• So that the thermal insulation material inside is not deformed and did not fall away, Dermantin needs to drag the cord and navigate with small cloves.

Council. With the help of a decorative cord on the door, you can create various beautiful patterns.

Upholstery of metal doors

The decoration of the metal door is somewhat different from the wooden: it is performed faster and easier, since there is no need to fix dermantine decorative nails.

• The door is placed in a horizontal position and lubricate its surface with glue.
• Thermal insulation material is placed on top and slightly pressed it to the surface. When the glue is grabbing, the extra material must be cut off with a knife or scissors.
• The shelves process the ends and fix the dermatin on it. First, the glue is fixed by the upper part of the finishing material, then the bottom. Watch that Dermantin does not bother or harmonica.
• After complete drying of the glue, the surplus is cut off, and the door is hung back to the loop.

• The door surface can be decorated with a cord, but without the use of carnations. For its attachment apply glue.

Upholstery Dermantine door or other finishing material is not such a difficult matter. Qualitatively performed upholstery will not only update the appearance of the door, but also will last for many years, and will also improve thermal insulation in the apartment.

How to hide Dermantine doors with your own hands: Video

Door upholstery: photo