Structural painting of walls. Structural paint for walls

Structural painting of walls. Structural paint for walls - advantages and features

The use of painting for wall design and ceiling is a very popular solution that allows a short time to get a seamless beautiful decoration. Special beauty is distinguished by the so-called. "Textured" paints, the application of which is somewhat different from the usual material.

Under the texture paint is a homogeneous material in the form of a dense mass of white. This substance is produced most often on the basis of Acrylic, which informs it excellent characteristics and opens up wide opportunities for use. By introducing into the composition of such paint, various pigments can be achieved this or that shade of the surface. As for silicate and silicone compounds, they are less common due to their high cost and exposure to fungi and mold.

Textural paint

The advantages of the material include:

Textural paint

The disadvantages of the finish usually include some complexity of its application (compared to conventional paint) and the effect of the blockage of the room arising from the formation of a waterproof film on the separated surface.

By type of decorative effects created, textured paints are divided into the following types:

Misuri. In addition to acrylic, a modified starch is present in the substance, which allows you to receive both structural and smooth effect when applying. This or that texture depends on the stacked tool used.
Textual paint "Misuri"
Marseille wax. With the help of this paint, it is possible to achieve a very plausible imitation of natural stone and cork wood. Like Misuri, Marseille wax can give a smooth or factory effect. Justice It is worth noting that a completely smooth surface in this case cannot be obtained - the shallow depressions after smoothing still remain. To protect against moisture and an increase in decorative qualities, a layer of wax is applied to the dried surface.
Textural paint "Marseille wax"
Atacama. The material has outstanding external qualities: the finish plays numerous colors when viewed by it from different sides. Such an effect is achieved thanks to the composition of the paint of quartz sand and special metallized additives forming a reflective layer. It seems and when touching the finish creates a feeling of velvety.
Texture paint "Atakama"
Relief. Acrylic components in this case are reinforced by quartz sand and a number of other substances, which makes it possible to create pronounced patterns. To create a smooth surface, the embossed paint does not fit. It is this option that the finishes are considered the most vivid representative of the texture paint.
Texture paint "Relief"

This stage is very similar to the preparation for applying usually with water-emulsion paint. However, due to the greater viscosity of the textured composition of the strength requirements, the foundation in this case is an order of magnitude higher.

Operating procedure:

Preparation of the room. Repair activities of this type are accompanied by the formation of a large amount of dust and dirt. Therefore, it is recommended to fully free the rooms from all the furniture and decor items, remove chandeliers and lamps. Those items that, because of their dimensions, do not take place, should be shifted to the center of the room and cover the film. Also, polyethylene is covered with the entire area of \u200b\u200bthe floor (if the finish floor finish has already been laid).
Okaddka old finish. Walls and ceiling (if it will also be separated) purified from the whole old finish. Ideally should remain bare panels or plaster. All fragments of the draft base, which are badly held and vibrated when touched, must be discarded with a hammer or pick. The sacrificed surface is thoroughly impregnated with primer.
Stucco, putty. After drying, the primer is applied with an aligning layer of plaster or starting putty. As a rule, the walls are aligned with plaster, and the ceiling is putty. At this stage, it is important to achieve visual smoothing of all irregularities, for which you can use the rule and lighthouses. If the base is mainly even, immediately carry out the finishing putty (in 2-3 layers).
Grinding. Having waited for a complete drying of the last layer of putty (it usually takes no less than a day), grinding with painting sandpaper (№120-140). If subsequently, it is assumed to use decorative paint, which forms the texture, when grinding can be condescendingly related to small scratches: on the finished surface they will not be noticeable.
Finish primer. A very responsible stage, as it is important to achieve the most equal thickness of the primer layer throughout the area of \u200b\u200bapplication. Otherwise, the finish finish will contain irregularities. As a material, it is recommended to use an acrylic impregnation, missing the base of 1-2 layers. Pause on the drying of one layer - approximately 6 hours.

Before applying texture paint, you must carefully read the attached instructions. There is information about the time of drying, the order of preparation and recommendations for applying. The material of this type usually goes on sale in plastic buckets.

Textural paint

The consistency of the structural composition is characterized by a decent density, so it is added some water before applying it and stir the mixing drill. With water, it is important not to overdo it, because Too liquid substance simply will not be held on the ground (this is especially true of the ceiling). According to the recommendation of specialists, the volume of the water added should not exceed 1/10 of the total. As practice shows, it is usually enough for stirring on average 4%.

Adding water to texture paint

If on the design idea, the stained surface should have a different color (not white), the corresponding pigment is introduced into the paint. It is best to entrust this procedure to professionals in the store where the material is purchased. With independent coloring paint, it is important to observe greater attentiveness, introducing a pigment substance with small shares.

Adding color pigment to texture paint

After each portion, you need to pause for mixing and checking the resulting shade. If its intensity is insufficient, the procedure continues on. Checking the level of color intensity is carried out by applying paint onto the wall (to accelerate the drying of trial smears, you can apply a hairdryer). The best quality of pigmentation is achieved when using the Koller of the same company as paint.

Mix colored pigment with paint

Turning directly to painting the prepared base of the wall or ceiling, a competent organization of lighting will be required. The fact is that the visual perception of the finished textured surface depends largely on the angle of falling and the intensity of light. Therefore, in order to achieve the desired decorative effect, it is important to create the same lighting conditions that will be in the room during its operation. Material for painting it is necessary to put in the room for about a day before the start of work.

The texture paint can be applied in several ways, which depends on the specifics of the final result:

High decorative characteristics of textured paints give a wide space for the flight of creative fantasy.

A number of options for additional surface paint surface can be applied:

Trowel. In the presence of sufficient experience, you can achieve the creation on the ceiling or walls of full-fledged art compositions. Most often for this, the technique of smears is used: instead of a brush in the hands of the artist in this case there is a Kelma.
Collective paint application
Stencils, sponges, stamps, etc. To post a homogeneous surface of additional decoration, you can use in advance stencils or sponges. The imprint is applied to another raw material, so it's better to work in such cases: one person makes paint with a roller or a spatula, and the other trail is on the surface additional prints.
Paint sponge paint
Graters, scallops. Used to scratch the surface (such a reception is characteristic of creating the texture "Marseille wax").
Azure. Using this material, the painted surface of the ceiling or walls is drawn up with an additional effect. It may be shine, gloss, pearl, etc. To do this, you will need two-layer lazuries with a short pile roller or a painting brush. Also used to use the pre-moistened and pressed natural sponge. Saving it into the mother of pearl azure, decorate the foundation of circular movements. To increase the disclosure of the resulting drawing, the sponge is more crushed and scrolled.

To protect the adjacent surfaces from the ingress of paint, the borders of the separated area are punctured by painting scotch. In the absence of experience, it is not recommended to immediately take for the design of open ceiling or wall sections. It is better to choose to pre-train the place on the wall that will later be closed with a cabinet. Given the thickness of the texture paint, its complete drying lasts for several days.

How to apply texture paint: instruction with photos and videos

Exquisitely and tastefully decorated walls are a very important element of the decor to place any destination. Almost all existing finishing materials have some disadvantages that limit their use, especially in the interior, which require not only beauty, but also safety and environmental friendliness. Therefore, the optimal material for the inner, and the outer decoration of the wall is the texture paint. Only it allows you to create incredibly chic, fascinating surfaces on the walls, allowing any manifestations of your own, even richest and irrepressible fantasy.

The process of working with textured paint is distinguished by incredible simplicity and ease, so it can be used by people with a complete lack of experience in building and finishing work. A distinctive feature of the work carried out on coloring can be considered the possibility of creating their own textures, as well as sufficient time to correct what I did not like or did not work out. For the extent of "skill", it is possible to practice on a piece of plywood or a small segment of the wall (in this case, the main staining of the "training" composition of the texture paint should be completely removed by the steel spatula, and the wall is dried and primed).

The texture paint for walls has undeniable advantages over other materials, and among the mains can be distinguished as:

frost resistance;
resistance to constant influence of UV rays;
the plasticity of the resulting coating, which does not allow the wall to be covered with small cracks (with natural shrinkage of buildings);
insensitivity to dampness, preventing the formation and reproduction of fungus;
the finished surface does not absorb smells at all;
dust-absorbing properties that facilitate subsequent care;
high ecology, which gives the possibility of use in children's;
the possibility of using on any bases - from brickwork to wood;
huge scope for creativity with its independent application.

In addition, it is worth noting its hypoallergenicity and minimum requirements for the quality of the surface used to apply texture paints for internal work.

Application of texture paint

The texture paint for walls is applied, according to reviews, extremely easy, and the use of any complex special tool is not required. Textured paint for walls with their own hands can be somewhat modified, which will allow you to create your own, unusual textures. So, to obtain a rude embossed surface, it is possible to add pure wood sawdust to the paint, and quartz sand is added to the preparation with sharp edges. The paint is applied a sufficient thick layer, so all the cracks available on the wall on the wall, chips and small irregularities.

The choice of tools for applying is deprived of any standards, and depending on what effect you want to achieve:

natural sponge;
fact (structural) roller of different length and diameter;
comb;
putty knife.

In general, the application of texture paint is possible even by hand, since it is absolutely safe, and the decor created by the "manually" can become quite unexpected, interesting and unique.

A little about applying textured paint roller shown on video

Options for possible reliefs

The textured painting of walls of water-emulsion paint allows you to get several basic textures.

Stages of work

The application of texture paint with roller, of course, does not differ in any particular complexity nor laborious preparation of the surface - and this is its huge advantage. However, the minimum work of the work will still need:

it is advisable to catch the wall with a hammer, which will allow to identify areas where the old plaster is about to be ready (this is necessary to eliminate);
large cracks need to be seen;
the entire surface intended for the color of the walls in the apartment paint apartment should be trusted by acrylic primer, preferably marked with "deep penetration".

Tip! The best results are achieved when the composition is applied and the base has room temperature.

Before working with such paint, it requires a very thorough mixing, and it is better if a drill with a macker will be used for this. Re-stirring is necessary after adding the selected filler and the flaker. There are several mandatory rules, otherwise the effect may differ from the intended:

the application of textured paint should be carried out a sufficiently thick layer in order to create a conceived invoice;
it is advisable to work immediately on the entire surface, where the texture will be created, since the "joints" may be noticeable during interruptions, which visually worsen the impression of all work;
the tool that is planned to be used must prepare in advance;
after drying, the textured formulations for walls with effects can be additionally stained with acrylic compositions.

Choose optimal texture paint

Painting the walls of texture paint allows you to get a unique, exquisite interior. With this, now nobody argues. But in some cases, people complain that instead of unprecedented beauty, it turned out absolutely not what they expected. In almost every such fact, buyers who did not have a clear idea that ultimately wanted to get was to blame. If it is more or less understandable to work with texture paint more or less understandable, then a few inflicts know a few.

Each coloring composition for giving the wall of texture and relief has its grate. The more pronounced and deep invoice requires, the greater grainity should be chosen, and since this parameter is marked by each manufacturer in its own way, you should not neglect the consultation of the seller when buying. Another important parameter of textured coatings is the basis.

Mineral. The most budget option consisting of cement and lime, and manufactured in the form of a dry powder. Most often with the help of mineral composition, the texture of the outdoor walls of the buildings attach.
Silicone. The most common option that can be used both inside and outside buildings is. Creates a vapor-permeable coating, resistant to moisture, temperature drops and aggressive environments.
Silicate. The most expensive, but very practical option. This coating is not terrible any effects of the atmosphere, the surface being processed does not absorb dirt and dust, easy to care. Use is allowed only in a complex with primer on a similar basis.
Acrylic. The most convenient, ready-to-use composition, which allows the tinting and the introduction of the required fillers.

Empodially engaged in creating a new, creative interior of his own home, should not forget that in any case it is necessary if not experience, then at least a skill, so before work is needed training. In addition, it is pre-necessary to predetermine which surface is required to get. To do this, you can not only watch online photo gallery, but also try to draw your future interior.

You can apply texture paint to a separate area, and using various tools or remedies to see which texture is obtained. It is important to understand that the pattern that looks good in a small area may be inappropriate on the whole wall. In addition, you should not forget that all the tool used to work with texture paint should be clean. Naturally, it is impossible to neglect the elementary safety requirements - do not interfere with the means of individual protection and sufficient ventilation of the room.

Texture paint for internal works, reviews, photo
Parquet varnish two-component, acrylic, matte and glossy
Heat-resistant paint for metal do it yourself
Paint types for children's room: Magnetic, Dulux, Tex, Profi

Types of textured paint for walls, application technology
Decorative painting of walls do it yourself, textured
Textural paint: Creative design with your hands
Tractor paint for ceiling: video instructions
Painting the walls of texture paint do it yourself How to make texture plaster walls

Properties of structural paint

Structural (relief) paint is a relatively young species of decorative surface finish. It is a dispersed mixture, which includes the inclusion of elements of various structures. To use this method of decorating steel quite recently, however, it has already gained great popularity, due to the relatively simple technology of application and excellent results.

Many appreciated the originality and effectiveness of the coloring composition, as well as the practicality and environmental friendliness of this material.

Structural paint has a unique property of passing steam, ensuring the maintenance of the perfect balance of temperature and humidity, which makes it ideal for use during internal works.

At the same time, this composition is extremely resistant to the effects of the external environment, so the paint can be used without fears for facade and outdoor work. The service life of such a coating is up to four years.

Structural paint gives surfaces relief and creates additional protection against mechanical or atmospheric effects.

In addition, the structural composition has excellent clutch with the surface, so such a coating is successfully used to decorate the walls, and, most different, starting from concrete and, ending with wooden.

The advantage of structural paint is the wide color scheme of the coloring composition, it is not possible to choose the right shade will not be much difficulty. And, of course, the undoubted advantage is the unique individual surface design when working with this material.

Of the cons of the use of structural paint, it can be called a relatively high cost of painting composition.

Although the technology of its use allows us to cover the surface with only one paint layer, which will undoubtedly reduce the required amount of coloring composition for work.

Use the structural paint in decorating the room is quite simple. It is not necessary to have special professional knowledge in painting business.

To decorate the surface, in addition to the painting composition, you will need:

metal brush,
master OK,
mcList
putty knife,
rolls with fur or foam nozzle.

The decoration process consists of a series of consecutive actions.

Technology textured painting of walls with their own hands

First, they prepare the surface for applying the coloring composition, after that it is ground and, if necessary, apply a layer of acrylic paint of the desired shade. Then the coloring composition is prepared, thoroughly mixed and contained into the appropriate color. Only after that you can move to applying paint to the surface.

Consider the nuances of the use of structural paint during the decoration process.

Applying structural paint

Preparation for staining begins with pre-processing of the surface. Despite the pretty simple application of the paint composition itself, it is required to pay special attention to the preparation of the basis for decorating. Otherwise, the service life will be significantly less.

Structural paint wall

Surface preparation

If the surface was plastered without reinforcement, it would be nice to remove the layer of plaster completely.

With a strong clutch of the layer of plastering with the wall, there is no need to remove it completely, it is enough to remove poorly holding areas of the solidified solution. In addition, it is necessary to remove the irradiated and peeling paint, for which it is possible to richly moisten the surface with water, and after a while he dried a plot with a construction or ordinary hairdryer. Water that fell into microcracks in the layer of paint, with a drying, an old coating will swell, which is easily cleaned with a spatula or metal brush.

It is allowed to apply a coloring composition on an old layer of paint, however, in this case, the entire surface must be treated with a grinding machine or sandpaper, and the old layer should turn out to be matte.

If there is no need to eliminate them on the surface of small defects.

Structural paint can cope with this task, as a relief pattern is created during the decoration. In the case of significant irregularities, the base should be sharpened.

Applying primer

To ensure high adhesion, the surface should be thoroughly projected.

In this case, the primer layer will not only remove small particles of dust and dirt, but also provide a high-quality basis. For the primer surface, it is more convenient to use a foam roller, and hard-to-reach places can be treated with a brush.

As a primer material can act acrylic.

It is simple and easy to use, unpretentious and affordable.

The primer performs a very important function to protect the subsequent layer of structural paint from physical, chemical, mechanical exposure and, at the same time, increases the coating service time and saves material.

Mixtures of deep penetration are also well suited as primer material.

Best, according to specialists, use special primer formulations.

It should be proceeding to directly applying structural paints to the surface only after a complete drying of the primer layer in about 2-3 hours.

Preparation of the room

Before performing painting works in the room, it should be taken in advance that there are no drafts there, direct solar rays should not fall on the surface, and the optimum temperature in the room for high-quality drying composition should be from 25 to 30 degrees of heat.

Painting structural paint

Before using the coloring composition, it is necessary to mix thoroughly if the consistency of the paint is too thick, then it can be diluted with conventional water or a special solvent.

Also at this stage, the coloring composition is a member, giving it the desired shade.

It is necessary to apply the paint to the surface with a thick layer, at least two centimeters, it is due to a wide layer of paints the surface will acquire an exquisite embossed form.

Cover the paint surface with a preferred spatula.

It is important to remember that the structural composition is applied to the wall no more than one layer.

The coloring composition on the surface should be applied evenly.

In case the large surface area is decorated, it is advisable to apply material on planes. In this case, the surface of the plane must be painted completely in one reception. If you do not use this method, then the discrepancy between the color gamut on the surface of the surface is possible.

Surface decoration

The next stage is one of the most pleasant to implement designer ideas.

Using a fur roller or brush, you must give the coating your unique pattern or drawing. Creative thought here is absolutely not limited. Creating a unique pattern on a wall using a roller has its own characteristics, for example, the design technique on the wall may be longitudinal, transverse and even combined.

You can give the surface "scratched" relief with the help of metal brushes or scallops. If you wish, create a smaller and elegant relief, fur roller or brush enough to pre-slightly moisten with water.

In a word, at this stage you can safely experiment with various techniques for choosing the surface of patterns and drawings.

The coloring composition is very quickly thick and starts to dry after half an hour, so you need to create patterns or patterns on the surface immediately.

By the way, it will take from eight to twelve days for complete drying, after which it can be cleaned, washed or subject to other impacts.

When applying the coloring composition, the roller needs to perform a number of conditions.

First, the number of rollers should be at least three, with two rollers must be of the same size, and one is somewhat less. In the process of decorating the surface, two tools of different sizes are involved. Secondly, the tool must be fully immersed in the coloration bath and cover the surface with vertical lines from top to bottom.

And finally, the material should be applied gradually, first a large roller, and, then, if it is necessary to correct the shortcomings, a roller with a smaller size is used.

Finishing stage

At the end, you need to check the uniform of the applied layer of the coloring composition, if it is excessively thick, then a pure roller is useful here, with which you can remove the surplus paint from the surface.

After creating a relief pattern on the surface, the coating can be finalized, namely remove the sharp edges of the texture surface with a brush or spatula.

Naturally, in order to obtain an ideal result, the coloring composition of one batch should be used to withstand the uniform tonality of the entire surface, as well as when diluted with paint, it is importantly important to use the same source or composition.

Application sprayer

There is another technology for staining surfaces by structural coloring composition.

It consists in using a sprayer as a tool for applying material to the surface.

The advantage of this technology is the ability to adjust the size of the particles of the coloring composition, as well as the intensity of the feed and the consumption of paint.

Together with a magnificent textured effect, the use of the pulverizer gives an impressive result.

Another advantage of the use of this method is the possibility of its easy use, both internal and for external work.

If the device is properly adjusted, then when painting, the perfect layer of coloring composition without flops will be obtained. The distance from the pulverizer to the surface of the surface should be from 50 to 70 centimeters, in this case the particles of the coloring agent will evenly fall on the surface.

At a smaller distance, the paint layer can not lie down at exactly, moreover, the consumption of material will increase significantly.

If the distance from the surface to the sprayer will be too large, a portion of the coloring substance is simply mounted on the floor. The movement of the pulverizer should be smooth without jerks, besides, it is impossible to linger on one site too long, the drums were not formed.

When staining outside the room, it should also be remembered that the impact of direct sunlight on structural paint reduces its service life.

A freshly detected coating should be protected from drying out of drying out of excess moisture and low temperatures, for this you can use a foil or mesh bedspread.

Structural paints give the surface a unique texture, simultaneously protecting it from atmospheric and mechanical impact and allowing the most courageous creative ideas to decorate the interior.

Video of structural paint

To date, there is a huge number of different materials in the construction market and one of the most popular is the paint with the effect of sand. In our review, we will tell you in detail about everything that is connected with such paint.

The main composition of decorative paint with sand

2. Types of paints with sand effect

3. Application technology

4. Benefits

The main composition of decorative paint with sand

Today, all advanced manufacturers produce paint with sand on the basis of a binder - acrylic emulsion.

And naturally, the second main component is the sand itself. Third, which will affect the properties of the material - these are additional pigments to give the basis of the material of certain visual properties. Now let's stop at all these parts in more detail.

Acrylic emulsion - serves so that the grain of the sands clung to each other and the paint itself adhesive against the wall. If the acrylic is used low quality - then the grain of the hand, if you spend the hand on the painted wall - shivered and remain on the palm.

High quality raw materials does not allow the sands to fall off and, accordingly, you are many more chances that the coating will last long. After all, the average service life of decorative paints is today about 20 years.

Now sand.

We see again that there are manufacturers of high-quality materials and there are those who seek to reduce the product to the detriment of quality. How to determine - what sand is qualitative or not? There is also an easy way - sand, after applying, should be visually homogeneous and small. Large sand is of course inogee can be beautiful, but the thin layer of paint will not hold it and over time, such a coating will be fused and will lose an attractive appearance.

And the homogeneity of the sand says that the crude sand was worked out by the separator and garbage and impurities were removed from it. In some paints with sand you can find small glass sand. Such materials have a 3D effect and from them you can create various decorative effects - the sea, suede, etc.

The latter of important parts is pigments.

Today there are matte sands on the market, with a silver base, gold or chameleon. The 3D sands described above have a transparent matte database.

Types of paints with sand effect

The various types of decorative paint coatings with sand will be determined by both paint composition and the way it is applied.

Based on the above formulations, we have several types of coatings - these are classic sands (matte, gold, silver), paint with a velvet effect (this is when sand is a lot of sand and it gives the effect of velvet), paint with 3D effect (this is the option When the composition is used round glass grains), paint with the effect of chameleon (this is when at a different angle of falling the light of the form, the substrate is under the sand, then the base of the paint).

Applying various types of applying, you can create absolutely different coatings from the same paint.

You can make the effect of sandy vortices, and you can the effect of coarse burlap. You can apply vertical lines - so-called. The effect of the rain, or to arrange them horizontally or under the tilt.

Still, recently, a popularity is gaining a popularity of the sanding of the Celma - it turns out a smooth suede coating - as if paint with skin effect or try to apply paint with sand paint to obtain a uniform distribution of sand on the surface of the wall.

Other ways to create coatings include options for separate tinting and application - the so-called multiple colored coatings.

Either you can add a large number of coller in the paint - and then you will get a matte coating. You can also add various additives in the paint - for example, a gold or silver glitter (sparkles) to make an additional shine paint.

Another of the popular types of coatings is a combined multicomponent coating.

If various translucent materials are applied on top of paint with sand - you will receive many additional effects of such paint.

Sand paint paint technology

For the most part, all the options for sand paints are applied approximately equally.

The essence of technology is very simple:

First you need to apply a quartz filler substrate (essentially with sand). In no way, it is impossible to use ordinary paint for this, as the main objectives of the substrate is the creation of good adhesion with the wall, due to the special acrylic emulsion in its composition, as well as the possibility of creating the necessary effect, due to the quartz substrate.

The substrate on the wall is applied evenly with a roller or brush. If you are going to buy paint with the effect of sand at a quality producer, then the substrate does not need to be composed, since high-quality materials are applied in one layer and have good covers. An exception occurs when the substrate is used as creating a color in translucent paint with sand.

Then, after drying the substrate, it is necessary to apply paint with sand with a brush or lymat, depending on the result selected and give the coating the necessary appearance.

On this all technology ends.

The subtleties of the process of applying texture paint

One layer of substrate plus one layer of paint, all saying to do the rest is just a desire to sell low-quality material more and work on appreciation.

Benefits of Paints with Sand Effect

Paints with the effect of sand have a number of advantages over other materials.

First, this is the possibility of creating a large number of different visual effects. In essence, this is a designer, where you can create different coatings in different rooms from the same material.

The second explicit advantage is its wear resistance. All coatings made from such paint can be easily used even in public premises due to their positive characteristics for abrasion resistance. But once again declare - in this review we are talking about quality materials.

Additional advantages will be the safety of this health paint (it is especially important to make sure that you bought material with a certificate of safety A +), the content in the composition of the paint of fungicides prevents the formation of mold on the walls and the most important thing - the application of such paint refers to one of the easiest - then There are even you yourself, a little learning, you can create a stylish and beautiful interior in your house.

Buy Paint with Sand Effect can here, in our online store of decorative plasters in Moscow

Hair dyeing house

It is known that the change of image is the best way to improve your mood, start a new life or to draw attention to others.

So, you finally decided to repaint hair. Now your main task is to choose a suitable paint, and then properly apply it on your hair to get the perfect result.

For the very first staining, the unstable paint is suitable, for example, a tinting hair foam, which is washed after several head wash procedures. Do not strive for sharp changes, it greatly hurt hair.

Do not try to do something supernatural. Leave radical changes to professionals.

Having bought in the store paint, we begin with anticipation, coming home, quickly open it, wear gloves, mix bubbles and apply on hair.

This process for most of us is brought to automatism. And in vain, because first of all, you need to carefully read the instructions.

There are two gross misconceptions: the longer we keep paint, the more efficient the color will take, and the more paint we apply, the more intense the color will be. The first definition is incorrect due to the fact that, overwhelming the paint in time, you can drain them, or even squeeze. The second is the trick of the sellers, so you take more product packages.

1. How to apply paint

1. Before the first staining of the hair, the head should not be washed, so as not to remove the protective film with the scalp. Paint and so deeply absorbed into the hair.

2. Apply paint on dry curls.

3. Before staining, apply protective cream or vaseline on the skin of the face along the hair growth line, on the forehead and whiskey so that the skin does not change the color.

4. Be sure to put on gloves.

5. Divide your hair on thin strands and evenly and most importantly quickly - apply composition on them with a brush: from the occipital part towards the temples, evenly processing them from the roots to the most tips.

6. If difficulties arise in the distribution of paint along the entire length of the hair, slightly moisten them with warm water. The paint will become less thick and easier to distribute.

7. After all hair is processed, it is thoroughly tailored to their comb with rare teeth.

8. Immediately after applying, erase the residues of paint from the skin, not forgetting about the neck and ears.

9. Leave paint on the hair for 25-30 minutes (according to the instructions), without covering the head. If gray hair is too much, increase the time for another 10 minutes.

2. Wash the paint

After staining, foaming the painting emulsion with a small amount of water, after which we thoroughly rinse warm water.

Textured paint for walls how to apply video

Fixing paint, make sure the hair was washed to the end. You can rinse with shampoo hair to remove the coloring elements then rinse the air conditioner. The one that was included, and the one you used to.

Hair after staining especially need protection and care. To preserve the resulting color, its juits and brightness, it is recommended to use balm for painted hair.

Results of coloring

In case the painting passed unsuccessfully, it is best to contact a specialist. Even if you wash your head in a row ten times, the paint will not come down.

The most incorrect solution will be a sharp repainting back to the previous color. The hair is already injured, and only a professional can help not only return the beauty of her hair, but also to protect them from damage.

The main thing - do not forget that the cardinal change in the color of the hair is very strongly affected by the state of your hairstyle: the hair can start not just enter or require more careful care, but even fall out.

It would be nice for the future to write the paint number that you chose, and do not forget to spread the towel on the pillowcase to avoid stains.

This is especially true if you are brunette.

Tinting the resulting roots

When tapping the roots of the hair, make the composition first on the roots, starting with the occipital part.

After 20 minutes, distribute the remaining emulsion along the entire length of the hair to the most tips and tail the hair so that the paint is distributed evenly.

Leave the composition for another 10 minutes then wash off.

Necessary subjects for those who decided to paint hair at home

So that you have as little difficulties as possible, you need to have the following necessary items at hand:

No way do without gloves.

Follow the extra pair, suddenly in the process staining those attached to the paint, we will break, then you can blur not only hands, but also clothes. It is best to fit gloves without talca, not irritating the skin.

A brush will help gently and accurately apply paint. You can not regret money and purchase professional, it is especially convenient.

Especially since it is useful for you more than once.

Plastic or glass bowl for mixing paints and just to facilitate the process.

Clamps for hair and crabs to share strands. Choose only plastic hairpins.

Clock to measure time.

Old t-shirt or bathrobe. Even if you are blurred, it will not be a pity.

And also come in handy towel.

Precautions

When dyeing hair at home it is impossible: use the purchased emulsion is not for the purpose, neglect gloves, make a chemical twist before or after staining, carry out the procedure if there are wounds on the skin of the head, scratches or abrasions, apply the drug on hair painted by natural dyes exceeding the specified on Packing time, store and use a secondary cooked emulsion

Lamination Hairwood for painted Hair-colored Hair color in color - Summer, autumn, winter, Springamine is always in fashion! Biosavka: We restore Hair hairstyles for long hair accelerate hair growth? Hair shine - like in a glossy magazine!

Textural paint decor: types of wall reliefs, applying methods (photos, video, reviews)

Structural paint for walls roller: video instruction on coloring with your own hands, features painting, price, photo

Structural paint is an excellent finishing material that has recently been actively used when performing repairs along with wallpaper and other finishing materials.

Its application is performed quite simply and does not require any professional skills, however, with some nuances of work still one should read.

Painted structural paint surface

What is structural paint

First of all, we will figure it out that it is a structural or, as it is also called, texture paint. And it is externally, it is a thick and viscous white mass.

Despite the fact that the material is called paint, in its structure it is more like plaster.

After applying this composition on the wall, it attaches a certain structure using a roller or other tools.

Structural paint ceresit

Advantages of coating

It must be said that the increasing popularity of this finishing material is fully justified by a variety of advantages:

The coating has good vapor permeability, due to which natural moisture exchange is not disturbed.
The dense structure of the coating allows to hide minor flaws in the roughing of the walls, so there is no need to bring the base to the perfect state.
Since structural plaster initially has a white color, it can be given any necessary shade with special colors.
The coating has a high moisture resistance, due to which the material can be used in rooms with high humidity.
And in the case of pollution of the walls, they can be cleaned using water, without fear damage the surface.
High wear resistance.
Resistance to the effects of ultraviolet rays.
Elasticity.
Ecology and harmlessness in the process of staining surfaces.
If necessary, you can change the color of the finishes at any time, covering it with acrylic paint.
Universality - the coating can be used not only inside, but also outside the room.
The paint is allowed to apply on concrete, brick, plasterboard, plastered and swept surfaces.

Tip!
When staining the composition, it is desirable to use the kel of the same manufacturer as the texture paint itself.
This will make it possible to get the highest quality result.

Color for structural paint

disadvantages

Of the disadvantages of the material, you can note only that the price of it is quite high.

However, given the durability of such a finish and its wear resistance, as a result, the savings are still obtained.