All secrets of the screen installation on the acrylic bath. Mounting features for rectangular corner models

Bath Installation Requirements

Installation of the bath should be made only by qualified specialists, in compliance with the following requirements:

Installing a bath without a frame, and also with a modified frame is not allowed. The legs serve to exhibit the bath at the level and adjustment of the gap between the bath panel and the floor. The bath should be based on all the points of the supports to eliminate the uneven load distribution and, as a result, the appearance of the microcrack of the bath case;

It is not allowed toasting the bath in the tile, panels or rigid building solutions. In order to avoid moisture from entering the bath or on hydromassage equipment, the seams between the bathroom and the wall must be sealed with plumbing silicone.

Avoid moving dirt and building dust on the surface of the bath. This may be the cause of clogging and failure of hydromassage equipment or lead to the appearance of scratches on the surface of the bath, upon subsequent non-professional cleaning.

When performing work on the withdrawal of water supply and sewage pipes, the linear dimensions of the bath must be taken into account. Otherwise, the connection may be difficult, since the outputs of pipes may continue to the ribs, units and fittings of the bath, and the bath will not be able to be installed close to the walls. Constructive changes in the location of the equipment and pipelines of the bath, trimming the fastening clamps and so on is categorically prohibited.

The wiring of the room must have an individual differential switch 30mA, a magnetotermo 2,4-4a or other general compound (CEI-64-8) and installed in the overall room shield. It is strictly forbidden to install the specified switches under the bathroom!

Before starting work it is necessary to check the completeness of the product, cocasium, screen.

ATTENTION! Failure or fulfillment of the above requirements does not provide for the preservation of warranty maintenance or repair conditions for such a bath.

Installation of bath

Install the bath on the legs (Fig. 1) by the manufacturer's company is allowed to complete the legs with a bolt M12, instead of appropriate threaded studs. Feet of configuration A (Fig. 1) (2 pcs.) - installed with the front (front) side of the bath, along the edges, on the left and right (for the Riviera bath - 4pcs., All in front). Feet of configuration B (Fig. 1) - Other remaining front and rear legs. Attaching the legs to the frame is made by the top pair of M12 nuts, which also serve to adjust the bath in height. Place the bath of drainage-overflow (Fig. 2), siphon (may not enter the kit), and adjust the bath in height. The distance from the floor level to the lower point of the siphon should be at least 15 mm. Make sure the bath is adjusted and rests on all the points of the support. Install the panel on the bath, snapping it on top mounts (Fig. 6 and 7). On some models of symmetric and asymmetric baths "BAS", it is possible to cut panels in length (no more than 2 cm per side). In addition, if the side panel is planned to install on your bath, then you first check the upper mounts running with the side panel in the kit. Adjust the vertical panel. The bottom of the panel should be seamless to the plane of the pinching corner installed on the extreme legs. The depth of planting angle is regulated by the bottom pair of nuts M12. Corners must be equally among themselves adjusted in height, and be symmetrical relative to the panel. The drill of a diameter of 3.5 mm (the size is specified for the 4.2x25 mm screw) in the lower corners and the cross-cutting holes (Fig. 4 and 5) in the lower corners. Remove the panel from the bath and make it connect to the sewage and water supply systems (see the bath connection to the water supply and sewage network), as well as to the 220 V electrical network (see the bath connection to the electrical network). After that, gently move the bath tightly to the wall, and make sure that it is stable at all points of the support, and all connections are done correctly. Install the panel on the bath and fix it in the drilled holes with a screw with a press washer (Fig. 8).
Close the hats of self-drawing with a decorative plug (Fig. 9).

ATTENTION! In order to avoid moisture from entering the bath, make the obligatory processing of the seams by Plumbing Silicone throughout the perimeter of the fitting of the bath!

Bath connection to water supply and sewage network

Bath connection to the water supply and sewage network should be made by a qualified plumber. The bath kit includes a semi-automatic drainage device, which, after it is installed on the bath, connects to the sewer network stationary, through a flexible corrugated or rigid PVC pipe (not included). Sewer drain diameter 40-50 mm is displayed at the place of installation of the bath in the floor or wall, taking into account the linear sizes of the bath. When the plum is located in the wall, the optimal height is considered a distance of no more than 2 cm from the floor level to the lower edge of the pipe. Connecting the bath to the water supply network in case it is equipped with a mortise mixer. The network pressure should be 3-5 atm. With a pressure of more than 5 atm., Pressure gearboxes should be installed and adjust them to the specified norms.

Places for connecting to the water supply system should be placed taking into account the linear sizes of the bath and its units and are equipped with disabilities from the main mainstream of the cranes. Connecting to the system is carried out through flexible plumbing lining (tap hoses). The length of the hoses should allow the displacement of the bath from the walls and the distance of at least 0.5 m. It is recommended to use water purification filters. The absence of filters can lead to clogging of hydromassage nozzles and insertion in the ceramic cartridge of the metal hydral mixer, which will lead them to failure.

Operation of baths "BAS"

Thank you for buying a BAS brand bath. Bas hydromassage baths are modern technologies and original lines that ensure the comfort of hydromassage, which will strengthen your health and will give a lot of pleasant minutes.

This manual describes the functions of the baths, installation requirements, care and method of operation.

Precautions

In order for the bath to bring you benefits for a long time and reliably worked, a number of conditions must be performed:

1. If your body has a violation of the cardiovascular system, then consult your doctor (in which hydromassage is useful to you).

2. Provide the installation of filters (for water purification) - it will increase the life of your mixers and hydromassage bath equipment.

3. Do not turn on the hydromassage without filling the bath with water.

4. Do not align the baths into the tile, panels or rigid building solutions, restricting access to hydromassage equipment that prevents the bath running at a distance of at least 0.5 m from the wall.

5. The bath is connected to a network of alternate single-phase current with a voltage of 220V. To avoid electric shock, the bath must be grounded through a socket with a connected grounding contact.

Technical description and equipment

Standard bath equipment is given in the following table.

№N / N.	View of components	Lists of configuration and quantity, pcs
№N / N.	View of components	A.	B.	C.	D.	E.	F.	G.
1	Acrylic bath (frame, upper panel locks and additional equipment)	1	1	1	1	1	1	1
2	Bathing (plum-overflow) with siphon \\ without siphon	1	1	1	1	1	1	1
3	Studpiece Threaded M12	4	6	6	8	7	5	7
4	Bath leg PVC M12	4	6	6	8	7	5	7
5	Corner for fastening the panel	2	2	3	2	2	2	4
6	Clip decorative (with press washer)	4	4	6	4	4	6	8
7	Washer M12x36x3,4	4	4	6	4	4	4	8
8	Nut M12.	12	16	18	20	18	14	22
9	Screw mounting 4.2x25	4	4	6	4	4	6	8
10	Manual	1	1	1	1	1	1	1

List of configuration A. -For bathing models "Cameron", "Lima", "Tessa", "Verona", "Ibiza", "Breeze", "Alegra", "Vectra", "Maldives", "Style", "Sagra", "Atlanta "," Neptune "," Malta "," Akhin "," Florida "," Fantazi ";

List of configuration B. -The bath models "Indica", "Jamaica", "Laguna";
List of configuration S. -For bath models "Capri";

List of configuration D. -The bath models "Fiesta";

List of configuration E. -For baths of the "Nicole" models;

List of configuration F. -For baths of Riol models, "Hat", "Iris", "Imperial", "Mega", "Firewood";

List of configuration G. -The bath models "Riviera";

Additional equipment include: hydromassage, back massage, Shiatsu massage, aeromassage, backlight, chromotherapy, Cutting and handle mixer control panel.

Depending on the model of the bath, the manufacturer contains panels (screens) for baths (frontal, side), shower curtains and headrests that are not additional equipment and are not included. The manufacturing company reserves the right to make changes to the design and package of baths.

Transportation of baths

The bath must be transported only in a horizontal position. When transporting and installing the bath, care should be taken to not damage the system of pipelines and electrical equipment. You should move the bath only for the housing or frame. It is necessary to avoid mechanical damage to the bath case, panels, and also eliminate the possibility of influencing chemically active reagents on the surface of the product. When transporting in the cold season, before installing, the bath must be withstanding at room temperature at least 6 hours.

ATTENTION! It is strictly forbidden to move the bath for pipelines, nozzles, handles and other equipment! Inspect the goods for compliance with the order, the lack of mechanical damage, completeness, the availability of accompanying and warranty documentation.

Bath Installation Requirements

The room in which the bath is installed must comply with the following requirements:

Tile and finishing works must be completed;

Easy access to nodes and bath assemblies should be provided for its preventive warranty service and repair;

The presence of electrolynees with the required parameters and sockets with a connected grounding contact. The power supply of the bath connection should be carried out with a double insulation electrocabolic, cross section of at least 2.5 mm2 and is in accordance with the norms and standards of the UES;

The presence of water supply and sewage. The sewer tubing of the bathroom should not rise above the floor at a connection point by more than 10 cm. If it is not possible to ensure, it is necessary to provide a podium bath;

Bath Installation Requirements

Installation of the bath should be made only by qualified specialists, in compliance with the following requirements:

Installing a bath without a frame, and also with a modified frame is not allowed. The legs serve to exhibit the bath at the level and adjustment of the gap between the bath panels and the floor. The bath should be based on all the points of the supports to eliminate the uneven load distribution and, as a result, the appearance of the microcrack of the bath case;

The wiring of the room must have an individual differential switch 30mA, a magnetotermo 2,4-4a or other general compound (CEI-64-8) and installed in the overall room shield. It is strictly forbidden to install the specified switches under the bathroom!

ATTENTION! Failure or fulfillment of the above requirements does not provide for the preservation of warranty maintenance or repair conditions for such a bath.

Bath installation

Install the bath on the legs (Fig. 1) by the manufacturer's company is allowed to complete the legs with a bolt M12, instead of appropriate threaded studs. Legs of configuration BUT(Fig. 1) (2 pcs.) - installed with the front (front) side of the bath, along the edges, left and right (for the bath " RIVIERA"- 4pcs., All in front). Legs of configuration B.(Fig. 1) - Other remaining front and rear legs. Attaching the legs to the frame is made by the top pair of M12 nuts, which also serve to adjust the bath in height.

Place the bath of drainage-overflow (Fig. 2), siphon (may not enter the kit), and adjust the bath in height. The distance from the floor level to the lower point of the siphon should be at least 15 mm. Make sure the bath is adjusted and rests on all the points of the support.

Install the panel on the bath, snapping it on top mounts (Fig. 6 and 7). On some models of symmetric and asymmetric baths "BAS", it is possible to cut panels in length (no more than 2 cm per side). In addition, if the side panel is planned to install on your bath, then you first check the upper mounts running with the side panel in the kit. Adjust the vertical panel. The bottom of the panel should be seamless to the plane of the pinching corner installed on the extreme legs. The depth of planting angle is regulated by the bottom pair of nuts M12. Corners must be equally among themselves adjusted in height, and be symmetrical relative to the panel.

The drill of a diameter of 3.5 mm (the size is specified for the 4.2x25 mm screw) in the lower corners and the cross-cutting holes (Fig. 4 and 5) in the lower corners.

Remove the panel from the bath and make it connect to the sewage and water supply systems (see the bath connection to the water supply and sewage network), as well as to the 220 V electrical network (see the bath connection to the electrical network). After that, gently move the bath tightly to the wall, and make sure that it is stable at all points of the support, and all connections are done correctly.

6. Install the panel on the bath and fix it in the drilled holes with a screw with a press washer (Fig. 8).

7. Close the screw screw with a decorative plug (Fig. 9).

ATTENTION! In order to avoid moisture from entering the bath, make the obligatory processing of the seams by Plumbing Silicone throughout the perimeter of the fitting of the bath!

Bath connection to water supply and sewage network

Bath connection to the water supply and sewage network should be made by a qualified plumber.

The bath kit includes a semi-automatic drainage device, which, after it is installed on the bath, connects to the sewer network stationary, through a flexible corrugated or rigid PVC pipe (not included). Sewer drain diameter 40-50 mm is displayed at the place of installation of the bath in the floor or wall, taking into account the linear sizes of the bath. When the plum is located in the wall, the optimal height is considered a distance of no more than 2 cm from the floor level to the lower edge of the pipe.

Connecting the bath to the water supply network in case it is equipped with a mortise mixer. The network pressure should be 3-5 atm. With a pressure of more than 5 atm., Pressure gearboxes should be installed and adjust them to the specified norms.

Places for connecting to the water supply system should be placed taking into account the linear sizes of the bath and its units and are equipped with disabilities from the main mainstream of the cranes. Connecting to the system is carried out through flexible plumbing lining (tap hoses). The length of the hoses should allow the displacement of the bath from the walls and the distance of at least 0.5 m. Recommended Use water purification filters. The absence of filters can lead to clogging of hydromassage nozzles and insertion in the ceramic cartridge of the metal hydral mixer, which will lead them to failure.

ATTENTION!Curling faucets are equipped with a set of flexible supply of a standard sample. In case the length of the flexible liner is not enough, to connect to a system or connection between the elements of the mixer, it is purchased separately, taking into account your sizes for the connection. The manufacturer of the bath is not responsible for the nature of the configuration of the mortise mixers, for damage to the elements of the hydromassage system caused by their contamination when using unfiltered water containing rust, sand, chemically active impurities, as well as breakdowns or incorrect operation of the bath equipment connected to the system Water supply with non-standard pressure in it.

Leave a bath without supervision when filling it with water. Bath overflow water can lead to the failure of the aero-mass system, without saving the warranty operating conditions of the product.

Rotate the lid of plum-overflow around its axis or when there is a load on the bath tub.

Bath connection to electrical network

The power supply of the electrical equipment is carried out from the network of alternating single-phase current, in accordance with the table below.

Function	Voltage, V.	Frequency, hz.	Power, kWt*
Hydromassage	220/240	50	0,9-1,5
Aerome massage	220/240	50	0,7-0,9

* Power is indicated depending on the bath model

Bath connection to the electrical network should be made by a qualified specialist with the 3rd and higher admission group. Order connection of hydromassage baths to the network:

Yellow-green wire - grounding;

Brown wire - "Phase";

Blue wire - "zero";

The power supply of the bath should only be performed through a separate protective shutdown device (RCD), a rating of 30 mA and located outside the bathroom room.

A detachable type of bath connection to a 220 V network is allowed, depending on the configuration of the bath, the elements of the hydromassage equipment may not be equipped with electric forks for connecting. In this case, they are purchased separately and installed on their own. Each unit of equipment intended to connect to the network must have an individual connection to the electrical network.

Connect units together, in one fork, etc.

Use a bath with a socket or fork without a good grounding contact.

Ground a bath through heating, plumbing and sewage equipment.

Operation of the bath with a damaged electric pump or faulty or nonconnected grounding.

Conduct technical work when the bath is included in the network.

Hydromassage and Additional Equipment

The lane can be located the following elements of hydromassage equipment (see View BUT):

El. Engine hydraulic pump

Compressor Aeromassage

buttons and Bath Control Controllers

injectors (Jeta) hydromassage (reverse side)

pipeline system

Additionally, the bath can be installed

aerome massage (installed in the bottom of the bath, see Fig. 1)

Cut mixer (see Figure 2)

Spin massage (see Figure 3)

Massage "Shiatsu" (back massage or back massage + foot massage) (see Figure 4)

Chromotherapy (see Figure 5)

Illumination (see Figure 6)

Headrests (see Figure 8)

Bathroom management

Bath function management is carried out using the following equipment:

BUT) Nozzles (Jeta) hydromassage.

Provide adjustment of the direction and forces of hydromassage jets. The direction of the jet can be easily changed by turning the nozzle nozzles within a 30-degree corner. Water jet feed force is regulated by turning the nozzle nozzle around its axis. The maximum stream of jet is achieved by the full opening of the jet nozzle counterclockwise (open nozzle).

B)Button ON \\ OFF. Hydromassage functions with air supply regulator (RPV). Provides incl. \\ OFF. hydromassage system by pressing the center. RPV is dosing the amount of air mixed with the water jet when the hydromassage system is operating due to the injection process. By turning the regulator, you can change the amount of air entering with the jet of water from hydromassage nozzles. The power of the jet increases with the supply of air into it.

IN)Button ON \\ OFF. Functions of aeromassage (highlighting chromotherapy). Provides incl. \\ Off auger system. When turning on the compressor pumps air under pressure through air nozzles installed on the bottom of the bath. In this case, small bubbles of air are pulled out to the surface, massage and enrich the skin with oxygen. Can be used for incl. \\ Off Illuminated chromotherapy.

D)Crane balance (turbo).

It moves the modes of operation of the hydromassage system between the function of the total hydromassage and the function of the back massage ("Shiatsu" massage). Adjust the desired distribution of water supply to the specified functions of the "checkbox" of the transponder.

E)Electronic Bath Function Control (No. 2).

Buttons for adjusting the power of the aeromassage function

Button ON \\ OFF. Aeromassage functions

Button ON \\ OFF. Functions of chromotherapy (backlight)

Button ON \\ OFF. Hydromassage functions

E)Electronic (sensory) Bath Functional Control Panel (№3).

Power button / power off button

Enable button / off the hydromassage function

Enable button / off the backlight function \\ chromotherapy

Multifunctional switching mode button: Radio frequency ( MHz.) / radio channel number ( ch) / Radio frequency setup mode (flashing inscription TUNE) / Volume level adjustment mode ( d.) / mode adjustment of the air arger power level (number from 1-10 ). Also used as a confirmation button when recording in memory of radio stations. In memory, you can record up to 10 customized channels ( Ch).

Modes Setup Buttons: Volume / Radio Station / Radio Dial Number / Air Aromason Power Channel Number. The setting is performed depending on the mode of the selected button 5 ( SET.).

Turn button on / off the radio.

Turn button / off button of the Aeromassage function.

ATTENTION!If your bath is equipped with a control panel, then with the water level below, all functions except radio and aeromassage are disconnected.

How to use hydromassage baths

ATTENTION! Never turn on the hydromassage bath until the water reaches the level by 5-6 cm. Above the openings of the main hydromassage jets. Avoid high thermal exposure (above 65 degrees Celsius) to the surface of the product - this can lead to its spoile! It is forbidden to include the function of hydromassage with closed jet nozzles. Before turning on the hydromassage system, make sure that the jets nozzles are not directed upwards, and the crane balance is not in the back massage position (Shiatsu massage). During the operation of the hydromassage, it is forbidden to overlap the lattice of the water intake valve, preventing water to enter it. After using the bath and drain the water, it is recommended to blow up the aeromassage jets by switching on the function of the aeromassage per 1 minute.

Never use the bathroom after the adoption of alcoholic beverages or drugs. Hydromassage for medicinal purposes can be carried out only on the advice of a doctor who will select the proper duration of sessions and the water temperature for you.

Taking a cold bath, you strengthen your health, warm or slightly hot bath you remove tension. To relax muscles and relieve pain, take a bath to 40 degrees Celsius. The first hydromassage session, which should be carried out only in warm water, should last no more than 10 minutes

The effect of the water-based massage is directly proportional to the temperature of the water and the duration of the session. After too long bathing, a feeling of fatigue may appear. And, if taking a bath, you will feel drowsiness - disconnect the hydromassage and cool the water.

People with overweight are contraindicated by hydromassage baths at a water temperature exceeding 38 degrees Celsius.

Bathroom care

For a daily wash bath, use a liquid cleaning agent, harmless to acrylic and plastic surfaces (see the instruction of the cleaning agent), as well as a soft tissue napkin. The manufacturer's company offers you a specialized cleaner "Tim-Profi", adapted to our products. To save the shine of the bath, it can be wiped with a cloth with a polishing agent. For bath wash, use only soft cloth napkins.

The deposition on the surface of the scale is removed with a soft napkin moistened with lemon juice or wine vinegar.

The cigarettes that appeared on the surface of scratches or burned spots are removed using the easy gripping of fine-grained emery paper (№1000 / 2000) with water. Return the gloss of the surface can be liquid polishing agent.

ATTENTION!To remove contamination from the surface of the hydromassage bath, in no case use metal brushes or tools, as well as solvents or detergents with abrasive additives. Avoid ammonia or chlorine on brass and chrome details.

Cleaning the hydraulic bath system

This type of purification when using rigid water (over 15 salt sediments on 1 cubic meter of water). In addition, it is recommended to clean the bath hydraulic twice a year in the following way:

Fill the bath with hot water (40 degrees Celsius).

Pour the liquid detergent at the rate of 2g per liter of water and start the hydromassage system for about 5 minutes.

After that, turn off the hydraulic pump and drain the water from the bath.

To fill the bath with cold water and turn on the hydromassage for 2 minutes.

Merge water and wash the bath (see "Bathroom Care").

The simplest malfunctions, reasons and ways to eliminate them

Certain fault	Possible reason	Remedy
The hydraulic pump does not turn on	No voltage in the power circuit (network 220 V)	Call a specialist (electrician)
The hydromassage button does not turn on (aeromassage, backlight, chromotherapy)	With the power button, the plastic tube connecting the button and the electropneumatic valve joined the function	Attach the plastic tube to the base button and re-enable the system
	Closed nozzles jets	Rotating counterclockwise, open nozzles
Hydraulic pump works, but the water from the jets does not do	Education in the hydromassage system "air traffic jam"	Disable the bath from the 220V network, fill with water and, weakening (not more than 1 turn!) The top nut of the tee hydraulic pump is to strip air from the system. After that, the nut is tightly spinning and re-enable the system.
Increased vibration in the hydraulic pump	Weakened engine mount to metallic bath frame	Wrap the engine mount bolts.

Even the most stylish interior of the bathroom will look ridiculous if you do not close the space under the plumbing device. You can decorate it with different methods, but the best and most reliable is considered to install the screen. With him you can not only improve the room, but also create a convenient work area hiding from prying views. Under such panels in the free space, you can place household chemicals, small buckets and other things.

What are there?

Modern manufacturers offer a wide range of products for every taste.

By varieties, protective panels are:

deaf;
with sliding doors;
with doors - harmonica;
with swing doors;
with shelves.
with fabric curtain.

In which option to stop the choice, each person decides himself. If you want to save free space, it is worth choosing an option with the doors - accordions that best fit into small spaces. For the comfortable location of household chemicals under the bathroom it is better to choose a product with shelves. But the deaf panels are characterized by aesthetic. They are very simply attached to the frame, but with their installation, access to the plumbing liner is limited, since not all models can be easily removed.

Full overview of all screens are looking for in our special article.

The most popular options among acrylic bath users are:

front panel.
solid screen of ceramic tiles;
sliding.

In our article we will dwell on the installation of the acrylic panel, because consumers most often prefer such a way to decorate space under the bath.

Detailed information pro installation of a tile screen and sliding panels Look in the relevant articles

Photo

The photo below presents various interesting options for decorating space under the bath.

How to choose the right size?

Any bath panel is selected for a specific size. It is very important to check whether it is suitable for your plumbing model. The length of the acrylic panels varies from 120 to 180 cm for standard foaders. And the height is 55-60 cm, but it can change if there are legs.

Most often, acrylic panels are included with the plumbing and have the same tone with the bathroom, which allows you to look like a organic overall structure. They are made of plastic coated with acrylic layer.

The benefits of the panels purchased complete with the fonts should be attributed to the fact that they are most closely adjacent to the baths of the bath, eliminating you from not aesthetic gaps. Experts are not recommended to acquire such screens separately, as they are not always suitable with accuracy.

If the screen is purchased separately from the bathroom, so as not to be mistaken with the choice of size, it is worth carefully to measure plumbing from all sides.

Installation of the front panel

With the choice, we decided now can be started to install.

It should be immediately noted that regular screens are sold complete with all fasteners, frames and fittings. Also attached a detailed step-by-step instruction on the installation.

For mounting the protective screen, the following tools and materials will be required:

roulette;
marker or pencil;
building level;
screwdriver;
wrench;
silicone sealant.

How to collect and secure the screen? Consider step-by-step instructions for mounting for Baths of the brand Triton:

STEP 1. Adjust the height of the bath. In order to not be a wide gap near the floor, it is necessary to bring the height of the fox and the front panel. We measure it using a roulette and using a wrench, tighten the legs.

It is very important after all manipulations to monitor the level. Do not forget to do it.

Step 2. Marking. Now you want to find plastic plugs on the frame or legs or legs to which the screen will be attached and mark the place marker on it to screw the screws, respectively, the location of the plugs.

Step 3. Fastening. We apply the screen and, using a screwdriver, secure it with self-draws to the frame. Then install special plugs on the screws.

The junction between the screen and tile is best to close the silicone sealant, so that the splashes did not come there and the mold did not multiply.

How to install on corner models?

For corner baths, the fastening is most often provided with self-assembly, but by special magnets and metal plates. Such magnets are initially attached to the feet of the foot.

STEP 1. Height adjustment.Just as in the case of a rectangular model, adjust the height of the legs pushing out from the screen parameters.

Step 2. How to mount the plates? On the reverse side of the panel in places where magnets will be dried, we glue metal plates from the kit for double-sided tape or silicone sealant. During drying, you can fix them with ordinary scotch.

Step 3. Installation. We apply the front panel and check that the magnets would grab metal plates.

This installation option is convenient because the question is: how to remove the screen, and then put it again - it does not occur. Everything is extremely simple, you need to make a slight effort, pulling the panel to yourself, it is also easy to return it to the place. The previous way does not differ such simplicity, there you will need to first unscrew the screws.

Conclusion

In conclusion, it is worth noting that the installation of the screen on the acrylic bath has a lot of advantages. With him, you transform the interior of the room and create an additional place to store household chemicals. To fit the bathroom more functional and aesthetic, it is worth a responsible approach to the screen choosing and carefully understand how it is better to attach it.

The well-known BAS company was widely popular thanks to the use of two modern bath surface reinforcement technologies. The first option is based on the reinforcement of the bass bath with a polyester resin with special glass. The second technology involves the use of an absolutely safe, environmentally friendly high-blooded two-component polyurethane foam.

Modern baths

Currently, the full range of companies represent:

Bass acrylic baths;
curtains to them;
shower cabins;
special shower fences.

30 modern models They have classic rectangular, asymmetric and symmetrical forms. All products are performed in accurately in accordance with the advanced Italian and American technologies on the original equipment.

Any bath with bass is molded with the help of special vacuum molding machines, the production of a well-known Italian company SELF. When using such equipment, infrared heating of certain zones is used. This method allows you to flex a sheet of the base in any necessary forms.

Popular Bass Models

At the moment, the acrylic bath bass is the best option in the ratio of price-durability for many citizens of our country. The most famous models are all angular baths, fade a curved shape, allowing to save space and ennoble the appearance of the room.

Let us dwell on three unique models that will satisfy any demands of the most arring users:

Lagoon bath bass - the maximum volume of water to the protective drain hole at the top is 295 liters. The depth of the side asymmetric model in the center is 44 cm, and the height of the screen itself is 55 cm. The electrical characteristics of this bath V - 220/240. The electrical wiring for powering the electronic elements is performed using the RCD. The standard feature includes:

metal carcass;
front panel;
comfortable removable legs for installing a bath and a drain device.

Additionally, this model is completed: cascade, safety handles, special nozzles for a relaxing massage of the back and legs, head restraint, backlight and pillow for switching button.

Bath Bas Alegra - This model has a smaller volume. Just 220 liters. But it perfectly fits into small bathrooms in Khrushchev. The maximum depth of the center is 45 cm, and the screen height is 56 cm. The classic equipment is the same as the previous model, and the additions to it as much as the head restraint, knobs, nozzles, cascade, pillow for the button and backlight. This bath is very practical and easy to handle, popular with young couples, who are not difficult to climb through a fairly high side. Low price is perfectly combined with high functionality. This is the brainchild bass - a new generation acrylic bath with a convenient angular place from durable materials.
Bath acrylic bass Nicole is enough. In addition to the form and volume, this model is no different from the previous one. The maximum amount is 290 liters. It is easy to install in space between the two walls or in a small niche, which are still found in former communal apartments. This is possible thanks to two direct sides on both sides of the product. The bed has a rectangular shape, slightly elongated on the one hand. If necessary, this bath can be equipped with a vertical resistant for hydromassage and a special original curtain for this model.

Please note: Power supply to all models is carried out through the RCD, so it is necessary to ground this device. Otherwise, the use of such a bath will be unsafe for a person.

Advantages of acrylic bath types

Last time Bass Basins are gaining increasing popularity, but what are the main advantages of such devices?

Users and specialists for the installation of sanitary accessories mark a number of advantages of such baths.

Unlike steel and cast-iron analogs, acrylic bass baths have low weight and very high strength, which was not available to non-metallic products for a long time.
Even boiling water unfailed - they have a pleasant temperature for humans and do not give the water gained to cool for a long time. This property is available through the use of acrylic, which has very low heat resistance. On average, in 30 minutes the water will cool only one deck in Celsius.
All such models of baths have ergonomic forms, specially created approximately to the bends of the human body.
Acrylic surface has high resistance to various mechanical damage: chips, deformations and scratches.
Acrylic is able for many years to maintain the original shine and does not yellow, as it happens with enamel counterparts. In addition, they practically do not slide, which makes them use more secure for children and old people.
The surface of such baths is covered with a special antibacterial layer that prevents the development of various diseases and fungal deposits.
Water is gaining quiet enough, which allows you to take a bath even at night, not afraid to disturb the family and neighbors.

Tip: If you want to install a bath model with a hydromassage function, then think about it, where the optimal placing additional equipment.

Conclusion

If it was decided to take advantage of the products of the BAS company - acrylic baths will be bought at the very reasonable price. And the number of different additional functions will turn out the usual hygienic bathing in this spa procedure.

High ecology and ergonomics of all models allows you to install and use device data for a comfortable bathing of babies and small children. They are easy to enter in any interior, due to the variety of forms and convenient installation method. The only thing you should not forget - mandatory grounding of such baths. Do not be lazy and risking your health, relying on good luck.

Gallery

Cleanness of the soul and calm - this is what any self-respecting person needs! For most of us, these concepts are the goal to which we, without noticing this and not guessing, seek themselves. As folk wisdom says - in a healthy body - a healthy mind! The same can be said about cleanliness: the clean body is a clean soul. So, in order to achieve the purity of the soul, first of all you need to achieve the purity of our body. And this is simple: just after work come and plunge into a hot bath. At the moment - there is nothing easier, but it is such a pleasure! In addition, each person sometimes needs the most small - to stay with himself, relax and think about the last day and future plans, and so that, at the same time, no one interfered with him. And what do you think, in what place all this can be achieved? Exactly! In bathroom! So to achieve the above, the equipment and the decoration of this index playing a significant role.

In modern conditions, the so-called acrylic baths obtained a significant variety. From this material you can get baths of any color and shape, it all depends solely on your imagination.

You can make a choice of bath for every taste that is fully appropriate to your desires. It is these requirements that Bas baths from Acrylic, which we offer you.

Bashes Bas have their advantages, namely:

material cools for a long time;
baths of this type do not lose colors and do not deteriorate, to serve will be durable;
high guaranteed service life (two to ten years);
in case of damage to the bath, it is easy to restore the grouting intended for this;
they are simple when installing, maintaining maintenance;
confirmed by the relevant certificate.

Here to achieve all the listed requirements, we advise you to use the baths and curtains for them the BAS brand (Bath Acril Systems). Acrylic and baths for massage with curtains will be pleasing any whimsical client.

Bas baths from acrylic are made in several stages:

1) The acrylic leaf is heated to a temperature of 130-160 ° C;
2) the trough of the desired form is formed;
3) this trough is cooled;
4) the resulting form is fixed in the right place;
5) The outer edge of the bath is covered with epoxy resin with fiberglass in several layers (it gives rigidity and strength).

But, if the bath shape is too complicated, then it will be much lower it, because Acrylic plasticity has certain limits. Therefore, you need to make a choice between the beauty of execution and reliability. If you use a high-quality plumbing acrylic in the manufacture of a bath, then your bath will not be subject to corrosion, chemical and other types of influences. In the Acrylic Bath Bas you can insert nozzles for the hydromassage. A variety of installations for your order can provide a variety of massage mode (from pulsating to oriental). If you have a plain bath from acrylic, after a while you can embed a hydromassage system into it, for which you should only buy this system and call the relevant specialist.

Consider the issue of servicing our baths. Unlike a cast iron or steel bath, care for acrylic is even easier. The only drawback is not suitable for soaking up the linen. Sanitary acrylic is not a porous material, so it is not exposed to pollution. For care, it is enough to wipe the bath with a soft sponge with a cleaning agent (you can use liquid soap and other detergents). But abrasive substances and solvents use strictly prohibited. Hydromassage baths are required annually (but not more often) to disinfect and clean from the deployed water stone. This is done with the help of a disinfectant or vinegar (1.5 liters) added to the water-filled bath. Then we make an inclusion for 10 minutes, we drain, fill the bath, and turn on for 1-2 minutes again. After that, we rinse the bath from the shower.

No matter how durable material is, but, unfortunately, he can crack and scatter. But scratches and cracks are easily eliminated. To do this, it is necessary to pass the place of damage to sandpaper. The procedure should be carried out, constantly watering water. When buying baths, you can purchase special tools adapted to remove cracks, as well as all sorts of polishing. With proper care, your bath life will reach up to 20 years.

For any bathroom fit the baths of the most common - rectangular shape. The choice of sizes is quite high, from very small to huge. To save the place of your bathroom, you can use angular baths that can be installed in small rooms. An example is the Algra Assymmetric Bath. In addition, there are also baths that have common standard sizes, such as the Imperial or Iris. But, if the size of your room allows you to install larger baths, you can install the lagoon bath. The proposed choice of forms and sizes will allow you to enjoy the bathing procedure in full!

The replacement of the bath for hydromassage or its addition can serve as a shower cabin. It is with the help of it you can save space. The shower cabin is well suited to those people who do not particularly prefer the bath. In addition to its main function, the shower cabin has a number of additional features, such as telephone, radio, etc. In addition, a Turkish bath can be installed in a shower cabin and / or a hydromassage installation.