Practical storage systems for a garage or workshop.
The garage for many is not only the storage location of the car, but also a real automotive, plumbing and joinery workshop. Therefore, it is important that it is always and everything is at hand and in the right place. But sometimes it is so difficult to understand the variety of screwdrivers, pliers, scissors, rolled and other utensils, which is stored in Men's Eden. This review is simple and effective ideas that will help create practically ideal storage systems in the garage.

1. Magnetic tape

Magnetic tape for storing small metal parts.

The magnetic tape pasted on the wall in the garage can be used for storing drills, scissors, bolts, buckets and other small metal parts. Such a magnetic holder is very convenient to use and will help prevent the loss of small, but important spare parts.

2. Plastic containers

Rack of plastic containers.

From large plastic containers and wood bars, you can build a large rack for storing tools, wires, spare parts and any other things. The organization of such a rack will restore order and significantly save space in the workshop or garage.

3. Realities

Railings for garbage bags and paper towels.

On one of the free walls of the garage, you can place several small rails, where it is convenient to place the rollers of garbage bags, paper towels, sandpaper, scotch, rope and much more.

4. Furniture brackets

Furniture storage brackets.

Many dackets use a garage for storing folding outdoor furniture. So that she did not stand in the corners and did not occupy a lot of space, make a vertical rack with wooden or metal brackets and screw it to one of the free walls.

5. Jars

Storage of nails, bolts, screws and other trifles.

Bottles, wrenches, nails, self-tapping screws, screws and other little things do not occupy a lot of space, but it is extremely inconvenient to store them in a mixed form. Banks with covers screwed to the bottom of the mounted locker or under the desktop of the desktop will help to clean up these things.

6. Grid under the ceiling

Grid for storing pipes and plinths.

The plastic grille screwed into the corner of the garage under the ceiling is ideal for storing the residues of water pipes, plinths, profiles and other long things. Such a storage system will help significantly save a place in the garage and prevent possible breakdowns of fragile building materials.

7. Organizer for screwdrivers

Wooden organizer for screwdrivers.

A small practical organizer for screwdrivers, which can be done to any man to do with any man, simply drummed the right number of small holes in the wood bar. Such a product can be hung on one of the walls of the garage or workshop to store all screwdrivers in one place.

8. Vertical storage systems

Vertical storage panels.

Several perforated metal or plywood panels under the table or in the cabinet will allow you to get an ergonomic and convenient place for vertical storage of a small hand tool.

9. Plastic pipes

PVC pipe storage systems.

PVC pipe remains of different diameters can be used to create a variety of storage systems. For example, pieces of wide pipes screwed to the bottom of the locker are suitable for storing a screwdriver, drill and other tools of this type. From pieces of PVC pipes of medium diameter, you can make cells for storing various sprays, mounting foam, tubes with paint and other tanks.

10. Tassels

Suspended storage of brushes.

Painting brushes and spatulas are very convenient to store in a suspended state on a thin wire or on a thin rod of steel.

11. Rack for Garden Tool

Wooden rack for garden tool.

So that the garden tool does not occupy a good third of the garage space, keep it on a special rack screwed to one of the walls. Such a rack can be made it with your own hands from the tree bars, a wooden pallet or pieces of plastic pipes.

12. Multifunctional rack

Rack made of pallet with shelves.

Wooden pallet, complemented by shelves from pieces of wooden rail, will become the functional component of the garage and will help to place a huge amount of hand tools and small in one place.

13. Holder for fishing

Storage fishing rods.

An ordinary wire grille can be used to create a convenient holder for fishing rods. This storage system can be fixed under the ceiling so that it does not occupy the place at the bottom and did not get confused under his feet in the autumn-winter season.

14. Pegboard

Good day, brainchina! The workshop when the mess reigns in it, this is not a workshop at all. And the topic of "ordering" tool is devoted to this article in which I collected 9 not quite ordinary ways to store a healthy tool for your mozgosaster. We guarantee that they are suitable for any tool ever existing on the planet Earth!

In the fall of 2015, I created a storage board The Ultimate Magnetic Pegboard, but time passed and I had even more tools, and meant it that I needed another self-timer For ordered storage of this tool itself. In this mozgorovodiculture I will tell you about some devices that I equipped a new board with a tool.

So let's go!

Step 1: Kitchen dispenser Towels than not holder of clamps?

My granny gave me a dispenser for paper towels, and I decided to put it in business. The rod of this dispenser was plastic and did not hold the weight of the clamps, so I replaced it with a metal guide from the old mozgoprinerwhich cut to the length of the length * and with the help of epoxy resin, glued to it on the fastening sides.

When installing this obtained crossbar for the clips on the board, I used small wooden gaskets to get more space and simplify the removal / gearing of these clamps. It should be noted that the clamps are quite heavy, so the more screws when attaching the crossbar you use, it will be more reliable.

Honestly, I will say that this method of storing the clamps is much easier than all other options for clamping crossbars.

* Guide I cut almost half lonoving than I needed that there was the place for others MoskjectsI plan to acquire in the near future.

At my crossbar of the kitchen dispenser, towels fit:

• 3 15 cm-climb clamps
• 10 cm-i clamp
• 5cm-I clamp.

And there is a place for many others that should appear soon!

Step 2: And the screed clamps than not holders?

Clamps have a wide range of applications, so why not use them as holders? In the storage board, I drove a pair of holes, I trained through them (the size of which depends on the value of the tool, which is planned to be placed in it). Tolerated from the back side of the board and inserted the tool. All simple!

Thus mortgage You can store a soldering iron, borders and a lot more! In case you are planning to place a heavier tool (for example, drill), it will be more expedient to use a metal clamp.

With the help of "Homuts", I have:

• large metal tweezers (because not "lipnet" to magnet)
• little plastic tweezers.

Step 3: What about the radiator?

This idea visited me in November 2015, and I implemented it to accommodate my plastic tweezers, securing this holder directly on the wall above the magnetic board. I attached a radiator with a bilateral tape so that his ribs are vertically, and hanging tweezers on them, and some ribs performed as delimiters!

I got this radiator from my game console, which even has a whole mozgorovodiculture.
On my "radiator" holder are placed:

• 5 different plastic ESD-tweezers.

Step 4: Magnets in the case!

I guess you have already seen my board Ultimate Magnetic Pegboard, if not, I advise you to familiarize yourself!

And in in my new tool storage board, I also used magnets, "mined" their speakers, which glued to it hot glue. This kind of holders make it quite easy, you just need to understand in what place Mozmanki. Each tool will be placed.

With my "magnetic" holders are stored:

• large sprinkling planer
• small sprinkling planer
• big iggogubsy
• kusachachi
• flat iggogubsy
• curved iggogubsy
• ordinary iggogubsy
• joiner's displacement.

Step 5: Do not forget about screwing straight hooks

From the screwing hooks, it is preferable to rendered at right angles, they better hold a massive tool, for example, presented in the photo, a large rasp with a massive handle, but even its dimensions do not help with round hooks to hold the rasp.

But with the help of straight hooks your tool to store is very simple, try this braid And find out what is the speech!

This is not visible in the photo, but I screwed the hooks also from below, as "locks", preventing the falling out of the saw, it does not matter from what.

On my "hook" holders are stored:

• brushes (no, I do not draw, they serve me for another)
• big Raspil
• large file.
• hacksaw
• and my microscope self-timer .

Step 6: And the foam is useful

You can not believe, but for storage drills I used foam. It is very soft, it weighs little and easily cuts, as a result, it is great for storing small tools, for example: drills, leggings, small screwdrivers, pencils, etc.!

About how I built a foam holder drills I created a separate Mozgorovodiculture.

Such a storage device can be made of wood, while the foam will serve as a good material for the prototype such crafts.

Step 7: And of course small shelves!

The device called the "French Planck" of course "cool", but to my regret, I do not have the opportunity to make a similar one.

Therefore, I decided to attach a bunch of 90 degrees to the storage board by means of small corners.

On my "mini-shelf" posted:

• my homemade magnetic silicone lining on the hoody sponges (because they decided to use them anymore anymore)
• two different grinding bars
• lamps for nails (although for these purposes it is possible to better use scissors for metal)
• multitole size with a credit card
• flashlight in the form of a phone.

Step 8: And even the bushing from the toilet paper there is an application!

Must admit, the idea is really strange ...

In the sleeve from the roll of paper, I cut the hole, then cut it in half and attached to the board.
I use this fixture now only for storing my xy selfieckers , it weighs little and "paper" holder is only slightly bent. Obviously, for a heavier tool, this method will not fit ...

Step 9: Another "mini-shelf", but with holes

To create it motor holder I was inspired by one recently.

There are many professions in which various types of tools are applied. Most often for their storage boxes are purchased for tools, but sometimes the high-quality storage is easier to make it yourself

If you are interested in one or another kind of crafts, and you do not sit at home, folded up, naturally, you are going to have a sufficiently large number of tools. To your tools are always at hand and securely persisted, they need to provide a system of safety in the form of a separate closed space called the box For storing tools.In addition to preservation, the use of such a box will help very help, since the filling will be carefully sorted by compartments and in the future you can find the necessary fixture "blindly". Also, this device needs car owners, or rather the owners of trucks and gazelles. In the car, the box must be well fixed. And this means that when it is manufactured with your own hands, you need to think well where it will be in the car and how to fix it there.

Decide with two criteria:

• will you just keep in it tools, or do you need it for convenience of transportation?
• what sizes of tools do you intend to store it?

Classification of boxes

By case material:

• plastic - light by weight, comfortable in everyday life and for transportation;
• metallic - much harder plastic, but at the same time much stronger, more stable, have a tougher design, there can be no large size due to the severity of the metal;
• galvanized metal plastic - light, durable and spacious, suitable for both storage and transportation of professional tools. But all these advantages determine the corresponding price - it can be from $ 150 to $ 500 and higher.
• wooden - the most affordable material for making a drawer for tools. Especially since with their own hands it is easier to do from this material, or rather from plywood 10 16 or 18 mm.

By type of stored tools:

• hand tools are usually represented by one large compartment for large tools (screwdrivers, hammers, keys) and 2-3 small for smaller tools;

• the electric tool is a case that is functionally intended for the preservation and movement of a specific power tool. Most often has one main compartment itself for the device and several recesses for snap.
• organizers - boxes designed to accommodate a large number of different tool size. Have a lot of compartments, a model with modular partitions deserve attention, which for the convenience of the owner can be rearranged from one place to another.
• professional tool is a special kind of cases with certain seats for specific tools, more resistant to drops and adverse environmental conditions.
• unprofessional tool - represents drawers of both small and sufficiently large sizes with a variety of compartments, and niches for various kinds of tools, often this case in the form of bags.

There are many firms for the production of tools for tools, such as stanley, Fit-american firms keter. - no less popular Israeli firm, Spanish firm tayG, german Kroft.and many other, characterized in quality and cost of products.

As an alternative to all these firms - the ability to make a drawer for tools with your own hands. You can thus save at cost and get a completely competitive option that meets your requirements.

Types of boxes

Boxes for tools manufactured in homemade workshops are mostly made of wood, and they have a variety of forms. Popular and easy to manufacture classic boxes - "Lukoshko". In the second and third place, the box in the shape of a chest is a container, and in the form of a case.

Materials for making tools box

• wooden boards thick 15-25 mm
• round wooden rod of the desired length
• self-tapping screws, adhesive for wood, sandpaper stripping surfaces
• tool kit - grinding machine, electric road, electrolovik, screwdriver
• measuring Tools - Rule
• screwdriver, hammer

Stages of manufacture

Using such technology, you can make drawers of more complex structures, creating the required number of compartments and niches by rebuilding.

For the same technology, it is possible to manufacture a closed box, which is more reliable and convenient for transporting tools.

Additional steps in the manufacture of a drawer with a lid

For self-making popular now transformer boxes We'll have to break the head more, but it is quite realistic to carry out this idea.

To do this, with the help of computer programs, it is necessary to develop the desired design, to embody it in the reality you will help you a set of necessary elements that can be purchased in special stores. The number and complexity of the elements selected depends on your requirements for the box. The assembly can be made on a wooden base using aluminum strips and corners. Fasteners are made using rivets.

If you are a purposeful and creative person, then the process making Toolboxit will not be much difficulty, but seeing the fruits of this work, you will increase your self-esteem and save budget funds.

Reading time ≈ 5 minutes

This owner always takes care of the preservation of its tools. Even a small set should be stored ordered, neatly. A skilled master can assemble the capacity of the tools and fixtures on their own. Below will be talking about how to make a tool box with your own hands. Presented photos and video will help in work.

Externally, the box looks good and stylish, he immediately declares a serious approach to the life of his owner. Its dimensions (70x40x45 cm), that is, 70 cm in width, 40 cm deep, 45 cm in height. This is quite enough to accommodate the hand tool. In the drawer 3 retractable tray, as well as the top folding cover, which opens the bulk compartment. Such boxing allows you to protect the tools from dust, organize safe storage.

Required tools

For the manufacture of a wooden box, the following tools will be needed:

• a circular saw;
• milling machine;
• grinding;
• clamp;
• a hammer;
• nippers;
• file;
• wood hacksaw;
• chisel.

Step-by-step instructions for making tools

Optimal material for the manufacture of frame - oak wood. It is a wonderful durable material that is distinguished by strength and resistance to mechanical effects. It is better to take the basis - glued plates with a thickness of 19 mm. This material has no bitch and rotten inclusions. Using a circular, a strip of 38 mm wide is cut off.

In order for the individual elements when gluing, the individual elements are shifted relative to each other, in the first part it is slightly ripped off the carnations, the pads remove his hat, and then focus on the protruding sharp tip.

The boards are additionally missed by glue and fix.

The glue spoke on the joints of the details is removed by the chisel, only you have to wait to glue a little snack.

As a result, it should be part of 38x38 mm. Her end grind.

The edge should be cut strictly at an angle of 90 °, so cutting off the detail of the desired length, you must not forget about the coal of the cut.

This technique will help make sure the cutting angle accuracy.

The location of each detail is marked in order not to get confused when assembling.

In each part over the entire length, the groove is cut, it must go strictly in the center.

The grooves can be made either with the help of a stationary circular saw, or with a milling machine.

On the details that are intended for the manufacture of vertical corner supports of the frame, make the transverse markup.

In the rear corner items make another longitudinal groove. In the front corner reference parts it is not needed.

For the subsequent attachment in the end part of the blanks, it is necessary to find the center, noting the point of intersection of diagonals.

It is necessary to carefully check the compatibility of the blanks.

Billets are processed with a file.

In a freely assembled frame, there are marks to subsequently lengthen the grooves.

The grooves are drunk with a tree with a tree.

The chisel is removed all too much.

These billets are needed for drawers. A corner is cut off from the end part.

Each billet is drilled for fastening with bolts.

Observing accuracy, you need to resolve the prepared details.

On the details intended for attaching and separating 2 drawers, cutouts are performed at an angle of 90 °.

By installing the details for the movement of the boxes in place and fixing them, gradually begin to fasten them.

Corners of plywood blanks are cut into the photo.

The walls of the lower boxes are attached to the sheets of plywood using selflessness.

To one side side attached horizontal parts from plywood. At first they do without the use of glue.

During fixation using clamps, you need to check the diagonality to match the sizes.

Retractable drawers are made of plywood.

The grooves can be chopped up either on a stationary saw, or with a cutter.

Details of drawers are fastened with glue.

The side parts of the boxes must have grooves for movement on the planets fixed inside.

For strength, the side parts are fastened with dowels that are cut into the flush.

For reliability when gluing, small carnations are partially driven into the surface of the front wall of drawers, their caps are removed.

Attaching the front panel to drawers, look, is smoothly located individual elements.

When gluing it is necessary to observe the limit accuracy, there should be no gaps.

At the end make the top frame of the box of plywood.

To make an exact incision at an angle of 45 °, it is desirable to use a special tool.

Billets for the frame are connected and fixed when gluing with a stretch strap.

The house constantly has to repair something. It can be a drowned crane, unscrewed shelf or broken stool. Of course, for each of these actions, a special tool is needed. As a result, it leads to the fact that a large number of self-tapping screws, hammers, spanners, etc. accumulates.

Where to remove all the tools so that they were in one place and at the same time did not attract attention? Of course, the best option will be the presence of a drawer under the tools that can be purchased in the store or make a personally.

What are the boxes?

Building stores offer not only repair materials, but also special boxes in which it is convenient to store tools in a compact form. If there is no time and desire to make such a drawer with their own hands, then you can easily buy it in the finished form. However, much better will make it yourself.

The homemade box will be direct proof that a man is a master of all hands and easily copes with any task.

Before buying or manufacturing at home, it is necessary to clearly define the type of box that will be most useful. For this, its goal is determined.

Irregular use does not assume the presence of a trimmed design. Where it is better in this case a simple box, having one section. There is another type of - organizer box. It fits more men who are constantly engaged in repair work, be it at home or in the workplace.

To make the right choice, you need to proceed from personal preferences. The selection of the box depends on the man itself and his skills and desire to make something.

How to make a drawer statenly with your own hands?

If it was decided to make a box independently, then you need to have a step-by-step instruction that includes a sequence of actions. It will help unmistakably understand how to make a box for tools without special financial and labor costs. We define the main stages of the work:

Plan definition

This stage is very important because the calculations obtained and the schemes made will allow the design of the design. If an error or error is made somewhere, then the final product can be very different from the intended.

To portray drawing a drawer, use paper and a pencil or a special program on a computer.

Materials for work

It should be clearly understood which materials will be used to create a future toolbox. They are made on mandatory and optional.

The latter depend on the specific case, and the mandatory group includes devices for measurements, fastening elements, hammer, knife, etc.

Manufacturing process

The main works that will determine the result occur at this stage.

Work on the manufacture

To understand the specifics of how to make a design yourself, we give a simple example, which is depicted in the photo of the toolbox. The design is a box-box that has a special handle to move.

What makes such a box? Plywood, plastic or metal materials are best suited. Their choice again depends on the personal preferences of the wizard. As a rule, the majority uses coniferous trees for manufacture. It's all about their availability, high quality and ease when processing.

Step by step Consider the process of making box-box:

• After the paper or computer is drawn, it is transferred to the material that serves as the basis for the design. That is, on a tree, plastic or metal with a pencil, parts are drawn, and then cut with hacksaw.
• Basic elements of the box: walls (4 pcs.), Bottom. The simplest box for tools may not contain the lids.
• Once all parts are cut, they are connected by glue and waiting for drying.
• A few hours later, when the glue finally dries, the connection site is additionally fastened with nails or screws.
• Installing a handle. As it will fit a tree from a tree.

By completing these simple actions, you can get a great tool box made by your own hands.

The finished design is additionally covered with a lacquer layer to give shine, a beautiful appearance and protect the material from fluid ingress.

The presented box-box is considered the simplest, but it is very convenient. Following the step-by-step instructions, even a beginner will be able to make this drawer with their own hands.

Of course, it is later possible to make a more advanced and complex model, but for the first experience, a simple box is not suitable for the first experience.

Stock Foto Box for tools do it yourself