Replacing the toilet - not the most difficult moment during repairs, so it is possible to cope with this work and with your own hands. In this article we describe the whole process in detail, as well as post a video for clarity.

Plumbing equipment has long been an integral part of any comfortable dwelling. But as you know, "nothing is eternally under the Looner," and your toilet will sooner or later require replacement. In this case, you can contact your management organization and, prepare money, wait for the parish of Plumbing, hoping for the loyalty of folk wisdom " experience do not offer».

You can go to another way and find "Shabashnikov" on the announcement, risking to get on unfair performers seeking to get as much money as possible in the minimum time, while not too biting. But if you have the minimum experience with a drill and a wrench, you should try to replace the toilet with your own hands.

Of course, if your old toilet bowl is thirty, it is connected by a metal pipe with a tip of top location, and welding works with a new input for water in the riser are required for its replacement. vertical tube feeding water to floors) At a smaller height - after all, you will have to turn to professionals. Replacing the "Compact" toilet (in which the tank is mounted directly on the toilet) to a similar new one, quite by anyone, familiarized with this article and read the instructions attached to the new set.

First of all, of course, you need to choose and purchase a new set of toilet bowl, a tank and drain fittings. Fasteners for the toilet, like drain fittings, is usually included - it is worth checking upon purchase and purchase if necessary. In addition, you will need:

• plastic corrugation;
• a flexible eyeliner for water - its length can be estimated, looking at the old one (the eyeliner of the type "Nut-nut" with a thread by 1/2 inches is used);
• rubber gasket on the shape of the base of the toilet or silicone sealant.

If the old toilet is quite modern and was attached to the floor with standard fasteners (screws), you can try to choose a new bowl with the same distance between the mounting holes so as not to drill the floor again - this is especially true in the case when the ceramic tiles you are laid on the floor Not going to change.

Most modern "compact", except the cheapest models, have a lower eyewash water - this means that the water enters the tank through the hole in the bottom, and does not flow from above with an annoying murmion. It is better to choose exactly such.

The remaining delights, for example, the form of a specialty in the bowl ( the so-called antimptuzka) or microlift, smoothly and without a knocking down the seat, you can choose to your taste and wallet. It is only necessary to pay attention to which release from the old toilet - direct or oblique, and the new unit to purchase a similar type.

Necessary materials and tools

After the acquisition of the "compact" itself and the materials necessary for the work can be proceeding with preparatory work.

You will need the following tools:

• a set of wrench keys (you can walk a pair of divorce);
• the perforator or an electric drum mode (if the old holes for fastening the toilet to the floor cannot use) and two drills - special - for tiles and carbide - for concrete;
• water capacity - bucket or basque and rag;
• it does not prevent the disinfection of the old toilet with a chlorine or a special tool;
• the replacement of the toilet is made with their own hands in gloves, and when drilling holes - in protective glasses.

Dismantling of old toiletza

Before dismantling the old toilet, it is necessary to overlap the water supply to the tank using a crane located before the flexible eyeliner. If this crane does not hold water, you need to block the valve at the introduction of water in the apartment.

It is worth noting that in the old houses, the tip of the pipe could be made directly from the riser. In this case, when the crane is malfunction, it is necessary to overlap the entire riser in the basement, leaving the neighbors without water from above and below - without the help of workers of the housing and operational company do not do here.

After overlapping the valve before the tank, you must not forget to drain water from the tank. Then you can turn off flexibleBy disconnecting it from the plane of the blocked crane. Here is useful substituted with a container, as a low water remains in the eyeliner.

Water supply is disconnected, you can proceed to dismantling directly the bowls of the old toilet bowl. To do this, remove plastic plugs covering the mounting screws to the floor and unscrew these screws. If you have an old house, and the toilet is mounted in the floor and wakes up with a solution - you will have to break. Read more about the right link.

The main thing is not to damage the cast-iron tee, which is an integral part of the sewage riser, its replacement is a very time-consuming occupation, will cope with which it will not be possible. Further, tilting the toilet to the sewer pipe of the apartment, it is necessary to drain the water from the air-built ziphon (knee with water that prevents the penetration of smell from the sewer system to the room). After that, you can disconnect the old toilet, driving the corrugation from the tee.

The hole in the sewer tube is better to cover with a rag or a plastic bottle of suitable diameter. Dismantling is over, you can start the main thing - installing a new unit!

Install a new toilet with your own hands

It is necessary to clean the place of installation. The new toilet should be installed in place taking into account the length of the corrugations and perform markup, bypassing the base and marking the place of holes for the fastening. So that the ceramic tile floor did not burstThe holes in it must be drilled in an unstressed mode with a special drill, then replacing the carbide, switch the drill to the shock mode and continue drilling in the slab plate.

Plastic plugs (dowels) are inserted into the holes, which will then screw the screws. It is also necessary to clean the neck of the sewer pipe. Installing drain fittings in a tank and tank attachment to a new toilet bowl is quite simple, if you read the instructions attached to the kit. Usually, the drain apparatus is already mounted in the tank, and the installer remains only to fasten the tank to the bowl using special gaskets. The corrugation is inserted with one end to the sewer pipe, and the other is dressed on the release of the toilet.

Sometimes you can meet the tips that the replacement of the toilet is performed using the sealant for corrugations, although thanks to its design with outdoor and internal membranes it is not necessary.

Toiletz is better to install on the rubber gasket on the basis of the base, it will prevent dirt under it. In the absence of gasket, you can apply silicone sealant, applying it to a thick layer on the inner perimeter of markup under the base. The toilet bowl is attached to the screws screwed into plastic plugs. It is important to tighten the screws strong enough, but not overdo it, otherwise you can split a fragile faience bowl.

Do not install a "compact" tank close To the wall of the room - it will make it difficult for further service, it can lead to the leaks of the tank joint and a bowl in the event of a small displacement, and will also cause condensate in the place of touching the tank with a wall of the restroom. After the molding of the toilet is made, you can proceed to connecting water supply to the tank. The nuts of the flexible supply are equipped with gaskets from sanitary rubber or silicone, so it is not required to further wrap the threaded connections with a fum ribbon or special thread. The nozzle of the water supply system into the tank is usually made of plastic, so the eyelid nut is screwed by hand, it is possible to slightly squeeze it with a key, trying not to damage.

Many modern eyeliners are equipped with a special plastic key, clamped on the tube and facilitating twisting. Last queue is mounted to the toilet seat, it should not cause any difficulties.

Then, without putting onto the tank, perform a trial start of an aggregate with a tank filling and water descent, check the compounds on the leakage object, and the drain reinforcement of the tank - on the correct adjustment. Leaks easy to detectIf you put the old dry newspaper in advance at the floor under the floor of the compounds. Drain fittings should ensure complete tank filling, not allowing overflow.

Connect the toilet to the water supply

If necessary, its uncomplicated adjustment is performed, the principle of which can be understood even without instruction. After the connections and fittings are checked, you can install the tank cover and enjoy the work done.

Replacing the toilet - the cost of work

If, having studied our instructions, you do not want to face self-replacement problems, then you need to use the services of a professional plumbing. The price for work, depending on the city of your stay, will be from 750 to 1500 rubles.

Also, in most major stores, offer a turnkey service, i.e. Delivery, disassembly, installation and removal of old toilet bowl. Usually, it costs 2500 rubles.

As you can see, in general, to replace the toilet with your own hands is completely simple. It is possible that you will make this work better than hired employees, and at the same time save the family budget.

Plumbing in the bathroom comes out often enough. There may be many reasons for this, but the outcome is always one - the equipment is subject to replacement. Here and the main question arises: how to replace the toilet with your own hands with high-quality and without unnecessary movements?

Good preparation is the key to successful work. Get the necessary set of tools accompanying materials and detailed instructions for beginners. Following the recommendations set out in the article, and considering the likely errors, you will cope with the replacement of the toilet on yourself.

At first glance, the formulation may seem strange. Anything is clear that the toilet should be changed when he failed. But in fact, most problems associated with the malfunctions of the sewer system and toilet bowl in particular can be eliminated without replacing plumbing.

Most often the following faults arise:

• flowing from under the bowl;
• cracks on ceramics;
• unpleasant odor from sewage.

If water constantly flows from your tank, this is a serious reason to think. Such uneconomic consumption of water contradicts the current trend in environmental protection and natural resource savings. If you drip out from the tank to the floor and you are tired of substituting the basins, and all the connections of the pipes are normal, most likely, the chip or crack began.

In this case, you can only temporarily solve the problem, but the replacement of the toilet must be produced as soon as possible. But if the water from the tank runs on the wall of the bowl in the sewer - good news, most likely to change the plumber is not necessary.

The reason for such a malfunction often becomes the protruded valve. Fortunately, the entire inside of the drain tank is sold separately, it can be simply replaced.

Plumbing faience and porcelain - fragile materials unstable to harsh temperature drops. Enamel can be covered with a grid of cracks, which not only spoil the aesthetic appearance, but also threaten the destruction of the entire product.

Such a crack is a bad sign. She could appear as a result of the fall of something heavy or simply from the temperature drop

If cracked or chips appeared on the toilet, try to replace as soon as possible. You never know, at what point the ceramics will not stand and burst under human weight, water impact or simply from internal tension.

Well, if at this moment someone will be near and can quickly eliminate the consequences of the catastrophe, otherwise you can count on the upcoming repair in the toilet near the neighbors below.

In this case, everything is so clear - replacement to be! Unfortunately, this happens very often and not only with old toilets

Set of necessary tools for work

A set of plumbing tools for replacing the old toilet bowl standard. Depending on the state of the old equipment, which will have to dismantle, and sewer pipes, as well as from the selected method of fastening the new plumbing device, the set of the necessary tools can change slightly.

Prepare the following necessary items:

• perforator;
• adjustable key;
• screwdriver;
• hoven for metal or bulgarky;
• pistol for sealant;
• hammer and chisel;
• rubber spatula;
• building level;
• individual protective equipment - glasses, gloves.

The perforator will need to knock out the holes in the concrete under the dowel, which will be attached to the new toilet. An enjoyable key is carried out work on connecting water supply. To twist the screws, you will need a flat or cross screwdriver, and for the sealing of the joints - a gun for a cylinder with a sealant.

In the disassembled form, the modern toilet compact looks like this. A set of fasteners, rubber sealing rings and a tank drain mechanism can be packed separately. No need to be frightened, all this is going together as a designer

The hammer and chisel can be useful if the equipment was connected to the old Soviet sewer rim from the cast iron. So that the bowl is exhibited exactly, use the construction level.

List of essential materials

In addition to the set of tools for replacing the toilet, with their own hands, you need to purchase additional materials that will be needed when installing:

• sealant;
• corrugation to connect to the riser;
• pipe for connecting to water supply;
• FUM tape;
• crane;
• fastener set.

In any plumbing question, the moment of sealing is the main one. Any gap or a loose connection threatens leakage.

Silicone sealant in the cylinder is the best friend when replacing the toilet bowl. They fill all the gaps and gaps, process connections

To connect a plumbing device to sewage, you need to buy a special plastic corrugated pipe. It is convenient because the pipe is flexible and is suitable in most cases. It can be flexing in any position, stretch and compress.

Corrugated pipe for connecting the toilet to sewer universal. It is suitable for both horizontal release, and for the release at an angle. Bowls with vertical drain are connected in a special way - with a special elastic cuff

To compact compounds use a sealing tape or pass - in the old manner. A dowel, screws, bolts, washers, nuts, stubs for connecting all components and installation are included in the toilet replacement mounting kit. Do not be afraid if something is missing, all this can be bought separately.

Dismantling of old toiletza

To replace the old toilet to new, you need to first produce. If plumbing is not too ancient, most likely, there will be no problems with dismantling.

Another thing, if plumbing is actually very old, and the sewer pipes are cast-iron Soviet sample. Here it will have to sweat. But first things first.

If the old plumbing is not concerned about the floor, consider you lucky. Toilet placed on a wooden stand, remove easier. Wood residues will need to be removed, and pour the hole in the floor

If everything is not so bad, and the toilet is not so ancient, it will be easier to replace it:

1. Discharge plumbing. Drain the water from the tank.
2. Prepare a bucket and rags.
3. Disconnect the tank by unscrewing the bolts from the bottom.
4. Remove the corrugation or plastic eccentric, which connect the release of bowls with sewage.
5. Remove the remaining water from the bowl with a conventional sponge.
6. Look at the fastenings on the sides of the base. There should be 2 or 4. Unscrew them with a wrench.
7. Remove the silicone sealant from under the base with a knife.
8. Remove the bowl from the tile.

In the last century, they tried to make repairs "on the century", capital. And the installation of plumbing was no exception.

Often you can meet in the apartments of the toilet bowls placed on a solution laced in the screed, rewound at the base with rags and covered with several paint layers. At the same time, the connection with the pipe is zamazano with a thick layer of cement. Now it seems ridiculous, until you encounter a replacement for such a rarite person.

If you fail to unscrew, you have to beat. Be careful not to forget about the protection of the eyes and hands from Faian's fragments

If the ceramics do not feel sorry, you can dismantle it with parts. Here will be a hammer and chisel. Follow in the area of \u200b\u200bthe joints of the case with the pipe, at the same time swinging the mount.

If it does not give in, hit the bolder in the neck of the toilet, it will split. Now it can be removed. Just do not beat the hammer on the cast-iron pipe, it is also very fragile and can crack.

Gallery of images

Capital or cosmetic repair of the toilet room rarely costs without replacing the toilet, because the reason for this procedure can be not only its deplorable technical condition, but also its moral obsolescence. At the same time, how to change the toilet independently, are interested not only in order to save funds, but for the purpose of personal control of the quality of the operation by hired employees, because The toilet is a fairly fragile thing, and the wrong installation may not be detected at first glance. The skills of self-replacement toilet bowl will also be needed in the occurrence of force majeure circumstances associated with the performance of plumbing.

Preparation for self-replacement toilet

Before changing the toilet absolutely independently, it is necessary to perform a whole range of preparatory activities:

• Turn off the water supply to the toilet tank, break the tap on the plumbing line.
• Swing the water from the tank and, if possible, drain it with a washcloth, any towel.
• Now you can unscrew the supply tap flexible hose. Be sure to control his disassembly, because Very often forgotten about it with a cut out of a sharp displacement of the toilet, which can lead to unforeseen negative results: the cliff of communications, the injury of a plumbing device.
• We thoroughly rinse the toilet and sewage itself, and then select the remnants of water in the waterproof toilet bowl in any way. If not to do this, then with his removal, all the "surprises" will be on the floor.
• We free the space for free movement and moving the toilet, i.e. Plan and calculate your way, because the device has not a small mass and dimensions.

After checking the lack of water in the waterproof and the toilet tank, as well as the preparation of the tool, you can disassemble the toilet.

Required tool

To change the toilet, you will need a whole set of tools:

• A set of standard horn keys, in particular, may be needed No. 10, 12, 13, 14. Nuts and bolts of these sizes are used to build a tank and fixing the toilet bowl.
• Pipe key number 1, pliers and adjustable key for promoting water supply communications.
• In addition, it may take a hammer, chisel and "Bulgarian" with cutting circle to dismantle metal fasteners and breaking ceramics.
• Upically, you need to have a set of screwdrivers, a sanitary sealant, winding a fum-ribbon.

Dismantling to the toilet with your own hands

The toilet is cleared, the space is released, the tool is prepared - it means that you can dismantle the old instrument and the installation of the new one.

• Removing the toilet is recommended to be carried out with disassembly and removal of the tank, which will greatly facilitate the entire design, so first try to dismantle the water tank, for which the mounting nuts are simply unchecked and it is carefully removed. It is worth noting that compact-toileties have a fastening on the bottom inside the tank, and old models with a tank mount to the wall usually have external locks.
• Very often, from the corrosion exposure to water, the threads on the attachments do not want to unscrew, so you have to use a different tool up to simple fasteners.
• The toilet itself is usually attached by two bolts-self-assembly on the sole under protective plastic caps, which are easily removed by the subsection of a screwdriver. Most often, these fasteners are very problematic from moisture, while it is necessary to work carefully, because The metal tool can easily break the base of the toilet, which can provoke its full destruction.
• Very old ways of mounting the toilet with concreting platform and sewage communication are sometimes forced to dismantle the device to completely destroy it, which is very unsafe. You can try to disclose the base of the toilet to break the screed around the perimeter of the "foot", and a ceramic neck is fought under the problematic analysis of the old sewer compound.
• The main task when dismantling is the removal of the device in any way with the mandatory preservation of the integrity of the sewer communications.

Important: In any case, the operation of dismantling the old toilet is often turning into a "punitive operation" of an unwanted plumbing device. At the same time, special attention is paid to integrity (even cracks) of the sewage rush should be, otherwise it will have to be replaced with a possible replacement of the entire riser. In addition, it is unacceptable to enter the ceramic toilet remnants or other large-sized garbage in the sewer. Therefore, shocks are not allowed with a hammer on cast-iron, steel or plastic communication, and the cleaning of the walls of the nozzle is carried out carefully with the overlap of the stroke of the large-sized polyethylene plug.

Considering the question of how to change the toilet promptly, but still independently, it is necessary to remember that the process itself may take several days, because it is a replacement of the toilet in the already renovated room (i.e., only the replacement of a similar device), and another thing - This is the re-equipment of the toilet with the installation of another modification of the toilet. Therefore, the installation of a new device can have two junctions:

1. Easy replacement of plumbing on a similar when dimensions and designs for connecting communications coincide. To commission the toilet bowl, it is enough to hold it to the floor with a specialized kit of mounting bolts, install a tank with a reliable fastening (do not forget to properly put the rubber sealer), collect and configure the accessories of automatic tank filling with water, connect tap and sewer communication.
2. Installing a new device with modernization requires preparatory work:

• Accurate determination of the installation site of the toilet base in accordance with its size and laid communications.
• Check the quality of the condition of the flooring and its level relative to the sewer cut, i.e. A new ceramic tile must be flattened, while the sewer nozzle of the new toilet should be higher or accurately at the level (but not lower) the riser of the sewage riser.

It is necessary to check and coordinate the selection of adapters to connect communications, for which tap flexible hoses and sewer adapters with rubber seals are selected. It is necessary to pay attention to the length of the communications connectors that should not be small. Corrugation is often used to simplify the sewage connection.

The end of the process is to fasten the toilet to the floor and its full assembly with connecting all communications. Primary start of water Organize smooth, partial discovery of the crane, because There may be leaked, which will require immediate overlap of water.

Tip:to improve the sealing of communications in the fields of prefabricated nodes, use silicone sealant, just do not forget that it takes a curing time, so you have to wait a couple of hours before operating tests.

Replacing the toilet may be required when changing the design of the toilet room or at a banal breakdown of a plumbing device. The work of professional plumbers is quite expensive. In addition, it is difficult to harmonize the time of the operation. To avoid such problems, you can change the toilet on your own. How to do it, read further.

Dismantling of old toiletza

Toilet may be:

• outdoor, that is, installed on the floor of the toilet room;
• suspended, that is, attached to one of the walls of the toilet room.

The choice of dismounting method depends on the type of toilet set.

Removing outdoor toilet bowl

Before entering the installation of a new plumbing product, it is required to disassemble the toilet bowl installed earlier. The work is made according to the following scheme:

1. water overlaps entering the drain tank. To do this, it is enough to close the valve on the plumbing pipe;
2. disconnects the water liner from the toilet tank. To perform the work, you will need the key of the desired size or recording plumbing key;

1. all water merges from the tank. The residues of the liquid to avoid the strait are wet up with a soft cloth;
2. the toilet tank is removed. To do this, unscrew the locking bolts located in the bottom of the drain container;

1. at the next step, it is necessary to determine the method of connecting the release of the toilet and the sewer pipe. Currently, the compound is equipped with a rubber cuff compacted by a sealant. Previously, the junction was sealed with cement mortar:
   • if the joke is equipped with a cuff, then to dismantle it is necessary to gently cut the sealant layer and remove the seal from the sewer hole;

• if the jack is smeared by a cement screed, then a hammer and chisel will be needed to shut down the toilet bowl. Cement screed using tools is irritated on small pieces and gradually removed.

Perform the cement removal work is required extremely gently so as not to damage the sewer inlet. Otherwise, when installing a new plumbing, a pipe replacement will be required.

1. after disconnecting the toilet bowl from the sewage, you can proceed to the direct dismantling of the plumbing product. The toilet can be attached to the floor:
   • with fixing bolts. In this situation, a screwdriver and a wrench and wrench are sufficient to remove the toilet bowl. Decorative caps are removed from the bolts, after which they are easy enough to unscrew;

• with the help of epoxy resin. In this case, dismantle the plumbing without damage will not work. To remove the toilet, it takes a slightly splitting the product in different directions to partial destruction of the deterrent glue seam. When performing work, you can slightly help with third-party tools, such as a knife;

• using taffeta (wooden laying). Remove the toilet with taffes is simple enough. You must unscrew the locking bolts. However, after dismantling plumbing, it is necessary to remove the wooden gasket and the vacant space to pour the cement-concrete mixture.

It is possible to start installing new plumbing after a complete hardening of the solution, which takes up to 7 days.

1. the installation site of the toilet bowl and compounds of plumbing with the sewer tube is cleaned of garbage and other contaminants.

Removing the mounted toiletaz

You can replace the toilet toilet type with your own hands as soon as possible. To dismantle the old plumbing product, you need:

1. little to weaken the bolts fixing the toilet on the installation;
2. disable a plumbing device from drain tank and sewage;
3. fully remove the toilet with fasteners.

The work on the dismantling of the suspension toilet is more convenient to produce together, as at the same time weaken the fixing bolts and support the plumbing device at one level is impossible.

Installing a new toilet bowl

The method of installing a new toilet, as well as dismantling the old structure, depends on the type of sanitary product.

Installation of outdoor toilet bowl

How to change the flooring toilet in and install a new product on the spot dismantled plumbing? The process of work is the following steps that it is recommended to be carried out in the indicated order:

1. build toilet bowl. On the bowl, you must attach the drain tank and install it with accessories:
   • when installing, you need to be guided by the appiled scheme;

• the installation of the tank is made on the rubber sealing ring;

• the tank fixation is made by special screws included in the sanitary product. Each screw must be equipped with an individual rubber gasket for compound sealing;

1. to the outlet of the toilet bowl, the rubber cuff is mounted for connecting plumbing with sewage intake. When installing the cuffs, it is recommended to use a silicone sealant, which allows to obtain a more durable and durable connection;

1. the assembled plumber is placed on the selected place. The ability to correctly connect the device to the sewage network is checked. Marking on the floor for fastening bolts;

In order not to install the toilet further on the wrong place, it is recommended not only to determine the area of \u200b\u200bthe location of the fasteners, but also to circle the body of the toilet leg. Additional marking will allow you to clearly install the toilet to the selected place.

1. in the area of \u200b\u200bthe area, the holes for fasteners are drilled;
2. dowels are installed;

1. the final installation of the toilet to the place and the connection of plumbing to the sewage and water supply is performed. After installation, it is recommended to compact the connection between the floor and the foot of the toilet toilet.

Replacing the toilet to the video with step-by-step instructions for performing the work is presented below.

Installation of mounted toilet

Installation, subject to pre-installation of installation, is made in several simple steps:

1. a connection to the toilet bowl with sewage and drain tank is performed;
2. the toilet is fixed on fastening bolts.

Knowing simple rules and instructions presented in the article to replace the old toilet to the new one without difficulty.

Any technical means have their own lifetime and may fail, it concerns the plumbing, including toilet bowls. When breakdown, plumbing equipment have to think about its replacement. Such work includes disassembling the old toilet and the installation of the new, in the article we will analyze these processes.

Preparatory work - what to do before replacing plumbing

The reason for the replacement of sanitary equipment in the apartment can be not only a breakdown of old technology, but also its unattractive appearance. The old toilet may not match the visual characteristics of the interior of the bathroom, spoil the image of the entire dwelling, to reduce the means and strength invested in the repair room. Even if it regularly performs its functions, but it looks unprepacently, it is better to replace it, even though it will cause additional financial costs.

Before buying a new device, it is necessary to determine the scale of the repair work. Full replacement toilet is not always needed. For example, if the breakdown of the old technical means lies in the cracked tank, you can simply replace the tank itself, but do not touch the toilet.

If you want to replace the entire toilet, you should first select a new plumber, which should be the most functional, attractive and appropriate external lane parameters. Toilet bowls differ among themselves not only by visual characteristics, but also by the form and direction of the necklace, through which the device is connected to the sewage network. On the market you can find equipment with the following types of release:

• oblique;
• straight under 90 degrees;
• vertical.

All types of issues have their own positive and negative qualities, but direct and oblique releases are considered the most functional and convenient, because most modern toilet bowls have such compounds. Before buying, you need to measure the bathroom. This information will allow you to select a plumbing device that perfectly fit into the room not only in your visual characteristics, but also in size.

It should be remembered that it is necessary to place the toilet in the room with some parameters. First, the device should be located at a distance of at least 60 cm from the door. Secondly, there should be a free distance between the toilet and side walls - at least 20 cm. Compliance with these standards will allow in the future to use the bathroom as much as possible. When buying it is recommended to pay attention to the design of the old and new toilet. It is not always a hole connected to the drain channel, is located in the same place, because after installation, the new device can be accommodated at all as the old one was installed.

Tools and materials - what you need to repair the bathroom

Replacing the old toilet to a new one is a fairly simple job that the owner of the apartment can perform with their own hands. To do this, you need to pre-purchase or take some tools from familiar, without which dismantling and installing cannot be performed. To replace the plumbing you will need:

• shock drill or perforator with special winged drills for working on concrete;
• a set of wrenches for assembling locking reinforcement and connecting water hoses to the device;
• pipe and Swedish adjustable keys;
• screwdriver Set;
• a hammer;
• cement glue;
• callery with sealant.

In addition to work tools, some materials will also be required. In particular, it is necessary to purchase suitable water pipes through which the drain tank will be connected to the water supply system. Previously, metal pipes were mostly used to connect plumbing, but today it is most popular with products from metal plast and polypropylene. Such pipes are not so durable as their metal analogs, but it is much easier to work with them - no special skills and tools will be required for this.

When installing, the pipe and Swedish adjustable keys will be required.

To work with metal products, you have to use welding, trim consumables manually, cut into threads and perform other complex works, due to which the replacement of plumbing was a very difficult task, unbearable for many owners. It is very differently the installation of metal-plastic pipes is performed, they are collected using special accessories, which makes it possible to perform work by people who do not have any experience.

Dismantling - Remove the old toilet independently

The dismantling of the old toilet is the first stage of work, which is recognized by many experienced specialists the most difficult and responsible from the entire replacement procedure. It is when dismantling that various difficulties and trouble may occur, for example, the fasteners could rusted and now interfere with remove the drain tank. From constant contact with water, metal products become substandard and unscrew them can be very not just.

Difficulties may also occur when removing bowls of toilet bowl, where attachments can also be corrosion. And even earlier, the release of sewage from cast iron pipes was fixed on the toilet and shuffled with concrete solution. As a result, after many years, disassemble the connection without damaging the old toilet and the fasteners is almost impossible.

If you do not want to keep the integrity of the installed toilet, the bowl can be simply split into several pieces with a hammer or a sledgehammer. If necessary, keep the old device in a normal state from self-dismantling it is better to refuse. It is impossible to extract the toilet base from the cement base on its own.

The entire dismantling process will include the following steps:

1. 1. Disconnect the tank from water supply. Just disconnect the pipe through which water flows into the tank, with a wrench and drain the water remaining in it.
2. 2. Disconnect the toilet tank. To do this, unscrew the nuts located on the back of the design, and slowly raise the tank.
3. 3. Release the base of the toilet. If a tile is laid around the toilet bowl, it needs to be dismantled, then unscrew the nuts fixing the bowl on the floor, they can be from 2 to 4 pieces. If the seal of the socket is made of cement, it should be predened for a hammer and a chisel (use a thin chisel).
4. 4. Show the sewer tube with the plug. The pipe should be closed so that the sewer gases do not fall into the apartment during further work.
5. 5. Remove the old toilet. It is recommended not to regret the old plumbing agents and simply discourage the hammer to the toilet toilet (in compliance with safety) and free the sewer.
6. 6. Clean the fool from the residuals of the solution and fragments of ceramics.

In some cases, disconnect the release of the toilet and the sewage pipe is extremely difficult. Cast iron products over the years of operation can figure out rust, which makes a connection with the toilet even more reliable. In this case, it is possible to cut a cast-iron flange from the outlet to the toilet bowl and finish dismantling work.

Installation of new plumbing equipment - the best way

There are several methods of mounting and mounting the toilet to the base. After purchase, it is recommended to carefully examine the instructions for installing from the manufacturer, it indicates the preferred method of performing installation work. In any case, after the release of the site for the installation of Plumbing, it is necessary to connect the clean output of the sewer tube with the corrugated hose. Next, place the product and outline of its contour using a feltwaster on the floor and mark on the floor fixation point of the bowl to the horizontal plane.

There are several ways to fastening the base.

Further works depend on the method of installing the device for the base provided by the manufacturer of the device. One of the most popular installation methods is the attachment on a dowel. For such an attachment, it is necessary to make marks in the floor with a felt-tip pen in the floor with a drill or a perforator. Next, the bowl is installed and fixed with dowels in advanced holes. After that, you will only remain processing the seam between the bowl and the floor with a special silicone sealant.

The popularity of this method of installation is due to its simplicity. Such work can without any particular difficulties, even beginner. After installing the plumbing device, only to assemble the tank according to the instructions, install it on the bowl, fasten the bolts and connect the drain tank with the water supply system.

If the hose of the tank connections from the water supply pipe in good condition, it can not be changed, however, if there are corrosion traces, it is better to replace the product to a new product.

The second way to install the bowl on the base involves the installation on a solid gasket. This is a fairly old installation method, involving the placement of the device on a special wooden laying, which is fixed in the base niche. The gasket is placed in a pre-made niche and fixed with concrete solution. The new bowl of the toilet bowl is placed on the laying and fix on the blackboard by screws, after passing the connection with rubber washers. This is a clearly outdated way to install, which is rare, but used today.

The third fastening option involves gluing the toilet bowl to the surface. The floor and the lower plane of the toilet is processed by abrasive and degrease, after which they are lubricated with a thin layer with a special epoxy adhesive composition. After that, the bowl is pressed to the floor and left until glue decreased by 12 hours. The gluing is rarely used, however, when using high-quality adhesive composition, this method allows you to achieve reliable fastening, but with the subsequent replacement of the toilet may occur serious difficulties.

We recommend installing units only on a dowel. This method provides the highest possible connection as high as possible and allows you to replace the device for a new one in the future with minimal attached efforts.