1.
2.
3.
4.
5.
6.

Since the connection of a washbasin to sewage can be performed by the personnel, to attract specialists to this work there is no need. But in the absence of the skills of the installation of plumbing and insecurity in their abilities, you can use the services of professionals. It follows the installation of the sink at the end of the repair. The technology of mounting the kitchen sink and washbasin in the bathroom is similar.

Preparation for the Connection of the Shell

Determining the height of the installation of a plumbing device (more: "The height of the installation of the sink - at what height is correctly installed"). Sink, not equipped with additional accessories, is located at an altitude of 850 millimeters. At this level, the horizontal line is carried out - it will be a guide to mount the washbasin. The upper surface of the plumbing device must match it.

In the presence of a support leg or when the sink is installed in the bedside table, the plumbing height is not necessary. This parameter depends on the size of the leg or the couch.

Marking places of fastening on the wall. Before mounting the fastener system, you must perform the appropriate markup on the wall. The sink bowl in order to connect the sink to sewage, has mounting holes.

The sanitary device is applied to the wall, as in the photo, combine its upper edge with the conducted line and mark the places in which the holes for fasteners will be located. This work is easiest to be performed together. One person must hold the washbasin near the marked line, and the second at this time will be able to bottom to mark places for fasteners. If there is a leg or support cabinet, the mounting work is simplified - plumbing is placed on the support and on the wall place the attachment points.

Mounting fasteners for sink

Perform this work in the following sequence:

• according to the applied markup in the wall, drill holes;
• they are clogged with dowels;
• then they screw the special fastening studs.

Instructions that clarify how to connect the sink in the bathroom or in the kitchen, involves the use of dowels, nuts, fasteners and plastic liners, which are included with the plumbing device.

Screwing the hairpins, you should pay attention to the depth of their installation, since it should allow you to hang the bowl of the washbasin and fasten the fastening nut. This means that a part of the stud, protruding from the wall, should be of such a length that slightly exceeds the thickness of the sink and has an additional one and a half centimeter to twist the nut.

Connecting washbasin to water supply

Installing the mixer. By connecting the sink to the sewage in the bathroom or in the kitchen, you can install a mixer after attaching to the wall of the plumbing device, but experts recommend making this work until the washbasin is fixed. The fact is that all connections to it and the mounting process are performed below (read: "How to choose a kitchen mixer - views, features, principle of operation, the choice rules").

Installation work The mixer is made in the following sequence:

• depending on the type of mixer, one or two studs are screwed;
• install hoses supplying hot and cold water, and tighten them with a horn key. The tightening is performed with moderate force very carefully, given that after mounting the mixer on the sink, they will not be tightened the tighter;
• according to the washbasin connection scheme, you need to carry out hoses for water supply through the hole in the washing;
• on the reverse side of the studs are equipped with sealing gum, clamping washer and fastening nuts, which are tightened by a wrench.

It should be paid attention to how correctly the nose of the mixer is located - the product is installed at a right angle relative to the fastening wall or the sink side adjacent to it. READ ALSO: "What a corner washing for the kitchen is better - views, advantages and disadvantages, fastening methods."

Mounting washbasin on the wall

The sink is fixed after completing the connection to the water supply system:

• the washing with the mounted mixer is placed on the fastening studs, which are screwed into the wall;
• plastic liners insert into place;
• in completion, tighten the nuts.

As for the washbasins having a support, their connection is starting with the installation on the pedestal or bedside table.

Connecting hoses to the water supply system. Between the crane and the sealing nut put the gasket. The nut does not need to delay much, because the rubber gasket is usually well compacted. It can be tightened after the test (after turning on the water supply). If the leakage occurs at the junction site, it will be necessary to further tighten the nut. See also: "".

Connecting sink to sewage

There is a procedure that determines how to connect the sink to sewage. Perform this work starts from the installation of a siphon. Here there is a nuance: the presence of holes in it intended for overflow protection, suggests that this product should have a special pipe for overflow. Siphons in shape are bottle and S-shaped. See also: "How to choose a siphon for a sink - varieties, differences, how to choose."

For kitchenware, the S-shaped product should be used, since the bottle siphon is more susceptible to the speedy clogging and it will be necessary to clean it often.

The height of the sewage to the washbasin and the kitchen sink differ:

• for kitchen sink, this indicator is 300-400 millimeters;
• the height of the sewage for the sink in the bathroom - 500-550 millimeters.

The sink is connected to the sewage in this way:

• it is inserted into it and fix the release of the siphon;
• it is connected to it pipe (corrugated or rigid at an angle). It is very important to pre-perform a reliable fastening of the sewer pipe to the wall;
• the fastened pipe is placed in the sewer stock. If the diameter of the sewer tube for the sink exceeds this parameter in the pipe from the siphon, then the use of a special adapter (sealing rubber cuff) will be required;
• produce check all connectors to the presence of leaks.

Several important comments

Prior to the connection of the sink, you need to consider some nuances of the work:

• to connect the kitchen sink to sewerage, it is not necessary to delay all the compounds strongly, since in this case you can damage rubber sealing gaskets;
• in the case when when checking the quality of connections between the pipe and the cuff, there is a leakage, then you need to remove the cuff, dry the surface well to be rented. Then the dry cuff is lubricated with sealant and compound again;
• to connect a double kitchen sink, a special siphon should be purchased, which has a two-pipe output.

Each homework, subject to the execution of the installation rules, can connect the sink or sink for the kitchen with their own hands.

Carrying out repair work in the house requires special attention to each detail. So, an important part of the process is the connection and installation of shells in the kitchen and in the bathroom. It is possible to entrust these procedures to the pilot plumbing. But these actions are not so complex. Connecting the sink is possible to fully independently. This will not require special knowledge. Independent connection Shells will solve significantly save financial resources and work for a small time.

Preparatory work

The main development of the connection of the shell in the kitchen and in the bathroom is one. Consider the main steps of preparation for the connection process:

1. Installing a place for fastening. Determination of the height of the placement of the shell.
2. Holding work.
3. Installation of fasteners for fixing shell.

Setting the place of attachment

At the end of determining the location of the shell, it is necessary to figure out the height of its installation. It depends on its type.

The sink located in the bathroom may be installed on the pedestal or without further details. If additional details are not attached to the sink, the average height of its placement should be 85-90 cm, if the installed sink has a supporting horn or other details for the support, the height of its installation is obliged to correspond to the height of the support details.

The height of the installation of the shell, mounted in the kitchen, should be one with a kitchen bed height, which will be installed. To fix the selected height level on the wall surface, you need to make a horizontal line.

Holding work

On the surface of the sink there are holes for fastening. You need to make the sink to the wall side with the holes. Along with this, it is directed to perform the installed shell height - focus on the horizontal mark. On the wall surface, it is necessary to note the place where the holes for fastening the sink are directed. In order to work, it was performed correctly, it is recommended to perform it together. Along with this, one person will hold the sink, and the second is to mark the markup. For convenience, markup is possible to be reduced.

In the event that the installed sink can an additional support in the form of a pedestal or bedside tables, plumbing may first put on the support, and then make the placement of the mounting place.

Installation of fasteners for fixing shell

Installation is carried out in steps steps:

1. Drilling holes in places placed for fastening.
2. Installation of fixing dowels in the holes. It is recommended to use dowels from plastic.
3. Installation of the fastener. Made by screwing.

Determining the level of the length of the fastening stiletto. When choosing the length of the fastening stiletto, the thickness and thickness of the fixing nut shell are required. In most cases, it forms 1.5-2 cm.

Connection

How to connect the sink in the kitchen either in the bathroom yourself? Work is carried out in a pair of main stages:

1. Conducting installation works on the mixer.
2. Fixation of the product on the wall surface.
3. connection and installation of the water supply system.
4. Conducting the sewer system.

Installation work

To simplify and optimize the installation process, it is recommended to pre-perform the installation of the mixer, after that - connecting the sink.

The mixer is installed by performing strict rules of its location. Installation is required to be carried out strictly at right angles to the surface or to the sink side.

Working:

1. Installation of fixing studs on the mixer. In some models, mixers need to install 2 studs.
2. Connecting pipes for cold and warm water. They are sent to fix with the horn key. The degree of tightening is average.
3. Through the hole in the sink, you need to stretch and install hoses for the supply of cold and warm water.
4. Installing fixing studs. It must be strengthened with the help of sealing materials. In most cases, a special gasket is used. It is mounted on the inside of the heel. It is compacted with nuts and clamping washers for fixing fasteners.
5. Tightening nuts. It is performed using a wrench.

The installation order of the mixer is presented in the following video:

Fixation on the wall surface

At the end of how the conjunction of the sink was carried out to the water supply, it was possible to fix and fix the sink on the wall surface.

The prepared device must be put on the fixing studs mounted in the wall.

Making plastic or rubber liners.

After that, install and spin fixing nuts.

Tip! If the sink is installed, which has the support elements (for example, pedestal, either a bedside table), you need to take into account their height and only later create a shell fixation procedure.

connection and installation of the water supply system

You need to connect the pipes of cold and warm water, fixed on the sink to the system of the pipeline. The fixation is guided by a wrench. The degree of twisting is average.

In order to the connection, there was an outstanding density, it is recommended to establish an intermediate laying between the materials. It is recommended to apply the product from rubber.

Upon completion of the pipeline connection, you need to check its level of reliability. To do this, go to turn on the water and check whether the water leakage is formed. If it occurs, you need to rapid nuts in places of fastening the pipeline.

The main scheme for connecting the sink is shown in Figure:

Connection to the sewer system

In order to connect the sink to sewage, you need to connect to it siphon.

It is possible to apply devices of different forms. Experts advise apply S-shaped device on kitchen sinks. This type of siphon is least subject to clogging.

For mounting the sink in the bathroom it is possible to use a bottle-shaped device. Drain of the sinks in this siphon is more prone to pollution, based on this, it is suitable for use only in the bathroom. In the kitchen room, this type of siphon will need to be cleaned weekly.

Conducting work on the connection of the sewer system:

1. fastening and installing a siphon on a sink washing.
2. Attaching the pipe to the device. In the kitchen premises it is recommended to use a corrugated pipe, in the bathroom - a pipe from solid materials.
3. Connecting the installed pipe to the sewage system. With the difference in the diameter of the pipes, it is recommended to apply the adapter - cuff. It is made of rubber and allows you to perfectly compact the connection points.
4. check and connecting it to it for leaks.

Identification of inaccuracies in work

In the event that inaccuracies were allowed when connecting the sink, the following may indicate them:

• the appearance of unpleasant odor;
• siphon moisturizing when working sink;
• appearance of puddles and leaks under the sink;
• slowing the speed and the emergence of difficulties during water drain.

Checklery controlling the installation.

Video

Visual video instructions are presented below:

When performing serious repairs in the bathroom, as a rule, plumbing changes, including sink. This item must be properly selected and correctly installed by connecting it to the wastewater system and water supply system. Installation of the washbasin may well be carried out on its own, since the connection of the sink to sewage and the water supply is not a particularly difficult task. However, this is a fairly simple process there is some tricks and nuances that will be useful to learn the masters for the first time to perform such work.

One of the required plumbing items installed in the bathroom is a washbasin. So that it is convenient to use the sink, you should choose to choose it, correctly install and gently connect to the water supply system and the sewer system.

Installation technology and washbasin connection is quite simple, therefore there is no particular need to invite specialists to perform this operation. But those who are taken for this work for the first time will be useful to read how to connect the sink to sewage and watch the video on this topic.

Selection of shell and siphon

So that the installation can be done without problems, you need to choose the correct materials.

How to choose a sink?

The sinks are produced by the most diverse, for example, in the installation method distinguish the following varieties:

• Console. Such a washbasin is attached to the wall on the brackets, while the pipes of the water supply and sewage, as a rule, are paved secretly, in the wall.

• Embedded. These models are installed on the Tumba or the worktop. This installation option allows you to successfully hide the pipes and use the space under the sink to store a variety of items.

• "Tazik." Models may have the shape of a cube, bowls or hemispheres, they are installed on top of the countertops.
• Tulip (pedestal). The washbasin of this type has a "leg" in which all the necessary communications are placed.

As for the materials from which the sink is manufactured, in most cases, models from plumbing faience or porcelain are used. Recently, popular models made of natural or artificial stone are becoming popular.

Tip! If you wish to make an original interior, you can choose a washbasin made of glass, metal or even a tree.

Several tips for choosing shells for bathrooms:

• It is necessary that the entire plumbing, which will be installed, was performed in a single style.
• When choosing a model, the room size should be considered. For example, the equipment of a small bathroom will perfectly complement the compact corner washbasin.
• It should be noted that in the models of the shells there is a different number of holes for the mixer. Therefore, only certain varieties of mixers can be installed on them.
• On the sink, as well as on the bath, it is desirable for the presence of a overflowing hole.

How to choose a siphon for a washbasin?

Siphons are available in different versions, they differ in manufacturing materials and constructive features. So, according to the design, the following types of siphones are distinguished:

• Corrugated. These models have the simple design itself, they are a release connected to a corrugated pipe installed on the curved framework. The frame is used for the convenience of installation.

Tip! This type of siphon is attractive to its simplicity and compactness, it can be installed, even if the space under the sink is limited. By cons design, the complexity of cleaning can be attributed, in order to wash the corrugated pipe, the siphon will have to completely dismantle.

• Bottle. This is the traditional model of a siphon, which is used very wide. This embryal option can be called the direct opposite of corrugated siphons on positive qualities and minuses. So, the bottle siphon is much more complicated than corrugated, but it is possible to clean it without any problems, for this complete disassembly does not need. Another advantage of such a design is that an additional pipe can be connected to it. This quality may be needed when installing a washing machine.

• Pipe. This model of the siphon is performed as a curved pipe, in the knee of which the water shutter is located. For cleaning such a siphon, a complete dismantling is not required. It will be enough to disconnect only the bottom knee.

Tip! Water shutter on tubular siphones shallow. Therefore, they are not recommended to be installed where the sink is rarely used, for example, in the country. The fact is that if you do not use the sink, the water shutter in it will quickly dry, and the smell of sewage will penetrate into the apartment.

All listed varieties of siphons are produced, both with overflows, and without them. Siphon selection tips:

• The most important thing is to look at when choosing, this is a correspondence of the model of the sifone of the shell. If the sink is standard, any universal model of the siphon is suitable for it. In the event that the sink has a special design, then it is necessary to pick it up a special type of siphon.

Tip! As a rule, manufacturers try to complete non-standard sinks with strapping, so it will not be necessary to select the siphon separately.

• An important characteristic that affects the choice is the bandwidth of the model. Here you need to take into account the water pressure, as well as the planned connection to the siphon of additional devices, such as a washing machine.

Tip! The greater the planned volume of waste, the greater cross-section of the taps and the siphon itself should be selected. If the bandwidth of the siphon is not enough, then not to avoid the man-made "Flood".

• If the siphon is not hidden by a worktop or pedestal, then you should pay attention to its design. Here the choice is quite wide, so you can always choose a model that will be harmonized with the interior of the bathroom.

Installation of the shell

Before connecting the sink, it is required to install it. Here are some recommendations for the performance of this work:

• If the sink is put on the "leg" or embedded in the tabletop, there are no problems with determining the height of its location. The sink of the console type according to the standard is installed at an altitude of 85 cm from the floor.

Tip! The height of the sink is determined by considerations of convenience, so it can be changed, if necessary.

• The bowl of the sink has fasteners. Having attached it to the wall and aligning it on the marked line, the location of the holes that will need to be done in the wall are planned.
• For fastening the washbasin, brackets running with it included.

Connecting shell

The sink installed in place should be connected to the system of sewage and water supply.

Connect to sewage

Connection is done like this:

• A siphon release is inserted into the drain hole.
• The pipe is screwed to it - corrugated or tough with knee.
• Pipe is inserted into the release of sewage. In the event that the diameter of the sewage and release pipe does not coincide, the adapters from rubber need to be used.
• After installing the installation, it is necessary to check its quality by carrying out the release of water from the sink.

Connect to water supply

• First of all, the mixer should be installed. Most models of mixers can be installed on the already fixed sink, but in some cases it is necessary to do this work in advance, since the mixer mount is carried out below.
• Depending on the model, the mixer is installed on one or two mounting studs. On the reverse side of the shell on the studs, sealing gums and clamping washers are installed and, only then, naked nuts.

• Then the hoses are connected to it for which water will come. Tightening fixtures should be made with moderate effort so as not to drag the thread. Hoses are skipped through the hole in the sink.
• Now you can tighten the key to the well-fitting nuts.
• When installing the mixer, you need to ensure that its spout is located at a right angle to the wall adjacent to the washbasin.
• It remains to attach flexible hoses to the pipes of the water supply. In this case, the threaded connection is condensed with rubber gasket.
• The last stage of work is to check the tightness of the compounds. To do this, you need to open water and see if there is no leakage somewhere. When detecting loose connections, they need to tighten.

Installation and subsequent connection of the sink - the work is not too complicated, but quite laborious. At some stages, it is desirable, the presence of an assistant (for example, when performing marking and strengthening the shell). But, nevertheless, any home master, if desired, can cope with the installation of a washbasin without attracting professionals.

After selecting and buying a sink or washbasin, the most important steps - installation, connection to the water supply and sewage. In many ways, the landscape nuances depend on the type of sanitary appliance. Sinks can be different types - overhead, console (suspended), mortise. This determines the selection of the siphon, the specifics, convenience of connecting the washbasin and washing to sewage.

Installation of the washing in the kitchen and washbasin in the bathroom is approximately equally, because The appointment of devices is similar. Most often, the owner of the house can perform all the work independently. There are general rules that need to be adhered to when installing plumbing, they must be felt. However, if there are no instrument management skills or a complex plumbing installation is planned, it is better to call the masters.

Installation of the sink in the bathroom

General scheme for installation of shell

1. Preparatory work. At this stage, the locations of the car wash on the wall are placed, the fasteners are screwed down and are determined with the features of the mounting of the support, if it is provided.
2. Connecting to the water supply. These works can be performed when the sink is already firmly attached to the wall, but the mixer is better to install in advance.
3. Fastening a plumbing device. At this stage, it is necessary to securely fix the washing on the fastening details and supports, finish working on connecting to the water supply.
4. Connecting washing to sewage. This is the final stage of work. It is necessary to properly install plumbing equipment, achieve the tightness of the compounds. The convenience of its operation, the presence / absence of blockages in the future depends on the correct connection of the washbasin to sewage.

Sink or Shell Mounting Scheme

Stage # 1: Cooking fastenings for sink

If a simple model is selected without additional accessories, and the washing machine or other device will not be installed at the bottom, the optimal height of the sink is 850 mm. The plumbing device will be convenient to use, and the installation of the siphon and the connection of the sink to sewage can be performed with their own hands, because Spaces will be enough, and access to all elements of the system will remain free.

For a model with a support, the height is determined depending on the height of the leg or furniture in which it will be mounted. When it is decided where the sink is installed, an even horizontal line is performed on the wall. The device is applied to the line, mark the place of attachment. Alone is difficult to do it, so the assistant needs to hold the washbasin. If plumbing is installed on the leg or furnishings, the task is simplified.

On the finished markup make holes in the walls, clog the dowels and install studs for fasteners. The depth of screwing the studs should be such that the device is reliably fixed, but at the same time he was freely placed on fasteners. As a rule, all the necessary parts are included in the shell. When installing them, you need to use everything so that there are no extra details.

Scheme: Washbasin Installation Height in Bath

Shell height over washing machine

If under the sink it is planned to put the washing machine, then the model of the "water lily" is suitable. Its plums is equipped so that there is enough space under the sink. There are two types of drain: the first is directed back, and the second is down.

The design of the first type leaves more space for the machine, however, frequent blocks are possible due to bends. The plums directed down, designed so that the water should normally pass through the pipes, but the sink will have to be placed above the typewriter. The height of the placement of Santhpribor is calculated individually.

So that the sink is more convenient to use, it can be pulled a little forward from the wall. Then, when washing, a person will not rest on his legs into the machine. Such a simple reception will allow you to maximize the useful area without prejudice to the comfort of operation.

Scheme: Installation of a washbasin over a washing machine

Stage # 2: Connecting to the water supply

To install the mixer in it, the fastener is inserted into it, then the hoses for water are connected and gently tighten so that they are fixed tightly, but not excessively. Next set a sealing gum, washer, nuts (they are tightened by a wrench).

The main thing is that after installation the mixer was located correctly: its nose must be placed at a right angle to the wall on which the sink is mounted. You should also pay attention to the tightening of nuts. When the mixer is already fixed, they will not be tightened tighter, so you need to do everything at once and check.

Mixer for washing in the kitchen

Master Class Installation Mixer

Stage # 3: Mounting washbasin to the wall

When the mixer is already installed on the sink, it must be attached to the wall and finish connecting to the water supply. For this, the device is worn on the prepared fastening studs, install plastic liners, which are supplied in the kit, and tighten the nuts. If under the sink is provided with a support, then put on it.

Under the crane should be a sealing rubber gasket. It is placed above the nut. The seal does not prevent the nut in the future, so it's not worth tightening it too tight. If, when checking the connection, the crane will leak, just tighten the connection tighten.

Stage # 4: Connect washing to sewage

How to connect a washbasin to sewage? This stage is final. The siphon is connected to the plumbing device to which the pipe is attached - corrugated or rigid with bend. Then the pipe is connected to sewage. If its diameter does not coincide with the sewer release, a special rubber adapter is used.

When the work is over, it remains only to check the tightness of the connections. For this, the cranes open and spend on pipes with dry hand or a white napkin. If everything is fine and no leaks, plumbing is ready for operation.

Connecting a siphon washing to sewage

Siphon selection - important nuances

The normal operation of the plumbing is possible only if the siphons are correctly selected for sinks and sinks. Otherwise, you can encounter the problem of constant blockages. Distinguish several types of devices:

• Pipe. These siphons resemble the letter S or U, there are collapsible or unintended. The lower part provides a special cork, delivering which, you can easily clean the siphon. When installing a pipe siphon, it is important that the washbasin and input to the sewage system coincide.
• Bottled. Siphon got its name due to the part in which the hydraulic was placed. It resembles a bottle in shape. Siphon connects with sewage with a straight or flexible tube. The device is compact, easy to care: it is easy to disassemble and clean it. The disadvantage is that it is often necessary to clean, because due to the complex shape, the siphon is often clogged.
• Hidden. This is a variety of bottle siphon. When installing, only part of the structure (tube) is visible, and the second part (bottle) is installed in the wall. Such siphons are quite expensive and complex in the installation.
• Corrugated. The siphon is made in the form of a flexible tube, which is suitable for all types of washes. Such devices are cheap, easy to install, but their inner walls quickly turn fat, soap residues, and the pipe cannot be disassembled.

Pipe S-shaped and bottle siphons

What option is better to stop

To install under the sink in the kitchen it is better to choose a pipe siphon in the form of the letter S, because The elements of the sewage are often clogged with fat and kitchen waste, and such a device is easier to clean. For a washbasin, you can choose both a tube and a bottle siphon, because here the sinks are less often. If access to the device is free, even if it is clogged, it is easy to solve the problem.

As for the materials, the siphons can be made of polyethylene, polypropylene, brass or bronze. The most reliable models are metal, but polypropylene compete successfully with them thanks to a lower price and acceptable quality. In addition to the form and material, when choosing, the diameter of the neck should be taken into account, the presence of overflow and design, if the model is not closed with a tumbel or leg of the sink.

Video: How to connect a sink to sewage

In the process of connecting the washbasin and sinking to sewage should not be too strongly tightening the nuts. It can negatively affect the state of rubber pads and before the time to bring them out of order. If the connections are reduced, the gasket can be removed, dried, handle the sealant and reinstall, and tighten the connection.

Install and connect the sink in the kitchen - it seems there is nothing easier. However, this impression is deceptive. It can be felt as soon as you start connecting the sink in the kitchen alone. It was then that a lot of questions appear and float various nuances.

Today, several types of kitchen sinks used, which differ in the installation method, have different operation. Connecting washing is also individually, but there are still general rules.

Main varieties

1. Group of overhead mooles. This species can be safely attributed to the simplest. Connect products are quite simple, they do not require large cash investments. The sink of this group simply puts on a separate bedside table and plays the role of the tabletop.
2. Mortise sinks. This species is called so due to the fact that it is inserted into the previously prepared hole done in the tabletop. As a result, we have a mortise sink with a fairly attractive appearance and appropriate amenities.
3. Podstolian sinks. Basically are installed in countertops made of stone, various solid material or wood.

This makes it possible to obtain excellent sealing, the moisture will not fall under the sink, therefore, the swelling of the countertops will not occur. However, it should be noted that the cost of such shells is always very high.

Back to the category

Connecting mortise sink

Plumbing like a type is made of a variety of materials. They have a variety of dimensions and differ in their shape.

In the event that the headset of the countertop is made of chipboard, any man can perform an independent installation of such a mortise sink. With a stone countertop, everything is more complicated, it will take help from specialists who have the necessary equipment. Consider how you can independently mount this sink in the kitchen.

Starting to mount mortise sink is necessary from the manufacture of the hole you want to do in the tabletop, given its size. For this purpose, the sink pattern is placed on the worktop, focusing on the place where the hole will be. The pattern is equalized and fixed by painting tape.

You may be interested: Connecting a kitchen mixer

The set pattern is delineated by a pencil over the entire contour. After that, the second outline is drawn at a distance of 1.5 cm from the first. It is for him that will need to cut a hole.

For cutting holes, an electrolovka is used.

To cut the cutting smoothly, it is necessary using an electric door, to make a special initial opening in the table top, it will include a jigsaw blade. The diameter of the drill for such an initial opening must be 12 mm.

1. In the drilled hole, the blade of the jigsaw is installed, with which the cutting of the hole itself is carried out. Moving along the contour drawn, everything needs to be done, neatly and measured.
2. The next step will be the processing of the edges of the table top with a special silicone sealant. Its use will help create protection against water from entering water. The sealant should be well frozen. Like a few hours.
3. Insert the sink into the resulting hole, look at how dense the sink sinks come into contact with the worktop.

At the same time, you need to check the connection of the mixer, all summarizing communications. The fact is that after the final installation of the sink, it will be very difficult to hold all hoses.

Back to the category

How to fix the sink?

To carry out such an operation, you need to top up the table top right at the edges to impose two-way tapes, which comes in conjunction with the sink. In the absence of tape, a special sealant is applied again. The sink should be included in the pressed hole on the press landing, the voids formed should be filled with a sealant.

When the sealant is completely driving, the shell is fixed with special fasteners. This operation must be performed in a specific sequence.

First, the angles located on the diagonal are attracted, the reserve is left to the final tightening. Then the details are attached in the middle. The extra sealant needs to be carefully removed after it completely freezes.

Back to the category

How to connect the sink in the kitchen?

First you need to connect hoses to the water supply system through which water will be supplied.

1. A rubber gasket is installed between the fastening nut and the mixer, its task is to provide an excellent seal.
2. After connecting to the water supply of all hoses, the washing is connected to the sewage system with compliance with a specific sequence.
3. First, the siphon release is fastened in the sink. After that, a rigid pipe with a turn is connected to it. This pipe is fixed in the sewer output.
4. After connecting and connecting all communications, the reliability of the connections is checked, the leaks should not be.

You may be interested: How best to hide hood in the kitchen