Installing a modern toilet. How to install and connect to the sewage toilet: instruction and video

In cases where there is a desire to save on the services of specialists, or simply learn a new construction skill, information is useful about how to properly install the toilet.

What you need to install

Before installing the toilet with your own hands, you need to take care of the availability of a number of tools:

perfederator or shock drill;
drive with a diameter of 8-10 mm (depending on the diameter of the dowel fastening of the toilet);
kaffle drill (if the installation is made on the tile or ceramic slab);
adjustable key;
set of wrenches;
a hammer;
sealant (either in a special tube, or with a gun for sealant);
screwdrivers (flat or cruciform, depending on the design of the toilet);
100 × 100 rubber loan cuff (if you need to connect to the cast-iron calculation);
a set of fasteners for installation of the toilet (if it is not included);
ragged and capacity for draining the remaining water from the old toilet.

Before installing the toilet, it is necessary to make some preparatory work. For example, you need to decide what exactly to connect the new toilet to the sewage sewage. Options are possible:

Corrugated cuff. This method is most economical, but in this case, the toilet cannot be attached close to the conclusion. It matters if the bathroom is small.
Straight cuff. Firmly and hermetically combines a bowl of design with a sewage system.
Eccentric cuff. Convenient if the system connection centers and the termination are shifted.

It is further desirable to replace the old flexible liner for water. The selection of the eyelid is based on how the distance from the compounds on the pipe with cold water to the compound of the airborne toilet mechanism. To this length should be added 15-20 cm.

If necessary, you need to pre-purchase adapters for threads in places of connection from flax or fuma tape.

In the case when a wooden stand is preserved under the old toilet, it must be deleted. It will help in this nail or puncher. It is possible to close the resulting emptiness with a cement composition, preferably fast frozen, and a spatula.

Dismantling of old toiletza

First you need to overlap water. Disconnect the flexible liner, pull the water from the toilet.
Then you need to turn off the drain tank. You can carefully, and you can use the hammer (if the old toilet is no longer needed).
You can quickly remove the toilet with the help of hammer and perforator.

Carefully so that the fragments do not fall into the sewage system, apply the tools in the place of mounting the toilet to the floor and the joint of the sewage device. Then the old bowl must be removed, thickening the water that remains.

Wooden board removal and floor alignment

After the old toilet is removed, you need to thoroughly clean the seawrage of the sewage from dirt and rust. Set into the nickname rubber transitional cuff 123 × 100, pre-covering the sanitary sealant.
Then plug the hole with a cloth, so that the smells do not interfere with further work.
Next, you need to remove the wooden board and pour the resulting emptiness with a remission.
Align over the floor with a spatula.

Marking and installation of dowels

The bowl of the new toilet to put on the planned place. Make markup through holes in the bowl on the floor, in order to see where to drill. The holes in the bowl of the toilet bowl are located at an angle, in which case the drill is also at an angle.
By marking, the toilet can be removed. Next, you need to drill holes in previously planned places and insert a dowel.

Fastening a drain tank toilet

In accordance with the instructions attached to the toilet, it is necessary to establish the reinforcement of the drain tank. This procedure exists some features.
Tighten the nuts of the drain and fuel valve are manually, while while holding the valve itself, thereby protecting it from turning and the possibility of damage to the gasket.
Valves should be installed so that during operation the movable elements did not hurt each other and the tank walls.
In case of uncertainty, a sanitary sealant should be applied as the walls of the tank and pads.

The drain mechanism is released collapsible to facilitate the installation process.

Installing bowls toilet bowl

The connecting cuff is fastened with a petal part for a transitional cuff 123 × 100, inserted into a sealant previously treated with a sealant. The output of the bowl of the toilet is inserted into the transition cuff until it stops.
The cuff should be checked so that the toilet bowl accepted the smooth position, and all the openings of the fixtures coincided.
To the surface of the floor, the bowl is fixed with screws with plastic washers. In cases where the surface of the floor is uneven, you need to use gaskets from plastic pieces to align the toilet before you finally tighten it.

Connection of the bowl and drain tank

Before installing a drain tank on the construct bowl, you need to put the gasket between them. For reliability and avoiding the gasket, it is better to glue it to a sea sealant in advance.

Securing the tank on the bowl, evenly tighten the screws. After that, set the tank cover and the plum button. Then secure the flexible eyeliner.

Checking the functioning of the system

At the end of all the work, you need to check - dial water into the tank and make a trial drain. The amount of water drained can be adjusted, how to do it is written in the instructions.

Inspect all the elements on the absence of any leaks. If they arose, check the tension strength and, if necessary, disassemble the node, reincarnated with sealant, then tighten as it should.

If the cause is a detail fault - purchase a new part and replace.

Set the seat of the toilet and fill the slots between the toilet and the surface of the floor with a sealant.

It is not difficult to fulfill this work, if you adhere to the above recommendations and rules. Good luck!

How to install the toilet with your own hands - step-by-step instruction with video

What is needed to install the toilet bowl. Step-by-step instructions for dismantling the old and setting of a new toilet with their own hands

How to install the toilet with your own hands

From our article you will learn how to install the toilet with your own hands. This is a fairly simple operation, provided that you are able to overlap the flow of cold water, and the feed and sewer pipes do not need major repairs. In this case, we will install a toilet bowl with the bottom of the tank. This option is simpler, since most of the weight of the tank in this case falls on the toilet. When installing a toilet bowl with a top tank, reliable fasteners will be required to maintain the weight of the latter (for brick walls it is not a problem, but in the case of walls from hollow materials you will have to resort to special tricks).

1. If the height of the floor undertaken in the repairs undertaken in the repairs undertakes, the height of the floor has changed, it is necessary to compensate for the difference using the eccentric cuff - the so-called toilet corrugation (for sewage) and the flexible hose (for cold water supply). In the case of large changes in the height, professional plumbing skills will be required.

2. If the floor in the bathroom is not smooth enough, the toilet is better installed on silicone sealant. You can use small wooden / plastic wedges, but here without sealant can not do, because it allows you to evenly distribute the weight of the toilet.

3. If the sewer pipes go down, via the floor, and not through the walls, you will need a rectangular knee or a flexible corrugated cuff. This is not the only difference, but the main one.

Build and installation of a toilet bowl

2. Follow the manufacturer's instructions for assembling the insides of the tank. The sequence of actions depends on the type of drain system used in the model you selected.

3. Make sure that all the details are securely secured, but do not make excessive effort when tightening bolts and screws.

4. In most cases, a bolts for attaching it to the toilet are sold with a tank. Do not forget to wear the washers and rubber cone gaskets before inserting the bolts into the holes intended for them.

Installation toilet with a tank installed

6. Insert the corrugated cuff (corrugated extension cord) into the sewer pipe, making sure it is tight fit. Our example requires a simple direct connective cuff. (When connecting the toilet to the cast-iron pipe, you will need a transition cuff with a diameter of 110 mm. See photo. It must be abundantly lubricated with silicone sealant and insert a cast-iron pipe with a dirty tube. See photo. Only after that you can insert a corrugated plastic cuff into it.

7. Move the toilet to the sewer pipe. Make sure that its release is on the same level with the installed pipe. Most likely, it is. But if not and the offset is quite large, then you will need to use an eccentric corrugated cuff.

8. Gently install the toilet to the place intended for it, putting the cuff to the outlet.

9. Ensure that the tank is smoothly located with an alcohol level by placing the last one along the back wall. Through the rear wall of the tank, mark the places on the wall where the holes have to do for its fixation.

10. Do the same with the toilet itself: Check it with a horizontal view through an alcohol level and mark on the floor of the mounting holes, trying to be as accurate as possible.

11. Mark the pencil on the edge of the base of the toilet. Knowledge of the exact position of "legs" will be useful to you when you finish the preparatory work and begin the final fastening of the toilet.

12. Move the toilet from the wall. Drill the holes for fastening the tank, focusing on the labels on the wall. Pick up (including the material of the wall) and insert the dowels.

13. Drill holes in the floor in the points you marked. When drilling a ceramic tile, you will need a perforator and a drill on concrete. At the beginning of the clock, the pressure on the perforator must be not large, after passing the layer of the pressure tiles can be increased. Insert the dowels into the holes. If the floor is wooden, as in our case, they are not needed.

14. Before installing the toilet in place, apply silicone sealant on the floor along the marked line with a pencil corresponding to the border of the "leg" base.

15. Place the toilet in its place. Screw the tank to the wall, inserting between the screws of the screws and the tank wall of the washer. Do not overdo it, tightening screws.

16. Screw the base of the toilet to the floor. In this case, the same rules apply: first, do not forget about plastic washers, secondly, do not tighten the screws too tight.

Water connection and installation termination

17. Connect the tank to a cold water tube. Low probably, you will need a flexible connecting hose. The connection site depends on the position of the inlet pipe on the new tank.

18. Turn on the water by opening the shut-off valve, and make sure that there are no leaks in all connectivity places. Also check the tightness of the articulation of the toilet bowl with the sewer and wake all the compounds with silicone sealant.

19. Install the toilet seat, as it is provided by its design. If necessary, adjust the seat so that it exactly corresponds to the form of the toilet.

20. Apply silicone sealant around the base of the toilet. Complete all the irregularities with a wet sponge, achieving a neat look.

How to install the toilet with your own hands - step-by-step photo instructions

Follow our step-by-step instructions and you will learn how to install a toilet bowl with your own hands and what is necessary for this

Installing the toilet with your own hands

If you first thought about the installation of the toilet, this article is for you. And it is better if you have time to read it before it goes to the store for a new "faience friend" or before the start of the finishing finish in the room of the toilet.

The fact is that modern toilets are so different that they strongly differ the type of fastening, washing, the supply of sewage, etc. So, Ideally, plan what kind of toilet it is to be installed with your own hands, you need to start at the toilet design.

Installing the toilet with your own hands

And what to do if there is an old "throne" in the toilet - how to remove it, avoiding the world flood? We will also talk about this in the article. Features of the installation process, step-by-step guide and several tips from the masters will help save money and mount the toilet with their own hands without any problems.

Planning space indoor toilet

It is impossible to plan a comfortable toilet without taking into account the peculiarities of the toilet bowl, which is to be installed there.

To understand what exactly needs to be done, you need to know:

it is necessary to dismantle the toilet, which served his own and pursue the overhaul in the toilet (including cladding, repair and supply of sewer communications and the tie of the floor);
what are the dimensions of the new plumbing - whether it will not climb the space and whether it will allow you to relax to open your door;
what is the mount from your future toilet;
what is the method of draining to the toilet;
at what height you want to install plumbing.

If you know the answers to all these questions, it remains only to disassemble the old (if necessary) and the installation of a new toilet bowl.

Recall that the floor plumbing is divided into several types. It varies with the shape and its device.

The tank for plum is combined with a bowl of the toilet and independent (wall).

To the floor of the toilet bowls are fixed: on 2 and 4 point of attachment, on the corners.

Down with the old toilet!

Surely your toilet to be dismantled is not wall mounted, which means it is attached to the floor. Remove it from the toilet will be able to only 7 steps.

Turn off the water and drain it from the tank in the toilet.

Before breaking the toilet, you need to turn off the water supply and unscrew the tank

Dismantling of old toiletza

If the neck is disconnected from the pipe, and the toilet is glued with a solution to the floor, then it is necessary to take a chisel and neatly split the pedestal from the solution, can be parts

If there are no plans for the old toilet, and you escort it on the last path, then after swinging it can split a sledgehammer so that it is not difficult to endure it. You will also have to do in the event that it is cemented by the attachments of the old plumbing.

After dismantling the toilet, estimate the condition of the pipes in the room. Cast iron creates many problems, before installing the new plumbing, it is recommended to change them on plastic. Also, plastic pipes are very easy to facilitate the process of installing the toilet and wiring of sewer plots (by the way, you can also read on our own plastic pipes on our website).

Independent installation of plumbing "By steps"

Toiletz for normal operation is needed smooth, lined or specially prepared surface of walls and gender.

First, blocking the toilet with corrugations connect with the tap of the sewer pipe-rising. You can also use a hard pipe. The best option is if the blocking of the toilet is included in the riser without extension corrugations, etc. To seal a drain, we use a ring with rubber border. It is important to consider that the rubber does not tolerate on its surface of cement and similar sharews. But the sealant is quite suitable.

Installation of toilet - cuff

We take the cuff and apply silicone sealant and install it in the pipe

Then take the corrugated pipe and also apply silicone sealant

Install the corrugation in the pipe

Then gently injecting the toilet and install its output to the corrugated pipe seal

In order to wash water during washing floors, this place can be sealed with silicone sealant

Fix on the floor: 3 types of fasteners

The first option for floor installation is anchors laced in the screed. During the fill of the floor in place, where the toilet and its attachments will be located, long anchors are fixed. After the screed dry and the floor finish will be carried out, the toilet on the anchor. This is the most difficult way of fastening, as it is difficult to install an anchor so smooth that the toilet to get on them without problems. It often happens that inexperienced builders choose too short anchor, for which then it is impossible to wind the nuts. The anchor mixed into the floor should be at least 7 cm above the finish surface to fasten the toilet to it. Under all nuts, gaskets are required so that the surface of the toilet is not lightering.
The second version of the reliable fastening of the toilet toilet on the surface at the surface of the toilet is an installation on a wooden basis. The main thing is that the board strictly coincides with the size of the toilet base. When pouring the floor, the board is prepared, scoring nails into it. Then it is placed in a solution with nails down. After drying the screed and decoration of the room, the toilet, pre-planted on the epoxy resin layer, is screwed to the blackboard using conventional screws. They also need rubber or polymer gaskets.

Fasten the toilet bowl with a wall tank without screws, one resin. True, with this method of fastening, it is necessary to predetermine the surface of the tile so that the glue holds better. When using "epoxies" it is important to give freshly installed plumbing to dry and fasten on the floor surface.

Mounting toilet to the wall

How to Install Installation

Outboard toilets are used more and more. The installation is not much more complicated by the usual (by the way, you can read on our own toilet installation on our website). Wall toilet, as it is clear from its name, will not have contacts with the floor surface. It is suspended with a metal frame, which is attached to the carrier wall itself. Tank and toilet pipes in this case are behind a false-wall from drywall. If the hinged plumber has an open tank, then it will turn it out on the wall itself, but then the sewer tube must be inside the wall. Hold the design will be the same anchors embedded in the wall or into the carrier frame.

Installing the toilet to the pedestal

After fixing the bowl of the toilet on the wall or on the floor, it remains only to collect a toilet. On the basis, the tank is already reliably fixed, the trumpet from the tank hanging on the wall is supplied to it.

Installing the toilet to the pedestal

It remains only to check whether the toilet works, and there is no leaks. We turn on the cold water, we wait until the tank is filled by adjusting the level of filling. We configure the instructions to the locking mechanism. We wash and look, does not flow from plum.

The last action is to fasten the stoolchak. But here you are probably already cope with yourself.

Before buying plumbing, first decide with the suggestive type of drain. If you do not plan to change the supply of sewage riser, you need to choose the same type that in the worker who has spent its toilet. Remember: no adapters will help you to qualitatively connect the toilet with an unsuitable type of removal.
Do not leave the choice and purchase of the toilet at the final moment of repair: it is better to prepare a place in the toilet in advance to facilitate the installation of plumbing.
Do not regret money on nickel-plated bolts and anchor for fastening the floor toilet or to the wall. They do not rust, which means, exclude ugly drips and bolts.

Installation of the toilet, with their own hands, was successful

Installation of the toilet with your own hands - step by step instructions!

Find out how the installation of the toilet is performed with your own hands. Step-by-step instructions, lessons, photos + video and best advice from professionals!

How to independently install the toilet

Having "straight" hands, most of the work on the house can be made independently. This category of work includes the installation of the toilet. Knowing a sequence of action installation or replacement can be made with your own hands.

Installation of the toilet with your own hands - the task of the average difficulty

Types of toilet bowls

In this article, we consider consider not the peculiarities of the washes or shape of the bowl, but those, features of the design, which determine the list of installation work.

By Montaja method

The toilet itself consists of a plumbing bowl and a drain tank. A bowl may be floor mounting or suspended. If the bowl is suspended, then the tank goes hidden editing - built into the wall. In the case of an outdoor bowl, there are three versions of the tank mounting: on a special shelf on a bowl (compact), separate, connected with the help of a flexible hose, in installation (hidden in the frame wall).

Typical dimensions of toilet bowls of different designs

The dignity of the outdoor toilet with a conventional drain tank is the simplicity of installation. It can be installed not starting repairs. The disadvantage - compared to the suspension, it takes more space, looks more heavy. Accordingly, there are complex models in the suspended models - it is necessary to fix the supporting structure - installation - in the wall. Perhaps this is only during repair.

Issue in sewer

The choice of toilet bowl in the sewer depends on the location of the sewer pipe. They are:

with horizontal release;
oblique release;
vertical.

Types of issues (outputs) toilet bowl

If the pipe is in the floor, the optimal will be the vertical release. If the exit in the floor, but is close to the wall, it is more convenient than oblique toilet bowl. The horizontal version is universal. Using the corrugated nozzle, it can be connected to the wall and in the floor.

Installation of a toilet bowl with a bunch of compact (outdoor option)

From the store usually brought separately bowl of toilet bowl, tank, drainage device and float. Before installing toilet bowl, everything except the float must be collected.

What is the floor toilet with a Bach type "Compact"

Begins the process from the installation of a drain device. It goes in the assembled form, it is only required to install in the hole in the bottom of the tank. A rubber gasket is stacked between the drain and tank.

We establish a drain mechanism inside the tank, putting a pre-rubber gasket

From the reverse side, the plastic washer is screwed into the nozzle. It is tightened with hands, then - using the key, but very carefully, as it is easy to break the plastic. So that the drainage device does not spin, it must be with hand.

Gently tighten the nut

The next step is to install fastening screws to the tank. They are also included in the staffing. These are long thin screws from galvanized or stainless steel. They are inserted into two small holes on the bottom of the tank, rubber gaskets put on, then the washers and only then screw the nuts.

Install the fastening screws on the tank

Before installing the tank on the bowl of the toilet bowl, the gasket (in the kit) is stacked under the tank. So that the smells did not smell from the sewage, it must be "put" on the sealant. We observe first on the one hand, we put on the toilet, we scroll on the other, put the tank.

We mark the gasket with Silicon, put on the toilet

Missing on the other hand

Install the tank on the shelf of the bowl, passing the screws into the appropriate holes. From the bottom to the screws wear washers, nuts, tighten. Make sure that the tank stood smoothly.

Install the tank on the bowl

Next, we put the float - the water level control device in the tank. At the top of the tank there are two holes. Here in one of them and insert the device. It is mounted on the side with which the plumbing will be connected.

Put in the tank float

On the outlet nozzle we swell a little flax, we wash the plumbing paste, set the corner (brass or stainless). Do not tighten the connection strongly, do not score that the plastic pipe.

Installation on the floor

The toilet almost collected, you can put in place. To the sewage toilet is connected using a corrugated adapter. At the ends, it has rubber seals that are tightly sit in the pipes and to issue a toilet bowl.

Corrugation to connect toilet to sewage

If the sewer tube is plastic, the corrugation is simply inserted until it stops. If the cast iron is still not new, so that the smell does not flick through the microcracks, the pipe is clean to metal, wash and dried. A layer of sealant is applied to dry clean metal around the circumference (at the bottom a little more), then insert the corrugation. For greater confidence, you can walk the sealant and outside the connection.

In order for the installation of the toilet to the old cast iron was a hermetic, under the corrugation you can lay a layer of sealant

In any case, insert the corrugation in the sewer tube.

Insert the corrugation until you stop

The second end of the corrugation is put on the release of the toilet. This is the connection to the toilet to the sewage. Everything is so simple. Only there is one nuance. To then be removed, the output of the corrugation and the release of the toilet is smeared with soap moistened in water, only the fools are put on. If this is not done, remove the toilet, without damaging the corrugation, it will be problematic. But you will have to drill holes under fasteners. It will be much more convenient to remove, and not try to move partially fixed instrument.

Nadiv Corrugation for the release, exhibit the toilet as it will stand. By installing a cover on the tank, check the place for it. Next, you need to sit down, check the comfort of use, if necessary, adjust the position. Then take a pencil or marker, inserting into the holes in the sole, mark the places for installing fasteners.

Celebrate places for fasteners

After removing the toilet, the openings under the dowel are drilled in the marked places. If the set is plastic fastener, do not use it - it will break in a few days. We must immediately put powerful dowels.

If the toilet toilet is installed on the tile so that it does not cracked, the glazed surface is better to put it. Take the touch, put in a mark, several times beat the hammer on it. This is called "Land". Then take a drill or perforator and drill the tile by turning off the shock mode. After the tile is passed, you can turn on the perforation mode.

Drill holes under fasteners

In the holes put plastic tubes from the dowels. They must be in the same plane with the floor. If there is a thicker edge, cut it with a sharp knife.

We swell the floor, removing the dust at the installation site of the toilet bowl. We put it in place, insert a dowel into the holes, twist them with the help of the corresponding key. Tightening the bolts must be alternately on the one hand, then on the other. Tighten until the toilet will become firmly without a backlash.

Latest barcode - connection to the water supply. Connect the output of the tap pipe with a crane installed on it with a bunch on a tank, which was previously connected. This requires a flexible hose. At its ends there are cape nuts (American), so that there will be no problems with the fastening. Tighten well, but without fanaticism.

How to install a suspended toilet with installation

To install hanging toilet bowls, the output of the sewer pipe must be located near the wall. The specific distance from the wall is indicated by the manufacturer, but must be small - from the far edge of about 13-15 cm. If the outlet out of the floor, there is a solution - a special pad, with which the stock is moved closer to the wall.

Installation of the suspension toilet begins with mounting to the frame of installation of the stops into the wall. They are attached two top and bottom. With their help, the distance to the wall is adjusted, the frame rises and starts.

Install the upper stops

The upper stops have the type of rods, are adjustable using an end key and screwdriver. The lower stops are more similar to the plates, they are also adjusted by the end key but with the side arrangement of the head.

Lower stops and height adjustment

The collected frame is attached to the wall, its center is exhibited over the middle of the sewer exit. The label on the frame rises or descends to the desired manufacturer height (there is a frame on the frame, also indicated in the passport, it is usually 1 meter).

Put in height and from the wall

With the help of a bubble level, the horizontal and verticality of the installation installation for the suspension toilet is checked.

Adjusting the height of the stops, an equal distance from the wall specified by the manufacturer is set. How it is convenient to do, look at the photo.

Set the set distance to the wall

The displayed frame must be fixed to the wall. In the appropriate places put marks with a pencil or marker, drilled holes. They are installed plastic hulls of dowels. Most of the suspended toilet bowls of imported production, and they recommend the hulls of the dowels to plant the sealant. In the drilled hole, some part of the sealant is squeezed, a dowel is inserted. Then, before installing the fastener itself, the sealant is superimposed in the plastic case.

In fixed installation, you can put connecting elements - nozzles, couplings. All of them are included, just fixed in their places.

Mounted nozzles and couplings

Tank and sewage pipes are installed

Next, metal rods are installed on which the bowl of the toilet will hold. They are screwed into the appropriate nests, on top on the silicone seals (on the bottom photo it is two rods over the sewer output).

Toilet holders are installed, sewage pipe is fixed.

The sewage pipe is put forward at the desired distance, fixed in a specified position using a bracket. It covers the pipe from above, inserted into the groove until it clicks.

Then water is connected to the tank. Open the tank cover (it is on latches), the plug on the side surface is removed. On the right or left - it depends on where the water is supplied. A corrugated pipe is inserted into the opening hole, the response part is inserted from the inside, everything connects with the help of a cape nut. It is necessary to delay without applying excessive efforts - it is plastic.

Connecting installation to water supply

A tee is installed inside the tank, the pipe is connected to the desired output (usually plastic). Do it with the help of adapter and American.

Connecting a tap pipe

A hose from the tank is connected to the special input of the tee. It is flexible, in a metal braid. Tightening with a cape nut.

Connect the hose from the tank

Install the lid. In principle, installation for the toilet is established. Now it is necessary to close it. To do this, make a falseland from moisture-resistant plasterboard. It is recommended to put two sheets, but one can and one. Hyposparboard is attached to the installation frame and to mounted profiles.

Fastening Fallest to the Frame of Installation MUST

The toilet is put on the pins, its release enters the plastic socket. The compound is sealed, additional measures are not required. This installation of the installation with installation is completed.

Installation of the toilet with your own hands: Outdoor, suspended with installation, instruction with photos, video

Independent installation of the toilet will save a solid amount of money. You can install an outdoor model and suspended with your own hands, with installation.

Plumbing equipment must be established in compliance with construction standards and rules. Knowing about it, many homemade masters experience insecurity in their abilities, and even a real fear.

They seek help in service companies that require decent money for their services. But the installation of the toilet is not so difficult at all, as it may seem.

There are several ways to install plumbing, we will analyze in detail each of them.

Method of installation of the toilet depends on the type of device and its structural features. You can find two main types of equipment, the technology of installation work in each case will be completely different. It:

Outdoor toilets. Mounted directly on the floor covering at the end of the finishing work indoors.
Hinged toilets. Installed using special fasteners at some height from the floor level. Installation of equipment is carried out before the start of repair work.

The floor toilet is installed directly on the floor covering. This is the most common type of equipment.

Hinged plumbing devices are installed using special installation structures to which the system is fixed.

Outdoor equipment can be mounted in two ways to mount to the floor:

internal, quite complex in execution, but more aesthetic;
outdoor when the mount is carried out with the help of special technological holes based on the device.

In addition, the method of installation of the plumbing device depends on the method of connecting to sewage. There are three options:

Horizontal edition. The device is connected to the sewer system exactly at right angles.
Vertical release. Sewer slurry for connecting the device must be in the floor.
Oblique release. Such equipment is attached to the fan pipe at a certain angle, most often its value is 45 °.

Consider in detail how to install the floor toilet with your own hands.

Connecting the device to sewage

To connect plumbing equipment to sewage, you can use various connecting elements:

Fan pipe. The shaped product from the midfarfor, faience or porcelain. It is quite difficult in the installation, used most often by professional masters.
Plastic pipe. Used when mounting the equipment, located close enough to the sewer pipe.
Eccentric. Plastic part consisting of two nozzles with displaced centers. The special structure of the eccentric allows you to connect the output of the toilet and the sewer pipe, even if the equipment is somewhat shifted. Detail is available in different sizes.
Corrugation. Flexible plastic device that allows you to connect any to the type of toiletz with sewage field. At the same time, the location of the riser or pipe, as well as the device itself can be any. Optimally suitable for self-installation of equipment.

Consider various ways to connect the toilet to sewage.

Method # 1: Fan tube or plastic pipe

Such a mount assumes that the shaped elements combine the release of the toilet bowl with the sewer. Please note that independent work with such elements can be quite complicated, especially if you don't get a toilet to the riser at the desired distance due to some reasons.

In this case, you will have to use other connecting elements or invite specialists. If the sewage hole is convenient and the toilet to it is suitable, the work can be performed independently.

With the help of plastic connections, you can perform any complex configuration required to connect toilet bowl. When installing such a system, do not forget about special rubber seals

When installing a vertical or horizontal connection, it is important to use special rubber seals: cuffs, inserts, etc., which should go bundled with connecting elements. Details provide a reliable and dense connection, however, for insurance you can additionally use the sealant.

We substitute the sanitary device to the location of the connection and insert it output into the sewer, not forgetting about seals and sealant.

After that, the toilet can be mounted to the floor.

If it is decided to connect the toilet to the sewage with the fan pipe, it must be remembered that the release of equipment and the seven-tube must be perfect to each other. Displays the device will not work

Method # 2: Eccentric

When connecting to sewage using eccentric sealant, it is not necessary to use a sealant, since the form form provides the necessary tightness. The output of the eccentric cuff is inserted into the sewer. It is important that the diameter of the part was selected correctly.

Eccentric allows, if necessary, disintegrate a little to the toilet relative to the riser, but this distance is small.

For reliability, it is still possible to wove the place of connection with silicone sealant. We substitute the toilet and put on its conclusion the second end of the cuff. Equipment can be mounted to the floor.

Method # 3: corrugation

The simplest of all methods allowing you to connect the riser and the toilet of any type if necessary. We wipe the rifle corrugation. The wavy strip is abundantly applied silicone sealant on the ribs of the rubber band, which will later be hidden in the sewer tube.

We spend the same operation from the opposite edge of the corrugations, processing the site that will be on the neck of the toilet bowl.

We insert the corrugation into the sewer fool and wear the second end of its end to the equipment. Highly press plastic fingers, controlling the reliability of the connection.

The easiest way to connect the toilet to the sewage using corrugations. The element can be stretched and give it the necessary form, so without any problems, equipment of any type is connected

Installing a bowl of an outdoor device

Depending on the method of attaching the toilet to the floor, the connection of the device to sewage can be carried out up to this point or directly during this operation. Installation of the toilet begins with the installation of the bowl, which can be performed in different ways.

Method # 1: Installation on a dowel

First, we prepare the basis for which the equipment will be installed. The floor must be absolutely smooth, without the slightest drops. Otherwise, the device will rise unevenly and will be loosened when used. If you plan to put a ceramic tile on the floor, you need to do it before starting the installation work.

Uninstalling the united toilet can be lining, but this is a very time-consuming procedure that requires an accurate trimming of each tile. It is much easier to spend all the necessary events in advance.

In addition, we need consumables to work, which will need to purchase drills for glass and for concrete and silicone sealant.

When performing a pencil markup, keep strictly vertically to mark the point under the mounting hole as much as possible

Consider in more detail the external method of fastening the device. We carry out work in the following sequence:

We start with fitting. We put the toilet on the base prepared for it and control the angle of inclination, the coincidence of the height of the sewer tube and the neck, etc. If we find any inconsistencies - they are quickly eliminating them.
We carry out markup. To do this, first determine the central axis of the toilet. Optimally, if it passes through the center of the room. Focusing on it, we install the device at a distance of about 15 cm from the sewer termination. We take the marker and carefully circuit the contour of the device. Strictly vertically insert the marker into the technological mounting holes and put the labels under the opening.
Cooking holes for fasteners. We remove the toilet to the side and, perforator or drill, carry out the necessary holes. If the tile is laid on the floor, first take the drill on the glass, drill the facing, change it to the drill on concrete. Thoroughly clean the hole from dust and pour silicone into it. It will perform the role of the waterproofer. Then we insert plastic dowels.
Install the toilet. We laughed in advance to the instrument in advance. We put on it a special rubber gasket or abundantly apply a silicone layer that will perform the role of gasket. We put the equipment in place and pressed it to the floor. Insert the sleeves in the mounting holes and tighten the screws carefully, fix the plugs. Silicone surplus remove a wet finger or rubber spatula.

Spin the fasteners extremely neatly. Excessive force may result in a damage of equipment on which cracks may appear

The device with the inner fastening will be set somewhat differently. Before installing it, you must make sure that all the outlet openings of engineering systems are connected under the toilet. Installation is carried out as follows:

Fixing system connect to the toilet body.
We carry out markup. We put the device to the place that is intended for it, and supply the contour with a marker or a simple pencil. We remove the equipment and inside the resulting circuit we plan holes under the fasteners, not forgetting that each connection is fixed on the floor two bolts
We carry out the necessary holes. On the tile, we first work the drill on the glass, then the drill along the concrete. In the holes fill the sealant and install the dowels.
Fastening screw to the floor bolts. We take the toilet, put it on the installed fasteners, and fix the bolts through special side holes. It is not necessary to delay the fastenings. It is possible that in the process of connecting the device to engineering systems, you will need to carry out small adjustments.

Look more on video:

Method # 2: Montage for glue

If, due to different reasons, the bowl of the toilet can not be installed on the dowel, you can carry out installation on glue. The method is suitable only for smooth floors. For the operation, you will need a high-quality adhesive composition. It can be liquid sealant, silicone glue or epoxy resin with various hardeners.

You can make such a composition yourself. To do this, take 100 parts of ED-6 epoxy resin, heated to 50c, add 20 parts of the solvent or plasticizer, well stirred. Then we pour 35 parts of the hardener and prevent well again.

In the resulting mass we introduce 200 parts of cement and mix to obtain a plastic homogeneous mass.

Installation work performed in the following sequence:

We carry out markup. We put the sanitary appliance to the place intended for it and supply the contour pencil.
Preparing the basis. First of all, we carefully clean the floor and the base of the toilet from possible contaminants. To improve adhesion with adhesive composition, it is necessary to give the surface roughness, so we clean it with an emery skirt. After that, degrease the base of the device and the floor by any solvent or acetone.
Exactly following the manufacturer's instructions, we prepare the adhesive composition for work.
Gently apply glue to the inside of the bottom of the toilet and inside the contour, scheduled on the floor. The layer of composition should be not too big.
We put the toilet to place and strongly press it to the floor surface.

After we glued the device, you need to wait until the glue does not dry. It usually leaves about 12 hours. During this time, the equipment should not be touched, especially to sit on it.

Otherwise, it can shift towards, and the fastening will be not solid enough.

Before installing the toilet bowl, we definitely determine the base of the plumbing device and the floor under it sandpaper, creating a rough surface

Method # 3: Installation on your taffeta (wooden gasket)

The method appeared to install plumbing equipment on the wooden floor, but can also be used for other types of coating. To properly install a toilet to the toilet, you need to perform the following operations:

Cooking your taffeta. This is the name of the gasket made of durable wood, to which the plumbing device is attached. Cut it from the board with a thickness of 2.8 to 3.2 cm. The workpiece is well process with a olifoy or any other solution against rotting. So that the support rack is securely attached to the floor, fix an anchor in it. The easiest all in checkelling to fill nails in such a way that they oppose the board by 2-3 cm.
In the floor we make a recess to install the device. Its shape and size must match the taffeta. Pour the deepening of cement mortar.
I turn down the taffeta anchors down and blend it into cement. If everything is done correctly, the board must be flush with the floor. We are waiting for complete drying of cement.
Getting to install the equipment. We put the toilet to the taffette and fix it with screws, lubricated graphite or tavot, so that they can be easily unscrewed. Under the heads of the screws, we definitely lay the rubber washers-pads so as not to damage the ceramics.

In addition to the traditional wooden taffeta, you can use a rubber substrate. For these purposes, a sheet material is 5-15 mm thick.

It is possible to use an old rubber rug.

For taffeta, it is best to take durable wood type ash or oak. Be sure to process the part of the oil or another composition protecting the tree from rotting

Installation of a drain tank and connecting to the water supply

After the equipment is fixed, you can start the installation of the drain tank. There are two varieties of this device, consider the features of the attachment of each.

Installing a drain tank on the regiment of the toilet

Such equipment is easy to be mounted. In this case, it does not matter when the internal elements of the tank are installed: before or after mounting the devices on the shelf. In general terms, work is performed as follows:

We put the tank in place. Pre-take special rubber gaskets and lubricate them on both sides with silicone for better sealing.
Gaskets Let's put on the toilet shelf exactly above the drain holes and install the tank.
We bind the shelf and tank with bolts. We wait until Silicone is frozen. This will require 15-20 minutes.
We check the tightness of the resulting connection. To do this, pour water into the tank and see whether the leaks appeared. If the shortcomings are revealed, eliminate them.

After we installed the drain tank, proceed to the installation of its internal elements:

We connect to the tank clutch clutch.
Attach the float valve to the coupling.
We screw the tube overflow.
Mount the water descent lever.
Install the saddle and vertical valve.
Through the thrust we combine the mechanism of water descent and the vertical valve.
Fix float valve.
Adjust the twist of the float knee by installing the desired angle. The less angle, the less water will flow into the drain tank.

Do not forget to adjust the seat of the saddle - many forget about this moment!

Before installing a drain tank on the toilet shelf, be sure to mount special gaskets, providing the system necessary tightness

Construction with a tank fixed above toilet bowl. Its installation is made in this way:

After the plumbing device is installed, we bring the drain pipe from the tank to it.
Fix the pipe to the toilet, using a special coupling.
Considering the height of the drain pipe, we plan on the wall of the attachment point of the tank.
Disconnect the tube from the tank, after which we install the equipment on the wall. Reliably fix it. We put the drain pipe into place.

After the installation of the tank is completed, proceed to the installation of its internal elements:

Mount the trigger lever.
Fix the vertical valve, saddle and overflowing mechanism.
Vertical valve, overflow and trigger combine using thrust.
We bring the tap pipe to the tank and fix its clutch with the mandatory use of rubber gasket.
Fix on the coupling float valve.
Under the desired angle, connect the twinge of the float knee with the valve.
Adjust the seat position.
Correct the location of the coupling, which connects the toilet and drain pipe.

To connect the drain tank and tap pipes, use the flexible hose of the desired length.

After the connection to the water supply is completed, be sure to test the device. We recruit water into the tank and wash off. Control all the mechanisms. If problems are revealed - immediately eliminate them.

The mounting height of the attachment can be different. It depends on the model of sanitary equipment

Mounting cover toilet bowl

The last stage of the flooring of the floor toilet with their own hands is the installation of the seat and covers. This is a very simple operation. Included with the seat already go special fastes, as a rule, they are made of plastic.

Such details are very easy to unscrew and twist. In addition, the increased humidity does not harm plastic elements.

Another plus - the design with plastic fasteners is less moved along Sanfayins. We apply the cover to the toilet so that the attachments are included in the grooves intended for them.

We shift the whole design forward and tighten the nuts tighten, locking the seat in this way.

So that the cover of the toilet and the seat do not slide over the surface of the toilet bowl, you need to tighten the fastening well

Independent installation of toilet bowl - the case is quite sat for a home master. It is important to correctly determine the type of device and, in accordance with this, select the optimal installation method.

It is important to carefully read the instructions from the manufacturer of the equipment, where the installation procedure is described in detail, and in the process of conducting work strictly observe it. If you fulfill all these conditions, the equipment installed by your own hands will work for a long time and without problems.

In cases where there is a desire to save on the services of specialists, or simply learn a new construction skill, information is useful about how to properly install the toilet.

What you need to install

Before installing the toilet with your own hands, you need to take care of the availability of a number of tools:

perfederator or shock drill;
drive with a diameter of 8-10 mm (depending on the diameter of the dowel fastening of the toilet);
kaffle drill (if the installation is made on the tile or ceramic slab);
adjustable key;
set of wrenches;
a hammer;
sealant (either in a special tube, or with a gun for sealant);
screwdrivers (flat or cruciform, depending on the design of the toilet);
the 153x100 rubber cuff (if needed to connect to the cast-iron termination);
a set of fasteners for installation of the toilet (if it is not included);
ragged and capacity for draining the remaining water from the old toilet.

Before installing the toilet, it is necessary to make some preparatory work. For example, you need to decide what exactly to connect the new toilet to the sewage sewage. Options are possible:

Corrugated cuff. This method is most economical, but in this case, the toilet cannot be attached close to the conclusion. It matters if the bathroom is small.
Straight cuff. Firmly and hermetically combines a bowl of design with a sewage system.
Eccentric cuff. Convenient if the system connection centers and the termination are shifted.

If necessary, you need to pre-purchase adapters for threads in places of connection from flax or fuma tape.

Video - Independent Installation of Toilet

Installing the toilet with your own hands

First you need to overlap water. Disconnect the flexible liner, pull the water from the toilet.
Then you need to turn off the drain tank. You can carefully, and you can use the hammer (if the old toilet is no longer needed).
You can quickly remove the toilet with the help of hammer and perforator.

Wooden board removal and floor alignment

After the old toilet is removed, you need to thoroughly clean the seawrage of the sewage from dirt and rust. Set into the nickname rubber transitional cuff 123x100, pre-covering the sanitary sealant.
Then plug the hole with a cloth, so that the smells do not interfere with further work.
Next, you need to remove the wooden board and pour the resulting emptiness with a remission.
Align over the floor with a spatula.

Marking and installation of dowels

The bowl of the new toilet to put on the planned place. Make markup through holes in the bowl on the floor, in order to see where to drill. The holes in the bowl of the toilet bowl are located at an angle, in which case the drill is also at an angle.
By marking, the toilet can be removed. Next, you need to drill holes in previously planned places and insert a dowel.

Fastening a drain tank toilet

In accordance with the instructions attached to the toilet, it is necessary to establish the reinforcement of the drain tank. This procedure exists some features.
Tighten the nuts of the drain and fuel valve are manually, while while holding the valve itself, thereby protecting it from turning and the possibility of damage to the gasket.
Valves should be installed so that during operation the movable elements did not hurt each other and the tank walls.
In case of uncertainty, a sanitary sealant should be applied as the walls of the tank and pads.

The drain mechanism is released collapsible to facilitate the installation process.

Installing bowls toilet bowl

The connecting cuff is fastened with a petal part of the transition cuff 123x100, inserted into a sealant previously treated with a sealant. The output of the bowl of the toilet is inserted into the transition cuff until it stops.
The cuff should be checked so that the toilet bowl accepted the smooth position, and all the openings of the fixtures coincided.
To the surface of the floor, the bowl is fixed with screws with plastic washers. In cases where the surface of the floor is uneven, you need to use gaskets from plastic pieces to align the toilet before you finally tighten it.

Connection of the bowl and drain tank

Before installing a drain tank on the construct bowl, you need to put the gasket between them. For reliability and avoiding the gasket, it is better to glue it to a sea sealant in advance.
Securing the tank on the bowl, evenly tighten the screws. After that, set the tank cover and the plum button. Then secure the flexible eyeliner.

Checking the functioning of the system

At the end of all the work, you need to check - dial water into the tank and make a trial drain. The amount of water drained can be adjusted, how to do it is written in the instructions.
Inspect all the elements on the absence of any leaks. If they arose, check the tension strength and, if necessary, disassemble the node, reincarnated with sealant, then tighten as it should.
If the cause is a detail fault - purchase a new part and replace.

Finishing stage

Set the seat of the toilet and fill the slots between the toilet and the surface of the floor with a sealant.

It is not difficult to fulfill this work, if you adhere to the above recommendations and rules. Good luck!

Although the services of a plumbing specialist services are much simpler, many are currently coping with the problem of installing the toilet independently. With the production of plastic pipes and fittings, work on laying pipelines and installation of plumbing equipment switched to the category of "clean", their installation was significantly simplified, the compounds were stronger and more reliable, the equipment is durable.

It is of great importance to such a factor: the toilet is established for the first time or in return obsolete. When equipped with a new sanitary room, it is possible to schedule the installation of the toilet bowl of any design, it will not be necessary to fit into the already available limited space. In any case, having small skills to work with instruments and a desire to actually cope with both tasks.

Selection of toilet

When it comes to choosing a model, the price is no longer about the quality and design, but about the material from which they are made and design. Quality can guarantee a reliable manufacturer. The most worthy of the Russian factories in Kaluga and Stary Oskol have proven themselves in the market. The cost of the toilet can satisfy the needs of any buyer, it fluctuates from 2 thousand rubles to several thousand dollars, and their installation occupies from thousands of rubles and more.

Depending on the structure of the toilet, there may be:

Traditional outdoor
Suspended

Pendant are usually installed in bathrooms with limited space. In this case, the tank can be mounted directly into the tap pipe.

Outdoor products are provided by a wide range, excellent in shape and manufacturing material. If it allows the area, it is desirable to install, except for a toilet-bid, and choose the instruments that will be harmonized in color and design.

Toilet bowls are made of various materials:

Steel
Cast iron
Porcelain
Faience
Glass
Plastic

The most common from porcelain or ceramics. They have time to 50 years. At the request of the client, they can be made of exclusive materials: wood, with precious metals and inlay.

By design, they are divided into:

Vertical
Horizontal
Kosovo

The type of drain affects the shape and size of the toilet.

Currently, there are for sale toilet units that combine the function of the bidet and with a heated seat.

Having stopped at the model, fully relevant to the requirements and material capabilities, checking the staffing accessories, you can start installing the toilet bowl. If necessary, first need to dismantle the old one.

Dismantling of old toiletza

To dismantle the toilet, you will need a set of most primitive tools:

A hammer
Chisel or chisel
Passatii

The old toilet usually have to change due to its malfunction or in order to replace the more modern. If in the future it will not be needed for installation, for example, in the country, dismantle the old will not work out any difficulty. Before proceeding with the dismantling, it is necessary to rinse it thoroughly and disinfect. In his bends, a large number of lime plates, dirt and microbes have been accumulated.

It is necessary to work in rubber or silicone gloves and protective glasses. They protect eyes and hands from possible fragments and chemical effects of antiseptics. Under hand there must be water and rags.

Dismantle to the toilet, which was screwed to the board with metal screws, in the future robbed, retaining its integrity, will not succeed. Therefore, it is roughly closed from the sewer tube, the residues with the help of the passage and the chisels are neatly removed. In a siphon, which serves as a water shutter and does not allow the penetration of poor smell into the bathroom, water remains approximately two liters. She is going to rags in a bucket or a basin.

Recently installed toilet with the use of plastic screws is difficult to dismantle. Difficulties are that they are screwed straight to the floor, and to save the floor and do not hurt need to act very carefully. From the tee of the sewer pipe, the toilet is removed easily.

Installing a new toilet on tiled floor with screws

Included with the toilet there is always an installation instructions. In the case of a complex design, the circuits of connecting nodes and fasteners are shown. Carefully examining it, you need to cook tools:

Passatii
Drill with kits drilled (the perforator is not suitable)
Spanners
Level and roulette

In addition to tools, you will need silicone, mounting gun to work with it, pencil, chalk or felt-tip

You need to start with the adjustment of the float valve in the tank. While it is not fixed and access to its components is unlimited, it is necessary to adjust the valve in such a way as to further eliminate the leakage of water. This is especially important in cases where the drain tank is mounted directly into the plumbing pipe. If you lower the float down, the water flows less, if you raise it - it can be poured through the hole of the overflow. Normally, water must be at the level of 5-7 cm. Below the safety plum.

The order of installation of the toilet with their own hands, regardless of the design and brand, is made according to the same scheme.

The preparatory stage consists in stripping the sewer and floors in the bathroom.
A corrugated tube dresses on the release of the toilet.
Installation on the tile requires special caution: it is necessary to preserve the tile and toilet. To do this, the floor under the height of the instrument cleaned from the garbage should be put the sheets of cardboard, rags or a special gasket, which are equipped with some models. The toilet is neatly descended to the connection site.
Several times carefully refineed the final place of installation, on the contour of the landing plate, you need to draw a marker or a chalk line, and in the holes for screws or dowels to make a bold mark.
The toilet temporarily remove to the side, with the help of a diamond drill on the marks, the holes under fastening are made. At this stage of the installation it is very important to keep the fragile tile. Therefore, the drilling is carried out by a drill in the mode of unstressed drilling. Only passing the layer of glaze can be used a shock function, providing minimal pressure on the drill.
If there were no dowels with the toilet with the toilet, they can be purchased at any store of plumbing products. You will need two long metal screws, two plastic dowels, two washers and decorative caps to hide screw heads. All this is sold together as a "set of toilet bowl". First, plastic dowels are inserted into the holes, then the toilet is installed in such a way that the holes for the attachment are exactly above the dowels. A gasket is installed under the filling and, in addition, the joint of the spot with ceramic tiles is additionally filled with silicone. This measure will ensure the sealance of the seam and protect the fastening screws from rust.
A sufficiently responsible moment consists in direct mounting to the floor. Screws with washers are inserted into the holes and tightly twisted, but not so much so that the enamel of the device is cracking or chips were formed.
When the toilet is already in place, it remains to be connected from the sewage. The corrugated pipe connects the release with the fitting of the sewer tube, the connection site is labeled with silicone.
The flush tank is attached to the upper part of the toilet with stainless steel bolts and sealing gaskets.
Water to the tank is served through flexible hoses. When spinning nuts on the hoses, it is important not to drag, this work is done manually, only then you can slightly tighten the nuts with the key.
In order for silicone to finally dry and the toilet, is ready for use for three hours enough.

On this installation on the tile is finished.

Installation of toilet bowl on epoxy resin

Above the classic installation scheme with their own hands. In addition to it, there are techniques such as an attachment on an epoxy resin or on a wooden board with screws.

Installing the toilet to the epoxy resin requires special flooring. They are applied notches and artificial roughness are made, the surface is treated with solvents or other degreasing materials, a resin is applied with a layer of at least 0.5 cm. The device is attached to the place and fixed in the desired position using various devices by 12 hours. Only after this time is possible to continue work.

Making repairs in the bathroom or toilet, it is very important to choose correctly and install plumbing. If the owners perform repair and finishing work on their own, then the installation of the toilet is one of the most important tasks for them. Prepare for this process and learn everything about the installation and dismantling of various types of plumbing, you need in advance. Careful preparation will allow saving time and strength that will necessarily need at various stages of repair.

Selection of sanitary ware

Assembly and installation of the toilet - responsible work, requiring some skills and patience from a person who will mount the design. But even before the installation itself, it is necessary to decide on the choice of plumbing. Modern manufacturers offer consumers with different types of plumbing structures that differ not only in appearance, but also in their functionality.

In the store you can find models having different shaped bowls (as they look, you can see in the photo):

visors;
funnel-shaped;
plateless.

The types of drain eyeliner of plumbing structures are also distinguished. They are:

horizontal;
vertical;
located at an angle of 45 degrees.

Also, the hosts can choose a plumber having different mounting methods:

traditional (drain tanks are attached to the stool or to the wall, there are also models with combined tanks);
with installation (the tanks are mounted in the wall, only a drain button is seen, the stoolchak itself can be suspended against the wall).

When choosing plumbing in the store, you need to take into account the area and configuration of your toilet. The shape of the bowl may be any, but from what will be the drain eyeliner and the type of installation (with or without installation), the amount of preparatory and repair work depends on the owner of the apartment.

Demonstration rules

Installing a new toilet - an important thing, but before performing this work, it is necessary to dismantle the old Sanfayans design located in the toilet. Experts recommend dismantling with the following rules:

before starting work in the apartment you need to turn off the cold water (you also need to not forget to drain the water accumulated in the drain tank);
when the water supply is discontinued, it is necessary to gently disconnect the pipes supplying water into the tank;
after disconnecting the pipes, it should be proceeding with the removal of the tank itself, unscrewing the fastening bolts (it is necessary to do it carefully, so as not to drop and not break the Sanfayns design);
the next step should be revealing the bolts on which the stools itself is mounted to the floor (if the bolts are closed and not unscrewed, they can be poured by kerosene or special lubricant fluid sold in stores with building materials, and leave to dump for some time);
after the bolts are unscrewed, it is necessary to disconnect the drain pipe from the sewerage (if the drain pipe is reinforced with cement, it is necessary to gently knock on it to knock off the remnants of the building material);
if the owners do not plan to set their old stools in the toilet again, they can simplify the process of removal, for this they can simply smash the Sanfayans design of a sledgehammer and bring fragments to the trash in parts;
the removed design must be tilted several times in different directions to drain the remnants of water from the knee;
when the dismantling is completed, the hole of the sewer pipe must be closed with a dense cap for a while (the plug must stand until the installation of the toilet to the tile or other sexual coating starts).

Required tools

Before proceeding to such a process, like installation of the toilet with your own hands, you need to prepare tools and materials that may be required during the work. While working with plumbing, the owner will need:

perforator;
adjustable keys;
line or roulette;
marker;
thin hoses;
corrugation;
fasteners;
tape FUM;
rubber gaskets;
silicone sealant;
level, etc.

All of the above items, as well as everything else that is needed to be installed, can always be purchased in the store with construction materials. Like many other assortment, tools and fasteners, will be found in the departments with plumbing.

Preparation for work

So that the installation of the toilet, which is performed independently, has passed successfully, after dismantling it is necessary to take care of pipes and sex coverage in the toilet. Before making a plumber, the owner should pay attention to the floor:

if there is a smooth tile on the floor, and its replacement is not planned, the floor can be left alone and immediately go to the inspection of pipes;
if the tile in the toilet is lined unevenly, but the owners do not want to change it, it is necessary to tighten into the floor of the Cooks, to put them in terms of the level and to fix the sanitary design (if you leave the floor uneven, plumbing will be crooked and will not be dumbered);
if the toilet is planned to be fully replaced the sexual coating, it is necessary to remove the old tile or linoleum, pour a smooth tile of concrete, and after it is frozen, it is gently putting a tile.

Installing the toilet to the wooden floor (including the installation of the toilet in the private house) must be performed on the same principle. The sexual coating can be perfectly smooth if possible, otherwise you will also have to score chips. If it is planned to install the built-in toilet (suspended), then the flooring can be changed after editing.

After the floor is prepared, the condition of the pipes should be estimated. Old cast iron sewer pipes are best to change on light plastic structures (when necessary, sewer can be cleaned). Water supplied pipes can also be replaced by new (for example, copper) and put a crane on them, with which at any time it will be possible to overlap the water supply.

Montaja rules

Often complete with plumbing is a detailed installation scheme. The owner must examine her to understand how to properly assemble and install the plumbing design. There are certain rules for installing outdoor plumbers in the toilet that should be followed in order to obtain the expected result:

first of all, it is necessary to put the design to the floor (to the place where it will be fixed), to circle its leg and mark the attachment points;
plumbing design must be removed to the side and drill holes in the marked attachment points, the dowels must be screwed into the finished holes;
then the plumbing needs to put in its place, insert seals and fasteners and tighten the bolts in the holes and gently tighten the bolts (tightening fasteners, it is necessary to ensure that you should not damage the foot of the plumbing design and do not thread the thread);
in some cases, the plumbing feet have no holes for fastening, in such situations the plumbing design is attached without bolts for sealant (for silicone);
when plumbing is securely fixed, it is necessary to make sure that it is perfectly smoothly, for this you can use a special construction level (level adjustment does not take much time, but will allow you to see and quickly correct possible errors);
if everything is done correctly, and plumbing is exactly exactly, it is necessary to put on the masking plugs onto the fastener, and to attach the seat and the lid on the stoolcake, which always come in a set with plumbing (installation of the seat and the cover of the toilet will not take much time, how to perform such work, you can see In the instructions for the plumbing design).
installation of the angular toilet may be slightly complicated than the installation of the usual plumbing structure, but in general this process passes through the same rules as the mounting of the direct model.

After the correct installation of the bowl of the toilet will be completed, you need to go to the sewage connection. You can connect the horizontal or angular plums with the sewer pipe directly by scraping them with a sealing cuff. If this action is made for some reason it is impossible, then you will need to install corrugations on the toilet. All connections should be woven with a sealant, which securely creates the design. Installing the toilet with direct release into the wall, as well as the installation of the toilet with the oblique release, with their own hands, does not deliver special problems, almost any man can cope with this task.

If the vertical plums goes to the floor, then the connection to the sewage will need to be carried out before attaching the bowl of the plumbing design. It is necessary to install a screw flange into the drain hole, and insert a drain pipe into it. Due to the special locking ring, the sewer tube and the drain will be securely interconnected. After that, you can mount and fix the floor toilet itself.

The next stage of the work is to install a tank for launching water to the toilet. Typically, a drain mechanism located in a tank is sold in the already assembled form. If parts of the reinforcement are disassembled, they will have to be assembled, following the instructions attached to the plumbing. When the entire design is ready to connect, it is necessary to put a special gasket into the water hole, carefully put the drain tank and connect both parts by bolts.

When the installation of a separate drain tank on the toilet will be completed, you need to connect the water supply. To do this, you need to take a flexible hose and connect the tap tube with a tank with it. To check whether there are no leaks, you need to open the valve of the pipe supplying water, to fill the installed drain tank to the maximum, and then lower it (you can repeat this procedure 3-4 times). If with one or on the other side the hose leaks, it is necessary to pull the bolts.

This is where the installation of an outdoor toilet with a compact tank is passed. Installation of the suspended toilet with installation is carried out differently. The owner who decided to spend all the repair work independently, you need to know how to correctly perform the installation of such structures.

Installation of suspended structures and installations

Installation is called a design needed to hide the pipes and a drain tank. The stoolchat can be mounted in the usual way, and the installation of a hidden toilet bowl is carried out in bulk the wall on which you can only see the buttons to start the drain. Similar structures look very stylish and modern, but not always suitable for small-sized toilets, because Creates a useful area of \u200b\u200bthe room.

Installing the installation of the toilet with your own hands (the video of this process can be found on the Internet) is carried out as follows:

it is necessary to build a metal frame with frames to which the built-in drain tank will be fastened (the finished design should have a width more than the tank width);
the next step should be the installation of a separate drain toilet tank, which must be attached to the frame (the drain button must be placed at a distance of about one meter from the floor);
the finished installation must be attached to the floor and walls using durable screws (at this stage it is necessary to use the level to install the frame exactly, and not at an angle);
after the design is fixed, you need to connect the water supply to the tank, and then remove the sewer pipe to the drain (for this you can take a corrugated cuff);
when all the basic works are completed, it is necessary to build a metal-powered framework, in the center of which will be placed, and to strip it with plasterboard;
the last other step will be the installation of the toilet to the tiled floor or other sexual coating;
after installation of the suspension toilet, the plasterboard surface is finished with tiles or wallpapers.

The installation of the suspended toilet is carried out with their own hands on the same principle. The owner of the apartment needs to build the same design as for the built-in tank, and hang the bowl on the pre-installed pins. The height of the installation of such a toilet should reach approximately 42-45 centimeters from the floor (most often the distance to the outboard toilet from the floor is calculated individually).

Installing the system of frame installation for the toilet with your own hands is one of the most complex tasks during repairs. The installation of mounted plumbing structures and the built-in tank can only be a person who has at least minimal experience in plumbing and repairs. It is much easier to purchase plumbing equipment with a finished installation system and assemble it by the attached scheme. For example, the installation of the installation of the Grohe toilet bowl does not deliver special hassle and will look very attractive.

Professional help

If an independent installation of mounted toilet, installations under the toilet or conventional outdoor plumbing design presents complexity for hosts, they can always ask for help from professional plumbers. Experts who have all the necessary tools for installing the toilet can be qualitative and quickly fulfill all the work.

People who have decided to trust professionals are always interested in how much the installation of the toilet is. The price for work usually depends on the type of mounted design:

installing conventional toilet bowls with a separate tank, directly attached to the bowl, will be from 1 to 2 thousand rubles and higher;
installing the installation frame for toilet to the toilet will cost from 2-2.5 thousand rubles and higher (how much accurate installation is worth installing, it always depends on the complexity of the design);
the installation of wallile toilet will cost 1.5-2 thousand rubles and higher;
the cost of dismantling plumbing will vary from 400 to 700 rubles.

The cost of certain works may also differ in different plumbing firms. Customers are best known in advance how to install a floor or suspension toilet, and what the price of this service will be.

In custody

Dismantling and installation of the toilet - a responsible thing, which may seem like an ordinary person very difficult. In some cases, it is better to trust such work by a specialist who will take into account all the wishes of the client and will install in a short time.