Imitation burning firewood with their own hands. Artificial fire for the fireplace with their own hands

Many love to look at the fire. At the same time, not every person can afford to have a real fireplace in the house with a real flame in the focus. But today, due to the presence of such material as plasterboard, you can make a decorative fireplace with your own hands.

But when all installation work is completed, the question arises how you can create a simulation of real fire in an unrealistic fireplace. This article will tell you how to make it yourself in various ways.

The decorative fireplace made of plasterboard requires compliance with fire safety standards, since this design is not designed for a real fire. In addition, the apartment has no possibility of assembling a real fireplace.
But the fireplace, even if it is decorative, requires imitation of real fire. You can make it with your own hands in several options. The following imitation is used in this situation:

ferry;
the creation of "theatrical fire";
use of saline lamps;
imitation of fire with the help of Christmas garland;
installation in the center of the TV;
using candles.

Consider in more detail each of these options.

Couple instead of fire

Imitation ferrom

The most difficult way to simulate fire in a decorative fireplace is your own hands. Not every person will be able to make such a simulation, as a specific set of components and equipment is needed here, as well as electrician skills.

To create a fire of this kind, you will need the following components:

special DMX controller;
fan with a diameter of 90 mm;
LED RGB lamp;
Dmx decoder;
three pieces of ultrasound generators for fog.

These components can be selected by the parameters of the available fireplace, as well as the manufacturer and characteristics. It all depends on which end result you want to get.
All these components are included in the equipment for steam electrocamines, as well as concert devices for creating a steam effect.
With properly connected components, you can create imitation by the type of cold glow, which allows you to create indistinguishable
from the real game of fire. If you plan to use this type of fire imitation, it is important to provide the necessary parameters of the equipment and mount the focus of the desired size.
The principle of operation of this installation is as follows:

on the bottom of the container, in which water will be nanite, put the collected fog generator;
this generator is equipped with a membrane vibrating with a certain ultrasonic frequency, thus creating a reduced pressure. As a result, almost vacuum is obtained;
due to this, water evaporates at room temperature;
next, cold pairs, with the help of a fan, the top rises;
at the top it is highlighted by the LED installed - lamp;
above all this design we put a diaphragm;

Note! Near the diaphragm works Bernoulli law. According to it, the speed of movement of air near the hole is higher than the smaller diameter of the hole. Therefore, the imitation of the flame acquires a more realistic appearance. You can try different diaphragms to get the most desired imitation result.

Assembly of such equipment can be carried out according to this scheme.

Scheme

The correct assembly of components will allow you to make your own hands in a decorative fireplace the most realistic imitation of fire.

"Theatrical" option

As can be seen from the name, such an imitation is most often used in various theatrical productions. But it is also good and in order to make a flame imitation in a false fireplace.

"Theatrical" imitation

To make a similar imitation to do it, you will need the following components:

light White Silk Laces;
three halogen lamps having reflectors;
quiet and large fan;
three color filters. It is necessary to take red, orange and blue filters;
box or special bowl for assembling simulation design.

When all the necessary components are available, proceed to the assembly of the false fire according to the following scheme:

install on the bottom of the box / bowl fan;
cord from it we take out out;
then the halogen lamps are dripped over it in one axis. They must give light up;
next, at a distance of 2 cm above the halogen lamps, we install light filters;

Note! Light filters Freaky as follows: In the middle of blue, and on the edges - orange and red. The placement of filters will thus give imitation of greater brightness and relief.

Installation of light filters

from the harvested loskutka we cut pieces of fabrics of different sizes. The best form is the triangles. They will give a flame of greater realism;
krepim slices of fabric to the box / cup along the edges of the fan.

When connecting the fan to the electrical network, an artificial fire will appear in the fireplace.
This method is easy to implement and allows you to create an almost real flame in the fireplace.

Salt lamp

The use of salt lamps in decorative fireplaces to create an artificial flame is considered the most useful and efficient way.

Salt lamp

The salt lamp is a special lamp, the plane of which is made from the untreated salt crystal. Inside such a ceiling is a standard light bulb. When connecting the lamp, the ceiling is heated and begins to emit negative ions into the air. They bind positive ions (proceed from household appliances), which negatively affect the human body, thereby contributing to the better well-being of all households.
By cons of such a method, it is worth attributed to a sufficiently high cost of salt lamps, and the advantages are ease of installation.
Using plaffers of different staining, it is possible to make artificial fire in the fireplace very easily. In addition, using several lamps at once of various sizes, you can create a fire imitation.

Christmas christmas garlands

Preparation of branches

All people love the new year. Therefore, every person in the house there is not one christmas garland. But few knows that with her help you can easily and quickly make artificial fire in a decorative fireplace. Therefore, this method is considered one of the easiest and most effective. Moreover, any person will cope with him, and in terms of cost it will be very cheap.
So that the flames seem to be present, you will need the following materials:

branches of trees of various sizes;
aluminium foil;
lace. It is quite possible to cut off the old dress;
stones (several pieces);
glue;
christmas garland having a color background in red, orange or yellow. The best solution will use a shimmering garland.

The assembly of the simulation structure occurs as follows:

wind the foil branch without skips;
fracture lace glue and fastened to the branches. Next, we wait until they are completely dry;

Note! Up to complete drying, it will take about a day.

next, it should be carefully cutting the case of lace and get billets from them;
after that, in a focus of stones, lay the stones in the circle;
in the middle of the received circle, put the garland, and the cord with the fork we take out out;
the resulting "lace" firewood put on the fire manner.

Stages Formation of a fire

Turn on the garland into the outlet and enjoy the imitation of the fire!
As you can see, this method is very simple to implement and will cost you a much smaller amount than all other ways.

Fireplace

TV in the fireplace

Another simple methods for implementing artificial fire in the fireplace is the use of a flat liquid crystal TV. But this method will be very expensive, since such an equipment is not cheap.
There are special TVs designed to embed into decorative fireplaces. They have a record with fire, which is reproduced in the fireplace center.

Sometimes the TV can be supplemented with a special optical system that consists of light filters. With its help, the image of the flame will become more expressive and volumetric.
In addition to this optical system, you can use the mirror system. They are located in the corners of the hearth, thereby making the image more volumetric.
In rare cases, you can take advantage of holographic installations. But this is a very profitable way.

Candles and romance

The easiest, but also at the same time the most dangerous, method of creating an illusion of fire in a decorative fireplace is the use of ordinary candles.

Candles in the fireplace

But here it should be remembered that it is necessary to cover the fireplace with plasterboard sheets with fire-resistant properties. This will minimize the risk of fire.
Among other things, the candles will smoke, which makes this way less popular than all of the above.
This method is considered one of the design solutions to give the room of romanticity and fabulousness. In this situation, the candles can be placed both individually around the perimeter of the hearth, and to install on low candelabr.
As you can see, the imitation of the flame in a decorative fireplace is possible with their own hands. You will only have to choose the most suitable option for yourself, to implement it correctly (if it is complicated in performance) and enjoy the decorative fireplace even in the apartment.

What is a fire imitation is the creation of an artificial flame in Falish fireplace. Many residents of apartments dream of making a fireplace, fascinating a picture of fireMany people like to observe the flames. At the same time, not everyone can accommodate the houses a real hearth with real fire and firewood. Nowadays there is a way out, make a false fireplace is quite real independently, it is enough to cook: drywall (GCL), a tool, good mood. However, when the montage of the frame is completed, the question arises on how to simulate the real flame in the fake fireplace.

Imitation of fire in the fireplace: design options

Decorative homemade foci, made of GCC, require compliance with fire safety standards, as such a design is calculated exclusively on an artificial fire.

There are several ways to create artificial imitation of fire

Most often masters apply the following types of fire imitation:

Using steam.
Creation of "theatrical fire."
Application of salt lamps.
Installation in the center of the TV.

The most difficult way to create a decorative flame - ferry. Not everyone may create such imitation, because here it takes a specific set of components and special equipment, as well as the skills of working with electronics.

To make the fire of this kind, it is necessary to prepare:

DMX controller.
Fan with a diameter of 9 cm.
LED RGB lamp.
Dmx decoder.
3 ultrasound generators for fog.

These devices need to be selected by the parameters of the built fireplace, under the layout, as well as the manufacturer and characteristics. It all depends on which source result wants to get a master. All these devices are part of steam electric fireplaces, as well as concert electrical appliances that create a steam effect.

With the right connection of devices, it is possible to imitate on the cold glow system, which makes it possible to make a fire imitator, which is difficult to distinguish from the real hearth.

If the wizard wants to use this method of imitation of the flame, it is important to provide the necessary parameters of the components, and mount the center of the desired size.

The principle of operation of such an electrocamine looks like:

At the bottom of the container, in which the water is pre-flooded, it is necessary to put the fog generator.
The generator has a membrane that creates vibrations with a certain ultrasonic frequency, providing reduced pressure. Therefore, it turns out, you can say, vacuum and water evaporates at room temperature.
Thanks to this couple rises up.
From above, the LED lamp lights occurs.
A diaphragm is satisfied with the design.

Assembling on technology will give the opportunity to create yourself in a false fireplace more natural imitation of the flame. The second method is the theatrical option. As already understandable, this method is used in theatrical circles, for all sorts of productions. However, it is also suitable in order to make a lingerie, imitation of fire.

To independently make such imitation, it is necessary to prepare the following items:

Loskut with silk and white silk matter.
3 halogen lamps with reflectors.
Silent, powerful fan.
3 filters: red, orange and blue.
Control or special bowl for assembling false design.

When everything is prepared, you can start an assembly according to the following scheme. On the bottom of the box, the bowls need to arrange a fan. The cord should be removed out. Next, one axis must be fixed with halogen lamps, so that the light is pointing up. Then, at a distance of 20 mm above the lamps, you need to arrange light filters.

From the prepared matter you need to cut the patchwork of various sizes, better triangular shapes, as they will be more realistic.

The next step must be fixed the flap to the box, the cup along the edges of the fan. When the fan is turned on, it will not be real, but very similar with the natural fire in the fireplace. This method is simple enough and makes it possible to make an almost present fascinating flame in the fireplace.

Artificial fire for the fireplace: Salt lamp

Application in artificial fireplaces of salt lamps to recreate a decorative flame brings benefits and is considered an effective way. Salt lamp is a special light reproduction, which is made of an intact salt crystal. In the inside of such a plafone there is a conventional light bulb.

Use in decorative fireplaces of salt lamps to create an artificial flame is considered the most useful and effective way.

When the lamp is connected, the ceiling begins to warm and exhibit negative ions into the air.

They bind positive ions (from household appliances), which adversely affect human health, thereby contributing to improving the well-being of residents at home. The disadvantages of this method should include a fairly large price of saline lamps, and to the pros: realistic, aesthetics and ease of installation.

Applying the plaffones of various colors, it is possible effectively and very simple, to independently do in the fireplace is not natural flame. In addition, by applying several lamps at once everybody, it may be possible to make a fire imitation.

Firewall do it yourself: tv instead of the fireplace

Another not a complicated way of selling no natural flame in the fireplace is the use of a flat LCD TV. But this method is considered the most costly, since such an equipment is expensive. Developed special LCD TV, which are manufactured specifically for artificial fireplaces.

You need to choose a TV for false fireplace so that the screen fit inside the fireplace. After that, find a video with the effect of flame burning and record on the TV, for this it must be USB

They have a video from:

Playing flames;
With smoldering coals;
With a bright fire.

This entry goes in the focus of a false fireplace. Sometimes TV is possible to supplement special optics, which consists of light filters. Using it, the image of the fire will be the most expressive and volumetric. In addition to this optics, it is possible to apply a mirror system. They are located along the corners of the fireplace, and the picture is more realistic, such a backlight looks very beautiful. In rare cases, the holographic installations may also be applied. But it is not fairly profitable.

Decorative firewood firewood

In specialized salons you can find an abundance of variants of similar products, there are quite realistic firewood on sale, having a natural lamp pattern. They can be plastic or ceramic. Any imitation, purchased or made independently, is intended to impart realism with a decorative fireplace to help feel all the magnificence: home comfort, harmony, calm and warmth.

Fireplaces set more and more to heat the room, and to create a coziness atmosphere. In this case, decorative firewood will be relevant acquisition

Imitation of plastic wood or coal, has a rather complicated principle of operation.

Coal and firewood are illuminated with red backlight. The light can be located inside the firewood. Of course, this is not so reliably, but still. For more expensive electrocamines, characteristic of flickering or artificial transmission of fantastic flames. It is possible due to a special mechanism in which special elements rotate around the lamp, alternating with transparent and shaded zones. Such a backlight may be located or for a milying of the lane, or in the inside.

The exact same illumination system may be applied to achieve the effect of fire, using natural coal, which must be placed in a niche of a false fireplace. In this case, the backlight must be placed from the bottom.

The plausible imitation of fire in the fireplace do it yourself (video)

So, in the apartment room there is no possibility of a device of the real fireplace. However, the fireplace, even if it is artificial, requires imitation of a realistic flame. This is independently possible in several ways described above.

Examples of the fireplace of the fireplace (photos of ideas)

Imitation of flames

To create an artificial fire in the fireplace with your own hands, you can take advantage of someone's experience, rich in original ideas:

the basis of the design of the TV screen becomes;
the fire is imitated due to the three-dimensional image;
the illusion of burning is created;
cold fire and fan;
fiery effect from the steam generator;
real lamps with special backlight.

LCD screen, as the basis of the structure

Falsh fireplace in modern interior

This method is considered the most affordable. Decorate the house of the fiery hologram will not be a lot of work. The picture in the 3D format is placed in a decorative fireplace so that its edges are invisible. Optical illusion arises due to the LED backlight scheme.

Made artificial firewood for the fireplace with their own hands will serve as an excellent addition to the scenery.

Decoration of fire with hologram

Create illusion of fire

To implement the idea, we need mirrors, they are placed in the fireplace and give the illusion of space. Corners between glasses should be different. LED lamps are additionally used to design a virtual flame. The model works as follows: The fire of the electrocamine is reflected from the mirror surface. Due to the fact that the mirrors distort the image, the effect of volume is achieved, the sparks seem to fly, and the flames are moving in all directions. I want to admire such a spectacle for a long time, because the fire is very similar to the sparkling fire.

Cold Fire

It is easiest to create a decorative fire for the fireplace with the help of an ordinary fan and flavors of red fabric. The process will not take much time. Triangular fabric loskuts are glued along the edges of the cardboard box. LED lamps, blue, red and yellow, on the sides of small mirrors and optical filters are attached in the corners. The fan is installed so that the air flows are moving up.

At the end stage, the product is placed in the fireplace and connects to the power grid.

Fire created using steam generator

Complex structures look the most believable. Thanks to a water vapor generator, a stunningly beautiful hearth with an artificial flame is obtained. Here you will need patience and several components immediately:

small fan;
ultrasonic fog generators, 3 pieces;
water packaging;
distilled water;
lED lamp, but suitable simple;
cardboard box.

Imitation of fire in the fireplace with a water vapor

Fog generators are stacked on the bottom of the box. On the side of the side the ventilating device is attached. Water is poured into the tank and is installed on top of ultrasonic devices. The lamp is fixed above the fan. Construction connects to the network.

Artificial fire extracted using a generator is quite realistic.

Natural Length Backlit

Like decorative firewood for a fireplace with highlighting of the LED tape, you can use real lanes. For this, the LEDs of yellow, red and white colors will be suitable. The lamps are beautifully laid on the shelf inside the focus, fasten each other, then chaotically wrapped with a LED ribbon. Flickering lights and natural wood complement the interior, look stylish and original.

Artificial firewood

If electrocamine is installed in the house, then it is better to choose special heat-resistant firewood. Artificial lamps for the fireplace are made of ceramics. They are safe and durable. LED backlight here is also relevant.

Artificial fire and decorative firewood for fireplace with their own hands

Artificial fire and decorative firewood for a fireplace with backlit with their own hands. Types and options for mounting backlight

Imitation of fire in the fireplace: options for false fireplace do it yourself

Initially, the fireplace in the house performed an exceptionally heating function and only after that the role of interior decoration. Today, a central heating system is used as the main source of heating in an apartment or house. That is why many began to give preference not to a classic solid fuel furnace, but more modern variation called a false fireplace. Such models can be bought or make your own hands from the remedies, as they carry exclusively decorative function.

The fireplace, the imitation of which takes place, can be collected and designed by the hands of an experienced professional who can recreate the necessary image, according to all the wishes and preferences of the customer. Imitation of fire in the focus of such a portal can be done in various ways, the present flame in this case is almost never used.

Main varieties

Before installing an artificial fireplace in a house or apartment, first of all it is recommended to familiarize yourself with the main variations and variations that you can create both your own hands and meet. in specialized stores:

Imitation of fire in the fireplace can be prepared and reproduced without fire-hazardous sources, eco-friendly and durable materials. You can assemble your own hands at home portal from plasterboard or foam. Such materials are distinguished by affordable cost and ease of use. To work with them, it does not need an expensive and professional tool. The finished product will have a small weight, which is extremely important, especially when installed in the apartment or on the second floor of a private house. Such a false fireplace due to its small mass should not be decorated and decorated with heavy objects and purchased fireboxes. Hypzarton is distinguished by the heat resistance, which in turn allows you to decorate its focus and shelves with candles. The fireplace with candles looks very exquisitely and charming;
Fireplace, apartment with whom will look original - can be collected from plywood. The portal for the fireplace from plywood is characterized by budgetary. However, it is not very stable and reliable. The fireplace from plywood requires high-quality surface protection, since the material quickly absorbs moisture, swells and deformed. The benefits include environmental friendliness and naturalness of the material;
Fireplace, stone or brick for which they perform the role of the basis will be more reliable and most refractory. Such materials are well withstanding high temperatures, their sharp differences are distinguished by durability and durability. For particularly large and bulky fireplace portals, it may be necessary to build the foundation. The price of a brick fireplace is high enough, and the construction cost time. However, in such a portal, if desired, electrocamine can be installed. Since the cost of natural stone is high enough, the portal cladding can be performed by artificial minerals.

Creating a focus

The fireplace milying may be the most diverse. First of all, everything depends on your wishes and preferences. If you want the focus to perform the heating function, initially pay attention to the electrocamens for home and apartments. Buy an inexpensive fireplace can also be in our online store.

Decorative fireplace can be treated with garland. Such a garland is stacked both in the hearth, and can be located on its perimeter, or in chaotic order. It is recommended to select garlands with traditional classic flames of burning lamps. To give the imitation of the burning fire in the fire, you can add ceramic lamps to the hearth.

To add a false fireplace, you can with the help of branches of trees. You can arrange them in any way. As an option: Wrap a foil and lace branches, then fasten various stones, seashells and other decor to glue. You will have lace branches at the output, which can be placed both completely separate and in vases.

Lace can be both over the length of the entire branch and only on a certain area, the interval. After gluing, it is necessary to give a product to dry completely and only after that, use the decor for the design of false fireplace. If desired, such branches can also be colored or supplemented with glitter. Alternatively, put them in the fireplace focus and highlight the LED garland.

Also for decor you can use candles. They can be located apart or located in various openwork candlesticks, candelabras. Install them inside the focus or can also be supplemented with a fireplace shelf. Do not place candles in a stone, beige, cream shade, as during the operation of the decor, on the surface of the portal and in the focus there will be ugly black traces and prints from the candle.

Imitation of fire in the fireplace can be performed in one very interesting way. At the exit you will get a fireplace with candles. To do this, find 2-3 beautiful laminates of the right form and cut out in each of them 2-3 holes. In the resulting holes, lower one candle. It is important that the candles are in the candlesticks or in special protective frames. It will not allow the lanes to light up in the process of burning candles.

As a more expensive option, you can decorate the fireplace focus with a saline lamp. Such a device will look stylish and effectively. The disadvantages include a fairly high cost. The main advantages are the use of health salts, creating a cozy atmosphere in a house or apartment.

Fireplace electric can also perform an extremely decorative function. It can be equipped with a steam generator and even an air humidifier!

Modern technology and fresh solutions

Electrocamine Live Fire is the most realistic flame imitation means. In this case, the imitation is made using modern technologies, namely the LCD screen with a voluminous and high-quality picture and animation.

Make any flame more voluminous and spectacular, can be installed on the contrary and on the sides of the focus, under a slight slope of several large mirrors. The fireplace with a mirror will create the illusion that the fire is real. Install mirrors can also be in the midst.

If you like to create a variety of things with your own hands and want to get the best result, we recommend to build a simulation of flights. To do this, we need decorative firewood, LED garland or lamp, fabric, and a number of other girlfriends.

The basis of our firewood is a cardboard. Each canoe need to cut their cardboard and give the volume, glue. The surface can be painted with acrylic, gouache or watercolor to choose from, after which it is to dry firewood. Firewood glued in the shape of a well and stacked in the hearth. If desired, such cardboard lamps can be replaced by real. In this case, construction glue is used for gluing.

To create volume and characteristic shades, you need to buy a LED lamp in advance, which will flicker various shades. It is recommended to give preference to the characteristic color spectrum - yellow, red, orange. A translucent white fabric is used as a ceiling, and the framework is constructed from four durable wires, the length of which will be 150-300 millimeters.

The light bulb is fixed inside the focus, right above the imitation. The wire frame is installed in the center of the well and is complemented by a translucent cloth. When turned on, a fairly realistic effect of burning flame will be created.

Realistic imitation

One of the most realistic options for creating imitation is the so-called box with fire. To create such an effect it is necessary to buy LED lamps, preferably red, yellow and blue shade. As a reflecting surface, you can choose a small mirror, foil. Also, for this effect, the fabric or scraps (silk) will be required. The so-called fire will be placed in the box.

At the first stage, we produce decoration of the very foundation (box), after which we act according to the following step by step management:

We put in the box fan;
LED light bulbs are located and fixed near each other;
Space near the fan is complemented by flap.

Such a box with fire is placed inside the fireplace portal and allows you to reproduce a rather realistic effect.

You can also perform imitation using aquarium. To speak more detail, you will need to prepare aquarium of this size so that it can be installed in the focus. After that, inside the aquarium is placed and the garland with LEDs is fixed, the container is filled with water. When the garland is turned on, the effect of blasting water will be created, which looks very original.

The internal space of the aquarium can be decorated with seashells, stones, algae and other elements at your discretion.

The category of the most realistic and complex in the embodiment of variations includes the creation of the illusion of the flame burning in the focus using steam. To develop a couple, you will need to buy 2-3 devices generating fog (ultrasound).

It will also be necessary to prepare a fan, the tank in which water will be poured, the framework for the placement of imitation and the RGB lamps.

Devices that generate fog are installed in the inside of the box together with the fan, then place the lamps, and install the prepared reservoir for flooding water to the generators. Such an effect is very realistic, but at the same time his recreation costs quite expensive.

The fireplace in the interior of your apartment for home will be a real homeie and fill the living room, the bedroom comfort. The outdoor fireplace can be both confrient and island, angular, depending on your wishes and preferences. False the hearth is fairly simple in the installation, it has small dimensions and optimal weight, and some models can rearranged from place to place. To simulate the flame you will need mainly inexpensive workflows, and the design itself does not require the erection of an additional foundation and the smoke.

Such a home focus will allow you to arrange cozy family evenings in the company of friends and close to a cup of warm tea.

Imitation of fire in the fireplace: options for false fireplace do it yourself

Imitation of fire in the fireplace: Options for false fireplace are original, the fireplace in the house performed an exceptionally heating function and only after that the role of interior decoration. Today at

Fireplace: Flame Imitation

As nice in the evening in the twilight will plunge into contemplation of the flame languages, feel a little bitter aroma of burning lane. But even the owners of private houses are far from always solving breaking the walls, rebuild the attic and roof for the installation of this fireplace. And this is only the first half of the case. During operation, it is necessary to harvest firewood, screamer, clean the chimney ... And all these efforts are directed mostly only to the creation of the atmosphere, because the heating of houses today is much more practical and less labor and material and material.

And the atmosphere of the house with the hearth is quite recreated the decorative false fireplace and imitation of the flame. In this article we will talk exactly about imitation, that is, about safe ways without an open big flame, unlike biocamines, which are also successfully used to decorate the premises, but have a real fire.

"Fireplace: imitation of the flame ferry

Fan 90 mm;
DMX controller VELLEMAN K8062;
DMX decoder Besten DMX Decoder 350;
LED RGB lamp MD-9P;
3 Chinese ultrasound fog generators

The diaphragm is installed on top. According to the law of Bernoulli, the speed of air movement near the hole increases the greater the smaller the hole in it, which makes the "flame" more realistic. You can try different diameters of the diaphragm to achieve maximum similarity.

"Theatrical" fire

So, we will need:

Large fan (preferably quiet)
Three halogen lamps with reflectors
Three color filters (orange, red and blue)
White light silk flap
Bowl or box for the founding device of our flame

At the bottom of the box or bowls install the fan, the cord is displayed out.

Above it on one axis, install halogen lamps so that they shine up. Over them at a distance of about 2 cm fix colored filters. Red and orange - along the edges, blue - above the middle lamp. Such a bar will give our flame greater relief and brightness.

From the flap of the fabric, cut pieces of different sizes. It is desirable that these were triangles of the wrong shape. So the flame will be more realistic.

Fix the flap in the bowl or box around the fan. All, our fire is ready!

Turn on the device into the outlet. Fabric flaps under the action of the fan instantly climb up and tremble, the backlight creates a similarity of yellow-orange flame. The glare lights run on the ceiling and walls, reminding the chopping of natural fire.

Candle fireplace

His pros is the simplicity of execution and the real fire, for which, unlike the wood focus, it is not necessary to harvest the fuel. Minus - Candle Candles.

Fireplace: Flame Imitation with Christmas Girls

Another rather common way to create fire imitation. Here I will tell you how to make a simulation of a wood focus.

Branches of suitable size
Lace (not new, cut with old clothes)
Aluminium foil
Several stones
Christmas electrolycard in yellow, orange or red gamma.

Thoroughly wrapped with lace glue and wind prepared branches in foil. We leave until complete drying (about a day).

From the stones in the place of installation of the focus lay out the circle. We put in the middle of the garland, we leave the cord with a fork outside.

Imitation saline lamps

These are such simple ways to decorate your home, make it more comfortable and original.

Fireplace: Flame Imitation

In the fireplace imitation of the flame in several ways. Our advice will help you embody the dream of a home focus in reality.

How to skillfully make imitation of fire in a false fireplace

Options for registration

ferry;
the creation of "theatrical fire";
use of saline lamps;
installation in the center of the TV;
using candles.

Couple instead of fire

special DMX controller;
LED RGB lamp;
Dmx decoder;

at the top it is highlighted by the LED installed - lamp;

"Theatrical" option

quiet and large fan;

cord from it we take out out;

Note! Light filters Freaky as follows: In the middle of blue, and on the edges - orange and red. The placement of filters will thus give imitation of greater brightness and relief.

Salt lamp

By cons of such a method, it is worth attributed to a sufficiently high cost of salt lamps, and the advantages are ease of installation.

Christmas christmas garlands

aluminium foil;
stones (several pieces);
glue;

Fireplace

Candles and romance

The easiest, but also at the same time the most dangerous, method of creating an illusion of fire in a decorative fireplace is the use of ordinary candles.

How to skillfully make imitation of fire in a false fireplace

Options for decorative fireplace in terms of simulating natural fire. What options exist how they are implemented and what advantages they have. Everything

Imitation of fire in the fireplace do it yourself

Options for registration

But the fireplace, even if it is decorative, requires imitation of real fire. You can make it with your own hands in several options. The following imitation is used in this situation:

ferry;
the creation of "theatrical fire";
use of saline lamps;
imitation of fire with the help of Christmas garland;
installation in the center of the TV;
using candles.

Consider in more detail each of these options.

Couple instead of fire

The most difficult way to imitation of fire in a decorative fireplace is believed to be precisely this method. Not every person will be able to such imitation, since there is no specific set of components and equipment, as well as an electrician skills.

To create a fire of this kind, you will need the following components:

special DMX controller;
fan with a diameter of 90 mm;
LED RGB lamp;
Dmx decoder;
three pieces of ultrasound generators for fog.

These components can be selected by the parameters of the available fireplace, as well as the manufacturer and characteristics. It all depends on which end result you want to get.

All these components are included in the equipment for steam electrocamines, as well as concert devices for creating a steam effect.

With properly connected components, you can create imitation by the type of cold glow, which allows you to create indistinguishable

from the real game of fire. If you plan to use this type of fire imitation, it is important to provide the necessary parameters of the equipment and mount the focus of the desired size.

The principle of operation of this installation is as follows:

on the bottom of the container, in which water will be nanite, put the collected fog generator;
this generator is equipped with a membrane vibrating with a certain ultrasonic frequency, thus creating a reduced pressure. As a result, almost vacuum is obtained;
due to this, water evaporates at room temperature;
next, cold pairs, with the help of a fan, the top rises;
at the top it is highlighted by the LED installed - lamp;
above all this design we put a diaphragm;

Note! Near the diaphragm works Bernoulli law. According to it, the speed of movement of air near the hole is higher than the smaller diameter of the hole. Therefore, the imitation of the flame acquires a more realistic appearance. You can try different diaphragms to get the most desired imitation result.

Assembly of such equipment can be carried out according to this scheme.

The correct assembly of components will allow you to make your own hands in a decorative fireplace the most realistic imitation of fire.

"Theatrical" option

As can be seen from the name, such an imitation is most often used in various theatrical productions. But it is also good and in order to make a flame imitation in a false fireplace.

To make a similar imitation to do it, you will need the following components:

light White Silk Laces;
three halogen lamps having reflectors;
quiet and large fan;
three color filters. It is necessary to take red, orange and blue filters;
box or special bowl for assembling simulation design.

When all the necessary components are available, proceed to the assembly of the false fire according to the following scheme:

install on the bottom of the box / bowl fan;
cord from it we take out out;
then the halogen lamps are dripped over it in one axis. They must give light up;
next, at a distance of 2 cm above the halogen lamps, we install light filters;

Note! Light filters Freaky as follows: In the middle of blue, and on the edges - orange and red. The placement of filters will thus give imitation of greater brightness and relief.

from the harvested loskutka we cut pieces of fabrics of different sizes. The best form is the triangles. They will give a flame of greater realism;
krepim slices of fabric to the box / cup along the edges of the fan.

When connecting the fan to the electrical network, an artificial fire will appear in the fireplace.

This method is easy to implement and allows you to create an almost real flame in the fireplace.

Salt lamp

The use of salt lamps in decorative fireplaces to create an artificial flame is considered the most useful and efficient way.

By cons of such a method, it is worth attributed to a sufficiently high cost of salt lamps, and the advantages are ease of installation.

Using plaffers of different staining, it is possible to make artificial fire in the fireplace very easily. In addition, using several lamps at once of various sizes, you can create a fire imitation.

Christmas christmas garlands

So that the flames seem to be present, you will need the following materials:

branches of trees of various sizes;
aluminium foil;
lace. It is quite possible to cut off the old dress;
stones (several pieces);
glue;
christmas garland having a color background in red, orange or yellow. The best solution will use a shimmering garland.

The assembly of the simulation structure occurs as follows:

wind the foil branch without skips;
fracture lace glue and fastened to the branches. Next, we wait until they are completely dry;

Note! Up to complete drying, it will take about a day.

next, it should be carefully cutting the case of lace and get billets from them;
after that, in a focus of stones, lay the stones in the circle;
in the middle of the received circle, put the garland, and the cord with the fork we take out out;
the resulting "lace" firewood put on the fire manner.

Stages Formation of a fire

Turn on the garland into the outlet and enjoy the imitation of the fire!

As you can see, this method is very simple to implement and will cost you a much smaller amount than all other ways.

Fireplace

TV in the fireplace

Another simple methods for implementing artificial fire in the fireplace is the use of a flat liquid crystal TV. But this method will be very expensive, since such an equipment is not cheap.

There are special TVs designed to embed into decorative fireplaces. They have a record with fire, which is reproduced in the fireplace center.

Sometimes the TV can be supplemented with a special optical system that consists of light filters. With its help, the image of the flame will become more expressive and volumetric.

In addition to this optical system, you can use the mirror system. They are located in the corners of the hearth, thereby making the image more volumetric.

In rare cases, you can take advantage of holographic installations. But this is a very profitable way.

Candles and romance

The easiest, but also at the same time the most dangerous, method of creating an illusion of fire in a decorative fireplace is the use of ordinary candles.

But here it should be remembered that it is necessary to cover the fireplace with plasterboard sheets with fire-resistant properties. This will minimize the risk of fire.

Among other things, the candles will smoke, which makes this way less popular than all of the above.

This method is considered one of the design solutions to give the room of romanticity and fabulousness. In this situation, the candles can be placed both individually around the perimeter of the hearth, and to install on low candelabr.

As you can see, the imitation of the flame in a decorative fireplace is possible with their own hands. You will only have to choose the most suitable option for yourself, to implement it correctly (if it is complicated in performance) and enjoy the decorative fireplace even in the apartment.

Facing the fireplace furnace of plasterboard with their own hands is quite feasible. But should take into account a number of subtleties in the selection of material and work technology. If we talk about GLK, then it is universal. Moreover, not only levels surfaces, but also creates the perfect prefinite layer on which any finish can be applied.

Briefly about furnaces

Conditionally, they can be divided into two large groups:

Functional: open, closed. By material manufacturing steel or cast iron, brick. Such equipment requires additional refractory wall protection, gender.
Falekamines. Instead of real firebox, screens are used with imitation of flame flames. Chimneys are not installed for such devices, but electricity supply is required.

On the form of the portal (facade of the fireplace) there are no restrictions: rectangular, complex geometric shapes, radius, angular. For every taste and color. It should be noted that the finishing of the fireplace of plasterboard is your own hands is the process of preparing a rough base for finishing cladding.

There are two main types of fireplaces: these are functional - real, and falsecamines - imitation of the fireplace.

Design

This is the very first stage in which several important points should be taken into account, especially for functional furnaces:

It is necessary to determine the place of equipment in the room relative to the walls, the location of the furniture. At the same time, do not forget about fire safety: from flammable surfaces distance to the furnace - at least 700 mm.
The base for the equipment is recommended to perform from a concrete height from 300 mm. The perimeter of the foundation should go beyond the sizes of 250 - 300 mm on each side.
Recommended gap between the furnace and drywall 50 mm.
You should provide a box for aircraft.
Podium. The design should provide air flow for heating, withstand the weight of the furnace.
The thickness of the fireproof wall decoration and the technical gap of 100 mm between it and the furnace.
To accurately determine the dimensions of the portal, the parameters of the facing material should be taken into account: profiles: guide - 27 × 28 mm and rack - 27 × 60 mm). For the trim, it is recommended to use a refractory drywall refractory or moisture-resistant thickness of 12.5 mm.
The design of the portal and its finish should be organically fit into the interior.

The listed parameters will help to avoid mounted errors.

Preparation of the foundation

Considering that fireplaces - equipment fire hazardous, it should be provided for the preparation of gender and adjacent walls before weching the fireplace of refractory plasterboard.

Floor preparation

The fireplace for the fireplace has a significant mass. Plus is equipped with an increased fire danger. Therefore, at the first stage, a concrete base is prepared:

The layout of the portal on the floor is made.
Installing formwork.
The base is ground and poured concrete.
After the frozen, the podium lay out (4 rows of brickwork). Then installed metal corners under the furnace.
Put the final laying level.

The whole process is made strictly by level. The blockage of the foundation and the podium will cause problems with high-quality installation of the furnace.

Preparation of the Wall

The easiest option when the adjacent wall is posted from aerated concrete, foam concrete blocks or bricks. In this case, it is plastered and whiten. If the adjacent wall is posted from combustible materials (logs, bar, etc.), then the following works are produced:

The treatment of walls with flame retardant compositions.
Fastening on a metal profile of foil basalt plate. Requires ventilation gap between the wall and the facing plate. The sizes of the protective screen must be 500 to 600 mm exceed the dimensions of the future furnace.
The fastening of the drywall, which is putting on, and from above the clinker or porcelain tile is laid out.

Table top of plasterboard in the bathroom: how real is

Other options: asbestos stove, magnesite. If the equipment is installed in the angle, the walls of the walls are treated with a special refractory sealant.

The same thermal insulation is made under the chimney. It should be known that the gap from the refractory wall to the rear surface of the furnace should be at least 100 mm, from a fuel surface - at least 700 mm.

Installation of firebox, montage of frame

The finishing of the fireplace firebox is plasterboard is made directly at the installation site. Therefore, first install the equipment and only after that begin to mount the framework:

On mastic or special glue is installed plate of porcelain stoneware. It is time for frozen.
On the stove install the furnace. We should not forget about the technical gap between the wall and the equipment 100 mm.
It is placed on the basis and wall of the dimensions of the future design, a frame of guide and racking profiles is collected. All works are running strictly in terms of level. Fixing the frame to the wall and the floor is carried out using metal dowels. Profile bonds are performed using a press-washer.

As can be seen, the construction assembly for plasterboard should not cause difficulties.

When designing the fireplace, it must be borne in mind that this equipment is flammable and use a refractory fireplace.

Facing plasterboard

Optionally buy refractory plates, moisture-proof material can be applied. Cutting plasterboard parts is performed using a simple painting knife. According to the laid line, the cut is made to any direct bar, after which the canvas bend. Cardboard on the other side is cut.

When performing a functional fireplace, the firebox and a box for removing smoke must be installed thermal insulation and a foil reflector inside the device.

Facing the fireplace furnace of plasterboard with their own hands can cause difficulties in hard-to-reach places. And so the technology of assembly does not differ from any other design of GLC:

Sheets are sewn to profiles using metal screws. Hats deepen in the canvas. It is better if individual parts are cut from a solid sheet. This will greatly facilitate its prefinite finish. For the processing of angular joints of the structure, a special plasterboard plasterboard or a paint knife is used.
For thermal insulation on the inside, the trim is performed using basalt stove and foil. There is a foil minister. But attention should be paid to the quality of glue used in this material. It must respond to safety standards and withstand the long-term effects of elevated temperatures.

The smoke removal box can also be made of drywall. Thermal insulation and foil reflector inside the device should be installed. In the chimney box, there are holes for ventilation grilles.

Finish finish

For the final cladding, the plasterboard base is prepared as follows:

Close up with a putty hats from the screws. The composition should be selected for an aggressive medium with elevated temperatures.
After the frozen of the surplus is removed with a spatula or special painting skurt / sandpaper.
At the end, the surface is completely spacked, it is squeezed, it is ground. The finishing of the chipper furnace carcarter approached the finishing facing.

GLK is a universal material, therefore, porcelain stoneware, plaster, clinker tiles, natural stone and other can be used as an finishing coating. The finish finish under the style of the interior is selected.

An interesting decision is porcelain stoneware. The modern market offers this tile with imitation for any other finishing material - marble, granite, wood. Moreover, the canvases can have a texture for natural fibers.

Finishing the fireplace plasterboard with their own hands is a simple process, but has a number of subtleties. For falsecamines, thermal insulation and solid foundation are not required. It is enough just to build a plasterboard portal and pick up a suitable finish finish. In the case of functions, it is recommended to turn to professionals that will perform high-quality installation, which will ensure the reliability of equipment and fire safety.

Imitation of fire in the fireplace do it yourself

Imitation of fire in the fireplace with her own hands Many love to look at the fire. At the same time, not every person can afford to have a real fireplace in the house with a real flame in the focus. But today,

The flame dance fascinates with the changeable dynamics of bends. The pagan views of distant ancestors take a forgotten memories. The ancestors considered the fire by the majestic God. And, despite the fact that we domesticated and tamed this terrible phenomenon of nature, the greatness of fire makes admire them again and again.

And the atmosphere of the house with a hearth is completely recreated and imitation of the flame. In this article we will talk to exactly about, that is, about safe ways without an open big flame, unlike biocamines, which are also successfully used to decorate the premises, but have a real fire.

"Fireplace: imitation of the flame steam

On the video you can see the flame created by the ferry.

This method is the most difficult of the above, it requires electrician skills and special components. Here they are:

Fan 90 mm;
DMX controller VELLEMAN K8062;
DMX decoder Besten DMX Decoder 350;
LED RGB lamp MD-9P;
3 Chinese ultrasound fog generators

For this principle, some concert devices are made, as well as steam electrograms. Imitation with a cold highlighted pair is almost indistinguishable from the real dance of fire. And the cost of our assembly is an order of magnitude lower than the cost of the finished electrocamine. If you decide to take advantage of this method, keep in mind that the design will be built into the false fireplace, that is, it is necessary to provide the appropriate space.
Assembly scheme:
At the bottom of the container under water, we install a pre-assembled fog generator. The generator is equipped with a membrane, which, vibrating with an ultrasonic frequency, creates reduced pressure (almost vacuum). In such conditions, water evaporates at room temperature. Cold steam fan climbs upwards, where it is highlighted by LED - lamps.

Assembly of the steam simulator of the flame, see the video below. One of the steam generators in this assembly is equipped with its own light bulbs, so you will see the backlight at the bottom. Fortunately, this lighting does not affect the "flame".

"Theatrical" fire

As clearly out of the name, this method is used in theatrical productions, design of ideas and other things. But we will use them to imitate the flame.

So, we will need:

Large fan (preferably quiet)
Three halogen lamps with reflectors
Three color filters (orange, red and blue)
White light silk flap
Bowl or box for the founding device of our flame

Imitation assembly:

At the bottom of the box or bowls install the fan, the cord is displayed out.

From the flap of the fabric, cut pieces of different sizes. It is desirable that these were triangles of the wrong shape. So the flame will be more realistic.

Fix the flap in the bowl or box around the fan. All, our fire is ready!

Candle fireplace

One of the easiest ways to simulate Flame Fireplace, which has already become almost traditional and favorite designer solution.

His pros is the simplicity of execution and the real fire, for which, unlike the wood focus, it is not necessary to harvest the fuel. Minus - Candle Candles.

To create a candle composition, use several candles of different or identical size. The choice of shape and color depends on the stylistics of the room and the wishes of the owner. In order to repeatedly enhance the effect of a small candle composition, use mirrors. They are facing the inner part of the fireplace. Mirrors installed at an angle to each other create multiple reflections.

Fireplace: Flame Imitation with Christmas Girls

Another rather common way to create fire imitation. Here I will tell you how to make a simulation of a wood focus.

We will need:

Branches of suitable size
Lace (not new, cut with old clothes)
Aluminium foil
Several stones
Christmas electrolycard in yellow, orange or red gamma.

Twigs without skips turn around foil. It is necessary that the lace is subsequently stuck to the branches.

Thoroughly wrapped with lace glue and wind prepared branches in foil. We leave until complete drying (about a day).

Gently cutting a lace case along the branch and remove the blanks.

From the stones in the place of installation of the focus lay out the circle. We put in the middle of the garland, we leave the cord with a fork outside.

We establish our "lace" firewood in the semblance of a fire. You can add multiple stones for the composition. Our focus is ready. We turn on the fork of the garlands into the socket and admire our imitation.

Council : The flame will look natural if the garland will flicker.

Imitation saline lamps

Not the most spectacular, but the most useful imitation. Salt lamp - lamp which is made of a solid raw salt crystal. Inside the lamp - an ordinary electric bulb. When heated, the crystal emits negative ions, so useful for our body. They bind harmful positive ions emitted by home appliances, neutralize tobacco smoke, their influence has a beneficial effect on the atmosphere of the house and well-being of residents. In addition, the pinkish Pakistani salt crystals, highlighted from the inside, resemble warm small lights or large hot coals, and, folded into the bizarre composition, create an original backlight in your fireplace.

These are such simple ways to decorate your home, make it more comfortable and original.

The fire, his fictional languages, as if emptying only by him one famous dance, the time immemorily carrying his message every now living. Live flame gives a man warmly, it means life. And at the same time it can destroy everything around him. It has long been believed that the fire is a symbol of home comfort. But if, in past times, the focus was a mandatory heating dwelling with a functional structure, today it is rather a decorative part, imitation of the photo, presented to your attention, will give a kind of idea of \u200b\u200bhow the artificial symbol of a homely hearth should look like. Not in every country house there is an opportunity to establish a real fireplace, about modern apartments and not worth talking. But this does not mean that you need to completely abandon such a tempting idea.

Artificial fireplaces - dream or reality?

The focus with the lively dangling languages \u200b\u200bof the flame - the dream of many modern people. But what to do, when there is no opportunity to build it on the existing living area? An excellent option will be the simulation of the fireplace.

Do you remember the fairy tale about Pinocchio with the fireman painted on a piece of canvas? To paint the walls, we, of course, do not offer you, but to build cammels with your own hands forces to everyone.

Imitation or country house is possible even with a minimum of money, skills and skills. There are quite a lot of varieties of ornamental designs of a homemade hearth. For their construction use the most different techniques and materials.

Varieties of decorative fireplaces

False fireplaces can be conventionally divided into two types - interior and electric. The first serve as decoration of the room, and due to its smokeless design, based on the burning of ethyl alcohol and the separation of the process of a certain amount of steam, moisturize the air. One of the indisputable advantages in the construction of such models is that it is absolutely optional to use wood or plasterboard. The imitation of fire in the frame covering by laid out around the gas burner of artificial firewood produced from the heat-resistant ceramics. All this design is quite lightweight, easy to operate, does not overload the space of the room in which it is installed, and what is important, does not require chimney.

Electric types of fireplaces are not only the subject of the interior decor, it is also an additional heat source. Very powerful and at the same time economical in consumption of electricity Modern models do not require any particular difficulties in operation and care. Artificial fire in them looks more than natural.

Suitable for creating a fireplace Materials

Consider in more detail how and from what to make an artificial oven. The first thing that comes to mind is imitation of a fireplace of brick or drywall, but they are by no means only. A small overview for the construction of materials will help you decide on the choice. So:

Metal. Ideal for the interior in the style of high-tech. Possessing the skills of working with steel, you can build a false food that will decorate any dwelling.
Imitation of the fireplace in the apartment of plywood, medium-bed fibreboard (MDF) or chipboard (chipboard) is possible in any interior, be it modern, rustic style or any other. All these materials covered with a special protective film can be easily found in all building markets.
Wooden boards are perfectly suitable for the construction of the portal. In order to emphasize all the beauty of the wood, it can be covered with a special veil, suitable in color to the main interior of your apartment, or acrylic varnish.
One of the most popular materials for creating an artificial focus is undoubtedly a brick. The only disadvantage of which can be called what is pretty difficult to avoid the heavyness of the structure, and this, in turn, creates some difficulties in embedding it into the overall interior.
Plasterboard - easy, pleasant material. Imitation of the fireplace from the CCD is ideal for small rooms. With the help of metal products, it is possible to construct absolutely any structure of the fake focus in shape and altitude.
Artificial stone - non-toxic, non-combustible material, is great for creating a portal.

General principles for the construction of a raised fireplace of bricks

Before starting the main work, it is necessary to calculate the height, the width of the future product, as well as determine the place where all this pretty heavy construction will be located.
In order for the imitation of the fireplace with their own hands, it is necessary to make a detailed scheme-drawing of what you want to get in the end.
To build a false port, in principle, any brick: silicate, facing or decorative. Before starting the masonry abundantly moisten it with water to remove excess air. Properly manufactured brick has a smooth smooth structure.
From the corner, along the level, start the masonry. Try to do the same in the width of the seam.
After the solution, fastening the rows of bricks, will eat well, the inner side and the bottom of the portal must be postponed with a special heat-resistant tile.
Now you can start installing the electric heater. Do not forget about safety measures when working with electricity, clearly follow the instructions attached to the instrument.
To decorate the fireplace or leave as it is, depends entirely on your desire. For facing, you can use a stone or any interior ceramic tile.

Materials and tools

You will need:

brick;
mortar for masonry;
building level;
for interior decoration;
electro-, bio or ecological heuter;
building tools;
items for decorating.

The brick imitation of the fireplace will become a real decoration of the room, contributes to the creation of a warm cozy atmosphere. All this will undoubtedly please you and your loved ones. Unfortunately, such a heavy design is not suitable for making small rooms, but it is ideal for a living room or a hall of a country house.

General principles for the construction of a false fireplace of plasterboard

Easy, pleasant in the work of the drywall structure is not suitable for creating a fireplace portal of any shape, width and height. With the help of profiles and guides, you can make any part of it not only direct, but also smoothly curved. In addition, any illumination is easily embedded in the design of this material, which gives it additional features and functionality. The simulation of the fireplace of plasterboardonodinakovo will fit well into any interior of both a large and small residential premises, whether a country house or urban apartment.

Preliminary preparation

The construction of such a focus model is a fairly costly and time-consuming process that requires preliminary training.

The first thing to be done before the start of basic works is to determine the place and type of construction. What it will be, to solve only you. Imitation of the fireplace with her hands from drywall can have a view of a niche embedded in the wall, to be a wall model (that is, mobile) or corner. There are a great set for the design of the framework of the framework, it all depends on your personal addictions and the overall interior of your apartment or at home.

So, the location is selected, the type is determined, it is time to start building a drawing scheme. It is necessary so that you clearly imagine the result, as well as the work order. The existing sketch will definitely help with the calculation of the required materials.

Prepare everything you need, freeing a sufficient amount of space, you can start the installation of the structure.

From drywall

The process of the construction of an artificial focus of drywall can be conventionally divided into several stages:

building a frame;
facing a skeleton of plasterboard;
giving fireplace refractory;
installing the heating element;
decorating the entire design.

Making and facing the frame

The skeleton of the fireplace is manufactured according to the selected parameters from metal products, which, in turn, are attached to the wall or constitute a separate design in the case when mobile, that is, the portable version of the structure is planned. An important point in the construction of a metal profile frame is that the larger the differences of various details of the jumpers, the more stable and the stron is the product itself as a result. The distance between the guides should not exceed 35-40 cm. Typically, difficulties occur during the installation of the so-called arched part of the structure. To give it a smooth bend at the top of the profile, through the same intervals, cuts are made. Then she bends into the arc and attached to the right place. In this way, several smooth bends can be given in this way. Plasterboard imitation of the fireplace, the photo of which is presented in our article, is carried out in this way. After the installation of the base is over, the refractory tile on the inner sides is laid, you can proceed to the trim. How to decorate a false fireplace, whether to draw it up with its backlight, depends only on you.

Materials and tools

You will need:

sheets or trimming of plasterboard;
self-tapping screws, dowels and screws;
metallic profiles guide (you can use corners or wooden rails);
fixtures for cutting metal and drywall;
tool for accurate surface markup (construction level, roulette);
drill and screwdriver;
putty for squeezing;
decorative finish (ceramic tile, wood, artificial stone, etc.);
refractory tile;
heating element;
illumination.

Decorative false fireplaces are an excellent substitute for traditional hearth with open fire. They are safe, energy, beautiful and functional. Imitation of live fire in such a fireplace allows you to create around yourself a truly cozy atmosphere.