Thanks to the development of new technologies, they gradually go into the past such drives as CDs, to shift flash drives and memory cards. Most PC users have a huge number of disks that will never be used. In order not to throw away just so unnecessary discs, they can be used as a material for different crafts. One of these products may be the chandelier with your own hands from the disks.

Chandelier design

To make a high-quality and beautiful chandelier, you will need 12 disks that have a double mirror layer. From the tools you will need both drills, pliers and nippers. The disk connection between itself can be carried out using the brackets for which any soft wire or stationery clips fit. As a source of lighting, a 220 volt voltage light bulb is used, screwed into a regular cartridge and suspended to standard mount. The cartridge connects to the circuit with the cord and switch. For the manufacture of high-quality chandeliers, you must perform a number of mandatory operations.

Chandelier manufacturer sequence

1. To accurately drill holes, you must prepare one disk as a stencil. For this, the disk is divided into five equal sectors, and then, retreating from the edge of 5 mm, five holes are drilled, a diameter of 2 or 3 mm.
2. The storage box needs to lay the required number of disks. From above the stencil is stacked and the first hole is drilled through it, passing all the discs through. For fixing, a match or thin wire is inserted into the hole. From the opposite side, another hole will be thrown, which is also fixed. After that, all other openings are drilled.
3. The lamp cartridge is installed in the first disk, in a standard hole that does not require expansion.
4. To secure discs with each other, you need to prepare the fastening brackets in advance, in the amount of 30 pieces. For three brackets, approximately one stationery clip is used. Their manufacture is made using bruises and pliers.
5. The assembly of the lamp is performed in series using the brackets inserted into the hole and bent from the inside. Discs on brackets must be completely free to other CDs.
6. Before fixing the adjacent discs, an electrolymppa is installed inside the lamp. Lamps are best suited, although they do not give enough sharp shadows.
7. After fixing the last disks, the lamp can be installed on a predetermined place.

How to make a paper lamp

Resize

How to make a laser disk laser?

Today, plastic discs have emerged massively.

Naturally, the question of their disposal was closely. However, it is easy to throw them out, all the more so that there is the possibility of their completely rational use.

Today we will tell you how beautiful chandelier can be created from the disks with their own hands. Use discs with their reflective light surface for such purposes - by itself a suggestion decision.

What do you need to make a chandelier from the disks?

For the simplest chandelier, dozen disks with a double-sided mirror layer will require their own hands.

From the tool it is worth stocking screwdriver.

Drill for 2-3 millimeters, plumbing and pliers.

For the manufacture of connecting brackets, you need any kind of sufficiently soft wire, you can use the stationery-well-known stationery clips.

As a source of illumination of the optimal electrollamp by 220 volts, with the Mignon cartridge and an equally standard mount to the suspension.

Connecting the cartridge is made using a wire with a built-in switch.

Of course, you can try to make a plug-in lamp and connect a chandelier to a double switch, however, for not too an experienced homemade master, such a job may be difficult, although you can try.

In principle, it is possible to create a multilapampous chandelier from the disks with your own hands by assembling it on the frame of several single-band lamps, best of all of the three, and then connect this chandelier to a double switch.

How to make a stencil for chandelier from CD?

At the first stage, you will need to prepare the dish-stencil under the drill hole for the bracket. The transporter needs to measure five sectors with 72 degree angles and at a distance of 5 millimeters from the edge of the disk to drill five holes up to 3 millimeters with a diameter.

Then you need to store the CD storage to lay the disks intended for use.

Through the stencils superimposed on top, all the discs are drilled. In the resulting well, a guide of match or thin wire is inserted. Similarly, four more holes are drilled.

Guides are needed to prevent disk displacement relative to neighbors. The first disc is mounted cartridge from the lamp.

There is no existing hole in the center of necessity, by the way, it is possible besides "minions" to apply simple standard cartridges.

What to fasten discs for chandelier from CD?

To fasten the discs, three dozen fastening brackets will be required. They should have a "P" shape, sizes of 8 per 10 to 8 millimeters.

One stationery standard paper clutch is enough for three brackets. Work is conducted by pliers and nippers. When all the preliminary works are completed, the chandelier assembly itself begins.

Popular brackets are inserted into the holes along the edges of the disks and bend into the inside with the help of pliers.

What lamp is installed in the chandelier from the disks?

Installing the lamp is made before fixing adjacent disks. If it is desirable to get sharp themes, it is worth using the incandescent lamp, but no capacity is not over 25 W.

The use of a more powerful lamp threatens to melting plastic from which discs are made.

I got a stack of unnecessary CDs? Do not throw them away! Of these, you can make a beautiful lamp. In this master class you will learn to make a very inexpensive and eco-friendly lamp from the old CD collection.

Are interested in?

Budget \u003d 500 - 1000 euros
Time \u003d 4 - 8 hours
Tools \u003d is in every home
Difficulty \u003d Easy - Middle Level
Size \u003d diameter 40 cm / height 28 cm

Materials

Do you have old CDs at home, which have long come out of mass use? Do not hurry to throw them out, but rationally use creative purposes. It is a wonderful material from which you can make a lot of useful things for your home, which you have not even guessed. And if you have a lot of them, it's even better. Today we will tell you how to make a lamp from disks with your own hands, spending money only on the consumable material. Following our step-by-step master classes, you can easily make an original bright table and a picture from CDs.

How to make a lamp from disks?

If you caught fire to make an unusual chandelier from CDs, then alternately follow all the actions in our master class, and you will definitely work out.

Materials:

• CDs (approximately 1000 pieces).
• Carved Circle from Feds.
• Steel wire (5 meters long).
• Electric connector (12 pieces).
• Cartridge for the lamp.
• Electric wire.
• Switch + fork.
• Fluorescent lamp.
• Rubber legs (about 3 pieces).
• Silicone transparent sticks (2 pieces).

Instruments:

• Drill.
• Pliers.
• Screwdriver.
• Adhesive gun for silicone.
• Pliers for cutting wire.
• Simple pencil.
• Compass.
• Triangle ruler.

The list is impressive, but believe me, it costs such an excellent result. Now we'll figure it out how to apply all this to make a lamp from the disks.

Preparatory stage

In order to start making Lama from CDs, you need to take into account some useful training tips:

• Before starting work, you need to collect together all the prepared details and check whether all the tools are in stock. If suddenly you found that something is missing, do not panic - the main materials and tools will be found in every home. The remaining parts can be bought at the construction destination shop.
• For the manufacture of such a lamp, a lot of discs will be required. If you do not have so much, then take them from your friends, colleagues at work or classmates. We think they will be only for, as many want to get rid of the unnecessary "hlama", which is sorry to throw away. Therefore, do not hesitate, but ask - you need it for a good deal.
• The size of the connector must correspond to the diameter of the steel wire - it must freely enter the hole of the connector.
• You can buy an already assembled cartridge kit for a lamp with an electric wire, switch and fork. If you did not find this option, then make it yourself, relying on your designer preferences.

Important! Note that the electrical wire must be at least 2 m long. It is better to buy more than then spend time on an additional trip to the store.

• Any fluorescent energy-saving lamp is suitable for work, the power of which you choose.
• Buy only transparent silicone so that there is no place for gluing the material between themselves.
• For work you need to buy 2 biggest sticks.

We make bottom

When you checked the readiness of materials to work, you can begin the main process of manufacturing the lamp from the disks:

1. We take a circle of fiberboard and with the help of a circulation and a ruler divide it into 12 equal sectors. We connect the division points among themselves to schedule the center where the cartridge and steel wire will be inserted.
2. To the bottom firmly screw the rubber legs.
3. Using a drill, drill the holes for the cable.
4. Ticks cut 6 parts of the steel wire, which should be at least 1 meter.
5. Bend each segment of the wire with pliers or visits.
6. Now the entire design made must be attached to the bottom of the future lamp. Fix the rubber legs with suitable bolts and a screwdriver, fix the cartridge in the central hole of the circle from the fiberboard.

Important! At this stage, do not forget to insert the lamp into the cartridge, as then the discs block access to the cartridge. The cartridge must be strictly in the center of the lamp. If it is shifted to the side, then put it in the correct position.

We make a metal grille and scope from the disks:

• Fix 6 arcuate segments of the wire, inserting the ends into the base hole.
• Watch arc with hands or tools to the desired form. We eventually need a design in the form of a sphere.
• With the help of bruises, cut off the extra edges of the wire, we obtain a mesh of 12 wires as a spherical dome.
• Now we are engaged in the rolling disc. Fill the disks first 6 reasons that are located near the center. Place between wire and disk close up silicone from the adhesive pistol. We do such manipulations until the disk stacks are 6 cm in height.

Important! You can not close the first 5 layers of the disks so that then you can easily change the light bulb.

• When finished riding the wheels on 6 rods at the base, we ride further on 6 wires along the edge of the structure, alternating disks with each other. We must have all 12 metal wires.

Important! Each laid disk should lie on two adjacent drives. Make sure that the sequence of their correct overlapping on each other is preserved so that they are planted smoothly and symmetrically.

Top of the lamp:

• When disk stacks reached 26 cm, we wrap each metal end to the center of the structure, slicing all the extra material.
• Now, clamping the edges of the wire, divide the circle into 12 equal sectors. At each of them, we mark 2 points to install the electrical connector for the cable. As a result - there should be 24 holes.

Important! Do not forget to make sure that the holes come to your connectors.

• In order to pull 12 connectors, disassemble the connector.
• We collect the top of the design. We put on the connectors on the wires and fix the upper case on the top using the bolts and a screwdriver.

Everything, the lamp from CDs is ready to use! Now it can be turned on and enjoy a pleasant muffled lighting!

Important! If you want to make a multi-block lamp, you need to connect the lamp on a double switch, where the wires from all light bulbs will be gather alone in three twists. One wire must be connected to zero, and two others - to the other remaining wires.

How to make a picture of a "liquefaction" from CDs?

Why not make pictures from disks with your own hands? Now we will tell you in detail how it is easy to arrange one of the options. In this master class, everything is written more than detail, so you will not have additional questions.

So, we will need:

• Three-layer cardboard or plywood slice.
• CD discs and their boxes.
• Stationery knife.
• Scissors.
• Line.
• Pliers.
• Watercolor and stained glass paints.
• Figure, printed on a printer or hand drawn.
• Polymer glue.

We start creating a picture of the "liquefaction" from the disks:

1. We are determined with the sizes of our picture. For example, take a diameter of 50 cm. After that, we take the cardboard of the appropriate size and draw two circles - a large and small inside it. In our case, the outer diameter of the circle is 50 cm, and internal - 43 cm. The resulting bezel will serve as a frame for the future picture. The inner circle can be cut as at this stage, and a little later - there is already to solve you.
2. Now we are looking for a suitable drawing on the Internet in a black and white version, print it on the printer and take out gently. Apply the image into the inner circle to check the size match.
3. On the cardboard, we supply the climax and cut out the workpiece.
4. Since we will use a mosaic for our picture, then you need to lay out parts of the disks in an arbitrary order, leaving the gaps, and then fill the emptiness with stained in paints.
5. We lay out a mosaic from the disks. Take a black box from a CD and a stationery knife cutting the stripes to get individual pieces. Using pliers, bow the parts from the black packaging and stick to the cardboard, forming a portion of the tilt.
6. According to the same scheme, we cut the belly of the tales and paint it with white paint.
7. Now we need to make the sea - the pattern of the paintings. We take the disk into hand, cutting it into two parts by the stationery knife. Now it is clearly seen that the surface of the disk consists of three layers - two outer transparent covers and foil in the middle.
8. Next, it is necessary to divide the layers of plastic to get two. The foil should remain on each of the disk layers. From this layer, we will lay out the mosaic.
9. The stationery knife is cutting a part of the disk with a shiny foil on the details of different sizes and shapes.
10. We glue the mosaic sea around the taway, filling the entire diameter of the circle.
11. Stained in paints fill the emptiness between the mosaic. Do not be afraid that the paint after drying will be a little different color - it is completely normal.
12. Using cutlery napkins, we glue the protruding edge so that the cardboard is not visible.
13. On the edge of the whole painting glue black pieces of disk box. As a result - there should be a black rim around the mosaic sea.
14. Mind the paint gaps between the blacks of the rim.

That's all, a gorgeous picture from disks is ready! Now you can hang her on the wall and admire your creation!

CDs are rarely used to record data, but many have preserved these media. The overflowing surface allows them to be used to make beautiful interior items. Some wizards can make a lamp from disks with their own hands. It can be constructed and a person without special skills.

Required tools and materials

To make a lamp of old disks, the following materials will be needed:

• about 1000 CDs;
• the circle of fiberboard, the diameter of which is 20 cm, and the thickness is 1.5-2 cm;
• steel wire with a diameter of 2 mm and a length of 5 m;
• 12 electrical connectors selected taking into account the diameter of the steel wire;
• fluorescent lamp;
• 3 rubber legs with a diameter of 2 cm;
• cartridge for the lamp;
• 2 m electrical wire with a fork;
• switch;
• pistol with liquid silicone.

Tools that will help collect the product:

• compass;
• triangle line;
• marker;
• simple pencil;
• hot glue for silicone;
• ticks;
• screwdriver;
• pliers;
• drill.

Manufacturing process

After everything you need prepared, you can start making a desktop lamp.

Preparatory stage

Before you start, you need to collect all the tools and materials in one place (for example, on the table). If something is missing, then:

• CDs can be found not only in the closet, they want to get rid of many of your friends, they will gladly share with you these unnecessary objects;
• the circle for the base can be cut out of a piece of plywood or take a stand from the old lamp;
• circul and triangular ruler - borrow from any schoolchild or buy, since they are inexpensive;
• the rest of the materials are in the construction store;
• tools can be asked from acquaintances if it does not work - you will also have to purchase.

We make bottom

To independently make the bottom of the lamp, you need to take a round billet from the fiberboard and using a ruler and circulation to divide it into 12 sectors. To do this, it is necessary to conduct 2 perpendicular lines passing through the center of the circle, and then measure the length of 1 from the radius. Putting a feet of a circulation into each of the 4 points on the rim and having sedodes passing through it, you can get serifs. When connecting them to the center of the circle, the borders of 12 sectors are obtained.

In the center of the bottom it is necessary to drill a hole for the wire through which the lamp cartridge will be inserted. The position of the clamping cartridge in the workpiece should be fixed with liquid silicone. You also need to make 6 holes for steel wires on which discs will be located. Then the rubber legs are screwed to the base with bolts and screwdrivers, and the cartridge is fixed into the central hole.

Tighten discs for chandeliers and form a frame

In the holes located along the edges of the circle of the Fiberboard, you need to insert 6 segments of the steel wire and fasten them there. The length of each segment should be at least 1 m. The edges of the wire must be beatened so that their upper parts are connected in the form of a hemispheric dome, and the lower half lift, leaving straight. 12 segments of 50 cm wires should be tied up above the base: 6 curved and 6 straight lines.

The curved segments should be located closer to the center, so they need to be filled with disks in 1 line. The plates will be superimposed on each other, so their overlay should be alternating: to 1 rod to impose 3 circles, then 3 and 5 - 3, after that, after 2, 4 and 6 rod to wear 3 discs, etc. Each round plate should lie on 2 adjacent. It is important to ensure that the discs are located smoothly and symmetrically. Their layers can be fixed with liquid silicone, pouring it between the rods and the central holes of the plates.

After the height of the columns is 6 cm, you need to screw the light bulb into the cartridge. Then you can drive 6 disks at once on the straight wires and slicing with silicone every 10 layers.

Important! The glue for this purpose is not necessary, it will damage plastic components.

When 20 cm remains until the end of the rod, you should go to the curved wires and drive 3 disks on them, as the bottom of the design. These layers should not be fixed with silicone so that there was an opportunity to change the light bulb. Thus laid 6 minutes later. To make a chandelier from the disks, it is necessary to check the symmetry of their overlay all the time. After the correction of the uneven layers, you can move to the next stage of work.

We collect the top of the construction

Each end of the wire must be wrapped to the center, unnecessary parts can be trimmed. After that, you need to take a circle of 2 glued disks and divide it with a marker on 12 sectors as well as the bottom of the lamp. On the inner circle of CD (closer to its center) on the lines denoting the boundaries of the sectors, it is necessary to put 2 points. The distance between them should be calculated taking into account the size of the connectors. These marks are needed to install electrical cable connectors.

Using a drill, you must carefully drill holes at the location of the points. The residues of the markup are better to erase with alcohol-containing fluid. The electrical connector should be disassembled and take 12 connectors from there. Each of them must be put on the wire and secure the top discs with a screwdriver with a screwdriver.

What lamp is installed in the chandelier from the disks?

In the lamp from the disks, you can screw any fluorescent energy-saving lamp suitable for the cartridge installed in it. It should not touch the discs. In order for CDs to not become fragile during operation, it is better to use a light bulb, the power of which does not exceed 25 watts.

Connecting the lamp from CD to the electrical network

Due to weight, the manufactured frame is not suitable for use as a chandelier. It is better to install it on a flat horizontal surface as a desktop lamp.

There is nothing complicated in the construction of the design to the network. To do this, you will need a cartridge, wire and fork. The cable must have good insulation. This will avoid short circuit. For 1 end of the wire you need to fasten the plug, and to 2 - connect the bulb cartridge. If everything is done correctly when the plug is stuck into the outlet, the device must work. If you wish, you can set the switch on the cable.

The table lamp from the CD is best declaring the air-style interior, but it will look good in rooms decorated in other modern areas of designer art.