I want to cook in the garage of the workbench. Flooring, as in the workshop.
To cook on it, and sharpe, and fasten the tisks, and fold tools in the boxes.

Managed to visualize their intentions. Long moved different layout options and prevented the dimensions. I think I found an optimal option for myself.

Blue indicates metal parts, yellow - wooden.
The tabletop will be made of a 50mm thick board, condensed with a 60x50x4 corner and covered with a metal sheet 2mm. The framework of the workbench will be welded from the profile pipe 60x40x2. Stiffness ribs will be cooked from the corner 40x40x4. Shelves and side panels will be made of 30mm thick boards. From the 40x4 strip will be made guides for fastening side panels. Boxes will be welded from metal 2mm and installed on powerful sleds.

To purchase a metal, we agreed with wild on two to order a gazelle to pay less, and on Saturday at 8:30 am, so as not to stretch it for the whole day, went to the metal base.

The weather was slimy and cold wind. Loader in Rvan Army Bushlak, which suffered from a hangover syndrome, pulled a wet metal for cutting. A dirty carrying was lying around in the pool with a grinder connected to it. Sliced \u200b\u200bpieces of metaloprinkate spacked into a slushful puddle. Nearby expected ordered Gazelle. Light.

Do not consider me by the maniac, but after arriving in the garage, I soap water and wiped dry chumased chumased pieces of fresh metal. All the same it is brushing it before painting, and so it will be more pleasant to work with it.

At that severe January morning were bought:
1. Corner 50x50x4 6.4 meters
2. Pipe 60x40x2 24 meters
3. Corner 40x40x4 6.75 meters
4. Strip 40x4 8 meters
A total of 121 kilograms of metal for 4000 rubles.
Now I will cook your workbench.

The cutting of the main parts of the carcass took two evenings, a total of five hours.
In total, it turns out that the skeleton of the workbench will consist of 45 cooked parts.
On the tags it is indicated that it is and where to weld it.

Now you can safely postpone everything in a long box and surrendered to the thick silent sticky bog of everyday irresponsive routine.

Cooked brackets for the toolbar above the workbench.

And the base is welded for homemade countertops.

Coarse the bases for the table top welded flush with the corner. For this, curly cuts are made in cross-cuts. Here is a small sherchezh, as it looks like:

In the meantime, the brackets of the toolbar.

Lining from 4mm bands strengthened loaded joints.

I welded 24 bracket for side panels. Panels will be plywood - cheaper than metal, and look better.

Brackets give the extra rigidity of the entire design.

I want to cover the tabletop with a sheet of metal 4mm or 5mm. On Moscow Prospekta there is a reference, which metal sheets immediately cut into size. I need a sheet of 2200x750.
If you take a sheet of 2500x1250, then two good pieces will remain (2200x500 and 300x1250) or (2500x500 and 750x300), which can also be chopped into the desired dimensions.
If such pieces are useful to someone, then [b] let's cooperate, and then one is expensive.

From 15mm plywood made drawers. Collected 80mm on screws. In each drawer for 20 screws. It turned out firmly as I love.

Size of each box 0.6m x 0.7m x 0.2m

Salazki fucked welding. He learned to weld a tin 1mm to a 4mm 3mm electrode strip on a current 100 amner. It is how to put in the kitchen processor automotive engine V8 of 3 liters. Just the tig was lazy to discourage. Moreover, it is so secure.

Now I think over different options for facades.

On this welding stage ended. Ahead is carpenter and paint. More little things, plumbing and electrically conductive.

Painting of the carcass homemade workbench.
I asked the seller to advise good paint.
- Wah, what good paint, my mother swear! - He replied stretching the bank of paints on rust with a metal crumb for 500 rubles.

She covered the table top with a cutting board of 150x40. Crepeled boards to a frame of self-drawing 4.0x35. In total, the 60 self-tapping screws.

A bit polished the surface to lay the metal tightly.

Polit about protecting wood from fire. In impregnated wood cannot support burning itself.
When heated with impregnated wood, a melted film is formed, which does not burn and limits oxygen access to the surface. The manufacturer of my impregnation stated the I group of flame retardant efficiency - the highest.

Of course, it does not allow cooking metal directly on the surface of the workbench. The boards still do not light up, then you work. To organize a welding post, I plan to cook a removable grille that reliably protect the surface of the table top from the thermal exposure.

After drying, I will cover the table top of the already harvested sheet of metal 4mm.

She covered a tabletop 4mm sheet metal. The sheet pulled to a wooden basis with a row of screws with a hidden head. The table top turned out to be monumental.

10mm plywood shields covered extra openness in the workbench frame.
In the photo the paint shop.

Prescribed permanent tenants on the table top - a grinding machine and vice. They are lost on a hefty countertop.

1) What is better to cover your bare metal on the table top? I tend to the rust converter, which will create a solid protective film and which is easy to update if necessary. Maybe there are better ideas?
2) where to take a durable chair with an adjustable height?

P.S. I think that reading this branch will be interested - the Bourgeois site with a bunch of welded tables and other welders: http://www.pinterest.com/explore/welding-table/ You can find the process of manufacturing the entire presented.

Nevertheless decided and smeared the tabletop Rust converter. It is necessary to smear a thin uniform layer.

While the countertop slowed down with shelves in the left drawer

Well, in general, it was not a bad idea to smear the countertop. The film really turned out, as if the lacquer was covered. True, it is not very accurate, but it is really easily restored - because The film is easily dissolved by the new portion of the converter and rewinds hiding all the old damage.

From the big one - there is a panel for instruments and place fasteners on it for the whole-only one.
I want to hang the sheet of plywood or one-piece furniture shield with a thickness of 15 mm and the size of 2.2 meters x 1 meter. If anyone has such, I propose an exchange for a metal sheet of 4mm 2.2 meters x 0.5 meters (remained from the tabletop).

Well, in fact, then for what ...

Test passed

Class! It is no longer necessary to use the manual power tools on stools, lay out tools, fasteners, screwdrivers, taps and roulettes on all accessible shelves and catches around and looking for them, forgetting where to put it - everything is in one place and at hand.

Mounted tool panel. Whole, of 21 mm plywood.

4 corner 50x50x4 plus plywood 21mm plus 16 bolts 8x40 equals tens of kilograms of tools without fearing something break

Facades for boxes made 21st plywood

That's all.
Dream workbench is ready. Sometimes something came out curved, but I am very pleased with the result.

The weight of the workbench net exceeded 200 kilograms. Table tops 1.65 square meters, area of \u200b\u200btoolbar 2.2 square meters. The total volume of the left and right Tumb is almost one cubic meter. The peculiarity of the workbench is that you can sit when working with a tig, and a 4mm metal sheet-covered table top is not afraid of mechanical damage. Spacious shelves, boxes and panels allow you to conveniently store almost all the tool available with me, providing convenient quick access to it.
Here is such a homemade dream workbench.
I think there will work my great-grandmothers on it.

P.S. And after a small refinement, a great make-up table is obtained)) -816- http://gazeta-v.ru/catalog/detail/192_vizazhist_i_fotograf/16464_grimernyy_stol_svoimi_rukami/

Well, to put a bold point in the project some more photos.

Self-tapping screws and twisted quickly and easily (if there is a screwdriver, of course).

Over time, brought wrenches, holders for drill and screwdrivers, bracket for paper towels, and additional lighting. The benefit that two square meters there is where to turn around. The thing I smeared awesome. Satisfied Aki Elephant.

First, small vice did not stand the load and burst.

Instead, more powerful vice are installed. On one side, they had a five-pointed star, on the other - the figures 1958 - probably, the year of release. It turns out, they are 56 years old? I hope they will serve me as much. In general, good vice is the pride of the master.

It can be seen in the photo that the tabletop repels not much beyond the size of the walls. Therefore, when fastening the pisses to the bolts it will not work out to be cut down to tighten the nut. I thought so. Things and sharpened on the tabletop using anchor bolts. It looks neat and keeps deadly.

Secondly, it turned out that deep boxes in the right tamba are not very comfortable. It was better to make their smaller size. I will invent some organizers inside them.

The rest turned out to be a great thing. All tools in one place, in sight and are always ready. On the big tabletop also there is where to decompose.

You can purchase some things from this blog in our Vkontakte group:

Washmarket workbench is a working desk with a wide range of destination. It allows for clearance, repair, electrical work, processing of various materials. The workshop should be in any domestic workshop. The masters prefer to design it with their own hands to make the most convenient for themselves.

Composite parts of fixtures

• nuts and screws;
• fire and hammer;
• paint with brush.

The lockable workbench device is a rigid metal base (made of corners or a square tube). To arrange a worktop, it is better to use a 50-millimeter bar. The steel plate with a thickness of up to 6 mm is stuffed on top of it. To fasten all metal parts, use welding, but you can also screw the bolts.

Installation of the workbench frame and base-top

Before proceeding directly to the assembly, look attentively on the prepared drawing. Make sure that the size of the future workbench fit into the size of the room where your plumbing tool will stand (garage, shed or workshop). Installation of the table begins with the creation of a frame:

1. Cut 4 legs of the same size from the corner.
2. Connect them at the top of horizontal crossbars from the same material. Use welding. As a result, a rectangle must be rectangle (top view) of the specified size.
3. Additionally, make a rigidity line, once again covering the legs in the same way with horizontal jumpers at an altitude of 15 cm from the floor.
4. If you have a cabinet with boxes from the table of workbench, then you will breed a couple of additional supports for it.

After that, you can start assembling countertops:

• make around the perimeter of horizontal metal crossbar holes for the bolted compound;
• cut the boards along the length of the table;
• put them with each other without cracks and lumen, secure in this position;
• make holes in wood coinciding with holes in the corner.

Council. From the upper side of the opening boards must have extensions. They will deepen bolt caps, so that the wooden surface of the countertop remains smooth.

Final stage assembly workbench

The table top will be ready after the plating with the metal. To do this, simply cut the fragment of the required size from the prepared sheet and secure it on a wood basis with the help of self-samples. Please note that after their screwing in the metal there may be burrs. They should simply write to the file.

If you have provided in the design of the workbench boxes or shelves, take advantage of the simple technology of their manufacture. The usual 15-millimeter plywood will be suitable as the material. Boxes are harvested on screws. One account for about 15-20 pcs. Shelves are easier to attach to the corner, but for the boxes will have to additionally buy guide strips - Salazks. They are welded to the frame.

The same plywood can be seen the side sides of the table and make the screen on its back side. For greater stability, the wizard is recommended to attach rectangles or pieces of corner from below to the supports. In this case will help the welding machine. If necessary, screw the vice to the workbench. Finally, process all steel paint structural elements for metal to avoid rust.

Make a workbench for metal work is not very easy, but it is quite possible if it is responsible to go to the case. But you will make sure that no purchased table is compared in quality with the product collected by your own hands.

How to make a workbench: video

For the convenience of processing wood, stone, plastic and metal, for finishing and assembly manipulations, a work joiner's workbench is often needed. To make it with your own hands, the drawings will not be required - they are needed for work desks of complex designs, which are also described in this article.

Purpose and typical workbench device

Any workbench is a massive and necessarily stable desktop for processing products of various dimensions. The more its size, the dimensions and heavier items can be processed on it. Moreover, the work itself is performed as a manual tool (with knife, protever, etc.) and mechanized - for example, with an electrical drill or electruruck. The joiner's workbench has the following typical layout:

• The working surface is performed from a massive board, a thickness of at least 60 mm. For the workbench, it is desirable to use solid rocks - beech, rack or oak, otherwise it will have to be periodically changed due to rapid wear. The lid can be led from individual dry boards and before installing the Olife process;
• On the front (facial) part of the top cover "hang out" visks for fastening the processed products. If the linear size of the workbench exceeds 1 meter, you can install two vice - separately for large and small parts. Large vice should be wooden, small permissible in the "steel version";
• Topic supports are made of soft wood - pine or linden. Wooden workbenches are necessarily interconnected by longitudinal planks for the overall stability of the structure;
• On supports in an expanded space, retractable or tightly fixed shelves for tools can be located.

A row holes for installing clamps, wedges and other parts for fasteners are drilled in the front of the top cover. In the rear of the working surface, it includes a deepening - it is intended for small parts and accessories. It is possible to replace the complex in the manufacture of a perimeter of wooden plates.

Homemade workbench can have three types of constructive design:

• Mobile. A small table with dimensions of about 70 per 80 cm in length and width, with one vice and weighing up to 30 kg. The lower parts of the supports are made of metal for additional stability. Designed for small repair and working with light wood products;
• A stationary workbench of a simple design is easy to manufacture, but firmly "tied" to one place. Used to handle heavy boards and massive wooden blanks;
• Compound on bolted connections. It is convenient for its "discerning" and simplicity of the replacement of individual parts, but the manufacture is more complicated by others.

Photo Gallery: Drawings with dimensions and designations

Methods for independent manufacture of stationary and adjustable workbenches Consider more. Stationary laughed in the ground in its own area, in the country or in the yard. If it is installed inside the garage or other working room, it is recommended to attach it well to the floor so that the workbench did not swing during operation.

The assembly sequence is as follows:

1. The base is a frame of wooden bars, which is fastened so that the structure is as a result as reliable as possible. To do this, you need to arrange a jumper between the legs, and in the middle to install the kingu. They are best arranged at a distance of about 40 cm from the floor level. By the way, they will also be suitable for creating additional shelves. Brussia is combined with the help of construction glue. Where it is impossible to carry out such work, you need to operate the screws. If you are going to make a disassembly tool, it is best to connect with metal corners. In any case, all the grooves are first prepared, then the design is assembled, the glue is processed by the compounds, fix them with clamps. The best option for a stationary workbench is considered the possibility of part of the instrument to attach to the wall for reliability.

   The base is a frame from BRUSEV

2. If you build a tabletop from several boards, it is important to make it high quality as high quality so that garbage and sawdust fall into the gaps. The dimensions must exceed the width and the length of the base by 3-5 cm - this will allow with all the amenities to clean the tool.
3. The countertop is screwed and nailed to several boards, which are on the other side of the working surface, and at the base it is necessary to place the grooves for mounting bars.

   Boards are attached to a steady frame

4. The desktop should be put in order with the help of a grinding machine, cover the oil to reduce the risk of injury from pinch, and metal corners are screwed to its base bolts.
5. To the already made working surface is a clinium vice, which should be created in the working surface, this will allow you to position the vertical plate into one plane with the worktop. From the bottom side, we establish a plywood gasket, while it is important to make that the lips of the vice are located at one level with the surface. Applying a vice, mark the site where the holes will be drilled, and attach them with nuts. Pre-milling holes so that the bolts in them "stop". It is best to install vice not at the corners, which will make them reliable even subject to lags.

   To the surface of the workbench, you can attach a vice or saw

6. In addition to vice, you must do and stops. Of course, they can be made independently, but it is better to purchase and ready. However, if you decide to create them with your own hands, prepare rectangular stops that can be adjusted in height. Bolts should not be used because they can damage the workpiece when working. On the working surface, we do the holes for the stops, while it is desirable to be located at a distance of up to 50% of the progress - this will allow you to securely secure any billets.

Video: Vistak with vice

Video: Desktop with saw

How to make a simple joiner workbench do it yourself

1. The top cover is peeled from thick boards, from which a massive shield of 70 cm wide and up to 2 meters should be turned out. For fasteners, long nails are used, driven into the boards with the "facade" side and carefully bend on the wrong wooden jumpers. The work surface of the workbench is necessarily performed from a wooden array, fiberboard, chipboard and other materials from pressed chips for it categorically not suitable.
2. A good constructive solution will be the cover of the lid along the bottom perimeter of the 5 cm with 5 cm - subsequently, it is convenient to fix vertical supports to it. Increased severity of the cover will only give additional stability to the entire construction.
3. The location of the top cover of our workbench depends on the location of the vertical supports. It is advisable to make them from a rectangular timber with dimensions from 120 by 120 mm. You can take as a support and round forest, but its fasteners are not so reliable as in square (rectangular) bars. Of great importance is the height of the working surface, the convenience of carpentry manipulations depends on it.
4. Optimally install the upper slice of the supports at the level of lowered down hands - due to the installation of the cover, the overall height of the workbench "grows up" by 7-10 cm and work on it is quite convenient. On Earth, we carry out the markup to the wells for vertical supports and dig them to a depth of 25-30 cm. Accordingly, the total length of the bars of bars is 1.2-1.3 meters.
5. Vertical bars are installed in the dug holes exactly, strictly in the construction level. The installed supports are connected in pairs using wide boards at an altitude of 20-40 cm. The transverse boards are attached to vertical bars with long screws. After that, the operating surface is mounted on the ends of the supports. For its installation, self-supersubs are used, since the hammer blows on nails can move the framework of our design.
6. When the upper cover is securely fixed, you can "hang" vice, clamps and other devices for the convenience of joinery.

If the design is more complicated

In the manufacture of a composite joiner's workbench with their own hands, the drawings will be required, although the manufacturer's procedure itself is largely similar to the above. The main differences are related to the use of bolted connections instead of self-sufficient screws and mounting boxes for the tool in an expanded space.

When the installation of the vertical support is completed, they are connected to among themselves horizontal jumpers. Previously in each jumper with the help of the chisels and the hammer, the grooves under the nut with a washer (you can use special furniture bolts with C-shaped nuts). By setting a bar-jumper to the height, a through hole in which a long bolt is inserted in the vertical support and the horizontal bar is drilled. From the side of the prepared groove on the bolt "Introduced" the nut with the washer and is thoroughly dragged on the thread.

Horizontal jumpers for the framework of the collapsible workbench will be required two from all four sides. In addition, it is necessary to set 1-2 jumpers in the middle of the table, directly under it. Horizontal rails are attached to these additional jumpers for small self-tapping screws, which will slide drawers for the tool. The boxes themselves are manufactured "at the place", that is, depending on the size of the assembly lumen between the jumpers.

The working cover of the collapsible workbench is also attached on the bolts. In the rapid part of the vertical supports with the help of the chisel, the mounting recess is hosted, the holes under the bolts are drilled in the lid. Because A smooth working surface is necessary, the heads of the bolts are "combed" in the lid due to the drills of the appropriate diameter drills drill.

Video: how to make an independent milling table

The indisputable advantage of the collapsible workbench is not only in the easy replacement of parts and the table top. As is known, under the load from planing, drilling, with another mechanical processing, the most durable workbench is loosened. It is much more reliable and easier to re-tighten the fastening bolts than to drive new nails or screws into the wood - so the collapsible models serve much longer than the incomplete analogues.

Video: folding table workbench

The design of the joinery will be dependent on your needs. In order to make it with your own hands, sufficiently minimal knowledge and skills.

All photos from the article

Carrying out carpentry work in your home, any amateur master must have a convenient device for them. It will be a guarantee of comfort and security of your activity, and also significantly intensifies it.

Our article is devoted to how to make a work workrid on your own.

Typical Desktop Desktop

The joiner's workbench is essentially a massive and extremely stable desk at which wooden blanks of different sizes occur. The device is more, the more severe and overall elements can be processed on it.

At the same time, it is possible to work on it with manual instruments: saw, chisel, cornotch, etc., as well as mechanical: electric jigsaw, branches, drill, etc.

Layout elements

The workbench for working with the tree has the following typical elements.

1. Working surface (countertop, cover) is made from boards. They must be dry and have a thickness of at least 5 - 6 cm. The optimal option is to use oak impregnated: Oak, Grab, beech. Otherwise, the lid will quickly wear out.
2. On the front side of the countertops are installed vice for fixing blanks.

Note! If the length of the workbench is more than one meter, it is best to hang a couple of different vice for handling small and large elements. Large vice can be made of wood, and small metal.

1. Supports (legs) are usually made of soft breeds: linden, pines, maple, etc. They mate with each other longitudinally located planks. So the design acquires strength and stability.
2. With fixation on the supports in the space below the table of the workbench, you can accommodate the retractable or fixed tightness shelves, drawers or cabinets for the toolkit.
3. On the front of the countertop before making a workbench on a tree, drill holes for mounted wedges, clamps and other devices for fixing overall blanks.
4. On the back side of the lid, it is necessary to make a deepening needed to handle small parts.

For any economic man you need your equipped workplace for storing the tool and performing carpentry-fitting works. In this case, the vestic will simply become a necessary element of the workplace, and now we will tell you how to make a workbench on your own.

In contact with

Odnoklassniki.

Indeed, to buy it, you will need to post a considerable amount and, in addition, it is necessary to choose the desired size for your premises, it seems quite difficult task. But if you do it yourself, you can choose the desired workbench size up to centimeter.

What workbenches are there

The workbench is a desktop where the master produces manual work on the processing of wooden, metal and other parts. Independent workbenches are installed in the garage, in the country and even in the apartment. The workbench is equipped with various additional devices that may be needed when working, such as stops and vice. In addition, in the workbenches set the containers for storing various tools and even documentation. According to the type of work, carpentry, carpentry and plumbing workbenches are distinguished.

Vistak your hands video:

Carpentry workbench

Standard joinery workbench has such a design. The main parts are the vertical stove and an exposure. The exposure looks like a rack (usually two), which are interconnected by wooden bars. The material of this table element is usually pine or other wood of soft breeds.

The vertical board or cover is made of solid wood, for example, oak, and has a thickness of up to 8 cm. The surface of the board is covered with oil. If you are going to collect workbenches with your own hands, then you need to know which additional devices need to be installed on the tabletop.

Note!

First of all, it must be vice located in front and used for fixing parts.

In the back it is necessary to make a deepening, for storing a small tool in it. At the edge of the brandy board there are holes in which wooden chiochk and metal combs are inserted. The standard workbench is mostly suitable for handmade, and if you want to use the power tools, then for this you need to choose a backplane with a large number of holes for the stops.

Floating workbench

Flooring workbench is a more powerful building. It has a metal frame to which the wooden cover is stacked with a thickness of up to 6 cm and covered with an iron sheet. The cover is edged with a trilateral side and on it, in most cases, plumbing vices are installed. The tabletop on such workbenks is made powerful so that it can withstand high shock loads, including sledgehammes.

The material is chosen as desired, but the most popular MDF with galvanized, which allows the worktop to protect the aggressive environment, such as gasoline, oil or solvents. In addition, such a tabletop is easily cleaned by contaminants. Merchant workbench is equipped with several advanced tool folding boxes.

Carpentry Vistak

Another type of such design is a carpenter's workbench. This workplace is intended for processing boards and has dimensions significantly exceeding two previous options. Its dimensions have a length of up to 6 m and the width of 1 m. On a carpenter, the stop is necessarily installed for the processing of the board. It has a cutout in the form of a triangle, to secure the board using wedges, and is used during the processing of its edges.

Manufacturing a building workbench

Let's figure it out how to make a joiner's workshop with your own hands. First, it is necessary to make a frame of bars, and between the legs, for strength, set the jumper and the kingu (connecting element, fastening the design). It is desirable that they are located at a distance of about 45 cm from the floor. Installation of the workbench frame takes place in this order. First you need to prepare the grooves, then we collect the design and scroll through the connection points with glue. Final fasteners are carried out using clamps.

Countertop for workbench

It is worth recalling that the manufacture of any design happens more quickly and efficiently if you have at least the easiest drawing of the joinery or part. Below we give the drawing of the table top, top view.

If the countertop is made of several boards, then it is necessary to ensure the absence of cracks between them, to avoid, when subsequent work, scoring a dust there. The size of the countertops should be more than 3-5 cm of the workbench itself, for more convenience tool cleaning. The countertop must be treated with grinding and covered with varnish. It will serve as protection against hitting the head of hand.

Installation of vice and creation of stops

After we installed the worktop, you need to mount the vice. To do this, on the working surface you need to cut a deepening so that you can put the vertical plate in one plane with the tabletop. We put a vice in the place where they will stand in the future, it is desirable that it was not an angle, and we make a bandwidth. Then screw the nuts.

Note!

The stops can be purchased in the store, and you can do it yourself.

Then we advise you to make their rectangular shape with the possibility of adjusting height. Holes under the stops are desirable to produce a length of 50% of the pricks. With such a situation, you can fix various blanks well. Video instructions for the manufacture of workbench can be viewed in our article.

Wooden workbench

Making a locksmith vestica

Let's look at how you can make a plumbing workbench with your own hands.

1. Determine the height of the future table. For each person, it can be different, for example, if a man has an height of 180 cm, the height of the workbench is 90 cm. But still, it is necessary to focus only for the final decision.
2. Do not forget that the drawings of the locksmith vestica drawn by you will be useful for a faster and high-quality assembly.
3. For a locksmith workrist, the frame is best welded from the profile pipe and corners, but in the extreme case it can be done in the same way as a carpentry structure, from BRUSEV.
4. In order for the construction to be the most durable, you need to put between the legs of the strut. Sometimes, instead of struts, a shelf is installed, into which in the subsequent can be folded tool, paints and varnishes or other necessary items.
5. For the resistance of the design, you can attach legs to the floor. This will exclude the hint of the workbench when working.
6. Build a tabletop from MDF and, if possible, galvanize. This will significantly increase its strength.
7. If you want your workbench to be equipped with drawers, then put the rods under the upper bars, similar to those that are installed for the boxes in. Then you will have a storage place for small parts, screws and nails.

Folding workbench

There is another variety of workbenches that are used for both carpentry and plumbing works. This is a folding workbench. It is very convenient if there is no unnecessary area indoors. Working on it, it can always be folded and put it in an angle to expect the next work. In addition, it can be converted to the cottage in the folded state. Such a workbench consists of two parts: a removable brandy board and folding table. It is usually manufactured smaller than a stationary table.

Vistak your hands video:

In contact with

See inaccuracies, incomplete or wrong information? Do you know how to make an article better?

Want to offer photos on the topic?

Please help us make the site better! Leave the message and your contacts in the comments - we will contact you and make a publication better together!