Crawling of sockets and switches Wallpaper - one of the basic techniques. That is, anyone who makes work on the walls of the walls must be able to get around the socket, switch, frame or other element at a sufficient professional level, and not too thinking how to do it.

Immediately for reference: In work on pasting and surface preparation, this operation is not included, and if you estimate the object, the bypass of the elements should be taken separately (as, however, and in the case of C). Now we'll figure it out in the practical part.

So, bypassing switches and sockets, that is, the pasting of their wallpaper (or space under them) can be done in two ways. This is actually disassembling and trimming. In the first case, the element is dismantled (partially), in the second - the wallpaper is trimmed around it. Consider both methods:

Method for the first: partial disassembly (prayer)

In this case, it is necessary to remove the front panel of the socket, switch, etc., leaving the contact group in the mounting hole or box. This method Allows you to make the most accurate and accurate bypass and takes about a little time. It is strongly recommended to act in most cases in this way.

The technology is simple: unscrew the screw (in the case of a socket), or use the screwdriver with a screwdriver and then unscrew the screws (in the case of the switch), remove the panel and insulate the contact group using a polyethylene bag or painting tape:

If the group is not exceeded, and the contacts will be open, then you risk getting a shock after during pasting from the phase stroke and the adhesive film will rise to your fingers. Therefore, it is categorically contraindicated to produce walls of the walls with open sockets.

Switches are isolated similarly. True, it is not always possible to disassemble them likewise, since it is sometimes necessary to completely remove the switch from the socket in order to remove the front panel. Therefore, in relation to such elements, the cutting method is sometimes used.

In the case when the contact group is deep in the technological hole (more often it happens when the outlets are old - this case is shown in the photo with a bag), then the wallpaper cuts forward very gently with a knife only after dried:

Method of the second: trimming around the element

The essence of this technology is that the cloth is glued to the element from above, and then this element through special cross-shaped slots is extracted out. After that, the edge around the element (in this case of the switch) is trimmed by a hypochetic knife, it is neatly poured under the front panel and remains in this state.

The method requires almost surgical accuracy, therefore, before acting, it is worth thinking well - maybe dismantle the switch will completely be easier? If you still decided to apply trimming instead of diagrams, then consider the following points:

1. Wet, moisted with glue wallpaper badly cut, so any incorrect movement of the knife can spoil all the work. The blade should be very sharp (it is necessary to break the segment before under trimming), the hand should not be twisted.

2. When you glue the cloth, under which the switch is located, then first before himthen perform cruciform slots and only then smooth the canvas after switch. When the trimming is made, you should align and block all the folds and remove the web shifting if they are.

Finally, if you, swinging too zealous with a knife, spoiled all the work, then we will have scissors cut frame From wallpaper and paste it around the switch. You can also buy a ready-made frame in the store, and since it is usually transparent, then you can save it to self-tech or soaring from the inside with a shallow eye (grain 400), or come up with something else.

On this material on pasting with wall outlets and switches is completed. Make this technique can almost everyone, the main thing - carefully act, not to be afraid and carefully count the movement. Well, be sure to comply with the safety technique so that you do not seek the current.

For those who make repair on their own, often wondering how to do it. Glue wallpaper near sockets and switches It is necessary to carefully and follow safety rules. If you are afraid of electricity, turn off the switch at the time.

Before starting work, you remove the front panel of the switch or socket. But do not forget to leave the box with the mounting group. Then unscrew the screw. Gently remove the panel and with the help of painting tape is insulating the contact group.

If you do not do this, that is, the high probability that you will hit the current during the shocking of the wallpaper.

Switches you must also isolate. If it failed to do, then you can use the trimming method.

Condition is the following. You stick the wallpaper cloth on the switch or the outlet on top. Then, through the cross-shaped slots, retrieve out. With the help of the knife, the wallpaper edge is trimmed and it is very gently removed.

You need to perform all actions accurately and gently. Also during trimming, consider the following:

- Remember that the wet wallpaper cut is quite difficult and one incorrect movement can lead to a ruffled type of work. For this, you need a knife with a sharp blade.

- When you glue the wallpaper on a socket or the switch do not forget to thoroughly smooth out the plot to them and after them, and only after that make cruciform cuts.

You have the opportunity to order electrical equipment with delivery in a rather short time, and you will be satisfied with the service. If you cut the edge unevenly, you can disguise your errors using a special framework. You can purchase them in building stores.

And doubt your strength? Tips for experienced specialists will help avoid errors when performing work in complex places: around switches and sockets.

Glue wallpaper around sockets and switches is not so difficult

Preparatory work: do not forget about security

The easiest all around the switch and sockets after partial dismantling of electrical appliances. Before starting this work, de-energize the room, and then:

• unscrew the screws and remove the socket protective cover. Contact group in the mounting submergene leaves on site
• carefully approach a screwdriver or a small chisel key of the switch, remove the decorative panel frame from it
• inseal open screw clamps with wires with a painted tape or secure them with dense polyethylene, reflecting the ends into the technical hole.

Without the insulation of the contact group, it is categorically prohibited in order to avoid electric shock from shock.

Casting wallpaper near sockets

The next step is the immediate wintication of the walls. On the sliced \u200b\u200bcloth and it is attached to the wall on top of the technical opening. The band is thoroughly gripped with a roller or a rag, after which the contours of the opposition becomes clearly visible. Now it is necessary to cross the cloth in the specified place with a sharp wallpaper knife. The valves are neatly refilled into the hole.

Under round electrical appliances, cuts should be made of stupid, to wrap trimming was more convenient. Special scrupulousness when performing this technological operation When crawling outlets and switches is not required, because after installation decorative panel Ogrechi will be invisible.

ATTENTION: When using wallpapers with metallized elements, the cut hole should be made more accurately, do not allow contact with electrical pipelines. Aluminium foilUsed in their production, can play the role of the electrical conductory.

Glue wallpaper near switches

Some switches have a complex design, and their disassembly is not possible without the complete removal of the mechanism from the mounting box. In this case in hard to reach places Recommends to use trimming, without removing the protective panel.

The measured cloth is attached to the wall only to the location of the switch. Plugs, which serve as a guide to perform a cruciform hole in the corners of the switch of the switch are performed. After performing a cut, the spatula is tightly pressed the edge of the formed valve to the wall around the perimeter of the switch frame. Surplus are cut through a spatula or metal line, carefully roll the edges of the hole to the wall. And only after that the remaining part of the panels is glued.

More vividly similar technology demonstrates a short one-minute video:

This method requires a certain skill and, while round rosettes are particularly difficult.

What to do, if …

If you carefully studied all the materials on how to enclose wallpaper in complex places, but the results of the work performed are not pleased, then you can:

• additionally cut from wallpaper remnants or (optional) contrast finishing material Masking overlay. It is performed taking into account the exact dimensions of the electrical appliances and is glued onto the wall, decorating non-accurant cuts;
• purchase in the store and set the finished decorative polymer or silicone frame near the switch, which will not only hide defective places, but also protects the wallpaper from contamination during operation.
• convey this work to us . Call now, our masters will come to you within 2 hours and will fulfill all the work quickly! To familiarize yourself with the cost, go to.

Switches designed to switch the mode of operation of lighting indoors are characterized by a high margin of strength. Therefore, they can serve a very long time. However, sometimes there are situations when it is required to remove this element from the wall, for example, for sticking wallpaper or replacement to a new and improved model. The whole process will take 20 minutes from the strength, and even a person who has encountered for the first time with such a necessity. The main thing here is to adhere to the safety rules, as well as perform all actions very carefully and carefully. After all, the switch is 90% composed of plastic elements, which damage which in incompetent appeal will not be difficult.

Remove the switch from the wall - what to pay attention to first

For starters, take care of the presence of special thin rubber gloves, without which it is not recommended to work. After that, you can proceed directly to the dismantling process. To properly remove the switch from the wall, you need to figure out in some of the features of the process.

It is necessary to highlight such important moments as:

• Safety machines. The network connects to the apartment through fuse plugs or current protection machines. Before starting work, it is required to de-energize the voltage, for which the automatic toggle switch is translated to the lower position. If there are traffic jams in the camshaft, then you will need to turn them off by clicking on the red button located nearby, as well as unscrew from the cartridge both traffic jams that are responsible for zero wire and phase.
• Type of switch. It is also very important moment. To date, a lot of a variety of models that are different additional features – remote control, smooth adjustment and so on. However, for our problem, the value of only the type of fastening is hidden (the switch of the switch is recessed into the concrete) and the outer (the box is screwed to the wall with screws). The first type is somewhat more complicated, so it will be about him.
• Connection diagram. Most often, the light switch is equipped with several keys, which makes it difficult to remove the device from the wall, as the number of wires suitable for each key increases. In addition, the more keys, the longer it is necessary to remove each of these items.

Remove the keys from the switch - the first stage of dismantling

Despite the fact that the process of removal of the switch does not apply to the category of complex, it is recommended to try to invite an electrician. After all, work can be dangerous because you have to deal with electricity. If the challenge of a specialist is not possible, you have to act independently. Before you perform, you need to make sure that it is he failed. Often the problem is in the cartridge, which simply burns out over time.

If the switch will be necessary to dismantle in any case, for example, to shove walls with wallpaper when this item will interfere with work, it will be necessary to completely de-energize the electrical appliance circuit in the apartment. Disregarding the rules of electrical safety can cause the following problems:

1. 1. Fire
2. 2. Wiring insulation test
3. 3. The failure of the instruments connected to the network, as a result of a short circuit
4. 4. Punch current, eye damage, burns.

You must not just turn off the food in the apartment, but also close the shield on the lock. You can also hang a plate on a shield that reports that at the moment work is carried out, which are conjugate with electricity. Only then can be confident that none of the tenants will give a random current to the apartment.

To remove the switch, we need the following tools:

• Portable light source
• Voltage Indicator Screwdriver
• Flat and crucible screwdriver

Flat screwdriver We will need to disconnect the keys. It is necessary to do it carefully, so as not to scratch the keys and the frame, and also do not break them. The point is installed between the frame and the key, on any side. Next, you need to make a slight force using a screwdriver as a lever sufficient to move the key from your place. The remaining keys with their presence are removed much easier, without using screwdrivers.

Now check if there is no voltage. Here we will need an indicator screwdriver that we apply to each of the contacts. Suitable to keys. It is recommended to install a flashlight or any other light source to see exactly what you do or touch. Therefore, it is better not to perform such works of newcomers with newcomers, it is very difficult to do without help.

After removing the keys, the wizard gets the ability to check the integrity of the contacts, as well as determine the voltage in them. This will allow you to answer the question, whether the switch was out of order and whether its complete replacement is required. If you need further dismantling, go to the next step of work.

How to remove the frame - the algorithm of action for beginners

Remove the switch from the wall may be required in cases where it is necessary to completely replace the device, as well as make a detailed inspection of the equipment. In this case, it is not possible to restrict ourselves to the keys alone, you need to shoot an additional frame. Fortunately, this process is also no particular complexity, the main thing is to act in accordance with the instructions and safety equipment.

A set of tools We need the same as for working with keys. More often the switch itself is fixed by several screws, to unscrew the cross screwdriver. By unscrewing the screws, you can remove the frame. It is very fragile and thin, so actions are performed as carefully. Again, a flat screwdriver is required to pose a frame, then pull the fingers on yourself. If everything is done correctly, the fixing frame will easily go away, after which you will only have to get the light switch.

Socket with switch - dismantling features of this device

Universal structures are very popular, including a socket and switch made in a single case. Such devices are sufficiently convenient during operation, because it appears and connect lighting, and power out the outlet from one incoming line. The disadvantage is obvious - in the event of a breakdown of one of the elements, you will need to remove the wall outlet along with the switch, regardless of the source of the problems. It is not worth worrying, because this operation is performed very quickly.

Armed with a flat screwdriver, remove the keys as described above. Under the keys there are screws, removed by which with a cruciform screwdriver. This is not the only fastener element - there are no screws on the outlet, which will also need to unsubscribe to dismantle the entire case. By unscrewing all the screws, it remains only to carefully pull the device's body for yourself so that it moves away from his place. To help yourself, you can use a flat screwdriver again, carefully approaching the housing.

In cases where the source of lighting problems is a switch, it will be necessary to replace it with a new one. Going to the store construction machineryBe sure to take with you the old switch. This will allow you to be sure that new model It is suitable for the existing connector. By the way, if there was a key tool, it does not mean to buy only the same equipment. So, the touch switch is perfect for a touch switch, or a switch with a smooth adjustment of light.

Connecting a new switch is performed in the order completely opposite to the dismantling of the old one. The apartment, naturally, is completely dealers, after which the device itself is disposed. Next, the wires are connected, it is necessary to do this in the same places where they were connected on the old switch. After that, the block is installed in the subtle opening, fixable by four screws.

It remains only to fix the decorative frame and the keys. On this work can be considered completely performed. Turning on the switch in the distribution panel, we make sure everything works with a bang.

On the walls there may be a need to take a temporary outlet. And what if you decide to replace the outlet? In these and other cases, it is important to know how to remove the wall outlet correctly. After all, with an inaccurate dismantling you can. In this article, we will consider with you a socket device, as well as instructions on how to remove it correctly.

Knowing the outlet device, it is easier to cope with its dismantling and, accordingly, mounting. The socket assembly consists of a contact pad, peavering and a decorative lid, which is fixed with the screw. As for the shoe itself, it has the following parts:

• Fasteners. They can be movable sawing screws or solid motionless.
• Contact. Zero and phase. There is also a grounding, it is usually located separately.
• Terminals for connecting wire.

Note! Pads that are equipped with rolling legs, mocked more difficult to penetrate. but this design Allows you to adjust the position by the slope and altitude exactly on the wall. When buying, pay attention to the paws, there must be two teeth on them. The shoe having one tooth on the foot quickly looses.

As for terminals, they can be fixed to the contacts of the screw or to be with the contacts. If we talk about reliability, the last option is better. Also terminals may have different species, for example, screw or "rams". IN last variant The bare ends of the wire are simply inserted, it is also much more reliable.

Varieties of sockets

There is a wide variety of outlets. For example, they can be single or combined under one lid with switch. There may also be a socket in one module two, three and four. Accordingly, all sockets are mounted on the wall in one row and are combined with one module, as well as a decorative lid. Moreover, the modular socket can be alarm sockets, for example:

• The Internet.
• Television.
• Telephone.
• Timer and so on.

For such sockets, special boxes are required, which should also be carried out according to all requirements.

Note! In the process of mounting and laying the cable in the boxes, they should not intersect, and also touch.

How to remove the outlet

So considering the main specifications Sockets and their types can be started to the main way to remove the outlet from the wall. To do this, you will need:

• little screwdriver with a plastic handle,
• insulating tape,
• latex gloves,
• tester.

Here is a step-by-step instruction:

1. First of all, it is necessary to de-energize the apartment. It should be checked several times that the electrician is actually de-energized. To do this, you can use the tester.
2. Depending on the type of socket, dismantling the decorative lid. It can be fixed with screws or latches. In domestic outlets used screw.
3. Then unscrew the fasteners of the socket. If the paws are movable, then when unscrewing the screw, it will become accessible to withdrawal.
4. Gently should be pulled out the entire design of the outlet and see how enshrined