Everyone who has come to use barrels or large canices, know how to blame the liquid from them, especially if they are filled to the top. To simplify this task, the container can be improved, namely, to embed a drain crane into it. Below we will consider in detail how in a barrel to cut the faucet so that the container does not lose their tightness.

General

The drain valve is a very convenient device, since thanks to it, the container does not need to turn over or lift. In addition, the drain is accomplished neatly, without spraying the fluid, which also happens in some cases extremely important.

Crane in a barrel is a relatively simple procedure that can be done for everyone homemade Master. The only one should note that this process depends largely on the material from which the container was made.

Therefore, below we look at how to cut a crane in iron barrel And plastic container.

Badge plum

In a metal barrel

Place the drain should be as low as possible. However, it is not necessary to do it in the bottom, since a similar insert will significantly reduce the functionality of the design and will require a special pedestal for it.

For the inserts, the following materials will be needed:

The price of all these materials is not high, therefore the cost of this operation is minimal.

Note!
Before proceeding to the cutting of the drain, it should be cleaned interior surface Capacities from dirt and rust.

So, the instructions for performing this work looks like this:

• Before cutting the crane in metallic barrel, you need to outline the location of the plum. To do this, you can use the usual circulation.
• Then in the specified location you need to drill a hole. If necessary, the hole can be expanded with a circular file. The main thing is that it corresponds to the diameter of the CU.
• Next, from the side of the short carving of the CONSTANCE should turn the lock nut, after which it is inserted outside in the prepared hole.
• After that, from the inside you need to push the second countertilization.
• On the free part of the thread should be hounded with fum-ribbon and apply abundantly.
• After that, you need to carefully tighten the connection.. It is necessary to make it with an effort to make a wall deformation at the squeezing place.
• Now it remains only to fasten to a Sgon. shut-off reinforcement and check system performance.

On this, the process of plum cuts is completed with their own hands.

In plastic barrel

Now consider how to cut the crane in plastic barrel. It is best to fulfill this procedure using a thermopystole and thermoclause.

If there is no such tool, then the tap in the plastic barrel can be performed using a threaded connection. The only thing in this case should take care of the sealing of the joint.

This is done as follows:

• As in the previous case, before embeding a crane in a plastic barrel, you need to outline and drill a hole. If the plastic is soft, the hole can be cut with scissors or a sharp knife.
• Then it is necessary to prepare a mortise faucet for a plastic barrel. For this, the threads need to install a large metal washer and waterproofing rubber gasket.

• Next, it is necessary to apply the sealant to the gasket and the puck, as shown in the photo.
• After that, the input nozzle of the device should be inserted into the hole and on the other hand also put on the threads with a rubber gasket and a washer, processing the mix of the sealant.
• At the end of work from the inside on the thread you need to screw the nut.

Often, the container has a narrow neck, as a result of which it is impossible to screw the nut from the inside. In this case, you will need a fitting with a flange on one side.

Work in this case is performed in this order:

• First of all, you need to perform a hole in the container in the diameter of the fitting.
• Then the fitting should be fixed on the metal wire, which will push it into the hole from the inside the canisters through the neck and then pull the wire. To do this, the limiter can be tied to the wire on one side.

In the photo - fitting with flange

• Before inserting the fitting into the hole, the place of fitting the flange to the wall of the tank must be lubricated with the sealant, you can also use a rubber gasket.
• Next, the wire is dyed through the neck into the hole and thus the fitting is pulled out. Holding it to the wire, on the thread from the outside, you should turn the lock nut, after setting the rubber gasket and finishing the place of the joint of the sealant.
• At the end of work on the fitting it is necessary to turn the shut-off valves.

Tip!
To make the canister more comfortable, you can cut into it the second neck, from the opposite side relative to the first one.
In this case, the drain of water will be carried out evenly.

This is completed on this process.

Output

The tap in the container does not require large costs of finance and strength, but it makes it much more convenient to use. The only one to perform this operation should be accurate, adhering to the above recommendations in order not to spoil the product.

From the video in this article you can emphasize some additional information According to the topic indicated.

Many dackets and motorists have repeatedly come across the use of large canisters or barrels. Therefore, they certainly know how it is inconvenient to contact them, merge or overflow liquid, especially if they are filled to the edges. Solve this problem will help the installation of a drain crane. In this article we give useful recommendationsRegarding how to cut a crane into a metal barrel or plastic canister.

Why is it worth using a drain crane?

Drain valve - incredible convenient deviceAfter all, thanks to him, it is possible to drain the liquid without any problems, it does not need to raise the container or turn over. The process itself is accurately carried out, the liquid is not sprayed that in most cases it is very important.

Title the procedure of the tap of the crane in the barrel is impossible, but with it any home master will be able to cope with it. But certainly it is worth noting that the material from which the container is made here is tremendous. That is why below we give examples, how to cut the drain faucet into the plastic and iron barrel. Try to follow the recommendations described, since it depends largely its operational quality and service life.

How to cut the crane into a metal barrel?

Before you cut a crane into a metal barrel, mark the place of placement, better - so that it is located as low as possible. The main thing is not to overdo it, do not do it on the bottom, since a similar version of the insertion strongly reduces the functional properties of the structure and requires the installation of a special pedestal.

Prepare the following materials for work:

1. Sign is a pipe with carvings.
2. Crane. For such purposes, as a rule, use a shut-off ball fittings. It is important that its nozzle has internal pipe threadSo that it is convenient to wind the crane for a Sgon.
3. Lock nut. They will be useful for fixing the camp.
4. Sealant and fum-tape. They are needed to seal the compounds.

Important! All these materials are inexpensive, so this operation will not hurt much family budget. Before the beginning of the insertion, it is necessary to clean the inner surface of the barrel from rust and dirt.

Perform the crank the crane in this scheme:

• Do not forget to outline the location of the plum. Take advantage of this as the most ordinary circulation.
• Then drill a hole at the specified point.

Important! If necessary, it is possible to expand it slightly with a round file so that it coincides with the cigrous diameter.

• Screw the lock nut from the short thread of the CUT. Insert it into the prepared hole outside.
• From the inside, push the second lock nut.
• Mix on the free part of the FUM tape thread, lubricate this place with silicone sealant for pipes.
• Tighten the connection thoroughly. Create as much effort as possible so that the walls are slightly deformed at the scene.
• Screw the lock fittings to the Sgon, check the system performance.

How do you equip a plastic barrel with your own hands?

Now it is time to consider how to cut a crane into a plastic barrel.

Important! This procedure It is recommended to perform with a special pistol and thermoplastic glue. If you do not have such tools at hand, you can perform insert through a threaded connection. Only then will have to take care of the proper sealing of the joint.

You must do the following:

• As in the previous case, check out and drill a hole on a plastic barrel for taps.

Important! You can use the sharp knife or scissors if the plastic is soft enough.

• Prepare a mortise crane. From the thread side, install a large metal washer and rubber gasket for waterproofing.
• Apply the sealant to the washer and gasket with a thick layer.
• Insert the inlet nozzle into the hole, put on the other side on the thread washer and rubber gasket. All joints are treated with a sealant.
• Screw the nut on the thread from the inside.

As a rule, similar containers have a narrow neck, so problems arise with screwing the nut from the inside. If you caught just such a barrel, then use the fitting, equipped with the flange. Perform all actions in the following order:

• According to the diameter of the fitting, make a hole in the container.
• Secure the fitting on the metal wire so that it is more convenient to push it into the prepared hole from the inside the canisters directly through the neck, then pull the wire.

Important! Do not forget to bind to the wire on one side limiter.

• Before placing the fitting in the hole, lubricate the flange location to the wall of the barrel.
• Slide the wire through the neck into the hole, pull out the outset. At the same time, try to hold it with wire. Then turn on the thread from the outdoor side of the locknut, pre-put on it rubber gasket and processing the joint sealant.
• Screw the shut-off fittings for the fitting.

Important! So that your canister is more comfortable, cut an extra neck into it from the opposite side. This will make it possible to drain the water evenly.

Rooms autonomous water supply on the cottage plot You can do using a conventional metal barrel as a water tank. Modern water fittings allows this to do this without the presence of special skills using the usual household tools.

What is needed for this?

The simplicity of water supply initially focuses on minor costs during its equipment. Separate elements The future system can be found directly in the site. The water storage capacity for the cottage is constantly and is almost a matter of worship. That is understandable due to the constant lack of water on watering and the need to comply with the elementary rules of hygiene.

Two or three, albeit rusty, and possibly placed in places, metal barrels will always be found in such research. Minor holes are easy to close, rust remove and, after painting, nothing will remind of her inglorious days as a primitive stand when collecting apples, countertops under the basin or the place of storage of something unnecessary, but extremely protected.

Rubber hose, pieces of pipes, paint, sealant, rubber pieces - quite expected remuneration for searching and replenishing the resource of the future water supply. All discovered must be formed together to determine the purchase of the necessary accessories:

• crane. The inlet nozzle must have an internal thread, and the outgoing can be made in the form of a fitting if the rubber hose is connected to it, the transition under metal plastic pipeor threaded connection under the flexible hose;
• sign. Threading should have coordination with the crane;
• two locknuts. With their help, the clamp of the camp on the body of the barrel is carried out;
• sealants. For a threaded connection, it can be a fum-tape or flax.

At the next stage, you should choose a tool. The minimum set includes:

• drill and drill on metal. The clamping cartridge of the household tool holds the shank with a maximum diameter of 10-13 mm, which is clearly not enough for the hole under the crane. Therefore, the drilling is made through the required circumference. Enough diameter of holes about 6mm;
• hammer and chisel. Without an application of great effort, neatly, jumpers are rented from the hole to the hole using the specified tool, and it is formed, albeit not the round, the hole of the desired diameter;
• file. We are needed to align the edges of the hole. Most comfortable round, going to the cone, file big diameter. In this case, you can achieve an ideally level circle;
• keys for tightening threaded connections. The size depends on the applied accessories. Most often it is the key to 22. The adjustable tool will save from the need to guess.

How to cut a crane into a metal barrel?

The barrel is cleaned from dirt and rust. When detecting holes with inner Sealant is applied. Even ordinary plasticine is well suited for this, with the reservation, that it is necessary to apply it after painting the tank.

The inner cavity is better painted with sudic. The peculiarity of this substance is that the elements included in it create a solid connection with iron at the intermolecular level. This gives a guarantee that during the year corrosion will not appear and will not affect water. Outside, the barrel is painted on the taste of the owners. If you want water to be better heated under the rays of the sun, it is advisable to use dark color solutions.

Place a crane on a barrel should be as low as possible. No need to do it on the bottom. In this case, the functionality of the container will decrease sharply, as the construction of a special pedestal will be required. You can draw the circle with a conventional school cycling. If not, it is necessary to draw an inlet pipe on a sheet of paper, cutting the circle formed and attach to the drilling site.

The metal at the barrels is soft and easy to handle. Difficulties with the formation of the opening does not occur. The main operations are the installation of the CU. It requires a clear sequence of actions:

• from the side of the short carving of the coction, the knocking is screwed, after which it is inserted outside to the prepared hole;
• next, it should be fixed from the inside the second lock nut;
• to impose a fum-tape either flax on the free part of the thread, to abundantly apply the sealant and tighten the connection. A significant effort is required to raise the strain of the barrel surface at the squeezing point.

After that, it remains to fasten the crane, install a barrel in right place And, after connecting hoses and pipelines, give a symbolic fountain in honor of the completion of work.

Everyone who has come to use barrels or enormous cannors know how to uncomfortable liquid from them, especially if they are filled to top. In order to simplify this task, the container can be improved, in particular, to cut into it a drain crane. Below we will consider in detail how to cut the crane in the barrel, so that the container, along with it, did not lose their tightness.

Non-specialized information

The drain valve is a very ergonomic device, because thanks to it, the container does not need to turn over or raise. In addition, the drain is carried out carefully, without spraying the fluid, which also happens in some cases very fundamentally important.

The cutting of the crane in the barrel is a relatively simple procedure, which can be done at each home master. The only one is to be sent to emphasize that this process is highly dependent on the material from which the capacity was made.

Based on this below, we will look at how to cut a crane into a metal barrel and plastic container.

Badge plum

In the iron barrel

Place the plums are directed as possible below. But, do not do it in the bottom, since a similar cutting will significantly reduce the functionality of the design and will require a special pedestal for it.

The following materials will be useful for the insertion:

The price of all these materials is not high, based on this cost of this operation is minimal.

Note! Before proceeding with the cutting of the drain, it is directed to clean the inner surface of the tank from dirt and rust.

So, the instructions for executing this work looks like this:

• Before cutting a crane into an iron barrel, you need to outline the place of plum. To do this, it is possible to use a simple circulation.
• After that, in the specified location you need to drill a hole. If necessary, the hole can be enlarged with a round file. The main thing that it corresponded to the diameter of the cooler.
• Then, from the side of the small carving of the CONSTANCE, direct the lock nutAfter completing what it is inserted outside to the prepared hole.
• Then from the inside it is necessary to push the second lock nut.
• On the free part, the threads are sent to wind the fum-ribbon and wear abundantly silicone sealant For pipes.
• Then you need to whispenly tighten the connection. It is necessary to do this with an effort app, so that the wall deformation happened at the squeezing site.
• Now it remains only to fasten the locking reinforcement and check the system performance..

On this process of the cut-off of the drain of their own hands is completed.

In plastic barrel

Now consider how to cut the crane into a plastic barrel. Optimal to perform this procedure using a thermopystole and a thermoclaus.

In the event that there is no similar tool, the tap in the plastic barrel can also be performed using a threaded connection. The only thing in this case should take care of the sealing of the joint.

This is done as follows:

• As in the past case, before you embed a crane into a plastic barrel, you need to outline and drill a hole. If the plastic is soft, the hole can be cut out with scissors or a sharp knife.
• After that, you need to prepare a mortise faucet for a plastic barrel. To do this, from the thread, it is necessary to establish a huge iron washer and waterproofing rubber gasket.

• Then it is necessary to apply the sealant to the gasket and the puck, as demonstrated in the photo.
• Then the input nozzle of the device must be inserted into the hole and otherwise wear the rubber gasket and the washer on the thread, using the sealant's joint.
• In the end of work from the inside on the thread, you must turn the nut.

Typically, the container has a narrow neck, as a result of reaching the nut from the inside is unrealistic. Under such conditions, a fitting that owns the flange on one side.

Work under such conditions is performed in this order:

• First of all, it is necessary to perform a hole in the container in the diameter of the fitting.
• After that, the fitting should be fixed on the iron wire, which will be allowed to push it into the hole from the inside the canisters through the neck and then pull out the wire. To do this, to the wire on the one hand it is possible to bind the limiter.

• Before inserting the fitting into the hole, the place of fitting the flange to the wall of the tank must be lubricated with the sealant, but it is possible to use a rubber gasket.
• Then the wire is squocated through the neck into the hole and so the fitting is pulled out. Holding it to the wire, on the thread from the outdoor side to turn the lock nut, after setting the rubber gasket and processing the place of the joint of the sealant.
• In the end of work on the fitting you need to turn the locking fittings.

Tip! In order to make the canister more ergonomic, it is possible to cut into it the second neck, on the opposite side relative to the first. Under such conditions, the drain of water will be uniformly.

On this, the routing process is completed.

Output

The tap in the container does not require the enormous costs of finance and forces, but along with this makes it much more ergonomic in use. The only thing to make this operation is guided carefully, adhering to the above recommendations, in order not to break the product.

From the video in this article it is possible to emphasize some additional data on the topic designated.