Therm-x2 technology it is used in all profile, smooth, hygienic and multi-panel radiators Kermi 12, 20, 22, 30 and 33 types. And it sets completely new standards in the steel segment. panel radiators because it has a number of unique advantages. With the release of Therm-x2 radiators, Kermi is prioritizing the optimization and energy efficiency of the heat transfer process: new technologies reduce the heating time of the radiator by up to 25%, the radiation intensity is increased by up to 100%, while energy savings reach 11%. What is the difference between Kermi steel radiators and why are they energy efficient?

Why Energy Saving Heatsink Kermi Therm-x2?

The success of Kermi energy-saving radiators is based on the latest patented Therm-x2 principle, which is based on the sequential flow of heating medium through the radiator panels. If in panel radiators according to the previous technology all panels were heated at the same time, then according to the Therm-x2 principles, the coolant from the supply pipe first enters the front panel. In the mode of partial load of the heating system, for example, in the off-season, the power of the front panel is usually sufficient to warm the room, and the rear panel serves only as a heat shield. And only when a lot of power is required, the back panel begins to give off heat in full force and, thanks to its convection properties, contributes to the rapid heating of the room. Thus, due to the greater temperature difference between the supply and return pipelines, the energy efficiency of the radiator is increased and losses during heat distribution and generation are reduced.

For the most efficient use of energy. And maximum comfort.

As independent qualified studies have shown, as a result of the energy advantages of heat transfer with the sequential flow of the coolant in steel panel radiators of heating Kermi Therm-x2, unlike other panel radiators, not only significant energy savings, but also maximum thermal comfort can be achieved. Our sense of comfort in a room is highly dependent on the radiation intensity of the radiator. Even when the thermometer shows the required temperature, but the radiator practically does not emit heat, there is no minimal feeling of comfort, the room is subjectively perceived as cold. With Kermi radiators, the situation looks different. In him average temperature the front panel is significantly higher, thanks to which in normal use the radiation intensity is increased by almost 100%, which guarantees a feeling of maximum comfort at all times.

The full energy efficiency potential of a Kermi heating system with Therm-x2 technology can only be fully realized if the heat transfer process is involved. In energy-saving Kermi radiators, the high efficiency of thermal energy sources is maintained at all stages of heat transfer. It is worth noting that using the innovative Therm-x2 technology, the total energy savings in heat transfer can reach up to 11%! If you think about the fact that 75% of all energy consumed in the economy comes from heating, they will open huge opportunities cost savings.

Compared to traditional panel radiators, the use of therm-x2 energy-saving radiators allows annual savings of over 6,000 kilowatt-hours in older buildings. They could bake 6000 pies, shave 15600 times with an electric razor, wash 6270 times, operate the refrigerator for 42 years. If all 14.5 million single and semi-detached houses were to switch to Kermi Therm-x2 technology, over 9 billion liters of fuel oil could be saved per year! And CO2 emissions are about 24 million tons annually. This high potential for energy savings makes Kermi panel radiators the starting point in the development of new heating systems that meet the high demands of tomorrow. For the good of man and nature!

Kermi - Best Energy Saving Radiators of 2012

Since its inception innovative technology Therm-x2 calls great interest both for specialists and for ordinary consumers. The success story of Kermi flat panel radiators goes on and on: the prestigious PLUS X AWARD jury awarded the entire product line for outstanding performance with the PLUS X AWARD 2012 and was also recognized as " Best product of the year 2012 "for functionality, environmental friendliness and quality. Along with impressive results in energy saving, the judges also noted the versatility of the family Kermi Therm-x2. Either heat pumps, solar collectors or technology for maximum utilization of the calorific value of fuel - therm-x2 energy-saving radiators right choice in every case. Especially when it comes to maximum thermal comfort combined with the best efficiency. Radiators are connected to any heat source and, even during heat transfer, save a significant part of the energy consumed. This makes Therm-x2 a very strong "Kermi Wärmesystems x-optimized" component.

Energy savings of 11% arise due to the fact that only the front part works for a while. Heater for 2 kW - two panels of one kilowatt each, - the radiator gives not 2 kilowatts, but 1. The rear part warms up after 15-20 minutes. During this period of time, discomfort is felt, but the same 11 percent of energy savings are obtained.

There are defective systems in which there is no balancing, and an insufficient amount of moving fluid passes through the device. On the thermograms, the heating of the panels is observed only in the upper part, which indicates a lack of coolant. If there is a lack of it on both panels, then the streams are distributed in such a way that there is enough for at least one. But this method cannot be used. By installing a radiator with local constrictions, we further increase the hydraulics of the system, which leads to a shortage of coolant and one panel. There is a possibility that if there is some margin for balancing, then the principle of therm X2, in some way, will be implemented and will give us something. If the systems are clamped and there is not enough fluid, then there is nothing to clamp, and again we come to an increase in the load. Therefore, the implementation of this technology in well-tuned, correctly balanced and assembled systems is impossible, because this technique works only for the first 10-20 minutes after the thermal head has opened the radiator.

If you want to buy Kermi radiators with bottom connection, you cannot refuse to use X2, since it is already built into them.

Profile compact radiators Kermi Therm X2 Profil K are made of sheet steel and have a uniform two-layer lacquer coating that does not emit harmful substances for the environment during heating mode. The surface is degreased, treated with iron phosphate, primed with cathodic dipping and powder spraying in accordance with DIN 55 900-FWA. Standard: Kermi white (RAL 9016). Colored varnishing is available on request. 4 pads (for mounting a radiator longer than 1800 mm - 6 pads), including a system-appropriate mounting kit with brackets with holes, installed plugs and air vents. All radiators are leak tested and ready for installation. Packed in cardboard and covered with foil. Protective packaging for installation.

The radiator is factory equipped for use in two-pipe system, with bypass threaded connection(accessory), also suitable for use in one-pipe systems (For single pipe system- valve setting 8). The quality control system is certified according to DIN EN ISO 9001: 2000. The design complies with the previous directives of the former BAGUV (Union of policyholders at the expense of the federal budget). Certification acc. with GOST.

• Connection: 4 x G 1/2 ”female thread
• Working pressure: max. 10 bar
• Wednesday: hot water up to 110 ° С

Kermi Therm X2 radiators are ideally compatible with all heating systems and thus an excellent answer to all the heating technology demands of tomorrow. The patented X2 technology, with an increased radiation intensity of up to 100%, takes care of best use Efficiency energy efficient sources heat. Optimum heat dissipation into the room and high level thermal comfort even at low system temperatures. Thus, Therm X2 radiators are ideally suited to all combinations: with heat pumps, technology max. use of the heat of combustion of fuel, solar collectors, as an adequate, future-proof form of heat transfer already in our time, tuned to maximum efficiency use of energy. They are also the best alternative for refurbishing a heating system without underfloor heating.

Therm X2 models have a higher energy efficiency than flat radiators.

New radiator markings:

The model range of valve radiators FKV, PKV, PHV types 12, 22, 33 has been transferred to the new classification. New radiator markings will look like this:

Old designation - Profil-V FKV 220510
New designation - Therm X2 Profil-V FTV 22050100, article: FTV 22 050 100 1 R 2K

Full description: Kermi Therm X2 Profil-V Type 22 BH 500x100x1000 mm
1 - designation white Ral 9016 (when ordering other colors, simply write RAL)
R - standard connection on the right (L - connection on the left / no extra charge / on order)