How to start a chainsaw

The question of how to start a chainsaw can be divided into two parts:

1. Factory by annotation
2. What to do if you can't start

The information from the first part will be useful to those who have lost the annotation, or those who have little information about the annotation.

The second part will tell you what to do if you did everything correctly according to the annotation, but the chainsaw still does not start. It will also be useful for those who have a poorly started chainsaw.

1.We start the chainsaw according to the instructions

For different chainsaws, starting can be done in different ways. Let's take a look at two of the more popular mechanisms that are used to start a chainsaw that are available today. Let's take the Stihl MS 180 and Echo CS-352ES chainsaws as an example. To properly start a chainsaw calm, husqvarna or another brand, you must first read the instructions and follow its points. If you have a different brand of chainsaw, then just try to start by analogy, because most likely you have the same or a similar mechanism.

Before starting a description of the starting process, I want to see that for some chainsaws it is written in the annotation that before starting the chainsaw, it is necessary to turn on the critical stop brake. They say it's safer. But with a fixed brake, it is more difficult to start the chainsaw, therefore it is better to unlock it. If you do everything according to reason, then the chainsaw will not do anything for you during start-up. If you are afraid that without fixing the brake the chainsaw, when you try to start it, will be able to harm you, then it’s better then generally not to take up this tool.

So let's start with the Stihl MS 180.

• The first thing to do before starting this chainsaw is to move the choke adjustment lever to the lower position (Fig. 1). Please note that this lever moves to the very bottom on the chainsaw only if the gas button is pressed. Therefore, we hold down the gas button and move the lever down. Thus, we close the choke in the carburetor and fix the gas in the pressed position at the chainsaw.

Now we will analyze the 2nd 2nd mechanism that allows you to start the chainsaw.

• First, before trying to start, turn on the ignition by moving the switch or the switch of the chainsaw to the appropriate position (Fig. 5).

How to properly start your Husqvarna chainsaw

How to do it right to run Chainsaw Husqvarna... How to start a chainsaw - a couple of the most popular. Recommendations for starting a chainsaw. Buy on the website www.

Chainsaw Husqvarna Husqvarna 236 video review how to start a chainsaw

Chainsaw Husqvarna(Husqvarna) 236 - performance overview, first cold start. We are on Vkontakte:.

Rice. 5

2.Why won't the chainsaw start?

If you did everything according to the instructions, and the chainsaw does not start, then something is wrong with it. This may be due to several of the most common reasons: there is no spark; no fuel is supplied; the air filter is clogged. So, below we propose a procedure that will help identify the reason why the chainsaw does not start.

Procedure if your chainsaw does not start

Read the same

The first thing I would like to note, if your chainsaw does not start, do not turn any screws on the carburetor. You need to start the saw, you need to prepare the correct mixture of the saw husqvarna 142. Sometimes. If you are not an expert, you will still not be able to set up something on your own and you will not be able to start the chainsaw.

Follow the next steps required to start the chainsaw in the order shown, starting with the next number only if the previous one did not help.

1. For a start, try just leaving the chainsaw alone for 5-10 minutes. Perhaps during the start-up, a candle flooded in her - it happens. Then try starting again according to the instructions.
2. Remove the housing cover on the chainsaw, remove the air filter and try to start without it. If the filter is dirty, wash it in soapy water and dry it or replace it with a new one.
3. Unscrew the spark plug from the chainsaw. Check for a spark. Husqvarna 236 chainsaw malfunctions. Recently I bought a husqvarna 236 chainsaw, at the moment it is not clear to me how to run it in correctly. If there is no spark, then try putting in a new candle. If the spark still does not appear, then this means that the ignition unit is damaged and the saw needs to be carried for repair. True, visual observation of a spark does not mean that the ignition unit is working properly. If there is a spark, and the chainsaw did not work, do the following steps on the list.
4. If there is a spark, but the plug is wet, then turn the chainsaw over to drain excess gas from the cylinder if it has accumulated there. Pull the starter 10-15 times without a spark plug to ventilate the combustion chamber. 3.1 how to breed gasoline for a chainsaw calm 180? 3.2 how to start a chainsaw calm 180?. Ignite the candle and screw it back, or better, change it to a new one, if available. Try starting again according to the instructions.
5. If the candle is dry, then draw one or two cubes of gasoline mixture into the syringe and pour it into the cylinder. Try to start the chainsaw - perhaps a small speck has got into the carburetor, which prevents the fuel from entering the combustion chamber. It is quite possible that this speck will be pulled out by the stream formed after starting the chainsaw by adding fuel directly to the cylinder.
6. Unscrew the muffler and remove it, being careful not to spoil the gasket between the muffler and the engine. how to start how to properly clean a Chinese chainsaw. Try to start without muffler and air filter. With the muffler removed from the chainsaw, you can inspect the piston from the inside. Why do you need to run in a chainsaw? How to properly run in a new or repaired chainsaw calm, husqvarna and others. If there are burrs or scuffs on the walls of the cylinder or the piston, or the ring on the piston is jammed with burrs, then you will have to be very upset, as this means that the piston is damaged or worn out. This usually happens when oil is not added to the fuel mixture. With such a malfunction, you will have to contact the service, and perhaps think about buying a new chainsaw, since replacing a piston one is a rather expensive operation.

Read the same

What kind of gasoline should be poured into the chainsaw Hello! I am glad to create you again, dear readers and subscribers of Andrey Noak's Blog. Everyone who has a chainsaw at home already knows exactly what kind of gasoline and how to fill it. But to those who only wish to purchase such a unit for themselves, the article will seem amusing. Chainsaw - ...

Malfunctions of the Stihl MS 180 chainsaw and their elimination

Chainsaw in operation Calm MS 180. How to properly start a chainsaw calm 180. Problem in the future. Before conservation for the winter, on the advice of mechanics, I dripped 4 drops of engine oil (calm) into the hole of the candle. twirled the candle. At the moment, I was going to go to the dacha, I decided to take a look at the saw. How to start a chainsaw in the most that after a long downtime of the saw, start it with. I pulled the starter, but it does not turn! He turned out the candle, it was in oil, put it back on. same. He turned it out, turned the starter without a candle - everything is completely spinning. Spinned back - the starter does not turn. What could be?

Rinse the saw with clean, undiluted gasoline, pour straight through the plug hole and slowly turn the starter. Later, drain the fuel and use the newest. After all these manipulations, dry the saw and the candle and only then try to start it. Once you have learned to preserve, then learn and re-preserve, and not just yanked and drove off.

Tell me, what is the reason for the starter to jam? The Stihl 180 chain saw is brand new.

You can't make out, you don't know. Maybe the starting cord does not fit well, or maybe somewhere the ebb tide interferes. Shtilev starters are quite reliable and durable. There are no diseases of a constructive plan, in the main either mud or saturated operation. Once the chainsaw is brand new, bring it to the service under warranty, it will be repaired.

I'm here at my own chain chainsaw Stihl MS 180 saw one feature: when the tank runs out of gasoline, the rpm idle move increase and the chain starts spinning even when the trigger is released. When you press the gas, the chainsaw stalls. This continues for a couple of 10 seconds, later the chain saw stops. On automobiles, I did not observe such a phenomenon, so that when there was a shortage of fuel in the carburetor, the engine speed would increase. Why it happens?

This is a common occurrence for two-stroke engines. With a decrease in the supply of gasoline to the carburetor, the consistency is depleted. Consequently. increase in revs, deterioration of acceleration. This is accompanied by short-term overheating of the CPG. The engine will not disable it, but it will not add health. Avoid running out of fuel from the tank to the end.

There is a Stihl MS180 chainsaw, used in the summer season for the preparation of firewood. In the near future, the reaction of the chain when you press the gas began to disappear, the chain does not turn at all, or in jerks. to cut is unrealistic. How to start a husqvarna chainsaw. What could be the breakdown?

For a completely new chain and sprocket, the tension should be exactly according to the annotation. so that the lower branch does not sag. and the upper fingers could be removed to the height of the driving link. Then the chain will move fairly freely on the bus. But, the gradual wear of the teeth of the sprocket decreases its pitch. And the gradual stretching of the chain increases its step. and the time comes when the steps of the same sprockets and chains no longer coincide to such an extent that the recommended tension already causes a difficult movement of the chain. In this case, we recommend reducing the tension a little. Right before the appearance of a certain sag of the lower branch. By the way, for the same reason, it is recommended to use a pair or even three chains on one sprocket. In this case, the wear is moderate and there will be no accelerated wear of the newest chain on an old, partly worn out sprocket.

Chainsaw Calm 180 after starting, when you press the gas, "chokes" and if you start sawing, it stalls. But if you torment with gas for 30-40 seconds it starts working normally. produced 3 liters of gasoline, filter clean, oil from a dealer.

If it started not so long ago, then, most likely, something got into the carburetor with bad fuel. It needs to be cleaned.

I would like to purchase this unit. What should you pay attention to when examining?

Not to mention the engine itself, since it is better to diagnose it in the service, you can look at the rest and get a lot of information. Significant mileage will be evidenced by: Dangling latch of the top cover. (Should lock tightly and not rotate from vibration). A brand new sprocket on a battered chainsaw. At removed cover movement of the motor relative to the body. Sheared chain catcher and chain damage on the sprocket cover. You can also take a close look at the carburetor from the left side along the way. where the wire rod fits into the choke axle arm. With a slightly worked chain saw, it will be flat, oblong. The longer the saw has worked, the more this hole will be worked out. From time to time it is rubbed through. Under no circumstances should you take a saw that has at least a small free play of the right end of the crankshaft relative to the motor. This is a sign of imminent renovation.

How many seconds should the engine run chainsaw Calm ms 180 at idle before jamming it?

Let it work for about 20-30 seconds and then muffle. Their cold start a review of the chainsaw ms 180. How to start a chainsaw "calm ms 180. More. there's no point.

Idling began to disappear, at first I did not understand what was the matter, and later I remembered that I needed to add a lot idle move I added on a hot motor it seemed to work. I come to the dacha in a week, I need to cut a couple of logs, start a saw and at first on a cool motor the chain spins later everything goes away, I stood for about 10 minutes I start everything normally only on a cool motor. This is fine?

If the chain turns, it means that the speed is too high. It should be understood that a normally adjusted and serviceable motor is completely likely to have a slightly overestimated idle speed immediately after starting before warming up. And he can be promoted decently. before the chain rotates. With the engine warming up, the idle speed is gradually lowered. For this reason, it is recommended to adjust the idle speed only when the engine is warm.

Is it possible to put a clutch drum with a removable ring on the Stihl MS 180 chainsaw ("modernization" of the drum is allowed), for example, from the 250th.

Read the same

Can. Everything fits perfectly. Just do not run over to, 325 ". It's hard for the motor. But you should mean a couple of aspects. How to start a husqvarna chainsaw. Nevsky method. On such a set (with a removable) the sprocket is a little larger in diameter and one tooth more. The speed of the chain will increase in proportion 6: 7, respectively, the load on the engine will increase. But practice has shown that this is not critical with normally sharpened chains. And the second, a completely new chain of 50 links on such an asterisk is difficult to put on. (In general, 51 links are recommended, but they occasionally happen.) The first time you have to suffer for her to stand on the sprocket and the tire.

I bought a Stihl 180 chainsaw. I poured oil, benzyl. Started up and gave it to work without load at idle speed. Burned a tank of gasoline, at times pressed the gas a little. For some reason, the oil for lubricating the chain did not come in, the oil hole remained dry. Or will it start flowing when the revolutions are higher and the chain spins longer?

How to properly start Calm 180 video

how to start Calm, start chainsaw Calm how true start the chainsaw Calm 180 1st video start

Stihl ms 180 videos

Wholesale and retail sales, service center, spare parts for products STIHL in the city of Krasnoyarsk in the Trade and Service

At the 180th calm, oil is supplied to the chain when the drive sprocket is spinning (in short, when the chain is spinning), but it is not recommended to run in at idle speed.

On the MS 180 chainsaw, after using 1 tank of fuel, I have more than half of the oil tank left. The groove of the bar and the base of the chain, which is in the groove, are in oil. How to start a chainsaw calm, husqvarna, try again to start the saw. But when checking, for some reason, oil does not sprinkle from the chain and the cutting teeth, in my opinion, remain dry when sawing. Wood deposits appear on the top of the cutting tooth. Oil enters, but leaves in the missing volume. Nothing could be hammered, the chainsaw was new, the hole was spotless. Is it a marriage of the manufacturer or is it supposed to be?

I will not argue about the consumption of chain oil in calm weather, but 2-3 tanks of fuel per oil tank is not it a lot? I have less than a quarter of a tank of oil left after running out of a tank of gasoline.

When I start the tool with the chain brake off, it cuts in from time to time just when I pull the starter handle. Is it okay?

This model is quite peculiar in its start-up, there is no decompressor and / or elastostart that compensate for the recoil, and, not looking at such a small piston size, it is still quite decent. Because of this, the saw must be started confidently, smoothly engaging the starter sharply and moderately pulling the starting cord, it is worth at some point to loosen the grip or slow down the speed of the broach as the recoil will remind you of a nasty feeling for yourself.

What is the difference between the Stihl MS 180 chain saw with a 30cm bar. and with a tire 35 cm? That is, the distance from the bumper to the tip of the bar?

So this value changes during use. The more the chain is stretched, the greater this distance. And the longer the bar, the greater the difference between the cutting lengths of the newest and the stretched chain can be. The difference in the length of the cut between the completely new and stretched chain will be about 1 cm in some places. The tire does not lengthen, but simply its tip moves further away from the saw body, otherwise the chain will not be tensioned. The limit for the growth of the length of the cut is determined precisely by the length of the tensioner screw and in which place of this screw the tensioner crack was located when the newest chain was installed. The further he was from the leading sprocket, the faster, with other equal criteria, the chain will become unusable due to excessive pulling. I am afraid that it will hardly be possible to buy a tire 1 cm longer than the standard one. How to start a calm, starting a chainsaw calm, how to start a chainsaw calm 180 first start video. Common tire lengths for household models. 12 ", 14", 16 "and 18" for 3/8 "x 1.3mm and 13" chains, 15 "and 18" for 0.325 "x 1.3mm chains.

Is it possible to keep the brake off when starting, or must the brake be on?

And this is already how it is more convenient and safer for you. There are three main launch options. on Idling, on "half gas" and "full throttle". In the first case, the chain is motionless after starting or may twitch a little. How to start a chainsaw, the question of how to start a chainsaw can be divided into two parts: starting by annotation what to do if it does not come out to start the information from the first part will be useful to those. In the 2nd and 3rd cases. the chain is moving. Setting the brake to the working position in the first start option is a waste of time. It is very unlikely that the idle speed at one moment and without circumstances would increase so that the chain would start moving. In the 2nd and 3rd cases, when starting with the brake activated, it is necessary to immediately release the brake after starting so as not to burn the clutch. When starting with the brake disengaged, after starting, it is necessary to press and release the throttle lever so that the saw engine goes into idle mode (in the 3rd case, at the moment of starting, this lever is already pressed, it only needs to be released).

It was necessary to work, the saw started up quickly, although it stood without work for 5 months, having cut everything that was needed, burned one tank of fuel, everything is fine. But I arrive in a week, there was no such puddle of oil under it before. What could it be?

Never been to those chainsaws. It usually rips the oil hose off the pump mount if you drop cool oil in the tank and put the saw in a warm place. The breather works only inward, the pump does not allow air to pass through, therefore the excess pressure has nowhere to go, well, it squeezes out the hose.

I bought the Shtil MC 180 C-BE chainsaw. I started by annotation. The consumer should be aware of not only how to start the "calm ms 180" chainsaw, but also about technical characteristics... Everything works fine, but very long and a lot of actions. I tried to start without a brake in position I, and also started up the first time. Tell me, is it possible to do this and how can it threaten?

It's better to start without a brake, the clutch will burn out quickly. Warm generally just starts up.

Now my instrument has not started. I unscrewed the candle, it is wet. I put it on the gas burner, tried it again later. Doesn't start in any way. 5 times I pulled out the candle, and it was always wet. What to do?

You try and not dry the candle. How to start a chainsaw video. I drenched them. I usually start it like this: I unscrew the candle, turn off the ignition. Jerks 10. 15 with a starter (if it is very flooded, put the muffler down and pull it). Later, dunu on the candle to knock down the excess fuel and screw it in. But I start it later, not from the lowest position, but from the second from the bottom (the air damper is open and the "starting" gas is given). Usually a jerk from the third. the fourth gets started. A little smoke and everything works. And from time to time it is too lazy to turn out the candle, so I give full throttle with my foot (on the ground, of course) and pull until it starts. In most cases, it will work. And if, after blowing out and drying the candles, you start again from the lower position, then you will fill it again. there is already a surplus of fuel, and we will also close the damper.

During operation, the stihl ms 180 c chainsaw did not hold idle and stalled. With difficulty started, but again stalled at idle. Then he does not want to start. The next day, after unsuccessful attempts to start, I removed and washed the air filter. It didn't help, I had to remove the candle. turned out to be dry, although attempts start it was enough. I cleaned the breather with a needle (it was not clogged). I changed the fuel filter (although the old one is not visually dirty). I cleaned the carburetor and, just in case, put the newest plug on. The saw will not start! He turned out the candle again. dry. On chainsaws calm ms 180 as idling on a chainsaw. What to do?

Remove the muffler. Look at the piston, if there are longitudinal stripes on it, then a replacement is required.

I have been using the Shtil 180 chainsaw for the 6th year, I took the newest one. I am satisfied with the saw, apart from oil, filters and bearing grease, I did not touch anything, I have done work over the years with decency. This year I had to cut a lot, I worked for three days. On the 2nd day, the saw began to podtrait, you will run out like normal. On the 3rd day, the revolutions fell by about 2/3. At idle, it works, from time to time it can stall, it does not start the first time. Yesterday I put it no more. How to assemble a stihl ms 180 chainsaw after purchase. What could be?

Read the same

I'd take a look at the muffler. If not once in 6 years have not been cleaned, it clogged up and the exhaust gases have nowhere to go. Usually, with these symptoms, either the air filter is clogged, or the muffler.

Not so long ago I found out that better at times turn the tire on the chainsaw. for even wear. Tell me, is it, is it worth doing?

Spinning a tire isn't just better. certainly. How often. depends on the amount of work. Not only twist, but also grind off the burrs.

What is the difference between the drive and chain sprockets of the Stihl 180 chainsaw?

There is no difference between a "sprocket" and a "sprocket", these are different names for the same part.

I bought this chainsaw, I really liked it, but I would like to ask you if my saw can cut a thick tree?

Standard bus length. 35 cm, can be sawn the log. 70 cm in diameter, if the logs of this diameter prevail, then you need a chainsaw of more power. The tool will, of course, cope with the task at hand, it will slowly and correctly cut all the logs of a huge diameter, but it is necessary to keep in mind that giving enormous loads to an apparatus that is not intended for this, you (in best case) we reduce the resource of the chainsaw, in other words, bring its complete repair closer.

Can you please tell me if a 45 cm bar can be used on a Stihl 180 chain saw?

The maximum length of the tire can be placed on the chain saw 40 cm.

Where is the breather in the Stihl ms 180 chainsaw?

Valve ventilation system("breather") is located "on top" of the gas tank and oil tank; there everything is closed by the starter housing.

In a horizontal position, the throttle button is stuck. What to do?

Most likely, the linkage mechanism is faulty; when the unit is turned over, one of the levers or rods "sinks".

Why isn't oil coming to lubricate the chainsaw bar? What is the problem?

Clogged oil filter. The channel in the chainsaw body is clogged. Clogged channel and tire groove. Defective oil pump drive (worm). Oil pump defective. The oil in the oil tank has run out.

What can you say about motor overheating chainsaw Calm 180?

I will try to clarify about the overheating of a serviceable chainsaw. I understand a working chainsaw as follows: the carburetor is correctly adjusted (it is enough to set the normal idle speed, by ear or by the tachometer 2800), bearings, oil seals, filters, and a candle. OK. The cooling system must also be in order, otherwise it happens that the color of the starter cover is not visible, the grille is clogged, the air practically does not pass. If a working chain saw runs on a normal fuel consistency (high quality gasoline with a fairly high octane number, not a bad two-stroke oil and its correct proportion). it is then that overheating actually cannot be (sharp chain. of course). What could be the reason that the calm saw 180 ms not. The reason for overheating is directly related to the fuel, you can overheat a newest saw in 5 minutes, while it is in good working order. Overheating reason. not work or its duration, but fuel or oil. Either this and that. And with home, moderate use, subject to all of the above, this tool will never overheat.

Chainsaws are slightly different design features, however, in most cases, the assembly principle is carried out in two standard schemes... For many devices, the instructions contain information on the need to activate the emergency brake before starting the activation procedure.

You should first master the device of the plant and study the main ways of correcting breakdowns, then a person will have the opportunity to fully operate the device.

Briefly about the device of the plant

The chainsaw is powered by an internal combustion engine. This is a simple device, the design of which does not have any special bells and whistles. It usually works well even under difficult conditions.

Functioning is provided by structural elements:

1. Carburetor engine (see).
2. Clutches of centrifugal type.
3. The ignition system is contactless in almost all devices.
4. A carburetor that adds air to the fuel mixture.
5. Fuel system. Her standard device consists of a hose, a filter and a gas tank, but sometimes it also has additional parts.
6. Starter.
7. Tire.
8. Chain (see).
9. Chain tensioner and brake (see).

Step-by-step instruction

When the brake is activated, the assembly process is much slower, so everything can also be switched on safely and more comfortably without the use of braking equipment.

If a person is not sure of their knowledge and accuracy, then the brake, on the contrary, needs to be activated. With the correct procedure, the device will not start, the mechanism will not perform actions that are dangerous to humans.

1 diagram of a standard mechanism

1. 1. Step 1. Before starting the benzoil, it is necessary to move the flap, which acts as an adjustment lever, downwards, in comparison with the optimal position. First, you need to press the button responsible for the gas supply. Only if this condition is met is the normal movement of the damper possible to the extreme stop from below. It is necessary to simultaneously move the damper and hold down the gas button. The gas is set to the standard position and the choke closes the carburetor, preparing the unit for correct operation.

1. Step 2. The starter handle should be pulled, and this is done in jerks, not soft movements. This action requires the use of moderate force. These jerks should be continued until the start of ignition of the chainsaw is clearly heard, which ends very quickly (dies down). After the implementation of this measure, the position of the damper must be moved up one step.
2. Step 3. Starter handle twitches again then until the system starts. When the device begins to actively work, a high speed is immediately noticeable, since the throttle stick is on high level... It must be remembered that sometimes chainsaws are supplied without a starter, then all actions with this element are released.
3. Step 4. The gas button is pressed once and then released, then the position of the damper will immediately become optimal. The speed drops, that is, the intensity of the chain revolutions.
4. Step 5. The already warmed-up chainsaw starts up when the lever is set to the “1” position, and then the actions are performed to turn on the device.
5. Step 6. To turn off the engine of the device, you must put the damper in the highest position.

Conclusion

The chainsaw should be started following the standard instructions. If there are any problems with the operation of the device, for example, it is necessary to quickly eliminate them or take the device for repair, and in order to identify malfunctions and correct operation of the chainsaw, you need to know the features of its design. To learn how to quickly turn on the device and fix breakdowns, it is enough to study the basic spectrum necessary actions and follow it.
Read on how to do it right before starting it for the first time.

Some buyers who purchase a STIHL chainsaw face the problem of starting it and, as a result, remain unhappy. But what is the reason that the purchased one does not start? Take your time to run to the warranty workshop and demand urgent repairs or ask the seller to replace the tool, and try to start over.

Refueling the saw with gasoline and oil

To start working directly with the saw, it is placed on a stable surface and filled with fuel. For refueling, use only "branded" oils, specially designed for. The percentage of oil in this mixture should be 1 / 40-1 / 50. For imported saws, it is better to use 92nd gasoline (or higher brand), and for Russian saws, 76th gasoline is also suitable (not to mention other brands).
To avoid the risk of fire, remove the saw from the place where it was filled with fuel before starting the engine and place it back on a solid, stable base.

Starting the saw for the first time

After checking that the chain is not touching hard surfaces, engage the chain brake. In this case, the brake lever is moved away from you so that the chain does not start to rotate ahead of time. Since the engine is cold, the choke lever is pulled out all the way. The toe of the foot is threaded into the rear handle (while holding the front handle with the hand). Pull the handle several times while pulling on the starter cord until the engine hums. After that, the air damper is moved to the working position and the saw is started. Briefly press the throttle, transfer the saw to idle. The brake lever is moved to its previous position towards itself. After all these steps, the saw is ready to work.

Saw care

Every time after working with the chain, it is necessary to check the tension and lubrication of the chain. If the chain is loose, it must be tightened, if the oil runs out, add it to the tank.

Refueling the saw

After finishing work, refuel the chainsaw after a short rest of the engine so that the saw cools down.

Checking the air filter.

Periodically, the saw air filter becomes clogged with chips - after finishing work, it is advisable to remove it, rinse and blow it out. Also, periodically it is necessary to clean the surfaces around the engine cooling plates from contamination.

Starting the engine with separate controls:

1. Starting a cold engine:

b. pull out the choke lever until it stops (the air damper is fully closed);

v. pull the starter cord handle several times until the first flash of fuel in the engine;

d. push the choke lever (choke is open,
high idle position included);

start the engine;

After starting the engine, immediately squeeze and release the throttle trigger - the choke lever automatically moves to the operating position (normal idle).

2. Starting a warm engine:

a. turn the switch to position 1 (on);

b. Pull the choke lever to failure, then move it to the forward position (increased idle speed), or without touching the choke lever, perform the engine start procedure;

d. when the choke lever is in the high idle position after starting the engine, press and release the throttle trigger;

Stop the engine by moving the switch to the (off) position.

Today's tips are for preparing gas powered tools and garden equipment to long-term storage or winter season. Moreover, in most cases, the owners of gasoline-powered tools and garden equipment take this somewhat lightly, which is fundamentally wrong. Why the cultivator does not start when you are about to carry out autumn processing soil, if the machine worked perfectly in the spring? What happened to - after all, you bought it only six months ago, once the boards were cut and since then it has been filled up, ready to go? All these are the consequences of neglecting mandatory procedure- preparation of the instrument for storage.

So, there is nothing complicated in storing a motor-cultivator. It is a unit with a four-stroke engine, which is still less whimsical than a two-stroke. Here, the main and prerequisite for preparation for storage is the absence of gasoline in the working area of ​​the engine. It is necessary to drain the gasoline and then start the engine of the cultivator in order to use up the fuel in the carburetor - the engine will stall and that's it, you don't need to do anything else. Well, except to inspect the motor for possible problems in order to know what parts or consumables you need to purchase.

If the gasoline from the tank of the cultivator does not drain or is drained, but the engine is not started, then the gasoline remaining in the carburetor softens the rubber membranes and they stick together. As a result, the motor stops working. This problem is especially relevant for those cultivators for which it is very, very difficult to find spare parts.

The situation regarding preparation for storage of chainsaws and brushcutters (trimmers) with two-stroke engines is much more complicated. Although the preparation procedure is almost the same - drain the fuel and start, that is, produce gasoline from the carburetor. But the consequences of not fulfilling the conditions of preparation in this case are more serious. Fuel for two-stroke engines is gasoline + oil. Gasoline evaporates easily, but oil remains on the walls of the working area of ​​the engine and the needle-thin channels of the carburetor. And it is impossible to remove or clean this layer, which has hardened in 2-3 months. One thing remains - to change the carburetor, which is very expensive.

Remove the tire and clean all grooves and oil channels on it, since mixed with oil form a viscous consistency that is extremely difficult to remove;

Remove all easily accessible covers and clean the engine cylinder stiffeners and all other surfaces with a brush, brush, air jet;

Unscrew the spark plug, pour a little oil for two-stroke engines into the cylinder. Pull the starter rope several times to distribute the oil evenly over the cylinder and piston walls. Screw in the candle again. This must be done to prevent oxidation and corrosion;

Loosen or remove the tire. It is good to put it in oil for a day;

Inspect the parts of your chainsaw to determine what needs to be replaced. The chain may need sharpening, the bar is worn out, or the sprocket needs to be replaced. There's a whole winter ahead for troubleshooting.

Now about the storage of gasoline. As a rule, he stays. So gasoline mixed with oil cannot be stored for more than 50-60 days, even in a specialized container. In a simple oil-resistant canister, the gas-oil mixture is stored for no more than 30 days.

It is absolutely impossible to store in plastic bottles, where we love to mix gasoline and oil. Gasoline eats away at the walls of a plastic bottle and plastic fractions enter the fuel mixture, completely clogging the carburetor channels. In order not to clog your head, just pour out all the gasoline intended for the gasoline tool without regret.

If you plan to use a chainsaw and use it from time to time in winter, then you need to start the chainsaw at least 2 times a month and cut at least a couple of chocks with it. And it is better to store the chainsaw in a dry place.

Hello Dear STIHL petrol power tool customer.

Some buyers who purchase a STIHL chainsaw face the problem of starting it and, as a result, remain unhappy. But what is the reason that you have acquired? Do not rush to the warranty workshop and demand urgent repairs or ask the seller for a replacement tool, but try to start all over again. how to start a stihl chainsaw ?

So, first, carefully read the instructions for the tool you purchased and make sure that you did everything correctly: you filled in oil for the chain, filled in a gasoline mixture diluted with two-stroke oil, set the chain tension correctly. The chainsaw can now be started. Move the combination lever (located to the left of the handle) to the lowest position (cold start). Start the saw two or three times in this position of the lever, while it should not start. After that, move the combined lever to the next position (start in a hot state) and already in it make the chainsaw plant. Your saw should start easily. As soon as the saw has started, briefly press the throttle lever (be on the handle of the chainsaw), while the combined lever should automatically switch to the working position (I) and the engine goes into idle mode. The motor must switch to idle speed immediately, otherwise damage to the motor housing and the chain brake may occur if the saw chain brake is engaged. Your saw is now ready for use.

If, nevertheless, yours does not start, move the combined lever to position (0), dismantle the spark plug, wipe the spark plug with a dry cloth. Pull out the starter several times - to ventilate the combustion chamber and reinstall the spark plug to start the engine following the instructions given earlier.

Many people buy chainsaws for the first time without having experience with this tool. Despite this, there is no need to take special courses to learn how to use the tool. After the purchase, there is a great desire to quickly test the tool in work. To do this, be sure to first read the operating instructions for the tool, as well as safety precautions when working with a chainsaw. In the material, we will consider how to properly start a chainsaw, as well as work with it.

Every craftsman who has a chainsaw should know how to start it correctly. Initially, it should be noted that in order to start the tool, it must be filled with fuel. For this, not just gasoline is used, but a gasoline-oil mixture.

It's important to know! You must not refuel clean gasoline for the operation of chainsaws. Only fill with a mixture of gasoline and the appropriate oil for two-stroke engines.

First you need to figure out how to properly prepare a gasoline-oil mixture. These proportions are naturally indicated in the instructions, but since few people read them, this issue should be considered in detail.

Gasoline of AI92 and higher grade is used as fuel. You will also need to use the appropriate oil, which can be purchased in the same place where the chainsaw was bought. The proportion of gasoline and oil is 1 to 50, after mixing which, it is necessary to stir thoroughly. In this case, the mixture should be prepared in a separate container ( plastic bottle), since it is not only convenient to store the prepared fuel mixture in it, but it is also convenient to fill the tool tank through the small diameter of the gas tank hatch.

The prepared mixture should be poured into the fuel tank, the cap of which is indicated in the form of an image of a gas station. This is very important as chainsaws have two similar tanks. The second tank is intended for filling with oil, which is used to lubricate the bar and chain during the operation of the tool.

It's important to know! After refueling the fuel in the gas tank, do not rush to start the tool. Be sure to also fill the oil tank with oil to prevent overheating of the chain, which could damage the chain as a result.

It is recommended to use a special brand or engine oil for a car, but by no means a working off. If you see how your neighbor is refueling the working off in the chainsaw, then you should not repeat his mistakes, as this significantly reduces the service life of not only the chain, but also the tool itself.

It is always necessary to control the level of oil and fuel mixture in the tanks, but it is recommended to refuel as follows:

• The fuel-oil mixture is filled into the tank until it is full.
• At the same time, the chain oil is also filled up to full.
• The consumption of oil and fuel mixture is approximately the same, therefore, it is recommended to fill both tanks at the same time.

How to start a chainsaw: starting features

Once the tool is ready to run, you can proceed. The process of starting a chainsaw is as follows:

Having started the chainsaw, you can start sawing wood.

It's important to know! The material describes the process of launching the tool, after which you can start working with it. Do not forget that if you bought new chainsaw, then it should initially be run in.

How to use a chainsaw correctly

Chainsaw operation is one of the most dangerous, therefore it is very important to control the location of the tire as far away from you as possible. Each subsequent action must be deliberate, otherwise the consequences in the form of serious injury cannot be avoided. If you have to work with a chainsaw, then you should know the following features:

1. It is required to work exclusively in the appropriate work clothing: a protective helmet, headphones, a suit, gloves and shoes. This will increase the safety of the master several times.
2. You need to hold the tool only with two hands, and with your feet take the appropriate position in the form of a reliable stop. Working while standing in an uncomfortable position is strictly prohibited.
3. Lean the tool against the wood with the chain moving at medium speed.
4. Use extreme caution when sawing with the tip of the tire, as there is a high likelihood of kickback.
5. When working, exclude from the cutting area all unnecessary objects that can cause imbalance.
6. If you are tired, then you need to muffle the instrument, allowing you to rest not only yourself, but also him.
7. When working, the legs should be wide apart, and the back should be straight.
8. You can cut wood not only with the lower part of the tire, but also with the upper one, only in this case it is important to know that the chain will lead in the appropriate direction.
9. When moving from a chainsaw to another place, the tool should be muffled or put on the handbrake.

The above features are also suitable for electric saw operation. It is better to do the work in tandem with a partner who can not only insure, but also replace you when you get tired. After all, it is not easy to work with such a tool, since in addition to physical strength, it also requires ingenuity. Observing the above rules for working with a chainsaw, all types of manipulations performed will have a successful conclusion.

Chainsaw care

Another important condition to work with the tool is to ensure proper care of it. After completing the work, you should not abandon the chainsaw at the workplace until the next time. It is necessary to clean it of sawdust and debris, periodically check the tension of the chain, as well as the fullness of the gas tank and oil tank. It is also important to monitor the clogging of the air filter.

It is not recommended to store the chainsaw with filled fuel for a long time, therefore it is better to drain it. It is necessary to replace the chain, tire and drive sprocket in a timely manner, as these are elements that wear out quickly.

In conclusion, it is important to note that over time, the chain tends to stretch, which as a result leads to the fact that it cannot be pulled. If you observe such a property, then it is not recommended to continue to operate the tool until cutting tool will not tear or jump off the tire at all. If a person is not confident in his abilities, then it is better not to take up sawing trees of large diameter.