The bathroom is one of the most visited places in the house. Constant washing leads to the accumulation of a large number of hair and other organic waste. As a result, a strong blockage is formed, and the water does not leave, and in the future it may appear bad smell from the plum. You can clear the blockage in the bathroom using simple means.

At home, a plunger will help to cope with a clogged blockage in the bathroom. In order to avoid an air passage, it is necessary to close the upper water drainage hole with a plug or rag. Vaseline or any greasy cream will help to ensure a tighter fit of the plunger to the rim of the toilet. Then you need to put the plunger on drainer and begin to vigorously and abruptly drive out impurities in order to get rid of them.

If the use of the previous method did not bring any results, then you can proceed as follows. For more effective protection against blockages, it is necessary to fill the bathtub with water exactly one third. Using a plunger, pump it into the pipeline and pull it out. At the same time, movements should be sharp. It is necessary to continue a similar procedure until it is possible to completely pierce the drain hole in the pipe from contamination.

Mechanical cleaning with a rope

What to do in a situation when boiling water in combination with a plunger cannot cope with blockages in the sewer? In this case, the most the right way there will be a cable. Care should be taken, since it is easy to damage plastic pipes with such a device, and they will leak.

To make your own cable, you need a flexible metal wire. Then one end of the cable must be bent to form a small hook. It will be convenient for them to catch the debris stuck in the drain hole and pull it out. As for the second end, then a piece of fabric should be tied to it, making a handle.

It is necessary to carefully tuck the cable inside the drain pipe and try to push through the accumulated dirt. For better cleaning, you can turn the tool clockwise. Then you need to pull out the cable with the remaining debris.

To flush out the blockage completely, it is necessary to flush the drain with a strong stream of boiling water from the shower or tap. This method is one of the most effective today. This is what most plumbers use.

Soda for small blockages

Soda in combination with baking soda will help to cope with a small blockage in the bath without a plunger. For this:

• pour 125 mg of each product into the drain hole;
• pour soda and salt with 3 cups of boiling water;
• do not use the bathroom for 7 hours;
• after this time, the drain should be flushed hot water.

One of the most popular ways to remove debris from the drain with handy tools is to use baking soda and vinegar. These components react with each other and effectively remove the blockage. For such a procedure, you will need acetic acid 70% (200 ml) and 3 tbsp. l. soda.

Be careful when handling vinegar as it is very easy to get a chemical burn. Soda is poured into the drain and poured with acetic acid. Then you should wait 40-50 minutes and gently clean the drain with boiling water until the foam from the soda and vinegar disappears completely. It should be remembered that this method will only help to destroy organic waste. If the bathtub is clogged and needs to be cleaned of inorganic contaminants, then it is best to use a cable, plunger or store-bought preparations.

Other effective ways

If the tub is not too clogged, you can use lemon. To do this, squeeze the juice from three medium citrus fruits into the drain and wait 40-60 minutes. To get more juice, you can pre-hold the lemons in boiling water. After that, you need to spill the drain with very hot water. Thanks to this method, not only the debris in the bathtub is eliminated, but also the unpleasant odor.

Video - Proven Cleaning Methods:

You can remove dirt in the drain hole with a vacuum cleaner that is equipped with a backflush function. The action of this method is based on the use of a strong air pressure. Experts do not recommend using this method, as water can get into the vacuum cleaner. If you do decide to remove the blockage in the tub using this method, you should wipe the rim of the drain hole dry. Then attach the vacuum cleaner tube, previously wrapped with a rag, to the drain and turn on the backflow.

What if traditional methods do not help?

Chemicals available at hardware stores can help you quickly and effectively remove clogged debris. They are designed to eliminate contaminants that have organic basis(hair, pet hair, food debris, etc.). They resort to their help when it is impossible to cope with a clogged bathroom with folk remedies.

In what form is best to acquire household chemicals? Despite the fact that these drugs are sold in the form of foams, powders, gels and granules, they all have almost the same composition.

Cleaning up clogged sewer pipes in the bathroom with KROT cleaning agent - video:

The following tips will help you clean up a heavily soiled pipe:

• it is very important to read the instructions before using chemical clogging solvents;
• experts recommend choosing solvents in order to remove blockages by the nature of the pipe (for example, plastic or cast iron);
• both powder and liquid preparations have the same effectiveness, so it does not matter which type of preparation will be used to clear a strong blockage in the bathroom;
• clogging solvents in liquid form are immediately poured into the drain, and granules or powders are poured, and then boiling water is poured into them;
• after the drug has run out of the time allotted for it by the instructions, you need to thoroughly rinse the drain with a stream of hot water.

It is also very important to wear rubber protective gloves when handling such chemicals.

Measures to prevent contamination in the bath

In order to prevent contamination in the drain of the sink or bathtub, it is necessary to devote time to preventive procedures. Their implementation does not require a lot of time, and the tools that need to be used will be found in every home.

To water pipes were not contaminated with waste, and there was no situation where water does not go well, it is necessary to close the drain holes with special nets for protection. This device will help minimize food particles and other organic waste entering the drain.

1. The accumulated debris should be dissolved at least once a month. This even applies to situations when the blockages are not too large and water flows freely into the sewer. This procedure will save you from the formation of traffic jams. It can be carried out using the tools sold in the store (Mole, Tiret Turbo, etc.).
2. Replace such chemicals, can ordinary washing powder. To prevent blockages, it is necessary to close the drain holes of the bathtub and sinks every 4–5 months. After that, add a handful of powder and cover with very hot water. Remove the plugs after 5 minutes. This method will also help to get rid of bad smell from the plum.
3. To prevent blockages from appearing for a long time, you can spill the drain hole with boiling water from the kettle. This procedure should be carried out within 2-3 minutes.

It is also very important to remove any hair that has been trapped in the drain after every shower.

If the water does not pass well into the drain and an unpleasant odor appears in the room, it is necessary to urgently take measures to remove the blockage in the sewer hole. Alternatively, you can use the services of a specialist or solve the problem yourself. Want to save money and do it yourself? No question, because after reading our article, you will learn how to remove the blockage in the bathroom and cope with the task as quickly as possible.

The main "culprits" of blockages

First you need to figure out for what reasons there is a blockage in the pipe in the bathroom? Most often, this problem arises as a result of human activity. The bottom line is that a person cannot keep track of what goes into the drain, because we are talking about long hair, animal hair, particles of rags. All this garbage is compactly packed in the sewer and forms a lump that blocks the passage of water.

It is then that stagnation of water arises, with which you need to start the fight in time, without postponing this process until later.

It is better to prevent a blockage of a pipe than to look for a way out of the situation.

By the way, in multi-storey building the blockage can be local, that is, in one apartment, or general, if the central sewerage system of the building is clogged. To determine the type of blockage, you should turn on the water in the kitchen and bathroom: if the problem is only in one place, the blockage is local and you can remove it on your own.

Speaking about the causes of blockage, one cannot fail to mention the following factors: fatty deposits in pipes, wear sewer system... In short, there are several reasons, so the question of how to clear the blockage in the bathroom is extremely relevant.

Using a plunger is a traditional method

It is much more difficult to break through a blockage with a plunger in a bathroom than in a sink, because draining the water complicates this process. The problem is that when water begins to overflow, air enters the opening, and a vacuum is needed to work with the plunger.

The plunger must be selected taking into account the size of the drain hole

How to use a plunger to clear a blockage in the bathroom? First, the aforementioned water overflow hole is tightly closed with a stopper, and then the plunger previously lubricated with Vaseline is firmly pressed against the drain and 10 sharp reciprocating movements are made.

This is important to know: instead of a cork to create the greatest tightness, you can use a second plunger, but then you will need the help of another person.

If there is no result, you can try to push through the blockage not with air, but with water. To do this, pour hot water into the bathroom (about half the height of the rubber bowl) and immerse the plunger in the water at an angle. With the last swing, the plunger should be pulled out of the water sharply. In the case when the blockage is not eliminated the first time, the procedure is repeated several times.

Plumbing cable is a more serious way of cleaning

Everyone understands perfectly well that only small blockages can be cleared with the help of a plunger, so it is necessary to consider other methods of dealing with this nuisance.

Plumbing cable must be taut when clearing the blockage

If the blockage is far in the pipe or it is strongly compressed, they resort to cleaning using a cable. The essence of this method is that you need to hook the debris with a plumbing cable, pulling it out or pushing it into a wider highway.

This procedure is as follows:

• the cable is inserted into the drain hole;
• one person pushes the cable, and the other rotates it;
• after passing the clogged place, you need to make a couple of sharp jerks back and forth, then open the hot water tap and carefully pulling out the cable, wash off the dirt formed in the sewer pipe.

It is worth paying attention: the rotation of the cable contributes to the better destruction of the blockage.

You can find your plumbing cable at a hardware store, but you can also make your own. To do this, you need to take a piece of a sufficiently flexible metal cable, bend it and slightly fluff the tip. Thanks to this manipulation, the cable will move well along the bends of the pipe and will not rest against the knee.

This is important to know: for the convenience of gripping, the cable should be wrapped with something rigid to get a kind of handle.

It is also necessary to mention the fact that the plumbing cable absolutely cannot be used to clean plastic, chrome-plated pipes - then their inner surface can be damaged.

Chemicals are faithful helpers

And how to remove the blockage in the bathroom with the help of sewage cleaning agents and which drug to give preference to? As for the first point, there is nothing complicated here: I bought a cleaning agent in a specialized store, read the instructions carefully and did everything in accordance with the written information.

This is important to know: the product is poured or poured into the sewer hole, left there for a while, and then rinsed thoroughly running water.

In addition, we want to draw your attention to the fact that chemical agents must be used correctly, since even the safest drugs, with prolonged use, cause deformation of the material from which the pipes are made.

Chemicals are effective, but too frequent use destroys pipes

Solving the question of how to break through the blockage in the bathroom, modern man faces another problem, because there is a wide range of cleaning products on the market. Therefore, the most popular drugs should be named in order to facilitate the choice of our readers:

• "Mole" - effective remedy which cannot be applied to plastic pipes;
• Mister Muscle is a product suitable for all types of pipes. It comes in the form of a gel or foam. "Mister Muscle" cleans the pipes from dirt, penetrating into all the nooks and crannies. It also kills bacteria, thereby helping to eliminate odor;
• Tiret removes blockages quickly and efficiently. It does not smell of ammonia and, according to user reviews, does its job perfectly;
• "Potkhan" is a substance that quickly and without residue dissolves a variety of impurities. It has a pungent chemical odor, but it breaks through even the most severe blockages.

When using a blockage cleaner, you need to remember about safety precautions, that is, when working with alkalis and acids, you should be properly equipped.

This means wearing rubber gloves, goggles and an oilcloth apron.

It is better to prevent a problem than to deal with it.

Yes, if a person regularly carries out blockage prevention, he will avoid many troubles. What do you need to do for this? First, it is necessary to install a protective mesh on the water drain hole: it will protect the pipes from dirt, animal hair and hair getting into them. Secondly, good remedy For prevention, chemical agents are considered - the main thing is to use them in accordance with the instructions so as not to damage the pipes. All in all, correct operation and timely preventive measures extend the service life of communications, ensure their reliability and prevent blockages.

We hope that the information provided in this publication will help you solve the problem of how to remove a blockage in the bathroom. And also, remember that the most the best way removing the blockage are preventive measures. Performing them, you can be sure that unnecessary discomfort will not be created in the bathroom and that you will not have to use a plunger and a plumbing cable.

You can remove the blockage in the sewer pipe yourself. It is not necessary to call a plumber.

You can save a lot by cleaning the pipe with home remedies or household chemicals.

Causes

A dirty bathroom drain can lead to serious plumbing problems. If the drain is clogged, all the dirt flows back into the container, it will not be very pleasant to take water procedures when mold with hair and soapy water will crawl out of the drain hole.

Signs of a blockage in the bathroom:

1. Water drains off more slowly than usual.
2. The dirt flows back into the container.
3. Puddles of water around appliances with drains.

Before cleaning, you need to find out the reason why the drain in the bathroom is clogged.

The most common reasons why pipes are clogged are:

1. Hair and dead skin cells stick to the walls and, if not cleaned, begin to accumulate.
2. Clogging occurs due to the frequent washing of things in the bathroom, the constant use of water procedures. The water itself flows down the drain, and the soap settles on the walls.
3. A clogged pipe must be cleaned once a month. Prolonged lack of proper care leads to the appearance of growths, limescale... The pipes begin to loosen and a leak appears.
4. The sewage system quickly clogs up if its installation was incorrectly carried out during the repair. Due to the low incline, dirt accumulates faster.
5. Do not make many bends when installing the pipeline. They also collect more hair, grease, sand and other debris.
6. The sewer pipe should not be narrow. Otherwise, you will have to clean it very often, because it clogs up faster.

Having found out the cause of the clogged sewage system, you can start cleaning it.If you are not sure that you will cope with the task at hand, then you cannot do without the intervention of a specialist.

Mechanical methods

Mechanical methods can be used to clean the sewer system. These include a plunger, rope or vacuum cleaner.

With the help of such methods, it will be possible to quickly remove the blockage.

Ventuz

They perfectly pierce clogged pipes with a plunger. It consists of a long, straight handle with a flexible rubber cup mechanism mounted at the bottom.

This rubber piece acts like a suction cup, pulling out any debris. At home, this is the simplest method that perfectly cleans any drain holes.

How to unclog a blockage in a bathroom:

1. The best result will be achieved by plugging the hole above the drain, which is intended for overflowing water.
2. Do not use chemicals while using a plunger. During the procedure, hazardous substances can get on clothes or skin, leave burns.
3. The base of the plunger must be covered with water.
4. Place this item over the drain hole. The rubber cup must cover it completely. The handle should be upright. Tilting it slightly will reduce the pulling force of the dirt.
5. Press down on the plunger so that it sucks well. Then move the handle up and down for 15–20 seconds.
6. Then you need to pull out the plunger and look at the result. If the water drains well, you can stop the procedure, if it's bad, repeat it.

After clearing the drain from the blockage, turn on hot water to rinse the remaining dirt. Gradually increase the pressure so that no trace remains of the blockage.

At home, they clean the sewer systems using a plumbing cable. If the plunger does not help, you can use this device.

Plumbing rope is a flexible metal rope that is made with a diameter of 6 mm and up to 5 m in length.

You can also make it yourself. For example, take a wire hanger and straighten it, and at the end they make a small hook, with which it will be more convenient to pull out the hair.

How to remove a blockage in the bathroom:

1. The wire is carefully inserted into the drain hole so as not to damage the siphon. Simultaneously with the introduction, it is necessary to rotate the cable.
2. When the cable is inserted to the maximum possible depth, turn it 2-3 times and pull it out.
3. Hair and other waste will cling to the hook. You can repeat the procedure until all contamination is removed.

After that, hot water is turned on to cleanse the sewer system.

Vacuum cleaner

You can also clean the siphon and remove the blockage from the pipes. The household appliance is convenient to use.

How to remove the blockage:

1. The rubber nozzle from the plunger is installed on the pipe of the vacuum cleaner and properly secured with electrical tape. Don't worry, the glue can be cleaned with rubbing alcohol.
2. Remove the garbage bag from the household appliance and connect a hose with a pipe to the blow hole.
3. It remains to turn on the device and start cleaning the drain hole.

This is the easiest method for cleaning a siphon at home.

Exists whole line commercial products specially designed for drain cleaning.

When using household chemicals, be sure to protect your hands with rubber gloves, wear a respirator and goggles.

To remove the blockage, you can use the following tools:

1. Domestos - irreplaceable assistant in cleaning the bathroom. Cleaning with it does not take much time. Domestos can cope with this problem no worse than specialized alkaline products. How to use it: pour 7-10 caps of the product into the drain hole and leave it overnight. It is important that no one uses the bathroom at night, so you should warn all household members. In the morning, they remain to rinse the pipe big amount hot water.
2. Mole sold in liquid form. The entire procedure takes approximately 90 minutes. The liquid is poured into the drain hole, kept for the prescribed time (indicated in the instructions). Then the systems are flushed with hot water, simply by opening the tap. If the product accidentally gets on the skin, rinse immediately clean water and go to the nearest burn department.
3. Tyreth- an excellent tool if you need to clean the sewer pipes and siphon at home. The liquid is a gel, unfortunately, it is not used economically. One bottle is enough for only 2 cleanings. Tiret is poured into the drain hole, and left to act for 5 minutes, if the blockage is strong, you can stand it for 30 minutes. The remaining cleaning agent is washed off with running water. Tiret should not be mixed with acids, as the reaction can cause severe burns to the respiratory tract.
4. Mister Muscle can be used for cleaning drain pipes of all kinds. The substance is granular, but it can also negatively affect the condition of the skin, so do not forget to wear rubber gloves. Mister muscle is poured into the drain hole and left for half an hour. During this time, the chemical will have time to eliminate not only the blockage, but also kill pathogenic microorganisms, remove the stench. Then rinse the drain hole with hot water.
5. Sky another noteworthy remedy for. It destroys germs, dissolves soap deposits, hair and even threads. The product is on sale in sachets. The contents of one sachet are poured into the sewer hole, which must be unclogged, and wait 15 minutes. Then the residues are washed off with running water. Be careful when removing residual agent around the drain hole.

Household chemicals will solve the problem well and quickly. But if you are an asthmatic and a respirator does not help, it is better to use folk methods of removing a clogged pipe.

Folk remedies

In the life of every person, sooner or later there comes a moment when there is a problem with how to clean the siphon in the sink and remove the blockage in the bathroom.

If the house does not have a plumbing cable or plunger, you can use folk remedies.

There are many ways you can use baking soda. But for its application it is necessary that there is no water in the bathroom.

Correct elimination Problems:

1. Bring rubber gloves and goggles to protect your eyes. Caustic soda can cause chemical burns and has fantastic degreasing properties. It is easy to deal with a clogged drain if there is such a remedy in the house. Take a bucket and pour 2 liters of water into it, add 3 cups of caustic soda. Mix the solution well with an old wooden spoon. When the liquid starts to sizzle, pour it into a clogged siphon. Let the solution work for 20-30 minutes, then turn on the hot water. The procedure can be repeated if it was not possible to clean the clogged drain the first time.
2. Mix ½ cup table salt with ½ cup baking soda, add water and pour into a pipe. Let it sit for 10-20 minutes, then pour in boiling water. Salt, baking soda, and boiling water will create a chemical reaction that should dissolve the plaque.
3. Baking soda and vinegar are natural alternatives to chemicals. This method is environmentally friendly and will not harm plastic pipes... Pour boiling water down the drain. Then add ½ cup of baking soda and push it inside. Leave the drain alone for 5 minutes. Next, pour in 1 cup vinegar and 1 cup boiling liquid. The baking soda and vinegar will fizzle, this chemical reaction will help clear the pipe. After 10–20 minutes, pour a kettle of hot water down the drain to flush out any dirt weakened by this product.

Baking soda, vinegar, and salt are cheap remedies that can be found in the grocery section. These cleaning agents quickly remove dirt from the pipes and flush out the siphon.

Boiling water

This method can be applied regularly, even every day. But if the pipe becomes heavily clogged, the boiling liquid may not help.

Boil more water and pour it slowly down the drain 2-3 times, letting the hot water work for a few seconds. This is the most quick way cleaning the drain if the bathtub is clogged.

Dish detergent

Dishwashing detergent is capable of breaking down grease stains. It can be used if you need to clean the siphon or.

What to do to break through the drain - the algorithm of actions:

1. First, boiling water is poured into the sewer.
2. Then add ¼ cups detergent for dishes.
3. Wait 15–20 minutes and refill the boiling water.
4. After half an hour, you can turn on a large pressure of hot water and rinse thoroughly.

Dish detergent can be used in conjunction with a plunger. This makes cleaning even better.

Sulphuric acid

Sulfuric acid is good chemical, commonly used to unclog a bathroom pipe if it is heavily clogged.

Sulfuric acid is a harsh chemical and can be used, but plumbers do not recommend it. They argue that it will not work to get rid of the blockage with its help, in addition, its use will lead to the destruction of the sewage system.

Better to buy household chemicals that can be found on the counter of any hardware store.

This method of cleaning sewer systems is very effective. Washing is fast and efficient.

The main advantage of the hydrodynamic method is that it does not damage the pipeline; on the contrary, its service life is extended, since the method is gentle.

This method is also environmentally friendly and destroys deposits of any kind.

Hydrodynamic cleaning is carried out only by plumbers, since it requires special equipment to use it.

The technique involves the release of a jet of water under pressure, its temperature can reach 120 degrees.

It is recommended to carry out flushing by hydrodynamic method 1-2 times a year. Thanks to this cleaning method, the sewer system will operate smoothly throughout the year.

Prophylaxis

The likelihood of blockages is higher if the sewer pipes are already old. In order to clean the drain holes as little as possible, you must first replace the entire system.

Remove dirt from the outside whenever possible. After each shampooing, it is necessary to put on rubber gloves and remove them from the drain hole.

It is also necessary to use a plunger at least 2 times a week, as well as after each shampooing. This will remove all hair from the drain hole.

Such simple measures will not allow dirt to quickly accumulate on inner surface pipes.

Cleaning the sewer system can be done not every week, but once a month. If the drain becomes clogged faster, then cleaning should be done more often.

Many people have to deal with such a problem as a blockage in the bathroom. Contamination can appear even if the bathtub is very clean, because there are many reasons for such situations. Of course, neat owners have to deal with blockages much less often, but they should also know how to most effectively clean pipes at home. This article discusses the most popular methods for getting rid of heavy and minor dirt.

Causes of occurrence

If you do not clean it regularly, contamination in the sewer pipe can cause serious problems with your plumbing. When the drain is clogged, the water does not go well, it stands, and the dirt ends up in the bath. It becomes very unpleasant to take water procedures.

Among the most common causes of blockages, several can be distinguished.

• Dead skin cells and hair adhere to the walls. If left untreated, dirt builds up over time and clogs the drain hole.

• The bath becomes dirty due to regular water procedures, frequent washings. Traces of soap remain on the walls, which accumulate over time, although the water itself ends up in the sewer.
• Long absence necessary care can lead to the formation of limescale. You can ignore the appearance of such a blockage for a long time until the situation becomes too serious. Dirty pipes must be cleaned monthly, otherwise they may become unusable over time.
• If the sewer is often clogged, it is possible that its installation was carried out incorrectly. Contamination can quickly accumulate if the slope is very low.

• When installing the pipeline, you need to ensure that there are not too many bends. They can collect sand, grease, hair and other contaminants.
• Avoid choosing a pipe that is too narrow. Dirt in such elements accumulates much faster.

Having figured out what exactly caused the pollution, you can decide how best to eliminate it. If you think that you will not be able to deal with the problem on your own, you can seek help from a specialist. However, many people choose to do their own cleaning to keep their budget. There is nothing difficult in such work. You just need to understand some of the nuances in order to choose the best remedy.

Remedies

A pipe that is clogged can be cleaned mechanically, chemically or folk method... Many people prefer to combine these methods to improve cleaning efficiency. Let's consider the main features of each method.

Mechanical

Among the most common mechanical methods cleaning sewer pipes in the bathroom can be distinguished by the use of a cable, a plunger or a vacuum cleaner. If everything is done correctly, it is quite easy to "break through" the blockage.

Ventuz

Many people prefer to use a plunger to get rid of blockages, so this simple device is available in many apartments. It is a flexible rubber product with a long straight handle. The rubber element is used as a suction cup. The plunger is well suited for cleaning a wide variety of drain holes.

When going to remove dirt that has gotten into the drain hole, you need to consider several points.

• When using a plunger, do not use additional chemicals. Chemicals can spill onto skin or clothing and cause burns.
• Before using such a fixture, moisten its base with water.

Place the plunger over the drain hole. Make sure it is completely covered by the rubber cup. Place the handle vertically. In order for the plunger to suck well, you need to press on it.

Move the device, then remove it and evaluate the result. If the bathtub is very clogged, repeat the procedure. If you clean the drain and remove the blockage it turned out, you should rinse the device with hot water to remove the remaining dirt.

Cable

The pipe can be effectively cleaned using a sanitary wire. You can use this device if the plunger does not help. You can create a plumbing cable with your own hands. To do this, straighten the wire hanger and bend it at the end, making a small hook. With this tool, you can easily remove stuck hair.

Use the wire rope as recommended by a professional.

• Carefully insert the fixture into the drain hole. In this case, it must be rotated.
• When the cable is at its maximum possible depth, turn it several times and remove it.
• There will be hair and other debris at the end of the cable. Follow the procedure until you can completely get rid of the dirt. Then you will need to turn on hot water.

Vacuum cleaner

Some people use a vacuum cleaner for cleaning. Such a device is very convenient to use.

To remove the blockage, the vacuum cleaner is used in a certain way.

• Take the rubber nozzle from the plunger and attach it with electrical tape to the pipe of the vacuum cleaner. Then the product can be cleaned of glue using alcohol.
• Remove the trash bag from the vacuum cleaner and connect a hose with a pipe to the blow hole.
• Turn on the vacuum cleaner and start cleaning the drain.

Chemical

Using chemicals it is necessary to wear rubber gloves to protect the skin of the hands. You should also protect your face with special glasses and a respirator.

Several products work well for pipe cleaning.

• Domestos. This tool can be called one of the most popular, because cleaning with it is very quick and convenient. In the evening, pour it into the pipes (10 caps will be enough) and wait until morning. You should not use the bathroom at night, so inform all family members about the procedure in advance. When cleaning is complete, flush the pipes with hot water.

• "Mole". This product is very effective in dissolving hair and other impurities. The whole procedure will need to be spent about one and a half hours. Pour in the liquid, wait (how much is usually written in the instructions). Then turn on the tap and rinse the drain hole with hot water.
• Tiret. Quite an effective remedy, but usually one pack is enough for only two procedures. Fill with Tiret and wait a few minutes (if the contamination is strong, you can wait about half an hour). Then rinse off with water. Tiret should not be used with acids, otherwise the respiratory tract can be severely damaged.

• Mr Muscle. This remedy is suitable for the most different pipes... It is granular, but it can also damage the skin, so rubber gloves must be used. Add the product and wait about 30 minutes. Mr Muscle will remove not only dirt, but also harmful microorganisms. It also effectively removes unpleasant odors. After using Mr Muscle, fill the drain with hot water.
• Sky. This tool can be called universal. It dissolves hair, removes soap residues, destroys harmful microorganisms. The product is sold in a sachet.

Pour the substance into the drain and wait about 15 minutes. Then rinse it off with plain water. Remove Sky with the utmost care.

Chemicals are quite effective. However, if you suffer from asthma, for example, it is better to prefer some other method of cleaning the drain hole. One option is to use folk remedies.

Folk

With the help of folk remedies, you can clean the drain quite effectively. You just need to know how to use them correctly. Let's consider the most popular options.

Soda

Baking soda can be used different ways... However, in any case, it should be borne in mind that when using such a product, there should be no water in the bathroom.

You need to use soda like this:

• Wear safety goggles and rubber gloves. The use of caustic soda can cause chemical burns. Pour about 2 liters of water into the bucket. Pour caustic soda into it (3 cups are enough for cleaning). Take old spoon made of wood and mix thoroughly. When you hear a hissing sound, pour the resulting liquid into the drain hole. Then you need to wait about half an hour and rinse the drain with hot water. If it does not clear the first time, you can repeat the procedure.

• The following method also allows you to achieve good results... You need to mix baking soda (use half a glass) and table salt (half a glass will do as well). Wait about 20 minutes and top up with boiling liquid. As a result chemical reaction you get a product that effectively dissolves the dirt.

Vinegar and baking soda are gentle agents that do not damage plastic pipes. Pour boiling water into the drain hole. Pour baking soda halfway into a glass and push it down the drain. Wait a few minutes, then pour a cup of boiling water and the same amount of vinegar. When the hissing sounds are heard, the cleaning process will begin.

When about 20 minutes have passed, you will need to pour a kettle of hot water into the drain. This will wash away any dirt weakened with this product.

Boiling water

There are no restrictions on the use of such a tool; with boiling water, the drain can be cleaned daily. However, it will not help if the pollution is very strong. Water must be poured into the drain hole several times. The hot liquid acts for a few seconds.

Dishwashing liquid

With these tools, fat can be removed quite effectively.

They should be used as follows:

• pour boiling water into the hole;
• add a quarter cup of dishwashing liquid;
• after 20 minutes, refill the liquid (it should also be boiling);
• wait 30 minutes and turn on hot water to thoroughly rinse the drain.

A plunger can be used with such a remedy. This cleaning will be more effective.

Sulphuric acid

Some people use this remedy if the contamination is very strong. However, it should be borne in mind that the acid is quite aggressive. Plumbers argue that this tool is not always effective, moreover, it can destroy sewer pipes.

Every day in the bathroom at least once water treatments... Gradually, various debris accumulates inside the pipelines and you have to think about how to clear the blockage in the bathroom. There are a lot of options for the clogging of the siphon or other water communications: human and animal hair, pieces of rags, grease, various pollution of the pipe system. Over time, the liquid leaves more and more slowly and a bad smell appears, which is emitted by the sink or bathtub. You have to do something about this.

What causes blockages?

The most serious reason for clogging a sink or bathtub is error during pipe installation. Making repairs, "craftsmen" are mistaken with the angle of installation of pipes for the sewage system, this, in turn, contributes to the occurrence of traffic jams. Cleaning in this case is possible, but pointless. The elimination of the problem must begin with dismantling the old pipes and reinstalling them.

The second more likely option is carelessness and neglect of preventive measures by the owners. Objects, hair and debris can easily clog the drain. Even with a slight blockage, it is recommended to get rid of it, so that the situation does not worsen even more. So how do you clear a blockage in your bathroom?

Ways to eliminate blockages

Mechanical tool # 1: plunger

If the hole near the drain is clogged, then take the object that most people have - a plunger. Then you should take a rag or cork and close the upper water drain hole so that there is no corridor for air. Then we lubricate the plunger rim with Vaseline, so we will ensure a tighter fit. We put the plunger on the drain, abruptly and intensively begin to drive out the pollution. It is quite possible that you will not be able to clean it the first time.

Mechanical tool no. 2: hot water plunger

If the previous method did not provide proper cleaning, then add hot water to it. We fill a third of the bath with water, pump it into the pipeline with a plunger, and then pull it out sharply. We continue until the drain is completely cleaned.

Mechanical device no. 3: rope

Doesn't take a plunger or hot water... What to do? Eliminate the blockage in the bathroom with a cable. Serious blockages can be removed with this tool. But keep in mind that it is possible to punch through thin plastic pipes if you are not careful.

It is quite easy to build a cable at home. To do this, you need to get a flexible metal wire. Then bend one of its ends in the form of a small hook, and wind the fabric to the second, making a handle.

Slide the attachment into the pipe to the expected clogged place and push through the debris. After removing the main part of the blockage with a rope, pull out the "fishing rod" with the rest of the dirt. At the very end, rinse the container with hot water.

Chemicals

In some cases, it is appropriate to use chemicals if the bathtub or sink is clogged. In stores, a large amount of chemistry is sold in the form of a gel, powder, liquid or foam, which can remove all the bad things that are stuck in the pipeline in a few minutes. Organic contaminants are ideal for chemical removal.

1. Before use, be sure to read the instructions included in the kit.
2. Use personal protective equipment to avoid unwanted consequences.
3. Buy products that dissolve hair.

Folk method number 1: boiling water

Traditional methods are no less popular and give good results. But, alas, removing a strong blockage in a sink or bathtub is impossible with the help of them. If the pipes or drain have accumulated a large amount of fat, then this can be corrected with boiling water. Just pour boiling water into the hole until the water starts to flow better.

Folk method number 2: vinegar and soda

Baking soda and vinegar react with each other, so they are able to remove more difficult pipe contamination. At the very beginning, the soda is poured into a glass, after which it is sent straight to the drain. Next, you should pour the vinegar into a glass and pour it into the drain as well and plug it with a cork. Foam will begin to form if the vinegar and baking soda react. After 15-20 minutes, rinse with hot water to rinse off any remaining vinegar and baking soda.

Folk method number 3: lemon

It is profitable to use folk remedies and it is convenient at home, but they do not always give the desired effect. But lemon will help get rid of light contamination of pipes. Squeeze the juice from one fruit into the sink and wait an hour or two. Over time, the sink or tub is rinsed with hot water.

How to clean the siphon?

The siphon must be cleaned periodically, but if you do not do this on time, problems can appear at the most inopportune moment. It is recommended that you rinse the siphon regularly so that the sink does not emit a bad smell. Now let's move on directly to cleaning.

Obtain an unnecessary soft cloth and place a container for water under the siphon. Open the fasteners and remove the flask. After all the water has drained out, gently clean the siphon. Then flush the device and install it back. Also, remember to position the nipple so that it does not rest on the bulb. Do not rush to clean the basin, first open the water. If nothing flows, then the siphon is installed correctly.

• Don't dismiss preventive measures... Doing them regularly will not waste a lot of time in the future.
• Install a metal mesh to collect any debris.
• In some cases, it will not be superfluous to use compounds that prevent blockages.

Now it became clear how to clear the blockage in the bathroom. After all, anyone agrees that it is pleasant and comfortable to be in a clean bath.