Almost every day has drill holes in stone... And this does not cause any particular difficulties when using special equipment. But what to do if you do not have experience and knowledge, and it is necessary to drill a hole.
I myself remember the first time I went to a hardware store and asked for help from a sales assistant. I needed to drill 2 small holes in a granite slab. The salesperson advised me of the victor tipped drills, assuring me that they fit perfectly.
Without going into the details of my first drilling holes in stone, I can only say that 3 drills that I purchased from this hardware store burned out, broke the edge of the hole being drilled, and if these holes were not technical, it would take a long time to fix the problem.
So. How can you drill a hole in the stone yourself and is it necessary for this?

Now on sale there are drills - diamond-coated crowns and they can be bought in almost any large construction market. The price depends on the thickness of the spray and the service life of the drill.

And if you need to drill one hole and two, almost any will do. And if you plan to frequently use such a tool, then it is best to purchase a crown in which the diamond is not sprayed, but pressed along the entire volume of the incisal edge.
The attachment of the crown is also different. You can use a drill or grinder. We use heavy cutting machines and a device for drilling holes in stone products, they have the same fastening as on a small cutting machine.
And now you have become the owner of a diamond-coated drill, what should you do next?
How drill a hole in the stone so that it is even and neat?

I think that 4 simple steps will guarantee you long service diamond core bits when drilling holes.

Step 1... When drilling holes in stone, use diamond drills at low speeds (revolutions). Small diamond drills should be used at about 1-2 speeds of your tool - that's about 700 to 1000 rpm.
Diamond drills should be used at varying speeds depending on their diameter.
6mm - 2000 rpm
12mm - 950 rpm
24 mm - 700 rpm
Step 2.
Drill holes in stone and other materials needed with water. Water prevents overheating of the cutting edge of the diamond drill, flushes the cuttings out of its pores. This, in turn, will extend the service life of the drill, protect it from jamming, as well as the stone itself will not overheat and the edge will remain neat.
In production, when drilling holes in a stone, water is automatically fed into interior drills are under pressure and the drill is constantly washed with water. it is not always possible to do this. To do this, you can make a "bath" around the hole to be drilled.

You can cut out the middle part from a plastic bottle and glue it with tape to a stone surface, fill it with water. While drilling the holes, raise the bit so that water can wet the cutting edge and enter the hole to be drilled.

Step 3.
If you have little experience, practice some trimming before you start drilling holes in the stone.
Make the markup. Draw a line on the stone. Often on polishing, a pencil practically does not leave marks, so you can use masking paper tape and make the necessary marks on it.
The first way, which is often recommended for drilling holes in stone.
First, start drilling the stone at a significant angle to drill out a small groove, then gradually flatten the crown until it is upright, while continuing to gently press on it. If you immediately press the diamond bit to the surface of the stone and start drilling, the drill will not stand still, but will "roll" over the surface and spoil it.
The drills are not always well centered, and if you have little experience in drilling holes in stone, then initially you may not hold the tool and spoil the polish, break the edge of the hole being drilled, and, finally, simply drill inaccurately.
There is a fairly simple second way for precise drilling of holes.
To do this, you can drill a hole in any cut of the stone, you can say practice.
Once the hole has been drilled and completely finished, it can be used as a template. Just simply attach to the product in which you need to drill a hole and clamp. Thus, the drill will move along the already drilled hole, it will not be hit and there will be a neatly drilled hole in your product. You can also add water there.
Step 4.

I have already mentioned this, but still decided to highlight it in a separate column.
Do not press hard on the crown while drilling holes. Diamond core bits are very sensitive to pressure and overheating. Lift it up periodically to keep it wet with water and cool.

Be patient and diamond drills will last much longer. Good luck!

Check out my Master Class "How to drill a stone":

It is possible to drill a hole in a stone as strong as granite, but it is necessary to thoroughly prepare for this difficult procedure. For drilling, you will need not only a drill for granite, but also a set of appropriate tools and accessories. The workplace should also be properly prepared.

Features of drilling granite

What is needed to drill stone (including granite)? Let's consider the stages of the procedure and preparation for it in more detail.

Preparation of the workplace

The working surface, on which the stone element will be laid for processing, must be not only strong and reliable, but also completely flat, and its dimensions must not be less than the dimensions of the workpiece. It is very important that none of the parts of the latter remain in weight.

Special tool with integrated coolant supply - a professional approach to natural stone drilling

Tools and supplies

To successfully drill granite, you need to prepare the following tools and consumables:

• electric drill;
• a drill bit of the required diameter, on the working part of which diamond spraying is applied;
• water.

To prevent the diamond drill, with which a hole will be formed in the granite, from slipping off the smooth surface, a depression must first be made at the processing site. For this purpose, you can use conventional drill for metal.

What is water for?

When wondering how to drill granite, it should be borne in mind that it is not easy to carry out such a procedure without using water as a cooling liquid. Cooling of the drill for granite during operation is mandatory, for this purpose it is necessary to supply water to the processing zone.

The simplest device for cooling a stone drill can be made from a plastic bottle by making several small holes in its cap. You will get a kind of spray that is very convenient to use during processing. It should be borne in mind that when drilling, water should always be at hand in order to be able to cool the heated drill at any time.

Having chosen a diamond drill according to the required diameter, which is optimal for drilling in stone (including such hard as granite), the tool must be fixed in the chuck of an electric drill. After that, you can start forming a hole in the workpiece.

An alternative to water cooling - a bit with a grease-like lubricant inside, which flows out during heating into the drilling zone

How is drilling done

How to drill a stone so as not to split it, but to form a high-quality hole in it? This question is asked by those who have never encountered the procedure before and are going to carry it out with their own hands. In such cases, it should always be remembered that the tool used must not be put into punching mode, as the shock load generated may cause the workpiece to split.

Making holes in stone (including drilling in marble) should be started at low speed of the tool, positioning it at a significant angle. After a small groove has been formed on the work surface, the position of the drill can be gradually leveled.

The drill pressure on the stone during processing should be small, while it is necessary to ensure that cutting tool did not damage the polished surface of the product. Do not forget that water must be constantly supplied to the drilled section of the hole in which the drill continues to work. Very often to do this important condition around the hole to be formed, a rim is created from the middle part of a plastic bottle, which is attached to the granite using ordinary tape. Water is poured into the inner part of such a side, the level and presence of which is constantly monitored. It is possible to use this simple device, which prevents not only overheating of the drill, but also the formation of stone dust, only when processing horizontal surfaces.

How else can you form a hole in granite?

A stone drill, with which a hole is formed in granite, can be made from a tube made of non-ferrous metal. This method, in comparison with the option in which diamond drills are used, is technically more complicated.

How to properly drill granite with a non-ferrous tube?

• Around the center of the future hole on the granite surface, it is necessary to form a side with a height of at least 5 mm, for which you can use ordinary plasticine or the middle part of a plastic bottle.
• It is necessary to pour diamond dust, corundum or victory powder into the inner part of the formed rim.
• Water is poured into a rim-shaped tray filled with abrasive powder. In order to constantly replenish the water level in such a bath, it is necessary to prepare a separate vessel in which it will be contained in sufficient quantity.

Drilling granite using this technique alone is problematic, so you need the help of another person who will make sure that the tub formed around the hole being made is constantly filled with water. Drilling with this technology is also performed at low speeds.

It is best to drill artificial stone with a drill, at the end of which there are hard alloy solders. In construction, such drills are used when drilling concrete. To make the work more productive, drilling is done with a hammer drill. Drilling with a hammer drill occurs due to the impact force of the drill.

To drill artificial stone, a perforator and small diamond-coated drills are used.

At the same time, the drill almost does not heat up, and the holes are drilled much faster.

Artificial stone can be drilled with a diamond drill. You can use a regular electric drill here. If you need to drill a thin hole, such as a small natural stone for decoration, a needle with a diamond tip is used. This is done on a drilling machine.

If a hole is required large diameter, an artificial drill is drilled with a crown. The bit, like the drill, has carbide taps. In construction, such drilling is done in load-bearing concrete walls. This is done when it is necessary to lay plumbing or ventilation pipes. It is necessary to drill the material with a bit, which has a large diameter, only at low speeds. While drilling on carbide brazing crowns must be served cold water... This is necessary so that the soldering does not overheat. V otherwise they will fail ahead of schedule.

The main tools for drilling stone are:

• tungsten carbide drill;
• serlo with diamond plating;
• tungsten carbide crown;
• puncher;
• diamond tipped needles;
• drill.

In the event that it is necessary to drill large holes in stones, it is used special equipment... So, in order to drill them under the communication pipes, such equipment is mounted on a monolithic concrete wall... So that the stone is not damaged working surface the crowns, cold water is supplied to it with the help of hoses.

Drilling technology

The processing of solid materials is associated with the use of a certain technology. Drilling stones has its own specifics. For example, granite is a very hard and at the same time very brittle stone. When choosing the rotation speed of the tool, you need to proceed from the diameter of the hole to be drilled. How larger diameter you need a hole, the less revolutions are required.

To make the hole in the right place, you need to make a small groove by tilting the rotating drill to the side.

During drilling, the water supply must be mandatory. Water, firstly, protects the cutting edges of the diamond drill from overheating, and, secondly, flushes out the cuttings. Before starting drilling, in order to get the hole in the right place, you need to tilt the rotating drill to make a small groove. The drill is then leveled and smooth drilling begins at this point. This is necessary so that at the very beginning the drill does not move out of the set point.

The drill must be well centered to avoid damaging the edges of the hole. The object to be drilled must be on a level surface and well fixed. Unlike concrete, it is undesirable to drill granite in perforation mode. It is very fragile and can crack in shock mode.

When drilling granite, proceed from following parameters hole diameter and drill speed. With a hole diameter of 6 mm, the rotation speed should be 2000 rpm. With a hole - 12 mm, rotation speed - 950 rpm. If the hole is 24mm, the rotation speed should not exceed - 700 rpm. Such data are obtained empirically and are the most optimal.

In some cases, granite needs to be reinforced. Such a need arises when a tabletop is made from a relatively thin sheet of granite. A large load on the table surface can break it. To increase the strength of a granite slab, it is reinforced with a steel bar.

On inner surface plates with a grinder and diamond wheel an even groove is made. The depth and width of the groove should be 1 mm larger than the steel bar. After removing dust from the groove, a steel bar is placed in it. The rod laid in the groove is filled with superglue. After the glue hardens, the strength of the reinforced granite slab will be increased several times. This has also been established empirically.

One important part of the laboratory is furniture. Each laboratory in which chemical, biological, medical research will be carried out must have appropriate furniture. Special tables, cabinets, cabinets, tables and cabinets are all an integral part of the laboratory.

For a person who has practically no idea how the process of work in a laboratory takes place, it is completely unclear why regular table or the chair is not suitable for this. But in fact, furniture plays a huge role in the laboratory, which is why household furniture cannot be in the laboratory.

What are the basic rules for laboratory furniture?

The most basic rule for laboratory furniture is that it must be ergonomic and practical. Experiments and investigations of a different nature should be carried out in a comfortable and well-planned environment. Different decor in such rooms is categorically unacceptable.

The second rule says that a table or some kind of cabinet, whether it is pull-out or not, should be simple and multifunctional. For any business, there must be certain furniture that will be responsible for a particular task. For example, drying cabinet must be used only for drying.

The third rule is: laboratory furniture in moscow must be very durable, since it has to withstand not simple loads. The strength of such furniture should be the highest level as a rule, laboratory furniture must be crack-resistant. Often, such furniture is made from durable material such as plastic, metal or glass.

Where to buy laboratory furniture at affordable prices?

LLC "Innogen" is engaged in the sale and production of laboratory furniture. Today, the production of this company is in high demand in all CIS countries. Production room located on the territory Russian Federation, namely in the city of Pskov.

For the production of laboratory furniture, only high-quality and durable equipment for metal processing and painting is used. It must be said that the laboratory furniture of the "Expert" brand has received a quality mark, and is also fully certified in accordance with all the requirements of GOST in Russia.

All about roofing and roofs. Verified and latest materials, technologies, design developments in the production and installation of roofs and roofs in housing construction

000666

Sverlit kamen. How to independently drill a hole at home in any natural or artificial stone with your own hands. Techniques and technologies for drilling stones or how and how to drill stones yourself

Today we will talk about how to independently drill a hole at home in any natural or artificial stone do it yourself. We will also consider the methods and technologies of drilling stones, or how and how to drill stones yourself

How to drill a hole in the stone yourself and what tool is needed for this?

Now on sale there are drills - diamond-coated crowns and they can be bought in almost any large construction market. The price depends on the thickness of the spray and the service life of the drill.

And if you need to drill one hole and two, almost any will do. And if you plan to frequently use such a tool, then it is best to purchase a crown in which the diamond is not sprayed, but pressed along the entire volume of the incisal edge.

The attachment of the crown is also different. You can use a drill or grinder. We use heavy cutting machines and a device for drilling holes in stone products, they have the same attachment as a small cutting machine.

And now you have become the owner of a diamond-coated drill, what should you do next?
How to drill a hole in the stone so that it is even and neat?

I think 4 simple steps will guarantee you a long service life for your diamond core bits when drilling holes.

Step 1. When drilling holes in stone, use diamond drills at low speeds (revolutions). Small diamond drills should be used at about 1-2 speeds of your tool - that's about 700 to 1000 rpm.

Diamond drills should be used at varying speeds depending on their diameter.
6mm - 2000 rpm
12mm - 950 rpm
24 mm - 700 rpm

Step 2.
It is necessary to drill holes in stone and other materials with water. Water prevents overheating of the cutting edge of the diamond drill, flushes the cuttings out of its pores. This, in turn, will extend the service life of the drill, protect it from jamming, as well as the stone itself will not overheat and the edge will remain neat.

In production, when drilling holes in a stone, water is automatically supplied to the inside of the drill under pressure and the drill is constantly washed with water. It is not always possible to do this at home.

To do this, you can make a "bath" around the hole to be drilled. You can cut out the middle part from a plastic bottle and glue it with tape to a stone surface, fill it with water. While drilling the holes, raise the bit so that water can wet the cutting edge and enter the hole to be drilled.

Step 3.
If you have little experience, practice some trimming before you start drilling holes in the stone.

Make the markup. Draw a line on the stone. Often on polishing, a pencil practically does not leave marks, so you can use masking paper tape and make the necessary marks on it.

The first method is often recommended when drilling holes in stone.
First, start drilling the stone at a significant angle to drill out a small groove, then gradually flatten the crown until it is upright, while continuing to gently press on it. If you immediately press the diamond bit to the surface of the stone and start drilling, the drill will not stand still, but will “roll” over the surface and spoil the polish.

The drills are not always well centered, and if you have little experience in drilling holes in stone, then initially you may not hold the tool and spoil the polish, break the edge of the hole being drilled, and, finally, simply drill inaccurately.

There is a fairly simple second way to drill holes accurately.
To do this, you can drill a hole in any cut of the stone, you can say practice.

Once the hole has been drilled and completely finished, it can be used as a template. Just simply attach to the product in which you need to drill a hole and clamp. Thus, the drill will move along the already drilled hole, it will not be hit and there will be a neatly drilled hole in your product. You can also add water there.

Step 4.
I have already mentioned this, but still decided to highlight it in a separate column.
Do not apply too much pressure to the bit while drilling holes. Diamond core bits are very sensitive to pressure and overheating. Lift it up periodically to keep it wet with water and cool.

Granite is the most difficult material to process. It is a very hard, but at the same time quite fragile stone. Therefore, the work associated with drilling holes in granite must be carried out very carefully and accurately. In order for the granite stone not to split during drilling, it is very important to follow a number of simple rules.

Several must-have recommendations for drilling granite.
Drilling of granite must be carried out at low revs (speeds) of the drill. Small diamond-coated drills should be operated at first speed, maximum at second speed. It is important to note the fact that the drills are used at variable speeds depending on their diameter. So if you use a drill with a diameter of six millimeters, you need to work at two thousand revolutions, if the drill diameter reaches 12 mm, then you need to set nine hundred and fifty revolutions on the device, and if you use a drill with a diameter of twenty-four millimeters, then you need to work at speed seven hundred revolutions per minute.

It is imperative to drill granite with water, as it will prevent overheating of the cutting edges of diamond drills, as well as wash out the sludge from its pores. When drilling granite with water, you will thus slightly extend the life of the drill and prevent it from jamming. Also, the granite will not heat up too much when drilling and the edges of the hole will be clear and neat. Nowadays, in production, when drilling holes in stones, water is automatically supplied under pressure to constantly wash the drill.

If you've never drilled granite before, practice on some shard or trim before starting. Before you start drilling granite, make a markup by drawing a line on the surface of the stone. It is best to do this with paper masking tape, since a simple pencil very often does not leave the slightest trace on the polish.

Currently, the most commonly used two methods of drilling granite:

How to drill granite, method one: start drilling granite at a slight angle so that a small groove is drilled first. And then smoothly align the crown to a vertical position. If this is not done, the drill will "ride on the surface".
Drilling in granite, method two: in practice, there are often cases that the drills are poorly or not accurately centered. And if you have no experience in drilling, you may not willingly spoil the polishing of granite, damage the edge of the hole, or drill it completely inaccurately. Therefore, the second method is that you first drill the same hole on a small piece of granite. And if you succeed, then you can now apply it as a template. To do this, you just need to attach it to the desired area of ​​granite and clamp it. The drill will no longer roll over the surface. Water will also need to be supplied there.

How to drill a hole in granite step-by-step instruction.
To drill a hole in granite, you need an electric drill that can be adjusted to the number of revolutions. You will also need a diamond core bit of the required diameter, copper tube or victory glass, water, a semicircular file, and perhaps you will need diamond dust or win.

Before you start drilling, position the granite workpiece as conveniently as possible and secure it. The granite stone must lie completely on a level and flat surface.
Scratch the center of the intended hole with a metal drill. it important point which will prevent the drill from sliding on the granite surface during operation.
Fix the crown of the required diameter in the electric drill. It must be diamond coated. Otherwise, you will not be able to drill the hole.
Only drill a hole in the granite at low RPM and never turn on the perforation mode. Failure to comply with this condition can provoke granite splitting or cracking.

During the entire process of drilling granite, add water regularly to the hole you are drilling. This can be done using the usual plastic bottle, in which you first need to drill a hole. Perfect option when you bring in a second person to fill up the water so you can concentrate entirely on drilling the granite. It is very important that the drill does not "float" in the liquid.

Why use water when drilling granite:

· You will not apply unnecessary effort for drilling;

You will save the drill for subsequent work, extending its service life

· You, thus, relieve granite from overheating.

How to drill granite without a diamond core bit.

If you do not have a diamond crown, you can get out of the situation like this: make a plasticine ring around the circumference of the intended hole. Its height should be three to five millimeters. It is necessary to pour a small amount of corundum, diamond dust or win into it. A small tube made of copper or any other non-ferrous metal, such as brass, needs to be fixed into the drill. Then you can start drilling at low speeds and without perforation. Do not forget to supply water during operation, which in this situation will cool the tube.

And if you do not have both a diamond core bit and a non-ferrous metal tube, you can try drilling granite with a victorian drill. But only in this situation, drilling must be carried out immediately at high speeds, constantly supplying water. As soon as you feel that drilling is not taking place, immediately take out the drill and sharpen it with a semicircular file.

Sharpening must be done with extreme care so that the cutting teeth do not overheat under any circumstances. Otherwise, they will immediately become soft, and dull even more quickly. It is noticed that when drilling granite with a drill from a victor, sharpening should be done after every 20-40 seconds of drilling.

As you can see, drilling granite is not an easy task, as it requires certain skills, knowledge and skills. So, when you get to work, be sure to practice on the granite scraps, and only then get down to business!

More posts tagged "stone processing"

Cut the carnelian in an instant!

The easiest way to cut a gemstone. Of course, you can't cut a stone instantly, you just split it. But small samples of minerals, ...

Rhinestone

The lenses are crystals. Stone processing. I continue to work with rock crystal crystals. I decided to leave some of the minerals in the same form as ...

Manually. The simplest processing of minerals.

Grinding. Jet. The way of processing stones, old as the world, is simple and accessible even to a child. Does not require special equipment and tools, ...

Algiz on the jet

Jet with the Algiz rune Carved out a new amulet: Height - 3 cm Thickness - 8 mm Weight - 3 g Cord hole Price - $ 30 or at a commercial rate in ...

Playlist for stone processing. Review of engravers.

I decided to create a playlist - "Stone processing, gems". Engravers, etc. Mineral lovers and collectors sooner or later start on their own ...

How to cut jet at home

Processing minerals at home Few handmakers have serious stone-cutting equipment at home, but those who are carried away are so ...

Sometimes such situations arise when working with stones, when it is necessary to make a hole. Of course, when you have at hand necessary equipment it is much easier to do this and does not cause any inconvenience at all. Unfortunately, such equipment, in the right moment may not be at hand, but this hole is so necessary. For this case, you can use the advice provided and do it yourself.

Choice of tools

First, you need to choose special equipment in order to make a hole in the stone. In this case, a diamond drill is the best choice. It is important to remember that a classic drill, which has a victorious tip, is not suitable for such purposes, but they are sold at every step by construction market... At the same time, the drilling quality will be at the lowest level. In addition, such equipment can even ruin the work, and the required hole will not be made. Using such a tool, it quickly burns out and breaks the edge, and this is not a feasible result and a good option.

Diamond drill

Today, diamond drills are provided on the world market that are able to cope with such a task without any problems. Such a tool also has another name - a diamond core bit. Using such equipment, you can make a hole in the stone of any diameter that the master needs.

Why is a drill called a diamond drill? This is due to the fact that the tip has a diamond coating. It is because of him that the work is greatly facilitated, while making the hole clean and even. As for the cost, it will depend on the thickness of the spray, as well as the service life of the drill.

Any diamond bit can be used to make multiple holes, although there are exceptions. For frequent use of the tool, it is best to purchase a drill that was made by means of heat sintering. This method implies a rigid bond between the drill body and the granules. Such a tool is a significantly higher resource when compared with crowns, the manufacturing method of which is diamond sputtering.

The tool also differs in the way the crown is attached to the tool. Mounting is made, both on the grinder and on the drill, if, of course, there is a tail with external thread and internal M14. Fastening is carried out on a special installation that produces diamond drilling.

After the tool has been selected, you need to start drilling a hole in the stone. But in order for the hole to be neat and even, it is necessary to use well-developed techniques.

Hole drilling technique

In order to drill a hole in the stone, you must use water. This action is necessary because the water cools the cutting edge, thereby preventing it from overheating. Thus, the diamond drill will work much longer, and all sludge will be washed out of the spores. In this case, the edge will not jam, and the stone will not overheat during drilling, which is guaranteed, will give a neat and clean edge.

For example, companies that process stones have special installations. Diamond drilling is done automatically, as well as the water supply. This happens through the inside of the device. In this way, the edge is constantly cooled and the drill is cleaned. When drilling at home, you can organize a bath that will be located around the hole, and thereby simultaneously cool the edge. So when drilling, you only need to raise the tool so that water constantly gets into the hole and on the edges of the drill.

When punching holes in the stone, it is best to install the most low speed tool. Drill small size which are manufactured using diamond spraying technology, when drilling, they should operate at a speed of approximately 700 to 1000 revolutions per minute.

For example, the crowns, which were made using thermal sintering technology, operate at a speed that is constantly changing, depending on the diameter. So for hole diameters:

At 4 millimeters, the speed should be between 1900 and 2100 rpm;
At 10 millimeters, the speed should be between 900 and 1000 rpm;
At 22 millimeters, the speed should range from 650 to 750 rpm.

Preparing to drill a hole

With minimal or no experience in drilling in stone, before starting work, it is best to train on some other pruning.

The best place to start is to do some markup. Pencils very often become invisible on the stone, so it is best to leave marks with masking paper tape on top of which the marking will be made.

The drilling starts at a significant angle, by means of which a small groove is drilled. Gradually, you need to align the crown so that it acquires a vertical position, while you should not press hard on it. In the event that you start to press on the diamond drill, while pressing harder against the stone, the tool will begin to move and ruin the surface.

With a little experience working with a drill, you can spoil the polishing of the stone, since it can be very difficult to hold the tool in your hands. In this case, the edges of the hole are broken, and the drilling is not carried out exactly in the intended place.

What should be laboratory furniture?

One important part of the laboratory is furniture. Each laboratory in which chemical, biological, medical research will be carried out must have appropriate furniture. Special tables, cabinets, cabinets, tables and cabinets are all an integral part of the laboratory.

For a person who has practically no idea how the process of work in the laboratory takes place, it is completely incomprehensible why an ordinary table or chair is not suitable for this. But in fact, furniture plays a huge role in the laboratory, which is why household furniture cannot be in the laboratory.

What are the basic rules for laboratory furniture?

The most basic rule for laboratory furniture is that it must be ergonomic and practical. Experiments and investigations of a different nature should be carried out in a comfortable and well-planned environment. Different decor in such rooms is categorically unacceptable.

The second rule says that a table or some kind of cabinet, whether it is pull-out or not, should be simple and multifunctional. For any business, there must be certain furniture that will be responsible for a particular task. For example, an oven must be used only for drying.

The third rule is: laboratory furniture in moscow must be very durable, since it has to withstand not simple loads. The strength of such furniture must be at the highest level, as a rule, laboratory furniture must be resistant to cracking. These furniture are often made from durable materials such as plastic, metal or glass.

Where to buy laboratory furniture at affordable prices?

LLC "Innogen" is engaged in the sale and production of laboratory furniture. Today, the production of this company is in high demand in all CIS countries. The production facility is located on the territory of the Russian Federation, namely in the city of Pskov.

For the production of laboratory furniture, only high-quality and durable equipment for metal processing and painting is used. It must be said that the laboratory furniture of the "Expert" brand has received a quality mark, and is also fully certified in accordance with all the requirements of GOST in Russia.