Sawing logs into planks with a chainsaw. Techniques for cutting logs on a band sawmill How to cut a log with a diameter of 6 cm

What you can't do with a chainsaw - with the help of all kinds of attachments, this tool becomes very multifunctional. Not sure how to cut a log into planks with a chainsaw? Now and not about this we will tell!

Chainsaw - a tool for all occasions

Most owners have no idea what possibilities are hidden in this seemingly single-function tool. It's about what functions, in addition to sawing logs for firewood, a chainsaw can perform in skillful hands... But just think - the tool is completely autonomous, you put fuel into the tank, and work wherever it is convenient for you!

A wide range of work leads to a powerful, compact and safe gasoline engine, which has a very unpretentious "character" and the ability to work in the most difficult conditions. Another good thing about a chainsaw is its sealed fuel supply system, which, in combination with a membrane type carburetor, allows it to work in a variety of positions, except perhaps inverted. In addition, the designers provided reliable protection nodes from overloads and breakdowns in the form of a centrifugal clutch.

Take a look at the chainsaw from a different point of view - you are holding an amazing tool in your hands! After all, this is a universal drive for the most different kinds devices capable of not only sawing wood, but also cutting metal and stone, pumping water, drilling wells and even serving as a low-power engine!

DIY multi-tool

The most popular attachment, which is even produced by the manufacturers of chainsaws themselves, is the gas cutter attachment, which turns the chainsaw into an autonomous semblance of a grinder. The device of the nozzle is a bearing unit with a shaft, with a pulley installed at one end, which is driven in rotation by a V-belt. At the other end is a mandrel for attaching abrasive wheels. By changing circles, such a Bulgarian chainsaw will be able to cut stone, tiles, bricks and even metal. Of course, the circle is hidden in a protective casing, without which the work of such a tool would be pure water playing roulette - lucky or not!

Of course, there will be a lot of people who would call this method extravagance, because you can buy a normal one and not have to worry about changing any attachments there! However, in practice, the idea is completely justified - high-speed saws equipped with such attachments work just as well as ordinary grinders. Of course, they do not compete with professional powerful tools, but they justify themselves on the farm. This device has two indisputable advantages - autonomy and saving money.

Another professional attachment that you can buy in specialized stores is the so-called debarkers. Their functions just correspond to the purpose of the chainsaw and, in fact, increase its capabilities - in addition to cutting wood with the help of debarkers, it can be processed, namely, cleaned of bark, growths and twigs, as well as cut grooves in logs, which is useful in the construction of wooden log cabins. and give the rounded surface a flat shape.

Debarkers are divided into disc and drum. The first ones are used to cut out recesses and mounting grooves, and the drum ones are used to remove bark from logs, they are also called debarkers. The device is a drum or cutter fixed in a bearing assembly. The device is set in motion by means of a V-belt transmission, for this there is a special pulley on the axle. Taking into account the change in the diameter of the pulley and the speed of the engine, you can also change the speed of such a tool for optimal wood processing.

With the help of a chainsaw and the corresponding attachment, you can not worry about emergency water supply at home if necessary - you can make a pump from this woodworking tool in a few minutes!

Basically, the nozzle is a conventional centrifugal pump that attaches to the saw and is powered by the same pulley and belt. The principle of operation is the same as for everyone centrifugal pumps- one hose is lowered into the water, the second serves as a pressure hose. Before starting work, liquid is poured into the engine through the plug, which is necessary for the pump to "grab" the pumped-out water. The turbine, when rotating, creates a reduced pressure inside, due to which water is pumped out. The device is, in fact, the simplest, but imagine what use it can be when Vacation home de-energized, and the issue of water supply needs to be resolved urgently!

With the help of special attachments, the chainsaw can be turned into a drill or a winch and even into a boat motor capable of speeds up to 20 km / h with a fuel consumption of 1 l / h. However, these are already more rare cases, while devices for longitudinal sawing of logs, or, as they are called, mini-sawmills, are quite common.

How to cut a log into planks with a chainsaw - vertical nozzle

First of all, it should be noted that no one sets himself the task of making a professional sawing of a log with a minimum amount of waste. For professional work the appropriate tool is also needed, however, the nozzle for longitudinal sawing of logs will allow you to solve a lot of minor problems... Suppose, for example, that your garden has withered old pear, and you just needed a few planks to fill a hole in the barn. Instead of putting the trunk of a tree on firewood, you can use a nozzle to get the material you want.

Devices for longitudinal sawing of logs are divided into vertical and horizontal. Most simple device is the first option: the adapter is attached to the bus at its base, and with the help of the guide bar, the straightness of the adapter movement is ensured. This whole structure is attached to the board, which is a stop for cutting and at the same time a guide. The accuracy of such a device is not high - it can be used to cut rough boards or give a log an uncomplicated square shape, however, appropriate tasks are set for such a device.

How to cut a log lengthwise - we cut horizontally!

Much greater cutting accuracy is provided by the horizontal design, which is a rigid frame attached to the chainsaw bar in two places - at the base and at its end. The attachment points can be shifted to provide the required kerf width. Of course, such a device is intended for small logs, the diameter of which will not exceed the length of the bar.

Using the guide element, you can install required thickness boards. The most difficult thing will be to make the first horizontal cut - in order to get an even cut of wood, you need to attach an additional guide frame to the log, which will serve base surface for emphasis. At the subsequent stages of dissolving the log onto the boards, the flat surface of the previous saw cut serves as a surface for an emphasis and a guide.

It is quite easy to work with such a structure. Before sawing a log lengthwise, it must be well secured along its entire length - the less it vibrates, the smoother the cut will be.... To avoid jamming the chainsaw bar, small wedges are constantly inserted into the cut to prevent clamping. It should be noted that no matter how hard we try, there will be a lot of waste compared to a conventional sawmill. First, give the log a square shape by sawing upper layer from all sides, and only then proceed directly to dissolving the logs onto the boards.

It will not be difficult for craftsmen to make their own nozzles of this kind to work with welding and metal - the corresponding schemes on the Internet are not uncommon, and from the material you will need several square hollow pipes, nuts and screws.

Planks and beams are one of the main building materials. Funds do not always allow you to buy ready-made boards. Many have the opportunity to take a plot in the forestry and harvest timber on their own.

Sawing of logs is carried out using a sawmill, an electric or chainsaw and additional devices. When choosing tools, focus on the amount of work.

The cheapest stationary sawmill with all the accessories will cost you no less than 150 thousand rubles. If you do not plan to be engaged in a small business, the purchase of such equipment is inappropriate.

A more affordable tool is a chainsaw. A chainsaw is more convenient than an electric one for several reasons.

Electricity is not required for work - this allows you to work with a chainsaw on plots.
Has a higher power than electric.
Has a smooth start and convenient speed control, which reduces the risk of chain breakage.
The overrun brake is faster than an electric saw.
Long operating time without interruption - up to 1 hour.
Allows you to work in high humidity conditions.

Devices for fixing the log, a special frame-attachment for the chainsaw and a guide will help to cut the log along the chainsaw.

When sawing with a chainsaw, the tool is exposed to a lot of stress. A household chainsaw will quickly fail. Better to use a professional tool. A good option- Chainsaw Stihl MS 660 or Stihl MS 880. These models have a power of more than 7 horsepower, which is enough for continuous operation at heavy loads.

A special metal frame is attached to the saw bar. The distance between the frame and the tire is adjustable, which allows you to cut the material into boards of the required thickness.

Having at hand metal corners or legs from a school desk, make a frame as you can on your own.

The video shows how to make a frame with your own hands.

When working in stationary conditions, a rigid metal profile or a long flat board is suitable for the guide. The ends of the guide are fixed on the trestles, the log is laid from below. This method is only suitable for cutting short trunks - there is a possibility of guide deflection. This will result in uneven cutting of the trunk.

How to cut a log lengthwise

To make a smooth cut, you need a straight template - a leading ruler or guide.

The BigMill Timberjig mini sawmill (Logosol) is a good help in the work. Manufacturer Sweden. The cost of such a set is considerable - about 9,000 rubles. Calculate how profitable it is for you to purchase such a tool. The ability to cut logs at the site will help reduce transport costs.

Sawing is done with a two-stroke saw with two nuts for mounting the bar. The device allows you to fix and cut a log up to 60 cm in diameter.

In order to cut the log into planks, you will need a ripping chain. If it is impossible to buy such a chain, sharpen the usual one at an angle of 10 °. Do not forget that the chain loses its sharpness during operation and needs periodic sharpening. A well-sharpened chain will make your work easier.

The kit contains accessories and parts with which you can install a wooden rail. The frame fixed to the chainsaw slides along the guide and does not allow the tire to go to the side.

Operating procedure:

How to cut a log across

If you plan to cut the trunk across, and then dissolve the logs into planks, this is impractical. Usually a log intended for harvesting firewood is cut across.

A log sawn across is often used to make garden benches and tables. Look nice garden paths, decorated with a sawn tree .. In this case, sawing is performed into discs with a thickness of 10-15 cm.

Place the log on a strong, stable trestle with a height of 60-80 cm.
If you plan to remove the bark of the tree, do it before starting the cut.
Make a shallow cut to serve as a guide groove.
Rotate the log 90º so that the saw bar follows the groove.
When cutting logs into logs, first make notches with an ax.
Cut the log. Further processing of the material depends on the area of its application.

Safety rules for sawing wood

Wear headphones, goggles, a respirator, gloves, and heavy clothing.
Keep children out of the work area.
Have a first aid kit on hand - circular saws and chain saws are hazardous tools.
Do not use disk electric saw without protective cover.
Do not put fuel into the hot tank of the chainsaw, wait until it cools down a little.
Start the chain saw on the ground with the chain brake applied. Only release the chain brakes before starting to cut.
While working, hold the saw by the handle of the arc, pushing it forward along the guide. Do not push hard on the saw - it should move freely.
When pruning trees with a chain saw, take care of the ladders - the saw must not be lifted above shoulder level during operation.
If you are not left-handed, place the log on your right side.

How to cut a log correctly. Video lessons.

Working with the Timberjig sawing system.

More recently, a chainsaw was only used to cut logs across. Craftsmen could use it to make boards, rectangular bars, all kinds of wooden sculptures. For the townsfolk, this was not half the strength. Experience, skill and talent were required. Today, chainsaw manufacturers offer various attachments as an addition, which have turned the tool into a universal device with which you can cut not only wood, but also others. Construction Materials for example a stone. In the article, we will deal with one question - how to cut a log into boards using an ordinary chainsaw.

To cut a log you will need special nozzle in the form of a metal frame, which is connected with two bolts to the body of the gasoline saw. The junction is the bolts that secure the working body (tire) inside the tool itself. The nuts must be unscrewed, the frame must be installed on them, the nuts that come with the frame must be screwed onto the bolts. They are wider, which increases the clamping area, increases the reliability of the frame fastening to the chainsaw body.

Such a nozzle can be made with your own hands from shaped pipe... The main thing is the accuracy of the frame dimensions.

Cutting technology

One frame-attachment in the process of cutting logs into boards is indispensable. Because it needs a support, especially when sawing the upper part of a log with bark. That is, when the operation of turning a log into a bar is carried out. You will need an additional device made of two boards.

Two boards 40-50 mm thick are fastened together so that they are in perpendicular planes. The device is attached to the log with self-tapping screws, from the ends it is propped up with additional stops from the same boards. In this case, the fastening is made so that the upper rib vertical board was below the top edge of the log. That is, the distance between the edges determines the thickness of the slab to be cut.

It remains to install the chainsaw so that one part of the frame rests against the transversely installed board. This will be the support. The main plane of the frame will abut against the vertically installed part of the fixture.

The chainsaw turns on, the log is cut along with the set cutting thickness. The main task of the contractor is not to overload the tool with hand pressure. The saw, or rather the chain, will cut itself, you need to push it a little. After cutting the slab, the wooden device is dismantled, the log is rotated 90 °, the support installation is installed, the whole cutting process is repeated.

Attention! Wooden device used only for cutting slabs.

As soon as the log turns into a bar, you can cut it into planks without using a wooden device. Beam - lumber with rectangular section, it has four external smooth surfaces on which you can rest the chainsaw with the frame. You just need to press the frame against the cutting plane and move the tool along the workpiece. On the frame there is a thrust element located perpendicular to the entire structure, displaced across the cut. With its help, the thickness of the board to be cut is set.

To understand how logs are cut into boards with a chainsaw using a frame nozzle, watch the video below.

Another variant

There are similar attachments on the market a large number of... All of them are suitable for sawing logs into planks, they all have a similar design. But there are also differences. The photo below shows attachments for a chainsaw, which does not require additional attachments or tools to work with. In fact, this is a miniature hand-held sawmill, which is based on a gasoline saw.

The design is complemented by guides and wheels that move along the surface of the log, reducing drag. There are two pairs of wheels, they are located on opposite sides of the workpiece. It is convenient, easy, plus - the quality of the cut material increases.

The attachment is attached to the chainsaw in the same way as in the previous case. The main requirement for work is to accurately position the saw so that it is in a horizontal position. And although the oblique cut is the same, it is more convenient and easier when the tool is aligned.

Homemade nozzles

Masters have long learned to do a lot with their own hands. There is a huge variety of frame structures on the Internet that allow a chainsaw to cut logs into planks. there is simple options manual type, there are large complexes of the bed, guides with the help of which the tool moves or the log is raised / lowered. One of them in the video below:

Please note that the structure is assembled from metal profiles, which makes it reliable and stable. At the same time, the machine (it simply cannot be called in another way) is equipped with mechanical gearboxes that simplify the processes of moving the workpiece barrel and the chainsaw. No effort with your hands, just twist the handle from the gearbox. In this case, the thickness of the boards is adjusted by raising the log, and not with a gasoline tool.

Another option is a nozzle, which helps to make a cut not in a horizontal plane, but in a vertical one. The design is simple, but it is more difficult to work with it, because you have to make an effort to hold the chainsaw. In addition to the device, it is necessary to prepare a bar made of metal or a board, which is attached to the log in the longitudinal direction. It is on it that the nozzle frame rests when cutting is carried out.

In addition, this option is more dangerous, because nothing holds the board to be cut. She can hurt her leg when she falls. So the process must be carried out carefully. The video below clearly shows how this option works.

Another installation, which the manufacturer called the carriage. For this, such a frame structure was made from a profile pipe and several wheels, which will give the device some mobility in terms of moving the workpiece along the barrel. They are also a kind of stops that do not allow the chainsaw to move from side to side.

In addition to the carriage, use the usual aluminum ladder acting as a guiding element. It is attached to the log with clamps for nails or self-tapping screws.

Please note that the width of the ladder must match the distance between the carriage wheels located at different ends. The ladder must be placed horizontally building level... Aligned underneath different thickness pieces of boards.

The prepared chainsaw with a carriage is installed on the ladder. Turn on the engine and push it with your hands along the workpiece, cutting off its upper part.

The process is better seen from the side. Here you can see a carriage with wheels, a ladder, a log lying under it, how the cutting process is carried out.

Fixture design of this type difficult enough. But out of many homemade options manual type it is better, more convenient, more reliable. Now it is possible to adjust the height of the cut horizontally, pre-setting the ladder along the horizon.

Generalization on the topic

As it turned out, an ordinary chainsaw is a universal tool. If you choose the right attachment, it can replace a large number of instruments. Moreover, some nozzles are easy to make with your own hands, the benefit of their design can be found in the public domain. The internet is replete with variations.

Beams and planks are common materials used in house construction. In the absence of funds for finished materials, you can make them yourself using a chainsaw. Before you cut a log into planks with your own hands, you should learn more about the features of this process.

The advantage of sawing logs with a chainsaw

Sawing into planks can be done with tools such as an electric chainsaw and accessories designed to make the job easier. When choosing certain products, it is necessary to focus on the volume of the proposed work. Stationary sawmills are expensive and are purchased only if you plan to organize a business to create boards.

The most accessible tool for work is a chainsaw. Such devices have several advantages over electrical ones:

the chainsaw can be used anywhere, regardless of the presence of an electrical network;
the tool is suitable for working in high humidity conditions;
professional chainsaws are much superior to electric ones in power;
you can use the chainsaw continuously for an hour.

For sawing logs into boards together with a chainsaw, a special frame is used, which is fixed to the device and allows you to create boards of the same thickness. You also need a device to secure the log in one position. In addition, you will need a guide.

Since household gasoline saws are not designed for heavy loads, it is worth using for sawing logs professional tools... When choosing, you should pay attention to devices with a capacity of more than 7 horsepower. Before work, the fixed frame is adjusted in accordance with the selected width of the boards. To create a frame, you can use the legs from a school desk or metal corners.

Types of working attachments

The choice of attachments for work depends on the volume and type of work being done. The following devices are used with a chainsaw:

drum debarker, which is necessary for removing bark from logs;
lightweight nozzle for sawing logs;
a standard nozzle used for making boards.

Rip saw attachment

When using such a nozzle, the sawing occurs in the horizontal direction. It is fixed to the rail with special clamps and allows you to create boards of equal thickness. After the work, the boards are dried, and after that they can be used in construction.

Lightweight nozzle

Such devices are often used, but they should only be used when boards are being created for fences or sheds. This is due to the fact that the attachment of the nozzle on the tire occurs only on one side.

Lighter

The nozzle for removing bark from logs is applied due to the wedge transmission. Attachment takes place with belts - special pulleys are used for this. It is worth noting that the performance of the nozzle can be changed, since the speed of rotation of the shaft depends on the size of the pulleys.

Features of sawing logs when using a chainsaw

It is quite simple to create additional equipment for sawing logs:

To create a support, a frame is used, which can be created from the legs of a school desk. The most suitable are pipes with a square section of 20 × 20 mm.
When constructing the frame, it is necessary to create 2 clamps, and fix the cross member at one end. This element must have holes for the tie bolts. A projection for the tire is created in the middle
In order to cut a log lengthwise, it is necessary to design a support frame, the width of which should be at least 8 cm in length.
For ease of use, a handle should be welded to the frame.
Before starting work, you must carefully check whether the frame is securely attached to the tire.

Use homemade tool simple enough. Before sawing, you need to install 2 trestles - they will be used as a support for the log. In addition, a metal rail or flat board is being prepared, which will serve as a guiding element.

Sawing technique along

The most difficult step in the process is making the first cut. For this you need:

install a guide ruler, which consists of two boards that are fastened together at an angle of 90 degrees;
after that, it is necessary to place the log to be sawn on the supports and fix it;
then it is important to check if the log is level;
at the next stage, it is necessary to fix the leading ruler on the supports using self-tapping screws;
after that you can start creating the first saw cut.

Cross cut features

Cross-cut is used only for creating firewood or interior elements. The work is carried out according to several principles:

Before carrying out work, the log is placed in a horizontal position on supports. Its height should be 0.5 m.
After that, it is necessary to completely clean the bark from the log.
At the next stage, it is necessary to make marks on the entire log, located at an equal distance from each other.
Then, according to the created marks, you can cut.

No specialized tools are required for cross-cutting.

Safety rules during work

To avoid injury, you must follow the basic recommendations:

Before using the gas powered tool, you must carefully read the instructions that come with the kit.
Since a chainsaw is a dangerous tool, work should not be carried out while intoxicated or sick.
Hold the saw with both hands. A secure grip will allow you to control the movement of the instrument and maintain its position in the event of unexpected jerks and in the event of kickback.
There should be no fuel mixture or oil on the hands during operation, as this reduces the reliability of the grip.
It is not permissible to use the saw if it is damaged, not completely assembled or not adjusted.
During work, there should be no children or animals on the site.
In the absence of special skills, you should not use the chainsaw on stairs or other unstable surfaces.
Do not cut with outstretched arms and above shoulder level.

By following the described rules, the risk of injury is significantly reduced.

Home >> >>

For carpenters, boards and beams are the most common blanks, of which crafts and wood products are subsequently produced. And the first thing the material undergoes is sawing into pieces of the required length. At the same time, you should know how to cut the board evenly, because incorrect performance of this operation can spoil the workpiece or significantly affect appearance, and not for the better.

At large enterprises, the problem of how to exactly cut a bar or board does not arise. Any serious production has high-precision equipment that performs this type of work. At home, you have to make do with what is at hand. At the same time, you still need to be able to use the tool or equipment correctly in order to saw off the board correctly, and the cut turned out to be flawless.

Note that many companies that sell boards and beams provide cutting services. And for this they use all the same specialized equipment, so the purchased material will be cut efficiently. But it is not always possible to use such a service, and it often happens that you only need to cut one workpiece.

You can cut a board at home with tools and equipment such as:

a circular saw;
hand saw;
angle grinder ("grinder").

Each of these options has its own specifics, which is important to consider before starting work, that is, you need to know how to cut a bar or board with this or that tool so that the cut quality is acceptable.

Circular saw - high productivity and ease of use

The circular saw is the best option to perform work. It has excellent performance and allows you to cut a considerable number of blanks in a relatively short time, and with high quality. In addition, such a saw allows you to cut the material longitudinally, but you need to know how to cut the board straight along.

One of critical criteria when choosing a circular, is the maximum cutting depth. There are devices on the market that cut materials with a thickness of 30 to 130 mm. That is, you can choose a machine for cutting only thin boards, and for sawing bars.

It is also worth paying attention to itself cutting tool... Discs with large quantity teeth will provide a neat, high-quality cut, while the cutting speed will be low.

Sawing along the grain.

But discs with a small number of teeth will provide high productivity, but the cut quality will also be worse.

Now about how to cut straight with a circular saw. One of the conditions for high-quality performance of work is reliable fixation of the workpiece. If the material is weakly fixed, then when cutting the board may "go" and the cut will be uneven.

If the circular saw is hand-held, then all work should be performed on a workbench equipped with stops and guides for workpieces. Such a device can be made independently, taking any table as a basis.

It is important to set the cutting depth correctly before starting to cut. In some hand saws there is an adjustable side guide with which you can perform longitudinal sawing material. If there is no such device, then use the same workbench.

More convenient in terms of work is the table circular, which is already equipped with everything you need - guides, clamps. Often, such equipment also allows you to cut the workpieces at an angle.

During the sawing process, it is important not to exceed the force on the tool, otherwise the quality of the cut will be low, the increased load on the saw will lead to a rapid dullness of the cutting blade.

Do not forget about safety precautions when using such equipment. Work should be carried out only after checking the saw's serviceability and the correct fastening of the workpiece. Also not worth neglecting protective equipment- masks, glasses.

Hacksaw - simplicity and safety

A hacksaw is a simple tool that is quite suitable for work. And although the cutting speed is low, and considerable physical effort is required, but for home conditions such a saw is the most acceptable option.

It is not difficult to cut correctly with a hacksaw on wood. The main condition for a high-quality cut of the material is to make the correct cut. To simplify the task, you can use a regular flat bar, which is used as a guide.

Often the question arises of how to smoothly saw off a board with a hacksaw at an angle. For this, a special carpentry device is used - a miter box. Moreover, it will help not only to make a cut at the right angle, but also allow any beginner to cut the board exactly.

You can also cut off a bar with a hacksaw. The only problem when working with such a blank is that you have to make a lot of effort.

The last option is to use an angle grinder with an installed wheel with teeth for work. But since the "grinder" is not intended for cutting wood, this method can be used only as a last resort: attempts to cut the board can result in serious consequences. It's better to use a hacksaw - it's time consuming, but safe.

Back to the list

All life will now flow in my VKontakte group, https: //vk.com/club37090442 here I only post a video, without discussions and comments.

Serge_msv: Well damn…
https://youtu.be/P-j2UNR2Sbo

Mila Solovyova: exciting movie !!!
Myocardial infarction !!))))
(for TO)
And so - super!
Thank you!

abs abs: Bitch!!

How to cut a board exactly

How smart and quick-witted our people are!

Sergey Burkov: How to dissolve a 3-meter board so that both the resulting halves are, for example, 10 mm in thickness

BANDIT #: you explain it to schoolchildren, with a countersunk head, etc.

Alex Lobo: Eco miracle.

COMPUTER: And if the board is 2 meters long? How will you put it on the priest?

Nikolay Sitkov: Ha, I didn't have enough intelligence before the hacksaw, although I faced such a problem more than once.

HOW ?: trees, take care of your fingers, bro. I wouldn't do that)))

Workshop on the balcony: Simple, cheap and cheerful :))) !!! Like

Mike VIZ: Hello, you have already had this circular in the frame several times. Is it AEG or another company? Maybe take a review, I choose a saw for myself, I would like to hear the advice of an experienced person, what is worth paying attention to.

Andrey Ivanov: Liked. Like.

Video on this topic

How to cut a board straight

The advantage of sawing logs with a chainsaw

The most accessible tool for work is a chainsaw. Such devices have several advantages over electrical ones:

the chainsaw can be used anywhere, regardless of the presence of an electrical network;
the tool is suitable for working in high humidity conditions;
professional chainsaws are much superior to electric ones in power;
you can use the chainsaw continuously for an hour.

Since household gasoline saws are not designed for heavy loads, it is worth using professional tools for sawing logs. When choosing, you should pay attention to devices with a capacity of more than 7 horsepower. Before work, the fixed frame is adjusted in accordance with the selected width of the boards. To create a frame, you can use the legs from a school desk or metal corners.

Types of working attachments

The choice of attachments for work depends on the volume and type of work being done. The following devices are used with a chainsaw:

drum debarker, which is necessary for removing bark from logs;
lightweight nozzle for sawing logs;
a standard nozzle used for making boards.

Rip saw attachment

Lightweight nozzle

Lighter

The nozzle for removing bark from logs is applied due to the wedge transmission. Attachment takes place with belts - special pulleys are used for this.

How to cut a log into planks with your own hands and not spoil the materials

It is worth noting that the performance of the nozzle can be changed, since the speed of rotation of the shaft depends on the size of the pulleys.

Features of sawing logs when using a chainsaw

It is quite simple to create additional equipment for sawing logs:

To create a support, a frame is used, which can be created from the legs of a school desk. The most suitable are pipes with a square section of 20 × 20 mm.
When constructing the frame, it is necessary to create 2 clamps, and fix the cross member at one end. This element must have holes for the tie bolts. A projection for the tire is created in the middle
In order to cut a log lengthwise, it is necessary to design a support frame, the width of which should be at least 8 cm in length.
For ease of use, a handle should be welded to the frame.
Before starting work, you must carefully check whether the frame is securely attached to the tire.

Using a homemade tool is easy enough. Before sawing, you need to install 2 trestles - they will be used as a support for the log. In addition, a metal rail or flat board is being prepared, which will serve as a guiding element.

Sawing technique along

The most difficult step in the process is making the first cut. For this you need:

install a guide ruler, which consists of two boards that are fastened together at an angle of 90 degrees;
after that, it is necessary to place the log to be sawn on the supports and fix it;
then it is important to check if the log is level;
at the next stage, it is necessary to fix the leading ruler on the supports using self-tapping screws;
after that you can start creating the first saw cut.

Cross cut features

Cross-cut is used only for creating firewood or interior elements. The work is carried out according to several principles:

Before carrying out work, the log is placed in a horizontal position on supports. Its height should be 0.5 m.
After that, it is necessary to completely clean the bark from the log.
At the next stage, it is necessary to make marks on the entire log, located at an equal distance from each other.
Then, according to the created marks, you can cut.

No specialized tools are required for cross-cutting.

Safety rules during work

To avoid injury, you must follow the basic recommendations:

Before using the gas powered tool, you must carefully read the instructions that come with the kit.
Since a chainsaw is a dangerous tool, work should not be carried out while intoxicated or sick.
Hold the saw with both hands. A secure grip will allow you to control the movement of the instrument and maintain its position in the event of unexpected jerks and in the event of kickback.
There should be no fuel mixture or oil on the hands during operation, as this reduces the reliability of the grip.
It is not permissible to use the saw if it is damaged, not completely assembled or not adjusted.
During work, there should be no children or animals on the site.
In the absence of special skills, you should not use the chainsaw on stairs or other unstable surfaces.
Do not cut with outstretched arms and above shoulder level.

By following the described rules, the risk of injury is significantly reduced.