DOORS FOR. interior doors You can install yourself. The materials necessary for this are inexpensive for this, but required tools There are even a novice homemade master.

DOWERS FOR CARTY DOORS: What do you look and for what you need

DOPERS (DOWNLOAD BOARDS) - it is wooden planks or MDF panels that close door slopes. Such slopes are formed if the wall thickness is greater than the width door box. As a result, the box does not overlap the entire end of the wall and can be seen naked concrete or broken bricks. Sometimes this section is plastered, covered with wallpaper, closed with plastic, but it's easier, faster and aesthetically to establish good.

Design of the door block using good

In contrast to conventional slopes, the good boards continue the missing width of the box itself, forming a single design with it. In order not to make a mistake with the tone, Dobors buy at the same time with door blast and navigate.

Advantages of use

• Right mounted volu products look presentable and depending on the total style solution They bring the element of wealth and luxury to the interior or restraint and solidity.
• Painty gooders are simply and quickly that saves time, strength and means.
• During finishing work door block It does not come into contact with wet solutions, which prevents it from turning and damage. Increases the service life of the door.

Finished design looks beautiful and modern

Dobors can make it easily or buy ready. The store will offer a good plank of standard sizes:

• length - 2.1 m;
• width - 7-25 cm;
• thickness - 6-30 mm.

To calculate the width of the task, the width of the slope add a groove depth in the box, or from the thickness of the walls take the width of the box taking into account the groove.

With a particularly thick walls, the width of the dough can reach 40 cm and more, but such planks are made to order. Thickness of a good plank should not exceed the width of the groove in the door frame.

Based constructive features, Dobly planks divide on:

• ordinary;
• normal with adamors;
• telescopic.

The easiest good is a straight strip of fibreboard (MDF) or laminate without a facing edge. Many masters believe that sticking the facing edge to the ends is superfluous by spending time and finance. After all, one end adjacent to the door frame tightly, and the second will be covered with a platband. But in this case, the installation should be done with a special care, because the deviation even for a couple of millimeters will give a novice master: the gray raw edge will rush into the eyes.

The simplest fair is the usual bar

If the end of the problem is pre-close the edge ribbon, selected tone into the tone, small flaws will be invisible. The edge itself is a penny, and you can stick it in a few minutes using conventional Iron. This method is preferable also because the edges of the ends prevents the mild-plane swelling under the influence of moisture. This is especially important for door blocks in kitchens and bathrooms.

A more advanced voluntary bar is distinguished by the presence of the edge on the ends

The most complicated design of the telescopic is good. Its feature is the presence of special grooves that allow you to install without the use of self-use and nails. Moreover, it is practically impossible to miss: the good is perfectly docked with the box and platbands. The width of the dough is regulated by the groove depth. To make a telescopic good independently, you will need certain skills and a special tool. It's easier to buy ready-made planks.

Telescopic door Dobor. Has special notes

Required tools and materials

When installing a problem, a minimum set of tools is used:

• level;
• roulette;
• pencil;
• saw or electrolybiz;
• plane;
• a hammer;
• a sharp knife.

Necessary materials:

• mounting foam;
• fasteners (selflessness, nails or "liquid nails");
• dobly planks.

Typically, good-faces are bought with the door cloth, but if the doors are not going to change, but they only plan to close the slopes, for the manufacture of problems use:

• wooden planks;
• mDF slices;
• long DSP trimming;
• plastic.

If applied natural treeTo extend the service life, it is pre-treated with antiseptic impregnations.

Homemade doblors from ordinary MDF will differ from the factory, since in industrial samples the interior between two thin wood-fibrous plates is filled with cellular material.

Wood-chip plates lose the tree and MDF in appearance and durability, but dope indoors from chipboard can be applied.

Plastic as a material for the manufacture of goodholds is rarely used. And if it is still used, it is selected especially durable, reinforced by metal PVC panels.

Dobors can be made of natural wood, Chipboard, MDF panels or plastic

Installation of volunteers

Installation in groove

If you plan to use good, the door frame is better to buy with a special groove. The presence of a groove not only accelerates the installation process, but also allows several millimeters to put forward / plug in the challenge in the box, which increases the accuracy of the installation.

1. It is assumed that by the time of the installation of the goodness, the door frame is already fixed in the doorway. Therefore, first measure the distance from the door frame to the edge of the wall. All slopes are measured separately and each minimum in four points. As a rule, these indicators differ: Even if the box is installed strictly vertically, the wall itself can be uneven.

   Measurements are convenient to produce a construction kit

2. A width of the slope add a groove depth in the door frame. The value obtained determines the width of the task.
3. Electrolovka or saw cut the dobors in length and width to of the desired size.

   Dobly planks are bought with a stock in width, and an accurate fit is made in the installation process.

4. Dogs are installed in the dump box.

   Design of the door block using ordinary doors

5. If telescopic doters are used, the door frame and platbands should also be telescopic. The entire block is collected as a constructor, inserting the protrusions of some elements in the deepening of others. For strength, good planks and platbands are planted for glue or "liquid nails". The design assembled in this way looks like one.

   When installing telescopic problems, the "spike in the groove" method applies

6. The upper horizontal kind lies on the side, forming the letter P.

   Upper Dobor lies on the side at right angles

7. To ensure the fixability of the goodness, they are temporarily attached to the walls and box with a painting sticky ribbon.
8. Eliminate voids formed between a good bar and a wall, filling the gaps mounting foam. As a rule, the struts are installed between gooders. If there is no strut, the clearance is rented in several stages so that the foam is not too saturated layer door Piece.

   The gap between the wall and the good foam fill

9. Wait a few hours and after hardening the foam, its excess is cut off with a knife.

   The use of foam during installation allows you to do without nails and screws

Installation without groove

If there is no special groove in the door frame, the dobors fasten the oppressive. This installation requires a very accurate (up to a millimeter) measurements, careful fit of the good slats and special accuracy during installation.

1. Measure the width of the slopes as the method as when installing the problems in the groove.
2. Crop the challenges to the desired size. If extra millimeters remain after sawing, they are cut off by the plane.
3. On the resulting sections are glued edid ribbon.. For this, the edge stroke the hot iron, as a result of which the glue on the reverse side is melted and the ribbon is firmly attached to the bar.

   The edge is glued with an iron

4. Thin nails up to half are clogged into the ends of the voltages with a step of 20-25 cm. If you additionally use glue, three nails on vertical good and one (in the middle) on the horizontal.
5. Hats nails bite off at an angle so that the end was sharp.

   Nails are clogged into the end of the good and bite the hats

6. Install the best in place - first the side planks, then upper. The vertical good is tightly pressed downstairs, bother and finish with a hammer, so that the nail entered the door frame. Then nourish the middle, then the top. They follow that there are no cracks between the good and the box.
7. The upper horizontal bar is put on the vertical, check the straight angle and naple.

   After installing the problems, nails are not visible

8. The gaps between the wall and the goodness are fought as well as when installing the problems in the groove.

Installation of trimming

After the dobors are installed and the mounting foam dried, the platbands are fixed.

1. Measure the height of the side planks. To do this, the top of the door width is added to the height of the doorway.

   The length of the vertical platband is calculated, taking into account the width of the horizontal

2. The top of the right platband is roasted at an angle of 45 degrees in such a way that the edge of the planks will be shorter to be the edge.

   Cut the platband at an angle exactly 45 degrees will help the stub

3. Also at an angle of 45 degrees, but in the mirror image, the top of the left platband is pushed.
4. Scram extra length from the platbands.
5. Vertical platbands are installed in place and everyone is enhancing two nails - downstairs and in the middle.
6. Apply the upper platband and make marking.

   It is preferably to bite off the nails. So they will be almost invisible

   If screws are used instead of nails, then first drill a hole in which the hat is drowned. Then they screw them, and the hats are closed with special plastic plugs.

   Independently to establish goodness for interior doors is easy, although the process will not call fast. But if everything is done correctly, the new door block will become the main decoration of the room.

What is good? Why are they needed when installing interroom doors? What are the samples of the edge and the fitting method? How are the good? These and other questions will describe in detail in this material.

Usually we are talking to customers "If you have a wall thickness more than 7 cm, you will need good." To determine how to determine whether it is necessary for your doorway good, you should correctly measure the doorways.

How to determine the amount of good?

Almost all doors producers are sold standard width - 100, 150 and 200 mm, and the door frame is almost always 70 mm width. All this is to the fact that before installing it, they must be cut along to ask them the desired width.

For example, if you have a wall thickness of 90 mm, it turns out that you will need another 25 mm wide to the box. (Approximately 5 mm is needed to insert a dog in the grooves), but such a good width is not sold, so we buy a good 100 mm wide and sprinkle along each edge of the good strip 25 mm.

As a result, we will remain another strip of the dough (middle) with a width of 45 mm (5 mm left for cuts), which, theoretically, can also be used on the top of the box, but in practice it is not done, especially if goodholds have crude edges t. e. The end of the good has the same coating as the facial part of the good.

DOWERS, no ferments have, mostly, only veneered doors. Veneer (thin tree cut) is not an elastic fragile material and beatened it at right angles and cannot be broken. Therefore, almost all vehesions do not have the edge. Doborities with artificial coatings (laminate, PVC, ECOCHPON, laminatin,) have chosen ends. In addition, like a door frame or platbands, dobors are also simple and telescopy.

Top Top Top

We return to our example with a sip of kind with a wall thickness of 90 mm. For this case, 1.5 of the stalk of the goodness will be required. From one stick (board) of good, we make two kind, sawing it into parts, and from 0.5 of the good, they also scold a piece of the desired width and put on the top of the box.

As a result, it turns out that if we have a wall thickness from 70 to 90 mm, then we will need a complete set of kinds (2.5 sticks), but there will be 1.5 sticks with a width of 100 mm. If the wall thickness is from 90 to 165 mm, then a complete set of problems is needed - 2.5 sticks width 100 mm.

Table 1: Completeness of nonsense for door openings for interroom doors. The right amount Dobor for each case of the wall thickness of the doorway.

Standard Width Options

Telescopic Dobra and their features

As already mentioned above, dobors are with the edge and without edge. There is another third type of edge: the end of the good has a slot. These are telescopic dobilities that are designed to install telescopic platbands.

What are the features of telescopic sobers? For example, if the wall thickness in the doorway is 800 mm, then it is possible to save: buy doors with telescopic components, and good things can not be bought. The missing 10 mm we close a telescopic platband due to the fact that it can be pulled out from the groove of the box for 5 mm on each side of the door frame.

Although the telescopic handle costs almost one and a half times more expensive than simple, but in our case we not only exclude the cost of the goodness, but also the cost of their installation. In addition, if the telescopic good has to be cut in half, it will be harder to mount it, because We'll have to prepare a box for a good thing, which will also entail additional costs.

Some manufacturers make dobors one-sided, i.e. Cutout for telescopic platband only on the one hand. When drinking a kind under the desired width, it certainly facilitates the work on fastening the goodness to the box, but minus is that such goodholds will always have to buy in complete set By quantity, because Do not cut them into two parts.

If the walls are wide?

As a rule, the doorway in brick houses or in carrier wall It may be a thickness of more than 300 mm. In this case, it is better to easily and cheaper to reflect the doorway under the wall (caught with wallpaper or paint) and do not betor. The minus is that unprotected angles of this opening risk quickly damaged. Therefore, dobors are installed in all the opening and on both sides are placed by platbands. There are two ways to solve this task:

1. Close the end of the door opening with solid goodness. Many doors manufacturers make wall panels or good shields. In fact, these are the same diet width about meters. In addition, the order can be ordered good widths, but only multiple 100 mm. In the extreme case, you can buy wall panels of another manufacturer, pickup in color.

2. Close the end of the doorway docked by docking. If, for example, the thickness of the wall is 30 cm, then you can take two sets of voltage widths 10 and 15 cm and docile them, sign one of the sets in width. Especially well to keep telescopic dobors using a stapper.

Installing goodness

Dobors are installed when collecting boxes. At the beginning we collect the box, and then painted in the desired width of DOPERS Breeping to the box with the help of special mounting plates with short screws. Thus, dobors with the door frame become one whole. All this design is mounted in the doorway.

It is not recommended to put the door frame separately, and then wide dotor is not recommended separately because it will be reliably consolidated to the box will be problematic. If it is not fixed or completely glued, then over time, the goodness from the box can move away by forming a gap. Separately, you can set dogs width no more than 50 mm.

Now I will establish a good on this door. Dobor will be telescopic. For those who do not know, this is what he is in context.

Here is such a groove. There is a groove in a challenge. And on the cashbox there is such a spike. A cashier has such a profile.

What is it done for what. That's when we put a good, then the cash is inserted into it. And we can adjust the distance within this pass. Approximately one and a half centimeters.

Now if we have, for example, this distance is not 8 centimeters, that's how here. And there from 5 to 15 millimeters, we can make a cash immediately without a good. This box it is certainly not telescopic. This door was installed for a long time. it simple box. In general, there are passes in telescopic boxes. Immediately, in order for the ticket to the way could be mounted.

What I start to install a good. First scold in height. First, the next bottom, then here I make a tag with a stationery knife and screaming into 1 millimeter in short.

Then, I take the carbon and measuring this is the distance from the box to the edge. And add a groove depth. In this case, it is 1 centimeter. And I make marking on the reverse side. Here is the line.

Well, here it is necessary to take into account that it is necessary to cut off from the other side where it will be inserted into the box. Because this edge cannot be spoiled. Well, here I expect a Dobly Planck somewhere for a couple of millimeters less than the plane of the wall itself. Because it does not matter here. I can have these 2-3, even 5 millimeters to adjust this thorns of cash. If the usual Dobly Planks, then I, on the contrary, make a 1-millimeter more than a width of a task. For what? To prevent anyway in any case. And you need to measure. The walls are not always in the level, so I measuring at several points. Well, about 4. at the top, somewhere here and below.

If the wall is approximately smooth, you can at 3 points. And caught up, thus, the left and right-handed bar. Then on top of them mount the upper, right on them. I scream all this thing is a jigsaw. Can circular saw Some carket or mini-circular. Upper bar, I place like this.

Here I put it so that this edge of it is before the groove. Here I also place, right in the groove. Knife once and that's it. Then I turn it over and insert it like this. And here we already make tags as it were in width. Because there is a different left edge and right. So we make tags. Here and here. Like this.

And then Cherch and cut off.

Installation of good

So, now that our setup is prepared all the planks, we will install them in place.

Here it is here that the plane coincided. I check her fingers.

So, there is a straight angle and to the groove. That's what we do.

Like this. Why do you need to do here? In order for when the cash is inserted, there's nothing nevertheless, neither hurt. And this corner will be tightened, that's how it will be. Here it is.

It should be. This plane also coincides. Here she is. Here too. All coincides.

In the event that here in this corner, for example, a gap is formed. Well, there is no foam, for example, to rest. I will drive here and screw the screws. They, as it were, are emphasis, and they support the whole corner. That's all. Now we will mount them. To do this, first I smell this thing, so that the foam is better to go. It expands more evenly.

Because foam expands under the action of moisture. So, we take foam. And here are such cakes I pass the whole perimeter.

Now I take a big scotch wide with me. And fix good. I follow that there was a straight angle.

And so around the perimeter. So, all this fixed. After about one hour, you can already remove everything and put ones. I also do this procedure and from this side. From the edge and on top. Everything, good things will be ready. This attachment is quite enough. There is no load here. No mechanical fasteners are required here. That's all this good is ready. You can say now it will freeze all. Repaled, fixed.

Why do I do these points, not a solid. Two reasons. Firstly, foam savings. Secondly, the guarantee that good-doors will not be squeezed by Arc. Because there is a foam where it will expand in free space. That's all. Good made. It is done not for a long time for 10-15 minutes. Now I will make a good on another door. During this time, the foam will finish and it will be possible to start doing a ticket.

Installing tickets

Here is our good frozen. I cut foam, removed the scotch. Now I will put a ticket. But I will put it here under the corner of 45 degrees.

In general, telescopic tickets put, as a rule, here it is suited at right angles here. And on top of cash comes here, like this.

But, because on this door cash is already installed like this. So, on this side, you also need to do so. How to post. That's how I take and here I put a half-meter with a knife. Like this. Everything, cut off here and here.

I put the top first. Then I also substitute the vertical here so the brass. That's how I put and make a tag. That's how it, for example, is worth it. And I have it.

So once and put a label. Here it is, it can be seen slightly. And I cut everything. First, of course, it is necessary to slow down the bottom, and then I embraced liquid nails here on this edge. Here. Here on this road edge, like this.

Here, here and along the entire length. And the prince of it. Because if we glue the whole groove. Fill this glue everywhere, and it will be almost impossible to remove it. She and so there is tight and it must be fixed a little bit. You can apply glue here. On the wall straight, several points. This will be enough.

All and insert. You can between them a little.

All and mounted.

So, that's what we got in the end. Here is such a corner.

Here you can pick up a pencil, so that this seam is not visible. It will not be strong in gas to rush. And here is everything here. Everything is clear and beautiful. I'll show it now as a markup to do. Here put, the knife is like that.

Everything. There is a label. Now this takes the label, so. And at right angles, hold the knife and carry it. Everything, now you need to cut off diagonally. Everything goes to the ending. True here because there is a groove, it becomes crooked. I simply put the woods in the thickness of this distance.

Here I put here and it becomes smooth. And I scream.

Well, what we got in the end. Such a good. Black, poorly visible, well, nothing. Now I'll show you.

Everything is tight, everything is smooth, no cracks. This node. All, the door is absolutely ready.

All rights to video belong: Roman Zaitsev

You may face face to face with a problem, the essence of which is that standard openings are suitable only for standard doors. There is still a situation where standard box Does not coincide with the walls in. You can close the gap by mounting foam, and then long and tediously cover the opening of the opening. But it is better to do everything much easier. Take advantage of good (expanders), increasing the dimensions of the door frame.

DOWERS are panels that have a thickness from 5 to 400 mm, and you can do good large sizes. They are vertical and horizontal. Dobori degrees appearance Door opening, giving the monolith of the entire structure, and will also greatly make it easier for the repair process. The color needs to be chosen the same as your door with the door frame.

Install good things. If you have special grooves in the door frame, you can safely take a good one with a 10 mm wide strip. But in the case of frequent doors, any in the width of good planks will be suitable. Dobors are usually attached on one side of the door. Although there are situations where the box must "increase" from two sides.

Installation can be carried out before installing the door. To do this, it is enough to fasten the best to the back of the door frame. And if dotors are mounted on already installed door, you need to drill a thoroughly and secure myself a good to the door frame with a self-tapping screw through the hole. If you do it does not allow the width of the opening, try to navigate the rake with an indent from the edge of the door box. True, in this case there may be a gap to appear. But it is not difficult to smell a sealant.

Horizontal dobors are installed after vertical, on top of them. After that you can be engaged in platbands. Installing good - it's not very complex, but painstaking. So it takes a few hours for installing the voltors only on one door.

If there is a desire, you can make kinds yourself. Just cut for this panel of the desired sizes, fuse them exactly in the color of the door. If the walls you do not have very smooth, make a snap-in with a small slope. Then you and the walls visually align.