Probably, each in the house can be found wooden furniture. Most often such furniture are wooden chairs. They are strong enough, eco-friendly, and also have aesthetic appearance.

However, in contrast to plastic, these products consist of a variety small detailsinterconnected by glue.

Upon expiration of a long time, you can see the squeak of the chair and the opening of certain joints. If you have been found that the chair began to try and crack - this is a direct evidence that the leg began to separate from the strapping to which it is attached by spikes or brazers.

As soon as it was noticed, it is necessary to think about the better to glue wooden chair. This does not mean that the chair is completely broken and it's time for a landfill.

Without spending special means and putting some efforts, you can repair the furniture and give it the former strength simply using special glue.

First of all, it is necessary to pay attention to the characteristics.

Use:

1. Kleiberit Pur.
2. Moment of the joiner.
3. Trebond.

Signs good glue are:

• Light resistance;
• Adhesive strength;
• Water resistance;
• The absence of traces on the surface.

An ideal option for these purposes will be glue based on PVA. You can also use epoxy or two-component glue. But it is important to remember what to buy glue - this does not mean that the case is done.

It is important to properly prepare for the gluing procedure: the quality of the work done will be directly dependent.

Video on the topic

Most of the parts of the wooden chair, including legs, are interconnected using glue.

Over time, such seams tend to weaken and strip, so very often chairs are broken. But do not despair about this.

To solve the question how to glue the leg of the chair, just get enough required tools, namely:

• Hammer having a tip of rubber;
• Emery paper;
• Durable glue intended for furniture;
• Press;
• Acute knife or chisel.

When these fixtures are prepared, you can proceed to the main process of gluing the legs of the chair. Furniture having simple design, Repair does not constitute special problems, it is only important to comply with the phasetance in the work:

1. To begin with, it is necessary to withdraw a tenting leg from the nest, and its upper part, which is inserted into the groove (ass) should be cleared of dried glue. In the event that the previously applied adhesive is difficult to remove, it is possible to displete it by means of water vapor.
2. If there is a thin layer of glue on the chair, it can be removed by emery paper, If it is thicker - it is necessary first to remove the glue layer with the help of a chisel or an acute knife, and then process the sandpaper itself.
3. After that, you need to apply a layer of glue on the pin, and also insert it into the seating socket. In the event that Cords leg is badly crashed into the nest, it is recommended to knock on top of it with a hammer, equipped with a rubber nozzle. Also allowed to make some press.
4. Visible glue residues should be removed using a piece of fabric.
5. After the day when the glue is absolutely dry, you can use the chair.

Only properly gluing chair leg You can count on its reliability and strength in the future. Without compliance uncomplicated rules, some tricks, desire and without resorting to the help of certain tools, it is simply impossible to achieve a positive result.

Glue is best tool For repair wooden furniture. Adhering to the instructions prescribed on the packaging and considering all the requirements of the gluing, each has the opportunity to achieve their own hands and make the place of gluing more reliable and stronger than the wood itself.


Mainly for the repair of furniture and in particular wooden chairs, the following types of glue are used:

• PVA. This glue stands to temperature changes, easy to use and completely does not leave traces. It must be applied to a non-fascinated surface and come in place of the connection. Absolute drying should be waited after 24 hours;
• Casein glue. It often changes the color of wood, is distinguished by its strength, but in places of adhesive is able to leave a noticeable mark. The glue is a light powder that is divorced in water to a state of thick sour cream, after which it is recommended to mix with water about 40 minutes. Dried glue has greater resistance to temperature differences;
• Synthetic glue. This species The glue is used even on a crude surface, characterized by good indicators of frost resistance, moisture resistance and strength;
• Carpentry glue. It differs from other types of glue with incredible strength, resistance to temperature differences. Almost always its quality depends on the proper preparation process, which provides for compliance with the proportions when mixing it with cold water.

And although modern market It is capable of offering buyers a rich assortment of firms manufacturing glue, you must first familiarize yourself with the characteristics of a particular product to make a subsequent right purchase.

It is difficult to stop your selection of glue for a tree, given the many brands that have recently appeared on the market. Here and polyvinyl acetate (PVA, which is yellow and white) and polyurethane and epoxy and even traditional bone or megro glue.

All of them are designed to glue a tree with a tree, as well as cloth, paper and leather.

To pick up exactly the best way, Learn the tables and descriptions below that will help you take the right decision.

If your product is not exposed to moisture, use the top table, and if it faces dampness, use the bottom table, even if the project is designed for the premises. Then check the opening time of glue and other characteristics.

Short advice! It is likely that the bottle with moisture-proof or waterproof PVA glue will be enough for most of your projects designed for home and street.

Double carpentry for internal work
Open exposure time	less than 5 minutes		10-15 minutes		20-25 minutes	60 minutes
Irreversible slace	Cyanoacrylate ("Second Glue), thixotropic PVA (no - Drip.), polyurethane glue melt, 5-minute epoxy glue		Standard PVA, moisture resistant PVA, Dark moisture resistant PVA, Polyurethane glue		PVA with slow-grapping, moisture-resistant PVA with slow down grasp, waterproof PVA	Standard epoxy glue
Reversible gluing *	Traditional joiner (bone or middle) glue				Modified joinery glue
"Steam processing allows you to disassemble the connection if necessary.
Moisture-resistant and waterproof types of glue for the tree
Open exposure time	less than 5 minutes	10-15 minutes		20-25 minutes		60 minutes
Episodic moisturizing	Polyurethane glue - melt, 5-minute epoxy glue	Moistureproof PVA, Dark Moisture Resistant PVA, Polyurethane Glue		Moisture-resistant PVA with slow down grasp, waterproof PVA		Standard epoxy glue
Frequent moisturizing	Polyurethane adhesive melt, 5-minute epoxy glue	Polyurethane glue		Waterproof PVA		Standard epoxy glue
Immersion in water						Standard epoxy glue

bryansk 11-01-2013 11:37

Wood - Grab.
Here, in fact, the question is what glue to use?

unname22. 11-01-2013 12:55

Epoxy resin

bryansk 11-01-2013 13:15

The first thing I thought. Maybe there are some others, it is the rigid adhesives that are better?

unname22. 11-01-2013 13:24

Epoxy resin))

KM 11-01-2013 13:36

Cue? There will be no effort and epoxy will not go. You can try to clear the connection from the remnants of the glue to the pure tree and try to use glue for wood. For example, based on PVA. Glue under pressure.

Carbofos. 11-01-2013 13:42

Normal epoxy resin, eg usual ED-20 + PEP
we also need to take care of the surfaces on the surface.
it is important to thoroughly clean the surface before gluing

Carbofos. 11-01-2013 13:43

There will be no effort and epoxy will not go.

Will be. Gone

KM 11-01-2013 13:49

Carbofos. 11-01-2013 14:06

qUOTE: Originally posted by km:

If it is cut outside with a tape impregnated with glue.

Not. Epoxy resin (not Pokilipol and ED-20 of course) impresses the tree and creates the structure of a stronger tree.
That is, the seam and the place around it will be the stronger the rest of the tree.
It will not work if Kiy cooked in oil, but I doubt it

Serjant. 11-01-2013 14:19

it will not be impregnated with cyanocrylate ?? (Super glue)

Carbofos. 11-01-2013 14:44

in the photo, it is not very clear that there .. will not come up with cyanocrylate ?? (Super glue)

Soaking wood, it is quickly polymerized. Most likely it will happen earlier than it will be applied to the entire seam.

Serjant. 11-01-2013 14:47

blucked, diluted with acetone cyanocrylate, I was impregnated, dried, polished.
I was impregnated again. polished.

Nikofar. 11-01-2013 14:59

So, Andryushka, broke his brand glue ...
So. The gluing technology of set kiyov for the Russian billiards involves the use of a mixture of fish and bone glue. To repair a cue and must be applied. But it is better to go to the workshop where Kii do. Otherwise, you can simply spoil the dear pribud under the bucks worth.

bryansk 11-01-2013 15:04

Uncle Kolya, Pribluda worth 2 pieces of bucks. Contact the workshop - I turned. Stick will take place in Moscow time, they will do there. They want 4 pieces rubles. I, firstly, not clear the pricing is, secondly - well, I figured it out - I'll try to glue myself, and if it breaks, then I will give it.
Fish and bone glue - I will definitely not find. Therefore, I will try with epoxy.

bryansk 11-01-2013 15:05

qUOTE: Originally Posted by Serjant:
the photo is not very clear what's there ..
it will not be impregnated with cyanocrylate ?? (Super glue)

In the photo - the place when it was still whole. There is this stick, called the shaft - made of two pieces connected by the "crown". Well, that is, there is an EO as if two schematic by depicting the crown by the horns to each other turn - this is where the connection is there.

Carbofos. 11-01-2013 15:13

Therefore, I will try with epoxy.

well, essno resin and hardener strictly on the scales and all that

unname22. 11-01-2013 15:21

Bone glue is a normal gelatin.

bryansk 11-01-2013 15:21

qUOTE: Originally posted by carboophos:

First practice on the thread easier.
I can see two options how to ruin cue
1 Pots from the resin that will be very difficult to remove
2 Perhaps the drive around the seam is more damaged than the rest of the tree
well, essno resin and hardener strictly on the scales and all that

Drinks from resin - erased when they performed. Then, when the glue grabbed this place inspired at first zero, then the 2000th (?) Skin. Then this place is processed by hot wax and polished. Here I have some experience there. Kaimka, even if it appears - on the drum. Kiya is still being taken by hands and on a general background, this kaimka will not be visible. And even if it is, which is unlikely, it is not entirely scary.

DVP 11-01-2013 15:25

Once the seam on the PVA was obtained strong material. Try to find normal

mukdiver. 11-01-2013 15:38

Old glue should be removed

Nikofar. 11-01-2013 15:43

Alexey Eremin's workshop: http://www.youtube.com/watch?v\u003dgg8e2j30p4w.

Shl. Andrei, how did you manage to break in two pieces of bucks?

I have much cheaper than cue, typing from tees and rosewood. And then I do not break it. And you quiet from the Grab managed to break ...

Nikofar. 11-01-2013 15:47

Andrei, I think we, the masters of the Russian billiard (), it is not particularly interesting, but the other link may be useful: http://alekseyeremin.ru/blog/sacral/sekrety-master-1

bryansk 11-01-2013 16:02

how-like .... Kher knows, I do not remember. Highly "cheerful" was. But there it was visited by a constructive defect. Someone attended initially, it seems to be blocked. Or maybe I tried to break it ... This moment I remember. I remember the current of it stands and looking at two halves in my hands.
Come is not from a ram - only the shaft from the Grab. Turnyak there is a whole package of valuable breeds.

Mower_man. 11-01-2013 16:07

If the wood is not impregnated by the tape of the old glue, I think that the Tyobond D2-D4 series will fully go, the seam should be conditionally flexible, since the shock loads in order from the balls, as I understand it, is very stupid, and the epoxy is harsh.

Guccio. 11-01-2013 16:38

Kiy has some qualities for damage. I think the epoxide of these qualities does not and sooner or later break down "by seam". Two years ago, the best, in the gluing two trees showed itself a solar plow in a yellow tube.

Camenelenbogen 11-01-2013 17:25

Father Mikhail 11-01-2013 17:28

qUOTE: Originally Posted by Bryansk:
There is, let's say, a wooden cylinder, a diameter of about 18 mm, consisting of two parts, which was attached to each other with the "Crown", on the glue. Onemost moment, it was taken on the break, and the connection was broken. Himself washed - not suffered. It is necessary to glue something, and it is desirable so that there was no breakdown in the future.
Wood - Grab.
Here, in fact, the question is what glue to use?

The photo highlighted the place of the collapsed gluing.

Andrei, and not easier to turn to the masters of manufacture and Kiev? They have something for sure and the recipe of glue and the adhesive itself is available. AND more easierAnd most importantly - reliable. You yourself understand that at least 1 mm stick in the place of docking is incorrect, and hello, as a rifle with a curved barrel will not be visible, it is possible to shoot. But does not fall.
Maybe better not to risk? A stick then you are not easy, not quichetics serial, and a good handmade workshop work

mukdiver. 11-01-2013 17:31

qUOTE: Andrei, and not easier to turn to the masters of manufacture and Kiev?

Toad...

Guccio. 11-01-2013 18:18

And if such a conversation of the Billiard lovers went, I will ask if Bryansk is not against.

Whether the master is tested in Moscow, who can stick to repairs to rewind / give, namely: gave cue, made a master from Nizhny Novgorod., Master is good, but scholluril, apparently. Did not look when buying, bending smooth. I checked the year, but never stretched out. Billiard room closed, and the contacts of the wizard were lost. Of course, it is possible to write, asking, but troublesome it, 400 km still.

Nikofar. 11-01-2013 20:17

I want to know if it is possible to fix it?

With respect, Nicholai.

Nikofar. 11-01-2013 20:32

By the way, Andryukh, which Topikstarter, you will travel in Moscow, capture a broken cue and zinking to me. My phone you have. I make you your cue.
And I will give you my time for you, so that you can play with good kiy. True, he has "Zadga", thin and "bottle" in the saffa. Do you have a "smooth cone"? How do you play them, still surprised ...

Guccio. 11-01-2013 20:36

Dmitry, judging by profile, are you in Moscow?
I am a little restoration in any different way, including the "editing" of Billiards Kiev. If you only need to fix the bend of the shaft, I can help. In edit, there is nothing difficult, I even have adapts for this. The procedure itself takes from several days to a pair of weeks. If there is a desire, skip the PM contact phone. This work I am ready to perform for free or purely for a symbolic remuneration on your part.
With respect, Nicholai.

Thank you very much for responded! Come hangs in the office, tomorrow I will pick up, I will examine attentively, so that you do not disturb you once again (I looked at it on the subject of bend 3 months ago, before that he saved the year and "not stretched"). If everything is still left, then you will immediately cut your phone to PM and agree on the meeting.

natalia_VW. 11-01-2013 22:53

yes .. I myself would not risk glue for 2 brush, I would give a workshop without looking or the nicofar chtoli. The most chased glued on the eye decorative decoration brought from Israel and they initially offered to double-sided tape, fell off and split, glued the superclosure of the seams not visible, but the cow on the door itself was glued only to liquid nails .. On the other cleaned, she slipped three times.

unname22. 11-01-2013 23:19

natalia_VW.
Eyes afraid ...
Masters are the same people

Chaintych 11-01-2013 23:21

On the tree is very good "Kleiberit", I have a friend on it musical instruments Build. Only parts should be very pressing - the composition foams

bryansk 12-01-2013 11:30

qUOTE: Originally posted by nikofar:

And I will give my time for a while,

Nikolai Fedorovich, thanks for the concern, I now have three sticks of my

bryansk 12-01-2013 11:32

qUOTE: Originally posted by Camenelenbogen:
Have a custom stick and not know who to repaired it?

And how did it manage to be a partner under the blow performed, and did not take a robo?

Who knows. Just for the glue of a stick of 4 kosary - somehow it is not clear. There's nothing complicated, the whole operation is 5 minutes.

bryansk 12-01-2013 11:33

qUOTE: Originally Posted by Father Mikhail:

Andrei, and not easier to turn to the masters of manufacture and Kiev?

There are no them in Bryansk, it is necessary to move in Moscow time.

bryansk 12-01-2013 11:36

And in general, yesterday evening came to the billiard room - it is worth my cue, a whole. I'm a ditch * Eating Malts, I ask - how? Man laughs - you a gift for new Year. Soiled, glued down the padles so sorry for a false alarm did not know that no longer need to glue anything.

bryansk 12-01-2013 11:43

qUOTE: Originally posted by Guccio:
And if such a conversation of the Billiard lovers went, I will ask if Bryansk is not against.

I want to know if it is possible to fix it?

Nikofar. 12-01-2013 12:31

qUOTE: Originally Posted by Bryansk:

Can. We warm over gas and wound up in needide. Current not overdo it.

So, I took and all the "gesheft" broke me ...
In general, this operation is made by clamping cue into a special device, such as weama, straighten the lateral bend by the adjusting screw and warm the place of bending with an industrial hairdryer. Then leave in such an intertwined form for several days or weeks so that the tree accepted fit form. Nothing complicated and allows you to very accurately restore the geometry of the victim of Kiya. I straightened my cue for the pool when he had a slightly curled, from the fact that I longer hold it all winter in the trunk.

Chaintych 12-01-2013 12:37

And in general, difficulties on the billiards, in my opinion, begin when it is necessary that the balls in the Luba fall. The rest is ordinary

Nikofar. 12-01-2013 12:43

qUOTE: Originally Posted by Chaintych:

complexities on billiards, in my opinion, begin when it is necessary that the balls in the Luba fell.

And there is nothing complicated in this.
Once at the billiards tournament, one of the observers for the game made a remark to Schwarzenevere:
- Allow, Arnold, but in the place where you are, no Luba!
- scha will.

Chaintych 12-01-2013 12:54

qUOTE: Scha will

Who is playing ...

Guccio. 12-01-2013 17:07

qUOTE: Originally Posted by Bryansk:

Can. We warm over gas and wound up in the right direction. Current not overdo it.
But in general - not to bathe. If the bend is not a propeller, but purely, when you show on the table, it walks a little - to score sex hue to this matter. Does not affect the game.

It's buulshit. My Russian Kiya did a snooker. At home. With the help of two drills and some mother. Stopped, then polished. When I learned about it - I was flooded. But - the stick smooth turned out, excellent.

And you say a stick to glue the wizard to give ....

No propeller, but walking, at least it was noticeable. Tomorrow I will pick up - I'll see. I was offered construction phenomenon Heat and fix. But I somehow fear to spoil such a delicate thing

Nikofar. 12-01-2013 17:20

qUOTE: Originally posted by Guccio:

But I somehow fear to spoil such a delicate thing

For me, this is a familiar job and I guarantee that I do not ruin the shaft of your cue.

alex1. 13-01-2013 16:54

At one time I broke the butt from IL-27 / I finished the hare. Sklexed epoxy. The note only does not fly with the components, I had to plunge butt in the oven for the polymerization.

Guccio. 14-01-2013 12:33

qUOTE: Originally posted by nikofar:

My offer on repair in force.
For me, this is a familiar job and I guarantee that I do not ruin the shaft of your cue.

Nikolai, I sent you a letter to PM, please check.

Nikofar. 20-01-2013 02:08

Dmitry, put over your kihe. Current, professional, in my opinion of the amateur.
Kazan and Belarusian masters are so doing.
The curvature on the safta is about 0.15 hundredthmm, the tour is direct.
In addition, in my opinion, there is a small axial mass imbalance on the saffa, because the curvature is simply not defined on the eye, I found it only with a typal probe-thickness plate at the test plate.
Now I pushed your cue (Schaft) in Weim and put an excess bending for a couple of millimeters in a plus. On Sunday evening, take off the bending pressure and check the results of editing. Perhaps you have to hold in Vaima longer, ten days, approximately, reducing the gradually forced bending to zero.

Guccio. 20-01-2013 10:09

Master competent did, before my case, no complaints were heard on his work.
As we meet with you and decided, there are nowhere to rush, there are no hurry, let at least a month rule, of course, if you do not deliver any inconvenience!

Bonding wooden products are accounted for both in production and in everyday life. To get a durable and durable connection, it is important to choose a high-quality and suitable adhesive composition. Joinery glue should not only securely fasten a natural tree, but also various construction Materialshaving a wood base. It is often necessary to glue a piece of metal, ceramics, plastics, and so on. This moment is also necessary to take into account when choosing glue. Currently, few people use homemade carpentry mixtures even among professionals. On the construction market A wide range of compositions for working with wood is presented. The following compounds enjoy the greatest demand.

• A polyvinila acetate dispersion is hidden under the designation of PVA glue. It is not toxic, so you can use the product in the premises without exhaust ventilation. PVA glue will dry quickly, withstands high static loads, but is afraid of long stay in a humid environment. Due to the affordable price, it can be used for domestic purposes.
• Polyurethane compositions are much more expensive. But they have several important advantages. The seam is able to withstand high dynamic loads, so the adhesive leg of the chair will not fall off after a while. Glue resistant to moisture, ultraviolet, temperature drops. These qualities allow us to use objects in extreme conditions.
• Smal-based adhesives are in demand from woodworking masters and ordinary homeowners. Many more than once used epoxy, which ensure the strength of the joint connection with other materials. Adhesive compositions of this type are not only not afraid of water, but resistant to the influence of petroleum products and aggressive compounds. When working, it is necessary to take care of the protection of skin cover.
• Modern glue compositions on a synthetic basis are widely used in mass production. wooden products, furniture, windows of doors, etc., completely harmless and have improved characteristics compared to household mixtures. The only drawback can be considered a higher price.

Our review fell the best glue compositions for wood. When drawing up the rating, feedback from domestic consumers was taken into account.

Best Glue based on PVA

PVA glue uses well-deserved demand not only in stationery, but also when working with a tree. This eco-friendly product leaves no traces, has good adhesion, just not able to resist moisture for a long time.

3 Moment PVA universal joiner

The best domestic glue
Country Russia
Average price: 211 rubles. (750 ml)
Rating (2019): 4.8

The best glue of domestic production in our review was the moment of the PVA versatile. It is a water dispersion of PVA. With the help of this glue, you can connect different breeds of wood, as well as building materials such as plywood, MDF, DVP, chipboard, veneer, paper-layered plastic. Details must be pressed to each other by 15-20 minutes using clamp or vice. The final exposure time of the details before the start of use is 24 hours. The joine glue does not color wood, which expands its area of \u200b\u200buse. The composition can be used at a positive temperature in the range of +5 ... 30 ° C.

Professional joiners and home masters highlight such qualities Moment PVA car versatile, as a short time of setting, strength, availability, transparency after drying. The disadvantages should include fear of moisture and low temperatures.

2 Krass PVA PVA D3

The most transparent glue for wood
Country: Poland.
Average price: 195 rub. (500 ml)
Rating (2019): 4.9

In order not to spoil the appearance of the glued parts, the professionals prefer Krass PVA D3 glue. It is suitable for connecting different wood species. The product is used in the production of garden, kitchen furnitureMounting parquet and laminate. The material is in demand and in the manufacture of windows, doors, bars, plywood, veneer and chipboard. Distinctive features PVA glue is water resistance (class D3) and the transparency of the dried layer. In addition, seam has elasticity and durability. Thanks unique properties It is possible to glue even crude wood. There are no organic solvents in the composition, which makes the material is environmentally friendly.

Domestic joiners Foreignly respond to such qualities of Krass PVA D3 PVA D3, as water resistance, crystal seam transparency, elasticity, democratic price. By minuses should be attributed for a long time drying.

1 Kleiberit 303.0.

Waterproof Glue PVA
Country: Germany
Average price: 232 rub. (0.5 kg)
Rating (2019): 4.9

The best technical characteristics It has a waterproof glue KLEIBERIT 303.0. The material occupies a leading position in the construction market, its quality is tested by time. The high-quality product has universal properties, with its help you can fasten various wood, veneer and wood-chip. Distinctive feature It is the possibility of gluing exotic and solid wood. Details should be pressed to each other for 6-10 minutes at a temperature of + 10 ° C. After drying, the glue layer has white colorAnd the frost resistance of it reaches the marker -30 ° C.

Domestic consumers identify such properties of PVA glue Kleiberit 303.0, as water resistance, frost resistance, strength, fast setting. The disadvantages include the need to strict compliance with the requirements of the instruction.

The best polyurethane adhesive compositions

When high strength is required from the adhesive, long-term resistance to mechanical loads, resistance to moisture and negative weather conditions, the best option will be the use of polyurethane composition.

3 AKFIX PA370 D4

Fast drying and excellent heat resistance
Country: Turkey
The average price: 500 rubles. (0.56 l)
Rating (2019): 4.7

Ready to use single-component adhesive AKFIX PA370 on a polyurethane basis is capable of quickly and efficiently glue a tree with metal, concrete, foam, and various plastics. Ideal for repair wooden boats, yachts and boats, due to water resistance and aggressive environment. It should be borne in mind that in the process of drying the glue slightly increases in the amount, increasing the quality of the compound of porous materials.

The glue has proven itself in carpentry production in the manufacture of furniture, windows, doors or layers of wood gluing in complex structures. To obtain the maximum durable compound temperature ambient It should not be below + 5 ° C, and the connected parts are slightly moistened. Not dried glue residues are easily removed by acetone. Limit temperatures in which glue seam does not lose its property from -40 to +100 degrees Celsius.

2 Soudal 66A.

The highest adhesion
Country: Belgium
The average price: 400 rubles. (250 ml)
Rating (2019): 4.9

The highest adhesion boasts the Belgian glue Soudal 66a. It is a polyurethane composition that can withstand harsh operating conditions. The supervodistal material allows you to glue any kinds of wood products, including wet. With it, you can connect wood with most building materials, with the exception of PP and PP. In the process of rejection, the composition is foaming, due to which cracks and irregularities are filled. Durable seam retains its working quality in a wide range of temperatures (-30 ... + 100 ° C). High adhesive ability allows you to apply glue when performing the most complex carpentry and carpentry, both indoors and outside.

Carpenters and joiners praise Soudal 66A glue for excellent adhesion, high compound strength, water resistance. Of the shortcomings, professionals allocate a decent expansion and a high price.

1 Kleiberit 501.0.

Best universal glue
Country: Germany
Average price: 397 rubles. (0.5 kg)
Rating (2019): 4.9

The best universal glue in our review is products from Germany Kleiberit 501.0. The basis of the adhesive was the polyurethane composition, which gives the material such properties such as moisture resistance and heat resistance. The one-component composition is easy to use. It can be used not only for bonding two wooden elements. Various combinations of materials, for example, PVC are possible, mineral plates, ceramics, concrete, etc. It is possible to exploit glued nodes not only indoors, but also on the street in the rain or the scorching sun. Impeccable product quality confirmed international standards (DIN / EN 204, WATT 91). Seall finally hardened after 24 hours.

In the reviews of domestic users prevail positive statements. Kleiberit 501.0 glue is convenient to use, it does not flow, the connection is solid. But it is very difficult to wash your hands from adhesive compositionAlso when working is required good ventilation premises.

The best glue compositions for wood based on resin

Nearby useful qualities It has glue based on various resins. It does not change the color of the tree, it is distinguished by excellent adhesion, has high strength and electrically insulating properties. But when working with it, it is important to ventilate the room well and use personal protective equipment.

3 Glue EDP epoxy

Best price
Country Russia
Average price: 63 rubles (100 g)
Rating (2019): 4.7

Reliable universal means For gluing wood is epoxy adhesive EMP. It is very popular with professionals and lovers thanks to an affordable price. The tool can be used for the manufacture of new products based on wood or the repairs of the failed furniture elements. The seam is characterized by high strength, lack of shrinkage, good adhesive ability, resistance to moisture. The exceptions are only items that have contact with food (dishes, countertops). EDP \u200b\u200bglue is checked for years, its properties do not cause doubts about consumers.

Domestic users from advantages note the low price of EDP glue, exceptional strength and durability of its seam. The composition you can enter various fillers. Of the minuses, there are long-time hardening, getting a muddy seam and inconvenience in work.

2 Uhu Plus EndFest 300

The most durable glue
Country: Germany
The average price: 428 rubles. (2x15 ml)
Rating (2019): 4.9

Superproof abilities have two-component glue Uhu Plus Endfest 300. It is made on the basis of epoxy resinthat allows you to stick to the tree wide spectrum Materials. The exception is the details of the glass, PP and RE. The glue is seized for 90 minutes. Finally, the seam hardens for 12-24 hours, after which it acquires impact strength, resistance to aging and resistance to humidity. To obtain a high-quality working solution, you need to mix both components according to the manufacturer's recommendations. After that, a thorough mixing is made to obtain a homogeneous mass. The prepared glue is applied with a brush or spatula.

Professionals and lovers celebrate a number positive qualities UHU Plus Endfest 300 glue. First of all, superplication is highlighted, resistance to mechanical effects, moisture resistance. The minuses of glue for many users is the need to prepare a working mixture.

1 Titebond Original Wood Glue

Best professional glue
Country: USA
Average price: 195 rub. (236 ml)
Rating (2019): 5.0

For professional activity Claimed Titebond Original Wood Glue glue. The basis of the composition was the emulsion of an aliphatic resin. After drying the seam, it turns out durable, it has a transparent yellowish structure. The film is not afraid of water exposure, it can withstand a strong shock load. The main purpose of the adhesive composition is a combination of wooden products. This product has been particularly well established when gluing a spike-groove type designs. Emulsion deeply penetrates the wood of different breed, forming a solid connection. Besides natural tree With this glue, you can work with parquet, plywood, fiberboard and chipboard. It is convenient to use glue, since the film is immediately seized, and when pressing it quickly harms.

Many professional joiners and builders use Titebond Original Wood Glue glue, characterizing it as the best option for work. The disadvantage can only be called a high price.

Modern glues on a synthetic basis

The specialists of the joiner's specialists use ready-made mixtures with harmless additives that increase the strength of the clutch of surfaces and the duration of operation.

3 FORBO 650 EUROSTAR FASTCOL

High fixation
Country Russia
The average price: 1900 rub. (3 l)
Rating (2019): 4.6

The distinctive feature of the forbo 650 dispersed contact glue is its ability to withstand large dynamic loads on complex surfaces, such as steps and walls. The glue has a lot of versatility and is perfect for a joinery, allowing you to glue a tree with absorbing and absorbing bases.

The glue does not contain solvents and has low emissions. After applying to the surface and its complete drying (about 1 hour), join the glued parts. The quality of adhesion depends on the amount of applied glue, therefore, for a uniform and optimal layer, it is better to use a structural roller, which is included. Thermal-activating glue properties allow separating the glued parts using a construction dryer.

2 Quilosa Bunitex P-55

Does not lose its properties with time
Country: Spain
The average price: 480 rubles. (1 l)
Rating (2019): 4.7

Quilosa Bunitex P-55 multifunctional glue is based on organic polychloroprene mixtures with the addition of synthetic rubber and is capable of creating strong wear-resistant wood compounds with all types of industrial materials or domestic destination. This glue is very often used in carpentry production when gluing products from wood, chipboard panels, corrugated cardboard. In domestic use, glue is the best suitable for laying a cork covering.

The glue should be applied on both surfaces that should be dry smooth and purified from dust. If the surface is porous, it is recommended to apply a preliminary layer that forms a homogeneous film, and to glue the second layer. After the connection, the adhesive is instantly grasped, but the final strength is achieved in a few days. Under all requirements, high quality connecting seam is achieved, which does not lose its properties with time.

1 Titebond III Ultimate Wood Glue 1415

The most harmless glue
Country: USA
The average price: 1000 rubles. (946 ml)
Rating (2019): 5.0

Among a huge selection adhesive mixes For wood, the highest demand for professional carpets uses a single-component Titebond III Ultimate. They can produce gluing any wood breeds with different types Button connections (spikes, grooves, spool, etc.) glue has increased moisture resistance and at the same time easily cleaned with water before drying. The absence of toxic impurities makes it possible to use it in the production of products in contact with food.

The glue is ideal not only for internal, but also for outdoor work, withstanding the high drops of temperatures after soaring. Having itself best density The clutch exceeds the tree itself, without the risk of destruction of the structure to produce final processing of products, and the absence of abrasive impurities will retain the cutting edge of the tool. In terms of its characteristics, Titebond III is the only composition that complies with the Alsy Type 2 moisture standard and, subject to the instructions while working to the quality of this product, there should be no complaints.