It often happens that the user inserts the plug into the outlet to stroke things, but after a few minutes it understands that the iron does not heat up. This does not mean that the device immediately needs to be thrown out, because in many cases it is possible to repair irons and it will not be so difficult as it seems. If you understand a little bit in the technique, you should try to solve the problem yourself, while better decision will be the appeal B. service centerwhere iron repair will be guaranteed professionally. What can cause the iron that I stopped working? Let's consider five reasons that contribute to this.

1. Network cord. One of the main breakdowns of the iron can be considered it is the network cord that, in fact, is inserted into the outlet. To repair irons, in this case it will be necessary to get to the place where contacts with the heating element are connected. When visible faults No, you will have to use the tester and call the cord, it will help determine the worker it or not. If still the network cord became the culprit of the malfunction, you may have to crumble it, or change to a new one.

2. Temperature controller. This detail is the second in line. It is also necessary to check with the help of a transverse, which is attached to the contact group. In case the temperature controller is scrolled towards the circuit of the circuit, the electrical circuit should operate. Light bulb does not burn? We have to clean the contacts with emery paper And check again.

3. Thermal stitch. This element of the scheme is able to fail more often than the power cord. Its main purpose is the disconnection of the electrical circuit when the temperature of the TEN exceeds the nominal value. Using a call, you need to determine the performance of the fuse. If he caused the failure of the iron, it will be necessary to replace it, or even an exception to it from the scheme. As the practice of repairing irons, with normal operation of the temperature regulator, there is no need for a fuse.

4. Heating element (TEN). Another reason for the repair of the iron is required is a malfunction of the Tan. When the device turns on, the light bulb glows, with the sole before the temperature is not heated, the reason is exactly the reason. As previously needed to test the performance of technology. The heating element is fixed to the sole, so when the place of attachment is in-noise, the restoration is not possible faster. If, the TEN is connected to the sole by means of tips, it is possible to repair the iron. To do this, you will have to clean the contacts. If after this iron does not heat further, it is better to buy a new device because new detail It will cost almost the full cost of the device.

5. Evaporation system. When the breakdown lies in the fact that the steamer does not function in the iron, it will take care of the internal cavities of the vaporization. For these purposes, you can use water and vinegar. Another reason for the breakdown breakdown can be a pair of supply button, which in most cases has to be changed.

In any case, if your iron is expensive to contact the specialists who are taken to repair all models of irons in Kiev, and fulfill it professionally.

Instruction

Inspect the Bosch Iron on the other side where the cord comes from. Find the screws located on the back cover. Unscrew the bolts using a suitable screwdriver and remove the lid.

Do not smooth dirty underwear, otherwise the stains can fit at high temperatures even stronger. Better thing Get together again.

The easiest things are smoothed down a bit poor after. Otherwise, use.

Finger along, so it will preserve its form better.

As long as you lay out things on the board, put the iron to the side. It should stand, without leaning the hot surface of anything. Do not even disconnect the iron, you can burn them.

It is important to properly follow the ironing mode for different types material. So, for example, silk is smooth a little iron, while the cloth should remain a little wet. When ironing cotton and flax, set the maximum temperature on the device. The wool should stroke through the wet marley type fabric. Velvet and Velor and are altogether weighing the weight almost cooled iron. It is better not to iron the glitched prints and lace. And for bulk drawings on fabric, the temperature of the iron is better to reduce.

Do not forget to turn off the iron at the end of the ironing. Remove it to your place (let's say, in the closet) you can only when it is completely cooled.

Video on the topic

If you stopped heating the iron, do not hurry to throw it out. After all, the malfunction can be completely empty. To eliminate the inner malfunction, the iron must be disassembled and inspecting. In this article, we just consider the process of disassembling and repairing the iron in details.

Instruction

Iron body is usually difficult to understand. First open the back cover where the wire is connected. Slots of screws holding the lid can be the most different. It all depends on the manufacturer. Sometimes you have to told Nadfil so that it goes.

After removing the lid, check the power cord. Complete it with the tester. You can also connect to iron terminals from 220 V, and then turn on the plug into the network. There is often breaking around the wires there, where the cord enters the body of the iron. Here you should shorten the cord. If the fork and veins of the wires are in order, disconnect from the sole of the upper part of the iron to check the internal elements.

When disassembling the case, you need to find all the screws of the fastener. They can hide anywhere. By revealing the fastening screws, make the latches that you need to squeeze with a knife or screwdriver. Remember what was attached to, as well as in which sequence. Otherwise, you risk not to assemble the iron back or assemble not completely.

After performing all operations, separate the iron housing from the sole. Check with a TEN tester (heating element, mounted along the edges of the sole), thermal stitch and thermostat. They are connected consistently, so there should be no problems.

If you do not have measuring device, Check the fuse with the alternate closure of the segment of the insulated piece of the wire, the ends of which should be cleaned. Turn on this time the wire in, but do not forget about the danger of damage to the current. You can prevent this danger, if you do not touch the current-carrying parts of the iron naked. In the extreme position, the thermostat will open. It turns on with a characteristic click during rotation. With unlocked contacts, you can clean them with the help of the appropriate or strips of sandpaper.

And if the thermal stitch, the thermostat and the power cord is working, the iron can be disposed of or disassembled by spare parts.

Video on the topic

Sources:

• disassembly of an iron

Iron - an indispensable thing in household. Usually we choose this household appliance for a long time, guided by ease of use. And if suddenly I was out of order, it is very sorry to change it to a new one. Was it impossible to give the second life to our assistant and repair it at home?

You will need

• Screwdriver, tester.

Instruction

Disassemble the iron body. First, open the back cover - where the electrical wire is connected. Depending on the specific model, you may encounter screws under different tool. Sometimes it is necessary to search for the desired screwdriver for a long time or removing the appropriate one.

After opening the lid, check the power cord. To do this, use a standard tester or connect to the terminals of the iron cartridge with a conventional light bulb included in the network. If the check revealed a cord break, shorten it or replace it with a new one.

If the wire is not damaged, disconnect the top of the device from the sole to check the internal elements. When disassembling the housing, find all the fastening screws. If latches are provided in the design, gently press them with a screwdriver. Remember what details and in what sequence you disconnect so as not to break your head - where to attach extra parts.

Carefully inspect the internal elements of the iron: heater, thermostat, fuse. Using the Tester, check each item (they are turned on sequentially).

For the prophylactic repair of the thermostat, which can not completely close the contacts, clean them with appropriate or sandpaper.

If the verification revealed the thermal power failure fault, the easiest way to exclude it from electrical circuit, Ravorotiv. Iron It will work properly without this item, which is only an additional protection in case of a thermostat failure. The main thing is after the end of the household appliance, it is timely turned off from the outlet.

After you successfully repaired the iron, collect it in the reverse order. The assembly will be easier if during the disassembly you probably schematically draw its sequence.

Video on the topic

Sources:

Disassemble iron And check all the contacts that are located inside its housing. Special attention Pay for the integrity of the network cord. If the thermostat adjustment is shot down, disassemble iron And install the adjustment mechanism in place. In the case of the brass, just replace it.

You will need

• screwdriver, Passatia, Key Set, Tester

Instruction

If a iron stopped working, disassemble it, unscrewing all the fastening bolts. If the housing is attached to the sole of two nuts, which are recessed into it, use the end key of the appropriate size. Free the contact block and remove the thermostat handle, which is attached to the body with two springs. Just pull the handle from the case irona, and she will take off.

Carefully check all the contacts inside the case if there is a break, clamp the wire into the mount in order to restore the contact. If in irone There is a fuse, check its integrity by connecting the tester to it and call it. If the main temperature controller is working, simply throw away the fuse and shorterate the wiring in the place where it was located, having achieved a reliable contact.

Sound the power wire ironbut. To do this, one of the tester contacts attach to the fork, and the second is alternately to the conclusions in irone. If there is no signal - the problem is in the wire. Cut it as close as possible to contacts and sound. In 99% of cases, contact is broken on the segment of the wire from entering into iron to the contact pad. If the wire is intact, attach it to the contact block, if not - replace it.

If in these nodes everything is fine - inspect the temperature regulator. With its rotation, the contact group with a characteristic click must be activated. Close the contacts and ring the circuit with a tester, if not the chain is broken, with the help of sandpaper zero, determine the contacts.

If everything is good, then the most unpleasant reason Breakfast - burned Ten ironbut. Since it is pressed into the sole, it is not possible to change it, which means that iron hopelessly spoiled. Just in case, inspect its conclusions to connect it to the current source, sometimes they are oxidized, and contact disappears. Check them and sound the TEN, if the contact appeared, iron will work.

Video on the topic

Such a device like iron entered and rooted tightly in modern life. Almost every mistress is familiar with the process of ironing linen, and with modern models of irons, he became easier and more pleasant, because, unlike predecessors, they are easy and compact.

Instruction

The first differed in serious weight characteristics and reached almost five kilograms. The process of ironing linen with them was very not simple and long. but modern technologies allowed to create lightweight devices with wires and without them. Today the market represents a huge range of this product of different types and models. Principles of operation of wireless and wired irons are similar. Both types of irons are artificially heated and in contact with the surface that it is necessary to stroke, and it is heated, eliminating all the formed irregularities when moving.

Heating out soles of the iron since a long time, sought different ways. The first mention of these devices appeared in the 14th century. At this time, irons appeared, which were heated with coal, covered in the lower part of their design. On the sides of such irons, small holes were located, which gave air intake to fuel. Then an alcohol iron, based on alcohol, appeared. In order for the equipment to heat up to the temperature of the ironing, it was necessary to simply set fire.

With the development of physics and determining methods of application electrical Energy And its conversion on the market has the usual irons today with electrical heating. Inside them were installed spirals that increase their temperature from the power grid - such spirals called general concept "heating element". The temperature of the heating element is communicated with the sole of the iron, which also heats up. The thermostat turns on and disconnects the helix depending on the specified temperature.

Wireless irons are very comfortable, because they can be stroking even big things, without fear that the cord is confused or twisted, and it is not necessary to bring the ironing board closer to the outlet. A variety of such models is huge, so even a person choosing a thing from the average price category will be able to evaluate dozens of different devices.

Basic parameters of wireless irons

Wireless irons are complemented by a special stand. The essence of their work is simple: you need to put the iron on the stand included in the network, wait a bit until the sole is warm and then stroke. When the iron cools, you need to put it again to "charge". When choosing a device, pay attention to the time of warming up and cooling the sole. Some models have to return to the stand every 30-40 seconds and wait for 10 seconds until the iron reaches the desired temperature. Others can work without "" for 2-3. The more often you have to iron, the more convenient for you will be the second option.

Remember that the higher the power of the wireless iron, the more expensive it is. It is important to find a compromise between convenience and price.

Some irons can be converted from wireless to wired and back due to a special design. If you want a model 2 in 1, it perfect option For you. Also pay attention to the functioning of the stand: some models, alas, do not allow a beep, and it may irritate. If you fear that you will forget to return the iron to the place to warm up, the device's pilot will be as if the way. The same outsided sounds annoy it better to search quiet model.

Additional nuances to pay attention to

Some irons are complemented by a vaporization function. If you plan to disappear things, either ironing a hard fabric, prefer exactly such an option. The steamer will cost more than the usual wireless model, but it will be more functional.

It is important that the steam wireless iron has self-cleaning sole and a special system that does not allow large droplets of water to the fabric.

Pay attention to the set of functions. You can use iron with dry, vertical steaming modes, intelligent adjustment under the type of fabric, scale protection system. The more functions of the device, the more expensive it is, so it is important to choose the options that you really need. Read

Currently exists great amount irons OT. different manufacturers. Sooner or later, various damages are possible, in which it is required to repair the iron. It is especially unpleasant when the iron breaks at the most inopportune moment.

The main breakdown, which is most often observed in most irons, is the cessation of heating. When breakdown, first of all, the iron must be disassembled. The disassembly of the body is the process is more complicated than the subsequent repair. Nevertheless, it is necessary to disassemble it, and, first, the back cover opens where the electric cord is connected. Usually, the cover is screwed with screws.

With the lid open, first of all, the service of the electric cord is checked. As a rule, the cord is checked with. In another case, the cartridge with a regular 220 volt light bulb connects to the terminals where the cord begins, after which the plug is turned on into the outlet.

The main cause of a malfunction

Most often lived cord happens at the site of entering the case. In such a situation, the electric cord can be simply shorted. If it turns out that the cord and plug are in good condition, then you need to check the condition of the internal elements of the iron.

To do this, the upper part is disconnected from the sole, and it is very important to detect all the places of fastening using screws. Screws can be located in any areas, for example, under the handle of the temperature regulator, under the lid of the casting hole or under the cap of the indicator light. In addition to screws, additional fasteners may be present in the form of a latch, neatly pressed with a screwdriver. When disassembly, you should also remember the mount and location of the nodes so that it does not occur during the subsequent assembly of the iron.

Fault of heating elements

Inside the iron is the main element for heating, mounted along the edges of the sole. In addition, there is a thermostat with a thermal stitch, pressed against the sole with a bracket. Each element is checked by a tester, after which the solution is made on repairing or replacing parts. If the contacts of the thermostat cannot be called, it is possible that the problem is solved by stripping their sandpaper or supfil. If it happened, it is excluded from the scheme. With normal operation of the iron without a fuse, the defective part is replaced.

When the iron repair is completed, it must be assembled in the same sequence, which he understood.

Tefal avoids producing ordinary irons. All steam. One of the few firms that presented in the market wireless models. With some share of confidence, let's say: Tefal divides the first second place with Philips in this segment. The only wireless irons who overturved Russia. The design is much different, the basis is the former fundamental elements. Soles are the same. Precipating the similarity of the heating elements. It is not surprising that the repair of the TEFAL Iron is striving to fulfill many. Leader sales of the domestic market.

Iron design

Starting with the simplest Soviet Iron, the design includes the following elements:

1. Case with a regulator.
2. Sole.
3. Spiral spiral in the sole.
4. Set of electrical connections.

Boyler, equipped with ane

An ordinary iron is equipped with two removable items. Sole, rear wall with cord. Always put bolts, art consists of finding fasteners. Old Soviet heads of heads hid under the knob of the regulator. Moreover, to remove the last sometimes problem. More often managed to make the necessary slotted screwdriver skillful hands. The back wall could be attached by a bolt or just snap. In the latter case, the compound became short-lived. But behind the back wall you can detect the block where the network cord is mounted. Cable malfunction provokes 20% of faults. Accordingly, I invonize the veins immediately.

Repair of irons is convenient to carry out, throwing the Chinese tester. The regulator changes the tension of the bimetallic plate. Remove the handle, try to understand whether the sensor is working as much smoothly. If potholes are formed, some areas are poorly missed electricitywill be immediately visible. Of course, the regulators are devoid of irons, equipped with the function of automatic adjustment under the fabric, in most cases, as half a century ago, the round rotating plate is located under the handle. And what a sole.

Bolts are unscrewed, we obtain access to the heating element, the regulator mechanism. At modern irons, the body hides a minimum of two interesting details:

1. Water boiler.
2. Sprayer.

Thinking about us iron tefal

The first takes up an arbitrary place, is determined by the design. The second chopped nose. Of course, away from the sole. The scheme of action is as follows:

• reaches the desired temperature of the sole;
• the liquid from the tank is automatically fed;
• under the action of temperature, water becomes a ferry;
• steam punch is reset by a special button puming a little large quantity liquids.

The calorific value of the Iron sole below is infinity. Between two steam blows time will pass. There are schemes where emissions go split short intervals by twos, three. As with semi-automatic shooting. Then - an indispensable pause. There are devices with preheating water boiler. It is clear, no boiler inside there, the water heater, however, is worth it. Highel temperature will make it easier to get steam. Wonderful Wireless Idows Freemove, working cycles. Heating - 4 seconds, work 25 seconds. Warmly sprinkled with water, water (water batteries based on private house pools will help explain the principle of operation). The process is controlled by automation, enough energy is accumulated, the green light begins to flash, testifying: you can begin to stroke.

About wireless irons can be said separately. The design is slightly different from the usual steam. Many manufacturers have an option with the fastening of the cord, however, the peculiarity of the tefal irons: wireless means - no wire.

Standard iron service

Before starting repairing the iron of the tefal with your own hands, track the light indication. Light bulbs, diodes that help to catch the meaning of the problem are built in models. Network, which does not want to burn, testifies: No food. The case probably spoiled the cord. The heating is not lit, faulty: contact, spiral. Easily check. In good condition, the resistance of the heater is calculated according to the law of Ohm. Passport power is taken by the current voltage of our country 230 volts. We divide the first square of the second, it turns out the desired resistance in Omah.

Modern iron contains a thermal stitch. The accessory in love with the sole, tear the connection when the parameters exceed the norm. Irons that fit under the type of fabric are devoid of lack. It is allowed to leave on the ironing board, will cost. Another thing is a broken scheme. Fuses meet bimetallic and wires. The latter are called disposable: require replacement. Electric kettle protects, triggering is configured at a lower temperature.

Iron refuses to warm - make sure the integrity of the cord, we investigate the heating element with a tester. Automation of complex irons refuses, do a ring. Check the relay, thyristors, controlling the power part.

Pay attention to the thermostator. Contacts of a mechanical runner Start a graphite of a simple pencil. Improve glide. The simplest regulator changes the response temperature of the bimetallic relay. Complex - forms a resistive divider, performing a row. Is not best MethodThe power is lost. Graphite fearlessly tolerates heating, serve as a lubricant. Contacts can be resurrected in small skirt.

Cleaning Iron from scale

5 percent solution pour a centimeter in the dishes. Inside, put the top of the coins so as not to overlap none of the holes in the sole. Weep on top of iron. Naturally, we turn off the device from the outlet. Water boats, cool. Repeat the cycle 2 - 4 times, wash the sole to flush. Most irons are equipped with self-cleaning function. Fill inside the water, holding the sole horizontally over the sink, press the button, giving the liquids to drain. The recipe cleans the iron holes, lower moves. Conducting the procedure periodically, coins will be cleaned, avoid the appearance of rust on things.

Try to use distilled water. In addition to a typical filter dedovsky method. Boil the water! Salt of rigidity will gather a spiral of an electric kettle, dirt is not as terrible as on clothes. In irons with boilers, vinegar is used in normal mode for periodic cleaning. The vehicle is universal, enjoy love to recommend manufacturers of exciputers, steam cleaners, other household appliances. Remember: It is impossible to clean rubber things with vinegar. Concerns labels washing and dishwashers, water heaters. Sprayer rubber parts contains. Vinegar is harmful to the node. It will cause premature aging of the product, wear details. Independent repair of irons Tefal will lead to a new headache.

Sprinkler sometimes have to clean. Water across the nose forward splashing refuses - the hole has been scored. Avoid applying vinegar lemonic acidChemicals. Carefully use matches, pins, other trifles, buy a means against screaming washing, dishwashers. Removes the precipitate formed by powders, air conditioning on the walls of the tank. Dishwasher cleaning agent washing machines Perfect for sprinkler. The rest brushes acetic acid. It will be useful to read the instructions, the practice shows: the paper usually goes directly to the basket.

Output

Repair of irons with a steam generator in principle is not different from ordinary. A loud word simply means water tank with a valve, activated automatics, button. The location of the sole hole allows you to study the built-in steam generator. Lined the edge: water just drips from the tank. When the holes were squeezed, inside flowing heater or boiler. The road to the sole water becomes a ferry.

Although Iron and not the most expensive appliances, but when it breaks, you can not run right away for the new one. First, try to repair it yourself. Iron repair with your own hands - you can start a home electrician career. Simple schememinimum elements.

If we talk about electricuga, they are three types:

The most common - irons with swaps, it is its repair and will consider further. First you should familiarize yourself with its device. So the repair of the iron will be easier. Knowing the composition of the device and the purpose of its parts can be called possible reasons Problems.

If we speak in general terms, each iron consists of a housing, handle, thermostat and soles with holes through which steam is served in the iron zone. To maintain the evaporation mode into the iron body, water tank is built in, there are also the intensity intensity regulators.

Device of the sppache system

Modern electric irons of this type have several swap modes. To understand how everything works should be considered, as it is all arranged. After all, often repairing the iron is needed not because the iron is not heated, but because there are no steam. And it is important to understand what it is the case.

IN modern models There are three quarption modes that have individual buttons. Each button drives its pump, which, depending on the settings, supplies the required amount of water. There are modes and pumps:

More simple models (previous generation) usually have a sprinkler and an evaporation mode. They have a slightly different building. The first difference - the heating regulator of the sole is transferred to the handle (however, it is not always), a steam controller is also located on the handle, but it is made in the form of a rotary disk.

The sprinkler button, in such models of irons, is between temperature regulators and steam.

Iron repair is impossible without an electrical circuit. As you can see schematic scheme The electricual is not much different from the scheme of the kettle or boiler. The main differences in the form of heating elements and other "additional" devices.

There are only a few elements in the diagram: connecting block, heating element, thermostat and thermal protection. Thermal protection can be different. In the simplest case, this is a fuse. In more complex models, this is a shutdown device when overheating. Since the elements of the scheme is a bit, the repair of the iron is not the most difficult task.

How to disassemble the iron

If the iron does not work, the first thing to do is to disassemble it. It is not as easy as it seems - too many models, each of which can have their own "chips". Moreover, different models of one manufacturer can understand differently. However, there is general principles and rules:

• Remove the back handle cover. This allows you to get to the terminal block. With some damage (problems with the cord or failure of the Tan), this is sufficient and the iron is further not needed.

  
  
  
  
  

• Remove the pair feed buttons, steam shock, sprinkler, thermostat. Often they can be removed simply pulling the top. Some are equipped with latches that need to make something thin - a regular screwdriver is suitable. little size, You can try to use a nail file, a plastic strip (you can cut off from an old unnecessary plastic card).

  

• Screw all the screws that you see.
• In many models of irons, the handle consists of two parts. The top can hold on one or two screws and latches. It is possible at all without screw - only on latches. After removing this part, you get access to other screws holding the housing.

The process of iron disassembly does not require the use of force. If "does not go," you need to carefully see what and where it keeps. And you should not disassemble it until the end - it is not always necessary.

Check the most simple

Often the iron does not work due to problems with the cord. When operating, it is often bent, insulation is damaged in the folds of bend, they can even appear sparks. Because the first step is independent repairs Iron - inspection and cord transvelon. For the transvers, you need a multimeter (how to work with it).

Disassemble the iron is the very beginning

Checking electric shuffle

Sometimes, to make sure that the problem is in the cord, you can turn on the iron to the network. If everything is fine, the indicator lamp lights up. This is usually a green LED. By all, it burns constantly or periodically goes out and let's track the condition of the cord. It is twist and bending, paying attention to the state of the signal light bulb. If it flashes, then the power cord is really to blame. It is better to replace it, but if you wish, you can find a problem space (often it is visually easily determined) and correct the situation.

If these are insulation problems, and the conductor itself is a whole, using the isolate eliminate the malfunction. If the wires are damaged, they are cut, connected in a new way using, the connection location is isolated. This repair is a temporary measure, as it is soon again the problems will appear - not far from the "renovated" place. Therefore, the cord is still better replaced.

Terminals and contacts

If there is no external damage to the cord, and it does not work, you have to disassemble the iron. At the first stage of difficulties, it is usually not happening - there is one bolt from behind. This is perhaps the only fastener that cannot be hidden. We unscrew it, remove the lid.

Remove the back cover is usually not difficult - one bolt

Under the back cover, the terminal block is hidden, to which the wires from the thermostat and the tan are suitable, our network cord is connected on the other. Terminal block May look different. Some manufacturers like Bosch) it is hidden under a plastic lid. The lid should be removed. How to get to it - depends on the model. Sometimes it is enough to pry and pull sometimes you have to shoot some details. It is important to get to contacts.

Often the reason that the iron is not heated is hidden not in a penny, but in the fact that contacts clogged or oxidized. Sometimes water hits the contacts (capacity flows), sometimes dust socks there, sometimes it simply weakened the contact. If there is one of these problems - eliminate it. Perhaps the repair of the Iron will end with their own hands.

If you are going to remove the wires from the contacts, take a picture as it was. Less problems when assembling. Human memory is an unreliable thing. The photo is much more reliable.

Checking the cord on the integrity of the wires

If the contacts are normal, clean, nick the cord on the integrity of the wires. We take the tester / multimeter, put in the transverse mode. One dipstick touches the cord pin, the second "go through" the wires on the terminal block. If the wire is a whole, one of the pairs should "ring" - you must hear a beep.

Iron cord transvelca

The iron cord is a three-wire, two wires go to the cord pins, and the third - green or yellow-green - ground. On the iron fork, this is a metal plate. Touching it and green wire on the block, you must hear a "peak" of the multimeter. If at least one wire is "not ringing", changing the cord.

Temperature regulator

How does he work? It consists of three main parts: the rod attached to the contact plates and the bimetallic plate. The bimetallic plate is heated from the sole of the iron. With increasing temperature, it is heated, strung out. At a certain temperature, it will be deployed so much that the contacts turn off, turning off the power. When the iron cools, it takes the initial state, the contacts are closed again, the iron begins to warm again.

First you need to check whether it works at all. Screw it from one extreme position to another. One of the provisions should result in a characteristic click, which makes the closed contacts. It is through them that feeds on a tan of iron. Leaving the thermostat in this position, check the presence of electrical contact.

Two contacts depart from the temperature controller (they are connected to the wires that go to the TEN). To them and touch the arrivals of the multimeter (transverse mode). If fries - everything is fine. But, putting a regulator to another extreme position, you must get a "cliff" - contacts should open. In this case, this node works fine.

It does not hurt and visual control - maybe they are burned, oxidized, weakened. If there is a scale, dirt, rust, they can be carefully cleaned. To do this, you can use a strip of sandpaper with a very small grain or nail file. Do not dilute much - do not spire contacts completely. During cleaning, try to flex the plates at a minimum - so as not to weaken the contact.

Sometimes the regulator turns hard. Capturing it with pliers or passages, rotate it there and here until they achieve a smoother course. After that, you need to take a simple pencil and grate a knot graphite. It does not hit when high temperatures And has good lubricating properties.

After all manipulations again, check the presence of contact in the position of the thermostat "Inclusive". If everything is fine, you can try to connect the iron and check its performance. Perhaps the repair of the iron is finished with their own hands. If not - go further.

Fuse

Thermal stations are disposable and reusable. Disposable when the critical temperature is exceeded. After that, the iron does not turn on and restore its performance only by replacing a disposable fuse.

Reusable is made on the basis of the same bimetallic plate and works as well. This node increases the reliability of the iron - does not turn into it, if, suddenly, did not work the thermostat. Most often, the cause of the non-working iron is the burning of the fuse. This is about 50% of cases of the exit of this device. It happens if the thermostat, and the reusable fuse did not turn off the iron.

You can get to the fuse only completely removing the housing. We find it, touch the arches of the multimeter on both sides. If there are no sounds, he is guilty. We fall out the faulty, put a similar one. You can still put a "bug" instead - to have a piece of wire. But at the next failure, there is already a TEN, and not a fuse. Then the repair of the iron will end with the purchase of the new - the price of the sole is comparable to the cost of a new iron.

Iron sole problems (TEN + water tank)

In many models of the TEN Iron, together with the water capacity, is smeared in a single case. Problems with one of these parts lead to one - to buy a new iron. The replacement of the sole is inexpedient, as this spare part is a slightly less than a new iron. Even if you decide to change the sole, there is no guarantee that you will find the right thing you need - the market changes quickly, the models are removed from production, they are not discharged on them. In general, if you got the iron in independent repair before this stage, most likely, go to the store for a new one.

There is only a small percentage of cases when the workability of the sole can be restored - if the contacts were oxidized so much that the contact was disappeared. We find these contacts, carefully cleaned and crimp. Next, we carry out measurements.

Test multimeter to resistance measurement mode. In the irons, Tan usually have a resistance of about 250 ohms (more precisely look in the passport), so the measurement limit is 1000 ohms. If the resistance is somewhere within these limits - everything is fine. If it shows "infinity" - the heating element has blocked. As already talked, the replacement of the meaning does not have, more practical to buy a new iron.

The same way out is a trip for a new iron - maybe in a situation with a good heating element. This happens if the water tank was deformed. It can break or inflate. In any case, the iron turns out to be inoperable, although the electrical part is "normal". This is damage - problems with water tank - occurs when large quantities scale. It is easier to prevent than eliminating. It is necessary to pour water into the iron with a small amount of salts. Yes, manufacturers write that you can pour water from under the tap. It will work out its warranty period. And then buy a new one.

What to do if steam does not come out

Couple does not go out. Usually, if the holes in the sole is clogged with salts. This will not happen if using distilled water (perfect) passed through filters or at least boiled.

Clear iron from scale is easy. To do this, take a metal or heat-resistant container into which it can be put on the bottom. In water wept citric acid (1 tablespoon on a glass of water) or vinegar (1 cup per 1 liter). The steam controller is set to the maximum, we set the iron so that its back is slightly above the nose. You can use conventional coins as stands.

Pour solution. The fluid should cover the platform by about 1-1.5 cm. We carry the container with the iron on the slab, bring to a boil, turn off for 20-30 minutes, turn on again. Such cycles are repeated 3-4 times. After this procedure, all the holes and water containers are cleaned. True, while the entire sediment comes out, traces can remain on the underwear.

On this iron repair is finished with their own hands. If it still does not work, carefully inspect all the elements of the system again. They are not so much - cord and shoe, thermostat, fuses, tan.