With the onset of cold weather, different heating appliances... In addition to comfort, they also create some problems - they dry the air in the room, which causes problems with well-being. To avoid this, the air in the room must be humidified. Stores are stocked with various humidifiers, but these are often not affordable. Therefore, such an apparatus can and should be designed by oneself. Learn how to make a humidifier at home.

Master class: a humidifier from a plastic bottle

Homemade humidifiers can be as simple as made from handy tools or more sophisticated tools. The basic principle of the humidifier is water evaporation. The more efficiently the water evaporates, the more comfortable it will breathe in the room.

The devices use different ways evaporation of water is both cold vapor, in which water is dispersed using a spray gun and a fine mesh, and using heating element when water under the influence of temperature evaporates into air, and with the help of ultrasound, which turns water into mist.

The most elementary room humidifier is a container with water standing near heating devices, of which there may be several. The disadvantage of this method is very low efficiency, because the water from the container evaporates very slowly, and you don't feel any special result.

A more effective device is one that can be built from an ordinary one and a half to two liter bottle of water, two pieces of dense material, a gauze cut, scotch tape. The structure is mounted on the outgoing battery central heating pipes. Assembly procedure: a rectangle with a length of 10-12 cm and a clearance of 5-7 cm is cut on the side of the bottle. Next, you need to take two pieces of fabric of such length so that it is convenient to hang the bottle from them to the radiator pipe. For greater strength and reliability, pieces of fabric can be attached to the bottle with tape.

The next step is to fold a large piece of gauze, at least a meter long, to make a tape about 10 cm wide. One edge of this tape is lowered into a gap in the bottle, and the other is wrapped around a pipe in a spiral. Two tapes can be used to enhance evaporation. The hanging bottle is filled with water and the free humidifier works!

Photo easy way humidify the air

To make a more modernized humidifier from a bottle, you will need computer cooler, scotch tape, large-volume plastic bottle (from 5 liters). The top of the bottle needs to be cut off so that a cooler can be installed. They fix it with tape or electrical tape, and for greater strength and reliability, it can be fixed on a sheet of thick paper. Water is poured into the bottle, the cooler is connected to the mains, and the air humidifier is working.

It is worth noting that all of the above methods of air humidification are not highly effective, but they are quite suitable as an ambulance or for small rooms, because comfortable air indoors in winter - a component of well-being. Knowing how to make a bottle humidifier at home can save you money on expensive equipment and at the same time humidify the air well. own apartment do it yourself.

If there is dry air in the room, and there is not enough money to buy a humidifier, then you can solve this problem by spending just a couple of hours of free time. In principle, it is not difficult at home to make a humidifier from plastic bottle... Of course, in appearance the case will not be as beautiful as that of the models on sale, but it will perform the humidification function at a decent level. For your information, the humidity in the room should be between 40 and 60%.

Option # 1 Bun with a volume of 6 l

To create a humidifier you will need:

• plastic bottle for 6 liters;
• fan from an old computer;
• wire with a plug for 220 V.

We take a plastic bottle of 6 liters. Taking into account that the water will be poured about 1/3 of the bottle, we cut 4 holes in the form of windows slightly above the water level. They should be placed horizontally on each wall, opposite each other. That is, one small window will be placed on each side of the plastic bottle.

Important! Windows don't have to be large. In the future, they will be needed in order for air to escape from the humidifier.

It will be much easier to pour water into the container through the windows. Now you need to cut off the neck. Moreover, cut it off so that a fan from a computer can be mounted on the top. It is worth calculating the diameter of the bottle correctly. To do this, you need to step back from the neck of the plastic bottle and cut off the top completely.

Further, in the upper part of the container, in the corners we make 4 holes. This is necessary in order to secure the fan. The device can be taken from an old computer. Such fans work from a regular 220 V network. Using a soldering iron, it is necessary to remove the remnants of old wires from the contacts. We use the usual plug and wire, designed for 220 V.

Strip the ends of the wires 0.5 cm. They need to be coated with a soldering iron with a thin layer of solder. For this, rosin is used. So that the user is not impressed in the future electric shock, it is worth putting on 2 pieces of heat-shrink tubing on the contacts. Only now the contacts are soldered to the fan. When they are soldered, we hide this part of the wires with the help of a heat shrink tube. To fix the tube on the wire, it should be warmed up with the side of the soldering iron. When heated, it shrinks and fits the contacts well.

Important! The air supply from the switched on fan must be directed towards interior plastic bottle. That is, inside our humidifier.

To do this, it is necessary to determine in which direction the fan is blowing. We plug it in and use a sheet of paper to determine where the air flow is directed. We disconnect the device from the network for a while. With four pieces of soft copper wire we fix the fan case at the very top of our plastic bottle. The wire is threaded through the pre-drilled holes in the walls of the humidifier. After fixing, the excess wire is removed with wire cutters.

If the fan does not closely match the diameter of the bottle, do not be upset, the main thing is to fix it correctly on four sides with the help of a wire. In any case, with the help of these slots, the forced supply air will be expelled from the can. When turned on, do not touch the fan blades with your fingers. It is quite powerful and this rash action can result in injury.

Pour water into the appliance through the window in the wall. Turn on homemade device to the network. After an hour of operation of such a humidifier in the room average size 15-18 m2 air humidity will rise significantly.

Important! The device connected to the network must stand on a flat, stable surface out of the reach of children.

Option # 2 Bottle of 1.5 l

Bottle over radiator in horizontal position - simple free humidifier

We need:

• plastic bottle 1.5 l;
• scissors;
• long strip of natural fabric,
• Scotch

In the middle of the bottle, on one of the walls, it is necessary to cut a hole in the form of a square. It should be medium in size. Close the neck of the bottle with a lid. Use small lengths of fabric to tie the bottle horizontally. The container should be located with the window up to the pipe or battery. To prevent the fabric from slipping off the smooth surface of the plastic, tape can be used. Pour water through the hole you made. Air humidifier with bottle underneath hot pipe, near the battery, will humidify the air in the house due to the intense evaporation of water.

Part of the bandage can be lowered into the window so that it gets wet on one side, and put the other side on the battery. This option will allow you to quickly and efficiently evaporate moisture.

You can use a similar humidifier option. However, in this design, a window is not cut through on one side of the bottle, but many small holes are made using a soldering iron.

Important! Only one side of a plastic bottle resembles a sieve. The opposite wall remains solid.

We collect water in such a humidifier, close it with a lid. The bottle can be placed horizontally on the battery. It is important that the holes are above the water. Water vapor will escape through them during evaporation. You can hang such a structure with tape from the pipe.

Option # 3 Radiator suspension

A 1.5 liter bottle can be used to make a hanging humidifier on a battery

There is 1 more option with which you can make a do-it-yourself air humidifier from a plastic bottle. For this you will need:

• plastic bottle of any size;
• wire;
• scissors.

Use scissors to cut half of the bottle. On the sides of the container, make several holes through which the wire will be threaded. Alternatively, with a thick wire, you can attach it to a pipe or battery, with which such a plastic humidifier will be fixed. It remains only to pour water and watch when it evaporates.

Option # 4 Pots with expanded clay

Take plastic bottles of 2-6 liters. Cut them in half. At the bottom, at the bottom, use a soldering iron to make 3 small holes. Put a little expanded clay at the bottom, cover with earth. It is necessary to plant cyperuses in such flowerpots. This plant loves moisture and, with good watering, can evaporate up to three liters of water per day. If you put several pots with such a plant in a room, the air will be constantly humid. However, other flowers can be planted in such original pots, the main thing is not to forget to spray their leaves with a spray bottle.

Expanded clay is an excellent material for a homemade humidifier

The last thing you can do from a seemingly completely unnecessary empty container is to cut the top off. Draw clean water and place it all over the room. Very basic but effective method humidify the air. Spending only 15 minutes of free time, it is easy to create a good microclimate in the apartment in the winter.

Important! Alternatively, you can combine several humidification techniques, then the humidity in the room will surely increase. However, do not forget that brute force is also bad. In the house, this can cause condensation on the windows or, even worse, mold. Therefore, in any case, when humidifying the air, follow the readings of the hygrometer. Ventilation is also an important factor for a good microclimate in the house. It must be done regularly, no matter what time of the year.

An important point when using humidifiers is that they should not be standing on the floor. They must be placed on a stool or chair. Alternatively, make a shelf for them. If you neglect this advice, a puddle will form on the floor. This is because water is heavier than air, so it will settle down below.

The characteristics of the air in a room determine the health status of its occupants. Therefore, sufficient moisture is necessary, which can be achieved with the help of a special device. It is not cheap, but if desired, it is made at home. It is really possible to humidify the air in the apartment with your own hands, the main thing is to choose a simple design.

How to make a humidifier at home

Quick way to achieve the desired room humidity - hang a damp towel on the door, which should be changed regularly as it dries. For an apartment and especially a children's room, this is great option do it yourself humidification, but troublesome and costly in terms of water consumption. Better to dohomemade humidifieron batteries or power it from the mains. So it will last longer, and it will bring much less hassle during operation. There are many videos and photos on the Internet by which you can construct the necessary model, but for the first time it is better to enlist the help of a specialist.

Diy air humidifier diagram

Structurally, such a device consists of three blocks, each of which has its own unique purpose. For example, the evaporator unit resembles an incubator, but is a water tank, outlet and fan. The electronic unit consists of sensors, a transistor key, a microcontroller. The last component of the unit is required to supply voltageto the air humidification circuit, and its main parameters are as follows: 220 V - at the input, 12 V - at the output with a load of 3A on the network.

The 12V output voltage is optimal for starting and smooth operation of the electronics. Maximum permissible load- 3A, with large parameters, it will constantly "knock out plugs" of the lighting panel.Air humidifier power supplywith his own hands, he turns on the stabilizer, which accepts the voltage, reduces it, at the output gives the desired value to turn the electronics circuit into operation. It is appropriate to buy an L7805 stabilizer, while using an additional 5V output. For household purposes it is a good option, however, to implement it with your own hands, a diagram is needed.

Homemade humidifier

To achieve the required humidity, it is not at all necessary to purchase expensive equipment from stores, you can make an air humidifier at home with your own hands. Such a budget option works no less efficiently, but it takes time, ingenuity, patience and endurance to make it.Homemade humidifier air with your own handsreleases portions of moist air, which is enough to create favorable climatic conditions rooms, living quarters. To maintain humidity, you can choose one of the devices below.

DIY bottle humidifier

This is a room option that is not visible on the radiator by the window.DIY home humidifiereven a teenager will make a plastic bottle, you must follow the prescribed instructions. The proposed method is often used by young parents when providing favorable conditions life for a newborn person. The sequence of actions is as follows:

1. Take a plastic bottle and cut a 15 by 20 cm "window" in it with scissors on the side wall.
2. Hang the container on the battery on the bandages so that the hand-made "window" is on top. It is important to thread the gauze through the holes in such a way that it is regularly saturated with moisture.
3. To increase the humidity of the room, it is necessary to constantly add liquid to the plastic tank, which gradually evaporates from the heat of the battery. This rule will soon become a habit.
4. Enjoy unlimited time slot. At the same time, do not forget to pour settled water into a plastic bottle, while the radiators of the battery must maintain heat.
5. Install this home-made device on a battery so that small children, as they grow up, cannot reach it and use it for other purposes.

Battery humidifier

If the option with a plastic bottle is not suitable, another method is known to get rid of dry air, its sufficient humidification in a small living room. You can use a ceramic cup or vase, fill it with water and put it on the radiator to warm up. In this way, you can create a favorable atmosphere of humidity in the apartment, but not in the office. The original ceramic container can be hung, making it an appropriate decor element.

Homemade battery humidifierheating is distinguished by its compactness and safe evaporation temperature of the liquid. There is no noise during operation, unlike disc models, there is no need to comply with the conditions when choosing the quality of water. It is allowed to add a few drops of your favorite essential oil to the composition. On industrial enterprises more powerful devices are needed to humidify the air, homemade products are not suitable. Otherwise harmful substances negatively affect health.

DIY ultrasonic humidifier

Such a device cannot be created from scrap materials; additional details are required. You can buy them in a specialized store, or disassemble unnecessary household appliances which has already stopped working. To combat increased dryness of the air and raise its humidity indicator, it is required to act in a given sequence:

1. Prepare an ultrasonic transducer, a plastic container for 10 liters, a cooler from a computer, a power supply, a plastic cup, aluminum corner, corrugation, plastic cup and stabilizer.
2. Make several holes in the plastic container so that the fan mount, the converter wire, the output wire will fit in them. Install the corrugation directly after attaching the fan itself.
3. Insert a bagel from a toy pyramid, suitable in size, into a plastic cup, secure a piece of fabric on top with an elastic band. This is a kind of filter, it remains only to bring in homemade scheme power supply unit and ultrasonic transducer.
4. DIY ultrasonic humidifierworks on the basis of the piezoelectric effect, therefore, it is not required to additionally use a liquid to evaporate humid air. Steam is produced without the participation of the electrolysis process.

1. Cut off a piece of dense fabric, then tie it tightly to metal pipe so as to restrict the exit of dry air.
2. Hang the pipe at the height of the floor lamp in such a way that it is opposite a working floor type fan.
3. All that remains is to moisten the fabric and turn on the fan, increase the air flow. In this way, a cleaned and humidified air stream enters the living space through the pipe.
4. It is necessary to control the moisture content of the matter so that the home-made unit does not work in vain, otherwise dry air will reappear.

Many ordinary people, in order not to spoil the aesthetics of the interior, are keenly interested in how to replace a humidifier at home, and whether it is possible. Not everyone can make a structure with their own hands, therefore they are in search of a worthy alternative. Alternatively, you can arrange a room artificial fountain, put an aquarium with fish or a flower on the windowsill. You can do other models of home humidifiers with your own hands.

Video: Home steam humidifier

Tracking the level of humidity in the room is important for the well-being of households and for the plants and animals living in it. Warm dry air provokes dryness of the nasal mucosa, causes discomfort during the day, sleep disturbances. It is dangerous for people with chronic diseases, allergies, and small children.

When the first signs of the need to humidify the air are detected, experts advise to ventilate the room, try to lower the temperature to 18-20 degrees, and create conditions for achieving optimal humidity. If such measures are not enough, a special structure with moisture evaporation can be made. Such structures not only humidify the air, but also scent the room, and can also decorate the interior.

• Show all

  The need and role of a humidifier

  Before making a humidifier, you need to figure out what level of room humidification is required. Normal air humidity is difficult to maintain during natural heat in summer and winter period enhanced work of radiators. District heating significantly dries the air, makes breathing difficult, interferes with the normal development, growth and flowering of plants.

  All humidifiers are aimed at implementing the main function - maintaining the humidity level in the living room at a level of 40-70%, since it is this indicator that is recognized as optimal for humans

  Additional air humidification issues are in some special cases:

  • a large number of plants in the room;
  • greenhouse maintenance;
  • cultivation of various cultivated plants, seedlings, mushrooms;
  • work in industrial premises typography.

  It is especially important to have a humidifier in the house where there is a small child, since his body is still imperfect and requires special conditions for normal growth and development.

  Types of humidifiers

  According to the design, the principles of operation and the steam produced, there are 4 types of humidifier:

  • Cold steam appliances represent traditional appliances that are easy to make at home. Their main functionality is cold evaporation of liquid. Structures of this type can not only humidify the air, but also purify it. Air pollution in such structures accumulates on filters or cartridges. The advantages of such designs are quiet operation and no need for electricity consumption for steam generation.
  • Hot steam appliances allow you to humidify the air while heating the liquid. The simplest designs are hinged containers for the battery. The principle of operation of such devices is similar to that of electric kettle... This type of store unit is equipped with a hydrostat that helps users to control the level of moisture in the air.
  • A steam or ultrasonic humidifier is recommended for creating an optimal level of humidity in greenhouses, when growing crops and seedlings. The principle of operation of such a device is the evaporation of water using ultrasound. The dry air entering the humidifier tank exits as a cold mist. Constructions without heating the liquid are convenient to use in a room where there are small children.
  • Climatic complexes are multifunctional: humidification, purification from air pollution. The antibacterial and anti-allergenic filter of the steam appliance device helps to rid the room of unwanted odors and tobacco smoke. Constructions are convenient to use in offices and safely operate in a children's room.

  

  Rosemary Lemon Flavor

  An air humidifier is easy to make with your own hands, it can not only saturate the ambient air with moisture, but also aromatize it. It is quite simple to make it. For such a construction you will need:

  • capacity of 200 ml for water - 1 pc .;
  • clean water - 150 ml;
  • essential lemon oil - 15 drops;
  • essential rosemary oil - 5 drops;
  • vanilla extract - 5 drops.

  Manufacturing instruction:

  1. 1. Pour 150 ml of clean water into a container.
  2. 2. Add 15 drops of lemon oil and 5 drops of rosemary oil to the water, the same amount of vanilla extract.
  3. 3. Mix thoroughly.
  4. 4. Pour the resulting composition into a clean prepared container.
  5. 5. Place the container directly on or near the heating device, place it near the radiator.

  With a creative approach in choosing a beautiful container and filler, a humidifier will become an element of decorating a room or office. It is permissible to choose a glass vessel as a container, and use a hydrogel as a filler. The balls of this substance, getting into the liquid, increase in volume several times. Liquids and balls are selected in such an amount that, after increasing the size, at least half a centimeter remains to the edge of the container. Water is poured so that it completely covers the balls. As the liquid evaporates, the balls will dry out and decrease in volume, therefore, periodically add to the vessel clean water, but not more often than once a day.

  How to maintain normal humidity air in the apartment?

  Homemade spray

  A spray fragrance is most often purchased at a store. Self-made at home, the spray humidifier is much cheaper and more environmentally friendly, as it is made from natural materials. This version of the device will aromatize the room and will not harm the health of the household. To make it you will need:

  • clean water - 250 ml;
  • ethyl alcohol - 2 tablespoons;
  • one or a composition of essential oils of the consumer's choice (a good solution is lavender, eucalyptus, bergamot, neroli) - 20-30 drops;
  • a container with a built-in sprayer made of plastic or glass.

  Manufacturing technology:

  1. 1. A bottle of sufficient volume for spraying the premises is filled with water.
  2. 2. Add ethyl alcohol to the container in a ratio of 1: 3 in relation to the poured water.
  3. 3. There add essential oil or a mixture of them.
  4. 4. Thoroughly mix the composition.

  The container for the spray humidifier is ready. At first obvious benefits designs in ease of manufacture, natural ingredients, the method has an obvious drawback - it is the regular participation of a person in spraying the premises. The method is applicable in a residential apartment, but it is difficult to produce in an office or production area.

  Evaporation from the radiator

  Radiators are usually placed away from direct human access behind curtains, tables, screens or panels. Convenience of their hidden location in the room craftsmen used to create a natural humidifier. Wet matter hanging directly on the hot radiator, dries, evaporates moisture into the air space of the room, thereby moisturizing it.

  The advantage of the proposed methods for humidifying the air of a dwelling is the simplicity of the design and the absence of additional resources for the manufacture of the device. In terms of efficiency, folk humidifying devices are not inferior to store-bought ones.

  For the first version of such a humidifier, you will need sufficient space to place a container with water for evaporation near the radiator.

  
  

  Manufacturing technology:

  1. 1. Pure cotton fabric is matched to the color of the radiator.
  2. 2. Prepare a bucket or other container of a discreet color, which could be placed on the floor near the radiator. This is a plastic transparent bucket or food container.
  3. 3. The container is filled with clean water.
  4. 4. The cloth is moistened in it and hung on the battery so that the upper edge is hooked onto the radiator and the cloth hangs down without falling, and the other end sinks into a container with water.
  
  

  The second version of the radiator humidifier is hidden in the corner behind curtains and curtains. In this case, the container is placed on round tube suitable for the radiator. The construction technology is simple:

  1. 1. Prepare a plastic bottle for juice or carbonated drink, scotch tape, a piece of cotton cloth, which dries quickly, thereby humidifying the air.
  2. 2. A hole 4-5 cm wide and 10 cm long is made in the front panel of the bottle.
  3. 3. In the horizontal position, the plastic container is attached with tape to the radiator so that the hole is in the upper part.
  4. 4. Clean water is poured into the bottle through the cut-out hole so that at least 1.5 cm remains to the brim.
  5. 5. A strip at least two meters long and no more than three centimeters wide is cut out of cotton fabric. The strip is allowed not in one piece, but in fragments.
  6. 6. One end of the strip is lowered into the liquid of the container and the remaining part is sequentially wound onto the radiator. Strips are wound in both parts of the pipe from the container suspended from it. When several strips are applied to the pipes, hanging in the water, the effect of air humidification is enhanced.
  
  

  Homemade humidifier and design solution small ceramic vases suspended on a radiator can become an interior. For fastening the containers, it is recommended to use a wire that is threaded through the holes of the radiator accordion.

  The use of such air humidifiers does not require frequent human participation in the process. As the water poured into the container evaporates, it should be replenished.

  Construction with expanded clay filler

  Expanded clay is a material that perfectly absorbs liquid and therefore becomes the basis for a homemade humidifier. Construction based on this unique material Absorbs and releases moisture, being a 2-in-1 device. For manufacturing you will need:

  • mesh buckets - 4 pieces different sizes, 2 smaller, 2 larger;
  • a bucket with a capacity of 12 liters;
  • pump for an aquarium;
  • a cooler from a personal computer, the diameter of which is 14 cm;
  • construction hair dryer with high temperature heating;
  • plastic ties.
  

  Manufacturing algorithm:

  1. 1. At the first stage of manufacturing the structure, smaller buckets are glued together. This is done with a household hair dryer or plastic fasteners. The assembled structure is a humidifier body with an internal void. Large buckets are connected in the same way. Before the second connection is made, the first structure is placed in the second.
  2. 2. Before filling the space in the humidifier with expanded clay, it is necessary to cut off the top cover at the top container or make a hole into which it will be convenient to fill the elements of the substance. It should be noted to users that the fractions of expanded clay should be such that they do not spill into the openings of the mesh bucket.
  3. 3. Take a bucket with a capacity of 12 liters and place an aquarium pump on its bottom, the tubes of which are brought to the top of the structure from mesh buckets. A ring with plastic holes is installed on top of the entire structure.
  4. 4. At the top of the entire structure, a cooler is mounted, which will have to pump air into the expanded clay structure. Through the holes, moisture enters the air in the room.

  In the presented model of a dampening device, it is important to correctly choose the main ingredient - expanded clay - the very granules that should be of a suitable size. Before pouring it into the finished device, it is necessary to rinse the substrate under running water.

  Ultrasonic humidifier

  To create an ultrasonic device for humidifying the atmosphere of a living room with your own hands at home, you will need:

  • a steam generator operating on the ultrasound principle;
  • fan for a personal computer;
  • plastic container with a volume of 5 or 10 liters;
  • plastic disposable cup;
  • detail from a children's pyramid in the form of a donut;
  • 24v power supply;
  • corrugated flexible tube;
  • stabilizer;
  • construction corner made of aluminum.

  The listed items are always on hand or purchased at any hardware store. Estimated cost homemade unit is no more than one thousand rubles, which is significantly lower than an industrial humidifier.

  
  

  Manufacturing technology and assembly scheme is simple:

  1. 1. Use a drill to make holes in the container lid. They will be inserted into the fan mounts, outlet tube, steam generator wires.
  2. 2. The fan is then screwed onto the container and the corrugated tube is inserted. The listed structural elements are located at the opposing ends of the container.
  3. 3. A special floating platform must be constructed for the steam generating device. In it, the device will always float on the surface of the water, which will help ensure uninterrupted operation of the ultrasonic humidifier. To make a floating platform, you will need a plastic measuring cup and a round piece with a hole in the center, which is permissible to look at among the elements of the children's pyramid. Insert the glass into the bagel, drill a hole in the bottom of the glass, then attach a piece of tissue to it with an elastic band. The material then acts as a filtration. Then insert the steam generator into the beaker.

The Russian people are already very resourceful. What a person just does not come up with to save the family budget.One such invention ishomemade humidifier.

There are some easy waysmake a humidifierdo it yourself at home. Raising the humidity level in the room is very important. It is not necessary to use climatic technology, you can show a little ingenuity and do everything yourself.

From the bottle

You can make a similar device yourself from an ordinary plastic bottle.No need to buy anything, everything is at home.

This is the easiest method for humidifying indoor air during the cold season, when heating season and the heat dries it up.

So, the easiest and simplest way to make an air humidifier with your own hands:

1. Take a two-liter bottle of water or drink, also prepare scissors, a few pieces of thick cloth, tape and cheesecloth.
2. In a plastic bottle do 10 cm rectangular hole from the side. On the bottom with scissors cut through a small hole, 4 cm wide.
3. Use thick fabric for hanging the structure on the battery. Anchor a plastic bottle to the top of the heater that goes to the radiator.
4. Hang it horizontallyso that the hole on the side is up.
5. The fabric will slide off, so secure it with adhesive tape, superglue, or use tape.
6. Next, cut off the gauze with scissors. Width should turn out 10 cm, and the length is 1 meter. One end of the gauze is passed through the hole in the bottom, then, through a rectangular hole on the side output to the battery. Wrap her several times, again dip in water and secure on heater near the bottle cap.
7. Add water to the container and wait for the effect.

Thus, water will evaporate for a long time.A high degree of moisture cannot be achieved in this way.But this is the most budget-friendly option for a homemade air humidifier.

You can add to the water essential oils... Then the humidifier will also be a fragrance.

If the humidity in the room low , a plastic bottle won't save. In addition, you need to hang out wet things or make another homemade device that will work a little better and satisfy your needs.

A fan with a humidifier is also an economical option for efficient air conditioning.

It has many benefits, including:

• ease of use;
• the ability to transfer throughout the apartment;
• low energy consumption;
• can use not only as a humidifier, but also as an aroma lamp.

Humidify the air in the apartment not difficult if a man understands such technologies.

How to make a DIY air humidifier from a fan:

1. Wet dense material with water, wring it out so that the liquid does not drip onto the floor. Hang the fabric higher than the floor fan. Install the last one behind the material and turn it on. The fabric will have to be constantly wetted, which is not very convenient.
2. For the second option, you will need a cooler, old disks, a container with a capacity of 6 liters and plastic trims measuring 5 by 5 cm, glue gun, a motor from a children's toy and a gear. How to make a home humidifier: Plastic parts are needed to seal the holes on the discs, then they take a tube and put the discs on it, fix them together with a glue gun. Next, you need to make holes in the container, and insert a tube with discs into them. A gear is attached to one side, and the other is fixed with washers. It remains to install the electric motor from toys and connect with gear. The manufacture of a homemade air humidifier is completed by installing the cooler in the container lid and connecting to the network. The discs in the container are filled with water, but not completely.

That's all. If followcorrect sequencemaking homemade fan, everything will work out.

The second humidifier option is more effective.

From a plastic container

Necessary. The state of health of all living people in the house depends on this. This is especially important for allergy sufferers.

You can buy it, or you can do it yourself with the help of improvised means. The second option is more economical, nicer admire your own invention.

This way is more difficult than a plastic bottle humidifier, but also more effective.

Procedure:

1. Get a mesh drawer, which should be slightly smaller than a regular plastic one. Attach the fishing line to the top, pull it.
2. Hang the cut bandages on the fishing line. The gauze should reach the bottom and hang freely there.
3. Reticulate drawer setinto a large container that is filled with water.
4. Then in the lid of a large container cut through a fan-sized hole that is attached there with a glue gun or double-sided tape.
5. It remains to turn on the fan to the network.

This design is very quiet. The fan is spinning, thereby moisturizes air. Sometimes the water needs to be added.

This indoor humidification option efficient , and most importantly - economical.

Ultrasonic

Ultrasonic humidifiers are rightfully ranked first among similar devices.

They are safe to use, make little noise, have small compact dimensions, and are economical. Such devices have good performance, but are not cheap in stores.

The Russian person has a very inquisitive brain, he does not want to buy expensive equipment. It's easier to save money on it and do something like that. device on one's own.

For making homemade ultrasonic humidifier you will need the following tools:

• ultrasonic steam generator;
• cooler with power supply;
• plastic cup;
• Styrofoam;
• container;
• small diameter corrugated tube;
• voltage transformer;
• wires and plug.

A properly made humidifier will serve you faithfully for a long time. You will be able to use it for more than one year.

It can be used in winter and summer, that is, at any time of the year when the indoor air seems too dry.

Step-by-step instruction:

1. In a food container do 3 holes. Their shape and size must correspond to the size of the cooler, the branch pipe and the wires that will come out from the radiator.
2. Secure, outgoing corrugated tube. All docking areas lubricate with sealant.
3. Wait, until the sealant dries, keep assembling the device.
4. Next, make a float out of foam and a plastic cup. It is needed in order to ensure the smooth operation of the humidifier due to the steam generator. In foam do cup-sized hole and insert into it. On the bottom of the glass do too a small hole for water to flow. And to the very bottom with a glue gun attach a piece of gauze. This material will serve as a filter. An emitter is placed inside.
5. Connect emitter to voltage converter. All connections isolate.
6. Fill container with water. Put a float insideclose it tightly with a lid.

The work is over. You can use a homemade humidifier by plugging it in.

From expanded clay and buckets

Expanded clay is called a lightweight porous material that is made by firing clay or shale.

You will need trash bins to make a homemade humidifier. You must buy 2 large and 2 small, only they must be with holes.

You will also have to buy a large 12 L bucket,aquarium pump, cooler. It is necessary to rent a construction hair dryer, so as not to buy or use your own for hair.

Last thing , what is needed is plastic screeds.

So, how to create a homemade humidifier for an apartment:

1. Small baskets glue upper parts. It can be done, melting plastic with a construction hair dryer, use good construction glue or glue gun. This will be the body of the humidifier.
2. In the same way fasten large trash bins.Place a small bucket case inside... Then large containers glue.
3. Bottom by a large trash can cut off ... Use a utility knife or scissors. Into the resulting hole pour in expanded clay. That is, a void forms inside the small buckets.
4. Next take aquarium pump and place to the bottom of a 12 liter bucket. The tubes that come from her, output to the top of the mesh baskets, where a large hole was made for filling expanded clay.
5. Then as a cover install plastic ring.
6. To the very top of the structure attach cooler from the computer. It will direct the air currents into the expanded clay soaked in moisture.

A homemade humidifier is a real and doable task. Anyone who is really interested in it can do it. manufacturingat home.

The proposed manufacturing options will definitely come in handy. They can be used in the country, in a city apartment or in your own home.

Indoor air should always be comfortable for humans. Moreover, the principle of making homemade humidifiers is very simple.