Small droplets of condensation form on the pipes cold water and sewerage in apartments and private houses constantly. Most often, this process can be observed in summer period... Despite the fact that such a phenomenon is considered natural and quite natural, it causes many inconveniences to many. We are trying to come up with something, but still, seeing condensation on the pipes of cold water, we don’t know what to do. Why are these droplets so harmful?

It would seem that harmless condensation can create significant problems for the owners of an apartment or house:

• Accumulating and uniting, drops of water end up on the floor and form whole puddles there, which can even flow to neighbors below. Flooring from this it can suffer so much that after a couple of years it will have to be changed.
• Harmless drops also greatly reduce the operating period of the water supply system, because it is an aggressive medium for metal. Pipes rust, deform and after a while will require major repairs.
• Condensation on pipes in the toilet, kitchen or bathroom can cause bad smell dampness. But the smell is not that scary. It is much worse that the consequence of this is the formation of mold and mildew. Bacteria also multiply much more actively in a humid environment, exposing people living in an apartment to the risk of disease.

Causes of droplet formation

Why does condensation form on the pipes? Most often this occurs due to the temperature difference between the surface of the pipes and the air in the room. And if there is no ventilation in the room, or it does not function well enough, then nasty drops appear necessarily. Too humid indoor air also contributes to this. Moisture quickly settles on risers and pipes that carry cold liquid. Each room has its own reasons for condensation.

Wet pipes in the toilet

In the toilet, the most common causes of condensate deposition on pipes include:

Condensation in the bathroom

To know how to deal with condensation on pipes in the bathroom, you must first find out the cause of this phenomenon. Some factors are similar to "toilet" ones, but there are some nuances:

How to get rid of moisture on pipes?

There are several ways to remove condensate on pipes:

Ventilation

Inspect air vent... If you find debris, cobwebs and deposits of dust there, it is necessary to thoroughly clean it all. After that, it is advisable to purchase a special fan, which is installed instead of the ventilation grill. Plumbing and building materials stores have a ton of such devices from various manufacturers. They can vary in power, price and design.

New tank

In the toilet, the condensation problem can be solved with a double cistern. Inside such a device there is an additional plastic container into which cold water is drawn. The outer walls do not cool too sharply, therefore they are not covered with water droplets. Of the minuses - the high cost of the cistern, which is most often sold only as a set together with a toilet bowl.

Natural ventilation

If your bathroom or bathroom does not have supply and exhaust ventilation, organize life in your home so that everyone who takes a shower or a bath leaves the door wide open when leaving the bathroom.

Thermal insulation of pipes

How to get rid of condensation on cold water pipes by thickening the walls? To reduce the temperature difference between the air and the pipe, it is advisable to insulate the pipe. Several items can be found in stores modern heaters... They are characterized by high fire safety, high thermal insulation properties, ease of installation, tightness and a completely low price. Special cases made of foamed polyethylene - energoflex are very popular now. This material is very flexible, so there should be no problems with installation. And multiple closed pores will be very good at protecting against temperature "inconsistencies".

To put a pipe in an energy flex, you need to do the following:

• dry the pipe thoroughly, after wiping it with a dry cloth;
• the energyflex pipe must be cut lengthwise;
• starting from one edge, gradually put on the insulating material over the entire pipe with cold water;
• the longitudinal seam of the energy flex is fastened with clamps or glued with glue;
• if the pipe is long, then, using several pieces of insulation, you need to glue its ends together;
• thereafter, the insulating material, if desired, can be painted with paint from an aerosol can.

Another pipe and polyurethane foam

How to eliminate condensation on a cold water pipe using scrap materials? If for some reason you cannot buy this modern insulating material, then you can try using a plastic pipe with a little large diameter and polyurethane foam. The plastic pipe is also cut lengthwise and carefully slid over water pipe... Then foam is admitted into the annular space. This simple construction will last long enough, and will not interfere with the repair work.

Note: Instead of a plastic pipe, many use a metal corrugated pipe. You can also run polyurethane foam inside.

Rags

Another option is to use rags (bandages, any other cotton fabric) and epoxy putty. Before proceeding with the insulation of the pipe, it must be thoroughly cleaned of rust with sandpaper, and then degreased with acetone and treated with a rust converter. Only after that the first layer of putty is applied, which is immediately "bandaged" with a cloth. When this coating has hardened, another coat of epoxy must be applied.

Isollat ​​and other similar materials

When it comes to thermal insulation of cold water pipes, the universal insulating material Isollat ​​helps a lot. This is a thermos paint in the form of a water-based suspension. After drying, the liquid mass solidifies and turns into polymer coating with excellent thermal insulation characteristics.

It is very simple to paint a pipe with Isollat:

• clean well with a "sandpaper" and degrease the pipe surface;
• apply one coat of insulating material;
• wait until dry;
• use silicone varnish to finish and gloss the pipe.

Moisture absorbers

In large construction supermarkets you can find wonderful household appliances- moisture absorbers. They will help you quickly and without hassle to cope with the problem that has arisen. Their design is quite simple: an absorbent substance is placed in a plastic box. It will help not only eliminate condensation on the pipes, but also get rid of excessive moisture in the entire room.

Air conditioning

This is the most expensive option but some people use it too. Installing a climate controlled air conditioner will ensure a constant optimum humidity level.

What to do when the condensate of the water pipes keeps constantly on the pipes? When you see water droplets on the waterways of your apartment, do not ignore the problem in the hope that "it will somehow disappear by itself." Try one of the above methods, and the unpleasant consequences can be avoided.

When condensation forms on the cold water pipes, an experienced plumber will always tell you what to do. But there are times when it is not possible to seek professional help, so it is important to know why this phenomenon occurs and how to deal with it.

Reasons for the formation of condensation

Moisture can appear on both metal and plastic surfaces. The reasons for it are equally removable, regardless of So the accumulation of condensate contributes to:

• poor or no ventilation;
• stagnant water;
• faulty plumbing;
• temperature difference;

If condensation is found on the cold water pipes, what to do must be addressed immediately. An unresolved problem causes not only aesthetic ugliness, but also can damage the pipes.

Excess moisture can appear due to a sharp drop in temperature and excessive moisture... To eliminate the trouble, it is necessary to establish a ventilation system, and after taking a bath, leave the door open to ventilate the room.

In the toilet common reason The "crying" of pipes is the leakage of water in the cistern. The mechanism is simple: the water is constantly renewed and does not have time to warm up to room temperature... This keeps the chimney cold and the room warm. As a result, excess moisture appears.

Consequences of unrepaired condensation

In places where, as a rule, humidity is always high. But if the indicators go beyond the critical mark, then unpleasant consequences are possible for both pipes and living people.

• Mold and mildew growth. When condensation is on plastic pipes is constantly present, then droplets of water flow down the walls, fall on the floor. As a result, a favorable environment is formed for the development of pathogenic bacteria, which threatens the appearance of mold. In conditions of constant humidity, the fungus begins to multiply vigorously and it will be very difficult to get rid of it later.

• Property damage. Constant contact with water surely spoils all the things in the room. Metal pipes rust quickly, plastic ones lose their consumer properties. Ceramic tile may eventually fall off, and the paint and putty may crack.

To avoid this, you need to know how to remove condensate from cold water pipes and fix the problem in time.

Finding out the cause of the problem

Before you fight for water droplets on pipes, you need to figure out why they appear. To eliminate condensation on the cold water pipes, what to do in such cases is due to the reason for its appearance.

If it is a leak, then at night, when the movement of water stops, you can hear a quiet dripping. Therefore, it is worth finding a place for the flow of water, eliminating it and the problem with condensation will be solved by itself.

If moisture accumulates on the tank hose and parts of the system close to it, the problem is most likely in the tank system itself. Condensation forms due to the constant presence and relatively warm room. Therefore, it is necessary to establish a drainage system.

When all systems are working properly, the plumbing is in order, you need to check the ventilation. It is enough to put a sheet of paper on the vent and if it falls, immediately clean it. It often happens that this measure alone is sufficient to completely prevent the problem.

V summer time when it is hot in the room and cold water is passed through the pipes, condensation is an indispensable attribute. In this case, the elimination of too sharp temperature differences between the outside air and water in the pipes will help. Moisture-absorbing drugs may come to the rescue.

Problem in piping

When the cause of droplets on the pipes is a malfunction of plumbing or poor ventilation, then it is clear to any layman what to do. But what to do when the source is a technical reason. Often in apartments, hot and cold water pipes run too close to each other. In such conditions, it is clear why condensate on the pipes appears again and again, despite the good exhaust and serviceability of all systems.

If the wiring is in the public domain, you should definitely take care of thermal insulation. But in the case when the network is hidden, you will need the help of a specialist who will solve the layout geometry. In any case, cardinal repairs are required.

Thermal insulation material is used both special and made from scrap materials. Regular corrugation and polyurethane foam will do. In this case, the corrugation is cut to the required size and worn on problem areas. Where unfilled spaces remain, polyurethane foam helps out.

If plastic pipes "cry"

When the question is laid in the house, how to get rid of condensation is solved as follows:

1. It is desirable to replace conventional hood, built-in fan.
2. Carry out insulation measures using special tubes with an incision. They are easy to purchase at any plumbing or hardware store. These tubes are made of polyethylene, energoflex and effectively protect the tubes. the main condition for their use is careful preparation of the pipes so that they are completely dry.
3. In the case of a plastic trunk, you can radically solve the problem of "crying" if you treat them with a projector primer. After complete solidification, they can be painted. oil paint... This method is suitable if the room has an unrecoverable, constant and sharp temperature drop.

Please note that pipes for cold water are allowed to be coated with any enamel, and the hot water supply system is painted only with oil paint.

Getting rid of moisture on metal pipes

A problem with metal systems no less acute, because excessive moisture threatens the formation of corrosion and complete wear of the pipes. Therefore, if condensation appears on the cold water pipes, we will describe in detail what to do:

1. The pipes are cleaned from rust, dried completely and covered with oil paint.
2. All kinds of cracks in the floor and walls are treated with carbolate, a pasty substance. After it has completely solidified, it is also covered with oil paint.
3. The entire water main is treated with a projector primer, and then covered with enamel.

It should be remembered that the problem of condensation is often quite difficult to solve, so it is better to prevent its occurrence than to deal with the consequences later.

Experts who often come across crying trumpets have a lot of experience in preventing a problem in the bud.

Should be purchased at the Gofroterm plumbing store. The substance is applied to the entire surface of the pipes, as a result of which a strong and elastic base is formed, preventing the accumulation of moisture.

Good effect also brings liquid thermal insulation... It is applied to completely dry pipes and prevents sharp drops temperatures that cause condensation to form.

If there is a large difference between the temperature of the air and the supplied water, it is necessary to insulate the pipes. Most effective and suitable material for these purposes, it is sold in any hardware store at an affordable price. The material is fixed with a clamp and ordinary wire.

You can eliminate fogging using the proposed methods, but which method to choose must be decided after a precisely established reason.

Wet pipes in a private house

Condensation on pipes in a private house is mainly due to insufficient ventilation. Therefore, if the house is only under construction, you should immediately take care of a strong hood. Before installing the pipeline, you need to insulate it. This is especially worth paying attention to if the pipes for hot and cold water supply are located in the immediate vicinity.

An inadequate system is a common cause of condensation. Therefore, in order to avoid problems with this factor, it is worth paying attention to this.

For diagnostics, specialists are involved who, if necessary, will carry out cleaning. If the problem is not solved, you will have to install an additional exhaust duct. The ventilation system in a private house often allows you to do this without much damage and high costs.

Thermal insulation of pipes

It is better to insulate all pipes in the house. For these purposes, specialized materials are purchased. But you can use available tools and rid the house of constantly wet pipes.

A regular plastic tube is cut lengthwise and put on the problem area. The space between the pipes is filled with polyurethane foam.

It is easy to secure the metal pipe with an old rag. To do this, we get rid of rust, dry the pipe and wrap it with rags.

A rare person has not had to deal with such a phenomenon as condensation on the surface of a cold water pipeline. Although this unpleasant phenomenon can occur on other structures - windows, external walls, in the corners of rooms.

Condensation is caused by moisture vapor in the air. When they come into contact with a cold surface, they cool down and turn into drops. The higher the humidity in the room and the greater the temperature difference between the air and the cold surface, the greater the likelihood of this unpleasant phenomenon.

If the pipes and windows chronically "cry" in the house, then it is urgently necessary to deal with the causes of this phenomenon.

This mainly affects rooms such as bathrooms and toilets. This is where the risers of the cold and hot pipelines are usually located.

There are several reasons for water condensation on pipes:

• poor ventilation of the bathroom and toilet, leading to high humidity in them and an increase in the overall temperature in these rooms;
• in the toilet, the cause of the problem may be a malfunction of the valve that blocks the water in the toilet bowl - water leakage leads not only to its leakage, but also to constant cooling of the cold water pipe;
• in the bathroom, condensation often forms for the same reason - a malfunction of the mixer valve that shuts off cold water;
• high humidity in an apartment or house, which can be caused by many malfunctions - poor ventilation, leaking roof, incorrectly selected insulation.

If condensation has begun to form recently, then the cause must be found out immediately, and not wait for the problem to become chronic. Perhaps you recently changed windows or installed any equipment in the house that contributes to "warming the microclimate".

It must be remembered that although condensate is just water, it is it that is the main aggressive medium that destroys steel structures, including pipes.

In addition, excess moisture will sooner or later cause the appearance of mold and mildew not only on pipes, but also in any part of the apartment where there are cold surfaces.

And this is no longer just ugly, but often even dangerous for people living in the house, especially allergy sufferers.

How to deal with misted pipes

The algorithm is very simple - you need to find the cause and eliminate it:

• You can start by checking drain system tank and stopcocks. To do this, you will have to watch them. Sometimes people, leaving the bathroom, do not notice that the faucet is undermining, and the toilet valve periodically opens due to a decrease in the float level due to a small leak from the tank.
• Check that the ventilation is working properly with a piece of paper or by holding a lighted match up to the ventilation grill. If the piece of paper falls, and the match burns evenly, then the ventilation is not working.
• If you did not find any faults in your apartment, then you will have to visit the neighbors upstairs and find out from them if they have encountered the same problem. A malfunction on any floor located above leads to a constant circulation of cold water in the pipe, which significantly reduces its temperature.

• If in the bathroom and toilet you have forced ventilation, then it is worth checking the effectiveness of its work.
• If everything is in order, but the pipes "cry", then the reason for this is that the temperature difference between the pipe surface and the ambient air exceeds 17 degrees, and special methods will have to be used to solve the problem.

Solutions to the problem

The main idea of ​​all of the following methods is the thermal insulation of the cold water pipeline to reduce the intensity of exposure to too warm air.

• Pipe painting insulating paint... It is quite expensive, but at the same time effective method solving the task at hand. Here you should be patient, because to achieve the desired effect, you will have to paint the pipe at least 5-6 times. Each previous layer of paint must be dried well and only then the next one should be applied. In this case, the room will have to be forcibly ventilated - an ordinary fan is suitable for this.

• Insulation of the pipe with foamed heat insulator liners. The linings are soft pipes with a longitudinal cut. They are put on a dry pipe like a cover, and the edges are then glued together. To achieve the desired effect, it is very important that the size of the pad fits perfectly to the pipe diameter. if it is larger, then there will be no effect at all, and if it is smaller, then you will not be able to glue the edges of the lining. You can combine the two previous methods: first paint the pipe, dry the paint and put on overlays, which can also be painted on top with heat-insulating paint.
• Putting on a plastic pipe bigger size and filling the space with polyurethane foam, you can also achieve good results. But here it is important that the foam completely and evenly fills the space between the pipes, otherwise the method will not work.
• Self-creation of thermal insulation on the pipe surface. This is an inexpensive but troublesome method and a completely reliable solution to the problem.

To create it, you need to stock up on the following materials:

• epoxy putty;
• Plain cotton fabric (such as old sheets)
• strong thread or thin twine;
• putty knife;
• sandpaper;
• means for cleaning pipes from rust;
• acetone or other suitable substance for degreasing the pipe surface.

The fabric should be cut into strips approximately 10 cm wide and rolled up. Medical bandages of suitable width can also be used.

Then we proceed as follows:

• We clean the pipe from paint and thoroughly degrease its surface.
• Next, the pipe is treated with an anti-rust agent.
• After the pipe has dried, a layer of epoxy putty must be applied to it and immediately quickly wrapped with a cloth from bottom to top. In this case, the turns of the fabric should be superimposed on each other and impregnated with a putty. Then the fabric is secured with a thread.
• After the first layer has dried, several more are applied in the same way.
• At the end of the work, I again coat the pipe with putty on top.

Once the insulation is completely dry, it can be sanded and painted in a suitable color.

In solving the problem of "crying" pipes, the main thing is not to miss the moment before the pipes begin to corrode.

If you cannot fix the problem by eliminating leaks in the valves of plumbing fixtures and good ventilation, it is better to immediately resort to thermal insulation.

Condensation on pipes occurs due to the temperature difference between the ambient air and water in the pipe. This phenomenon can be seen especially often in the warm season. Excessive moisture on metal pipes leads to their rapid destruction, and on plastic pipes - to the formation of mold, so the cause of condensation must be eliminated in a timely manner.

Causes of condensation and remedies

Causes of moisture

If condensate accumulates on a cold water pipe, in order to figure out how to fix the problem, you need to identify the main causes of this phenomenon. There are several reasons for the accumulation of moisture on pipes:

• if condensate predominantly accumulates on the water supply pipes of the riser in the bathroom or sewage system, then the problem with the formation of a leak may be with the neighbors living on the floor above;
• poor ventilation in the room. The reason for the lack of air movement may be a clogged ventilation duct or metal-plastic windows, which, when closed, do not allow air to pass from the outside. With poor ventilation, water vapor accumulates in the living room, which subsequently settles on plastic pipes (metal pipes, and so on). You can check the presence of efficient ventilation with a match or a lighter. The flame from any object should be "drawn" into the hood. If this effect does not occur, then the channel is either clogged or unable to cope with its task.

Elimination of leaks

Why condensation forms on the pipes, they found out. Now let's figure out how to fix leaks.

First of all, it is required to determine the place where the water leakage occurs. The leak could be:

• due to faulty taps or mixer. In this situation, water will drip from the tap;
• after a pipe break;
• due to worn fittings on polypropylene pipes(metal-plastic pipes).

It is most difficult to detect pipe breaks or worn fittings if the pipes are hidden in the wall. To detect a leak, you will need to partially disassemble the box covering the pipes, or resort to the help of specialists who will identify the malfunction with special devices - thermal imagers. Both the one and the other methods will entail significant cash costs.

If a leak is detected in a mixer or tap, then you can:

1. change all gaskets. You can purchase a faucet repair kit at any specialist store. To select a repair kit, you need to know the brand and manufacturer of the mixer. You can replace the gaskets yourself;

1. if after the repair the formation of condensation on the pipes has not stopped, then the mixer must be replaced.

If a leak is detected in the pipes, then you can:

1. solder the pipe, that is, install the plug in the place of the leak. This method is considered the least reliable, therefore it is recommended to use it as a temporary measure.

Replacing the fittings is not a problem. It is enough to remove the leaking part and install a similar new product.

Before carrying out any operation, it is required to first shut off the water supply of the living quarters.

Troubleshooting ventilation problems

How to get rid of condensation on pipes if the reason lies in insufficient ventilation of the room? Required:

1. apply to management company with a request to survey and clean the ventilation shaft of the house. The specified work should be done free of charge and in a short time, since monitoring the technical condition of the house is the direct responsibility of managers;
2. what to do if the problems in the mine of the house are eliminated, but condensate still accumulates. Can be installed in bath, toilet, etc. additional fan integrated into the cooker hood. The fan can be turned on forcibly or work, for example, when the light is turned on;

1. get rid of condensation on cold pipe it is possible by installing an air conditioner or a cooker hood for the stove or.

Do-it-yourself thermal insulation of pipes

How to remove condensate from cold water pipes if all of the above faults are eliminated, but the problem remains? You can insulate pipes using:

• chemicals;
• specialized heaters.

Chemical insulation

For pipe insulation, you can use mixtures:

How to deal with condensation with chemicals:

1. first of all, it is required to clean the pipe surface from dirt and rust (if used metal pipes). Various chemicals can also be used to get rid of rust;
2. then the entire surface of the pipe is treated with a primer for the best adhesion of the insulating mixture to the pipe. The time for complete drying of the pipe is indicated on the packaging with the primer. On average, this takes 30 minutes - 1 hour;
3. a protective mixture is applied to the pipe surface. You can use a brush, roller or spray gun to get the job done. Usually, chemical preparation it is recommended to apply in 3-5 layers, and each layer requires preliminary drying, the time of which is indicated on the package;
4. to increase the durability of the pipes, it is recommended to apply a kind of fixer on top of the insulating material, which, in addition to its direct function, will give the pipes an aesthetic appearance.

More information about pipe processing with Teplomett mixture can be found in the video.

The use of liquid mixtures as a heat insulator allows not only to reliably protect pipes from condensation, but also to extend the service life of the water supply system.

Insulation with heaters

As insulating materials for pipes the following can be used:

• Styrofoam;
• basalt;
• foamed polyethylene;
• mineral wool.

As a rule, the material for pipe insulation is ready-made rolls, into which the pipe is inserted. The roll consists of:

To insulate pipes insulation materials, it is required:

1. prepare the surface of the pipe, after removing all dirt and rust from it;
2. if a glue-based insulation is used, then remove from inside protective film and wrap the pipe. If the insulation is not equipped adhesive base, then the entire pipe must be covered with special glue;

The diameter of the insulation roll must match the diameter of the pipe. Otherwise, it will not be possible to get rid of the condensation, since moisture will penetrate under the insulation.

1. press the material against the pipe for the best adhesion;
2. glue the hole through which the pipe was wrapped.

Condensation on pipes can destroy or sewage at home, as well as harm the health of people around, therefore, it is necessary to get rid of the accumulation of moisture on the pipes in a timely manner using any of the most effective and available methods.

Why does condensation appear on the cold water pipes, what should I do in this case? Condensation is a common problem, and it can appear on both metal and plastic pipes. At first glance, the problem is insignificant, but over time it causes a lot of trouble in the form of rust, mold and bad smell... That is, you still need to get rid of condensation. To do this, you need to find out the reasons for its appearance. Why do pipes sweat?

Why does condensation appear on cold water pipes

Most often, you can see condensation on the pipes in the toilet. One of the reasons is a water leak in the tank. The water is constantly changing and does not have time to warm up, hence the humidity. We get rid of the leak in the tank - this reason will disappear.

Sometimes from excessive moisture puddles appear near the riser. This means that the neighbors living above have a leak in the tank. At night, listen to the murmur of water in the sewer, and you will immediately understand everything.

Condensation also forms due to high humidity and temperature drops. To avoid condensation, you need good ventilation... To get started, just leave the toilet door open overnight, perhaps in the morning you will find a dry pipe.

The reason is obvious - the ventilation pipe is clogged. Unscrew the grate by ventilation duct and clean everything very well. Draft should appear in the ventilation duct.

In the event that there is ventilation, but it does not cope with the problem, you can install an exhaust fan. It attaches instead of a ventilation grill and you turn it on as needed.

The choice of fans in modern building supermarkets is huge, for every taste and for any price. Recently, the installation of such fans in toilets and bathrooms is very common.

How to fix the condensation problem

How to get rid of condensation on pipes in the bathroom? The pipes in the bathroom also sweat. The reason may be similar. Condensation on the riser - problems with plumbing from neighbors. The pipeline that supplies water to your plumbing gets wet - the tap is not working well. The lack of a hood, as in the first case, exacerbates the problem.
If systems with hot water and cold are very close to each other, fogging cannot be avoided.

It is necessary to make thermal insulation of the pipes, this is an excellent protection that will allow you to remove condensate.

Condensation often forms on the pipes in the bathroom due to a malfunctioning mixer. Leaking water helps to cool them. There is only one way out - crane repair!

How to get rid of condensation? Insulation for pipes will allow you to completely get rid of fogging of pipes. It is necessary to insulate the cold water pipes from interaction with external environment... There are special thermal insulation materials that you can use to get rid of condensation from pipes. You just need to buy such material and insulate the pipelines. The abundance of such materials on construction market the materials are very large.

If you prefer a budget option to eliminate moisture on the pipes, and do not plan to buy an expensive thermal insulation material, you can use other ways. You need to purchase a cylinder polyurethane foam and a plastic pipe or corrugation that is larger than the condensate pipe. The corrugation or pipe is cut into pieces so that they can be put on the problem pipe, then they are put on and the voids are filled with polyurethane foam.

There is another budget option for getting rid of condensate. You will need sandpaper to remove the rust and acetone to degrease the problem surface well afterwards. It is best to treat the pipeline with phosphoric acid and then apply a layer of epoxy putty to it so that it does not drip.

Then immediately wrap the pipeline with prepared strips of fabric so that the fabric is saturated with the putty. You can use an old sheet by cutting it into pieces that look like bandages. Putty and cloth will harden quickly.

You can do it several times in the same way. The work ends with the application of a finishing putty. It will look aesthetically pleasing if the putty is sanded and covered water-based paint the color you want.

In most cases, thermal insulation of pipes allows you to solve the problem of condensation, but sometimes the level of humidity in a house or apartment is so high that waterproofing of the floor and walls is necessary.