BRIEF REFERENCE

CLEAN WATER is water with a pleasant taste, containing no organic or non-organic organic matter in hazardous to health or undesirable concentrations, corresponding to the established sanitary standards and rules.

REVERSE OSMOSIS - water purification by passing it with pressure through a semi-permeable membrane. This is the principle behind atoll RO filters and does not involve the use of chemicals.

MEMBRANE is a semi-permeable material through which only water and oxygen molecules can pass.

PREFILTERS - are used to purify water from insoluble particles, chlorine, organic substances before the water reaches the membrane, and help to increase the life of the membrane.

CONTENTS OF DELIVERY

Your new atoll RO filter has been thoroughly tested at the factory for leaks, the quality of the treated water and the functioning of all components.

When developing the filter, it was assumed that it should be placed under kitchen sink... This is its recommended installation location.

Before you start installing the filter, please read the entire Manual carefully.

The filter delivery set includes:

• filtration unit (1);
• storage tank for storing purified water (2);
• accessories: clean water tap (3), combined water supply unit (or water supply tap (4) and tee (5)), tank ball valve (6), drain clamp (7);
• four colored tubes connected to the filter (black, blue, red, yellow) 1.2 m each (8);
• set of cartridges (9) Cartridges can be sold assembled with the system or be included in the delivery set;
• wrench for unscrewing the prefilter housings (10);
• blue brackets to prevent accidental disconnection (not all connections may be installed, their absence does not interfere with the safe operation of the system);
• FUM tape;
• Silicone Grease
• User manual.

SAFETY INFORMATION

The atoll reverse osmosis filter fully meets all safety requirements, which is confirmed by the Russian certificate of conformity. Nevertheless, everyone who uses it should know the principle of operation and its features. safe work... To avoid problems and errors, carefully read this section and strictly follow the instructions for installing and maintaining the filter.

Important! The pressure at the filter inlet should not exceed 6 atm. If there is a possibility of increasing the pressure in the inlet pipeline above 6 atm, in order to prevent leaks, it is recommended to install a Honeywell D04 or D06 pressure reducing valve in the system before the first prefilter.

• The filter is designed to purify water in the amount necessary for cooking, drinking and other household needs.
• Check the water to be purified for compliance with the points “Requirements for water supplied to the filter”.
• If the filter is brand new, do not use purified drinking water until the completion of the adjustment and flushing procedures.
• Adjustment and flushing of the filter is carried out in the following cases:
• at the first connection;
• when replacing the filter in a place with a different quality of source water;
• after replacing the membrane and / or replacement elements.
• If the supplied water is of unknown quality, then after the filter starts operating, it is advisable to analyze the purified water. In the future, to make sure that the filter is working properly, the purified water should be checked at least once a year, or if its taste changes. If the analysis results are unsatisfactory, contact the service organization.
• In the event of water leakage or other malfunctions, stop the water supply to the filter and call a specialist to restore normal operation.
• Important! If it is possible that the temperature in the room where the filter is installed below 0 ° C, it is necessary to protect the filter from the effects of low temperatures. If this condition is not met, you cannot count on warranty service.
• Modifications to the system or making any design changes are prohibited. This could result in personal injury and / or property damage. Wherein warranty obligations also lose their force.
• Everything necessary work with plumbing must be carried out by a qualified technician. If you make the connection yourself, then you need to familiarize yourself with current regulations and stick with them.
• When moving the filter for storage for more than 2 weeks, you must:
• disconnect the filter from the water supply, turn off the power supply;
• empty the storage tank;
• remove the membrane and replaceable elements, pack in a bag and place in the refrigerator (+2 - + 5 ° C).
• Replacement parts should not be stored near odorous or toxic substances and must be protected from dust.
• Do not keep purified water in aluminum or copper containers due to possible corrosion and a possible increase in the concentration of non-ferrous metal ions in clean water.
• Do not place objects on top of the filter and storage tank.

Check the system regularly for leaks.

To limit damage from water leakage, it is recommended to install an atoll anti-leak valve. Leak Stop® on the tube through which water is supplied to the filter.

The service life of the atoll reverse osmosis filter is 5 years.

Although the atoll reverse osmosis filter retains all bacteria and viruses contained in the source water, it is recommended to use the filter only with microbiologically safe water. Use a filter to purify water that has been pre-disinfected with chlorination or UV light. V otherwise the service life of prefilters may be less than the period of their regular replacement.

ATTENTION!

To prevent bacteria from entering the filter during installation, we recommend that you wash your hands thoroughly with soap and water or use new clean rubber gloves before connecting all pipes and installing the membrane and cartridges, as well as before installing the water supply unit and the storage tank tap.

* - the useful volume of the storage tank depends on the pressure in the water supply system and is usually 50-70% of the total volume.

A typical water treatment scheme is shown in rice. 3... All elements are replaceable, and you can always choose the most optimal option for your conditions.

For reliable and long-term operation of the atoll reverse osmosis system, it is recommended to use the following devices of the given diagram in order of decreasing importance:

1. Stage - 2 - pressure reducing valves with a preset pressure in the range of 3-4.5 bar to protect against pressure surges in the water supply.
2. Stage - 1 - filter pre-cleaning- on highly polluted water.

The rest of the steps are optional and serve to protect other plumbing devices. See the Commentary Table for details.

All equipment is built into the water supply system, but its further maintenance (cleaning, replacement of cartridges) and repairs are carried out right on the spot - without dismantling from the water supply network.

Filter drinking water installed in the kitchen in the cabinet under the sink.

Due to the high performance of the circuit elements, their installation does not affect the water flow rate in any way.

All devices, with the exception of drinking water filters, are capable of functioning in a wide temperature range: for cold water- up to + 40 ° С, for hot - up to + 80 ° С.

Parameters \ Stages	1st	2nd	3rd	4th	5th	6th
Appointment	Preliminary mechanical cleaning 100 microns (500-20 microns)	Reducing pressure, protection against water hammer	Fine mechanical cleaning (20-1 microns)	Chlorine removal, bad smell and chromaticity	Protection against limescale deposits	Drinking water treatment
Equipment	Honeywell FF06 / F76S	Honeywell D04 / D06F	I-11S / I-11SH	I-11Bc / I-12Bc / I-11BHc / I-12BHc	I-11Ss	A-450 / A-550 / A-575
Principle of operation	Strainer	-	Polypropylene mechanical filter	Sorption on granular carbon; additional mechanical cleaning	Binding of hardness salts with hexametaphosphate	Reverse osmosis
Productivity (l / min)	70 / 200	-	20	up to 60	20	120l / day / 120l / day / 195l / day
Replacement terms	Depending on water quality / not limited	-	6 months	6 months	6 months	Prefilters and postfilters - 6 months, membrane - 24-30 months.
Operating conditions: P, atm, T, deg. Celsius	P = 1.5-16 (cold), 1.5-25 (hot) T - up to +40 (cold), up to +80 (hot) / up to +40 (cold), up to +70 (mountains)	R	R	R	R	P = 2.8-8.4; T - up to +40; cold water only
Installation	To the technical cabinet	To the technical cabinet	To the technical cabinet	In front of a bath or shower	Front household appliances with heater for cold water	Under the sink, with a separate drinking tap

PRESSURE PUMP CONNECTION DIAGRAM FOR SYSTEMS A-550 p, A-575 p

Indexes in the designation of models

“M” - used as a postfilter carbon cartridge with mineral additives;

“P” - the system is equipped with a pressure boosting pump.

When installing outside centralized drinking water supply systems, it is recommended to pre-analyze the source water. If the water characteristics established as a result of the analysis are worse than those indicated above, it is advisable to install an additional water treatment system. It is better to consult with the specialists of the seller or service center about its composition.

I. CONNECTING FLEXIBLE TUBES WITH QUICK DISCONNECTORS

ATTENTION: tubes can be cut for ease of installation, but we recommend keeping their length to facilitate service... No tools are required to connect the four colored tubing. The pipes must be cut straight, otherwise leaks at the joints are possible.

JOIN IS VERY EASY!

1. Cut the tube at right angles.
2. Insert it into the connector until it stops. Apply additional force to seal the joint. In this case, the tube will be drowned by about 3 mm and will be tightly crimped with the rubber ring of the connector.

PIPE CLOSED

Pull the tubes to check the connection.

To prevent accidental disconnection, secure the ring with the blue clip ( rice. 6).

DISCONNECTING IS EASY

1. Make sure there is no pressure in the tube.
2. Remove the blue clip to prevent accidental disconnection.
3. Click on the ring at the bottom.
4. Pull out the tube while holding the ring down.

Please pay attention to the need to check the tightness of the connection before installing the filters. During this check, it is necessary to pull the tubes coming out of the connectors with sharp movements. This will check the reliability of the connection and ensure the notch of the tube with the metal hooks of the connector.

The tubing should be cut straight, at right angles.

II. DRILLING A HOLE FOR A PURE WATER TAP AND CONNECTING IT TO A FILTER

ATTENTION: although the process of drilling a hole in the sink is not very difficult, it nevertheless requires appropriate skills, attention and care. Use protective goggles and gloves. Contact a specialist if necessary.

To install a clean water tap (A), a flat surface of sufficient rigidity is required so that the tap is securely anchored in an upright position. When choosing a location for drilling a hole (diameter 13 mm), be guided by aesthetic considerations, after making sure that:

• the length of the blue tube is enough to connect a clean water tap to the filtration unit;
• on the underside of the countertop or sink, nothing will interfere with the connection of the tube to the fresh water tap.

Install the clean water tap in accordance with rice. eight... We recommend not to tighten the nut (see. rice. eight) before the installation is completed and the system is functional, so that it is possible to make sure that there is no water leakage at the junction of the valve body and the threaded tube. A set of parts for connecting to a tube can be supplied with a clean water tap, or a clean water tap may include a quick-disconnect connector. On rice. 9a, b, c are given possible ways connecting the blue tube to a clean water tap. If there is no place on the surface of the sink for installing a tap, then it can be mounted on the surface of the table ( rice. ten).

III. COLD WATER CONNECTION

ATTENTION: make sure that the filter is connected to cold water (tmax 38 ° C). Connect to hot water will disable the filter.

Close the cold water shut-off valve. Open a cold water tap on the mixer to relieve pressure. If water continues to flow from the tap even after the valve is closed, you will have to close the main valve of the house or apartment. The system is connected to the water supply through the water supply unit. The filter kit may include a combined water supply unit, a tee tap. In this case, go to step 6 Assemble the water supply unit by connecting ball valve with a tee as shown in rice. eleven... Using the FUM tape, screw the water tap into the tee. Be extremely careful when connecting the valve - excessive force will damage its threads. Use only a wrench or small adjustable wrench. Do not use other materials to seal the connection. Loosen the union nut and disconnect the flexible hose from the mixer. Replace the union nut gasket if necessary. Install the assembly into the gap in the mixer wand as shown in rice. 12... Use a wrench or adjustable wrench. Connect the red tube from the filter to the ball valve using a union nut or quick disconnect.

IV. INSTALLING THE TANK BALL VALVE

Note: do not touch the air valve on the storage tank (located on the bottom of the tank). A yellow tube is used to fill and empty the tank; depending on the operating mode, the direction of the water flow changes in it. Wrap the threads on the top of the tank three times with FUM tape. Connect the tank ball valve to the top of the storage tank (see. rice. 13). To avoid damage to the valve, do not use excessive force when installing it. Use a wrench or adjustable wrench. Connect the yellow tube from the filter to the quick connector on the ball valve of the storage tank using a union nut or quick connector.

V. DRAIN CLAMP INSTALLATION

The drain clamp fits the drain siphons of sinks with a diameter of 40 mm. It must be installed on the vertical part of the pipe before the first bend of the siphon ( rice. 13). The section of the pipe into which the drain tube comes out must not be filled with water. Drill a 6.5 mm hole where you plan to install the drain clamp. Stick the seal on inner side drain clamp brackets with connection. Insert the tube into the clamp bracket ( rice. 15). Position the two drain clamp brackets so that the hole drilled in the siphon lines up with the hole in the drain clamp and the protruding part of the tube. Tighten the mounting bolts. They should be tightened evenly so that the two drain clamp brackets are parallel to each other.

The filter can be completed with a drain clamp with a union nut.

Vi. RINSING THE FILTER AND STARTING OPERATION

DO NOT DRINK THE WATER THAT HAS BEEN OBTAINED FROM TWO FIRST TANK FILLINGS!

1. Install prefilter (s). The first prefilter (marking on the PREFILTER flask) is already installed in all models. Install the carbon cartridge into the second flask (CARBON marking). Install a mechanical pre-filter in the third stage (SEDIMENT). To install the cartridge, it is necessary to unscrew the flask using a wrench (10). Peel off carefully protective film from the cartridge and install it into the flask. Pay attention to the “THIS END NEXT TO VESSEL THREADS“ mark on the top cap of the cartridge or the directions on the label. Tighten the flask by hand, without using a wrench, without applying excessive force.
2. Install the membrane. To do this, disconnect tubing (H) from the diaphragm cap quick connector. Unscrew the cap of the membrane flask (MEMBRANE marking). Lubricate silicone grease rubber membrane seals. Install the diaphragm into the body according to rice. 16... Lubricate the diaphragm flask cap seal with silicone grease and carefully install it onto the flask. Screw on the diaphragm flask cap and attach tubing (H). Make sure that the flask cap O-ring is installed on the flask without distortion.
3. Disconnect tubing (F) from the inlet of the shut-off valve and direct it into any container (bucket, sink, etc.).
4. Open for 2-3 minutes. water supply valve (B) for flushing the cartridges.
5. Close the water supply valve (B), attach the tube (F).
6. Close the tank cock (C).
7. Open the water tap (B). Switch on the power supply if a pump is present in the system.
8. Make sure there are no leaks.
9. After five minutes, water will start dripping from the fresh water tap (A). Let the water drip for 10 minutes, after which, after a few minutes, no more water flows into the drain from the black tube. The system has now reached the maximum possible clean water pressure. Pull on the tubes again to check the connection.
10. Open the tank valve (C) by turning it 90 ° - the process of filling the tank will begin. This will take several hours depending on the inlet water pressure.
11. After filling the tank (you will hear that water is no longer flowing to the drain and the pump (if present) is not working) open the clean water tap (A) and wait until all the water has flowed out.
12. Close the fresh water tap (A). Let the tank fill a second time. This process will take about 2 hours. Then drain the water from the tank.
13. The clean water from the third filling of the tank can be used.
14. Important! Check the system daily for leaks during the first week of operation.
15. When the system is first started up, the color of the water may be slightly milky. Don't worry - these are small air bubbles, they will disappear soon. The normal process of displacing air from the system is in progress.
16. Make sure there is no leakage at the bottom of the pure water tap body, tighten the tap nut ( rice. eight).

Vii. REPLACEMENT PROCEDURE

(cm. rice. 4)

* - the actual terms of replacement of replaceable elements can differ significantly from the recommended ones due to the poor quality of the water supplied to the filter.

If it is necessary to replace worn-out cartridges, it is recommended to purchase special sets of replacement elements.

Replacing prefilters

1. Open the fresh water tap (A) to relieve pressure.
2. Using the key (10), unscrew the prefilter flasks, for this, hold the system with one hand, and turn the key with the other.
3. Remove and dispose of used replacement parts. It is recommended to protect your hands by wearing rubber gloves to avoid touching used parts. Replaceable elements, as well as the filter itself (at the end of its service life), must be disposed of together with solid household waste.

   Remember the sequence of installing replaceable elements. Rinse inner surface flasks for household detergent and brush and rinse thoroughly with clean water.

4. Remove the o-rings of the flasks, wipe them dry. It is advisable to lubricate the gasket of the new replaceable element, as well as the O-rings of the prefilter flasks with silicone grease or vaseline oil.
5. Place the new replacement elements in the filter flasks in the same order as the old ones were installed (after removing from the new cartridges plastic wrap), and screw them to the system until they stop. The flask must be screwed on by hand; a plastic wrench can be used only in case of EXTREME NECESSITY.
6. Disconnect the white tubing (F) from the inlet of the shut-off (four-way) valve.
7. Place a bucket or sink under the pipe and turn on the water tap (B). In this case, the newly installed replaceable elements will be flushed.
8. After 2-3 minutes, close the water tap (B) and connect the pipe (F) to the shut-off valve.
9. Close the fresh water tap (A).
10. Open the water tap (B). Switch on the power supply.
11. Check the system for leaks.

Replacing the membrane

Pay attention to the tightness of the quick couplings when replacing the diaphragm. If, after several connections (for example, to replace cartridges), the edge of the tube has numerous “seizures”, it should be cut off.

1. Close the water tap (B). Disconnect the power supply.
2. Close the storage tank valve by turning it 90 degrees.
3. Open the fresh water tap (A).
4. Disconnect the tube (H) from the cap of the membrane flask (MEMBRANE mark on the flask).
5. Unscrew the cap of the membrane flask, remove the used membrane. Remember the direction of installation of the membrane in the flask, discard the old membrane. The used membrane must be disposed of with solid household waste.
6. Install a new membrane (see item 2 of the section "Flushing the filter and starting operation").
7. Close the fresh water tap (A).
8. Open the storage tank valve (C).
9. Open the water supply valve (B) to the system. Switch on the power supply.
10. 10. Check the system for leaks.

Replacing the carbon post-filter

Pay attention to the tightness of the quick couplings when replacing the post-filter. If, after several connections (for example, to replace cartridges), the edge of the tube has numerous “seizures”, it should be cut off.

1. Close the water tap (B). Disconnect the power supply if a pump is present in the system.
2. Close the storage tank valve by turning it 90 degrees.
3. Open the fresh water tap (A).
4. Detach two tubes from the post-filter (POSTFILTER marking on the flask).
5. While holding the filter, remove the post-filter from the clips holding it.
6. Reinstall the new postfilter in place of the removed one. In doing so, do not confuse the inlet and outlet (the direction of water flow is indicated on the body).
7. Attach the tubing to the quick disconnect connectors.
8. Open the system water supply valve (B) and clean water supply valve (A). Switch on the power supply. Let the water drain for about 10-15 minutes.
9. Close the fresh water tap (A).
10. Open the storage tank valve (C).

After any replacement of replaceable elements, it is necessary to flush the entire system. To do this, you need to drain one tank of water, which will fill up in 1.5 - 2 hours.

Before attaching the tubing to the quick couplings, it is advisable to lubricate the ends of the tubing with silicone grease or petroleum jelly to better seal the connection.

Unevenly cut tubing can cause leaks in the system. If necessary, correct the cut so that the cut angle is 90 °.

Dependence of the volume of obtained pure water on the water pressure at the filter inlet (water temperature 15 ° C, product withdrawal 15%)

POSSIBLE FAULTS AND THEIR ELIMINATION

Problem	Cause	Elimination
Leaks	Threaded connections are not tightened	Check and tighten the screw connections if necessary
	The pipes are not tightly connected	Remove and reconnect the tube
	Missing o-rings	Contact supplier
Increased noise	Clogged drain	Find and remove the blockage
	High inlet pressure	Install a pressure reducing valve. Adjust the pressure with the water tap
Milky water	Air in the system	Air in the system is a normal event in the early days of the system. After one to two weeks, it will be completely withdrawn.
Low productivity	Low water pressure at the inlet to the filter
	The tubes are bent	Check tubing and remove kinks
	Clogged prefilters	Replace prefilters
	Diaphragm clogged	Replace the membrane
	Low water temperature	-
Water has bad smell or smack	The resource of the carbon post-filter has run out	Replace the carbon post-filter
	Diaphragm clogged	Replace the membrane
	Canned food is not washed out of the tank	Empty the tank and refill (the procedure can be repeated several times)
	Incorrect tubing connection	Check the connection order
	The system has just started working	The tank is filled within 1.5-2 hours. Low temperatures and inlet pressure reduce the performance of the membrane. Maybe you just have to wait
	Clogged prefilters	Replace prefilters
	Air pressure in the tank is high	Check the pressure in the empty storage tank through the air valve using a pressure gauge. Normal pressure is 0.4-0.5 atm. If there is insufficient pressure, pump with a car or bicycle pump
		Replace flow restrictor
	Clogged check valve in a flask membrane	The check valve is mounted on the membrane flask inside a central connector located on the side opposite the flask cap. Unscrew the connector, rinse the valve under running water
Water does not flow from the tank to the tap	The pressure in the tank is below the permissible	Pump air through the tank air valve to required pressure(0.5 atm.) Car or bicycle pump
	Tank membrane rupture	Replace tank
	The tap on the tank is closed	Open the tap on the tank
There is no water in the drain	Water flow restrictor to drain clogged	Replace flow restrictor
Water flows into the drainage constantly	Defective shut-off valve	Check the shut-off valve. For this: close the tap on the storage tank; open the tap of clean water; you hear water pouring out of the drain pipe; close the tap of clean water; after a few minutes, the flow of water from the drainage tube should stop; if the flow does not stop, replace the shut-off valve This system requires an inlet pressure of at least 2.8 bar. If the pressure is lower than the specified, then a booster pump should be installed (see the "Options" section)
	The pump does not turn off	There is not enough water in the tank	See above
Sensor adjustment required high pressure		If water does not flow into the drain and the pump does not turn off, turn counterclockwise the adjusting hex on the high pressure sensor

DISINFECTION OF THE FILTER

Disinfection of reverse osmosis systems is carried out after a long (more than 3 weeks) system downtime. Disinfection is also desirable when replacing cartridges. Use unflavored 5.25% household chlorine bleach(sodium hypochlorite). Distinguish between disinfection of the filtration unit and disinfection of the storage tank.

Sequence of actions for disinfection of the filtration unit

1. Turn off the water supply.
2. Turn off the tap on the tank.
3. Remove and discard all cartridges and post-filter.
4. Remove the membrane, pack it in an airtight bag and place in the refrigerator.
5. Screw the flasks of the 2nd and 3rd prefilters, the membrane flask, connect the tube from the pure water tap to the tee instead of the postfilter.
6. Pour 50 ml of bleach into the flask of the 1st prefilter. Screw on the flask.
7. Open a fresh water tap.
8. Restart the water supply to the system.
9. When water with a chlorine smell comes out of the fresh water tap, close it and turn off the water supply to the system again.
10. Leave the system on for 2-3 hours.
11. Open a fresh water tap and resume water supply to the system. Wait for the chlorine odor in the tap water to disappear.
12. Install new cartridges into the system. Install the membrane. Open the storage tank tap. Restore the water supply.

Sequence of actions for disinfection of the storage tank

1. Turn off the water supply.
2. Open a fresh water tap and drain all the water.
3. Turn off the tap on the tank.
4. Remove prefilter cartridges 1-3.
5. Screw the flasks of the 2nd and 3rd prefilters.
6. Disconnect the tubing to the storage tank from the post-filter tee and connect it to the outlet of the 3rd prefilter instead of the tubing to the shut-off valve.
7. Pour about 10 ml of bleach into the flask of the 1st prefilter. Screw on the flask.
8. Open the tap on the tank.
9. Restart the water supply to the system for 5 minutes.
10. Close the tap on the tank and leave it filled with solution for 1-2 hours.
11. Drain the tank by disconnecting its tube from the outlet of the 3rd prefilter. Re-establish the original tubing connections.
12. Install cartridges into the system. Open the tap on the tank. Restore the water supply.

Options

1. Increasing the system performance, upgrading the system to operate at low water pressure in the supply pipeline (for models not equipped with a pressure boosting pump).

If the water pressure at the filter inlet does not exceed 2.8 atm., Then to increase the capacity, it is advisable to install a pressure boosting pump ( rice. 17). If there is a possibility of increasing the pressure in the inlet pipeline above 4 atm., In order to prevent leaks, it is recommended to install a Honeywell D04 or D06F pressure reducing valve in front of the pump.

The pump is installed in front of the first prefilter in the rupture of the red supply tube. For normal operation of the pump, it is necessary to fix it on a vertical or horizontal surface with four screws.

* If the input water is of very poor quality and contains a large number of mechanical impurities, it is necessary for the normal operation of the pump to install an additional main pre-filter atoll I-11S.

The pump should only be installed complete with a high pressure sensor installed in the tube break in front of the storage tank. The sensor is necessary so that the pump works only when filling the storage tank. After the tank is full, the water flow is stopped and the pump is turned off. Sensor low pressure prevents "dry running" of the pump. The sensor is mounted in front of the first prefilter. Both the high pressure pump and the sensors are equipped with quick connectors.
2. Elimination of microbiological contamination of the input water. The presence of microorganisms leads to fouling of prefilters, a drop in pressure and, accordingly, to a halt in the operation of the filter as a whole. To avoid this, it is recommended to pre-install ultraviolet lamp Sterilight SC1 / 2 (see. rice. eighteen) complete with atoll I-11S main prefilter.
3. Protection of the storage tank from unwanted ingress of microorganisms. If the filter is not used for a long time (2-3 weeks), there is a possibility of the penetration of microorganisms through the tap of clean water into the storage tank. It is possible to clean the tank from microorganisms that have got there only by subsequent flushing with a disinfectant solution. To prevent this, it is necessary to install a Sterilight SC1 / 2 ultraviolet lamp between the clean water tap and the storage tank in the break of the blue tube (see. rice. 19). The lamp is attached to the filtration unit or to any surface using two clips.
4. Connection to the ice maker. The ice maker is connected to the filter through a tee (for example, UT0404), installed in the break of the blue tube from the filtration unit to the tap ( rice. twenty). The length of the tube from the filter to the ice maker should not exceed 10 meters.

5. Reducing the content of nitrates in the source water.

For the most effective removal nitrates, you must additionally install a filter containing a replaceable element atoll NRC-10. The decision on the place of installation of the nitrate prefilter should be coordinated with the specialists of the seller or service center.

If you require replacement of Atoll filters, contact the Yuda contractors. On the Yuda website, you will find craftsmen in Moscow who can change cartridges at affordable prices.

Yudu specialists carry out the installation of replaceable filter parts for various models. For example, a master can quickly change cartridges in the Atoll A-550 filter. The service life of Atoll filters largely depends on:

• moisture hardness
• total consumption
• crane operation

If in your house or apartment the taps carry out almost uninterrupted operation, the filter elements will need to be changed much more often than indicated in the recommendations. Performer Yuda will tell you about these and other nuances during your arrival.

Despite the fact that A-550 replaceable elements have a resource reserve, the replacement of filters should be carried out based on normative indicators... Our specialists comply with all technical standards and safety rules. Therefore, all work will be performed as efficiently as possible.

In cooperation with qualified specialists, you can be sure that original filters from the Atoll manufacturer will be installed in your house or apartment.

The masters who are replacing the Atoll filter will install you those replacement elements that:

• will meet all sanitary standards
• have the appropriate certificates
• made of quality materials

At the end of the installation, the filtration of drinking water will be carried out as efficiently as possible. Professional Yudu performers will always select the right model for your cleaning system.

Selection of parts by numbers

Before starting work, experts will advise you to stop at optimal options- new sets of filter elements, which have unique numbers from 101 to the variant with the number 5. You can entrust the contractor Yuda to purchase them at an affordable cost.

By choosing the most suitable replacement elements from this series, you can be sure of the quality of water purification. Models from the 101-106 series (from 1 to 5) save you from the need for additional selection of missing filter elements.

Specialists carry out the choice of Atoll filters free of charge. You pay only for their immediate cost. Performers Yuda will be able to choose an option for you that suits the price and their technical specifications... You shouldn't contact various companies offering this service. They are often brokers, so the cost of replacing mechanical filters would be overpriced.

The service provided by qualified Yudu craftsmen will be provided at affordable prices. You will be able to agree with the contractor all the nuances of the upcoming work.

Before changing the cartridges in the Atoll filter, performer Yudu will make sure that all necessary tools for the cleaning. You can get clean water with smooth operation system and availability of all components, including:

• drain clamp
• key to scroll through prefilters
• storage tank
• FUM tape

For installation household appliances Yudu specialists are used special drill and keys. After choosing a new model and replacing the mechanical filters, further operation is possible.

To obtain clean moisture and smooth functioning of the new filter element, the pressure should be no more than 2.5 atmospheres. The contractor of your choice will check this value and will comply with all the necessary standards when working with a system of flowing drinking filter elements. The change of Atoll filters, carried out by our performers, will be as efficient and high-quality as possible.

Benefits of cooperation

On the Yuda website, you will always find professional performers who install household appliances. You shouldn't contact different companies, because they provide a surcharge for the service provided. The Yudu performers collaborate directly. With their help, the replacement of Atoll filters is carried out in any districts of Moscow.

You can discuss all the details of the work personally with a specialist. Atoll filters will be replaced in the shortest possible time, in compliance with all the requirements for its uninterrupted operation.

If you are using a cleaning system atoll, replacing cartridges should be done every six months. Are you sure of own forces? Can you do all the work yourself? Then heed our recommendations!

Instructions for replacing cartridges.

The cleaning system works at full capacity only when it is handled correctly and the filter elements are changed on time. Otherwise, there can be no talk of any clean and useful water. And remember that only original cartridges remove all dangerous impurities from the water.

If you have already purchased atoll filters, replacement of cartridges is carried out according to the following scheme:

• We turn off the tap of the general water supply to the apartment, as well as on the system itself and the storage tank.
• We open the drinking tap so that all the liquid remaining in the system comes out.
• We take out the filter from the cabinet, and then unscrew the flasks with a special key.
• We take out the old cartridges and rinse all containers well, then wipe them dry.
• We install new filters, tighten the flasks.
• We put the system in place and turn on the water to check for leaks.

Experts recommend opening the tap for drinking water supply for 5 minutes after replacing the cartridges. The liquid will completely fill all the flasks, and the filter elements will be able to start their work - high-quality water purification from all contaminants hazardous to health.

How often do you need to change cartridges?

If your house has atollfilter, replacement consumables must be timely. The manufacturer says that each cartridge has a maximum service life:

• prefilter - 3 months;
• filter elements with granular activated carbon inside - 6 months;
• membrane cartridge - 2 years;
• postfilter - 12 months.

But not always expendable materials serve for so long. After all, it all depends on the quality of the water itself, which enters the filtering system.

Replacing Atoll Cartridges- a task that can be solved independently. But if you have no experience with such devices, then it is better to entrust this matter to a professional from the service department. After all, making the slightest mistake, you can spoil not only the filter elements, but also the cleaning system itself.

The Atoll filter is a joint development of a Russian and American manufacturer, well known in Russia and the CIS countries.

Despite the rather high cost, it is popular, and there is whole line reasons.

We will analyze how and for what purpose reverse osmosis filters are used, how to replace cartridges, and how difficult it is to maintain the system.

Advantages of the Atoll reverse osmosis filter

Atoll filters are compact, reliable, durable and highly efficient water purification systems.

To the main advantages Atoll osmosis filter include the following:

• Products of this brand have international certificate NSF, which confirms both the quality of the ingredients, and high level cleaning in general.
• Filters do their job equally well in urban conditions and in the country.
• FilmTec membrane is the world leader among reverse osmosis membranes, manufactured in the USA. Productivity - up to 200 l / day, designed for an average family of 3-4 people.
• Pentek cartridges - produced in the USA, recognized as the most effective and high quality among all analogues.
• High-quality plastic and metal tank have a margin of safety, are resistant to water hammer and deformation.
• The system can be supplemented with a bioceramic cartridge, which helps to impart the properties of melt water, and a UV disinfectant (for a well or a well).
• The modern crane has an improved design and is recognized as ergonomic.
• Multi-colored commutation tubes make maintenance easy.
• Excellent build quality.
• High reliability.
• Availability and constant availability of consumables.

VIDEO DESCRIPTION

Atoll filter connection diagram

Atoll purification filters you can connect on your own without involving a specialist.

By purchasing filters of this brand, you get the following set:

• Water purification system with replaceable cartridges.
• Plastic key.
• Clean water tap and connection kits.
• Two plastic tubes 2 meters long.
• Water supply tap.
• Tee.
• Blue brackets to prevent accidental disconnection (installation optional).

• A - white tube - connects to a clean water tap.
• B - red tube - connects to the pipeline.

Step 1 - connect flexible tubes with quick-release connectors.

Attention! Make sure there is enough length for the connection before cutting the tubing. No tools are required for installation, the main thing is that the pipes are cut evenly, this will provide protection against leaks.

1. Cut the tube at right angles.
2. We insert the tube into the connector until it stops. It must be sunk 5-6 mm so that it is tightly squeezed by the connector ring.
3. Install the blue bracket to prevent accidental disconnection.

To disconnect the tube, remove the blue bracket, press the ring at the base, holding it in this position, pull on the tube.

Step 2 - Drill holes for a clean water tap and connect it to the filter.

- The place under the tap should have a diameter of 13 mm, while it is important to take into account that the length of the blue tube is sufficient to connect the tap of clean water to the filtration unit, and nothing underneath the sink or countertop prevents the installation of the tube to the tap of clean water.

When installing a clean water tap, we rely on the following diagram:

A set of parts is supplied with the crane, and the crane can also have a quick-disconnect connector. They will provide reliable sealing of the joints.

Options for connecting the tube to a fresh water tap:

The crane can also be mounted on the table surface.

Step 3 - We connect to the cold water line (the temperature should not be higher than 38C, otherwise the filter will fail).

Use clean rubber gloves when performing all piping work to prevent bacteria from entering the system.

1. We close the cold water supply valve. We open the cold water tap on the mixer and release the pressure. If it continues to flow, close the main valve of the house or apartment.
2. The system is connected to the water supply through the water supply unit.

- We assemble the water supply unit by connecting the tee and the water supply tap according to the figure:

We screw the water supply tap into the tee using the FUM tape. It is important not to damage the threads, so we use an adjustable or wrench.

• Loosen the union nut and disconnect the mixer and flexible hose.
• If necessary, replace the union nut gasket.
• Install the assembly into the gap of the flexible mixer hose:
• We connect the tube from the filter and the ball (or needle - depending on the configuration) water supply valve.

Step 4 - Flush and get started

1. The first cartridge is already installed by the manufacturer, the rest must be supplied by yourself. We unscrew the flask with a plastic wrench, remove the protective film from the cartridge and install it in the flask. We twist the flask with our hands without a key.
2. We open the water supply tap.
3. We open the tap of clean water.
4. Make sure there are no leaks.
5. After a few minutes, close the tap of clean water.

The system is ready to use!

Check regularly for leaks during the first week of use. The milky color of water is not a reason for worry, these are air bubbles that will disappear in the near future.

Atoll Filter Replacement Instructions

A special key is included with the filter, which is necessary for further filter replacement. This must be done every six months.

1. For convenience, we carefully remove the system from under the sink or countertop. To do this, we shut off the water directly on the filter and on the storage tank or the general water supply in the apartment.
2. Next, we take a set of Atoll filters with cartridges, take them out of the package.
3. Using a special key, unscrew the lower cartridge counterclockwise. We take out the contaminated cartridge, drain the dirty water from the flask and rinse it. We lubricate the O-ring of the flask with special silicone, which is included in the kit.
4. We release the new cartridge from the cellophane packaging. We put it in the flask and screw it back.
5. We return the system to its place.
6. We turn on the water supply and check for leaks.

How often to change replacement cartridges

• Porous polypropylene cartridge - every 2-3 months.
• Granular activated carbon cartridge - every 5-6 months.
• Mechanical cleaning porous polypropylene cartridge - every 5-6 months.
• Membrane - every 2-3 years.
• Postfilter - once a year.

The timing can be adjusted depending on the quality of the water. Even if the filter is used irregularly, it is extremely important to adhere to the replacement times, since the cartridges become a favorable breeding ground for bacteria during periods of “idle time”.

Why is timely replacement necessary? The answer is simple - this allows you to extend the life of the membrane, as well as provide high quality cleaning for many years.

Received the very first American company "Atoll" on the market. Atoll water filters act on molecular level... For over 20 years this company has been working on Russian market... In Russia, this company organized the production of such filters.

Such products can be of the following categories:

• household;
• trunk;
• industrial.

Some products may be softened

Filter quality

The Atoll water filter is the most reliable in our market. For achievement excellent quality products use several methods:

1. Components for these products are purchased only from trusted and trusted suppliers. All parts entering the conveyor are tested in multi-stage tests.
2. At such an enterprise, there is no random inspection of the quality of parts. Products leaving the conveyor are tested for tightness.

High level of water quality

The excellent water quality can be checked with special devices or you can order an independent examination that will help you find out all the advantages of such filters.

Filters "Atoll" are made according to the most innovative technologies, therefore, the water coming out of them is of a sufficiently high quality. This parameter is achieved as follows:

• all filter parts are created by manufacturers with vast experience in the world market and brought purification technologies to perfection;
• they do not contain artificially created compounds, and the products work with the water that comes from the tap.

The classics, tested by time and people, are present in every technological process... Each person can easily understand the working principle of such products. They worked on the design of these filters the best specialists in the industry. The Atoll water filter is easy to use and install.

Filter design "Atoll"

Many modern people prefer to buy the Atoll filter. The instruction, which is attached to each product, fully describes the entire structure.

Its features are as follows:

1. All filter connections are quick-detachable. This design facilitates quick disconnection and attachment of the device, which makes it possible not to use additional tools... Service becomes convenient.
2. Connecting tubules different colors allowing you to attach Atoll filters without errors. Inside the box there is a product passport, which describes in detail how to install a water treatment system.
3. The cartridges, which are replaceable filter elements, are known all over the world. This helps to purchase such products anywhere in the world, there will be no problems with the purchase of replacement cartridges. Each replacement element must be matched to the characteristics of the water.
4. For the convenience of users, a compatibility table is attached, as well as instructions for replacing used cartridges. Thanks to the table, you can easily find the desired element and replace it.

Original design

This product is subject to strict classic design... The colorful packaging contains a faucet with elegant lines. Choosing this particular product, you will not regret it, as you will get a really high-quality product.

Connecting this product

You can connect the Atoll filter yourself, but if you can't do it, then contact the service centers that work with these products. The set of these filters has a tap through which already purified water flows. It is embedded in a countertop or sink and is used for household purposes, regardless of the total water flow.

The entire filtration system is placed under the sink. Multi-colored tubes make it easy to install such a system. The set includes a storage tank with a volume of 12 liters. Sometimes a situation arises when the consumption of pure water increases. In such a situation, it is used pure water from this drive.

No need to look for a plumber you know to help you attach or repair them. Service centres maintenance of these filters will help not only to install them, but also to repair this filtering process.