Chipboard - the most suitable material For the production of reliable and high-quality inexpensive furniture. In order to hide not too aesthetically looking for the internal structure of the product, the end of the end is performed - installing special decorative panels from melamine, PVC or other available species of synthetic plastics.

Why still edge furniture

In addition to the most obvious goal - to provide an elegant appearance, the shaping of furniture performs some more equally important tasks:

Where you need to cross

Furniture manufacturers often make adhesion only visible parts end surfaces. From the point of view of savings it looks quite explained, but taking into account the above facts such an approach can turn into certain problems - the protective edge must be present in all places where there is an open internal structure of the chipboard.

If you have purchased furniture with unprotected edges, their raverity can be made independently at home. For this you do not need to have no special equipment - The edge can be glued by the usual iron.

Do not be lazy to spend a few minutes on this operation - you reliably protect yourself and your furniture and noticeably extend the service life. Next, we will analyze in detail how to properly glue the edge ribbon with your own hands.

Edge materials

The edge of the open surfaces of furniture can be performed using different decorative elementscharacterized by the quality of the material external species and, accordingly, cost.

How to glue the edge

Administration at production is made with a pure base. The adhesive composition is applied to it during the installation process when high temperaturesproviding the formation of a thin smooth layer. In order to glue the edge, several rollers are used, tightly pressing it to the base of the chipboard. Then, special cutters cut the ribbon to the size of the parts, remove the remnants of the glue and the material of the base and grind the place of the junction until the smooth and beautiful surface is obtained.

It is possible to stick the edge at home. To do this, use a tape with an already applied adhesive composition. The process further repeats the industrial edge, since it is performed similarly:

More details with the process of sticking edges on the chipboard you can read the video below:

Stick the P-shaped profile on the chipboard is somewhat easier. We have already discussed this method earlier. Such an edge is much stronger than melamine, quite easily bends and reliably protects against damage.

The presence of microloans between the edge of the P-profile and facial surface The chipboard does not allow it to glue it in the kitchen or in the bathroom, so basically the admission by this material is used for office furniture.

The edge of the chipboard, of course, is better to perform in the factory. In production, you can order a ribbon from any materials, including plastic, PVC and other modern composite materials. Racking on the machine will provide perfect evenness and accuracy decorative claddingBut requires certain costs. If the main task is to meet in a predetermined small budget, the application of the melamine tape will make it possible to combine permissible quality and the minimum price.

Perhaps you will be interested to know

This article is likely to not be interesting to professionators-furniture workers. But lovers who do not have for some reason the reasons for access to PVC edge with glued, but really want to bind their furniture to PVC-shock, it will have to be "on the cashier." Moreover, it is not only 2 mm, but also 0.4 mm PVC edge.

Today we will discuss the process of stickers of this type of edge not to traditional glue melt, but on the contact glue.

I use glue, but you can use the traditional moment.

Cut the edge with slices slightly large (about 10 mm) than the length of the stuck detail (I will glue ends in the photo). For cutting perfectly suitable garden secateurBut you can simply scratch the edge to the sharp object - it will break exactly at the place of scratch.

We apply glue to the part (some adhesives imply applying on both bonded surfaces - read the instructions).

Then we turn the part and lay it on the edge, pressing it to the smooth surface.

Now the part must be fixed until the glue is drying.

For this, you can use specialized edge clamps. I use - they are screwed into conventional F-shaped.

Crucify better through wooden lumps for a more uniform pressure distribution.

The second option is to use special clamps. I made such a pair of plywood and studs.

After drying the adhesion, we free the parts from the clamps and cut the ends. You can do this or the same secateur or again, protozapav and ottomiv.

In both cases, it turns out such a cut, which sometimes you have to bring a little small skirt on a bar.

Now we go to the removal of the scenes with the faces.

Glue edge to chipboard

For 0.4 mm, the edges are enough knife or ruler (similar to melamine). For 2 mm of the same edge, the edge mill will be required.

Figured () mill, going bearing over the edge, cuts its protruding part.

At the exit, it turns out such a few grungy cut, which must be soldered.

For this, a piece of felt make a few energetic movements along the edge. Having heated he spoil roughness.

As a result, it turns out such an even edge no worse than on professional equipment

Although more expensive and longer. The technique, of course, handicraft, but it has the right to life.

Posted in: Practical part.
Tagged: LDSP end

Design, processing, sealing the edge of the chipboard. Edging, edge, end, finish. Close up, arrange, process, separate

How beautiful to close edge of chipboard? Grinding plate finish, laminated edge treatment. Chipboard edges. (10+)

Design of the end of the chipboard

The edge of the chipboard is necessary in the manufacture of furniture. Your attention materials for the manufacture of furniture do it yourself.

Structure of edge of chipboard

The chipboard consists of sawdust mixed with glue and compressable. Moreover, the pressing process and drying of the adhesive is organized in such a way as to obtain dense surfaces and a rather trumped middle. This is done so that the chipboard spring is not broken. If the entire leaf array is made dense, the sheet will be trampled from very small deformation.

Usually we do not contact with the internal structure of the chipboard sheet. It is fend off from us with dense surfaces and laminating coating (if the chipboard is laminated). But the end opens this charm to us. Our goal is to close it from the eye of those who will admire our product.

In addition to aesthetic, there are several more reasons why you need to close the ends of the chipboard, even in places, not affordable. Moisture. The chipboard is very sensitive to moisture, even to a small amount absorbed from the air. The surfaces of the laminated chipboard are not allowed moisture, the surface of the polished chipboard is usually painted and also does not miss moisture. The edge also should not pass moisture. Mushrooms. Through the end in the stove, microorganisms and insects, decomposing wood, can penetrate. Harmful substances. Harmful substances contained in the glue and sawdust themselves, of which the chipboard is made, do not penetrate the laminated or painted surface, but they will be indoorated through the end.

Edge options, chipboard edge

Options for processing end (edding) depend, first of all, from how the sheet itself is separated. If the sheet is laminated, and it is planned to use its laminated surface to score, that is, not to paint and not covering anything, then on the visible edges it is necessary to stick the edge tape, corresponding to the type of laminated surface, and the hidden edges shape and flush the construction band. If the sheet is laminated or polished, and it is planned to paint it, then the leaf itself needs to be primed, its edges shaded, stuck with a construction bandt with an occasion on the sheet plane, scold the bandage and paint.

The end of the laminated score of the chipboard

Visible end

When drinking such a chipboard, you need to be very careful, to use a split tool leaving a smooth edge. Laminery chipboard with chipboard loves to crumble and roll out. If this happened, it will not be possible to correct the situation. I do not know how to clean such a chick. We will have to either come down, or block a new workpiece. Next, I recommend slipping the edge. Many glue the edge ribbon immediately on the cut edge, but I tried to do so and refused it. The tape is badly kept on such a surface. Puttling edge acrylic universal putty. After drying, the skin with the skin of medium grain. I do it very carefully, so as not to put the laminate with the chipboard. Further on the aligned surface sticking the ribbon.

I will focus on the types of tapes - edges. This usually happens paper (in a generalized understanding of the word 'paper') tape and plastic. Paper tape. Sold with the already applied thermoclaim. It glues iron. I will not stop in detail on this process, there is enough materials on this topic on this topic. You need to pay attention to the quality of the tape and glue. If the tape subsequently will fall behind, it will be possible to put it with conventional glue, it will not be noticeable. Plastic tape glue glue. Glue can be already applied to plastic ribbon. And covered with a paper protective strip. This is a bad case. Such glue is very bad glitter. Do not buy a plastic edge with already applied glue.

What glue glue? It is better to use the adhesive recommended by the manufacturer. But, note, It is worth making sure that for this glue there is a solvent that allows you to remove the excess adhesive and not damage the plastic curb and the coating of the chipboard itself. Then you will be comfortable.

How to glue the edge on chipboard and pvc

According to the instructions for the glue, you glove the edge, and the glue spoke to the tampon, moistened with the specified solvent. Difficulties may occur if the glue dissolves only by solvents that dissolve plastic. This solvent is impossible to remove this solvent, such adhesive is not suitable for us.

Registration of invisible end

Put it on it. Middle grain sandy skurt. Gently, not to spin, as in the previous case. In principle, this can be stopped. but better glue PVA glued to the covered end of the construction bandage strip. He (bandage) will prevent the splitting and rash of putty. Usually the bandage is somewhat wider edges. We stick the bandage so that the edge is in the middle of it. When the glue dries, a sharp knife, carefully, not to damage the laminated chipboard, remove the surplus bandage.

Eck of chipboard

In this case, the cut can be carried out without special feet, since chips and defects can easily be fixed with putty. If we work with laminated chipboardBut still we want to paint it, we appline the soil on all the product. Suitable GF-021 or OtEx (OTEX) from Tikkurila (Tikkurila). If a polished chipboard is used, it is not necessary to primitive, although it is desirable. Split the end. I use acrylic putty with a small filler. Skin. We must get a smooth rectangular edge. Sometimes for this requires several iterations of the skin - putty. When the edge suits us, it needs to be consolidated, otherwise it will fall or cracks. Putty - the material is not very durable and reliable. We glue the edge of a construction bandage to 4 - 5 cm than the end. We use PVA glue. Bandage bend so that he sticks to the dorsa chipboard and entered the upper and lower plane. See drawing. After drying the glue, the construction bandage of finely dispersed acrylic putty. It is usually used one putty for all these works. Especially pay attention to the strip, where the bandage ends and the chipboard itself begins. Here it is necessary to put out especially carefully, so that after the skin and painting the transition was absolutely noticeable. Such putty, whirl with a shallow eye, paint.

Despite the monstrous view of the scheme in an enlarged scale, in reality, the presence of bandage and putty on the end of the chipboard, if everything is performed correctly, completely not noticeable.

Unfortunately, errors occur periodically in articles, they are corrected, the articles are complemented, developing new ones. Subscribe to news to keep up to date.

If something is incomprehensible, be sure to ask!
Ask a Question. Discussion of the article.

More articles

Arc welding with your own hands. Electric welding. Tutorial. Welded Sow.….
How to learn welding work Alone ...

How to make reliable heating burner on spent oil? Scheme ...
We will make a reliable heating burner on the workout yourself. Homemade about ...

Glue is tight, firmly correct. We choose, select good, the best, ...
Let's learn how to choose glue and glue. Best glue - Suitable and correct ...

Homemade ladder. Do it yourself. National team, collapsible, sk ...
How to make a reliable folding staircase yourself ....

Close the baths of the bath + walls, tiles, tiles. Glue, stick, glue b ...
How reliably and longly close the baths of the bath and walls? If the wall is from the panels, plates ...

How to paint furniture with varnishing. Table, Wardrobe, Shelves ...
There is an old lacquered (polished) Furniture Seriously sevenpan, lacquering ...

The reasons for the reasons for the flame, weak or too strong burning plate ....
Kitchen fault overview gas stove. Weak or too strong burning, ...

Welding, electric welding, apparatus, welder. Transformer, straightening ...
How to choose a welding machine ....

Furniture edge PVC

The furniture edge of PVC is a narrow strip of polyvinyl chloride, which is used for pasting the ends of the LDSP. It not only protects LDSP from damage, but also is a decorative element.

The melamine edge is also widely used in the furniture manufacturing. But since it is made of paper impregnated with salt solid, has a number of shortcomings. Among them is a small thickness, short-life and exposure to mechanical damage. That is why many of the manufacturers of furniture and interior items prefer tape from PVC.

The PVC edge is distinguished by the following advantages:

• high level of strength;
• reliable protection against chips, moisture, which allows you to increase product life;
• high resistance K. chemical composition, ultraviolet radiation, ignition;
• relatively low cost.

The PVC edge is a narrow tape consisting of polyvinyl chloride. Edge ribbon - elegant addition to furniture designs From LDSP. It protects products from physical, chemical and biological damage, while attaching elegance furniture, be something tabletop, a stand or any other product. It is enough to get the ends of the furniture so that it acquires the finished look. The edge ribbon PVC is able to work miracles even with ordinary furniture, hanging her notes of refinement and sophistication. There is a huge variety of colors, shades, decor and textures as a result of what you can apply this decorative element to any furniture. In addition, the edge material will add furniture performance characteristics, protecting furniture from moisture and reducing the evaporation of the resin.

The furniture edge is easy to use and a very practical decorative element, which facilitates the operation of furniture from LDSP.

High-quality edge ribbon gives furniture products durability, reliability and durability. Ribbon is easy to wash, because it is distinguished by moisture resistance. The facing edge of PVC is additionally covered with an acrylic resin so that it does not expose any effect.

In the manufacture of furniture and components on an industrial scale, several types of tapes are used, including ABS, edge tape on adhesive basis and PVC. If we are talking about exclusive designer furniture or premium class furniture, then apply original edge materials, including aluminum edge, high gloss, 3D edge, etc.

One of the best edge ribbons is considered to be pVC products Production of China. This edge material is characterized by special aesthetic and functionality, as well as a long service life.

The edge of PVC China is performed in accordance with the latest achievements and for all sanitary and hygienic standards. Furniture edge China is considered the best option For furniture from chipboard and decorating an office or at home.

Our company offers a large assortment of PVC edges of different textures and colors. Focusing on your choice, we will offer you the glue that the edge material will most reliably attach to the furniture. Of course, the issue of accuracy of furniture design will be directly dependent on the quality of equipment and personnel qualifications. If you want to choose a unique stone surface or wood texture of a classic type, then we will help you choose the desired option. ribbon Edge.

Casting plastic edge of chipboard ends.

You will be left to specify the texture, decor and color of the material, in accordance with your taste addictions. With the help of the edge tape, you literally transform furniture in your home. Products, as well as its production technology, meet the highest standards of quality, safety and ecology.

We offer you the edge of PVC in a wide range of attractive cost.

Having saved the head of the chipboard by melamine edge, do not doubt that the treated surface will look worse than the edge paste on the machine of low quality - if you glue the edge correctly, according to the algorithm, the result is brilliant.

What is the edge glued?

• To parts in contact with the floor.
• To elements that will continue to be mechanically exposed.
• To inner details, for example, parts retractable boxes Chest or bedside tables, laminated plates.

What will you need for edge pasting

• Iron.
• Knife cutter or stationery knife, necessary thingYou can use, both when collecting furniture and when collecting various elements, for example, a mosquito net.
• Segment of felt or wet fabric flavors - rag.
• Emery paper, and what is even better - the bar, covered with sandpaper, will work with it it will be more convenient.
• Holder of details or vice.
• Actually the edge itself.

How to prepare for edge pasting

So that the end result of your work looks immaculately and looked quite aesthetically glowing edge, It is necessary to use a good iron, it is desirable that Teflon be taken as the surface. Make sure the ironing surface of the iron is clean - if there are pollution, they must be fixed. If you picked up this tool you can start the pasting for example the shelves of the cabinet.

So that the work was most comfortable, you should not use the usual knives, the cutter is perfect. If you do not have such a knife, it means you need to find the old canvas knife and independently construct cutter from it.

The bar can be made it yourself - it is necessary to take even an ordinary piece of chipboard and salary it with sandpaper on one side.

Melaminovskomka for sale with an already prepared layer of glue on it, but if you "lucky enough to buy the edge without adhesive coatingYou must independently apply glue on it.

The holder can also be easily constructed independently from the remnants of the chipboard, for this you need to take two small pieces of material and fill them at a short distance from each other perpendicular to the base.

The process of pasting edge is produced in stages

• Overlooking the bay, attach it to the end of the part, leaving some edges for trimming.

  How to glue PVC edge to chipboard at home

  In the standard, the width of the edge is 2.1 cm, and the chipboard, as a rule, has a width of 1.6-1.8 cm, therefore the stock will also remain for trimming and to strengthen the edges. In order not to make any extra work and do not cut the edge along from two edges, it is better to align it on one side, and further cut over only on the other side.

• Having attached the edge to the facade, start to heated and iron it. Special attention It is worth paying for the edges of the ends - it is necessary to stroke the most carefully.
• Details of small length are stroked entirely and immediately, and longer segments should be heated and stroke parts - sections of 40 centimeters. The end is cooled with a felt or a damp cloth.
• Based on the quality of the tape used, the iron heating temperature is selected and adjustable. If everything is set correctly, the iron straight slides on the surface, it does not cling to and does not scratch the edge. If the heating is correct, the adhesive under the edge will be strained evenly. And if you overdo it and overlay the edge, then bubbles will go and the edge will have to remove and throw out.
• If you still spoiled some kind of plot, then in order to remove the spoiled material, it is necessary to heat it again and take it off the knife. Cleaning the surface can be started to bother again.
• If the edge is high-quality, it will stick, only after complete cooling. Finding that the edge completely cooled, you can proceed to pruning too much. It is possible to trim correctly by starting the edge, losing it by BRO, until the chamfer will be visible white color. Seeing the substrate already you can cut unnecessary material.
• After trimming, all edges neatly and thoroughly rubbed the bar with sandpaper. At this stage, the occasion of the melamine edge ends. And you can safely start installing the handles.

What kind of edges are, as well as about the ways of gluing them and how to glue the edge with iron and hairdryer, you will learn from this article.

1. The most common view - the edge of the melamine with glue on paper based . It is used to finish the inner sections of furniture. Affordable, inexpensive, but not the highest quality option. Does not tolerate moisture, rapidly wear out. It is easily glued at home by a simple iron.
2. T-shaped flexible profile - represents a T-shaped bar, it is inserted into a slot in the side of the chipboard or MDF. The damaged element is further conveniently replaced without flashing furniture. For installation, the milling machine will be required.
3. PVC Cant - reliably protects the ends of furniture from damage, is distinguished by wear resistance, resistance to moisture. To glue the PVC Cant, the edge processing machine will be required, so the use of this type of edges at home is difficult.
4. ABS plastic is an eco-friendly version without chlorine. It is valued for resistance to high temperatures and physical damage.

All options can be divided into two subspecies - edges without glue And with glue.

The average cost of the profile for one time-meter:

• PVC thickness of 0.4 mm - about 25 rubles,
• PVC 2 mm thick - about 40 rubles,
• Material from melamine for chipboard - about 25 rubles.

In our country, they actively use products from Rehau, which offers big choice color solutions, as well as different width Ribbons from 15 to 45 mm.

To simplify work, you can use various specialized furniture programswhich calculate how many materials will be needed for gluing edges.

PVC edge - how to glue at home

To work will be required:

• iron or construction hairdryer,
• and of course buy PVC edge with glue
• hard roller
• newspaper or paper sheet

The material is heated so that the glue becomes sticky. Heating is performed by iron in synthetic mode.

• The profile is applied to the end so that it overlaps the end of the site.
• Next, the iron is again performed through the newspaper. Since glue dissolves quickly, the process is active enough, and the iron is conveniently moving along the PVC edge.
• The edge itself needs to be carefully pressed and stroke until it sticks along the entire length.

1. Priphescing with a construction dryer. Instead of an iron, you can use a construction hairdryer. PVC edge is heated from the adhesive side and when the composition becomes sticky, the material is applied to the end of the desired site, clamp and gently smoothed.
2. Glitting with the help of "moment" glue. This method is suitable if there is no adhesive layer on the edge. The end quality is checked manually, remove sawdust, litter, dust, until the surface is clean. Then on the material, and glue and wait for the end and wait until it grab. After that, apply and pressed. Using a roller, the area is rolled so that the glue grab quickly.

How to remove excess material

If it was not possible to gently glue the edge from the first time, the procedure will have to be reused. To do this, glue again and pinch a profile using a roller or manually.

Since usually the PVC edge width is taken with a margin, you need to safely remove the surplus along the edges. To do this, use the usual stationery knife or file. It takes both hands and pressed on the protruding fragment. As a result, the extra pieces are laid out and the edge remains that coincides in the width with the site.

After everything glued, it will remain to treat the irregularities of sandpaper.

Melamine edge is optimal option For use at home, when it is necessary to restore old furniture from minimal cost. If the furniture is expensive, it is better to turn to professionals that use another more expensive and high-quality material.

Consider how to glue the edge on the worktop from chipboard At home.

Great video on the topic

The following materials will be required for work:

• sking
• sharply sharpened knife jamb,
• roller for gluing wallpaper
• melamine edge
• construction hairdryer or iron.

1. choose an iron operation mode so that it does not heat up too much and burns the chipboard and at the same time ensured proper melting of glue,
2. edges of chipboard under the sticking to handle sandpaper, eliminate irregularities,
3. measure profile
4. it is necessary to heat it with an iron and tightly press to the area with a roller (if there is no adhesive layer, it will take self-applying glue to the edge, for example, the "moment" glue),
5. cut with a knife hanging edges.

Trim needed at an angle along the edge, slightly climbing the material. Then it will remain skin to handle edges so that there are no burrs and irregularities.

If the edge of the edge and the chipboard itself, the details are slightly different, the simulator will help correct the difference.

In the case when the item has complicated formAnd the edge of the surface is characterized by complex relief, the first time does not always succeed exactly glue the material. In such a situation, it is worth contacting professionals in order not to spoil the product.

Types of adhesive

Professionals furniture production Actively use melt glues for edges. They are convenient if production is supplied to the stream, and it is required both high quality results and fast speed.

Melt adhesives are thermoplasts, that is, when heated, they become very elastic, and when cooled quickly solidify. For these properties, an ethylene polymer with vinyl acetate is responsible for these properties. The lack of use is to attribute the need to use special equipment, namely the corresponding machines or manual pistols for applying glue into parts and warm it up.

1. In domestic conditions, PVC glue, which glues well paper Materials to various surfaces. Uniform without lumps light color The mass glues the surface well, but moisture is afraid. It does not require the use of additional equipment, therefore it is convenient for the operation of non-professional masters.
2. Universal adhesives "Moments and" 88-Suite ", which reliably stick the material to the surface of the chipboard and PVC. After 3-4 hours, the product can be used. Adhesives are inexpensive, secure and available.
3. From professional furniture glue for edges It is worth noting the products from Kleiberit. The company offers adhesive adhesives for cladding, for gluing the material by the soft-forming method (in case the surface is embossed), as well as for cladding.

In this article, we will look at the easiest option - this is a twinkling of 2 mm edges with a predetermined thermoclaim. You can order such an edge either in the supplier company or in the workshop. Poster to its value will be 2-5 rubles per meter.

For sticking such an edge, we need a technical hairdryer (thermopystoletole), a milling mill (desirable edge), a hawk mill, a sharp knife, a file and a hb glove.

Fix the item vertically or horizontally - as you are more convenient (it is desirable to fix it with clamps).

First, we warmly warm the tip (about 5 cm) edges so that the glue melted, and the edge itself became soft.

We apply the edge and, having warmed the glue with the flow of air, together with the end of the part, smooth the edge with the hand in the glove. Warming up the site is about 10 cm long, lay the hairdryer and more carefully stroke the site and so each time. The main thing is not to overheat the edge (the overhaul edge is easily beaten - just itself - and in this case there will be visible places of beggars in the form of waves).

We look at the glue seams again, the non-flimsy places warming the hair dryer again (and you need to warm with front face, having warmed the whole edge) and smooth to full fit.

Go to cutting sinks. If you have an edge mill, then everything is fine, if only a universal manual, then it will require refinement, because It is not possible to put it on the edge of the workpiece - sink interferes.

I screwed a piece of LDSP to the sole, which made it possible to raise the sole only on the one hand.

Then I, of course, made myself a normal edge - I will use it in the lesson.

First, practice on trimming, to accurately adjust the cutout cutters, otherwise, risk damageing the laminate. So, for example:

The milling milling mill (radius of rounding 3 mm) neatly, not swinging on the harvesting planet, cutting off the excess edges.

I turn over the other side and repeat all the manipulations for smoothing the jambs and cutting the soles.

The remains from the ends are cut as follows: we carry out with a pressing a sharp knife on the edge, forming a scratch. We put the workpiece to the edge of the table on the line of scratches, after which we are shaking it down.

Or screaming a piece from the end his blade (The main thing is not to scratch the adjacent edge perpendicular to the spilled).

Survegencies and roughness are run by a file.

As a result, something like this should turn out. For clarity - the straight (short) piece of the edge was glued on the machine, and the long (which covers the bend) - with your hands. The difference is practically not visible.

In the manufacture or repair of furniture, masters have to be separated by the edge of the product. For this purpose, a special face edge from PVC is most often used. Several popular methods for gluing the specified framing on the chipboard are described below in this article.

How to mount the edge of PVC self-adhesive

The edge based on polyvinyl chloride is sold in two versions. In the first embodiment, the glue layer is applied to its lower part in the factory. In another embodiment, the edge is sold without it, and the glue has to be applied on their own.

If the material has an adhesive layer, it should be warm up first. After heat treatment, the glue will become sticky and the edge will easily stick into its place. This is done with the iron to be switched to Synthetic mode.

The edge attacked the end to which it must be glued. At the same time, the edge completely overlaps the end of the workpiece. Then carefully, with the help of iron heated the edge. But it should not be done directly. It is better to stroke the product through the layer of the newspaper.

Print such material easily. As heated, the glue dissolves and as soon as this happens, the iron moves on. The edge itself is well pressed against the workpiece and smoothed. So act until the edge is glued to the part along the entire length.

Installing the edge with a construction dryer

By the way, it is possible to glue the edge without an iron. Sometimes it is more convenient to use the construction hairdryer. For this, the edge must be heathed from the reverse side, where there is a layer of glue. When the glue becomes sticky, the edge is applied to its place, pressed and smoothed.

How to glue the PVC edge to "moment"

If the product does not have an adhesive layer, you need to take a "moment" and apply it yourself. But before applying glue, you should check the end of the workpiece on quality. There should be no garbage, dust and sawdust. The end must be clean and durable.

The glue is applied immediately on both surfaces. That is, on the edge of PVC and on the end of the workpiece. It should not be in a hurry. It is necessary to wait until the glue starts to be captured and only after that the edge can be highly pasted into its place.

While gluing the framing, it is strongly pressed against the workpiece and smoothed. It will not hurt to roll the edge with a hard roller.

How to remove the extra part of the edge

If the edge glued well the first time, you can proceed to the final stage. If not, the procedure is repeated. Need to apply more glue On the problem area and turn it hard or rolled it with a roller.

How to remove unnecessary? The fact is that the framing is usually wider than the workpiece itself, therefore it is necessary to remove excessive width. Make it using an ordinary file by neat climbing.

The file is taken by two hands and a plane of pressure on the protruding edge. At the same time, it is clogged and becomes closed with a blank. Like the framing follows the workpiece, and not from it - so less risk that the edge will be corrupted. However, if the PVC edge was qualitatively glued, it ourselves is ideal and this part of the work never causes special complications.

Final grinding material

To finish the work on gluing PVC edges, you need to take a small emery paper And stabbing flaws, if any. Everything! The framing is glued and ready to use.

Chipboard is the most suitable material for the production of reliable and high-quality inexpensive furniture. In order to hide not too aesthetic looking internal structure of the product, the end of the end performs the edge - the installation of special decorative panels from melamine, PVC or other available types of synthetic plastics.

Why still edge furniture

In addition to the most obvious goal - to provide an elegant appearance, the shaping of furniture performs some more equally important tasks:

Where you need to cross

Furniture manufacturers often make the adhesion of only visible parts of the end surfaces. From the point of view of savings it looks quite explained, but taking into account the above facts such an approach can turn into certain problems - the protective edge must be present in all places where there is an open internal structure of the chipboard.

If you have purchased furniture with unprotected edges, their raverity can be made independently at home. To do this, you do not need to have any special equipment - the edge can be glued by the usual iron.

Do not be lazy to spend a few minutes on this operation - you reliably protect yourself and your furniture and noticeably extend the service life. Next, we will analyze in detail how to properly glue the edge ribbon with your own hands.

Edge materials

The edge of the open surfaces of the furniture can be performed using different decorative elements that differ in the quality of the material, the appearance and, accordingly cost.

How to glue the edge

Administration at production is made with a pure base. The adhesive composition is applied to it in the process of installation at high temperature, ensuring the formation of a thin level layer. In order to glue the edge, several rollers are used, tightly pressing it to the base of the chipboard. Then, special cutters cut the ribbon to the size of the parts, remove the remnants of the glue and the material of the base and grind the place of the junction until the smooth and beautiful surface is obtained.

It is possible to stick the edge at home. To do this, use a tape with an already applied adhesive composition. The process further repeats the industrial edge, since it is performed similarly:

More details with the process of sticking edges on the chipboard you can read the video below:

Stick the P-shaped profile on the chipboard is somewhat easier. We have already discussed this method earlier. Such an edge is much stronger than melamine, quite easily bends and reliably protects against damage.

The presence of microloors between the edge of the P-profile and the front surface of the chipboard does not allow it to glue it in the kitchen or in the bathroom, so basically the adhesion is used for office furniture.

The edge of the chipboard, of course, is better to perform in the factory. In production, you can order a ribbon from any materials, including plastic, PVC and other modern composite materials. Racking on the machine will provide the perfect evenness and accuracy of decorative cladding, but requires certain costs. If the main task is to meet in a predetermined small budget, the application of the melamine tape will make it possible to combine permissible quality and the minimum price.