13846 0 4

How and what to sharpen mounting foam In 3 stages

Do not know how and how to sharpen the mounting foam? The experience gained by me allows you to say that all necessary materials There will be in the nearest construction store, and anyone can cope with the task. Detailed illustrated instructions will help me prove it.

From the preparation of materials before applying the solution

Is it possible to put the mounting foam? It is not easy, but even need. This is done to achieve two goals:

1. Protection against the harmful effects of ultraviolet. Despite the mass of positive performance, the mounting foam has one fatal disadvantage: it crumbles for a long time under the sun;

1. Decoration. The yellowish clubs of frozen mass around the door or windows look not very aesthetic. It is better to close them with something more attractive human eye.

For the same to perform the task, you need to:

1. Prepare Tools and MaterialsHaving visited the construction store if necessary ;
2. Prepare processed surface, that is, bring the dried substance to the species suitable for putty ;
3. Apply shp can.

Step number 1: Preparation of instruments and materials

Before starting work, make sure that you have:

1. Primer. Will the shtatlevka hold on the foam without prior priming? It will be, but much worse, plus the level of danger of its detachment will increase in the future. Why risk?

1. Two spatula:

• Wide - for applying a solution to the treated surface;
• Narrow - for applying a solution from a container to a wide spatula;

1. Shplanke. Depending on the place of execution of work, use the following rules when choosing a suitable solution:

• Street - Facade mixtures based on cement or polymers. As an example, consider specifications NEOMID putty spitches:

Prices in the article are relevant in the summer of 2017

• Room- Gypsum spatlets for internal work. As an example, consider the technical characteristics of the mixture of Knauf Uniflot:

If we are talking about room with high humiditythen it is also better to use facade formulationsSince the gypsum in such a medium is deformed and destroyed.

• Ceramics or heat insulating plates - Adhesive shovels. As an example, consider the technical characteristics of the Weber Vetonit product:

If we are talking about the sealing of slopes, you can additionally acquire more sealant and strengthen them the edges of the mounting foam so that they do not begin to crack over time.

• Ribbon-Serpecafor reinforcement of the plated layer;
• Gloves. The price of such an accessory is low, but the hands will remain clean;
• Mounting knife For trimming surplus dried mass.

Step number 2: Preparation of the treated surface

The putty on the mounting foam does not fall without preliminary preparations:

Photo	Description
	Cut With your own hands with the help of an assembly knife, all protruding excess the frozen foam.
	Apply Using roller primer.
	We wait Frozen soil.

If we are afraid that you can blot the window with a primer or putty, then put it in advance with a painting ribbon. You just remove it after the end of the work together with all the accumulated mud.

Step number 3: Applying a shplanie

After the primer freezes, you can proceed to putty:

Photo	Description
	We mix shp can This can be done manually, but a building mixer will give a greater homogeneity.
	Applythe first layer of putty on one of the side of the window perimeter.
	Clear In the putty tape Serpiank.
	Applythe second plaque layer covering the sickle ribbon.
	Eliminate Rafting surplus splatters that fell on the window frame.
	Similarly close up All visible plots of mounting foam.

Conclusion

You got acquainted with how and what to put the mounting foam. Video in this article contains a number additional Materials. In the comments, you can ask additional questions.

If you want to express your gratitude, add clarification or objection to ask the author - add a comment or tell me thanks!

Can not imagine modern construction Without the use of mounting foam: This material serves for broad spectrum Works and used to seal almost any slots and cavities in the building. The foam quickly freezes and ensures reliable protection, but the appearance of the joints is not very attractive, in addition, that the foam serves as long as possible, it must be protected from adverse effects.

The inspidation and sound insulation indicators of the material can be maintained over the past many years if it is securely protected from ultraviolet radiation Sun, it can destroy the composition in just a few years.

Features of work

Consideration of the issue, how to launch a mounting foam, you should begin with the process of choosing materials and the preparation of the instrument. Using right devices Significantly facilitates work and allows you to achieve an excellent result, even without construction qualifications.

The choice of composition and tool

So, what to launch the mounting foam so that the coverage is reliable and durable?

The following factors should be taken into account here:

• Where the premises will be performed for many more compounds, while with an outer putty, the solution must have water-repellent properties, tolerate the temperature differences and not collapse with the sun.
• The thickness of the layer and the width of the gaps. As you know, the putty should be applied with a thin layer, while even significant differences can be equalized by the plaster. This aspect is easy to determine by viewing all places requiring treatment, we note that most often it is advisable to use a plaster mortar.

• Features of the room in which sealed seats are close. For example, a cement composition is best suited in the bathroom, which is not afraid of moisture and has high reliability, gypsum compositions can be used in conventional premises.

Tip!
The choice of a specific option depends on you, we only note that the Rotband plaster is very good for finishing the foam, the composition for the fogenfuller seams and other similar solutions with elevated strength properties.
For outdoor plaster on cement or latex based or glue composition For tiles or heat-insulating plates - it also has high properties.

What needs to be purchased before starting work?

Here everything is simple enough:

• Purchased required amount Mixtures (it all depends on the volume of work, and determine how much the composition is needed, just even on the eye). As noted above, for interior decoration Well fit gypsum plaster, Outside it is better to use the weather-resistant compounds, otherwise the repair will not be durable. Any plaster over the foam primarily performs protective functions, so high demands are presented to it.

• To process the base, you will need a primer composition. The choice of a specific option depends on the features of the base, the desired type you can easily choose in any construction store. In extreme cases, you can use the universal acrylic composition, which deeply penetrates the structure of the base and strengthens the surface.
• If there is a finish of slopes, the stakes of the frame and plaster are needed additional protection, since cracks are most often formed. It is best to purchase a stained sealant - the price of its low, but the benefits are undoubted. It is simply used: after the decoration, the plaster is removed at a distance of approximately 3-4 mm, and this cavity is sealed.

Tip!
Application of the composition is easiest to produce with a narrow and wide spatula.
A narrow solution is superimposed on a wide one, and with its help the mixture is distributed over the surface.
The work is quite simple, and the main thing in it is accuracy.

• It is necessary to knead the solution in the clean, convenient for the capacity of the tank.

Preparation of the foundation

This stage is quite simple, but its importance is very high, so you should not neglect the following operations:

• At first, it is necessary to cut all the extra pieces of foam to sharp knife - the surface should be smooth without protrusions and recesses.

• In the presence of unreliable sites and pieces of the old coating, they should be removed, and all distressed places close with cement mortarSince it is not recommended to apply too thick layer of plaster.
• The surface is thoroughly cleaned from dust and dirt, it is better to do this with a vacuum cleaner - it will remove dust from all irregularities.
• Before starting work, the base is processed by the primer composition, it will strengthen the basis and balances the absorption in all areas - the plaster on the installation foam will be very better and dry uniformly.

The working process

Consider how to stack the mounting foam with your own hands:

• Initially, the solution is mixed as the instruction requires. Do not prepare too much mixture, it should be enough for about half an hour of work.
• Next is applied to the surface, if 1 cm layer and more, it is better to finish in 2-3 layers, so the surface will be much stronger. Remember that the minimum layer must be at least 4 mm, otherwise the composition will not protect the foam properly.
  
• After drying, the surface is polished and processed at your discretion: or damage with wallpaper.

Output

In fact, to separate the mounting foam is quite easy - the material is unpretentious and represents durable base. The video in this article will help you understand some nuances of work even better.

After installing the windows and doors, the hosts and the wizard finishers are often wondering - how to close the mounting foam? It can be hung up using putty, sealant, paint and other materials. It is important to do this correctly by applying the appropriate technique that describes below.

Mounting foam - comfortable material

Today, the mounting foam is used in many construction work. It is a polyurethane foam two- or one-component sealant, which is produced in a special aerosol can. Used in two cases:

• for thermal insulation;
• sealing seams.

Suitable for materials such as wood, glass, metal, concrete. The main component of foam is polyurethane, which was first created by Bayer in 1947. In the 70-80s began to produce first splashes and apply them for finishing work.

At the same time, in addition to polyurethane, polyisocyanate and some catalysts were added to the composition. First country this materialwas Switzerland. Later foam began to use other countries. Today it is used in Europe, Asia, USA, Russia. Such widespread is associated with unique properties material. Foam easily penetrates any gap and seam, fills the space and quickly hard. Thus, this site is perfectly protected from various adverse events.

Why do I need to protect the mounting foam?

As already mentioned, the composition perfectly fills the space inside the gap and seam. But at the same time she also needs protection. The fact is that foam is destroyed under the influence of UV rays and moisture. If you do not protect it, then the overall operational period of such a seam will be not more than 5 years. That is why after applying it additionally misses special compositions.

But the question arises - how to protect the mounting foam and which means it is better to apply? For these purposes, sealant, putty, plastic liquid, acrylic paint, can be used. At the same time, the coating should be waterproofing and countertile. That is, providing proper ventilation and protect against water penetration. Therefore, when choosing compounds, pay attention to their properties (usually described on the package). Also, some consumers are used to protect a special sealing tape. It quickly passes on the desired area and is suitable for both old and new designs.

Protection by plaster and what should I know for this?

So, on the question of how to close the mounting foam, there was already an answer. But how to do it? Consider an example of finishes using plaster. Treatment begins with removal of excess material. It is necessary in order to align the base. In the case when the use of plaster or putty is assumed to protect, it is better to additionally deepen the surface to a couple of millimeters.

The second task that occurs in front of the finishing masters is the question - how to sharpen the mounting foam? What kind of putty and plaster choose? It is better to use a frost-resistant composition that is sold in building supermarkets. A good brand is Rotband. Sold up the composition in dry form and is prepared immediately before use. And if the question is exhausted, then you can proceed to the direct preparation of the mixture. The recipe is always written on the package.

The solution is poured into the water and is carefully stirred so that there are no lumps. If you have too thick composition, it is better to add some water.

The putty is applied using a spatula or trowel. The layer should be equal to at least 4 mm. Since if you apply too thin layer, it may soon crack (usually it happens when drying). At the next stage, the coating is given for some time on solidification, but do not wait for complete drying. Then the surface is poured with a fine-grained sandpaper or a construction grid.

Please note that all the works described you can easily do yourself. It is important only to follow the instructions. Therefore, the question than to smell the mounting foam should no longer occur. Also when performing work it is necessary to wear gloves to protect the skin of the hands. All tools are washed after use. warm water. The residues of the composition are removed in a dark place.

In all construction and installation work Often you have to resort to sealants, the most popular of which is a mounting foam. This type of building material was so tightly entered our lives that we consider it an indispensable tool intended for the sealing of small seams ,. However, it must be hidden under finishing materialAnd for this you need to know how to close the mounting foam.

Very often, foam is also used for sealing slots and doors. Such popularity is easily explained by her operational characteristics And the fact that it always eliminates the problem as much as possible. Today, this material is a polyurethane foam sealant, which in most cases is released in an aerosol cartoon. You can find the mounting foam on the shelves of all construction stores in a huge assortment. Applied construction foams In two cases:

• for thermal insulation of the premises;
• sealing seams.

Mounting foam is in demand due to the fact that it is excellent for materials, such as wood, metal, glass, concrete. Unfortunately, because of its unusual external view She does not always fit into the exterior interior of the room or premises. It is in order to preserve its special characteristics and at the same time make an invisible, it is necessary to close the foam to other material. Most people have no idea how to close it, so the masters immediately call if such works are required. However, everything is simple enough, but, even without having special education, skills and special knowledge in the field of construction.

If you used the mounting foam for work with the outside of the premises, be sure to remember that with all its durability it requires constant protection against ultraviolet and blowning. If you do not protect the mounting foam from exposure adverse factorsThe term of its service will be significantly reduced to 5 years. Sometimes, when, in order to avoid such situations, the cooled foam is lubricated with a special solution of primer.

Required suppression materials

Many are asked: what to close the mounting foam? There are several options: a conventional sealant, putty or a pre-compacted self-adhesive tape.

To cover the mounting foam, it is necessary to approach carefully, because it must necessarily be a water insulation and countertile. According to experienced and qualified masters, there will be an excellent choice for outdoor work. The usual spittle is for sale in the form of a powdered mixture, which is required to breed a certain amount of water to obtain a special solution. You can find a puttyle in almost every construction store. Pay your attention to the frost-resistant option of outdoor spitels: their range is large enough, based on this you can choose exactly the one that will most comply with your financial capabilities.

To reliably close the mounting foam, you will need to be in advance with such materials as:

• spatley for outdoor work;
• small sizes knife;
• capacity for solution;
• water;
• latex gloves;
• master OK.

Technology of entry work

First of all, you will need to prepare the surface of the mounting foam. Cut upper layer Foams from the surface. Next, put on the gloves and proceed to the preparation of the spreading solution for outdoor work. The solvent of the wrapper is not very much, so you overdo it. It is better to knead less and then finish what to translate expensive building materials.

You can find directly on a pack with a putty. With the help of a trowel, apply a crude putty in such a way that you have the opportunity to quickly align it until it starts to stick. In some cases, cracks may appear. This is due to the fact that the layer is too thin, it is for this reason that a layer of a thickness of several millimeters should be applied. It is also not recommended to apply thick layers of the twin, as it will be squeezed in the drying process. The proper application of the layer of this building material will allow preserving a pleasant appearance of your work and reliably embarks the mounting foam.

After drying the applied putty, the processed using emery paper or construction grid. Do it to remove roughness and give seams that were close to, aesthetic and neat appearance.

Another way to protect the mounting foam from the impact on her moisture and ultraviolet from sun ray is an sealing ribbon.. This tape is in most cases used to fill holes and irregularities in various overwhelms that arise as a result of installing new designs.

Each owner wants his house to look flawlessly. With the help of the method described above, you already know how to smell the mounting foam, and you can easily hide tracks from sealing slots, as well as protect the trimmed surface foam from adverse weather events and other harmful factors. The main thing in the likes is not to rush, because the accuracy and the final result of the work done depends on your movements. Best patience and you will definitely work out.

How to smell the mounting foam - the question that has recently arises somewhat. Various external factors lead to a deterioration in the state of the mounting foam, which in a certain may not cope with its direct appointment. Therefore, we consider proven ways that will allow you to smell the mounting foam without special costs time and strength, but guarantee the quality and reliability in which modern metal needs plastic windows.

How to smell mounting foam- reliable protection windowRehau for a long time

Mounting foam as a result of the impact of moisture, light and other factors after a while loses its qualities. Including foam, gradually gaining moisture. There is a violation of the peculiarities of thermal insulation. Therefore, experts recommend in advance to think over the slopes and sealing foam from the outside and under the windowsill. The slopes in the windows are important - after all, they allow you to hide the presence of assembly seams, contributing to the durable exploitation of the entire design as a whole. First of all, it should be determined optimal Material For slopes.

The simplest option becomes dry mixtures. Sun can be performed using standard plaster. But for this option, the preparation of the wall under the material is initially required. In the presence of large slots The layer is required to the wall of the wall, using special mixes. Among the necessary funds it should be noted putty for outdoor work, gloves, a small knife, trowel, water and a solution for a solution.

How to smell mounting foam - Verified Action Complex

Cut off an excess dry foam outside the joints. When used to seal the putty, it is recommended to cut the mounting foam into several millimeters for a thicker sealant layer outside. A smooth surface of frozen foam is recommended.

Next, putting gloves, prepare the sealant solution to perform external work. For this, we will not need a lot of solution, so it will be better to miss less, then you can add as needed. The instruction of the preparation of the solution is contained on the packaging of the material.

The mass of the putty is applied with a knife or a trowel - choose with personal preferences and places of sealing, align the surface. After drying the very thin layer of putty, cracks may occur. To avoid such trouble, it is better to apply a layer of solution of a few millimeters - taking into account the appearance of the construction.

So it is possible to protect the mounting foam from the effects of the rays of the Sun, which can lead to a destructive effect. Due to this, it is possible to protect the foam also on the effects of moisture, which when penetrating from the outside leads to the destruction of slopes and other elements of the compound. The aesthetics of construction improves.

Best Effect white slope It is achieved using a water-free mixture under the plaster. Works are performed using special tools. Sunza plastering mixes It will be an excellent choice for the outside.

Slopes out plastic panel

Perform slope from the plastic panel is significantly easier. From a large panel in the size of the slope, cut pieces for 3 sides of the window. Special plastic rack creparate panel to the window.

The installation of the side panels is made at an angle of 90-110 degrees relative to the window. Mounting each panel to the wall is made, with filling the mounting foam slot between the old slope and the window - for best insulation. After the foam dry, get rid of dried residues. Between the panel and the wall, the resulting clearance is closed, tightly joining the F-shaped rail.

Plasterboard slips are performed like plastic. The installation can be performed in two ways - setting the prepared panels to the profile or gluing for glue. Thermal insulation is ensured by insulated mineral Wath. After installation, the drywall panels are processed by primer. Next is done painting. To ensure a fully level angle, glittered with a plaster corner with a putty.

All this proves the possibility of using various methods When finishing the PVC windows. Today, plastic windows remain the preferred option, which become the key to the excellent properties of hydro and thermal insulation, durability and reliability. The use of drywall slopes contributes to the preservation of heat and resistance to moisture. But plastering of slopes as finishing outdated, given the rather weak protective properties, which are not enough for modern PVC windows.

How to smell mounting foam- Help professionals, confidence in each decision

Still working with window and door structures Requires some preparation and experience for the reliability and quality of the result. Therefore, for many, it is preferable to contact professionals that can guarantee the claimed result at affordable prices - on the company's website always provides data on services, detailed information can be clarified by managers. Smear mounting seams and carry out related work on modern standards Quality.