What enjoyment in nature stretch out in a hammock. Rise or read the book on fresh air. But the trouble is: even if there is a hammock, it may happen that there will be no two in the right place suitable treesto hang it. In this case, a skeleton for a hammock comes to the rescue, which can be installed in any place convenient for you.

• braided;
• fabric.

Braided hammocks are net, like fishing, only woven from a thicker rope or rope (2-3 mm) in one or two threads. And the network is woven so that the cells (side 5-7 cm) in relation to suspended device Romes were oriented. The length of this network is usually 2-2.5 m. The width of 1.5-3 m. The edges of the network from two opposite sides are attached to durable placamswho cut the cloth. Next, ropes are collected in the harness, which ends with a fastener loop or ring.

Tissue hammock (Mexican Cocoon) is made from a solid piece of durable fabric (tent tarpaulin, sail, dense upholstery). The two opposite edges of the fabric are going to the harness, to which the rope with a fastening loop or ring is attached.

It was for these two loops or rings a hammock to be attached to two supports located at a distance of at least 4 m so that the hammock slightly resolved, but was quite stretched. The fastening height is so ( about 1.5 meters) So that a person can easily get into him, but to be kept under weight, he did not touch the earth. Supports must be very durable. If these are trees or inserted pillars, the diameter of them should be at least 10 cm.

The dimensions of the chapels of the hammocks are approximately the same and depend on whether it is calculated per person or for two.

There are, however, hammocks for seating. Then the cloth has a smaller size, and the suspension can be placed on top. Such hammocks are convenient to hang in the arbors.

The stability of the hammock is an important factor. And although the solitary mount of the hammock makes sense, allowing it to rush in it, like a swing, but with a smaller amplitude, there are hammocks that have two suspension on one side and one on the other, or two suspensions to each side. In this case, the possibilities of swinging is significantly less, but the stability of such a hammock will be maximum.

The designs of hammocks are considered as detailed, because they directly determine the design of the framework.

Designs of carcass hammaka

The carcass hammock makes durable materialcapable of suffering quite large The load is determined by the weight of the person and voltages arising from possible swinging. Usually frames make from metal pipe, Round or rectangular profile, or wooden bar, straight or bent.

The design of the frame is to carry a vertical load from the weight of a person and the side, tipping, when swinging or landing in a hammock, determine its shape and composition of the main supporting structures. There are two of them. The first is - vertical Ramato which a hammock is attached. Second - horizontal crossmen - The legs to which the frame is attached, and which, leaning on the ground, do not give the frame to overturn. The width of the legs should be at least a meter. And the one and other designs can be performed in different ways. But the main two constructive differences relate to the frame. It can be made in the form:

• dougi., like a rocker or stretched onion ends up;
• as low horizontal trapezium Below and ends directed apart and up.

In the first case, the frame is made of a metal pipe or a bent wooden bar. In the second of the pipe and the segments of the direct wooden bar.

The bottom of the frame is strengthened additional elementsWhat makes her wider and strengthens the fastening towards the legs. Structural elements are attached to each other welding (in the case of a metal pipe), bolts with nuts, screws and screws (in the case of wooden design). Nuts B. bolted connections, given the dynamic nature of the load, must be strengthened lock nuts or spring washers With a cut. All design elements are covered with paint or varnish.

Frame design for hammock can be stationary or collapsible. Stationary design Designed for continuous use in the country or near the house with pomidery territory. Collapsible - good for trips to nature.

More easily apply different designs. For example, the frames can be two, articulated in the upper part and fitted below, performing the role and frame, and legs. Frame can be made in the form parallelepipedalike a house. In this case, the hammock is attached simply to the upper cross.

These two designs are good for hammocks with two fasteners on each side and are more likely to be suspended bedthan a classic hammock.

For the terrain, devoid of shadows, you can find a construction with a roof of a fabric, mat or skid. It is usually mounted on separate brackets And attached to the frame.

Expensive sets of extra class are complemented mattresses and mosquito net.

Materials for hammock

Metal used for frame - steel, sometimes galvanized steel covered with an additional layer of protective paint.

Wood - This is usually a timing of 100 × 50 from a variety of breeds of a well-dried tree. For the legs, pine is usually used, for the frame beech, glued pine, red wood, tropical wood.

For fasteners, remembering the outdoor operation, bolts, nuts, washers, screws and screws made of steel with zinc or copper coating are used.

Manufacturers and cost of carcases for hammocks

Frames for hammocks are manufactured many countries World. The most popular are products from Italy, Brazil, China, Russia and Ukraine.

Budget Chinese and domestic collapsible models made of metal tube stand from 3400 rubles. (Frame for hammock number 1, Murom) and 3500 rubles. (Leco-IT Green, Kazan) up to 7600 rubles. ( wooden frame For hammock Izhevsk). The frame of the Massif of Pine Ultra (Stary Oskol) will cost 18 152 rubles. Italian hammocks of bent tree Can cost from 22,000 rubles. (Venezia) up to 148,000 rubles. - Set of complex wooden design of bent bar with hammock handmade, mattress and mosquito net.

Most frames are sold with warranty year or two. However, most manufacturers prophesate to them a long life in 20-30 years with neat operation.

A hammock frame can be made own hands. Typically, they are made independently frame from a wooden bar. On the Internet there are a large number of examples, based on the appearance of which, you can make a painted frame. But there are both examples of assembly with a consistent description of operations and drawings.

The main material for the manufacture is ash-tree bar and boards. The frame design consists of two sinks (1800 × 60 × 80), mounted at an angle of 45 0 to the strapping of two boards (2000 × 40 × 80). Each of the divosers is additionally strengthened against the shifting force with two angular blocks (166 × 622 × 60), also mounted on the strapping. Together they form a solid trapezoidal carrying construction.

The bottom of the frame is mounted two paws of the base (1000 × 80 × 800) with bucke ribs (80 × 150 × 25). On the disclosure, at the level of 1.38 m from the lower plane of the scaper are installed two ry-bolts to which will be attached Gravity hammock. The whole design is assembled on bolts (M10) and nuts and can be disassembled for transportation and storage and tag is quickly collected for use anywhere.

In conclusion, we can make sure that if the framework is required for a hammock, you can find the most diverse designs For every taste and wallet. When buying should be paid to the protection of the material from which the framework and fasteners are made. After all, the framework will work outdoors, exposed to ambient. When operating, it should be remembered that the service life of this useful, and sometimes the one's cheap items can be extended if there is no way to hide it from direct exposure moisture. In the design of the frame there is nothing complicated and any person who is friends with tools and tend to make, can make a frame for your own taste, spending only on materials.

A comfortable hammock will always be a favorite holiday destination for the whole family. How nice after work on panstone relax in the fresh air and showing in a comfortable hammock among high trees. And it is not necessary to acquire it in the store, as this subject of the country exterior can be easily made with their own hands.

Types of hammocks and their features

For the first time, Hamamak appeared in the Indians of the islands of the Caribbean. Since it was impossible to sleep on Earth, the enterprising aborigines invented such a device as a hammock. Seeing such a comfortable and safe bed, the Spaniards immediately took it to armared, and later they had already enjoyed numerous inhabitants different countries. Naturally, over time, the hammock was significantly modified and modified, and now we can choose any design of the hammock at its discretion: from tissue, wicker, from wood, etc.

By its design, hammocks can be:

Types of hammakov

1. Brazilian hammock is a modification of the Mexican design and is intended for people who are accustomed to maximum comfort. It can be switched on ropes if you use special straps and hard cross traverse. The width of such a product reaches two meters. It is quite expensive and complex in manufacturing design, since certain loads from the places of hanging "are located" on the fabric are much more complicated than on the grid, so it is necessary to install such a product with a large number of branches and scenes.
2. Mexican hammock can be made of fabric or ropes. It does not have hard details. Since it consists only of a piece of fabric and several ropes for stretching, it can be worn with me in a bag, backpack or a gluable bag. The disadvantage of such a product is the need for large quantities Fabrics (about 3 meters long and 1.5-2 meters width). To hang it between supports, a large distance is needed. It can not be done double, as it will take a fairly large piece of fabric, which will be folded in the Cocoon Tight, which will do the stay in it not quite convenient. You can be in such a hammock you can not more than two hours, as the back is starting to hurt and you can not talk about comfort.
3. Vietnamese or Malay Hammak is made of a solid fishing network and is suspended by several branches-supports with different degrees of load. Since such a design was not very convenient, the inhabitants of Asian countries decided to supplement it with transverse stripes - traverses. This is a comfortable bed that can be easily made double. There is an unlimited amount of time in such a hammock, without experiencing painful inconvenience.
4. The Brazilian hammock for seating is a reduced and simplified design that is attached on the suspension of a trapezoidal form. Such a suspension chair can be manufactured with a half-row design or completely rigid. That is, a hammock - a chair can be completely wicker from natural or artificial rattan.

Photo Gallery: Hammocks of various types and designs

Wicker hammock chair has a steady wooden frame Hammock rocking on metallic frame can be installed anywhere Wooden hammock chair will perfectly decorate the country area or children's Corner A bright and spectacular knitted hammock-chair can be made with your own hands. Fabric hammocks stronger wicker Suspended tissue hammock with two fasteners can be taken with you Frame hammocks can be of various shapes and any color Sleep in the hammock is not only comfortable, but also useful Since the hammock is used in hot weather, it is very important that the material was eco-friendly and passed the air well In a hammock without transverse planks, it is easier to keep equilibrium If there are no suitable trees on the site, hammocks can be placed in a gazebo Hammocks wicker chairs will decorate at home and street

What is better to do a hammock: pluses and cons of fabric and grid

Regardless of the design and type of hammock you need to know several general rulesthat will help in the manufacture of a convenient and durable product.

1. Cloth for making hammock. Properly selected fabric will significantly extend the life of the product and increase its strength characteristics. In order for the hammock to be durable and reliable, it is necessary to choose dense fabrics, such as sail, tarpaulin, tick, jeans or camouflage. Materials from synthetic fibers are no less durable, but they do not let the air, so it will be not quite comfortable in a hammock in a hammock.

   The fabric for hammock should be as strong as possible, but at the same time passes the air well

2. Ropes or ropes for a wicker product are also selected, based on their strength, practicality and comfort. It is best to acquire products from cotton threads. With such ropes, it is more convenient and easier to work, they are reliable and tighter in knots and weaving, as well as pleasant to the body.

   It is best to acquire ropes from natural threads

No matter what you choose for the manufacture of hammock (cloth or ropes), you should not stop at cheap synthetic materials. If we talk about what is better: Fabric or rope braided meshHere everything depends on the preferences of the owners of such a design. The fabric is more dense, less passes the air, so even in cool weather in such a hammock will be comfortable and cozy. The grid product is ideal for hot and exhausting summer. Even a small light breeze blowing from all sides, a wicker hammock will create a wonderful bed for recreation.

If we talk about the complexity of making a hammock from the fabric, then it will make it much easier and faster than weighing a fishing grid or learn Macrame technique. Therefore, you can just buy a ready-made solid grid that will serve as the basis for the manufacture of a rope hammock.

Preparation for the manufacture of hammock: drawings and schemes

Before starting work, you need to know some rules for manufacturing a hammock design.

We will sew a fabric hammock with dimensions of 3x2.2 meters. To do this, we need a durable mattress tick, a hazard or camouflage fabric. So that the hammock is convenient and roomy, focus on an adult (man). Therefore, we use tissue to the entire width.

As a frame for hammock use wooden details. It is best to purchase a web-wide 3.6 meter width, but you can take two pieces of 1.4 meters and just sew them together. If you take the sail, you need to consider what is on the usual sewing machine To see such material will be very difficult.

For fastening the design, we need a durable rope or linen rope from cotton fibers.

Calculation of material and tools for work

For the manufacture of different options Fabric hammocks We will need certain materials and tools.

Fabric hammock on crossbars

Materials:

• durable fabric - 3x2.2 m;
• singry procession - 50 cm;
• pig - 5.2x3 cm;
• fal from Capron - a cross section of 4 mm;
• wooden bar - cross section 4 mm;
• sandpaper;
• acrylic paint.

Instruments:

• metal ruler - meter;
• chalk for marking fabric;
• wood hacksaw;
• chisel;
• small brush;
• scissors;
• pose and ordinary needles;
• centimeter;
• sewing machine;
• iron.

Pashed parts have a smaller thickness, they are easier to shoot and do not need to hold the cloth with hand.

Stages of manufacturing hammock

1. From the wrong side of the material, we draw two rectangles with dimensions of 1.5x2 meters. Cut out the pattern and add them facial side to each other.
2. We retreat from the edge of 1.5-2 cm and on both sides we grasp the short sides of the fabric. Soak the workpiece is obvious. The lower part will perform the role of the back, and the upper faces. Rejusting the allowance for one side.
3. We sew a sling on a long part of the detail with an indention along the edges of 5 cm. On the back of the sling is paced along the entire length, and from the front side at a distance of 35 cm from the seam. Further, the lower part of the workpiece is wrapped on the upper, without cutting the sling.
4. We prepare 4 pieces of slings with a length of 70 cm. Send them to the specified places of fasteners, face to the back. We string the edges to create holes for the crossbar.
5. We shoot the lateral long sides of the product on the front side with a step of 30 cm from the edge. From the synthetone, we cut the strip of 25x125 cm in size and put them in the prepared pockets. Then we turn, hover and spend the edges so that you have a kind of rolls on the sides of the hammock from long sides. In order for the synthetone to fasten well, we spend the pockets with a steady method in several places.
6. Wooden bar cut into two equal parts. We note from two edges by about 2 cm and we make a recess of about 1 cm. We take out the unnecessary chips. Emery paper We clean the cut parts and stain the bars acrylic paint. Leave drying.
7. From the two ends of the product, we retreat at 5 cm and spend the strokes for inventing the crossbar. Running bars, we evenly submit the basis of the hammock on them.
8. Two crossages tie the Fal from Capron, so that the nodes are in the grooves.

Hammock of fabric on the challenges

You can make a slightly different modification of the tissue hammock on the chapers with wooden racks.

Materials and tools:

• durable material - 2.7-3 m;
• reverses - 22 pcs;
• tools for their insert;
• rope 35 m long, diameter 6 mm;
• metal large rings;
• electric drill and drill 12 mm;
• brussia 30x50 - their length should correspond to the size of a hammock in width;
• sewing machine;
• chalk for marking fabric;
• scissors.

Stages of manufacture

1. Measure the piece of fabric and cut off 2.7 meters. The edges are threatened by about 6 cm and spend on a typewriter. Then we destroy them, again we fell and spend.
2. We celebrate chalk on the fabric in the width of the place of fastening of chalks with the same step. We will succeed on each side of 11 pieces.
3. In the marked places, cut out small holes and a special tool for creating champs in them. Our canvas for hammock is ready.
4. For the strut, we take 2 bar with holes burst into them at the same distance as the chapens on the hammock. They will hold the cloth from folding under the weight of people.
5. Stretch through the holes of the ropes.
6. Mount the hammock slings. To do this, we make a special frame. But you can not do it. To do this, on the hook we are secure a metal ring, a hammock lay out on the floor and fix it with a heavy press.
7. On the frame we make a strut. I skip each sling through the lover, and then through the hole in the strut and the ring. Rope Return back. After completing all the work we associate its ends. Ring wept the remaining ends of the sling. Just do it on the other side of the hammock. Hinder it on supports.

All wooden structural elements we are styling, and then cover antiseptic. After that, they can be covered with varnish or paint.

Video: How to make a fabric hammock

Hammock-swing

Such a small hammock for seating can be easily made from the cut slicing of the fabric and children's metal hoop (Hula-HUP).

Materials and tools:

• durable fabric - 3x1.5 m;
• hoop with a diameter of 90 cm;
• sintepon - 3x1.5 m;
• repovaya durable tape - 8 m;
• sewing machine;
• scissors;

Stages of work

1. We cut out of the fabric two equal squares, the size of 1.5x1.5 meters.
2. Each fold four times.
3. To make a circle from it, from the central angle with a radius of 65 cm we plan a circle and cut it out. Also make the second round.
4. We plan holes for the sling: we fold the quadruple circle and stroke it so that the bends are reference points. The first pair of sling will be placed relative to bending at an angle of 45 0, the second - 30 0.
5. Also reproduce a syntheton.

   To make the same slits on both circles, connect the sections of the fabric and we rush them with pins

6. We lake the syntheps between the two parts of the material.
7. We sew a typewriter two identical covers. Then we sew them together, putting the metal hoop between them.
8. To the hoop in four places, we tie the rep a ribbon, cutting it into 4 equal parts.

   Ribbon can be set or just tie with a sea node

9. We bind free ends to the thick trunk of the tree or another frame at the required height.

We have a comfortable and small hammock, which does not require several supporting racks.

Video: how to make a hammock chair

Braided hammocks have already been known for a very long time, since in our country they were used everywhere unlike fabric. In its most, their base resembles a conventional fishing or volleyball net, which is suspended between two trees.

Consider a hammock with a length of 2.5 meters and a width of 90 cm.

Materials and tools:

• two wooden rails thickness - 1.5 m;
• ropes or thick rope 170 meters - diameter of 8 mm;
• scissors;
• electric drill and drill;
• brush;
• varnish or paint;
• antiseptic;
• metal rings - 2 pcs.

Stages of weaving

1. In the planks we drill holes in a step of 4-5 cm.
2. Cut 20 meters of the rope, which will go on fasteners. A 150 meters cut to equal parts of 6 meters.
3. Each rope is secure loop and tie the knot on the bar.
4. We choose any weaving scheme with a cell size at least 7 cm.
5. After graduating, we attach the ends of the rope by nodes to the second bar and for two slats we make fasteners. To do this, use metal rings.

   Ropes are fixed on a wooden bar with loops and knots

6. Check the strength of the product and attach to supports.

Video: how to make a wicker hammock

How can you hang hammock

In order to suspend such a hammock into two trees, you need to fill with special support bars on trunks. They will not give the Falu sliding down.

But it is best to use metal or wooden pillars, driven at a certain distance from each other. To the columns at an altitude of about 1.5 meters, you need to privar special hooks. If this wooden supportsYou can make special hoops with hooks.

Wooden frame for hammock

You can independently make a wooden framework for a portable type hammock. For the manufacture of such a design, we will need:

• wooden timber - 80x80 mm;
• board - 100x30 mm;
• studs, M10 bolts and nuts;
• hooks for hanging hammock;
• schlifmashinka;
• saw electric circular;
• electric drill;
• keys;
• paint or varnish;
• antiseptics.

Stages assembly

We will make the bottom support from two bars 3 meters and two transverse bars of 1.5 meters. Two side mounting beams are made from a bar of 2 meters and two stops of 1.45 meters.

1. Initially, we make bodies. This side part of the rack, to which we will hang a hammock with the help of hooks. To do this, the beam and focus is secure between themselves and scold at the bottom so that we have a sheer, but durable and stable detail with collapse at the upper points at least 4 meters.

   The finished design should withstand not only the vertical load, which the human weight creates, and and tilting

2. We set the side elements and fasten between 2 longitudinal bars. They must be in a mirror "reflection" from each other.

   The width of the legs should be more than 1 m

3. The transverse bar is made of two boards, 1.3 and 1.5 meters, and place them one top to provide our design maximum stability. In the end, the longitudinal bars fasten with transverse straps at a distance of 60 cm from each end.

   For assembly, you can use bolts or screws

4. I grind all the wooden parts, cover them with an antiseptic and give dry. Then cover with paint or varnish.

Second version of the carcass

The second design is more convenient and for it the same materials and tools are needed as in the first version.

In this case, we make the way we make a little different way, as well as add a handle with which you can easily climb from hammock.

Metal design

By the same principle, if desired, you can weld a metal support for a hammock from profile pipes Square or round section.

Video: Metal stand under hammock

If you adhere to the right technique of making hammock, then you will get a comfortable product where you can relax in hot summer days. Fabric or wicker hammock is an excellent option that will replace the bulky expensive garden furniture, And thanks to their mobility, hang such a design in any convenient location on the household site.

A frame for a hammock with your own hands can be collected in a matter of hours, if you know how to do it. Himmak himself is pretty convenient device For rest by country plot And in nature. For the history of the existence of this adaptation, many varieties appeared and functional modelswhich are quite different among themselves.

The most popular - suspended hammocks, but to fix them, you need two trees, or two rods that can not always be found on the site. You may need a special framework that will become an excellent support for the hammock. How and from what it should be done will be described below.

Appointment of carcass

In most cases, suspended hammocks are used. They are cheap and comfortable. The only inconvenience that may occur when using them are a limited number of places where they can be positioned.

In order to suspend the hammock, you must have or two next to the growing tree, or at least two columns. But such a design will still be stationary, without any opportunity to transfer a hammock to a more convenient place, and they are not very convenient to mount the posts around the site.

To correct this shortcoming, many companies have released various models of frame hammocks. They differ from the suspended, only the finished portable design, on which the hammock is fixed. A high-quality framework will cost decent money, and the Chinese cheap does not always justify the expectations. What then to do? Describe the frame itself.

The most common materials for arrangement of a frame hammock - wood and metal.Both of these material are capable of withstanding heavy loads without deformations.
A cheaper option is a tree. Of course, with his finish and other trifles will have to tinker, but the effect will be incredible. It is possible to make a metal support, but for this you will need special machines that can bend metal under a strictly defined angle. Since the second option is not available, one should consider the first.

Back to the category

Rectangular design

To start work, the following tools will be needed:

• screwdriver;
• wrenches;
• brush for painting work;
• grinding machine or sandpaper;

Materials will need much more:

• bars of pine, oak or ash with a cross section of 70x80 mm 1.5 m long - 2 pcs. and 1 m - 2 pcs.;
• 2 BROs from the same tree breed, only with a cross section of 25x70 mm in length 2 m;
• 4 more brus 25х70 1 m;
• radial hooks - 2 pcs.;
• bolts with a length of 140 mm and a diameter of 10 mm - 2pcs;
• enamel, Morid;
• galvanized screws or screws with a length of 50 mm;

The order of work is as follows:

1. First of all, it is necessary to see wooden blanks. If there are sharp edges, they need to be stigled or polished. After preparatory work, You can start an assembly of construction.
2. The semi-one-meter billets with a diameter of 70x80 mm act as racks.
   To the lower end part of the rack bars, we attach a blank-cross-line 25x70 mm with a length of 1 m. There should be two T-shaped blanks.
   At a height of 120-130 cm from the ends of the resulting racks can be placed hook mount For hammock.
3. T-shaped billets are fastened with two-meter brus 25x70 mm on both sides of the end.
4. 70x80 mm bars and 1 m long should be cut so that they can be connected at an angle of 45 °. It is necessary to position them so that they move away from the racks of the part and walked inside the design. Next, fasten with self-drawing at the place of the junction with the rack.
5. Under the diagonally located bars, you need to put the remaining pair of crossbar and fix the reasons from the bottom.
6. Attach the hammock and test the structure for strength.

If the design has withstanding, you can do the decor, apply the veil and enamel.

Hammock - the key to excellent summer holiday in the country. About how to make a hammock with your own hands here. And today we will talk about how to make a stand for a hammock of wood with your own hands.

For it is not enough just to make a hammock it still needs a story somewhere. And the wooden frame is the most optimal optionavailable to everyone. It can always be bought, but you can make it yourself. So cheaper will be appearance The finished rack will fit into your landscape design.

When you make a skeleton for a hammock with your own hands, pay attention to the security technique! Especially if you have little children. First, all sorts of nuts and bolts, try to drown in the finished rack, and the extra sticking threaded parts are better to cut. Well, take care in general about the reliability of your rack for a hammock - choose thick boards and a bar, and make the bottom of the bottom (so that the stand turned over).

Rack for a hammock made of wood drawings with dimensions

Let's start our selection of a master classes from consideration of a simple drawing of a hammock rack.

In general, it is quite convenient to work with a tree, so, for those who grow hands from where it is necessary, all drawings and ideas will be simple.

Stand drawing for hammock №1

As you can see a fairly simple design.

This wooden frame is worth from:

• The bases are two timber in the center (in the photo under the letter "A") and the strength of the legs (on the drawing "D");
• The beams "B", which are attached between the lower bars. At their lower part there should be a cut at an angle of 45 ° - so they will be screwed with a slope, which will significantly increase the space for hanging hammock;
• Stubborn inserts in the figure signed "C". On the one hand, hepts at an angle of 45 ° (this part will be connected to the beam). And the second edge remains even, it is fixed at right angles between two boards at the base.

There is a bonus on the drawing - under the letter "E", it is a stand for an umbrella from the sun.

Of course, the stand for a garden umbrella is an add-on, without which you can do. But surely there will be those whom it is useful. After all, not everyone in the courtyard in the country or at home there are trees or gazebo, creating a shadow. And so it can be hiding from the scorching summer sun. In this case, you will need to add only one piece of timber to your frame, with a hole drilled in it under the umbrella handle.

In addition, who has free time And the question with the Sun is relevant, I advise you to look into another our selection: how to make a frame for a hammock with a canopy and roof.

In the drawing, all sizes are indicated. Of course, you can change them at your discretion. And now a small master class with step-by-step photos.

The result is a beautiful wooden frame for a hammock, while it is convenient and it can be easily moved.

If you doubt the reliability of this rack, simply take the timing thicker. Of course, in this case, move one ready frame for garden plot it will be hard. But there will be no doubt in his strength - and its carrying capacity to increase.

I found a video with a similar rack from a bar 100x100.

Studs fastening cut:

• The first on 4 parts of 25cm - fastening the legs;
• The second part of 3 parts 33cm (+ from the third sliced \u200b\u200ba piece of 33cm) - intermediate connectives;
• The residue from the third is to connect the struts diagonally with carrier beams.

And here is another option to upgrade the original drawing.

Under paragraph No. 9, he was shown to the upper part of the carrier board of the hammock - this is an option for fixing a hammock without screws from a loop, a ry-bolt or anchor bolt. In general, for those who do not have them and do not want to buy.

Please note: the connection of the bearing board with a stubborn fastened plywood pieces from two sides.

And one more option of a wooden rack for a hammock. This time, is used mainly a small bar, and the stubborn inserts are made of boards and are placed on both sides (on the photo the right lower corner).

Frame for hammock do it yourself drawing number 2

The second option is similar to the previous one, here we also make the foundation, but the mounting option carrier beams And the strut is changed. They change places, of course, and their tilt angles change.

For resistance at lateral loads (swinging) to the finished rack from a tree, it is necessary to add cord / rope or metal cable - in photo №6.

Video example.

Cool video lesson with double strut.

By the way, the finished rack can be painted in some beautiful colour. The author painted his frame for hammock in blue colourYou can paint into your favorite color.

This video review for those who are afraid to bind to corners not 45 °.

Above presented to you an example of such supports from the bar. However, it can be calmly assembled from the boards. We watch step-by-step photos.

And of course video - for greater understanding. In fact, such a stand can be easily gathering one or with a small help of the wife.

Yes, and little leisurers (who has) will always be happy to come to the rescue - especially for testing the finished rack for the hammock.

And now consider several simplified examples. Bearing supports (those on which hammock hangs) can be attached to the base perpendicularly, so on the stubborn boards, the sections will be made up 45 ° (subject to the formation of an in-sized triangle).

And by the way, for greater stability, the stand for a hammock can be made not 2 legs, but four.

In addition, the ready-made rack can be decorate with night lanterns. So it will be possible to enjoy the evening rest in a hammock.

Or such an option: the bearing boards are additionally connected to each other, and the legs of the hammock are fixed to the ground. True, the pegs sticking out of the ground confuse me - I would not advise you to leave them. If you really want to attach a hammock to the ground, then do it with the help of fittings as shown at the top of the photo in the middle. Well, in general, of course, in this case, it is easier to concrete two bar and between them hang a hammock.

Third Options for Hammock Stands

We smoothly switched to the next version of the wooden rack. In the schemes, everything has signed in detail. It is going from the boards.

If you process all the board - rounded edges, etc. The result pleases the eye.

Simplified option.

Therefore, the principle can be made racks for a hammock from a bar.

By the way, a cable or cord is also useful here to stabilize the rack.

Their fixation near.

If the cable is not, you can use the boards by analogy.

Actually, this technique is applicable to the previous stands of the stands.

Inspired by other people's ideas, you can come up with your unique rack for hammock.

Here are some more interesting ideas.

Rack for a hammock in the form of a frame, if you remove the hammock, children will be able to use it as a football gate.

And here is unusual option, You can work hard to make this beautiful stand in the room to the child.

Folding Wooden Stands for Hammock

Thinking beautiful frames for hammocks are great, but there is no place for storing them. The summer season will fly quickly, and in our weather conditions a wooden rack is better to remove (so it will last much longer).

So I bring to your attention small selection folding racks.

The first rack, in the assembled form looks like one of those that we have considered above.

However, it is very convenient to develop, which is allowed to save place in the yard and the garage.

Specially frosted the boards different colorsso that it is clear how it works. Hopefully understand.

But you are a very simple version of the folding wooden rack for a children's hammock.

Couple useful videos examples.

This interesting option Stands are made of plywood, on the structure resembles racks from previous video.

Frame for hammock with her hands

All previous drawings are applicable to Brus, moreover, we have given examples of racks made from a bar. However, I carried a couple of options separately because they are fundamentally different from the previous stands.

Let's start with the most beautiful, in my opinion, the frame. See what is he delicious, and most importantly reliable. Such a rack will decorate any garden.

All parts are cut from the bar of the same diameter. In the photo under 1 point signed the length of each piece from this rack. The edges on each cut is mirroring at an angle of 45 degrees.

In general, work can be divided into two stages:

1. Cut the bar on the necessary pieces, cut the corners;
2. Start assembly (with the help of screws we collect all pieces into a single design).

The result is just excellent!

The next type of struts are widely represented in stores you can easily buy.

But if you want to make such a rack at home with your own hands, and cook iron corners as in the video you do not have the opportunity. Pay attention to the fastening corners that are sold in building stores. With their help, you can collect the rack no worse, and she hardly hurt your pocket.

Combined variant with drawings (from boards with construction corners).

And at the end an extremely unusual stand for a hammock from a bar.

Original bent wood frame

And dessert one of the most elegant: a rack for a hammock from bentwood.

I present to your attention a video lesson with the manufacture of such round carcass For hammock.

By the way, the supports for hanging chairs are made by the same principle.

And I still wish you good experiments on this!

Make a skeleton for a hammock with your own hands is a good idea. These products cost quite expensive, and their design is simple. Therefore, to create a rack for cottages will not be difficult. You just need to choose fit drawing, acquire some materials and spend a few hours of time.

A lot of effort will have to apply if you need a stand with rounded shapes, as in the photo. In this case, you need to have a special tool for wing of wood. It is quite labor and requires a certain experience. For beginners there are simpler drawings.

What to do?

Rack for hammock with their own hands is made of wood or metal. The complexity of working with both materials is approximately the same. Below are drawings of frames for giving from wood and metal.

Frame from a tree

Wood support has for a long time Services, strong enough and aesthetically attractive. It will become not only a useful item for a pleasant stay, but also to the decoration of cottages.

In the work you will need:

• saw, electrolovka or Bulgarian;
• hammer, kiyanka;
• screwdriver;
• furniture conductor;
• clamps.

Materials:

• Wood. The beams and boards are needed.
• Hardware - self-tapping screws, screws, nuts, washers, hooks (fishing).
• Furniture glue or PVA.

The stand is created in several stages:

1. Preparation of all parts of the future design.
   • Base. It consists of two 1850 mm long beams and two boards with a length of 1500 mm. On the beams, at a distance of 200 mm from the edges, grooves are made. Depth is equal to the thickness of the boards used, the width is the width of the boards. At the ends of the beams, at a distance of 20-40 mm, the bolts are made. The beams are stacked on the boards in parallel to each other at a distance equal to the thickness of the supported beams used (to which the hammock will be hung). For better fixation, you can connect them with a joinery of joinery or pva. At the same time, it is necessary to clamp in places of connection.
   • Supports. 2 beams are 1700 mm long beams. At one end, a cut at an angle of 45 ° is made on the other - a hole under the hook. There are also 2 supports with a length of 520 mm.
2. Opening with varnish. Since the rack will be used in the country, in the open sky, it can be opened by alkyd compositions - the smell will quickly disappear. Before processing, it is necessary to protect all the holes.
3. Build construction. If the items are made correctly, then there will be no problems with the assembly - the drawing provided above will allow you to perform work without difficulty.

Metal framework

The presented drawing demonstrates the rack made by metal pipes and special connecting elements. Supports of support can be chosen independently, depending on the dimensions of the hammock, the amount free space in the country. The main thing is not to change the widths of the support. The drawings indicate the optimal value that will be guaranteed to make the product stable. Connection locations can be additionally secured through through bolts. You can also cut the thread.

Frack of bentwood

Such a product is well suited for those who love complex tasks. Frame has simple designThe most difficult thing in the work is to bring the beams. To give a tree such a form, you need to soften, bend and dry it. Material plastic can be made in several ways:

• Farm finish. The beams are loaded into a pre-prepared box, steam is served in it. For each centimeter, the thickness of the beam requires approximately 1 hour of processing. You can also process the steam generator.
• Till B. hot water.
• Use an ammonia solution. The longer the tree is in it, the plastic becomes.

After the necessary softness is achieved, wood is strung out. For this, special machines are used, or they simply put the beam on the supports, and the cargo is placed in the middle. The greater the bend and the longer the material, the higher the supports will be required.