Plywood vases drawings. How to make an artistic plywood vase with your own hands

Wooden vases look very nice. Usually done on lathe... But 90% of the wood turns into shavings.
There is a technology that allows you to make a vase from a flat panel.

Here's what happens:

For a long time I chose the material for the sample. On the one hand, I want something interesting, on the other, so that I don't mind spoiling it.
As a result, I settled on walnut, with oak and wenge inserts.

Walnut board 75mm wide and 15mm thick cut into 3 pieces.
4mm oak veneer must be cut into 15mm dies.

How to do it if not circular saw but have a pair of clamps and a scoring saw?
Like this - the pistol is clamped between the nut dies ...

And sawed.

As a result, you get an even plate of the required thickness:

I glue the walnut into a shield with spacers - two oak dies, between them a thin wenge veneer. (which was sawed using the same technology)
Saw scratches visible. Slight sloppiness, plus hard oak, which sawed along the grain.
It's not scary, all the same, the shield will have to be sanded in order to even out the gluing errors.

And again I glue it with spacers, leave it overnight:

I level the shield with a belt sander, remove the remnants of the glue. Probably it was worth making the wenge continuous:

The result is a shield with a thickness of 14 mm. It took 0.5 mm from each side.
Based on the shield and the desired dimensions of the vase, the angle and step are selected:

I print the drawing, with the help of an awl I combine the centers of the shield and the drawing, I glue the drawing:

I saw a small staff at an angle of 38 degrees:

I fix the shield with clamps on the jigsaw table and using the rail as a guide, I drill 2mm holes with a drill at an angle of 38 degrees:

I thread a file into the hole:

And let's go!
Cut through the first ring:

And here it is - the bottom!

The wood is very hard, sawing slowly, if you squeeze it a little, the saw will burst. To replace the file, you need to return the table to a horizontal position, unscrew the saw attachment, thread the shield, adjust it to 38 degrees again, adjust the tension ... Moreover, the file almost always breaks when 3 cm remains before the end of the ring.

The second ring, the picture begins to emerge.

Bottom view:

And after the fourth ring the files ran out. I used up one and a half packs. No more, I put it off until tomorrow.

I drove into a store, bought 8 packs of files (to be sure it would be enough), sawed:

Shift the ring:

Sleight of hand and no fraud, rings fold into a vase:

Can be combined with a shift. You can make inserts between layers. There are a lot of options.

I begin to glue, while without a bottom, so that it is more convenient to grind the inner surface:

Checking the alignment of the layers:

I leave it under load overnight:

Result. The surface is rough, but the line alignment is not serious.
Darkening - marks from sawing with an ultra-thin file (41 teeth per inch), which was drowning in sawdust and the wood was burnt.

It is necessary to level the inner surface.
Attempt number one - a steel rod with sandpaper glued to double-sided tape.
Not an option, too flexible.

Attempt number two, grinding drum on the same spindle.
Also not suitable, the machine is light (as I intended it). It does not hold, plus it is inconvenient to work.

Attempt number three. Sanding drum on a flexible arm.

The drum is small, sawdust fly to where it is least needed, but you can work:

For fine grinding, I collect 400 sandpaper petals:

But it doesn’t polish. I continue with my hands.
It takes a long time, the surface is far from ideal.
I find an error - the penultimate ring is glued in with an offset of 180 degrees.
Well, it will be a reminder ... In the end, it could have been much worse. Let it add charm - it will be a border. The main thing is that the spacers are well aligned.

Most of all, sweat floods the eyes and falls on the vase.

The respirator was once snow white:

I glue the bottom. To speed up the process, I use my weight with dumbbells in my hands as a press ... The vase can withstand more than 100 kg without squeaking, despite its lightness and thin walls. Now I think, what would have happened if the vase had scattered?

Description plywood vase drawings

Drawing of crafts Small vase for cookies - Vase made of plywood in the form of a sports cup drawings and tips. Vases Plywood products cutting with a jigsaw The difficulty in choosing plywood is located in: Interior items, Drawings. At the root, the approach and structure of the vase has been changed. For cutting, you need to have a piece of plywood drawings. For work you will need: a jigsaw, saws, saws for sawing Cutting out a vase from plywood. The site contains a collection of product drawings, photos of works. Interesting ideas and cutting drawings. To make a vase, you need a little plywood sheet We give you the drawings of all. Now do-it-yourself plywood crafts. Diy ladder made of plywood drawings. Glass vases hold cupids and voluptuous. The site contains a collection of product drawings, photos of works. DIY plywood box: manufacturing. Drawings for cutting out caskets, animals with a jigsaw from plywood: video - memo. Or you can have a full drawing of a vase in jpg format. On plywood trimming Literature on jigsaw sawing out of plywood. Out of four existing types plywood is suitable only for the first, at least the second. Homemade fruit vase made of wood, handmade master class, drawings. Most of the books contain sketches and drawings for cutting with detailed description... Plywood vases drawings Plywood vases drawings Plywood vases drawings Plywood vases drawings Cutting out of plywood with a jigsaw. The video shows the technique and the assembly process. Drawings, pictures and descriptions of plywood chandeliers, sconces and lamps. Drawings, pictures and descriptions of plywood products for sawing. The jigsaw gives you the chance to make various internal holes. On this page you will find homemade drawings and drawings. Thickness of plywood A large selection of books and magazines on cutting with a jigsaw from plywood. DIY plywood crafts with a jigsaw drawings. Cutting from plywood with a jigsaw: a set of tools, material, drawings and cutting technology Image result for plywood crafts drawings. Sami Prefab Cabin Wooden Projects Vases. Drawings, pictures and descriptions of plywood products and homemade products. A similar drawing of this work is presented in the section drawings; boxes, plywood vases, corners. Drawings of Jigsaw Boxes From Plywood Download Free. Cutting with a jigsaw from plywood drawings Cutting with a jigsaw from. Drawings collected the largest collection of drawings for cutting out of plywood. 1 Free jigsaw drawings and much more can be found exclusively at saw - man. Designed for the execution of a 4mm plywood vase and a drawing for 6mm. Literature on plywood jigsaw sawing. A selection of material on the topic plywood box drawings dxf. User posts Art cutting jigsaw. Drawings, pictures and descriptions of plywood products.

How to make an artistic plywood vase with your own hands

Any DIY crafts perform "four tasks". The first is a great free time, you can take a break from everyday annoying problems. The second - as a result of such "rest" beautiful products appear in the house. for various purposes, from small souvenirs to exclusive unique furniture. Third. Artistic cutting is a great way to teach a child to work, it is a kind of trouble-free parenting method. Your child will always be happy to spend time with his father for "adult and useful activities." Fourth, by making products with your own hands, you increase your authority in the eyes of everyone around you. And in their own, of course, which is also pretty nice. In this article, we offer you drawings of a vase with dragons in chinese style... She is able not only to diversify any festive table, but also become its main decoration. What do you need to have for manufacturing?

Artistic Cutting Tool Set

We consider it necessary to list all the tools and accessories that you will need to get the job done.

Jigsaw. Previously, only hand models jigsaws. It was rather difficult to work with them; one product, depending on the complexity, could take several weeks. Now in the implementation there are quite a few different jigsaw models with electric drive... Such special tools not only increase labor productivity tenfold, but also improve the quality of the cut, which is very important for the final look of the product.
An eclectic drill with a fine drill bit. With its help, "starting and technological" holes in the plywood are sawn. In some patterns of the same type, using a set of drills of different diameters, you can make turns of lines or round through holes.
Plywood sanding tools. The set should include abrasive skins of various numbers, files, files, stone blocks.
A set of devices for transferring a drawing to plywood. You need to have tracing paper, pencils, knives, rulers and compasses.

That's all, the list takes up a lot of space, but most of their necessary items and tools are already in almost every home.

Transfer picture

To make a vase, take polished plywood with a thickness of 3 ÷ 4 millimeters, in addition to it, you will need high-quality transparent wood glue and transparent varnish or paints.

The drawings given by us need to be printed on a printer, select the scale you need. Then there are two ways to work with pictures.

Using tracing paper and a pencil, carefully transfer all the lines from the print to the plywood. This is a rather difficult and tedious business, it requires great care, there are often various mistakes that can be noticed already during cutting. It can be difficult to correct such errors, sometimes it is simply impossible and you have to start all over again. And this is very, very unpleasant, instead of calming nervous system she is additionally "excited".
Not translate anything at all, but cut out immediately. To do this, you need to print as many drawings as there are elements of the product, this is easy to do. After that, we cut out a drawing of each part already in the scale we need and using double-sided tape or glue we fix it on plywood. We cut out the detail immediately according to the paper drawing. Simple, reliable, precise and fast. In short, what we all like. Our fathers and grandfathers could not use this method for one reason - they managed to get only one sheet of paper on which there were drawings of all individual elements in the singular.

You can go one more way. From our drawing, take only the principle of connecting individual parts into a single structure and dimensions, and make the ornaments yourself. This is not as difficult as you might think. Take a piece of plain paper, fold it several times and cut holes in the places of bends with scissors. In this way, our ancestors made on christmas tree paper snowflakes. Make several variants of patterns, among them choose the most successful one and use tracing paper to transfer it to plywood. The first cut out element will be a template, with its help it is easy to draw a contour on all other parts.

Side parts

How to cut out blanks for a vase

We will tell you how to cut out a vase on a stationary electric jigsaw... The technology of manual sawing is not much different, so we will not talk about it separately.

Before starting sawing, you need to drill small holes in each "blind" section of the ornament, the diameter of the hole should ensure the smooth entry of the nail file.
Plywood should be led along the lines smoothly, do not make sudden jerks and it is highly desirable not to stop. We strongly recommend that you check the cut quality of plywood, because a lot depends on its type and your professional skills.
The file should always be in an upright position, do not bend or twist it.
If you need to make a very sharp turn of the file, then it is better to wash it down in several stages. Rotate it a few times, almost idle, and thus cut the sharp turns of the pattern.
Always start cutting from the middle of the pattern, this will eliminate the risk of plywood cracking in very thin places around the edges. Plywood cracking is always an unpleasant phenomenon, and in some cases you have to redo the part. This applies to those situations when in these places it is necessary to connect several parts into one structure.
Work in good lighting; during work, nothing should interfere with the free movement of plywood and move yourself.

Assembling the vase

Before assembly, you need to carefully grind all the cut points. Where possible - use sandpaper, where not - work with flat or round files. The surfaces must be coated with two layers of varnish, varnishing should be done the usual way in compliance with technology. Almost all connections are made according to the tenon-groove principle, the dimensions of the tenons and grooves should be chosen taking into account the thickness of the plywood, the tenon must enter the groove with little effort, the height of the tenon must be exactly equal to the thickness of the plywood. The same rule applies to parts that are connected to the lock. Be sure to use transparent wood glue.

Finished vase

4,000 rubles

RUB 2,000 RUB 2,200

1 450 rub

700 rbl

1 650 rub

1 400 rub

1 350 rub

1 100 rub

RUB 3,000

1 100 rub

900 rbl

1,500 rubles

Plywood is very affordable, relatively inexpensive material for various crafts. Things made from it can have more than decorative value but also to be useful in our Everyday life, at home.

Plywood is an easily processed building material, which is produced by gluing several layers of veneer, specially processed wood chips.

Introduction

These sheets, which can be used for making crafts and structures, may differ:

the number of veneer layers - three-layer, five-layer and multi-layer;
the type of wood from which the multilayer sheet is made (deciduous or coniferous);
according to the degree of processing (sanded on one or both sides, not sanded).

Building codes and standards

To find out more about this building material(on the classification of the entire plywood nomenclature, grade, standard sizes produced), which can be purchased for the manufacture of many products and crafts, it is recommended that you familiarize yourself with the following documents:

GOST 3916.1-96 "Plywood general purpose with outer layers of hardwood veneer ”.
GOST 3916.2-96 "General purpose plywood with outer layers of coniferous veneer".

Schemes, drawings and patterns for products from plywood sheets

Drawing programs for computers

Today, you can easily find a diagram, a pattern for a plywood structure, so that later, using computer-aided design systems, you can prepare any drawing (including the above pattern of a cat). Then, using a plotter, print on a paper sheet of the required format.

Drawing popular programs are the easiest to learn and can be used in 2D and 3D modeling, including for plywood structures:

"KOMPAS" - complex automated systems, with the possibility of drawing up drawings, according to the standards of the ESKDi SPDS series;
AutoCAD is a two- and three-dimensional computer-aided design and drafting system.

So, if you cannot find a detailed drawing of the product you need made of plywood material, then the applied possibilities of the given software will help you make a full-fledged drawing according to any schemes and patterns posted on the Internet.

Kayak

The price of construction plywood from which the kayak is made is simply incomparable with the pleasure that a person who made it with his own hands, who loves water trips on row boats, will receive.

A kayak by the Eskimos, this is the same kayak by the Aleuts - a traditional rowing boat of the peoples of the Arctic. Such a boat can be single, double or triple. Let's lay out the drawings of the kayak made of plywood for one person.

The algorithm for building a rowing boat from plywood sheets is, in principle, general, with the exception of some nuances. Step by step order the steps for cutting, processing and assembling the kayak can be viewed in the video in this article.

Plywood table - simple and functional

Do-it-yourself clear drawings of a plywood table, which will be easy to implement even for a person, without special carpentry skills and experience. Table cover (1 sheet) - 1300 x 600 x 16 (mm) Inner wall (1 sheet) - 1170 x 400 x 16 (mm)

Plywood constructor

Various plywood constructor drawings are now gaining more and more popularity. Assembling such models from safe material is a very useful activity for children and adolescents. Such crafts will become good examples of collections, decorate the corner of modellers.

Tank

The stages of installation of the tank model are as follows:

Plywood is sanded (first with medium-grained and then with fine-grained sandpaper);
Drawings are accurately transferred through a carbon copy onto sheet plywood material sanded with fine-grained abrasive.
In the corners of the contour translation, through holes are drilled with a drill (drill 3 mm or more);
Fasten the saw in the jigsaw and start cutting out the elements of the tank;

Note!
Cutting out the parts must begin inside the contours of the tank blanks, and only then along the office itself.

Advice!
When assembling the plywood assemblies, keep the model handy Various types files to fit the elements to each other at any time.

After adjusting all the parts, you can start gluing them (for example, with PVA glue, "Titan");

Advice!
To make the knots and elements of the tank more firmly and reliably grabbed with each other, you can tie them with thread or rope for a while after gluing them.

The cannon can be made by cutting wooden handle brushes for watercolor paint or other auxiliary material;
If desired, a side number or other inscriptions and patterns can be applied to the tank, or to any other model;
For greater safety and decoration of the model, they can be coated with varnishes and paints.

Retro car (old Mercedes)

Note!
When you transfer these drawings of a car from plywood with your own hands to the plywood sheets themselves, do not forget to transfer the numbers as well.

When assembling the model itself, carefully look at the numbers.

In this case, the process is carried out according to the following algorithm, in accordance with the digital designations:

part or node number 1 must be connected to another number 1;
and the part under number 2 is attached accordingly with the next number 2, and so on, until the machine is assembled.

Gun

Drawings of a bulldog model plywood pistol. When assembling, we follow the same rules as when assembling a machine: the same numbers must be mounted with each other.

Advice!
It is better to cover this pistol model from a spray paint bottle; layers of black paint can be applied to better resemble the original.

Dinosaur

Drawings of dinosaurs made of plywood, for example, those presented below, can be executed in any desired scale when designing according to the pattern presented in the drawing program for a computer.

The preparation of the material, the elements of the model and the assembly itself is not difficult, but you have to be patient when working with a jigsaw and fitting the nodes of the model to each other.

Napkin holder - "Grape leaves"

This grape leaf shaped item will always come in handy in household for its intended purpose - for napkins, and for storing, for example, sheets of paper of the selected format:

Vase, pencil holder, pens, brushes

Drawings of a plywood vase, according to which you can easily cut out a craft of the size you need:

Plywood panel

It is the ease and simplicity of cutting with a jigsaw from plywood sheets of various configurations with different sizes, assembly of them various designs, allows you to perform various decorative panels for the walls of our home. Any carefully executed panel is a great gift to family and friends.

Drawings of a plywood panel, which also serves as a shelf in the household:

Some useful tips and warnings:

When transferring patterns, drawings to plywood, use the thinnest and sharpest pencil lead. It is even better to use a used ballpoint pen, then the lines will always be the same, and the carbon paper from the ball will not tear. It is convenient to transfer drawings to plywood using a laser printer.
For better fastening parts, where possible, it is recommended that the width of the grooves correspond.
There are two types of files with large and small teeth. It is more convenient for beginners to learn how to use a thick file, and cut out a thin one small parts already having some experience and skills in using a jigsaw.
The saws should be cut from top to bottom, so pay particular attention to correct fastening saws in a jigsaw.
Saws can break easily, so cut carefully, do not let the parts hang on the saw blade.
When purchasing a file, make sure that the teeth are sharp, and it itself should not bend easily, but, on the contrary, should be firm. Convenient in work are not flat, but the so-called "twisted files" - they can be used to cut in any direction.
For those who have a hobby of cutting out structures from plywood sheets, there is no need to purchase band saw, it is enough to purchase a jigsaw. Although everything is not for everybody, some masters still often resort to hand jigsaw when "you need to feel the material."

conclusions

Before choosing, purchasing and directly working with the material from which you will cut models, panels, designers and structures, familiarize yourself with its types, classification according to construction documents (GOST).
For cutting, purchase a quality tool, equipment and accessories for it.
Choose quality plywood responsibly. Do not limit yourself to visual inspection, tap it for internal voids and delamination due to poor adhesion of veneer layers.
Before working with a jigsaw, optimally equip your workplace. Special attention give it good lighting so that the cut is clearly visible, the marking and the eyes do not get tired. It is not bad to use a stroboscope to illuminate the place of work with a jigsaw. Convenient and comfortable sawing!

If your new hobby is sawing a variety of decorative elements, burning or wood carving, then our advice would be to start with a material such as plywood.

There are several significant reasons for this at once:

Plywood is easy enough to work with.

If you have in your hands good tool, and you start with small figures, it will only take you a couple of hours to make them.

The material is versatile in use, so you can make literally anything you want from it: furniture, toys, small decorative elements.

All this can be a great addition to your home interior.

Features of working with material

What is a plywood sheet. It consists of several veneer sheets at once, which are connected to each other with glue.

Important: plywood can be different types: based on beech, birch, pine.

Not only quality depends on which sheet you choose finished product but even its structure and color.

If you are going to cut out various figures with a jigsaw, then you need to choose the highest quality types of plywood.

They are particularly durable, which ensures that the plywood does not crack, ruining the entire appearance products at the most unpredictable moment.

If you are going to start work immediately, immediately on the day of purchase, then choose only dry sheets of wood.

They will not break the jigsaw file every 10 minutes.

To work with plywood, you will need to acquire a number of tools.

Basically, they are constantly the same for all types of products, so that only a one-time investment is required:

Jigsaw
Jigsaw blades
Hand or electric drill
Ruler
Grinding machine
Scorcher.

Framework

If you want to beautifully decorate your home or present an original gift to someone close to you, make a plywood frame with your own hands.

The preparation process will not take you much time, because you just need to get the necessary materials.

Note!

They are standard for all cases, and we have already mentioned them earlier.

We will offer you master classes on light plywood crafts. You can make either a regular straight frame or cut various patterns and figures on it.

First you need to make a template, and after that you can cut it out, trace the contours with a pencil on plywood and start the manufacturing process.

This stage is not only the most responsible, but also the most exciting. If you put a piece of your soul into the work, everything will definitely work out. Finished construction must be varnished. Ready!

Doll furniture

This task will be a real test for parents.

Note!

The so-called test of the acquired design skills.

Feature of creation doll furniture is that children absolutely do not tolerate falsehood.

If they see that the furniture has not been worked out in detail, but instead kitchen stove for your favorite doll you brought an ordinary rectangular bar, then you simply cannot avoid serious grievances and childhood disappointments.

The second feature of making such a plywood craft using a jigsaw is that all this furniture must be carefully worked out sandpaper or a sander.

Your child will constantly be in contact with these self-made toys, and in the case of poorly processed edges, he may get injured.

Note!

Well last feature crafts from plywood and at home is that the materials for such furniture should be absolutely non-toxic and normal for constant contact with the child, because he can drag it into his mouth or take it to bed with him.

This is not a simple applique or paper craft, so you need to take the matter seriously, following a whole list of actions to be performed.