Perhaps, all summer residents know that it is easy to do without a shower on the plot. Especially relevant in summer timewhen, after a whole day of work on the beds, take water treatments It is simply necessary for hygiene reasons.

Collect summer souls easily, and the manufacturer's options exists a great set. On some aspects of work and will be discussed.

Screen

As a temporary solution, you can make the simplest shower: on some elevation, fasten the metal or plastic tank, preferably dark color, with a crane and mixer, make a screen. Everything about everything will go away the minimum amount of materials, time and labor, so such a design can be erected in a few minutes.

Polycarbonate shower

Stages of work:

• First, they align the place on which construction is expected.
• Then you need to place a place. A wooden peg is driven into the ground. Then, at a distance of about two meters from it, the next and between them stretches the cord.
• Similarly, two more kids are riding and connect them, so that the square is. To check the correctness of the markup compare the diagonals, they must coincide.
• In places of marking angles, it is necessary to dull pits with a depth of about 1 meter.
• These pits are installed wooden or metal poles. It is important to remember that the part of the pillar, which will be below the level of the Earth should be treated with waterproofing materials, for example, wrapped in rubberoid. As a seal, which is necessary for durable pillance in the ground, you can use a brick battle or concrete if we are talking about a metal frame.
• Then you need to do the cutting of the design. At a distance near the meter, each other is nailed or screwed by the scores of the board or metal pipes are welded. Such an idres must be made throughout the area of \u200b\u200bthe walls. Where there will be the door, the crate does not do.
• Then polycarbonate sheets are mounted on the walls. The sheet is cut into size and is screwed by self-drawing.
• The next stage of construction is the installation of a roof. As a roofing material, you can use, for example, a simple slate. Pre-laid and fix several horizontal bars that will perform functions rafter system. They are stacked and the slate sheets are fixed. It should be borne in mind that with one of the parties under the carrier bar, you should put small lumps in order to provide an angle of inclination required for the flow of precipitation.
• Next, the water tank is installed. At the place of its installation, you must additionally strengthen overlaps. The tank can be made, in principle, from any material, but the plastic should be preferred. Such a tank will be much easier than metal, which is important.
• And finally, the final stage is the installation of the door: suitable in size wooden frame Sheets with polycarbonate and mounted on loops.

As a floor, a simple tray can be used, which is a grid made of wooden bar.

Shower cabin on metallic frame

For the manufacture of a shower cabin can use a metal corner.

• First welds the frame. Its dimensions are chosen arbitrarily, but the height of the structure should be at least 2 meters.
• After the frame will be made and installed, the water tank is mounted upward, and an opaque film stretched between supports will serve as the walls.

In order to take a shower to one person, it will take at least 20 liters of water, which means that even the smallest water tank should have a capacity of about 50 liters. It follows that the place of installation of this tank should be well strengthened.

Video: Construction of a summer soul on a metal frame with a barrel on 220 l

Among the materials, it is possible to mention and become the usual metal profile. As in the previous case, the framework is collected, and then it is trimmed with this material. In principle, this version of attention deserves, but from the practical side, the metal is not the best choice.

In the soul there will be constant contact with water, which means that, as it were, a well-profile sheet is covered protective compositionsCorrosion will start quickly enough.

Again, as a temporary measure, you can solve a question for an ambulance hand. In the presence of all necessary for the construction of materials, this design is collected literally in a few hours. But, perhaps, this is one of its few advantages.

Video: Summer Soul Design from Metal Poll

Heated

This option is good in all indicators, as it allows you to use the shower with any weather, however, its device is somewhat more complicated and requires large knowledge and skills.

You can add that one of of most important conditions The work of such a soul is the device for reliable thermal insulation. The most suitable for this material can be called polystyrene foam. It is racks to moisture and easy to install. And if it is also covered with a dense film, then it will be almost a hermetic room, which will be relatively warm in itself.

To accelerate the heating of water in the tank it can be painted in black.

If a heated system is used, it can be additionally equipped with an automatic water set than even more easier life, but all these technical devices Learn additional financial investments.

Photo

Blueprints

Shower cabins for cottages - one of those "facilities", which are easy to do on their own, and it is very difficult to do without them. There is a huge number of different options for shower cabins, each master contributes to their design its improved ya. We will not dwell on complex and expensive versions, Consider the most "budget", but very functional solutions.

Before starting construction, decide what you want to have in the end, what capabilities and characteristics should have a shower. Specific features of the shower cub depend on:

• the number of people living in the country. This indicator affects the volume of water heating and the need for a drainage device;
• landscape features cottage plot and physical characteristics Soils. Showers are better installed on small elevations, it will allow in most cases to do without a special drainage. The installation site of the shower must be the solar, is not very far from the cottage. It is desirable that in this place were garden tracks. Another important moment - The presence of water. If you have any automatic water supply system - excellent, we will tell how to make automatic tank filling. If the water in the country is obtained by buckets of the well - the tank on the shower cabin will be filled manually;
• manufacturing materials. The frame can be made from the shaped rolled, square pipe or wood. Each material has its own characteristics. Walls are truncated, cellular polycarbonate or metal profile. There are cheaper options - to tighten the tarpaulin, opaque polyethylene film or ordinary dense matter;
• location location. Cabin can be separate or attached to outdoor wall cottage house. There are variants of a mobile cabin - if necessary, it is transferred to a new place, does not require the construction of foundations. For such options, ultralight are chosen bearing structures and materials of the trim;
• engineering features of a tank for heating water and a soul drainage system.

Street showers from Gabion
Street souls

Street shower of bricks (stone)
Big Wood Street Shower

On the size of the cabin it is not worth "save", make it in a height of at least 2.2 meters, the size of the base is at least 1 × 1 m. The fact is that the cabin should have a place for bath accessories and clothes. Consider step by step two options for cabins - with a metal and wooden frame.

Shower cabin with metal frame

Metal shower Shower cabin with metal frame
Shower cabin do it yourself at the cottage photo

For the production of work, you will need square pipes with a cross section of at least 20 × 30 mm, sheet iron with a thickness of 1 mm and a 45 × 45 mm corner. Tools - angular grinding machine (Bulgarian) and welding machine.

GOST 8639 82 Steel Square Pipes
Iron leaf galvanized
Corner 45 x 45

Step 1. Draw a sketch of the booth.

The height of the cabin is about 2.2 meters, the size of the perimeter is 1 × 1 m.

For rigidity, refer to three rows of jumpers: at the top, in the middle and below. For the lower jumpers, it is better to use the corner, a wooden grille will be installed on its shelves. At the top, it is necessary to make stops for placing the water capacity, the specific dimensions of the stops depend on the size of the container.

Side surface can be sewed with a metal profile, a cellular polycarbonate, plastic or wooden clapboard or trimmed with various flexible materials. Under each material you need to think over the place for fastening. Drill mounting holes in square trumpet. It is impossible to make metal plates for these purposes.

Do not be too fascinated by cellular polycarbonate for the trim. It is good for many indicators, but only a limited time. One of the disadvantages that manufacturers never mention have never mentioned - moss will begin to grow in cells. And no compactors will help, the power of nature will overcome any protective measures. The type of leaf polycarbonate with moss inside you will not please and this is mildly. We generally advise showers cover light and cheap soft materials. You can change them every season to new, the cabin will always have an attractive view without a lot of time and finance loss.

Step 2.

If you already have an idea of \u200b\u200bthe frame of the frame, you can start it.

Start working from cutting metal elements. Cut 4 2.2 meters long tubes (vertical supports). If you wish to do open doors in the booth, you will need to cut off two more pieces of pipes, the length can already be smaller, the size of the door height is enough to withstand within 1.5 m.

Under the focus of the grille, you will need four corners one meter. The same length you need to prepare pipes for jumpers of side surfaces and doors. They will be required by two for each element of the cabin. You need to cut the details only by the template, all the angles are strictly 90 °.

It is very important: follow the safety regulations while working with grinding machineInjuries can be very heavy. Some "crafts" establish cutting discs In this way, that the sparks during work flew in the opposite direction from them. This is a gross mistake! In this position, the Bulgarian undermines with a huge effort, to keep the tool in his hands is impossible.

Step 3..

Check the sections of the sections and read them for welding. The champecker can not do, the strength of the welding seam and so it will endure the load.

Step 4..

To increase the strength of the structure, harvest metallic equilateral corners, the length of cathets is 5 ÷ 10 centimeters. Set them preferably at all corners of the frame and doors. Under the feet you need to weld the square stops ≈20 × 20 cm.

Triangles to enhance the design

Step 5.

Welding frame. Works are very careful, never immediately lift the full seam on one side. During the cooling, it will pull the metal, return its original position will be very difficult. Initially, the contiguous pipes on the one hand, fir the design and only after that you can put a complete seam with the opposite. Sow cooled - brew the place where you have naked.

For welding, you can use Ø4 mm alternating voltage electrodes.

This is the most universal diameter of the electrodes, you can cook metal with a thickness of 1 ÷ 4 mm. Correct the current strength, the metal must melt under the electrode on the desired depth, but do not cut through the pipe wall completely. If you do not have experience welding work - Better contact for help to a professional. This eventually costs cheaper than to translate expensive material in marriage itself.

Works need to be performed on a flat platform, constantly monitor the corners of the structure. The frame will stand on metal plates-legs of approximately 20 × 20 centimeter in. Prepare them and breed.

Step 6.

Build frame. Alone, these works do not do, you need to call an assistant. Welcome separate framework elements in the specified way, constantly check its spatial position. In the lower part, the corners are welded on which a wooden grille will lie, make a design for water tank top.

Summer shower at the cottage - frame

Step 7.

Finish finish. Carefully remove the grinding machine all sowers and sharp cornersClean metal structures from rust, oil and dirt.

Remove welded Sow. At this stage, you can stop or continue processing for better results.

For staining, use special paints for metal. It is necessary to dye at least twice, the metal will be viewed after the first time. Do not use pneumatic spray gun, it is suitable only for painting large surfaces. In your case, most paints "leave" in the air. Krable only with a tassel, you will not need more than one to two hours.

In the photo - Anticorrosive Metal Forms

Next, you can make wooden grids under the feet and start using water tank. How to install the container and connect the shower we will tell at the end of the article after describing the manufacture of a wooden frame of the shower cabin.

Video - Summer shower on the plot with their own hands

Shower cabin with wooden frame

Linear dimensions may be the same as in the variant with a metal frame. Manufacturing material - wooden bars 50 × 50 mm, 50 × 100 mm boards, select specific sizes, taking into account the total weight of the water capacity. Boards and bars need to be skipped through a flight - levels size and grinding roughness.

Step 1. Draw a sketch. It will come in handy not only during work, it is much easier to choose optimal option Designs. Better to correct your mistakes on paper than on ready product. Draw on paper a few options, think over the location of the stops, shelves and tanks for the container. Compare several sketches of shower cabins and select the most suitable for yourself.

Step 2. In size, cut all blanks for the frame, according to the scheme it is not different from the metal. Once again, pay attention - follow the dimensions, make the workpiece only in templates.

Step 3. On the flat site, start collecting individual structural elements. The connection is better to do in Polterev. If it is difficult for you - use metal plates and corners on self-drawing.

Step 4. Collect individual framework elements into a single design. If there are doors - strengthen them on the loop.

Instead of doors, you can make an ordinary curtain. Provide a water tank installation location.

Attach the shelf for bath accessories and hooks for towels and clothing from the inside. Prepare a wooden lattice for the legs.

Wooden grille - example

Step 5. The ends of the vertical racks need to be protected from rotting. You can process them with special antiseptics, and can be soaked with olifa or sunflower oil several times. By the way, the olifa is a crude oilseed oil, including sunflower.

Let's give a few practical Soviets on the device of the shower.

Foundation

You can meet the tips to put shower cabins on the screw foundation, pour under them a concrete site, etc. Do not advise you to engage in such works for several reasons.

1. First, the shower cabin is not the structure for which special foundations are required.
2. Secondly, we can guarantee that over time you will have a desire to build a warm shower, and for this you have to dismantle the booth.

Under the foundation we advise to use paving slab or a wide blocking. Remove with a small layer of the Earth under them, align the tile on the prepared places along the horizon. Match it a little - it will eliminate the appearance of the distillation during the use of the Cabin.

Video - Rules for laying paving slabs

Water removal

And here you can find tips on the device whole engineering system. What does practice show? The volume of water tank rarely allows you to simultaneously take shower more than two people, the flow rate for each approximately 20 ÷ 30 liters. Water heating time depending on the weather ranges from five hours. We assure you that during this time the water used will calmly go to the ground. And yet - do not fear that without a sump "will appear unpleasant odors"This is not sewage.

Capacity for water and shower

You can build the most beautiful and most reliable shower room, but it will be very uncomfortable in it. Cause - Incorrect installation of water and shower tank. How to avoid such trouble? Let's give several practical recommendations.

Water tank. You can use two options: plastic and metal.

Plastic containers

Advantages: relatively low price, wide selection In terms of capacity, ease of installation.

But there are significant disadvantages.

1. Firstly, to increase the efficiency of heating, it is recommended to use plastic black tanks, and this option is difficult to find and, even more so, to choose the optimal option in terms of capacity. Repaint the white capacitance into black is almost impossible.
2. Secondly, the physical indicators of the strength of plastic do not allow reliably to fix the place of connecting the shower. Permanent oscillations of the output nozzle breaks the tightness of the connection, leaks appear. In addition, due to frequent bending efforts, the effect of material fatigue is manifested in these places. And this can lead to a complete separation of the soul with all the consequences.

Metal containers

Advantages - High Metal Strength Guarantees the tightness and reliability of the shower attachment. Metal is easy to paint black, and such a color significantly increases water heating efficiency sunny rays.

Disadvantages - increase weight. You can not pay attention to corrosion processes, a thick-walled barrel will stand decades. Especially since the water barrel is corrosive much slower than empty. We advise you to use metal barrels: cheap and secure.

Arrangement and operation

Another important question is how to fill with water tanks. Pump buckets - not the most the best way. We strongly advise you to take all measures to fill the water with a hose. If you have a well or well located at a great distance from the booth, you can make a temporary line of a flexible gender from the cottage. We will also tell you how to make water in automatic. To do this, you can use an ordinary float from the drain tank toilet bowl. Adjust it to the difference of triggering about twenty liters of water, taking into account the size of the container. It will make it possible to constantly maintain the full "refueling" of the barrels, the water will constantly heat up, you do not have to finish the process of receiving the soul due to the lack of water. Another plus "automation" - the likelihood of water overflow is eliminated. The mooring of the soil near the shower cabin is undesirable.

You can find a proposal for the shower water to select from the container using the float. The end of the flexible intake hose is fixed on the float (you can take a piece of foam of the corresponding sizes), as the water is spent, the float will be descended, the fence is always made from the top, warm, layer. Such a device gives effect, but it is insignificant. The fact is that water in tanks is heated from the walls, hot climbs up, cold drops down. The movement of water in volume is almost constant, which means that there is a big difference in the water temperature in the tank depending on the height.

Another enhanced is to make electric heating, which will allow warm water Regardless of weather conditions. Yes, water will be hot, but only who will die take a shower if on the street low temperature? But this is not all problems. During the electrical heating device, PUE rules should be strictly observed, and they make very stringent requirements for such work. In addition, it will be necessary to install the power on / off automatics. Do you need such "difficulties" in an ordinary shower in the street? If there is a need to use the shower in the cold time - do the shower in the cottage. This decision will have to be taken in the event of a long stay at the site.

If your shower is attached directly to the tank (there is no shower hose), then a complex of additional measures to its reliable fixation should be taken. With the help of stops (wooden or metal), secure the nozzle, exclude even the theoretical probability of oscillations during the use of the tap. The crane is better to install a valve type. It has a much easier rod running, the water pressure is gradually adjustable, the working surfaces are not oxidized - the smoothness of the stroke does not change over time.

During the construction of the shower cabin, provide an extension of small additional rooms. They can be used both under the expansion of a shower or a device near her one more and for a separate locker room.

Industrial showers

A wide selection of both the price and operational characteristics allows you to choose the optimal option, taking into account your own preferences and individual features cottage plot. Industrial showers can be completely plastic, metal with trim various materials or awned. Completed with water tanks, cabins (metal or wooden), pallets and material of the trim.

Shower for giving plastic

According to consumer reviews, it is quite convenient to use the cabins, but there are several significant drawbacks. Plastic cabins do not meet the required indicators of strength, if children are present in the country, the season of work without repairing such a design will be great.

The second drawback is a high price. A shower cabin made by hand will cost an order cheaper. There are quite cheap options for industrial cabins, but in terms of strength indicators, they can be attributed to the category of "single-room". You should not throw money, you can independently build a wonderful, solid and reliable shower room for this money.

Street shower "Economy"

The third drawback - mass production is calculated for the average user. This is natural, all manufacturing enterprises work according to such a scheme. By creating a booth with your own hands, you can do all the calculations for yourself, change the location of the soul, its height, dimer drain holes, adjustment mechanisms, etc. Also, there are no restrictions on installing additional equipment, change in height and width, devices of additional decor elements. There are masters manufacturing very original showers.

Video - Cabin Cabin Tentified

Conclusion

Everyone country plot Requires constant improvement, do these affairs. You can start with the shower cabin, then build a gazebo, then the bath and so on, from simple to complex. You will make sure personal experience - not better than thatWhat is done with your own hands.

I have already told earlier. You can get acquainted with the materials according to the links that I led. Today we consider moments finishing work With a solid shower class cabin.

The house for the shower is desirable to arrange in a single style with the rest of the buildings. If you have a wooden shower, any material is suitable for upholstery outside: OSB, plastic or wooden lining, moisture-proof plywood ...

In the picture above the simple version of the wooden cabin, without insulation. Just summer shower. If you want to insulate the walls, then you can take polystyrene foam - they are filled with all the cavities of the frame. Next, the polystyrene gasket is inhabited by polyethylene film applying construction stapler. On top of the film you need to perform an internal finish.

Can be separated interior Dacha shower with plastic panels, which are pretty comfortable in operation. They will reliably protect the wooden frame from rotting. Modern materials Have excellent water repellent properties.

Sample Open Summer Soul

This shower was photographed by me in one of the spa resorts of Thailand. As you can see, it is pretty simple - a concrete base, which is fenced with bamboo tubes.

Behind the absence of a freely growing bamboo in our latitudes, you can make the walls from branches or subtle trunks of wild trees - willow, an instance, etc.

The floor is decorated with a mosaic of glass balls and multicolored pebbles. All this lacks only a motley curtain.

From the inside the tree is better not to paint

How to glue tile in the shower

In a solid soul with brick walls, the cabin can be postponed tile. Working with a cafeter requires certain skills. The tile must be put up to the level of human growth. It was then that the upper bound between the tile and the wall will be less subjected to the destructive effects of moisture.

The tile is glued to the wall using a special tile glue, you can put a tile on cement mortar. Before masonry, the tile glue is divorced by water in the proportion indicated on the label. All the volume of glue is not recommended immediately, it is better to do it as the tile sticks.

Start laying the tile from the bottom of the wall. To prepare the solution, mix one part of the grade M 5 cement and four parts of pure sashed sand. Water should add so much to obtain a consistency of thick sour cream.

Stages of work when applying the solution and glue are the same. Using a gear spatula, apply the adhesive composition on the tile, and then tightly press the tile to the wall surface.

At hand, all the time should be a soft rack to immediately remove the surplus or glue, which will perform from under the tiles. If you work carefully, the tile will lay down with smooth rows.

The remaining tile can withtreate concrete or brick floor of the shower cabin. When lays out of the floor, it should be made of high thresholds between the separation for washing and the locker room, in order to get there water.

When you are facing the walls with a tile, you can hang in the cabin of the shelf for shower accessories, as well as install a bar for a waterproof curtain, which will separate the washing separation from the changing room. In the locker room you should strengthen the hooks for clothes and a mirror.

RESULTS

Of course, not all do not all make a full tiled shower in the country, so these recommendations can be applied in the apartment. And for the cottage to build something easier. After all, it is possible to rinse in the most simple structures with four walls and a tank on top.

Staying in the country's hot summer will deliver genuine pleasure only if you can enjoy the cool summer soul at any moment.

Of course, today trade offers literally everything, including portable optionbut ensure comfort on panstoneBy building a summer shower for giving with your own hands, easy. It is only necessary to know the foundations of its device and follow the rules for its creation.

The easiest way to get a beautiful lawn in front of the house

You, of course, saw the perfect lawn in the cinema, on the Alley, and perhaps on the neighboring lawn. Those who at least once tried to grow a green platform in their own area, without doubt they will say that this is a huge work. Lawn requires careful landing, care, fertilizer, watering. However, only inexperienced gardeners think so, professionals have long known about the innovative agent - liquid lawn Aquagrazz.

Shower installation is one of the most simple country buildings, which necessarily requires the thinking of water supply and drainage.

The standard option is a rectangular room having 3 closed sides and the front door.

Before building, it is necessary to determine which option is the most appropriate. Owners dacha plots can use for its erection different materials. Often, the country's souls arrange as frame structure. In this case, durable side walls are not provided, replacing with light, closing upstander. No less relevant are more capital buildings with brick or folded walls.

Today the following options have become the most popular for summer residents:

• from wood;
• from polycarbonate;
• from professional flooring;
• from utility materials;
• from brick.

We will get acquain your details with different options.

Preparatory stage

Holding the shower at the cottage, first of all, we define a comfortable place for it. Preferably choose open placeallowing to air and dry, best - having some elevation over the others. Most use water heated naturally - solar rays. That is why the shady space is not the best option.

Thinking up the design, you should not be limited to the soul area, it is necessary to provide a place to disguise.

The most convenient for planning the construction are the following dimensions:

• width - 140 cm;
• length - 190 cm;
• height - from 200 to 300 cm.

Preparatory work includes not only the creation of a scheme, but also preparation of the pit for wastewater. This will allow you to collect soap water, without allowing its spreading on the site. The waste pit may be approximately such dimensions: length and width - 100 cm, depth - 40 cm. The bottom of the pit is recommended to fall asleep with rubbank.

With frequent use of the soul large quantity People arrange special drain pitwhich connects pipes for water flow covered under the inclination of 3-5 degrees. Optimal distance to such a pit - from 5 to 8 m.

From wood

To build a shower of wood, it is necessary to prepare a base of 1x1 m, consolidate four side beams or a bar to it and decide them.

Frame beams must be durable, so we choose the timing of 10x10 cm for them. The frame racks should be strengthened with the help of corner splines.

You can install the shower in different ways. Frame racks can be strengthened in the ground. At the same time, the edges of the timber are protected from rotting using machine oil or bitumen, wrapped with rubberoid in 2 layers, placed in the dumped pits and concrete.

You can also make concrete supports as a foundation. In these supports, which are 20-30 cm above the surface, fasten frame bars.

Another framework - metal pipes.

Attention should be paid to the special strength of the soul ceiling frame or a special frame for a water tank: a container filled with water has a significant weight.

Important: When the shock is trimmed by the shower walls, it is necessary to leave the gaps between the beams up to 3 mm for their expansion under the action of high humidity.

In the regions with a hot climate, there are options not to fully do the walls, but only a partial, closing torso person.

After the wall is trimmed, first of all, to secure the fungus, using antifungal impregnation for this. And then the structure is covered with water-based facade acrylic varnish in three layers. This will allow water, easily sliding, sliding, without lingering on the walls.

The floor can be made in the form of a lattice that allows water to drain into the pit, or solid, in which the flow of water is provided.

The last step in the soul device becomes the door hanging.

From polycarbonate

During the construction of the summer shower recently, this is increasingly used construction material Like polycarbonate. The construction of the shower design from it attracts its economy, ease of creation, strength and ease of care.

Polycarbonate sheets from 8 mm to 15 mm thick, having an opaque color, are well suited for shower walls. At the same time, they provide good heating during the day, and besides, it is maintained for a long time.

The building begins with the framework of the frame for the future soul.

Important: The soul frame of polycarbonate must be additionally strengthened with vertical, horizontal and diagonal jumpers. This will help ensure greater stability of the structure, taking into account the Polycarbonate sailboat.

Polycarbonate sheets without special problems are cut into a conventional knife to the desired dimensions, the edges of the cuts are processed by sandpaper.

For fastening polycarbonate sheets, it is necessary to use special fasteners: hardware having special hats that prevent water penetration, and thermoshaba. When attaching fasteners should not be twisted to the end - this will prevent the deformation of the sheet.

To protect the inner layer of the sheet of the resulting condensate, it is necessary to drill several holes in it. They can be arbitrarily located on a sheet, sufficient calculation - 3 per 1 square meter. m. At the same time, you should not drill a hole closer than 3-4 cm to the edge of the sheet, it will save it from possible chick.

Important: processing of polycarbonate walls of the shower special tool Promotes additional protection against ultraviolet radiation.

For the convenience of Dachnikov recently produced ready-made souls from polycarbonate. The seller can complete everything you need for self-installation of structures: sheets desired size Depending on the planned model, metal frame, anchor attachments. At the same time, sellers provide the buyer the ability to select the color of polycarbonate sheets.

From professional flooring

Another convenient way Building a shower in the country area involves the use of sheets of professional flooring as walls.

The construction of the shower cabin in this case is performed similarly to the already considered options, a wooden timber or metal pipes are traditionally used as a frame. But in any case, the constructed framework also requires additional strengthening by crossings.

Fasteners for professional flooring: galvanized self-tapping screws having a sealing washer. The mount is performed through one wave. Cutting professional flooring if necessary, performed by scissors or a grinder with a special disk with teeth.

From the utility materials

If the arrangement of the country site is just started, and the construction of the soul is still ahead, but the need for it is already felt, you can arrange a simple design from the utility materials.

In this case metal carcasswhich may at the bottom of having not only a rectangle, but also a circle, the moisture content material is attached as walls: dense polyethylene film or film shirma, it is also possible to use tarpaulin.

After installing the water tank, the shower is almost ready. The floor in it can serve a wooden grid and a rubber rug.

With all unassuming this design It has such advantages as:

• the speed and ease of construction, to create no more than two hours;
• mobility that allows you to move the facility from one place without any problems with one place to another and disassemble.

Brick shower

A more major and durable structure that perfectly fit into the interior of the country area is their summer souls from the brick.

In this case, the construction is complied with all the rules and rules for the construction of a brick house. With the construction of a brick house, you must consider the following:

summer shower, even brick,

- The construction is quite easy, which does not require a powerful foundation. It is enough to fill with concrete trench, the depth of which is up to 40 cm, width - 20 cm.

Important: When preparing the foundation, you should immediately install the pipe for a drain, otherwise it will be necessary to break the foundation later.

• under construction brick walls The soul can be done without plaster, but installation door box, as well as bars for further slate attachment in the last row of masonry - is required.

Container for water

Choosing the design of the future summer soul, it is impossible not to take into account such an important component of it as a water tank. Usually water in the shower is supplied from a metal galvanized or plastic tank installed on the roof.

When determining the size of the tank proceed from a possible number of users. The tank with a capacity of 200 l is a convenient option, as the experience of many dachensons shows.

Important: The color of the tank affects the degree of water heating in it. The darker the color of the water tank, the better it heats up the sun, and therefore water heats up faster in it.

Sometimes the tank mounted on the frame itself performs the functions of the cockpit roof.

In souls having a wall and a roof of polycarbonate, water tank is more expedient to install under the roof.

Until the installation of the container on the roof, it is necessary to strengthen the shower watering can, having done a hole in the container.

An important moment that needs to also be thought out in advance - a method of filling the tank with water. The most convenient option is to carry out a special pipe or fixing the constant water hose. If the option of such a liner is not possible, it is necessary to provide a place to install the stairs.

Important: When used as a tank for water adapted capacity, for example, barrels, it is necessary to protect it from trash and evaporation of water, using a special cover.

It is also possible to build a summer shower for ha heated. This requires a metal tank for water, in which heated - Ten is elected in advance. A sufficient device capacity is 2 kW.

By connecting the device to the power supply system, the summer heated shower can be used, being in the country, from early spring to late autumn, almost every weather.

Options are possible

Shower at the cottage is not necessarily a separate construction. Depending on the design of the site, taking into account the existing buildings, options are possible:

• available corner near country house It is possible to equip. This option will no longer require the framework of the frame. In addition, it becomes possible to remove the pipe from the house to supply water and equip it with a shower.

When solving the question, how to make a summer soul near the house, you must do the following:

• facing the outer wall at home with waterproof material;
• the use of a large pebble as a floor of a shower corner and at the same time - its drainage.

As the side fences of the Western Soul can perform natural screens from the grid with plants weekesting. The best choice Plants - curly, which will create a reliable and eco-friendly green screen - bind, ivy, grapes.

• convenient option - in Hozbok. The many years of experience of economic dachnikov confirms that the organization of the shower in a special nozpostroy is beneficial and comfortable.

Planning a hozblock is carried out with the placement of the shower there. Hozblok is built of bricks or special blocks, is a capital building. The branch for the shower will require the creation of a water and drainage system. But in the Hozclok with its durable walls, it is reliable: on its roof you can install a large water tanks.

• another option to ensure a comfortable stay at the cottage is the soul device in the country house.

This option is possible on a plot with built houses of a large area, in which there is a place for shower. To do this, in a specially designated place, a purchased ready shower room has a special pallet from acrylic. Water will be assigned with corrugated hose, the owners of the country house will only need to connect it to sewage.

Manufacturers of building materials make it possible to selected the prerequisites for the construction of any budget. BUT skillful hands The owner of the country area will be able to build a shower that will successfully fit into the interior of the site and will make a stay at the dacha truly pleasant to everyone!

Everyone wants the interior of his apartment is original and practical. Designs of finishing of shower rooms began to meet much more often, however, this invention cannot be called innovation.
Shower cabins were widely distributed thanks to the functionality, ease of installation, as well as considerable space saving, which is important in apartments with a small square. To date, manufacturers offer a wide range of these attributes in shape, color, materials from which they are made, which makes it easy to implement the most original and unusual project.

The design of the finishing of shower rooms can be completely different depending on the wishes and preferences of the host. Advantages of installation instead of the bathroom soul are estimated huge number of people.
There are many different interiors of these rooms, distinguished by a wide variety and various design solutions. When installing a shower cabin of free space, it becomes much more, which allows you to install a washing machine in the bathroom or other necessary items, such as furniture.
The priority task during repair in shower rooms is the selection of the necessary finishing materials that will be used. No one will be news that the bathroom is a room with high humidity, so materials that are resistant to the effects of steam and water will be required.
The decoration of the bathroom with a shower can be performed in various versions and the modern market offers a large assortment of materials that are successfully used when creating unique interiors in this room.

Council. In order to visually increase the space, you can use in the interior of mirrors, which are very relevant today in such interiors.

Materials for finishing

The traditional material that is successfully used to finish bathrooms has been ceramic tiles for a long time. It is very durable and has excellent aesthetic and operational characteristics, it is easy and very practical when used.

Council. If the room is small, then preference should be given not too large in size tile. This visually will increase the space of the bathroom.

So:

• Another option can be a magnificent material that does not respond to high humidity and temperature difference - this plastic panels. Manufacturers provide a huge selection of panels of various colors and sizes.
  If you wish to separate the shower room with your own hands, you will be surprised how easy it can be done, because they simply fit enough, thanks to the design features provided for.
• Also successfully used various paints. For repair in the shower room it is best to use latex paintsSince they are perfectly withstanding the impact of moisture.
  However, to repair with the use of this material pleased you for a long time, it is necessary to remember that it is originally (before painting) surfaces need to be processed correctly, as well as align.
• To finish bathrooms and shower rooms, you can use marble or other decorative rock. This luxury finishing material is characterized. long time services and low water absorption, but stack it own forces It is not recommended, as this is a very time-consuming and complex process, which requires significant experience.
• For the implementation of budget types of repair can be recommended self-adhesive film. A significant disadvantage of this material is its airtightness, which prevents the normal air exchange of the walls.

Stages of finishing work. Instruction

If you decide to repair in the shower room with our own forces, then the first stage in this case is dismantling work. It is necessary to repel the old tile, remove, remove or wash the old decoration Materials, disassemble the bathroom, old pipes, and then remove the entire construction trash.
This work is very dirty and physically difficult.

Council. Together with the dismantling of the old bathroom, it is also necessary to make a dismantling of pipes. It is best to remove them later into the walls or in special boxes, which can also be used in the future as shelves.

So:

• The second stage is the preparation of surfaces. At this stage, equalizing operations of all surfaces of the room are carried out. Very much at this stage depends on the selected room design and materials used.
• If you decide to paint the walls and the ceiling, then you need to bring them to the perfectly smooth state, since any of the operation will be noticeable any, even the smallest defects on the surface.
  In case you decide to use plastic panels for finishing, such alignment of walls is optional. You can not even dismantle the old finish.

Council. If you do not want to paint the ceiling, you can successfully use drywall, plastic panels, wood or very popular stretch ceilings that will be perfectly looked in the interior of the shower room.

• Third stage - floor finish. Depending on the selected material and the state of this surface in the room there may be necessary for those or other construction works.
  In order to better deal with the features of the finishes and laying of the floor, it is best to view a video in which all the stages and features of the implementation of such works are revealed.

The sex surface is more practical and the most aesthetically finished with ceramic tile or marble. Previously need to make a screed on cement based.
Laying tiles is a fairly time-consuming and complex process, so if you are not sure that you can carry out these works yourself at a high level, you must resort to the help of professionals.

Design and decoration of the shower room

So, in order to directly proceed to the repair work, first of all it is necessary to imagine (and the best way to draw) the interior design of the bathroom, and also choose all the materials necessary for the repair.

Council. If the bathroom room is small, it is necessary to take into account this fact when choosing a finish. In this case, a fine mosaic on the walls, which should be separated by a wall area located near the shower cabin.

Depending on the selected materials, the price of planned repairs will also fluctuate. Remember that you should not save on finishing materials to the detriment of their quality, since in this case the repairs will quickly lose its initial View And he will soon have to do again.

If you have a fairly limited budget, it is best to use more affordable finishing materials, such as plastic panels.
Today, their choice is quite wide, so you can easily implement the most different original ideas into reality. With this material it is easy to work quite easily, each can cope with the repairs.
If you have financial opportunities, you can advise you to try the decoration of the space around the shower with wood. Such an interior not only looks rich, but also creates a special impression, because a tree - natural materialwhich since ancient times was used to build a bath.

Council. When finishing a shower room, a tree should be given preference to the thickens of wood that have water-repellent properties. Great, for example, larch.
Impregnation with the compositions are required.

Wooden walls and floor fit perfectly in the most various interiors apartments and look amazing. Before designing the room with a tree, it is necessary to impregnate the walls with anti-grapple coating.
And at the end of color gamma. The design of shower rooms is best used pastel shadesand not contrast or dark.
However, if you prefer the latter, it should be borne in mind that it will be necessary to use bright lighting and desired not only ceiling, but also wall.