Interesting homemade products for giving are waiting for you in this article. You will learn how to make a lawn mower from an old washing machine, make a sink, country shower, a dryer from scrap materials.

Useful homemade products for giving - do it yourself washing

Not everyone has the financial opportunity to buy a car "Karcher". If you can't get it, then why not invent it? Homemade sink will allow you to do without running water, reduce water consumption and thoroughly wash your car, fence, garden path or other items.

Here's what you need for such a homemade product for a summer residence:

• plastic canister with a capacity of 5–20 liters;
• set of hose connectors;
• automobile nipple;
• a piece of hose;
• silicone sealant;
• sharp knife;
• compressor or car pump;
• watering gun.

Take a hose nozzle kit that includes 2 connectors, 3/4 threaded nipple, 1/2 reducer.

Here is the principle of operation of such a homemade product for a summer residence: you connect the gun to the hose, attach this device to the bottom of the canister. A nipple will be built into its neck.

Fill the container with water, but not to the top. Then screw the cap back on and pump air in. This will create pressure and water will run well when you pull the trigger of the gun. Here's how to assemble such a mini-sink.

Carefully cut a hole in the cover with the tip of a knife. It should be slightly less than the diameter of the nipple stem. Also cut a circle of the correct diameter at the bottom of the side of the canister.

Insert the nipple into the cover.

Now, helping yourself with the wire, put the sleeve in the hole provided for it. Apply silicone sealant to secure the junction of the sleeve to the canister.

It is necessary to tighten the lid and perform the rest of the work only after the sealant has completely solidified. Then you connect one end of the hose to the water gun and the other to the canister.

Pour water into a container, but not to the top, so that there is room for pumping air. But do not pump too much so that the canister does not deform or burst under pressure. See how the union should be screwed in and the connectors installed.

If everything is done correctly, then when you pull the trigger of the water pistol, the water will gush with a good stream. You can adjust the pressure by twisting the tip of the gun.

At the dacha, you can hardly do without a shower. Try to make an unusual, and tropical, then you can enjoy even more water treatments.

How to make a rain shower from scrap materials for a summer residence?

If you have just recently purchased a plot and you do not yet have a washing room, then you can take a shower right on the street by fencing small area near the fence with a curtain. To do this rain shower, very few components are required, these are:

• bracket;
• wire;
• flexible hose;
• metal beer can;
• hose adapter;
• awl;
• nails.

Nail the metal bracket onto wooden fence so that the attachment is at the correct height. Screw the adapter to the end of the hose, fix it on the slots of the beer can. The junction can be treated with a sealant. Use an awl to make many small punctures in the jar.

Wire the top of the hose to the bracket and attach the other end to the water supply or pump. When you lower the pump into a barrel of heated water, you will be able to take pleasant water treatments.

You can also make a rain shower head using a disc container as it. In its center, you need to fix a plastic adapter that is attached to the shower hose, and the central axis of the discs must be removed. Use an awl to make holes at the top of the cover. Glue all fasteners well with sealant. Such a nozzle is held on a bracket using a thick wire or on a rigid pipe.

If you have a desire to make a rain shower, then you can use plastic pipes for this.

You need to bring water to them, first make a lot small holes with a soldering iron and then enjoy the dripping drops. Children like such water procedures.

But do not forget to first check the water in the container from which it will be poured into the shower, it should warm up in the sun.

And to make a stationary shower, you must first pour water into a tank or barrel, which will be located under the roof or on the roof of the building. On a warm summer day, the water warms up well here, and you can wash yourself in plenty. To be able to do this even in cooler weather, then it is necessary to provide a heating system in such containers.

Country shower with your own hands

Before installing it, you need to make a shower stall. If possible, you can craft it out of wood by placing this small structure on the base. Put wooden door or limit yourself to this shower curtain.

There are more simple options... If you have oilcloth fabric, then use it.

Another option is to purchase an impregnated fabric or use an old awning or tent.

If you made a fence from corrugated board and you still have materials, then try to make a shower for giving out of them. Metal pipes you need to dig in according to the markings, fill them with concrete. When it dries, cut sheets of corrugated board are welded to the racks. One of them will become a roof.

If you have little wooden planks, then implement the option shown in the next photo on the right. And on the left is a shower, which is made like a wattle fence. So the materials for him will cost almost free.

When the shower is ready, you can install a water container on it. To make it warm better, you can make a kind of coil from metal or from a hose. Then the water will warm up more actively.

These and other homemade products for summer cottages allow you to make the most of the available containers.

To be able to receive warm water even when it is not heated by the sun, use electric heating. To do this, you can plastic barrel arrange vertically or horizontally. Then it will be necessary to mount the ten on one side, and on the other? water bay fitting. Make an overflow hole so that excess liquid flows out and you can see that the container is already full.

Now it remains to install the tank. Usually a shower roof is used for this. You can put a flat tank here, made of iron or plastic. You can also make a shower canister out of metal or iron barrel... If you need to heat the water, then a heating element is mounted in the barrel.

Check out other examples of what you can do on personal plot do it yourself.

Interesting homemade products for giving with your own hands

Gardening tools are essential for working on the ground. Often they don't sell very well in the store. quality sets... After a short time use, the handle of the shovel breaks off, or the teeth of the hoe are bent. Therefore, if possible, try to make the tools yourself.

Take:

• stalk;
• fragment of a water pipe;
• trim from a two-handed saw;
• screws;
• screws;
• fragment shaped pipe section 3 cm.

Using a grinder, cut a piece of pipe. Taking a lever tool, you need to cut out a piece of pipe, unbend the sector and in the place where the handle will be, you need to work with a hammer to give the future hoe the necessary outlines.

To make a blade, take a piece of a two-handed saw and sketch out the outlines of the future hoe. Punch two holes.

At the same distance and the same diameter, you need to make 2 holes on the hoe itself, and then cut out a fragment from a two-handed saw.

Drill these holes with a drill and drill designed for metalworking. Connect the two parts with rivets, which are screws.

Now drill a hole in the top of the hoe so you can attach the handle here.

Make also a scoop, which is very interesting to work in the beds. Then such homemade products for giving will allow you to find a very durable set of tools.

Saw off the desired piece of the cutting with a grinder and start unbending part of it with a chisel.

Then, using the lever tools, unbend this part almost completely.

It remains to work with a hammer so that the scoop blade takes the desired shape. Using a felt-tip pen, draw the outlines of its working part and cut it out with a grinder.

Use an abrasive wheel to smooth out the edges of the shovel and make them smoother. Now sand the tool with a flap wheel. This shovel will become so shiny.

Also drill a hole in it for the handle, then insert it and secure with a screw.

Cover the cuttings of both tools with antiseptic and then varnish. Now you can use the tools as intended. If you want, use the same principle to make a ripper for the beds.

It is very exciting to create such things for a summer residence with your own hands. Maybe after you make the tools, you want to make a fixture on which you can dry part harvested... See how one gardener did it.

How to make a dryer for fruits and vegetables?

See what materials you need to take for this:

• sheet metal;
• square pipes;
• locking mechanism;
• polycarbonate sheet;
• self-tapping screws, screws;
• 2 door hinges.

But what tools you need to arm yourself with:

• grinder;
• welding machine;
• drill;
• a clerical knife;
• tape measure and marker;
• scissors for metal;
• hacksaw.

First you need to make the base for the drying cabinet. Make a frame from square pipes... The horizontal and vertical posts are sawn off so that the edges are straight. And the tips on the connectors should be chamfered.

The door here will be metal. To make it, cut 4 fragments from the iron pipe and weld them into a rectangle. Then you need to sheathe this base with metal using screws with nuts and self-tapping screws. If possible, weld steel sheet... To make a baking tray holder, attach wooden blocks to the back of the frame. Take self-tapping screws for this. In this case, on each side there are 4 wooden blocks for 4 trays.

An absorber is installed in the dryer. Take sheets of metal and paint it black. Use heat resistant paint. When it's dry, place this blank on the bottom of the dryer.

For the absorber, take a thick aluminum or copper sheet, or at least steel. These materials conduct heat well.

Now you need to sheathe the outside of the dryer, make the roof transparent, made of polycarbonate. Then it will be good to penetrate here Sun rays... Glass can also be used. Close up ventilation windows mosquito net so that insects do not fly in here.

Attach the hinges and locking mechanism to the door. Reattach the door in place. Look, what a wonderful beautiful and spacious dryer turned out to be.

It remains to make baking sheets. They must be breathable. First, put together the frames from the bars, and then attach the metal mesh to them.

Now you can slice the fruit and watch your device work. Place a thermometer in the dryer to keep track of the temperature. It should be in the range of 50–55 ° С. If the temperature is colder, cover the bottom holes with a rag.

In such a homemade dryer, you can dry not only fruits, but also vegetables, spicy herbs, fish, meat, roots.

If this diagram of the device of such a device seemed complicated to you, then you can make a dryer out of metal barrel... A hole for the door is cut out in it, and racks made of metal mesh are inserted inside.

So that water does not flow here and there is better ventilation, such a roof is installed on top.

You can upgrade this fixture by installing a fan and an electric heater inside.

If you want to make your own lawn mower, then this is also possible.

Turn the old one into it washing machine, for example, this one.

And if you still have an old bedside table, then you will make a platform out of it for the future almost self-propelled device. But you only need a door from the bedside table.

Drill holes in the center of the motor shaft. Make a cutting knife from an old two-handed saw. It is necessary to saw off from it to size the desired shape, cut a recess inside.

Attach two wooden pickets that will become the handles of the mower. Remember to secure the motor and extension cord to it. Now you can test such an interesting unit.

If you are interested in other homemade products for giving, then it will be useful for you to watch the following video.

A lot of interesting ideas await you in the first video.

And with cool homemade products from plastic pipes you can get acquainted if you watch the second plot.

Nothing brings joy to your home like a handmade thing. Indeed, various homemade products for the home not only fill life bright colors, but also give the interior uniqueness and a certain zest. And it is certainly impossible to forget about such a thing (let it be a small trinket). And it is not so important that these are homemade products made of wood for the house, made of paper or plasticine. There are millions of options and methods for making various gizmos, and today we will consider a few of them. So how do you make interesting homemade products for your home?

Shelf from tin cans

It would seem that such a trifle is a can of coffee. However, even from it you can make a beautiful, convenient and useful shelf for storing household items. Often, various souvenirs and memorable photographs are stored in such containers. There is little practical use for this homemade product, but such jars look very harmonious.

Details about the manufacturing procedure for this craft

1. First, holes are punched in the jars with a drill or a special ripping knife (in the upper and lower - 3 points each, and in the walls of all the others - 2 points each).

2. Next, the jars are fastened together. Small nuts and screws are used as fasteners. By the way, to get the desired (beautiful) result, you will need to have at least 5-6 such jars.

3. After that, a hole is made in the containers for the screws. In the bottom of the jars located in the upper part of the structure, 1-2 holes are made for attaching the shelf to the wall. The finished homemade product is screwed with a screwdriver or screwdriver. Previously, dowels are driven into the wall for this.

That's it, now homemade products for the home are being put into business. Be sure - various little things in such jars will definitely not get lost. Thus, you kill two birds with one stone - decorate the interior and get rid of the clutter in the house.

DIY homemade - how to make a clock on a CD / DVD?

The clock on the CD is also quite interesting and original version interior decoration.

As you can see, the design of this device is very original, and therefore it will look organically against the background of any interior (it may become its highlight). Such "smart" homemade products are made for the house in a matter of minutes. We will tell you in more detail about all the stages below.

So how to do it yourself homemade watch? To begin with, you will need to prepare the appropriate materials - a CD / DVD CD (you choose the design of its front part at your discretion) and a case cover for it (the distance between the walls should be at least 0.05 centimeters). It is very important that the last part does not have any chips or scratches. To facilitate the work, you can purchase a ready-made watch and then simply replace the standard dial.

It must be a pointer, otherwise it will not work to make a homemade product. You should also make numbers. There should be a total of twelve of them. These can be cardboard, paper or plastic circles. Their thickness should not exceed two millimeters. Rhinestones can be used as decorations. You also need to prepare about 30-40 centimeters of wire, a piece of leather or fabric and superglue like "Moment". The main part of this whole construction will be a CD-disk. We will redo it in the first place.

First you need to mark the disk into twelve equal parts and glue the numbers on the marked points. In this case, the sectors should not go beyond outside diameter devices. How are homemade products made for the house further? After the sectors, we proceed to the clock itself - remove the arrows and place them exactly in the center of our disk. By the way, before attaching them, you can stick some kind of interesting photo, which will make the watch design even more original.

Use thin metal strips to increase the size of the arrows. To achieve the desired result, it is enough to apply glue on them and carefully position the part evenly over the entire surface of the guiding elements. The arrow mechanism itself is attached to the back of the disc.

What to do next?

So, the base of the watch is almost complete. The next step is to make holes in the device along the contour of the arrow mechanism. The field of this disc is installed in the case. The mechanism itself is brought out through the hole and tightly closed. Now, with the help of a wire, an emphasis is made, which is glued to the back cover. To make it more durable, glue a piece of fabric or leather on top of it. This will make the emphasis not only strong, but also beautiful, since the extra part of the wire no longer gapes on the clock as before. Everything, a homemade watch from a CD has been successfully manufactured. All that remains is to insert an AA battery and set the time. By the way, the battery can also be made by hand.

How to make a source of energy from lemon?

As we know, this fruit contains a lot of acid, respectively, with doing the right thing the lemon can be turned into a real mini battery.

Of course, the charge from such a "battery" will not be enough for work household appliances, however, for operation or charging mobile phone this current is sufficient.

Making homemade products for the home - preparing tools to turn lemon into a source of constant energy

In the course of work, you will need tools such as a knife, soldering iron, drill, iron pin, as well as a few pieces copper wire in isolation. Among other items, it should be noted the need for one glass or shot glass, a pair wooden sticks and the same number of pushpins. And, of course, our main source of energy will be lemon. You can also use an orange, but there is much less acid in it, so the charge from it will be minimal.

Instructions

First, cut the lemon in half. This is so that it gives more acid, which is necessary for the lemon to be fixed in the glass so that it does not roll on the table. Further, copper and iron pins are inserted into its pulp along the entire perimeter at a distance of 0.5-1 centimeters. Our minus will be iron, and our plus will be copper.

Pieces of wire are attached to all pins with a soldering iron. They will act as a power supply connector. All elements are connected in series.

On final stage sticks are inserted into the battery compartment. The polarity is important here. The contacts are pressed against the contact group. The container remains open throughout the entire charging process.

So, we figured out how to make useful DIY homemade products for your home. Good luck in your endeavors!

As they say, there is never a lot of space in the garage. Men who spend a lot of time in the garage will agree that in some cases, every minute and every square centimeter of free space counts. That is why the garage master needs a competent organization of the workspace. Here various people help out and help in every possible way. devices for storing building materials, work equipment, machine parts and other things necessary for work. To keep your electronic, garden and garage gadgets in place, use the following tools:

• • stands;
  • shelves;
  • sliding panels;
  • racks;
  • organizers for tools.

Also, for clarity, we offer homemade products for the garage and home master do it yourself - the YouTube video will reveal all the nuances of organizing the workspace and suggest fresh ideas.

DIY homemade products

Man began to engage in homemade homemade products since prehistoric times. Actually, all industrial processes are improved once artisanal or home developments craftsmen... We sometimes do not even think that we are paying for the things that we can do with our own hands. Homemade homemade schemes are easy to find online, and materials can be purchased at a hardware store or found at home.

For example, from cardboard box and a piece of cloth can be made comfortable portable organizer for towels and other textiles.
The topic of storing all sorts of little things is inexhaustible, fortunately, as is the number of ideas. Successful decor ideas you can also draw from ordinary things - let them be buttons or empty cans.
Cool shelves are obtained from regular drawers... How do you like this idea?

How did you manage to understand, if there is detailed instructions it is not so difficult to make homemade products with your own hands at home. The video will help you comprehend all the nuances of this pleasant activity. Useful Tips, interesting ideas- everyone must watch.

Homemade products for a summer residence and a garden with their own hands

At the dacha, there is usually a little free time for creativity and arrangement of the surrounding space. That's why it is worth having a few fresh ideas to embody them in your own summer cottage. Country homemade products at home with their own hands can be ingeniously simple. From the materials at hand, you can make unexpected and extremely useful things in your household.

Ordinary stones turn into fairy animals.From an old teapot it turns out to be a wonderful flower pot.

Used tires- it has already become a classic in the world garden figures.Stylish lamps for the country interior - do it yourself from a regular can and candles (do not forget about safety precautions).
- a great idea for a small summer cottage.
Do-it-yourself homemade products for a summer residence and a vegetable garden are often obtained by themselves, without unnecessary time and financial costs. Perhaps you did not know how useful for household will be plastic bottles. Retired plastic bottles can serve as the basis for an incredible decorative flower bed. Cool "blooming" pillars will significantly decorate your summer cottage space.

DIY garden furniture successful homemade products: photos and drawings

In the previous sections, we told you about homemade products that will become indispensable for the household and home life... However, do not forget about the rest, before which, nevertheless, you will have to work a little. Cozy armchairs, various tables and benches, swings and hammocks- all this dacha and garden bliss can settle on your site. We suggest that you familiarize yourself with the photo instructions and drawings for manufacturing garden furniture... We have selected the best options for you.

Since you have decided to become a self-taught electrician, then surely after a short period of time you will want to make some useful electrical appliance for your home, car or summer cottage with your own hands. At the same time, homemade products can be useful not only in everyday life, but also made for sale, for example,. Actually the build process simple devices at home is not difficult. You just need to be able to read the diagrams and use the tool for radio amateurs.

As for the first point, before you start making electronic homemade products with your own hands, you need to learn how to read electrical circuits. In this case, ours will be a good helper.

From tools for novice electricians, a soldering iron, a set of screwdrivers, pliers and a multimeter will come in handy. For the assembly of some popular electrical appliances, you may even need welding machine but this is a rare case. By the way, in this section of the site we even talked about the same welding machine.

Special attention should be paid to the materials at hand, from which every newbie electrician can make elementary electronic homemade products with his own hands. Most often, old domestic parts are used in the manufacture of simple and useful electrical appliances: transformers, amplifiers, wires, etc. In most cases, it is enough for novice radio amateurs and electricians to look for all the necessary tools in the garage or shed in the country.

When everything is ready - the tools are collected, spare parts are found and minimal knowledge received, you can proceed to the assembly of amateur electronic homemade products at home. This is where our small guide will help you. Each instruction provided includes not only detailed description each of the stages of creating electrical appliances, but is also accompanied by photo examples, diagrams, as well as video lessons in which the entire manufacturing process is clearly shown. If you do not understand at some point, then you can clarify it under the entry in the comments. Our experts will try to advise you in a timely manner!

A summer cottage is the territory where you can give yourself freedom to carry out numerous experiments and dream up to your heart's content. This manifests itself not only in interior design, but mainly in the design of the garden or vegetable garden. Inquisitive and inventive owners have not been guided by expensive and standard methods for the arrangement of their sites, since there are many alternative solutions for virtually all areas of activity.

There are several types of vertical beds that allow you to optimize the use of free space. Custom designs are a great opportunity to create interesting design garden, vegetable garden, suburban area.

This type of beds in most cases is used for growing ornamental plants or spicy herbs.

Materials for making:

The length of the drainpipes is regulated in accordance with the wishes of the owner of the site. However, cumbersome beds should not be made, as they can complicate movement across the territory.

Creating a garden

Stage 1. Create a container. To do this, we take a drainpipe, cut it in half lengthwise and put on special plugs on both sides.

Stage 2. We take the prepared metal holders, put them on the received frames for the beds.

Stage 3. We make holes in the pipe. They are made in those places where metal fasteners will be located.

Stage 4. We pass a cable or a strong rope through the holes made.

Stage 5. We fix the cable / rope with fasteners.

Stage 6. We fill the resulting beds with expanded clay and soil.

Stage 7. We plant the plants in the beds.

Stage 8. We hang the pipes to the chosen place. Sometimes a special wooden crossbar is placed for this, or rather a construction in the shape of the letter "P".

Step 9. Alternatively, you can make a special design for the pipes.

Important! A bed of drainpipes is not resistant to strong gusty winds, so you should choose a place for it that is not blown from four sides by winds. V otherwise, the frame will quickly collapse, nullifying all your efforts.

A bed made of a plastic bag is another modification of vertical beds. It is extremely compact, functional and externally interesting. You can make such a bed in a couple of hours.

Materials for making:

• durable plastic wrap;
• sewing machine;
• priming;
• seedling.

In order for the bed to turn out to be durable, it is recommended Special attention give thickness plastic film, which in this case will act as a "frame" of the structure. Minimum thickness films - 0.2 millimeters.

The process of creating a plastic bed

Step 1 . We cut out 2 rectangular film segments, the size of which corresponds to the size created beds... An allowance of one and a half to two centimeters should be left on each side. The recommended bed diameter is twenty centimeters.

Step 2. Sew the rectangles together, leaving only the upper part of the bag unconnected.

Step 3. Sew a handle to the future garden bed, the strength of which will support the weight of the bag filled with soil. It should also be borne in mind that when watering, the weight will increase.

Step 4. Fill the bag with fertilized soil.

Step 5. Make horizontal cuts on the bag in twenty centimeters increments. They are necessary in order to plant seedlings in the garden bed.

Step 6. We plant seedlings.

Step 7. Water the soil regularly and add the necessary fertilizers.

With these simple steps, you can get a cheap and useful garden bed.

An integral element of every summer cottage is a compost heap. This is the place where all kinds of biochemical reactions take place that ensure the creation of fertilizers.

To create fertilizers that will satisfy all the requirements for them, you should carefully consider several key steps: creating a container and directly correct manufacturing the compost itself. Let's talk about each of them in more detail.

Stage 1. Take eight support posts of the same length.

Stage 2. We process the bottom of the wooden posts engine oil or tar.

Stage 3. We dig the posts into the ground so that they are reliable and stable. If compost bin will be located next to the fence, then 4 posts (that is, one side) can be attached to the fence. This will avoid having to dig 4 holes.

Stage 4. Between each two adjacent posts we nail the crossbeams in such a way that we end up with three independent sections. Be sure to leave slots that will function as ventilation holes.

Stage 5. In two sections, we nail the boards horizontally to half the height of the posts. In these places, it is planned to create two small doors.

Step 6. The remaining section will big door so only one plank should be nailed down. It should be located at the very bottom in a horizontal position, that is, like a regular crossbar.

Stage 7. Installing the covers. You can use one large solid board for this.

Stage 8. Install the pre-prepared doors.

Stage 9. We provide doors with handles and latches.

Stage 10. We process wood using special impregnations.

Step 11. Paint the box any color that suits your preferences.

Many gardeners mistakenly believe that any component can be dumped into a compost heap. In fact, to create the right biofertilizer, you need to carefully select the "ingredients".

Among the mandatory components of a compost heap are the following:

• peat;
• ash;
• needles;
• tree branches;
• leaves;
• hay or grass;
• wood ash;
• plant roots;
• raw vegetables and fruits, etc.

All elements are randomly mixed on the heap. To speed up chemical reactions it is recommended to cover the pile with a tarp (this is especially true in the absence of a box).

Trips to the country house with the family involve the presence of entertainment elements on the site that will delight children. The most common way to keep young summer residents busy is with a swing.

Building a swing yourself is not an easy task, but quite doable. Of course, you can always take a stick, tie it with a rope and hang the structure on a tree, but this can hardly be called a full swing. True craftsmen prefer to construct comfortable designs with a comfortable seating position.

Constructive components:

• two logs;
• strong rope.

Indicators:

• diameter of logs - 85 mm;
• log length - 700 mm;
• the distance between the ropes is 500 mm.

Making a swing

Stage 1. We stretch the ropes between the logs.

Stage 2. We wrap each log with ropes.

Stage 3. We release the ropes out.

Stage 4. We tighten the ropes by 3 knots.

Stage 5. We fix the swing on the tree.

Important: such a swing is designed for only one person.

Garden path from scrap materials

There are several types of garden paths that you can easily do with your own hands.

Step 1. Remove the sidewall from the tire using a knife or saw.

Step 2. Cut the tires.

Step 3. We line the space with grooved stripes.

Step 4. We paint the path with paint.

Step 5. Sprinkle with stone chips.

it economical option for those who do not want to rack their brains and waste time on a full-fledged garden path. The tire track is usually used for vegetable gardens, as it easily fits into the ground.

Stage 1. We paint the corks in different colors.

Stage 2. We dig a small trench.

Stage 3. We drive in supports to strengthen the future track.

Stage 4. We build the formwork using boards.

Step 5. Install spacers along the edges of the trench.

Stage 6. We place crushed stone deep into the trench and carefully tamp it.

Stage 7. We make a mortar from sand, cement, glue and water.

Stage 8. Pour the solution into the trench.

Stage 9. Press the plugs in random order. Even multi-colored stripes look interesting.

These are the simplest and quick ways make a garden path without purchasing expensive materials.

DIY tools

The expression "everything will come in handy on the farm" is most relevant when it comes to canisters. This plastic container can be made a large number of indispensable tools that are actively used in the process of summer cottage work.

To make this tool, we only need a sharp knife and the container itself.

Stage 1. Cut off the bottom of the canister.

Stage 2. We mark on the container the cut line for the scoop so that the handle from the canister is the handle of the future tool.

Stage 3. Cut off excess material.

As a result of these simple steps, we get an excellent scoop with a comfortable handle.

Materials:

Manufacturing

Stage 1. Carefully wash the canister so that there is no smell left in it.

Stage 2. We cut the canister vertically into two parts.

Step 3. Make a groove on the plank using a woodworking machine.

Stage 4. Apply glue to the plywood and insert into the bottom of the canister.

Stage 5. We paint the resulting shelf with a spray can.

Of course, such a structure will not withstand a lot of weight, but it is quite suitable for storing small parts.

Materials:

• 40 cans;
• scissors;
• rope;
• paper;
• marker.

Stage 1. We pierce the upper part of the cans with a knife.

Stage 2. We make a stencil out of paper.

Stage 3. We apply it to the canister, outline it with a marker.

Step 4. Cut out large holes with scissors.

Stage 5. We put the prepared cans in several rows, tying each row by prying the rope under the handles of the containers.

Stage 6. We tie all the rows around the perimeter for greater strength.

Stage 7. If the cabinet is planned to lean against the wall, then we drill it to the surface.

Stage 8. We put heavy objects in the bottom row - stones or bricks.

The result is a fairly roomy and functional rack that will help get rid of the issue of storing many small parts.

Be resourceful and courageous in bringing your ideas to life. Good luck!

Video - DIY homemade products

Video - We do it ourselves for giving